September 2014

www.chemengonline.com
The Future of
Butadiene
Facts at Your
Fingertips:
Safe Sampling of
Heat-Transfer Fluids
Extruders
Evolve for
the New World
PUMPS:
M0Nl|0 08|kl
Ml08N|0l 8ll8
2-P8 Il08l 8lP08
STARTS ON
PAGE 56
PAGE
46
Focus on
Valves
YOU WlLL TUPN W^3TLW^TLP
lNTO WOPKlN0 W^TLP.
Dow's expert|se |n reverse osuos|s, u|tru||trut|on und |on exchunge techno|og|es |s
uu||ng u reu| d|erence or uunuucturers ucross the g|obe, he|p|ng to trunsoru
wustewuter |nto useub|e wuter or u broud runge o upp||cut|ons-wh||e ueet|ng
str|ngent d|schurge requ|reuents, suv|ng energy costs und boost|ng upt|ue.
Make Real Progress.
To |nd out how Dow cun he|p you put wustewuter buc| to wor|, w|th uore
e|c|ency und |ess energy, v|s|t us ut MakeRealProgress.com
WATER & PROCESS SOLUTIONS

T
h
e

D
O
W

D
i
a
m
o
n
d

L
o
g
o
,

S
o
l
u
t
i
o
n
i
s
m

a
n
d

d
e
s
i
g
n

a
r
e

t
r
a
d
e
m
a
r
k
s

o
f

T
h
e

D
o
w

C
h
e
m
i
c
a
l

C
o
m
p
a
n
y

2
0
1
4
Circle 18 on p. 76 or go to adlinks.che.com/50980-18
SEPTEMBER 2014 VOLUME 121, NO. 9
COVER STORY
46 Cover Story Part 1 Modern Water-Treatment Challenges
Using the liquefied natural gas (LNG) industry as an example,
this article explores the challenge of ensuring the purity of inlet
and outlet water
51 Cover Story Part 2 Challenges of Drying Sticky Wastewater
Sludge In wastewater-sludge drying and dewatering operations,
many issues arise from the the sticky properties of the sludge.
Here are some insights to address them
NEWS
11 Chementator Demonstration plants for biomass-to-sugar technology
under construction; Mercury removal with modified aluminosilicate
clay; This process realizes large cost savings for manufacturing silicon
wafers; Commercial debut planned for an FCC process with enhanced
olefins production; A more direct route to ethyl acetate; and more
19 Newsfront The Future of Butadiene Butadiene scarcity, imposed
by the shift toward ethane cracking, provides opportunities for the
development of new technologies
26 Newsfront Extruders Evolve for the New World A changing
marketplace necessitates extrusion equipment with greater flexibility
and higher efficiency
ENGINEERING
44 Facts at Your Fingertips Safe Sampling of Heat-Transfer Fluids
This one-page reference helps readers understand the safety hazards
associated with sampling of heat-transfer fluids for quality check-ups
45 Technology Profile Producing 1,4-butanediol from bio-succinic
acid This one-page profile describes a process for producing the ver-
satile intermediate chemical 1,4-butanediol (BDO) from biologically
derived succinic acid
56 Feature Report Part 1 Magnetically Driven Pumps: An Overview
Understanding sealless pump technologies and their potential
applications
62 Feature Report Part 2 Mechanical Seals Update: Pharmaceuti-
cal and Food Applications For applications that require cleanliness,
be sure your centrifugal pumps have the proper seals
www.chemengonline.com
56
62
46
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 1
19
2 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
EQUIPMENT & SERVICES
32I-1 Show Preview Powtech 2014 From Sept. 300ct. 2, the
Nuremburg (Germany) exhibition center will play host to Powtech
2014, a trade fair focused on handling bulk solid materials and
powders. Descriptions of selected products to be on exhibit are
included here (International issue only)
33 Focus on Valves and Actuators Thermoplastic butterfly valve
enables many stopping positions; Valve handles high-molecular-
weight fluids in compressors; Check valve prevents backflow
and odor at discharge points; Full plastic construction provides a
range of advantages; Family of forged valves is ideal for severe
operating conditions; and more
36 New Products A new line of electrically driven solids-handling
pumps; Intelligent and robust fuel flowmeters and readout units;
A new generation of dry-running agitator seals; This control
system now has enhanced alarm functions; These dry vacuum
pumps have a high throughput; and more
41 Show Preview Weftec 2014 The annual Weftec exhibition and
conference will take place from Sept. 27Oct. 1 in New Orleans,
La. for the water and wastewater industries. Here is a selection of
products scheduled to be showcased on the exhibit floors
COMMENTARY
5 Editors Page Making security a priority
Heightened government activity spurred by two Executive orders
further builds the groundwork needed to address security concerns
in the CPI
65 The Fractionation Column The practical side of R&D
The columnist discusses a recent presentation that makes a case
for companies to be disciplined in their research and development
projects
DEPARTMENTS
6 Letters
8 Bookshelf
76 Reader Service
78 Whos Who
79 Economic Indicators
ADVERTISERS
66 Special Advertising Section on Water
75 Product Showcase/Classified
77 Advertiser Index
COMING IN OCTOBER
Look for: Feature Reports on Process Safety; and Pressure Measurement; A
Focus on Personal Protective Equipment; A Facts at Your Fingertips column
on Seals and Gaskets; News articles on Industry-Academic Partnerships; and
Filtration; and more
Cover: David Whitcher
ONLY ON
CHEMENGONLINE.COM
Look for Web-exclusive articles;
Test your Knowledge
quizzes; New Products;
Latest News; and more
33
36
41
TRANSFER HEAT,
NOT BLAME.
In your line of work, you cant afford downtime. You have to know that
everything is doing its job so you can actually do yours. Thats why, at Eastman,
we have you covered with a wide range of dependable Therminol heat transfer
fuids for some of the worlds most technical applications. And with our
Total Lifecycle Care

Program, you can count on dedicated support

throughout the systems lifecycle. To learn more, go to Therminol.com or
call 1-800-426-2463 in North America. In Europe, call 32.2.746.5134.
2014 Eastman Chemical Company or its subsidiaries. All rights reserved. As used herein, denotes registered trademark status in the U.S. only.
Circle 20 on p. 76 or go to adlinks.che.com/50980-20
UnitedRentals.com/Futures | 800.UR.RENTS
2014 United Rentals, Inc.
#URBuildingFutures
From commercial construction to industrial operations
and public projects, the United Rentals team
is proud to provide our customers the best equipment,
tools and solutions in the industry.
Aerial | Earthmoving | Power & HVAC | Trench Safety | Tools | Technology
Circle 48 on p. 76 or go to adlinks.che.com/50980-48
Editors Page
I
t seems that more and more, security concerns both physical and
cyber have become part of our daily lives both off and on the job.
The all-too-frequent news stories on the topic as well as repetitive
prompts, such as the if you see something, say something slogan,
remind us to keep up our vigilance. This past year, security has been
the subject of more than one Executive order that has resulted in
stepped-up activity across numerous U.S. Government agencies.
In February, the National Institute of Standards and Technology
(NIST; Gaithersburg, Md., www.nist.gov) unveiled its Cybersecurity
Framework, which was developed in response to Executive Order
13636, titled Improving Critical Infrastructure Cybersecurity, that
was signed by President Obama one year earlier. The Framework
was developed through a collaborative effort between industry and
the government, and it gives guidance to owners and operators of
critical infrastructure of which the chemical process industries
(CPI) are part on how to manage cybersecurity-related risks. A
description of the Framework and other cybersecurity-related re-
sources relevant to the CPI can be found in our June issue (ICS Se-
curity: The Owner-Operators Challenge, Chem. Eng., pp. 3035).
Executive Order 13650, Improving Chemical Facility Safety and
Security, was signed by the President in August 2013. The response
to this order was the subject of much discussion at the recent Chemi-
cal Sector Security Summit (July 2224, Baltimore, Md.; www.dhs.
gov/2014-chemical-security-summit), now in its eighth year. An in-
teragency working group released a report to the President titled
Actions to Improve Chemical Safety and Security A Shared Com-
mitment, in June. This report outlines action plans in response to
the Executive order in five areas: Strengthening community plan-
ning and preparedness; enhancing Federal operational coordination;
improving data management; modernizing policies and regulations;
and incorporating stakeholder feedback and developing best prac-
tices. Presenters at the Security Summit commented that one of the
more important outcomes of the Executive order is that a number of
government agencies are now cooperating and communicating much
more effectively about security in the CPI.
And it seems that CFATS (Chemical Facility Anti-Terrorism Stan-
dards) may finally have the strong support in Congress that could
lead to longterm authorization, instead of the annual process that the
program has undergone for the past seven years since its inception. In
his presentation at the Security Summit, David Wulf, director of the
Infrastructure Security Compliance Division (ISCD), Dept. of Home-
land Security (DHS) called 2014 a transformative year for CFATS as
he outlined the progress made in the program, including the approval
of nearly 1,000 site security plans (for background, see CFATS and
Chemical Plant Security, Chem. Eng., Sept. 2009, pp. 2123).
Worldwide interest in CPI security is also growing.
It was suggested during international sessions at the
Security Summit that U.S. approaches to security,
such as (1) the combination of safety and security,
and (2) public and private partnerships, could offer
guidance to a broader international community.
Much groundwork has been laid and the key
now is to make it a priority to incorporate secu-
rity into our routine endeavors.
Dorothy Lozowski, Editor in Chief
Making security a priority
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 5
Winner of Eight Jesse H. Neal
Awards for Editorial Excellence
Published since 1902
An Access Intelligence Publication
PUBLISHER
MICHAEL GROSSMAN
Vice President and Group Publisher
[email protected]
EDITORS
DOROTHY LOZOWSKI
Editor in Chief
[email protected]
GERALD ONDREY (Frankfurt)
Senior Editor
[email protected]
SCOTT JENKINS
Senior Editor
[email protected]
MARY PAGE BAILEY
Assistant Editor
[email protected]
AUDIENCE
DEVELOPMENT
SARAH GARWOOD
Audience Marketing Director
[email protected]
GEORGE SEVERINE
Fulfillment Manager
[email protected]
JEN FELLING
List Sales, Statlistics (203) 778-8700
[email protected]
ART & DESIGN
DAVID WHITCHER
Art Director/
Editorial Production Manager
[email protected]
PRODUCTION
JOHN BLAYLOCK-COOKE
Ad Production Manager
[email protected]
INFORMATION
SERVICES
CHARLES SANDS
Director of Digital Development
[email protected]
CONTRIBUTING EDITORS
SUZANNE A. SHELLEY
[email protected]
CHARLES BUTCHER (U.K.)
[email protected]
PAUL S. GRAD (Australia)
[email protected]
TETSUO SATOH (Japan)
[email protected]
JOY LEPREE (New Jersey)
[email protected]
GERALD PARKINSON
(California)
[email protected]
HEADQUARTERS
88 Pine Street, 5th Floor, New York, NY 10005, U.S.
Tel: 212-621-4900 Fax: 212-621-4694
EUROPEAN EDITORIAL OFFICES
Zeilweg 44, D-60439 Frankfurt am Main, Germany
Tel: 49-69-9573-8296 Fax: 49-69-5700-2484
CIRCULATION REQUESTS:
Tel: 847-564-9290 Fax: 847-564-9453
Fullfillment Manager; P.O. Box 3588,
Northbrook, IL 60065-3588 email: [email protected]
ADVERTISING REQUESTS: see p. 76
For reprints, licensing and permissions: Wright's Media, 1-877-652-5295,
[email protected]
ACCESS INTELLIGENCE, LLC
DON PAZOUR
Chief Executive Officer
ED PINEDO
Executive Vice President
& Chief Financial Officer
MACY L. FECTO
Exec. Vice President,
Human Resources & Administration
HEATHER FARLEY
Divisional President,
Business Information Group
JENNIFER SCHWARTZ
Senior Vice President & Group Publisher
Aerospace, Energy, Healthcare
DANIEL MCKINNON
Vice President,
Energy and Engineering Events
4 Choke Cherry Road, Second Floor
Rockville, MB 2O85O www.accessintel.com
ROBERT PACIOREK
Senior Vice President,
Chief Information Officer
SYLVIA SIERRA
Senior Vice President,
Customer Acquisition and Retention
MICHAEL KRAUS
VP, Production, Digital Media
& Design
STEVE BARBER
Vice President,
Financial Planning and Internal Audit
GERALD STASKO
Vice President/Corporate Controller
ALISON JOHNS
Vice President, Emedia
EDITORIAL ADVISORY BOARD
JOHN CARSON
Jenike & Johanson, Inc.
DAVID DICKEY
MixTech, Inc.
MUKESH DOBLE
IIT Madras, India
HENRY KISTER
Fluor Corp.
GERHARD KREYSA (retired)
DECHEMA e.V.
RAM RAMACHANDRAN
(Retired) The Linde Group
In memory
It is with great sadness, that we
learned of the passing of Jay Chow-
dhury, who was an editor with
Chemical Engineering magazine for
20 years. Long-time readers of the
magazine, and those that had the pleasure of knowing
and working with Jay, will remember him as one of
the kindest and wisest of human beings.
Gerald Ondrey
Senior Editor, Chemical Engineering
Founder of green chemistry to
receive 2014 Perkin Medal
The Society of Chemical Industry (SCI; London; www.
soci.org) is presenting the 2014 Perkin Medal to John
C. Warner, president and chief technology officer of the
Warner Babcock Institute for Green Chemistry (Wilm-
ington, Mass., www.warnerbabcock.com). The annual
award recognizes outstanding work in applied chemis-
try in the U.S., and commemorates the discovery of the
first synthetic dye by William Henry Perkin in 1856,
who received the first Perkin Medal in 1906.
Warner holds a B.S. in chemistry from the Univer-
sity of Massachusetts at Boston and M.S. and Ph.D.
degrees in organic chemistry from Princeton. After ten
years with Polaroid Corp., Warner joined the Univer-
sity of Massachusetts at Boston, where he started a
green chemistry doctoral program said to be the
first in the world. He went on to develop an efficient
method of synthesis that requires fewer steps and
generates less waste that is known as non-covalent
derivatization (NCD) technology.
In 2004, Warner received the U.S. Presidential
Award for Excellence in Science, Mathematics and En-
gineering Mentorship.
In 2007, Warner and Jim Babcock founded the War-
ner Babcock Institute for Green Chemistry, with a
goal to create commercial technologies of superior per-
formance that are also environmentally friendly.
The award is being presented at a dinner in War-
ners honor in Philadelphia on September 16.
Postscripts, corrections
July 2014, Finding the Balance in Packaging, p. 27.
In the last paragraph on this page, a resin is incor-
rectly identified as Elite EPE. The correct name is
Elite AT, and the sentence should read: As an example,
for liquid, dry and frozen foods, Elite AT resins help
reduce package thickness by up to 25% without sacri-
ficing toughness or machinability.
August 2014, Whos Who, p. 70. The name of the com-
pany affiliation for Thomas Bartolomei was incorrectly
stated as NAEL Corp. The correct name is NAES Corp.
August 2014, Software for the Human Element,
p. 25. The name Steve Elliott from Ventyx was mis-
spelled as Elliot. The correct spelling is Elliott.
The corrected versions for the above full articles can
be found at www.chemengonline.com.
Letters
Hand||ng equ|pment
- Lifting, weighing, blending,
pallet transfer
- Mobile or stationary
- Manual or fully automatic
- Loads up to 2500 kg handled
- Hygienic stainless steel
- GMP-compliant design
- ATEX conformity
M||er GmbH - 79618 Rhe|nfe|den (Germany|
Industr|eweg 5 - Phone: +49(0| 7623/969-0 - Fax: +49(0| 7623/969-69
A company of the M||er group
|nfo@mue||er-gmbh.com - www.mue||er-gmbh.com
For per f ect
p r o d u c t i o n
methods
Circle 46 on p. 76 or go to adlinks.che.com/50980-46
Circle 34 on p. 76 or go to adlinks.che.com/50980-34
6 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
0ulolec j:ovioes e~oi:q lec:ooqies ~:o se:vices
o: le susl~i:~Le use o E~:ls :~lu:~ :esou:ces
/s le qoL~ e~oe: i: :i:e:~s ~:o :el~s j:ocessi:q
lec:ooqy, we ~ve oeveojeo :~:y L:e~l:ouq
lec:ooqies ove: le oec~oes o: ou: cuslo:e:s i:
:el~s ~:o :i:i:q i:ousl:y \e ~so j:ovioe i::ov~live
soulio:s o: i:ousl:i~ w~le: l:e~l:e:l, le ulii.~lio:
o ~le::~live e:e:qy sou:ces ~:o le ce:ic~ i:ousl:y

For lhe whole slory,

pleose visil our
YouTube chonnel.
Circle 36 on p. 76 or go to adlinks.che.com/50980-36
Bioenergy Research: Advances
and Applications. By Vijai K.
Gupta, Maria G. Tuohy, Christian
Kubicek, Jack Saddler and Feng Xu.
Elsevier Inc., 225 Wyman Street,
Waltham, MA 02451. Web: elsevier.
com. 2014. 500 pages. $149.95.

