Scribd
Upload
541 views

Threaded Rod, ASTM A193 B7, Plain: Page 1 of 2 REV-03 Date: December 1, 2010 TROD.B7.P

This document provides product standards for threaded rod made of ASTM A193 B7 steel. It specifies dimensional requirements such as diameters and tolerances that must be met. Chemical and mechanical properties are also referenced from the ASTM specification. Threads must be rolled according to ASME standards and coated in light protective oil. Material test reports documenting full chemical and mechanical properties must be supplied for each lot to ensure specification compliance.

Uploaded by

ecruz_yhwh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
541 views

Threaded Rod, ASTM A193 B7, Plain: Page 1 of 2 REV-03 Date: December 1, 2010 TROD.B7.P

This document provides product standards for threaded rod made of ASTM A193 B7 steel. It specifies dimensional requirements such as diameters and tolerances that must be met. Chemical and mechanical properties are also referenced from the ASTM specification. Threads must be rolled according to ASME standards and coated in light protective oil. Material test reports documenting full chemical and mechanical properties must be supplied for each lot to ensure specification compliance.

Uploaded by

ecruz_yhwh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2

Date: December 1, 2010

Fastenal Product Standard

REV-03
TROD.B7.P

Threaded Rod, ASTM A193 B7, Plain


The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If
the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your
status as an approved vendor. Unless otherwise specified, all referenced consensus standards must be adhered to in their entirety.

D (Major Diameter)
Max.
Min.
10-24 *
.1900
.1890
.1818
10-32 *
.1900
.1891
.1831
.2500
.2489
.2367
1/4-20
1/4-28
.2500
.2490
.2392
5/16-18
.3113
.2982
.3125
5/16-24
.3125
.3114
.3006
3/8-16
.3750
.3737
.3595
3/8-24
.3750
.3739
.3631
7/16-14
.4375
.4361
.4206
7/16-20
.4375
.4362
.4240
1/2-13
.5000
.4985
.4822
1/2-20
.5000
.4987
.4865
9/16-12
.5625
.5609
.5437
9/16-18
.5611
.5480
.5625
5/8-11
.6250
.6233
.6051
5/8-18
.6250
.6236
.6105
3/4-10
.7500
.7482
.7288
3/4-16
.7500
.7485
.7343
7/8-9
.8750
.8731
.8523
7/8-14
.8750
.8734
.8579
1-8
.9980
.9755
1.000
1-14 *
1.000
.9984
.9881
1 1/8-7
1.125
1.1228
1.0982
1 1/8-8 *
1.125
1.1229
1.1079
1 1/8-12
1.125
1.1232
1.1060
1 1/4-7
1.250
1.2478
1.2232
1 1/4-8 *
1.250
1.2479
1.2329
1 1/4-12
1.250
1.2482
1.2310
1 3/8-6
1.3726
1.3453
1.375
1 3/8-8 *
1.375
1.3728
1.3578
1 3/8-12
1.375
1.3731
1.3559
1 1/2-6
1.500
1.4976
1.4703
1 1/2-8 *
1.500
1.4978
1.4828
1 1/2-12
1.500
1.4981
1.4809
1 5/8-8 *
1.625
1.6228
1.6078
1 5/8-12
1.6232
1.6118
1.625
1 3/4-5
1.750
1.7473
1.7165
1 3/4-8 *
1.750
1.7477
1.7327
1 3/4-12
1.750
1.7482
1.7368
1 7/8-8 *
1.875
1.8727
1.8577
2-4.5
2.000
1.9971
1.9641
2-8 *
2.000
1.9977
1.9827
2-12
2.000
1.9982
1.9868
2 1/4-8 *
2.250
2.2476
2.2326
2 1/2-8 *
2.4976
2.4826
2.500
* Class 2A threads shall be used for sizes where 1A is not applicable
Diameter

Nominal Size

Length
3'
6' - 12'

Tolerance
+/- 1/4"
+/- 1/2"

Length shall be measured form end to end

Page 2 of 2
Date: December 1, 2010

Fastenal Product Standard

REV-03
TROD.B7.P

Specification Requirements:

Standard:
Material &
Mechanical Properties:
Thread requirements:
Coating:
Product Marking:

Material Test Reports:

ASME B18.31.3
ASTM A193/A193M, B7.
Roll threaded to ASME B1.1 UNC, UNF, 8UN and UNS Class 1A.
Light protective oil.
Marked with predetermined color on rod end.
Vendor to supply color code with the MTR and purchase order.
The MTR must have documented lot traceability, including full
chemical and mechanical figures, to the specification(s) above.

You might also like