Scribd
Upload
51 views3 pages

Aluminum 5052

Aluminum 5052-H32 is an aluminum alloy containing magnesium as the major alloying element. It has the following typical properties: - Density of 2.68 g/cc - Hardness of 60 on the Brinell scale - Tensile yield strength of 193 MPa and ultimate tensile strength of 228 MPa - Elongation at break of 12% for thickness testing and 18% for diameter testing

Uploaded by

Luis Esteves
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
51 views3 pages

Aluminum 5052

Aluminum 5052-H32 is an aluminum alloy containing magnesium as the major alloying element. It has the following typical properties: - Density of 2.68 g/cc - Hardness of 60 on the Brinell scale - Tensile yield strength of 193 MPa and ultimate tensile strength of 228 MPa - Elongation at break of 12% for thickness testing and 18% for diameter testing

Uploaded by

Luis Esteves
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Aluminum 5052-H32

Subcategory: 5000 Series Aluminum Alloy; Aluminum Alloy; Metal; Nonferrous Metal
Close Analogs:
Composition Notes:
Aluminum content reported is calculated as remainder.
Composition information provided by the Aluminum Association and is not for design.
Key Words: NS A!505"; #S$ AlMg".5; Aluminium 505"%&'"; AA505"%&'"
Component Wt !
Al !5.( % !(.(
Cr 0.)5 % 0.'5
Cu Ma* 0.)
+e Ma* 0.,
Component Wt !
Mg "." % ".-
Mn Ma* 0.)
$ther. each Ma* 0.05
Component Wt !
$ther. total Ma* 0.)5
Si Ma* 0."5
/n Ma* 0.)
"aterial Notes:
0ata points 1ith the AA note have been provided by the Aluminum Association. #nc. and are N$2 +$3
04S#5N.
#$ysical #roperties "etric %nglis$ Comments
0ensity 2.68 g/cc 0.0!6- lb7in8
AA; 2ypical
"ec$anical #roperties
&ardness. 9rinell 60 60
AA; 2ypical; 500 g load; )0 mm ball
&ardness. :noop -' -'
Converted from 9rinell &ardness
;alue
&ardness. ;ic<ers 6- 6-
Converted from 9rinell &ardness
;alue
ltimate 2ensile Strength 228 MPa ''000 psi
AA; 2ypical
2ensile =ield Strength 193 MPa "-000 psi
AA; 2ypical
4longation at 9rea< 12 % )" >
AA; 2ypical; )7)6 in. ?).6 mm@
2hic<ness
4longation at 9rea< 18 % )- >
AA; 2ypical; )7" in. ?)".( mm@
0iameter
Modulus of 4lasticity 70.3 GPa )0"00 <si
AA; 2ypical; Average of tension and
compression. Compression modulus is
about "> greater than tensile modulus.
AoissonBs 3atio 0.'' 0.''

+atigue Strength 117 MPa )(000 psi
AA; 500.000.000 cycles completely
reversed stress; 33 Moore
machine7specimen
Shear Modulus 25.9 GPa '(60 <si

Shear Strength 138 MPa "0000 psi
AA; 2ypical
%lectrical #roperties
4lectrical 3esistivity 4.99e-006 ohm-
cm
,.!!e%006 ohm%cm
AA; 2ypical at 6-C+
&$ermal #roperties
C24. linear 6-C+ 23.8 m/m-C )'." Din7in%C+
AA; 2ypical; Average over 6-%")"C+
range.
C24. linear "50CC 25.7 m/m-C ),.' Din7in%C+
Average over the range "0%'00EC
Specific &eat Capacity 0.88 J/g-C 0.") 927lb%C+
4stimated from trends in similar Al
alloys.
2hermal Conductivity 138 W/m-K !60 92%in7hr%ftF%C+
AA; 2ypical at ((C+
Melting Aoint 60( % 6,! CC ))"5 % )"00 C+
AA; 2ypical range based on typical
composition for 1rought products )7,
inch thic<ness or greater
Solidus 607 C ))"5 C+
AA; 2ypical
GiHuidus 649 C )"00 C+
AA; 2ypical
#rocessing #roperties
Annealing 2emperature 343 C 650 C+
holding at temperature not reHuired
&ot%Ior<ing 2emperature "60 % 5)0 CC 500 % !50 C+

You might also like