Non-equilibrium Thermody-
namics: Transport and Rate
Processes in Physical, Chemi-
cal and Biological Systems. 3rd
ed. By Yasar Demirel. Elsevier Inc.,
225 Wyman Street, Waltham, MA
02451. Web: elsevier.com. 2014. 786
pages. $249.95.
Black Liquor Gasification. By
Pratima Bagpai. Elsevier Inc.,
225 Wyman Street, Waltham, MA
02451. Web: elsevier.com. 2014. 130
pages. $69.95.
Industrial Wastewater Treat-
ment, Recycling and Reuse. By
Vivek Ranade and Vinay Bhandari,
Butterworth-Heinemann, Elsevier
Inc., 225 Wyman Street, Waltham,
MA 02451. Web: elsevier.com. 2014.
576 pages. $140.00.
Process Modeling and Simula-
tion in Chemical, Biochemical
and Environmental Engineer-
ing. By Ashok Kumar Verma, Tay-
lor and Francis Group LLC, 6000
Broken Sound Parkway NW, Suite
300, Boca Raton, FL 33487. Web:
crcpress.com. 2014. 440 pages.
$139.95.
Formulation of Disperse Sys-
tems: Science and Technology.
By Tharwat F. Tadros. John Wiley
& Sons, Inc., 111 River Street,
Hoboken, NJ 07030, Web: wiley.
com. 2014. 504 pages, $205.00.
Process and Plant Safety. By
Ulrich Hauptmanns, Springer-
Vieweg, Abraham Lincoln Strasse,
46, 65189, Weisbaden, Germany.
Web: springer.com. 2014. 655
pages. $179.00.
Editors note: If you would like to contribute
a book review for the Bookshelf column, please
contact senior editor Scott Jenkins at sjenkins@
chemengonline.com.
Bookshelf
Krytox FIuorinated Lubricants
CaIifornia - IIIinois - Connecticut - Canada
[email protected]
miIIer-stephenson.com/krytox

Greases and OiIs are: Chemically Inert. Insoluble in common

solvents. Thermally stable (-103F to 800F). Nonflammable.
Nontoxic. Oxygen Compatible, Low Vapor Pressure. Low
Outgassing. No Migration - no silicones or hydrocarbons.
Krytox

offers Extreme Pressure, Anticorrosion and Anti-wear

properties. Mil-spec, Aerospace and Food Grades (H-1 and
H-2) available! Widely used in Vacuum and Cleanroom
environments.
We also offer a complete line of inert fluorinated Dry Lubricants
and Release Agents.
For technical information, call 800.992.2424 or 203.743.4447
(8AM - 4PM ET).
DuPont^ Krytox

Channel Partner Since 1991

Simply pull
our chain.
Ductile Iron Clamp-on Chain
Sprocket ts hand wheel sizes
from 2 to 26 inches in diameter
Clamps on to existing hand wheel
for safe, eective manual valve
operation
All units come complete with
sprocket wheel, chain guide,
set collar, zinc plated hardware
and installation instructions
All CL Series wheels are available
in galvanized and stainless steel
When it comes to valve safety and convenience
Call us today toll free:
1. 800 . 477.7686

918.446.3500 [email protected] rotohammer.com
Circle 44 on p. 76 or go to adlinks.che.com/50980-44
Circle 33 on p. 76 or go to adlinks.che.com/50980-33
8 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Thermodynamics and the
Destruction of Resources. Ed-
ited by Bhavik Bakshi, Timothy
Gutowski and Dusan Sekulic,
Cambridge University Press, UPH,
Shaftesbury Road, Cambridge CB2
8BS, U.K., Web: cambridge.org,
2014. 524 pages. $63.00.
Hazardous Area Classification
in Petroleum and Chemical
Plants: A Guide to Mitigating
Risk. By Alireza Bahadori, CRC
Press, Taylor and Francis Group
LLC, 6000 Broken Sound Parkway
NW, Suite 300, Boca Raton, FL
33487. Web: crcpress.com. 2013.
564 pages. $149.95.
IP Standard Test Methods for
Analysis and Testing of Petro-
leum and Related Products,
and British Standard 2000
Parts. By Institute of Petroleum.
Energy Institute, 61 New Caven-
dish Street, London, W1G 7AR,
U.K., Web: energyinst.org. 2014.
electronic book, $800.00.
Lithium-Ion Batteries: Ad-
vances and Applications. By
Gianfranco Pistoia. Elsevier Inc.,
225 Wyman Street, Waltham, MA
02451. Web: elsevier.com. 2014. 660
pages. $235.00.
Chemistry of Fossil Fuels and
Biofuels. By Harold Schobert,
Cambridge University Press, UPH,
Shaftesbury Road, Cambridge CB2
8BS, U.K., Web: cambridge.org,
2013. 497 pages. $118.00.
Advanced Materials Science
and Engineering of Carbon. By
Michio Inagaki, Feiyu Kang, Masa-
hiro Toyoda and Hidetake Konno,
Elsevier Inc., 225 Wyman Street,
Waltham, MA 02451. Web: elsevier.
com. 2014. 440 pages. $149.95.
Plant Equipment & Mainte-
nance Engineering Handbook.
By Duncan Richardson. McGraw-
Hill Professional Publishing, 1221
Avenue of the Americas, 28th Floor,
New York, NY 10020. Web: mcgraw-
hill.com. 2014. 592 pages. $150.00.
Scott Jenkins
5M 1PlNk
A 90%
LA5
lN N6
u5 WlLL
LMMl5
1Pu6Pu1.
W 1PlNk
lIIN1.
Ar 8L0MLR we have a repurarlon for maklng rhlngs a llrrle
dlnerenr. 1ake rhe srrerch-lm paller packaglng sysrem,
8L0MLR srrerch hood. ln a secror where energy-lnrenslve
shrlnk hoodlng ls srlll common, 8L0MLR srrerch hood uses
a non-rhermal srrerch-lm sysrem. 1he resulr: berrer load
srablllry, hlgher rhroughpur, up ro J rlmes less lm consump-
rlon and 9% energy savlngs. All rhls makes a blg dlnerence
ro producrlvlry - and ro rhe envlronmenr.
For more information, visit www.beumergroup.com
Visit us!
owtech, Nuremberg, 6ermany
September 30 - 0ctober 2, 2014
PaII 1, stand 13S
Visit us!
Macropak, Utrecht, 1he NetherIands
September 30 - 0ctober 3, 2014
PaII 1, stand 8120
Circle 11 on p. 76 or go to adlinks.che.com/50980-11
Ross mixers and blenders
are engineered to run
trouble-free for decades. But
if you ever need a replacement
part, chances are we have it
right here, ready to ship in
48 hours or less.
We keep a multi-million dollar
inventory of parts in stock
from planetary gears to
rotors, stators, seals and
O-rings for your High Shear
Mixer. So, when you need
help to keep your production
on track, you can count on us.
Learn more about the value
built into every Ross mixer and
blender. Visit www.mixers.com.
Or call 1-800-243-ROSS.
Jon Kerr
Parts Manager
Ross Employee Owner
Jon Kerr
Parts Manager
Ross Employee Owner
Scan to learn more.
Free Tag Reader: http://gettag.mobi
Need a new gear
for your 1967
HDM Double
Planetary Mixer?
No problem.
Circle 43 on p. 76 or go to adlinks.che.com/50980-43
T
he first commercial contract delivery
was recently made for an emissions
control product that removes mercury
from fluegas without the use of acti-
vated carbon. The product, known as
AS-HgX, is made by Novinda Corp.
(Denver, Colo.; www.novinda.com), and
will be used in the utility power-gener-
ation industry to help users meet limits
on mercury emissions.
The product is a departure from the
use of activated carbon to adsorb mer-
cury from fluegas, as is done with con-
ventional technology, and offers a host of
advantages over the current approach.
In power plants where activated carbon
is used to remove mercury, the activated
carbon often contaminates the flyash,
rendering it useless as a replacement for
ordinary Portland cement. Using flyash
in concrete can reduce carbon emissions
considerably and save significant money,
notes Jim Butz, vice president of product
management at Novinda. Butz further
explains that a cradle-to-grave analysis
of AS-HgX (manufacturing, transport,
and so on) shows that its carbon footprint
is one-tenth that of activated carbon. An-
other advantage of the product over acti-
vated carbon is its inertness. It does not
present flammability and explosion risks,
as activated carbon does.
Starting with an aluminosilicate clay,
Novinda has developed a patented for-
mula that infuses a proprietary metal
Mercury removal with modified aluminosilicate clay
E
deniq Inc. (Visalia, Calif.;
www.edeniq.com) an-
nounced progress in building
demonstration facilities in
Brazil and China that feature
the companys proprietary
process for converting cellu-
losic biomass into industrial
sugar for fermentation or cat-
alytic conversion (diagram).
In Brazils So Paulo state,
Edeniq is partnering with
Usina Vale to build a 10-ton/d
demonstration plant that will
bolt onto an existing sugar-
cane-to-bioethanol production
facility, allowing it to increase etha-
nol production by utilizing waste bio-
mass. Meanwhile, in Jilin province,
China, Edeniq is partnering with
Global Bio-chem Group (Hong Kong,
China) to build a commercial demon-
stration facility that will eventually
produce 50,000 metric tons (m.t.) per
year of sugar from corn stover at an
attractive transfer price, the com-
pany says.
Both facilities feature Edeniqs pat-
ented continuous biomass-pretreat-
ment technology, which hydrates the
biomass, and mechanically grinds and
mills the material. They also feature
a closely integrated continuous sac-
charification process that depends on
a proprietary reactor design to reduce
residence times and increase enzyme-
hydrolysis efficiency.
Among three types of mechanical
shearing equipment deployed in the
process, Edeniqs pre-treatment step
features the Cellunator, which pro-
duces a homogenous, high-density
slurry of biomass solids, while reduc-
ing average particle size to the sev-
eral-hundred-micron range, explains
Tom Griffin, chief technology officer
at Edeniq. The comprehensive shear-
ing and homogenization action gives
enzymes enhanced access to biomass
particles, which allows higher con-
version rates to fermentable sugars.
Further, the use of mechanical shear-
ing obviates the need for high
temperatures and corrosive
chemicals in the pretreat-
ment stage, he adds.
Edeniq has also developed
a unique solid-liquid separa-
tion process that generates a
solids-free sugar solution as a
product, which is continually
removed. The enzymes, addi-
tives and unreacted substrate
are continuously recycled in
the process. The separation
step features a high-through-
put tangential-flow filtration
(TFF) system that has been
customized for biomass. The Edeniq
process also includes a step in which
solid lignin is captured as a co-prod-
uct; it can be used as a fuel to heat pro-
cess boilers, or further developed into
a livestock feed component.
Edeniq currently operates pilot
facilities at its California headquar-
ters and an Omaha, Neb. based busi-
ness unit that utilizes the companys
technology to enhance ethanol yields
from corn. The Brazil plant has begun
qualification testing of preprocessing
unit operations, with construction
completion planned for late 2014. The
China plant will be constructed in
late 2014, with Edeniq enhancements
integrated in stages through 2015.
Note: For more information, circle the 3-digit number
on p. 76, or use the website designation.
Edited by Gerald Ondrey September 2014
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 11
CO
2
-to-syngas . . .
Scientists from the Univer-
sity of Illinois at Chicago
( www.uic.edu) have de-
veloped a catalytic system
molybdenum disulfde
and an ionic liquid to
convert CO
2
into synthesis
gas, (syngas; a mixture
of CO and H
2
that is used
for making liquid fuels and
chemicals, such as metha-
nol). Unlike alternative CO
2
-
reduction processes, which
only generate CO, the new
catalyst system enables
the production of syngas
directly. The catalyst is also
said to be less expensive
(Continues on p. 12)
(Continues on p. 12)
Demonstration plants for biomass-to-sugar technology under construction
A
D
C
B
A. Pre-processing B. Pre-treatment C. Saccharifcation
D. Separations and product recovery
CHEMENTATOR
C
rystal Solar Inc. (Santa Clara, Calif.;
www.xstalsolar.com) is preparing for
high-volume production of silicon wa-
fers using a process that forms the wa-
fers directly from trichlorosilane (TCS)
gas using a chemical vapor deposition
(CVD) epitaxy process that can signifi-
cantly lower the manufacturing costs
for solar photovoltaic cells.
By eliminating several steps used
in the traditional solar-wafer manu-
facturing process, including melting
down polysilicon pieces, formation of
a monocrystalline silicon ingot and
slicing the wafers, Crystal Solars Di-
rect-to-Wafer technology allows for a
50% reduction in the wafers produc-
tion cost, which represents almost
half of the cost of the final solar cell.
Epitaxy has been well known for
silicon production in the past, says
T.S. Ravi, Crystal Solar co-founder
and CEO, but the approach has not
been economical for use in solar cell
applications because growing the
silicon layer has been too slow, and
conversion rates from TCS to solid Si
have been too low. The key for us was
to find good solutions to the problems
of how can you grow the wafers faster
and how can you achieve higher con-
version rates? Ravi says.
By using a vertical reactor concept,
the company has been able to achieve
40% conversion rates of TCS to silicon,
with the ability to make several hun-
dred wafers at a time at atmospheric
pressure. The reactor combines solar-
grade TCS gas with hydrogen to de-
posit monocrystalline silicon on top of
a porous silicon release layer.
Capital costs associated with this
production method are said to be half
what is required for traditional poly-
silicon plants. Another advantage of
the Crystal Solar method is its amena-
bility toward automation, Ravi notes.
The technology was developed in part
as a component of a National Renew-
able Energy Laboratory (Golden, Colo.;
www.nrel.gov) program, and has gar-
nered an R&D 100 award in 2014.
Crystal Solar has been making wa-
fers in a pilot phase, and generating
positive feedback in tests with cell man-
ufacturers, Ravi says, and the company
is gearing up to add capacity now.
This process realizes large costs savings for manufacturing silicon wafers
than alternative reduction
catalysts that are based on
gold or silver. The results are
described in the July 30 issue
of Nature Communications.
. . . and CO
2
-to-methanol
Meanwhile, a new catalytic
system that directly converts
CO
2
into methanol has been
developed by scientists at
the U.S. Dept. of Energys
Brookhaven National Labora-
tory (Upton, N.Y.; www.bnl.
gov), in collaboration with re-
searchers from the University
of Seville (Spain; www.us.es)
and the Central University of
Venezuela (Caracas; www.
ucv.ve). The catalyst is com-
posed of copper and cerium
oxide (ceria) nanoparticles.
The research team found
that the interface of the two
types of nanoparticles is
critical to the reactivity of the
catalyst system. Laboratory
studies showed that the cata-
lyst converts CO
2
to methanol
more than 1,000 times faster
than plain copper particles,
and almost 90 times faster
than a common copper/zinc-
oxide catalyst currently used
industrially. The results are de-
scribed in the August 1, 2014
issue of Science.
(Continued from p. 11)
sulfide material into the clay particles.
After blending and milling processes,
the AS-HgX product can be injected
into fluegas streams, where it reacts
with mercury to form mercuric sulfide,
a very stable and insoluble compound,
notes Butz. By altering the structure of
the metal sulfide and the manufacturing
process, Novinda can make related prod-
ucts using the same product platform.
Novinda has partnered with several
manufacturers of injection systems that
work well because the dispersal of the
material in the fluegas is a key factor in
the products effectiveness.
Novindas product has been tested in
full-scale coal power plants burning sev-
eral types of coal in various locations, and
has shown the ability to remove over 90%
of mercury present in plant fluegas, Butz
says. He adds that the tests suggested
that AS-HgX is particularly effective in
plants that use dry scrubbing to remove
SO
2
. In the future, AS-HgX may also be
applied for mercury removal in fluegas
from industrial boilers and cement kilns.
MERCURY REMOVAL (Continued from p. 11)
12 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
This portable device measures Hg
+2
in water samples
A
n ultra-sensitive, low-cost and portable
system for detecting mercury in water
has been developed by University of Ad-
elaide (Australia; www.adelaide.edu.au)
researchers, in collaboration with the
Universitat Rovira i Virgili (Tarragona,
Catalonia, Spain; www.urv.cat).
Project leader Abel Santos, of the Ad-
elaides School of Chemical Engineering,
says there are systems capable of monitor-
ing mercury at trace levels, but they are
huge, expensive machines and are compli-
cated to use. Also, samples require chemi-
cal treatment before analysis in such in-
struments. Our system, on the other hand,
is very cost-competitive, only as big as a
mobile phone and easy to use, he says.
The researchers have engineered a nano-
porous material, called nanoporous anodic
alumina, to make a special structure called
a rugate filter. The surface of the filter has
been modified to make it selective to mer-
cury ions. As water flows through the pores,
the mercury ions become attached to the
surface. Reflection spectroscopy measures
the amount of mercury present.
The system has a linear working range
from 1 to 100 M of Hg
+2
. Its low limit
of detection is 1 M of Hg
+2
ions. Tests
were successfully carried out at the River
Torrens, demonstrating the suitability of
the system for developing environmental
point-of-analysis systems. The system
also proved to be highly selective in a
complex mixture of other metals and en-
vironmental samples.
www. berndorf -usa. com
Berndorf Belt Technology
59 Prairie Parkway
Gilberts, IL 60136
Phone: (+1)847-841-3300
Fax: (+1)847-931-5299
[email protected]
Detailed consultation in pre-
liminary stages of production
ensures that steel belts
from Berndorf Band meet all
requirements set by the customer,
e.g.

