Introduction to Nondestructive

Testing

Outline
Introduction to NDT
Overview of Six Most
Common NDT Methods
Selected Applications
The use of noninvasive
techniques to determine
the integrity of a material,
component or structure
or
quantitatively measure
some characteristic of
an object.
i.e. Inspect or measure without doing harm.
Definition of NDT
Methods of NDT

Visual
What are Some Uses
of NDE Methods?
Flaw Detection and Evaluation
Leak Detection
Location Determination
Dimensional Measurements
Structure and Microstructure Characterization
Estimation of Mechanical and Physical Properties
Stress (Strain) and Dynamic Response
Measurements
Material Sorting and Chemical Composition
Determination

Fluorescent penetrant indication
When are NDE Methods Used?
To assist in product development
To screen or sort incoming materials
To monitor, improve or control
manufacturing processes
To verify proper processing such as heat
treating
To verify proper assembly
To inspect for in-service damage
There are NDE application at almost any stage
in the production or life cycle of a component.
Six Most Common NDT
Methods
Visual
Liquid Penetrant
Magnetic
Ultrasonic
Eddy Current
X-ray &
Radiographic

Most basic and common
inspection method.

Tools include
fiberscopes,
borescopes, magnifying
glasses and mirrors.
Robotic crawlers permit
observation in hazardous or
tight areas, such as air
ducts, reactors, pipelines.
Portable video inspection
unit with zoom allows
inspection of large tanks
and vessels, railroad tank
cars, sewer lines.
Visual Inspection
A liquid with high surface wetting characteristics
is applied to the surface of the part and allowed
time to seep into surface breaking defects.
The excess liquid is removed from the surface
of the part.
A developer (powder) is applied to pull the
trapped penetrant out the defect and spread it
on the surface where it can be seen.
Visual inspection is the final step in the
process. The penetrant used is often loaded
with a fluorescent dye and the inspection is
done under UV light to increase test
sensitivity.
Liquid Penetrant Inspection
Magnetic Particle Inspection
The part is magnetized. Finely milled iron particles coated with a
dye pigment are then applied to the specimen. These particles
are attracted to magnetic flux leakage fields and will cluster to
form an indication directly over the discontinuity. This indication
can be visually detected under proper lighting conditions.
Magnetic Particle Crack Indications
Radiography
The radiation used in radiography
testing is a higher energy (shorter
wavelength) version of the
electromagnetic waves that we
see as visible light. The radiation can
come from an X-ray generator or a
radioactive source.
High Electrical Potential
Electrons
- +
X-ray Generator
or Radioactive
Source Creates
Radiation
Exposure Recording Device
Radiation
Penetrate
the Sample
Film Radiography
Top view of developed film
X-ray film
The part is placed between the
radiation source and a piece of film.
The part will stop some of the
radiation. Thicker and more dense
area will stop more of the radiation.
= more exposure
= less exposure
The film darkness
(density) will vary with
the amount of radiation
reaching the film
through the test object.
Radiographic Images
Conductive
material
Coil
Coil's
magnetic field
Eddy
currents
Eddy current's
magnetic field
Eddy Current Testing
Eddy Current Testing
Eddy current testing is particularly well suited for detecting surface
cracks but can also be used to make electrical conductivity and
coating thickness measurements. Here a small surface probe is
scanned over the part surface in an attempt to detect a crack.
High frequency sound waves are introduced into a
material and they are reflected back from surfaces or
flaws.

Reflected sound energy is displayed versus time, and
inspector can visualize a cross section of the specimen
showing the depth of features that reflect sound.
f
plate
crack
0 2 4 6 8 10
initial
pulse
crack
echo
back surface
echo
Oscilloscope, or flaw
detector screen
Ultrasonic Inspection (Pulse-Echo)
Ultrasonic Imaging
Gray scale image produced using
the sound reflected from the front
surface of the coin
Gray scale image produced using the
sound reflected from the back surface
of the coin (inspected from heads side)
High resolution images can be produced by plotting
signal strength or time-of-flight using a computer-
controlled scanning system.
Common Application of NDT
Inspection of Raw Products
Inspection Following Secondary
Processing
In-Services Damage Inspection
Inspection of Raw Products
Forgings,
Castings,
Extrusions,
etc.
Machining
Welding
Grinding
Heat treating
Plating
etc.
Inspection Following
Secondary Processing
Cracking
Corrosion
Erosion/Wear
Heat Damage
etc.
Inspection For
In-Service Damage
Power Plant Inspection
Probe
Signals produced
by various
amounts of
corrosion
thinning.
Periodically, power plants are
shutdown for inspection.
Inspectors feed eddy current
probes into heat exchanger
tubes to check for corrosion
damage.
Pipe with damage
Wire Rope Inspection
Electromagnetic devices
and visual inspections are
used to find broken wires
and other damage to the
wire rope that is used in
chairlifts, cranes and other
lifting devices.
Storage Tank Inspection
Robotic crawlers
use ultrasound to
inspect the walls of
large above ground
tanks for signs of
thinning due to
corrosion.
Cameras on
long
articulating
arms are used
to inspect
underground
storage tanks
for damage.

Aircraft Inspection
Nondestructive testing is used
extensively during the
manufacturing of aircraft.
NDT is also used to find cracks
and corrosion damage during
operation of the aircraft.
A fatigue crack that started at
the site of a lightning strike is
shown below.
Jet Engine Inspection
Aircraft engines are overhauled
after being in service for a period
of time.
They are completely disassembled,
cleaned, inspected and then
reassembled.
Fluorescent penetrant inspection
is used to check many of the parts
for cracking.
Sioux City, Iowa, July 19, 1989
A defect that went
undetected in an
engine disk was
responsible for
the crash of
United Flight 232.
Crash of United Flight 232
Pressure Vessel Inspection
The failure of a pressure vessel
can result in the rapid release of
a large amount of energy. To
protect against this dangerous
event, the tanks are inspected
using radiography and
ultrasonic testing.
Rail Inspection
Special cars are used to
inspect thousands of miles
of rail to find cracks that
could lead to a derailment.
Bridge Inspection
The US has 578,000
highway bridges.
Corrosion, cracking and
other damage can all
affect a bridges
performance.
The collapse of the Silver
Bridge in 1967 resulted in
loss of 47 lives.
Bridges get a visual
inspection about every 2
years.
Some bridges are fitted
with acoustic emission
sensors that listen for
sounds of cracks growing.

NDT is used to inspect pipelines
to prevent leaks that could
damage the environment. Visual
inspection, radiography and
electromagnetic testing are some
of the NDT methods used.
Remote visual inspection using
a robotic crawler.
Radiography of weld joints.
Magnetic flux leakage inspection.
This device, known as a pig, is
placed in the pipeline and collects
data on the condition of the pipe as it
is pushed along by whatever is being
transported.
Pipeline Inspection
Special Measurements
Boeing employees in Philadelphia were given the privilege of
evaluating the Liberty Bell for damage using NDT techniques.
Eddy current methods were used to measure the electrical
conductivity of the Bell's bronze casing at various points to
evaluate its uniformity.