excellent mechanical,
physical and geometric
properties

high corrosion resistance,
even in extremely
aggressive atmosphere

perfect adhesion of
vee-ropes

Berndorf Band offers customized
steel belts for each application
Circle 10 on p. 76 or go to adlinks.che.com/50980-10
J
X Nippon Oil & Energy Corp. (JX_
NOE; Tokyo, Japan; www.noe.jx-group.
co.jp) plans to construct the first com-
mercial plant to utilize its high-severity
fluid catalytic cracking (HS-FCC) tech-
nology, which has been demonstrated to
generate higher ethylene and propylene
yields compared to conventional FCC
technology. The new plant, which could
start operating as early as 2018 at the
companys Kashima Refinery, will have
a processing capacity of 24,000 bbl/d of
crude oil, which is eight times larger
than the semi-commercial demonstra-
tion plant JX_NOE has operated at its
Mizushima Refinery since April 2011
(Chem. Eng., August 2013, p. 10), and
is equivalent to an ethylene capacity
of 300,000 ton/d. JX_NOE will invest
around $5001,000 million for the proj-
ect, which includes the construction of
both the HS-FCC plant and the associ-
ated olefin-conversion unit.
JX_NOE currently supplies 1 million
ton/yr of propylene to the petrochemical
market, and aims to become the leading
propylene supplier in Asia by boosting
this to 1.8-million ton/yr, with 300,000
ton/yr from the new HS-FCC plant and
the remaining 400,000500,000 ton/yr
from production plants outside Japan.
The company believes the HS-FCC tech-
nology will help strengthen its petro-
chemicals production capacity.
The HS-FCC process features a down-
flow reactor that has the advantage of
suppressing backmixing, and also results
in shorter contact times (0.50.6 s) be-
tween the feed and the catalyst, which
allows higher catalyst-to-oil ratios. The
short contact times also enable the pro-
cess to operate at higher (600C) temper-
atures (For more process information, see
Chem. Eng., August 2009, p. 12).
Commercial debut planned for an FCC process
with enhanced olefins production
CHEMENTATOR
14 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
A History Steeped in Innovation.
Cashco, Inc.
P.O. Box 6, Ellsworth, KS 67439-0006 | Ph. (785) 472-4461, Fax: (785) 472-3539 | www.cashco.com
The industry
turns to Cashco
when it absolutely counts.
CELEBRATI NG 100 YEARS
When quality counts . . . choose Cashco. For 100 years,
the industry has turned to Cashco for precision control
solutions. The Ranger QCT is a universal control valve. It
offers versatility, adaptability and ease of maintenance in
almost any application. The Ranger is designed for use in
steam, chemical, gas and cryogenic liquid applications.
Broad product lines provide solutions
for virtually any project.
Superior quality product surpassed only
by the service and support.
Strategically located Service Centers
with factory-trained specialists.
Dont wait any longer to partner with
the industrys leader in process control.
Call us today.
Ranger QCT
Circle 15 on p. 76 or go to adlinks.che.com/50980-15
TSA for CCS advances
Last month, a post-combustion
process capable of separating
CO
2
from fuegas at one-third
the cost of alternative separa-
tion processes moved a step
closer to commercialization,
as Inventys Thermal Tech-
nologies, Inc. (Burnaby, B.C.,
Canada; www.inventysinc.com)
received additional funding
from major investors, including
Chevron Technology Ventures
LLC, the venture-capital arm
of Chevron Corp. (San Ramon,
Calif.; www.chevron.com),
and Chrysalix Energy Venture
Capital. Inventys will use the
additional fnancing to expand
manufacturing and enable the
deployment of full-scale sys-
tems using its VeloxoTherm
gas-separation technology in
late 2016. VeloxoTherm is based
on a proprietary, low-pressure
temperature-swing adsorption
(TSA) technology that is said
to achieve a carbon-capture
cost of $15/m.t. one third the
cost of current post-combustion
methods. (For more details
about VeloxTherm, see Chem.
Eng., January 2011, p. 9).
(Continues on p. 18)
We create
chemistry
that lets
individual
needs love
global
innovation.
As the global leader in catalysis, BASF draws on the
talent and expertise of more than 1,100 researchers
working in close partnership with our customers. This
collaboration results in innovations that drive new
levels of performance and achievement, today and
over the long term. When global catalyst innovations
help our customers become more successful, its
because at BASF, we create chemistry.
www.catalysts.basf.com
Circle 9 on p. 76 or go to adlinks.che.com/50980-09
Kenics

UltraTab Static Mixer

Achieve a High Degree of Mixing in a Compact Space
In turbulent ow mixing/blending applications, the Kenics UltraTab provides
complete blending in short distances and low pressure drop through the element.
Available in various materials including Stainless Steel and FRP.
The patent pending UltraTab is optimized for your applications, such as:
For additional information, visit www.chemineer.com/kenics.
For sales, call 1-800-643-0641 or go to
www.chemineer.com/sales
pH adjustment
Chemical injecting
Acid dilution
Mixing occulation agents
Coagulation processes
Sodium Hypochlorite
Chlorination/dechlorination
www.chemineer.com
Circle 16 on p. 76 or go to adlinks.che.com/50980-16
L
ast June, Showa Denko K.K. (SDK;
Tokyo, Japan; www.sdk.co.jp)
started commercial operation of its
new 100,000-ton/yr ethyl acetate
plant at Oita Complex. The new
plant is the first commercial facil-
ity in Japan to use the companys
proprietary production-process tech-
nology. The process technology was
first demonstrated in a 60,000-ton/yr
plant in Indonesia.
SDK formerly produced ethyl ac-
etate by a two-step process in which
acetaldehyde is first made from eth-
ylene, and then converted to ethyl
acetate. In the new process, imported
acetic acid is used as a feedstock, and
reacts directly with ethylene using a
solid heteropolyacid catalyst, which
SDK developed in collaboration with
professor Toshio Okuhara at Hok-
kaido University and Emeritus pro-
fessor Makoto Misono at the Univer-
sity of Tokyo.
Ethyl acetate is an organic solvent
used in a wide range of applications,
including printing ink, paint, and ad-
hesives for electronic devices. While
global demand for the product is ex-
pected to continue growing, its busi-
ness environment continues to be
difficult due to the rise in raw mate-
rial and fuel costs, and the increase
in imports of inexpensive products
that are mainly produced in China
via a fermentation process.
A more direct route to ethyl acetate
CHEMENTATOR
16 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
A
sludge-optimization technology
for municipal water-treatment
facilities is poised for rapid growth
after the exclusive worldwide patent-
licensing rights for the technology
were acquired by CNP Technology
Water and Biosolids Corp. (Kenosha,
Wisc.; www.cnp-tec.com).
The technology, known as AirPrex,
was initially developed at Berlin
Water Works (Germany) in 2004, and
was initially licensed to the German
company PCS GmbH. AirPrex was
subsequently implemented at three
sites (two in Germany and one in the
Netherlands from 2007 to 2012). Now,
with the license transferred to CNP,
orders to install the technology have
been made for the Amsterdam West
water-treatment plant in the Nether-
lands, as well as plants in Salzgitter
and Uelzen, Germany. Several other
projects are in the works in South Af-
rica and in the U.S.
AirPrex uses a reactor with an aera-
tion system to recover the high-phos-
phorus mineral struvite from sludge,
thus avoiding the struvite precipita-
tion that becomes a major mainte-
nance nuisance for water-treatment
Municipal water sludge-optimization technology poised for growth
PLASTIC CONTROL VALVES FOR
ALL YOUR CORROSIVE APPLICATIONS
P.O. Box 938 Angleton, TX 77516
Tel. (979) 849-8266 www.collinsinst.com
Collins plastic control valves are
highly responsive control valves
designed for use with corrosive
media and/or corrosive atmos-
pheres.
Collins valves feature all-plastic
construction with bodies in PVDF,
PP, PVC and Halar in various body
styles from 1/2" - 2" with Globe,
Angle or Corner configurations and
many trim sizes and materials.
Valves may be furnished without
positioner for ON-OFF applications.
Call for more information on our
plastic control valves.
Circle 17 on p. 76 or go to adlinks.che.com/50980-17
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 17
equipment. The technology simulta-
neously recovers a high-phosphorus
byproduct that can be sold for use as
slow-release fertilizer.
A key feature of AirPrex is that
the struvite recovery for plants using
biological phosphorus removal occurs
after the anaerobic digestion of the
biosolids, but before the dewatering
step. This allows a reduction of energy
and chemical additives, says Gerhard
Forstner, president of CNP. In addition
to eliminating the struvite buildup on
process equipment, the removal of the
mineral improves the efficiency of the
sludge dewatering process. When pres-
ent, struvite inhibits dewatering, lead-
ing to wetter cake solids and higher
polymer consumption. Airprex realizes
up to a five-percentage-point increase
in dry solids in the cake, Forstner says,
as well as lowering polymer consump-
tion by up to 30% and reducing phos-
phorus-recycling load by up to 90%
(For more on P-recovery, see Chem.
Eng., February 2013, pp. 1722).
CNP is offering AirPrex as a technol-
ogy provider, with the installation car-
ried out by contractors. Forstner says
the company works with engineering
consultants to provide customized
wastewater treatment systems that
offer the best return on investment.
Monitoring pipeline deposits in realtime
T
he presence of scale depositions
in pipelines can restrict flow, limit
heat transfer and decrease efficiency.
The ability to monitor pipelines for
depositions helps avoid issues and
optimize costs. The Deposition Watch
system from Flowrox Inc. (Linthicum,
Md; www.flowrox.us) presents a real-
time, online predictive-monitoring
solution for detecting scale-related
issues in process pipelines that is
based on the principles of electrical
capacitance tomography (ECT; For
more on ECT, see Chem. Eng., Octo-
ber 1995, pp. 3033).
ECT imaging techniques apply
measured excitation signals to mate-
rials and monitor the output signals.
Through an iterative mathematical
model, these signals reveal informa-
tion about the electrical properties
of the measured material. The Depo-
sition Watch system measures pipe
volume and determines the electri-
cal properties, including permittivity
distribution and conductivity, of the
process fluid and the unwanted depo-
sition. Comparison of these materials
different electrical properties provides
physical information about the behav-
ior of the materials inside the pipe. For
instance, estimated permittivity val-
ues shed light on deposition thickness
and its distribution along pipe walls.
Also, it is possible to evaluate depo-
sition growth rate and available free
pipe-volume percentage, allowing en-
gineers to predict when maintenance
or intervention will be required.
Oteks NTM series includes an automatic tri-color bargraph with even intensity
at both high and low end of the 4-20mA range. New LED technology allows
you to see the status of your process clearly. The NTM series includes:
Brighten Your Control Room
- l9 Dlnerent Models ln Plastlc or Metal Houslng
- Loop, Slgnal or Lxternally Powered Unlts
- |nput Pallure Detectlon and |ndlcatlon vla Serlal |/O
- |mproved Pesponse Tlme
- Plexlble Plrmware for More Customlzatlon Optlons
- Avallable ln up to 4 Channels
Models Pictured: (left) NTM-9 and (right) NTM-X
To learn more about OTLK's NTM Serles,
please vlslt: www.otekcorp.com or call (520)748-7900
Circle 35 on p. 76 or go to adlinks.che.com/50980-35
A
microfluidic, paper-based analyti-
cal device (PAD) in conjunction
with confirmation by a lab-on-a-chip
analysis was developed for detec-
tion of three explosives (trinitro aro-
matics) by a team from the University
of Technology Sydney (Sydney, Aus-
tralia; www.uts.edu.au), the Univer-
sity of Lausanne (Switzerland; www.
unil.ch), and Florida International
University (Miami; www.fiu.edu).
A wide range of analytical tech-
niques have been developed for ex-
plosives detection, some of them of-
fering high sensitivity and selectivity.
However, their long analysis times,
high costs and bulky instrumenta-
tion limit their use in strategic loca-
tions, such as airports or entrances to
chemical and other secure facilities.
Important advantages of PADs are
low cost, easy storage and disposal,
and no requirements for pumps.
The fabrication of PADs involves
the construction of patterns of hydro-
phobic barriers on filter paper, using
techniques such as photolithography,
plotting, paper cutting, plasma oxida-
tion, inkjet printing and laser treat-
ment. The barriers allow controlled
fluid movement that segregates
chemical reactions. In the case of
this particular application, the PAD
works by monitoring a color change
as the nitro compounds react with a
strong base. Color development fol-
lowing exposure of the base to trinitro
explosives is observed immediately,
but is measured after 10 min to en-
sure completion of the reaction.
The limits of detection of trini-
trotoluene (TNT), trinitrobenzene
(TNB) and trinitrophenylmethylnit-
ramine (tetryl) on the PAD were
determined after application of 0.5
L of each explosive at concentra-
tions ranging from 1 to 200 ppm onto
the active device, both visually and
using a video spectral comparator
(VSC6000) at 480-nm wavelength.
The minimum levels detected visu-
ally (and with the VSC6000) were 30
3 ng (7.5 1.0 ng) for TNB, 50
4 ng (12.5 2.0 ng) for TNT and 70
2ng (15.0 2.0 ng) for tetryl. The
technology can also be used for de-
tecting black powder, smokeless pow-
der and fertilizer-based explosives,
such as ammonium nitrate.
An inexpensive, sensitive device for detecting explosives
CHEMENTATOR
18 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
At the Mizushima Refinery 3,000-
bbl/d demonstration plant, propylene
yields have been found to be enhanced
by 25 wt.% much higher than the
4 wt.% yield achieved in the existing
FCC unit. The butenes yield was also
enhanced by 6% to 20 wt.%. Although
the gasoline yield is reduced by 60% to
29 wt.%, the yield of high-octane gaso-
line is increased, says the company.
FCC PROCESS (Continued from p. 14)
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 19
Newsfront
T
he chemical process industries
(CPI) have experienced many
benefits from the so-called
shale-gas boom recent years
have seen an unprecedented rise in
construction and expansion activity
in the petrochemicals sector. Shown
in Figure 1 is construction at the
Freeport, Tex. facility of The Dow
Chemical Company (Dow; Midland,
Mich.; www.dow.com). Dow is just
one of many companies to initiate
large petrochemical projects on the
U.S. Gulf Coast in the wake of in-
creased shale-gas availability.
We are in the midst of unprece-
dented growth due to the abundance
of natural gas liquids, explains Bob
Maughon, Dows global R&D direc-
tor for performance plastics and
feedstocks. The use of natural-gas
liquids took hold in 2009. In 2011
and 2012, the abundance of eth-
ane compelled the industry to flex
strongly toward natural-gas feed-
stocks and away from petroleum-
derived naphtha.
Since this shift, though, the
changing feedstock landscape in pe-
troleum refineries has led to short-
ages for many co-products, including
1,3-butadiene (butadiene; Figure
2), an important building block for
synthetic rubber and nylon. Says
Maughon: As naphtha cracking
has waned and ethane cracking
increases, cracker co-product pro-
duction drops. The slate of products
that have been affected include pro-
pylene, butadiene, isoprene, ben-
zene and others. It isnt that the
industry doesnt want to produce
these chemicals. The economics of
ethane-only cracking have become
so compelling that naphtha crack-
ing has been squeezed. Production
is driven to the lighter feedstocks
and co-product production is lost.
Figure 3 shows the variation in
production from naphtha-cracking
operations versus the cracking of
lighter feedstocks. The shale-gas-
imposed scarcity for chemicals like
butadiene presents opportunities
for new technologies to arise. This
article covers some actions that
companies are taking in response
to butadiene shortages, includ-
ing the development of on-purpose
production methods and the use of
bio-based feedstocks.
Oxidative dehydrogenation
TPC Group Inc. (Houston; www.tp-
cgrp.com), has been commercially op-
erating its OXO-D butadiene process
technology for over 40 years. TPCs
OXO-D technology converts buty-
lenes into butadiene through oxida-
tive dehydrogenation. In June 2014,
TPC announced a partnership with
Honeywells UOP LLC (Des Plains,
Ill.; www.uop.com) to further develop
and globally license this technology
in the wake of increased demand for
on-purpose butadiene. There will be
research and development teams
and pilot plants at both companies
facilities to jointly develop process
advancements. Also, through this
agreement, UOP acquires the world-
wide exclusive licensing rights of the
TPC OXO-D process.
Jim Rekoske, petrochemicals
global business director for UOP,
describes what attracted UOP to
this partnership, saying A key dis-
tinguishing feature of the OXO-D
process is the more than 40 years of
operating experience. This operat-
ing experience allows TPC and UOP
to understand and position on-pur-
pose butadiene technology for our
licensing customers. Rekoske goes
on to emphasize that timing is key
for this collaboration, stating that
This is not a technology that needs
a long development period or a long
market incubation period the op-
portunities are now.
Both companies stress the impor-
tance of on-purpose butadiene pro-
duction going forward demand
for butadiene-based products, such
as tires, is rising, as traditional
feedstocks are becoming less read-
ily available. Lighter feedstock
slate means, on average, fewer ki-
lograms of butadiene produced per
metric ton of ethylene produced.
On-purpose butadiene technolo-
gies will be needed to fill this gap,
explains Rekoske.
With the ongoing flurry of ac-
tivities in the shale-gas sector, TPC
Group sees global potential for the
licensing of the OXO-D process.
Miguel Desdin, senior vice presi-
dent and chief financial officer of
Newsfront
Butadiene scarcity imposed by the shift toward
ethane cracking provides opportunities for the
development of new technologies
THE FUTURE OF BUTADIENE
FIGURE 1. New construction (like that
at Dows Freeport complex) is rampant as
the industry takes advantage of the shale-
gas boom
H H
H
H
C
C
C
C
H
H
FIGURE 2. 1,3-butadiene is a major co-
product from naphtha cracking, and is ex-
periencing shortages due to the newfound
dependence on lighter refning feedstocks
The Dow Chemical Company
20 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront
TPC Group states that The global
market will need on-purpose buta-
diene to meet future demand, and
in order to satisfy that demand,
multiple on-purpose butadiene
plants in various regions of the
world will be required. Desdin goes
on to say, Since the announcement,
there has been a significant amount
of interest in the technology. UOP is
currently in the process of creating
a licensing package for the OXO-D
technology, which will be avail-
able to prospective licensees in the
fourth quarter of 2014.
In the earlier stages of develop-
ment is another technology partner-
ship focused on butadiene, also an-
nounced in June 2014, by The Linde
Group (Pullach, Germany; www.
linde.com) and BASF SE (Ludwig-
shafen, Germany; www.basf.com).
The two companies are collaborat-
ing on the development and licens-
ing of an on-purpose route from
butane to butadiene via butenes.
For butene synthesis from butane,
BASF is contributing a high-yield
monolithic catalyst. In the pres-
ence of a metal-oxide catalyst, those
butenes are then subsequently con-
verted via an oxydehydrogenation
step into butadiene. Although the
process is still quite new, progress to
commercialization is moving ahead,
with developments occurring at both
kilogram-scale and pilot-plant-scale
operations in Ludwigshafen (Chem.
Eng., July 2014, p. 14).
Last year, Wison Engineering Ltd.
(Shanghai; www.wison.com) intro-
duced its own on-purpose butadiene
technique, also based on oxidative
dehydrogenation principles (Chem.
Eng., June 2013, p. 15). With a pro-
prietary high-yield catalyst in its
arsenal and a process-design pack-
age completed, Wison expects to
announce a license agreement for
commercial deployment of the tech-
nology in the coming months.
Another on-purpose technol-
ogy developed in response to the
prevalence of lighter cracking
feedstocks and the associated re-
duction in butadiene supply is the
butene-to-crude-butadiene process
(abbreviated BTcB), which was
introduced by Mitsubishi Chemi-
cal Corp. (MCC; Tokyo, Japan;
www.m-kagaku.co.jp) at the 2014
American Institute of Chemical
Engineers (AIChE) Spring Meet-
ing. The BTcB process (Figure 4)
involves the oxidative dehydroge-
nation of a C4 mixture to produce
1,3-butadiene in the presence of air,
steam and a very selective catalyst.
Yields are estimated to be 1025%
higher than past butadiene-produc-
tion technologies, per MCCs evalu-
ations. Also, the catalyst achieves
a very long operational life with-
out the need for regeneration, says
the company. The reaction runs at
ambient pressure, and operating
temperatures are typically between
300 and 400C. MCC also estimates
that this process involves up to 80%
less wastewater than past butadi-
ene technologies, decreasing the en-
vironmental impact of operations.
The process is flexible enough
that all industrial C4 mixtures, in-
Fuel oil
Toluene
Benzene
Pygas
C5
Other C4
Butadiene
Butadiene
CH
4
/H
2
/lights
CH
4
/H
2
Propylene
Propylene
Ethylene
Ethylene
~3
1
/4 lb/lb C2=
~1
1
/4 lb/lb C2=
~30%
~80%
~15%
~5%
Naphtha Ethane
FIGURE 3. A comparison
of the products of naphtha
cracking versus ethane
cracking with the same amount of ethylene
production illustrates that some co-products
of naphtha cracking are lost with the shift
towards the use of lighter feedstocks
The Dow Chemical Company
DUNN HEAT
EXCHANGERS, INC.
D
U
N
N
H
E
AT EXCHANG
E
R
S

I
N
C
w
w
w
.dunnheat. co
m









Q
uality Service Since 1968
Contact us:
[email protected]
for more information
409-948-1704
281-337-1222
Dunns specialized facility offers complete
services for shell and tube type heat ex-
changers and related process equipment.
24 hours a day 7 days a week
www.d0ooheat.com 410 21st St. So0th Texas 0|ty, TX 77590
CLEANING
REPAIR/RETUBING
DECOMMISSIONING
FABRICATION
BAKE-OUT
SAFE TRANSPORT
Circle 19 on p. 76 or go to adlinks.che.com/50980-19
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 21
cluding n-butenes and C4 streams
from naphtha cracking and fluid-
catalytic-cracking (FCC) operations
can be processed to produce butadi-
ene. The feedstock versatility of this
process makes it feasible to retrofit
into an existing facility or construct
new-build plants. Testing at a dem-
onstration plant with a capacity of
200 metric tons per year (m.t./yr)
and development of a process de-
sign package were both completed
in 2013, and technology licensing
activity commenced in 2014. Cur-
rently, feasibility studies for com-
mercial plants are being executed
with potential customers.
Bio-based butadiene
While many groups are investi-
gating on-purpose butadiene solu-
tions that utilize existing chemical
streams (like butene or butane) as
feedstock, others are investing in
bio-based routes to alleviate con-
cerns associated with butadiene
availability. Last fall, a bio-based
butanediol process technology from
Genomatica (San Diego, Calif.; www.
genomatica.com) was awarded the
Kirkpatrick Chemical Engineering
Achievement Award (Chem. Eng.,
November 2013, pp. 1519). In the
months since winning the Kirkpat-
rick Award, Genomatica has an-
nounced multiple milestones in de-
veloping its next bio-based process
technology focused on the production
of bio-based butadiene. They have
announced two high-profile partner-
ships with Braskem S.A. (So Paulo,
Brazil; www.braskem.com.br) and
Eni S.p.A.s (Rome; www.eni.com)
chemical subsidiary Versalis.
The combination of these strate-
gic collaborations gives Genomatica
global reach for the licensing of its
bio-butadiene technology. Under a
December 2013 agreement, Genom-
atica and Braskem will together de-
velop and commercialize a process
to make butadiene from renewable
raw materials. With this agree-
ment, Braskem gains exclusive
licensing rights to use the technol-
ogy in the Americas. The Versalis
partnership is targeted on licens-
ing activities for bio-butadiene pro-
duction in Europe, Asia and Africa,
AMACS 24-7 Emergency Service Available at (281) 716 - 1179
2013 Amacs Process Towers Internals. All Rights Reserved.
www.amacs.com
VALVE SIEVE OR PERFORATED BUBBLE CAP
CARTRIDGE TRAYS DUAL FLOW GALLERY DISTRIBUTOR
TRAYS FOR EVERY PROCESS
For gas processing, rening and a
wide range of process applications.
AMACS offers a wide selection of
alloys, sizes and congurations to
meet any mass transfer requirement.
As a leader in the research and design
of trays and tower internals, AMACS
can design to your specications
or improve your process with our
latest technologies.
Valve (numerous options)
Sieve or perforated
Bubble cap
Cartridge trays
Dual Flow
Gallery Distributor Tray
For all your process internal requirements
make one stop- AMACS.
Circle 6 on p. 76 or go to adlinks.che.com/50980-06
22 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront
and will specifically focus on using
non-food lignocellulosic biomass as
a raw material.
Genomatica sees global viability
for bio-butadiene, citing shifting re-
finery feeds and an increased aware-
ness of product sustainability. The
company says that the butadiene
development program is off to a fast
start, with $100 million in industry
investment and strategic partners
with commercialization intent.
Genomaticas butadiene plat-
form employs proprietary micro-
organisms that convert biological
feedstocks into butadiene directly
or via an intermediate. All of the
steps in these metabolic pathways
have demonstrated functional ex-
pression. A patent was granted in
November 2013 covering a method
for the direct production of butadi-
ene. According to the company, the
process involves all aspects of sepa-
ration and purification to deliver
a chemical product that will work
in existing applications without
requiring changes by downstream
users. This versatility, along with
the use of renewable feedstocks, are
the main aspects that have drawn
commercial interest in the process.
Another company seeking a re-
newable pathway to butadiene is
Cobalt Technologies (Mountain
View, Calif; www.cobalttech.com),
which has developed a fermentation
platform that takes sugars sourced
from cellulosic biomass and converts
them into n-butanol, which can sub-
sequently be reacted to form many
other chemicals, including butadi-
ene. The ability to leverage the flex-
ibility of n-butanol as a chemical
starting point is a huge benefit, says
Andy Meyer, president of Cobalt
Technologies. N-butanol is an in-
credible building block into other re-
newable chemicals and fuels. Given
our cost position in the production of
n-butanol, and given the impact of
shale gas on C4 molecules, it became
a natural fit to pursue butadiene as
a product platform.
According to the company, Cobalt
is finalizing a joint-development
agreement with strategic partners
in Asia, which will complete the
work required to scale the remain-
ing elements of the technology.
Upon successful completion, we
plan to move forward with commer-
cialization with our Asia partners
and further monetize the technol-
ogy globally through other licensing
and partnership arrangements,
says Meyer. Cobalt is also in the
preliminary stages of pursuing var-
ious opportunities in the U.S.
Cobalt and Genomatica are just
two of the many companies at the
forefront of bio-based butadiene
technology. Several other notable de-
velopments have been announced in
the past year, including the BioBut-
terfly project, a research partnership
between Axens (Rueil-Malmaison,
France; www.axens.net), IFP Ener-
gies Nouvellas (Rueil-Malmaison,
France; www.ifpenergiesnouvelles.
com) and Michelin (Clermont-Fer-
rand, France; www.michelin.com)
to create and market a process for
producing bio-sourced butadiene.
Scoped for eight years, the project
is focused on the need for alterna-
tive raw-material sources for the
synthetic rubbers industry, and,
with 52 million in backing, the
partners hope that it will be a major
step toward a more environmentally
friendly rubber industry.
Additionally, Global Bioenergies
(Evry, France; www.global-bioen-
ergies.com) was granted a patent
in April 2014 for production of bio-
butadiene via enzymatic dehydra-
tion. Further development of this
process is the scope of a partner-
ship with Synthos Group S.A. (Os-
wiecim, Poland; www.synthosgroup.
com). Also investigating enzymatic
technology for butadiene produc-
tion is Arzeda Corp. (Seattle, Wash.;
www.arzeda.com), which has de-
signed specific enzymatic pathways
to convert biomass into butadiene.
For the process development of this
technology, Arzeda has collaborated
with Invista (Wichita, Kan.; www.
invista.com), citing butadiene price
volatility as one of the main drivers
behind this partnership.
Utilizing waste gas
A novel technology developed
by LanzaTech (Skokie, Ill.;
www.lanzatech.com) aims to create
Circle 38 on p. 76 or go to adlinks.che.com/50980-38
a platform for butadiene synthe-
sis from waste-gas feedstocks. The
feed gases for LanzaTechs process
can come from a variety of sources,
both industrial and biological, in-
cluding offgases from steel mills
and CPI plants, and syngas gener-
ated from municipal solid waste or
agricultural waste.
Together with SK Innovation,
(SKI; Seoul, South Korea; www.
sk.com) in a partnership announced
in late 2013, LanzaTech plans to
commercialize a two-step platform
to create butadiene from waste
gases that contain carbon monox-
ide (CO). First, through a patented
fermentation process, an acetogenic
microbe converts the CO from the
feed gas into 2,3-butanediol and
ethanol. Via downstream catalytic
technology provided by SKI, the
2,3-butanediol fermentation inter-
mediate undergoes double dehydra-
tion to form 1,3-butadiene.
The biochemical pathway used
in LanzaTechs process (called the
Wood-Ljungdahl pathway) for fer-
mentation to 2,3-butanediol is
shown in Figure 5. A hallmark of
this process technology is its ability
to run continuously rather than in
batches. Syngas can be constantly
processed and butanediol can con-
tinuously pass to the catalysis
step, says Alice Havill, senior pro-
cess engineer and separations lead
at LanzaTech. With advanced lab-
scale testing underway at both com-
panies, a pilot demonstration of this
technology is planned for the first
quarter of 2015 at SKIs research
facility in Daejeon, Korea, with an
eventual goal of making the plat-
form available for licensing.
Another benefit of this process is
its versatility. As seen in Figure 5, ei-
ther CO or CO
2
can be used as a raw
material to synthesize buta-
diene. LanzaTech has part-
nered with Invista on further
development of processes
utilizing a CO
2
/H
2
feedstock,
targeting the nylon 6 and 6,6
product chain as a potential
application for the butadiene prod-
uct. Commercialization for this proj-
ect is expected in 2018.
Commercial interest has been
piqued, especially in the areas of
polymers, synthetic rubbers and in-
dustrial solvents, with companies
requesting samples of fermentation-
based butadiene as a drop-in re-
placement for butadiene produced
via traditional methods. LanzaTech
touts the technologys unique feed-
stock as a driver for commercial
success, citing price fluctuations as
a crucial factor in the development
of new butadiene-production tech-
niques, not only in the case of crude
oil, but also in the sugar-based feed-
stocks that are used for many bio-
based routes, which can experience
similar price volatility. According to
Havill, LanzaTech has developed
an innovative platform that re-
cycles carbon-rich waste gases and
residues and converts these local,
highly abundant waste and low-cost
resources into sustainable, valuable
commodities. She continues, saying
The need for new butadiene sources
will only be exacerbated by the rising
global demand for butadiene-based
products. This will especially be evi-
dent in the growing consumption of
rubber in emerging markets the
commercial reach is global.
Eliminating butadiene
The use of alternative raw materi-
als can also allow companies to de-
crease their reliance on butadiene.
At the 2013 PCI American Nylon
Symposium, Rennovia, Inc. (Menlo
Park, Calif.; www.rennovia.com)
announced the demonstration of a
continuous bio-based pathway to
hexamethylenediamine (HMD) that
utilizes widely available, renewable
feedstocks. Traditionally, HMD, an
Reaction
section
Purifcation
section
Butenes/butanes
Oxidative dehydrogenation
Air, steam
Crude
butadiene
To butadiene
extraction unit
Quenching
Absorption
Degassing
Solvent
Solvent recovery
Wastewater
Off gas
FIGURE 4. MCCs on-purpose
butadiene process is designed
to be compatible with a variety
of C4 feedstocks
Mitsubishi Chemical
GLO8AL LXlLh1lSL lN
AU1OMA1lON
Llectric actuators Ior
industrial valve automation
heliable, powerlul, el cienl. AUMA
oller a large porllolio ol aclualor
and gearbox lype ranges.
Aulomaling all lypes ol induslrial
valves in all markel segmenls
lnlegralion inlo all commonly
used conlrol syslems
High corrosion proleclion
Service worldwide
Learn more
aboul
our
aulomalion
solulions
www.auma.com
Circle 8 on p. 76 or go to adlinks.che.com/50980-08
Newsfront
important component
in the production of ny-
lons and polyurethanes,
is produced from a buta-
diene hydrocyanation
reaction forming adi-
ponitrile, which is then
hydrogenated to HMD.
Rennovias new process
uses glucose as a raw
material for a two-step
catalytic conversion to
HMD no butadiene
is required. The process
has been demonstrated
to run continuously,
and the construction of
a mini-plant is planned
for 2015. In February
2014, Archer Daniels
Midland Co. (ADM; De-
catur, Ill.; www.adm.
com) invested $25 mil-
lion for the advance-
ment of Rennovias re-
newable technologies.
Subsequently, Genom-
atica announced in
August 2014 that they
would begin develop-
ing bio-based routes
to various nylon inter-
mediates, including
HMD, caprolactum and
adipic acid.
Others are searching
for alternative products
altogether. In addition
to their butadiene part-
nership with Genomat-
ica, Versalis has joined
forces with agricultural biomaterials
company Yulex Corp. (Phoenix, Ariz.;
www.yulex.com) for the manufacture
of biorubber materials using guay-
ule, a renewable, non-food crop, as a
raw material. Plans for an industrial
production facility in Europe are un-
derway, where the biorubber will be
a supplementary product to Versalis
traditional butadiene-based syn-
thetic rubber. Once again, forecasted
scarcity and price volatility of buta-
diene are among the factors driving
this partnership.
On-purpose chemistrys future
In the case of butadiene, it is clear
that on-purpose and bio-based
technologies are not
merely a fad. Com-
panies are investing
and showing confi-
dence in the com-
mercial potential of
these processes. On
the future of on-pur-
pose technologies in
the CPI, Dows Bob
Maughon remains
optimistic about the
industrys willing-
ness to adapt, say-
ing, In general, we
were forced into the
co-product ecosys-
tem and we learned
to love it. I am con-
vinced that we will
learn to love the on-
purpose world even
more. He also em-
phasizes one major
positive aspect of an
on-purpose economy:
companies can apply
capital to make pre-
cisely the product
they want. There
are obviously great
opportunities in the
field of on-demand
production technolo-
gies for byproducts
of crude-refining
processes. Beyond
butadiene, speaking about the
next on-purpose trend on the ho-
rizon, Maughon explains that cy-
clopentadiene, like butadiene, is a
cracker co-product with many uses.
However, there are no on-demand
routes to it currently. Also among
the chemicals affected by the move
toward ethane-only cracking are
isoprene and piperylene, as well
as aromatics like benzene, toluene
and xylene. It seems likely that
companies will continue investi-
gating advanced butadiene process
technologies, and perhaps they will
follow suit for cyclopentadiene
and other chemicals.
Mary Page Bailey
We live process engineering
and special manufacturing
www.sms-vt.com
Your porlner in developing new
producls ond processes
Buss-SMS-Canzler
Buss-SMS-Canzler GmbH
Koiserslroe 13-15 - 3551O Bulzboch - 0ermony
Tel. -/ O 33 - 85 - O - Fox. -/ O 33 - 85 - 2/
F-Moil. [email protected]
Thin Film
Dryer
Continuous contact drying of
liquids, slurries, sludges and
pastes.
Circle 12 on p. 76 or go to adlinks.che.com/50980-12
Wood -Ljungdahl
pathway
CO/CO
2
CO/CO
2
CO
2
CO
2
CO
2
Fd
red
Fd
ox
H
3
C S
O
O
O
OH
O O
OH
O
OH
OH
OH
H H
H H
H
H
1,3-Butadiene
Catalysis step
OH
CoA
Acetyl-CoA
Pyruvate
synthase
Pyruvate
Acetolactate
synthase
(S)-Acetolactate
(R)-Acetoin
Acetolactate
decarboxylase
2,3-Butanediol
dehydrogenase
D-(-)-2,3-Butanediol
NAD(P)H
NAD(P)
+
Pyruvate
FIGURE 5. LanzaTechs
fermentation/catalysis
platform follows this bio-
chemical pathway
LanzaTech
Maintenance, inspection, and heat treating services are integral to ensure safe operations
and prolong the life of your equipment. Team provides critical services to assist with
scheduled maintenance, repairs, and inspections. Our expertise, flexibility and global
resources are available 24/7/365 to ensure you keep your equipment running.
Team experts are available 24 hours a day, 7 days a week, 365 days a year.
Call TEAM today: 1-800-662-8326
www.teamindustrialservices.com
Minimizing Downtime. Maximizing Performance.
YOUR SINGLE SOURCE
FOR SERVICE:
+
Bolting/Torquing
+
Concrete Repair
+
Emissions Control
+
Exchanger Services
+
Field Machining
+
Fitness for Service
+
Heat Treating
+
Hot Tap/Line Stop
+
Isolation Test Plugs
+
Leak Repair
+
Manufacturing/Engineering
+
Mechanical Integrity
+
NDE/NDT Inspection
+
Specialty Welding
+
Turnkey Tank Program
+
Valve Insertion
+
Valve Repair
INDUSTRIES SERVED:
KEEP IT RUNNING.
Circle 47 on p. 76 or go to adlinks.che.com/50980-47
26 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront Newsfront
W
hether the application is
reactive extrusion, phar-
maceutical manufacturing,
compounding or plastics
processing, finding the sweet spot
where increased efficiency, flexibil-
ity and lower capital expenditures
are well balanced is the holy grail of
todays extruder operations.
Most industries that employ ex-
trusion are facing a very different
market than what existed just a few
years ago. This new marketplace is
fraught with process challenges,
including the development of new
materials with different charac-
teristics, more varieties of materi-
als being run on one line, frequent
changeovers from one product to
the next and fierce market competi-
tion from overseas.
Unfortunately, many processors
have large production machines
that were not designed for the rig-
ors of the current marketplace.
Older machines were created to be
efficient when making continuous
runs for days and weeks at a time,
says Adam Dreiblatt, director of
process technology at Century Ex-
trusion (Traverse City, Mich.; www.
centuryextrusion.com), but now
they are running for only hours be-
fore they are stopped and changed
over to accommodate the next prod-
uct, and again turned on for just a
few hours before they are stopped
and changed over yet again.
Because of the diversity of prod-
ucts required in todays market and
because of the make-to-order world
we now live in, the companies that
make these materials face severe
challenges when it comes to mak-
ing their products in a cost effec-
tive way, Dreiblatt says. Their cost
margins and productivity are being
squeezed because of the way the
global world is evolving.
For example, in the compounding
industry, he says, manufacturers of
resins that are used to make arti-
cles like cell-phone cases and auto-
motive parts, are often charged with
finding new materials for better per-
formance. It might be necessary to
create a new blend of plastics, addi-
tives and rubbers for a new product,
such as a bumper and then another
new resin for something like a valve
cover and still another material for
radio knobs, says Dreiblatt. As a
result, manufacturers of the resins
and compounds are rapidly expand-
ing their portfolio of products. How-
ever, they cant just make a bunch
and keep it on a shelf in their ware-
house because it costs too much to
inventory and they run the risk of
making more than their customers
will want. Because of these factors,
compounders require production
equipment that is capable of not
only producing a variety of materi-
als, but also changing over quickly
from one run to the next.
The good news is that the equip-
ment is now evolving to meet the
challenges presented by the de-
mands of this new marketplace,
Dreiblatt says. New machines
are being designed for faster turn-
arounds and changeovers. High-
performance screw and barrel
materials are being developed to
reduce wear and tear on the equip-
ment to reduce downtime. Some
extruders are being designed with
lower costs in mind. And some are
being designed for greater effi-
ciency and throughput.
And, no matter what the indus-
try or application, efficiency, flex-
ibility and lower costs are the most
requested items on the extrusion
wish list.
Increased efficiency
While products and materials are
being innovated, the equipment
tends to be developed more slowly,
which leaves many users of extrusion
technology running new processes
on old equipment or, sometimes,
new equipment that operates on
the same principle that has existed
for the past 40 years, says Michael
Lazorchak, global product manager,
mixing systems with B&P Process
Equipment and Systems (Saginaw,
Mich.; www.bpprocess.com). This is
not conducive to efficiency and reli-
ability for todays processors.
However, equipment providers
such as B&P are finally beginning
to address the need for increased ef-
Newsfront
A changing marketplace necessitates
the need for extrusion equipment
with more flexibility and greater efficiency
EXTRUDERS
EVOLVE FOR
THE NEW WORLD
FIGURE 1. The TriVolution
offers twelve pin-fight inter-
meshing zones in the cross
section, versus two for a typical
twin-screw extruder or three for
a typical continuous kneader
B&P Process Equipment and Systems
Find out more at
water.gea-hx.com
engineering for a better world GEA Heat Exchangers
Pure water is the very essence of life. In actual fact: our HX-Factor
makes it possible (HX = HEAT EXCHANGE). This promise of per-
formance is backed up by our unique quality outlook for water
purification and waste water treatment and assures resource-
protective handling of our worlds most precious asset. Our solu-
tions assure you energy-efficient water treatment technology for
potable water supplies, aquaculture, and waste water disposal.
Safe and reliable. Pour on the water!
No water without HX-Factor
Water treatment
with HX-Factor.
For vital purity.
Circle 24 on p. 76 or go to adlinks.che.com/50980-24
28 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront
ficiency from the machines process
zone, rather than through power
capabilities alone. For newer ap-
plications, such as reactive extru-
sion and devolatilization, as well as
traditional chemical industry ap-
plications, such as processing cata-
lysts, mastics, graphite and carbon-
based materials, and in plastics
compounding, B&Ps TriVolution
kneader (Figure 1) offers a non-tra-
ditional operating principle in an
effort to increase efficiency.
The kneader leverages elonga-
tional mixing to stretch and dis-
perse viscous materials. Elonga-
tional mixing imparts a high degree
of particle droplet deformation and
breakup to finely disperse materi-
als without excessive shear or heat
generation. The TriVolution offers
twelve pin-flight intermeshing
zones in the cross section versus two
for a typical twin-screw extruder
or three for a typical continuous
kneader. The key to improved ef-
ficiency lies in these twelve zones,
where elongational flow action oc-
curs, says Lazorchak.
Several aspects of the design en-
able efficient extrusion, especially
in devolatilization and reactive ex-
trusion. Smaller channels and quick
multiplication of flow splitting for a
given throughput result in thinner
material thicknesses. This creates
shorter diffusion paths for volatiles
to escape from the melt. Larger free
volume for a given screw diameter
offers longer residence times. And,
says Lazorchak, narrow residence-
time distribution, coupled with ex-
cellent surface-area renewal, pro-
mote efficient temperature control
of the melt. Volatile byproducts can
be efficiently removed and a greater
number of molecular chains are ex-
posed for higher reaction rates.
In industries such as pharmaceu-
ticals, where there may be frequent
changeovers and contamination is
a risk, efficiency in changeover and
cleaning the equipment, in addition
to better controls for more efficient
throughput, are high priorities. For
this reason, L.B. Bohle Maschinen +
Verfahren GmbH (Enningerloh, Ger-
FIGURE 2. The
BCG extruder
offers a monob-
lock design that
features no dead
spaces or connec-
tions, which makes
installation and
cleaning easy
L.B. Bohle
BLASTS HAPPEN
GET PROVEN PROTECTI ON.
AS THE INDUSTRYS LEADING MANUFACTURER OF SUCCESSFULLY TESTED
BLAST-RESISTANT BUILDINGS, RedGuard is the name you can count on when lives are
on the line. Whether youre looking for a little extra space for your next turnaround or a
permanent addition to your existing site, we provide proven protection for your peace of mind.
855.REDGUARD
LEARN MORE ABOUT WHAT MAKES REDGUARD THE SAFE CHOICE IN BLAST RESISTANCE.
Circle 3 on p. 76 or go to adlinks.che.com/50980-03
Graham Engineering
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 29
many; www.lbbohle.de) introduced
a newly designed GMP-compliant
twin-screw extruder, supplied by a
continuous mass-controlled powder
dosing unit and a continuous liquid
dosing unit (Figure 2). The BCG
extruder offers a monoblock design
that features no dead spaces or con-
nections, which makes installation
and cleaning easy. The real torque
measurement on each screw in-
dividually allows for tighter con-
trol of the process, says Andreas
Altmeyer, head the service center at
L.B. Bohle.
Finding flexibility
Sometimes increased efficiency also
comes in the form of greater flex-
ibility. Handling a variety of mate-
rials and frequent product changes
means there are often changeovers,
which amounts to a lot of downtime.
This is especially true when extrud-
ing plastics, says David Schroeder,
president and CEO of Graham En-
gineering (York, Pa.; www.graha-
mengineering.com). Downtime or
loss of production and material due
to changeover is expensive and time
consuming. Product quality can
also suffer, resulting in scrap, until
optimal production is achieved,
explains Schroeder. In addition,
equipment is a significant capital
investment. A single line or ma-
chine capable of producing a variety
of parts or products helps leverage
that investment.
For this reason, Graham Engi-
neering offers rapid in-line color
change via its accumulator heads.
While many competitive heads can
take as much as 8 to 12 h to purge
from one color to another, Graham
heads can generally change from
one color to another in 30 to 60
min, using only simple hand tools.
After removing some bolts, the hy-
draulic cylinders on the head are
used to lift the diverter and plunger
out of the head body. The diverter
plunger and head body can then be
cleaned using a brass scraper. When
finished, the diverter and plunger
Introducing Corzan

HP, creating piping systems with better

CORROSION RESISTANCE
AND HIGH-TEMPERATURE PERFORMANCE
all made with
LUBRIZOL TECHNOLOGY
TO GIVE YOU MORE INSIDE.

for transmission of CHEMICAL FLUIDS

See how the details on the inside make all the difference on the outside.
Call a piping systems consultant at 1.216.447.7397
or visit corzancpvc.com to learn more.
Choose Corzan HP for Chemical Processing, Semiconductor & Electronics,
Water Treatment, Industrial Manufacturing, Mining and Power
Generation applications.
Corzan HP is a high-pressure, high-temperature, high-impact-strength
piping system engineered with Lubrizols specially formulated chlorinated
polyvinyl chloride (CPVC) compounds that meet the ASTM D1784
certifcation for 24448 cell class. Its the rst pipe that meets
ASTM F441 material classication 4120-06, with a pressure rating
25% higher than standard CPVC at 180F (82C).
2014 The Lubrizol Corporation, all rights reserved. All marks are the property of The Lubrizol Corporation.
The Lubrizol Corporation is a Berkshire Hathaway company.
GC 140681
Follow us
on Twitter
@LZ_CPVC
Circle 32 on p. 76 or go to adlinks.che.com/50980-32
FIGURE 3. A confgurable rotary-wheel
extrusion blow molder allows for high
outputs of a range of bottle sizes used in
beverage, dairy and household products
on a single platform
30 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront
are lowered and fastened back into
the head. Quality parts with a new
color can be manufactured within a
few shots.
When it comes to extrusion
blow molding, Graham has also
developed a configurable version
of its rotary-wheel extrusion blow
molder for high outputs of bottles
(Figure 3). It is now configurable
to accommodate a range of bottle
sizes used in beverage, dairy and
household products on a single
platform, says Schroeder.
And, the American Kuhne brand
(a part of the Graham Group;
www.americankuhne.com), offers
a modular extruder. Interchange-
able extruders, the barrel, screw
and feed section, are available on
one common, stationary base, says
Schroeder. This allows one ex-
truder to swing into place, rapidly
replacing the other, enabling offline
purging or service, while another
extruder can be preheated and
aligned, minimizing downtime.
Flexibility is equally important
in the compounding industry, says
Paul Lloyd, business unit direc-
tor with Farrel Pomini (Ansonia,
Conn.; www.farrel-pomini.com).
In the compounding industry, the
ability to adapt in markets that are
constantly changing is important.
There are frequent formulation
changes based on the development
of new additives, new customer re-
quirements or new market oppor-
tunities, he says. So the ability
to have an asset that is flexible is
desirable because extrusion equip-
ment is expensive and traditionally
difficult to change out.
To help provide flexibility, Farrel
Pomini offers a two-stage machine
with a mixer at the top and an ex-
truder underneath, which allows
the production of quality compounds
in the mixing section and the pres-
surization in the extrusion section.
In traditional extruders, these two
processes are combined, explains
Lloyd. Providing a two-stage pro-
cess with a mixer and extruder that
are separate from each other allows
additional process variables to be
employed, which allows flexibility
to be achieved through the control
system rather than making me-
chanical changes as you would on a
traditional extruder. This allows a
single machine to process a range of
materials without any mechanical
changes to the equipment, he says.
The companys latest CP4000
Compact Processor (Figure 4) allows
more flexibility in variables such as
throughput rate, rotor speed, tem-
perature and discharge-gate posi-
tion to improve or change mixing
parameters. Because of the ability
to make changes via programming
the necessary process changes into
the recipe on the control system,
the machine is inherently more
flexible than a traditional extruder,
1967 Nova Pro Street
Creating Value.
Carver Pump Company
2415 Park Avenue
Muscatine, IA 52761
563.263.3410
Fax: 563.262.0510
www.carverpump.com
Do you have flows up to
9,900 GPM (2,000 m3/hr),
heads up to 720 Ft (220 M), speeds up
to 3,500 RPM, and temperatures up to 500F
(260C)? Then you need Carver Pump
Process Maxum Series muscle!
With an extended range of hydraulic coverage and
rugged construction, the Process Maxum Series is ideal
for Industrial Process applications. Manufactured in
35 sizes, standard materials include WCB, WCB/316SS,
316SS and CD4MCu, with others available upon
request. A variety of options include various types of
mechanical seals and bearing lubrication/cooling
arrangements, auxiliary protection devices and certified
performance testing. Whatever your requirements,
let us build the muscle you need!
Process Maxum
Circle 14 on p. 76 or go to adlinks.che.com/50980-14
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 31
which typically requires the use of
tools and additional components for
changeover of products.
Also operating on a new premise
to increase flexibility when com-
pounding and injecting product-
specific formulations, the injection
molding compounder (IMC) from
KraussMaffei (Munich, Germany;
www.kraussmafei.com) links the
continuous extrusion process with
the discontinuous injection-molding
process in a single-stage process.
This set up protects the material
by processing at one temperature.
The process starts with individual
materials being metered by mass.
The plasticized and homogenized
material moves from the extruder
into the barrel of the injection unit
via a heated runner. In the injec-
tion and holding pressure phase,
the extruder continuously supplies
the material through a buffer to
ensure consistent formulation qual-
ity. The material is shaped in the
twin-plated clamping unit on one of
the standard injection molding ma-
chines offered by the company. The
IMC makes it possible to purchase
less expensive raw materials, initi-
ate compounding tailored to the ap-
plication and run small production
series. It also provides an increase
in flexibility in the way users can
process and create new combina-
tions of a vast assortment of mate-
rials, from blends to real reinforcing
agents to fillers.
Reduced costs
While efficiency and flexibility help
reduce operating costs, the capital
investment of the equipment itself
is often a deterrent when it comes to
updating equipment to suit the de-
mands of this globally competitive
marketplace. And, with many com-
pounders moving overseas, theres
been an abundance of extrusion
equipment suppliers cropping up in
China and other Asian countries, of-
fering machines at deeply reduced
DONT IGNORE
POTENTIAL
HAZARDS
IN YOUR FACILITY
PROVEN QUALITY & RELIABILITY
FOR NEARLY 70 YEARS
Visit the new FIKE.COM to use our easy online DiscCalc

tool
or find an expert in your area
TRUST FIKE
RUPTURE DISCS
0omprehens|ve se|ect|on of ASNF, 0F and 3-A cert|hed d|scs
0omp|ete ||ne of products des|gned for 0|P/S|P app||cat|ons
0ed|cated team of eng|neers and techn|ca| support
877-814-3453
[email protected]
Circle 22 on p. 76 or go to adlinks.che.com/50980-22
Farrel Pomini
FIGURE 4. The CP4000 Compact
Processor allows more fexibility in
variables such as throughput rate, rotor
speed, temperature and discharge-gate
position to improve or change mixing
parameters
32 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Newsfront
prices. However, many of these ma-
chines are not designed and crafted
with the same quality parts found
in European- and American-made
machines. But, some European and
American suppliers are partner-
ing with selected Asian companies
so that the critical parts are made
in Europe or the U.S. and the non-
critical parts hail
from China, where
the assembly is also
done under the di-
rection of the estab-
lished firms. This
results in the creation
of a quality piece of
equipment provided at a
lower cost, says Dreiblatt. This is
important in todays economy be-
cause in any application, theres a
lot of cost pressure to get down to
the lowest capital cost possible, yet
the company purchasing the equip-
ment still needs high productivity.
But unless the supplier has part-
nered with an established expert,
the machines coming out of China
are not high-quality, high-perfor-
mance machines.
He says his own company has es-
tablished a partnership to provide
machines of this hybrid nature.
For example, the Century Extru-
sion APEX Series of twin-screw ex-
truders (Figure 5) is engineered to
provide optimal value to compound-
ers around the world. Engineering
teams from both Century Extru-
sion and Ruiya Extrusion in China
worked closely to integrate the best
design features and materials into
three flexible extruder models, al-
lowing the equipment to deliver
high performance, flexibility and re-
duced cost of ownership. The series
features both standard and high-
torque gear boxes that are designed
and manufactured in Europe, and
the machines are available with
Centurys cold-formed, high-torque
shaft technology, as well as bar-
rels and screws that are made from
Centurys advanced materials and
wear technology.
Obviously, more extrusion equip-
ment providers are beginning to
understand the changing world
in which their customers are cur-
rently operating and are working
hard to create lower cost machines
that provide higher efficiencies and
more flexibility to meet the needs of
processors in this fast-paced, chang-
ing marketplace.
Joy LePree
Circle 28 on p. 76 or go to adlinks.che.com/50980-28
FIGURE 5.
The APEX Series
of twin-screw extrud-
ers features both standard
and high-torque gear boxes.
Barrels and screws are made from ad-
vanced materials and wear technology
Century
Extrusion
F
rom September 30 to Octo-
ber 2, more than 700 exhibi-
tors from over 25 countries
will again be coming to the
Nuremberg exhibition center to
attend Powtech, one of the worlds
leading trade fair in its field, show-
ing everything the chemical process
industries (CPI) needs to handle
powders, granulates and bulk ma-
terials including analysis. What
follows is a small sample of some
of the new products that will be on
display during the exhibition.
One principle, many possibilities
with this mixer
This company is demonstrating
the versatile application of its hori-
zontal Ploughshare mixer. Both a
batch mixer, FKM, and a continuous
mixer, KM, are on display. Both ma-
chines are available with drum vol-
umes of between 130 and 30,000 L.
The company is also presenting the
Type N 5 laboratory mixer (photo).
With a drum volume of 5 L, the Type
N 5 laboratory mixer is available for
product and process development,
as well as for small-scale production.
All mixers operate by the special
mixing principle of the mechanically
generated fluidized bed developed by
the company. The so-called Plough-
share paddles rotate close to the
wall of a horizontal cylindri-
cal drum, lifting the mixing
components from the drum walls
and hurling them from the ma-
terial bed into the open mixing
chamber. The complete product is
constantly drawn into the mixing
process, ensuring maximum mix-
ing intensity. Hall 5, Stand 222
Gebr. Ldige Maschinenbau GmbH,
Paderborn, Germany
www.loedige.de
Preventive re protection for
safer production
The Spark Extinguishing System
BS 7 (photo) is used to protect mills,
silos, filters and pneumatic convey-
ing facilities. The wide range of prod-
ucts generally offers a detector with
the required sensitivity for each of
these applications. Depending on
the application, the detectors can be
combined with different techniques
of spark elimination, such as water,
steam, gas or diversion. The Ultra-
high-Speed (UHS) Extinguishing
Technology BS 7 UHS reduces the
reaction time by a factor of two or
three. This allows very short extin-
guishing distances of less than 2 m.
Hall 6, Stand 122 Fagus-GreCon
Greten GmbH & Co. KG, Alfeld/Ha-
nover, Germany
www.grecon.com
This bagging system ensures
accurate lling
The fillpac bagging system (photo)
can be incorporated flexibly into ex-
isting packaging lines. It is equipped
with a calibratable scale. The elec-
tronic weighing unit ensures that
the fillpac always achieves accu-
rate filling quantities. Special soft-
ware enables the weigher to com-
municate continuously with the
filling spouts. This enables users
to get the best out of their packag-
ing lines, as it is not necessary to
reject bags with incorrect weights
from the process. Hall 1, Stand 135
Beumer Group GmbH & Co. KG,
Beckum, Germany
www.beumergroup.com
The advantages of
ameless venting
Since its introduction in the 1980s,
the Q-Rohr (photo, p. 32I-2) and
Q-Box flameless venting solutions
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
32I-1
Note : For more information, circle the 3-digit number
on p. 76, or use the website designation.
POWTECH 2014
Gebr. Ldige
Maschinenbau
Fagus-GreCon Greten
Beumer Group
32I-2 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Show Preview
have been continuously developed
and improved for applications in a
whole range of sectors in the CPI.
The advantages of flameless vent-
ing include the fact that the entire
production process remains inside
the building and
there is no need
for expensive,
bulky venting
ducts that re-
quire modifica-
tions to be made
to existing struc-
tures. The integrated
bursting disc is fitted
with a signaling unit that
immediately reports any in-
cidents to the process-control
system. The special stainless-
steel mesh filter inlet ensures
that the pressure rise and
increased noise level associ-
ated with free vented explo-
sions are massively reduced
to negligible levels in the
production room. Dust and
flames are retained by the
mesh filter inlet. The Q-Rohr
has a round design, so it is
vacuum-resistant and ideal
for the protection of pneumatic
conveying systems as well as many
other applications. Hall 4, Stand
215 Rembe GmbH Safety + Con-
trol, Brilon, Germany
www.rembe.de
This machine enables lling
compact bags for the rst time
The new Roto-Packer for small
bags (photo) is based on the com-
panys Adams technology, and fills
powder-type bulk products into
compact polyethylene (PE) bags for
the first time. The packer achieves
a rate of up to 600 bags per hour
and features a stepless bag-weight
selection of 110 kg. Filling into
bags made from a film tube or pre-
made bags is now possible. Using
an additional module, the user may
also form the bag from a flat film
within the Roto-Packer system.
The bags are sealed air-tight and
are impermeable to the weather.
They are clean, compact and pro-
vide for an attractive appearance.
The user saves costs in packaging
and storage, says the company. Hall
1, Stand 533 Haver & Boecker
OHG, Oelde, Germany
www.haverboecker.com

Determine concentration and
particle size with this unit
Promo (photo) is an aerosol spec-
trometer for analyzing both par-
ticle size (200 nm to 100 m) and
determining concentration (<1
10
6
particles/cm
3
). All data are dis-
played on a large touchscreen, and
can be analyzed in realtime. Promo
has a standard interface and can
be controlled by a process-control
system or by a simple Labview
program, which makes the device
suitable for control and monitor-
ing applications. The optical fiber
technology enables measurements
at locations that are difficult to
reach and in hazardous areas.
Using fiber-optic cables, the welas
sensors can easily be connected to
the Promo and exchanged at will.
These sensors allow measure-
ments at temperatures between
90 and 470C and at a pressure
range from 300 mbar to 10 bars.
Hall 5, Stand 156 Palas GmbH,
Karlsruhe, Germany
www.palas.de
Tableting with
continuous inline weighing
The KTP 420X (photo) is a ver-
satile, high-speed tablet press
that includes the new CWC (Con-
tinuous Weight Control) system.
Equipped with numerous patented
features, this machine compresses
up to 360,000 tablets per hour. It
is suitable for the production of
mono-layer, bi-layer or core tablets
(tab-in-tab), and it can also be used
to process poorly flowing materials.
The patented CWC in-line scale al-
lows the weight of the tablet being
produced to be measured continu-
ously at the discharge as the prod-
ucts are pressed, without destroy-
ing them. The weighed tablets are
placed in the good channel using
compressed air. As a result of the
new process, there is no longer
Haver & Boecker OHG
Palas
Romaco Group
Rembe
Magnochem. More choice.
More possibiIities.
KSBs unique and comprehensive range of products makes it a global
leader able to cater for even the most demanding chemical applications.
The latest innovation for critical fluids: the Magnochem mag-drive pump.

Wide range of variants: new operating modes for low-boiling and solids-laden fuids

Energy effciency: the modular design system for magnetic couplings allows the
pump to be tailored to the optimum operating point

Innovative technology: cutting-edge manufacturing methods and latest developments
Find out more at vvv.ksb.comlmagnochem
Our technoIogy. Your success.
Pumps

Valves

Service
Visit us at ACHEMA in frank!urt
!rom 15 to 19 1une 2015 in haII 8,
stand H14
Circle 30 on p. 76 or go to adlinks.che.com/50980-30
32I-4 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Show Preview
any need to make sample tablets
in order to check the weight, and
product loss is reduced to zero.
Hall 6, Stand 456 Romaco
Group, Karlsruhe, Germany
www.romaco.com
These blowers are very energy efcient
At Powtech, this compressed-air specialist will be show-
casing its EBS Series of high-efficiency screw blowers
(photo). Not only are these new screw blowers up to
35% more efficient compared to conventional rotary
blower designs, they also offer significant advantages
over comparable screw blowers on the market when it
comes to energy efficiency. To ensure that the projected
savings become actual savings during operation, the
company specifies effective overall power consump-
tion data, as well as the usable flowrate, in accordance
with ISO 1217 in Appendix C, or E as applicable. The
high-efficiency, energy-saving blower ranges now cover
air deliveries from 2 to 72 m
3
/min at up to 1,000 mbar
gauge pressure and 500 mbar vacuum. Hall 4.0, Stand
123 Kaeser Kompressoren SE, Coburg, Germany
www.kaeser.com
A dedusting lter module for milling machines
The new, patent-pending ProFi-Clean (photo) is a com-
pact de-dusting and filtering device with an automatic
blow-back system. The stand-alone dedusting filter can
easily be retrofitted to existing sieve mills, and allows
the filtering and separation of powder particles in the
extracted air. The de-dusting filter is cleaned automati-
cally by pressure impulses. This guarantees that the
whole cartridge surface area remains clog-free and the
powder is blown-back into the product. The pneumatic
control system is built on the filter housing, therefore the
filter device works completely independently. The stand-
alone de-dusting filter is easily integrated into existing
and new process plants. Hall 1, Stand 442 Frewitt
Fabrique des machines SA, Granges-Paccot, Switzerland
www.frewitt.ch
This dryer increases the capacity of spray dryers
To satisfy the requirements of companies that need to
increase the capacity of their expensive spray-drying
towers or wish to avoid or delay the need to invest in
an additional spray-drying tower, this company has de-
Kaeser
Dinnissen
Frewitt Fabrique
des machines
ARCA
Flow Group
worldwide:
Competence in valves, pumps & cryogenics
Subsidiaries and partners in Switzerland, the Netherlands,
India, P.R. China, Korea and Mexico!
ECOTROL

control valve
Advantages,
that should not be kept quiet!
High reliability guaranteed by
precision manufacturing processes
and quality control
Emission control and leakage
conforming to the highest international
standards
Tubeless, integrated mounting of
positioners acc. to VDI 3847
Minimal life cycle cost
A range of awarded patents
Take advantage of the most technically
innovative control valve in a generation,
up to DN 400 (16")!
ARCA Regler GmbH, D-47913 Tnisvorst
Phone +49-2156-7709-0, Fax -55, [email protected]
www.arca-valve.com
The State
of the Art
solution!
Request
Technical
Information or
a Quotation:
T
h
e

Q
u
i
e
t

W
o
r
k
-
H
o
r
s
e
!
Circle 7 on p. 76 or go to adlinks.che.com/50980-07
GEA Process Engineering
GEA Process Engineering A/S
Gladsaxevej 305, DK-2860 Soeborg, Denmark
Tel: +45 39 54 54 54, Fax: +45 39 54 58 00
[email protected], www.gea.com
engineering for a better world
To make superior powders, look for a GEA Niro drying system. We specialise in supplying
industrial drying systems designed to match your exact product and plant specications, and
with more than 10,000 references worldwide our expertise is unsurpassed. Our comprehensive
product range includes GEA Niro spray dryers, uid bed systems, spray congealers and the
SWIRL FLUIDIZER. At our extensive test facilities, the most experienced test engineers and
process technologists in the business will help you move rapidly from idea to product development
and protable production.
GOOD
POWDER
We know
what makes a
Circle 25 on p. 76 or go to adlinks.che.com/50980-25
32I-6 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Show Preview
veloped a new drying method using
its Pegasus Drying Unit (photo, p.
32I-4). Wet-mix products first go
through a conventional pre-drying
process, after which they undergo
a final low-temperature drying
stage in the Pegasus Drying Unit.
This not only saves a great deal of
energy, but also ensures optimum
retention of color, aroma, flavor and
heat-sensitive components, such as
vitamins. During the final drying
process, the double-shafted paddle
mechanism built into the Dry-
ing Unit is used to gently suspend
powders, granules, and granulates
in the air, creating a fluidized bed.
Precisely at the moment that the
ingredients are gently suspended,
air is injected at a temperature of
between 80 and 140C into the Dry-
ing Unit, resulting in a very effi-
cient, fast and even drying process.
Hall 4.0, Stand 323 Dinnissen
B.V., Sevenum, the Netherlands
www.dinnissen.nl
Silo lters for all
sectors of the CPI
The Sirius silo filter (photo) has a
large diameter, enabling filtration
surface areas from 3 to 34.4 m
2
. Fil-
ter housings are made of stainless
steel (1.4301/304). The system is
said to be maintenance-friendly, re-
quiring only one person to perform
maintenance. These filters are espe-
cially suited for silos and containers
that are filled pneumatically with
bulk material. Due to the stainless-
steel design, the filters can be used
in all industries ranging from the
construction sector to the phar-
maceutical industry. Hall 4, Stand
239 Waiweldai Anlagentechnik
GmbH, Grnsfeld, Germany
www.waiweldai.de
Perform superne grinding
with this ball mill
The CoBall-Mill annular gap bead
mill (photo) is an in-line milling
system for manufacturing suspen-
sions and other products of almost
any viscosity. This mill is the ideal
solution for superfine grinding of
active pharmaceutical ingredients,
such as sterile ophthalmic medi-
cations and ointments, as well as
numerous cosmetics and chemical
applications. The unusually narrow
milling chamber is filled between
50 and 80% full of beads made from
wear-resistant ceramic materials.
The CoBall-Mill boasts a high mill-
ing power in relation to its very
small chamber and the grinding en-
ergy input can be as much as 8 kW/
dm
3
. Users profit from extremely
homogeneous results with particle
sizes on the nanoscale. Thanks to
the distinctive conical geometry of
the rotor-stator tool, the mill in-
puts the milling forces directly into
the product. The residence time in
the milling chamber and hence
the production process overall
UWT
Waiweldai Anlagentechnik
FrymaKoruma
Italian quality
Your vacuum drying specialist
[email protected] | italvacuum.com
Planex System:
patented paddle vacuum dryer
equipped with eccentric agitator
Criox System:
patented rotary
vacuum dryer/pulverizer
Multispray Cabinet Dryer:
tray vacuum dryer
with extractable shelves
Saurus939:
low maintenance
LubriZero vacuum pump
30/09 - 02/10
Nuremberg (Germany)
Stand: 4-447
Brilliant technology
Circle 29 on p. 76 or go to adlinks.che.com/50980-29
Circle 37 on p. 76 or go to adlinks.che.com/50980-37
32I-8 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Show Preview
is therefore significantly reduced.
Hall 6, Stand 357 FrymaKoruma
GmbH, Neuenburg, Germany
www.frymakoruma.com
This capacitance level switch
handles many applications
The RFnivo 3000 (photo, p. 32I-6)
is a new capacitive level switch for
bulk solids and is used as overfill
protection, as well as a demand or
empty detector in process or storage
containers. The device is a single-rod
probe that has been designed to de-
tect bulk solid materials without the
use of temperature-limiting compo-
nents. The RFnivo is available in
stainless steel grade 1.4301 (303) to
1.4404 (316L), with PPS or ceramic
insulators and optional Teflon seals.
While the RFnivo with ceramic in-
sulators can cope with extreme pro-
cess temperatures up to 500C, the
standard version with PPS insula-
tors can handle temperatures up
to 240C. The
RFnivo is suitable
for use in contain-
ers with overpressure of
up to 25 bars as standard.
The electronics guarantee
a very high sensitivity when used
with the correlating length of a sin-
gle-rod probe. Bulk materials with a
dielectric value of 1.5 and more can
be detected, which covers most bulk
materials. Hall 4A, Stand 123
UWT GmbH, Betzigau, Germany
www.uwt.de
Integrated solutions
for process containment
The new Isocharge system (photo)
is a low-cost method of both dis-
pensing and charging bags into re-
actors or receiving systems via the
Powder Transfer System (PTS).
The Isocharge combines the advan-
tages of isolation and laminar flow
technology, providing high contain-
ment of < 1g/m
3
per 8 h TWA (time
weighted average). The stations
chamber is open to the side allowing
easy bag introduction. A simple door
only needs to be closed during WIP
(wash in place) to prevent splashes.
All WIP fluids can be drained from
the chamber via the PTS into the re-
actor, which also cleans the transfer
hose and the PTS. The Isocharge will
be showcased in combination with
the Continuous Liner filling system,
equipped with a Dosivalve for accu-
rate filling. Hall 1, Stand 213 DEC
Dietrich Engineering Consultants
SA, Ecublens, Switzerland
www.dec-group.net
Gerald Ondrey
Get Chemical Engineerings plant
cost index to improve plant cost
estimatesand delivered in advance
of the print edition!
For more than 37 years, chemical process industries
professionals- engineers, manager and technicians,
have used Chemical Engineerings Plant Cost Index
to adjust process plant construction costs from one
period to another.
This database includes all annual archives (1947 to
present) and monthly data archives (1970 to present).
Instead of waiting more than two weeks for the print or
online version of Chemical Engineering to arrive,
subscribers can access new data as soon as its calculated.
Resources included with Chemical Engineerings Plant
Cost Index:
ElecIrohic hoIiIcaIioh oI mohIhly updaIes as sooh as
they are available
All ahhual daIa archives (1947 Io presehI)
MohIhly daIa archives (1970 Io presehI)
OpIioh Io dowhload ih Ecel IormaI
Subscribe today at www.chemengonline.com/pci
17817
www.alexanderwerk.com | +49 (0)2191 795 0
Hall 1, Booth 1 - 448
30.9. - 2.10. in Nuremberg
Circle 5 on p. 76 or go to adlinks.che.com/50980-05
DEC Dietrich Engineering Consultants
Thermoplastic buttery valve
enables many stopping positions
With its advanced, one-piece ther-
moplastic design and construction,
the patent-pending BYV Series
Butterfly Valve (photo) offers a vari-
ety of design advances, including a
hand lever that features a 72-spline
interlock mechanism that allows
for 19 stopping positions (every 5
deg). Pneumatic or electric actua-
tors are available. Available in a
variety of thermoplastic mate-
rials (for the body, disc and
liner), in sizes from 2 to 12
in. (DN50300), these but-
terfly valves have a stem-
bearing and seal-retainer
design that enables accurate
stem positioning and reten-
tion, says the firm. Hayward
Flow Control, Clemmons, N.C.
www.haywardflowcontrol.com
Valve handles high-molecular-
weight uids in compressors
The Magnum HammerHead valve
(photo) is a versatile valve that can
be applied to all brands of recip-
rocating compressors, and is spe-
cifically designed for applications
involving high-molecular-weight
fluids at both low and high com-
pressor speeds. This valves design
has been re-engineered using com-
putational fluid dynamics and finite
element analysis, improving the
valve flow area by 60% compared to
standard Magnum valves. Its new
streamlined flow path (with opti-
mized seat, guard and lift areas),
not only maximizes the valve flow
area but provides greater tolerance
to particles and liquids in the gas,
says the company, and allows it to
be applied at higher compressor
speeds compared to other poppet
valves. Dresser-Rand, Houston
www.dresser-rand.com
Check valve prevents backow
and odor at discharge points
The CheckMate Inline Check Valve
(photo)is ideal for backflow preven-
tion and odor mitigation from out-
falls, stormwater, oceans, rivers and
interceptors. The valve, available in
sizes from 4 to 72 in., has an elas-
tomer, fabric-reinforced unibody
construction. It can open to near
full pipe diameter, thereby reducing
head loss while maximizing the flow
capacity of the outfall, which is par-
ticularly helpful in low-lying areas
where limited driving head
is available, says the com-
pany. Tideflex Technolo-
gies, a Div. of Red Valve Co.,
Carnegie, Pa.
www.tideflex.com
Full plastic construction
provides a range of advantages
Traditional plastic regulating
valves (PRV) which involve top
and bottom plastic elements held
together by metal screws are
susceptible to leakage due to differ-
ential expansion coefficients of the
component materials, and require
regular retorquing of the metal
screws during maintenance inter-
vals. By comparison, this firms fully
plastic PRV (photo) has consistent
temperature expansion coefficients,
so it provides stable, long-term set-
point behavior without the need for
regular adjustment, says the firm.
Its compact design enables the
valve to fit in confined spaces. It is
available in several polymers to en-
sure fluid compatibility, at a range
of standard- and low-pressure op-
tions. Online support is available
to assist with proper sizing. GF
Piping Systems Ltd., Schaffhausen,
Switzerland
www.georgfischer.com
A family of forged valves for se-
vere operating conditions
The new Pacific Forged line of high-
pressure gate, globe and check
valves is available for use in power,
oil-and-gas and chemical markets.
These forged components are de-
signed for applications that are
likely to encounter high stress and
high thermal cycling. A countoured
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
33
Note : For more information, circle the 3-digit number
on p. 76, or use the website designation.
FOCUS ON
Valves
Hayward
Flow Control
Dresser-Rand
Tideflex Technologies
GF Piping
Systems
Focus
34 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
shape and proprietary hard-face
overlay process makes these valves
resistant to cracks and delamina-
tion, reducing maintenance and
downtime, says the company. Multi-
stage ultrasonic testing is standard
on all forgings and finished valves
to ensure that they are suitable for
use under severe process conditions.
Crane ChemPharma & Energy,
Houston
www.cranecpe.com
This family of block valves is
designed to ensure re safety
The FM Fire-Safe Thermal and Elec-
tro-Thermal Shutoff Valves (photo)
are used as emergency block valves
for fire safety applications. They are
available in three types of assembly
(ball valve, flanged ball valve and
butterfly valve). These valves, with
a body made from carbon steel or
stainless steel, are available in a
range of sizes and end-connection
styles. A variety of fusible links, de-
signed to withstand different tem-
perature thresholds, are available.
The companys Configurator tool
helps specifying engineers design
their assembly, and generate part
numbers and quotes. Assured
Automation, Clark, N.J.
www.assuredautomation.com
Double-ange, slide-gate valve
isolates gravity-fed solids
The Mucon DSV Double Flange
Slide Gate Valve (photo) provides an
in-line option to help isolate grav-
ity-fed, free-flowing powders and
granules, especially for applications
that require a flange connection at
the outlet. It has a slim, lightweight
alloy design. A stainless-steel slide
gate provides standard, tamper-
proof locking, so that the user can
lock or tag the valve in the closed
positions. The device also provides
grounding points for applications in
which static charge may be a prob-
lem. A lightweight pneumatic ac-
tuator assembly can be added as a
simple retrofit and easily removed
to return the unit to basic hand op-
eration. Kemutec, Bristol, Pa.
www.kemutecusa.com
Valve designs are available for
high-pressure urea service
This companys Swivldisc Gate
Valves (photo) are available in sizes
ranging from 0.5 to 4 in. The wedge
gate design uses a flexible disk,
which permits the seating surface to
achieve optimal alignment and thus
a tighter seal than is possible with
standard wedge gates, says the com-
pany. They are available in ASME/
ANSI pressure classes through
#4500. They are available in a range
Assured
Automation
Kemutec
Conval
Circle 2 on p. 76 or go to adlinks.che.com/50980-02
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 35
of standard and specialty materi-
als, and options include bypass,
air or motor actuators. Conval,
Somers, Conn.
www.conval.com
Positioner provides fast re-
sponse for large valves
This control-valve positioner pack-
age (photo) ensures precise posi-
tioning with fast response times
over the entire operating range, for
applications with strokes of 60 mm
or greater. The package consists of a
positioner and a connection to sev-
eral volume boosters with different
air-output capacities. Closing and
opening times of less than two sec-
onds can be achieved over the en-
tire positioning range. This device
is especially useful for compress or
bypass valves (anti-surge valves).
Samson Controls, Surrey, U.K.
www.samsoncontrols.co.uk
Ball valves help users meet
lead-elimination requirements
The Pro-Press family of lead-free
ball valves, available in sizes from
0.5 to 2 in. and made from a pro-
prietary silicon-bronze alloy, is spe-
cifically designed for press systems.
Multiple configurations and multi-
ple thread or connector options are
available. The valve stem is avail-
able in Eco Brass or Type 316 stain-
less steel. Viega, Wichita, Kan.
www.viega.us
Portable valve-actuator device
can service multiple valves
The EasiDrive portable valve ac-
tuator is a versatile tool for use
with valves that require a large
number of turns or that are other-
wise difficult to operate because of
high torque or harsh climate
conditions. Using this tool,
an operator can easily drive
multiple valves, and it is de-
signed to prevent both the ap-
plication of excessive torque
and torque kickback, thereby
reducing operator fatigue and
the risk of injury. This device
is adaptable to any type or
size of valves, and provides a
low-cost alternative to perma-
nent actuators with no perma-
nent power supply required, says
the company. It is said to be ideal
for moving tight or partially seized
valves. Smith Flow Control, Er-
langer, Ky.
www.smithflowcontrol.com

Select or design the valve you
need for any uid service
This firm offers a broad array of en-
gineered valves to manage hydrau-
lic fluid oil, air, refrigerants, water,
chemicals, fuel and gases in a vari-
ety of industrial applications. Mate-
rial options include steel, stainless
steel, brass, aluminum and Monel,
and all forms of fittings are avail-
able. Custom engineering and man-
ufacturing helps to reduce costs,
assembly time and potential leak
points. Fluid Line Products, Wil-
loughby, Ohio
www.fluidline.com

These digital valve controllers
can be mounted remotely
The Fieldvue DVC6200p series of
digital valve controllers are de-
signed for applications in which ac-
cessibility, extreme temperatures
(up to 120C or 250F), extreme
vibration or confined space makes
integral mounting impractical.
With the remote-mount version of
DVC6200p, only the valve-position
feedback is mounted on the control
valve; the remainder of the digital
controller can be mounted more
than 300 ft away (in a preferable
environment) . With no linkages to
wear, loosen or corrode, the feedback
unit can withstand extreme operat-
ing conditions. Emerson Process
Management, Marshalltown, Ia.
www.fieldvue.com
Suzanne Shelley
Samson Controls
Proven
performance
ROTOFORM
GRANULATION
FOR PETROCHEMICALS
AND OLEOCHEMICALS
High productivity solidication of
products as different as resins, hot
melts, waxes, fat chemicals and
caprolactam has made Rotoform

the
granulation system of choice for
chemical processors the world over.
Whatever your solidication
requirements, choose Rotoform for
reliable, proven performance and a
premium quality end product.
High productivity
on-stream factor of 96%
Proven Rotoform technology
nearly 2000 systems installed
in 30+ years
Complete process lines or
retrot of existing equipment
Global service / spare parts supply
www.processsystems.sandvik.com

Sandvik Process Systems
Division of Sandvik Materials Technology Deutschland GmbH
Salierstr. 35, 70736 Fellbach, Germany
Tel: +49 711 5105-0 Fax: +49 711 5105-152
[email protected]
Circle 45 on p. 76 or go to adlinks.che.com/50980-45
A new line of electrically driven
solids-handling pumps
These-auto prime pumps (photo)
have a capacity of 100 to a maxi-
mum of 6,500 m
3
/h. The BA diesel-
driven pumps have been actively
used on the market for many years.
Now, with the development of a
new standard norm block construc-
tion (NMC) the company offers a
modular and compact electrically
driven pump design. Using high-
efficiency pumps and IE2 electric
motors, the pumps offer maximum
performance at minimal cost. In
addition to a standard control box
and soft starter, the pump sets can
also be provided with a frequency
converter; which ensures maximum
control over the pumping process,
not just by using the automatic
start/stop but also by increasing
or decreasing the speed of the elec-
tric motor. These pumps can be
deployed in sewage or dewatering
applications. BBA Pumps B.V.,
Doetinchem, the Netherlands
www.bbapumps.com
Level detectors approved for
SIL2 and SIL3 applications
The radiometric gauge SENSseries
LB 480 (photo) has been awarded
SIL2/SIL3 certification, making
this company the first supplier
providing SIL-certified radiometric
systems for both level (point level
or continuous level) and density
measurements. The high level of
availability and operational safety
of the SENSseries LB 480 detec-
tors was intensively tested and
approved by TV Sd according
to IEC 61508:2010. In redundancy
installations (one out of two; 1oo2)
SIL3 can also be achieved. Unlike
other instrumentation available on
the market that require frequent
recalibration, this companys pat-
ented stabilization methods correct
for temperature and aging effects.
Berthold Technologies GmbH &
Co. KG, Bad Wildbad, Germany
www.berthold.com
Intelligent and robust fuel
owmeters and readout units
Fuel-View (photo) is a compact,
lightweight and cost-effective so-
lution for measuring the fuel con-
sumption and operating time of ve-
hicles, tractors, river vessels or any
mobile or fixed installations with
diesel engines. The device can be
used for protecting and preventing
theft of fuel, preventing overstate-
ment of readings and intervention
and the patented method of mea-
suring different engine operating
times. New are models for measur-
ing diesel, gasoline, fuel oil, biofuel
or other viscous liquids up to 500
L/h. Special differential meters are
now available with two integrated
measuring chambers, one for mea-
suring the supply line and one for
measuring the return line to calcu-
late fuel consumption in realtime.
Mass Flow Online B.V., Apel-
doorn, the Netherlands
www.massflow-online.com
A new generation of
dry running agitator seals
This company has launched a new
generation of dry-running shaft
seals for agitators. In addition to
the known benefits of this type of
mechanical seal, the new SeccoMix1
(photo) is also silent running and
has been prototype-tested for use
in ATEX category 1 (zone 0). These
shaft seals are used in mixers, agi-
tators, dryers and filter strainers.
Dry-running SeccoMix seals need
no supply system, so they have a
significant advantage over liquid
or gas-lubricated seals. Given this
36 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Note : For more information, circle the 3-digit number
on p. 76, or use the website designation.
BBA Pumps
Berthold
Technologies
Mass Flow Online
EagleBurgmann
Chemical Engineering is getting an
online facelift. The rst part of our
makeover is a dynamic new URL
www.chemengonline.com
Save us in your favorites today.
And remember, www.che.com is NOW
www.chemengonline.com
38 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
New Products
saving on the purchase and opera-
tion of a seal-supply system, the
investment costs for a dry-running
single seal are as little as 30% of
those for an equivalent liquid-lu-
bricated seal, says the company.
EagleBurgmann GmbH & Co. KG,
Wolfratshausen, Germany
www.eagleburgmann.com
Get the message across about
workplace hazards
Providing information to, and com-
municating with, staff and col-
leagues in the workplace is essen-
tial, particularly when hazards,
incidents or near-misses occur that
may impact on others. An effective,
low-cost solution to getting the
message across is the Near Miss/
Incident Reporting System (photo),
which is an easy way to manage and
document health and safety issues.
The standard display board is avail-
able in a three-column format with
standard 50 or 30 cards deep and
measures 409 mm wide and is sup-
plied fully assembled, complete with
headings and 200 Incident T Cards.
There is also the option to have the
system made to a bespoke format.
T Cards Direct, Kent, U.K.
www.tcardsdirect.com
This control system now has
enhanced alarm functions
The newly released Centum VP
R5.04 (photo, p. 39) is an enhanced
version of this companys flagship
integrated production control sys-
tem. This new Centum release fea-
tures enhanced alarm and batch
T Cards Direct
Uraca
8200 Bessemer Ave. Cleveland, Ohio 44127 T (877) 503-9745
www.fedequip.com [email protected]
(877) 503-9745 or
www.fedequip.com
The Equipment Soluons Company
Federal Equipment Company Buys
and Sells Used Chemical Equipment
10,000 Gal DCI Storage Tank, 316L S/S
150 Gal. Ross Double Planetary Mixer,
Model DPM 150, 316L S/S, Unused
500mm X 250mm Rousselet Robatel
Peeler Centrifuge, Hastelloy C22
Examples of Typical Inventory
Circle 21 on p. 76 or go to adlinks.che.com/50980-21
functions. With the Centum system, a prominently
colored tag mark is displayed on the HMI screen
next to any measurement reading that falls outside
the normal range. With Centum VP R5.04, these col-
ored tag marks now come in a variety of easily rec-
ognizable shapes that indicate the importance of a
measurement item and the severity of an anomaly
(critical, high-risk, medium-risk, low-risk and so on).
New audible alarms have also been added to provide
information on the severity and equipment location
of an anomaly. Through the use of color, shape and
sound, operators can quickly and intuitively recognize
the significance of a specific alarm, thereby allowing
for improved operational safety. Yokogawa Corp. of
America, Newnan, Ga.
www.yokogawa.com/us
Tank cleaning in explosion-proof zones
By means of high-pressure water, various incrustations
can be removed inside of autoclaves, reactors, spray
towers and vessels. The pump unit discharges high-
pressure water (up to 1,600 bars) through the companys
Tank Cleaning Head Nozzles (photo). The water jet cuts
through the deposits, removing hard incrustations by
means of precise rotating movement, thus reaching the
inner surfaces in an optimal way. Thanks to their ex-
amination certificate according to EC directive 94/9/EC
for category 1, the tank-cleaning heads series TWK are
permitted to be used in explosion-proof areas zone 0 and
zone 20. Optimized displacement circle diameter allows
the use of cleaning heads even with small access open-
ings. Uraca GmbH & Co. KG, Bad Urach, Germany
www.uraca.com
This valve controller is suited
for hostile environments
The Fisher Fieldview DVC6200p series of digital valve
controllers is an ideal solution for applications in which
accessibility, extreme temperatures (up to 120C),
extreme vibration or confined space make integral
mounting difficult or impractical. Industries such as
pulp and paper, and metal and mining have typically
preferred to isolate valve-mounted instruments from
harsh environments. With the remote-mount version of
DVC6200p, only the valve position feedback is mounted
on the control valve, while the remainder of the digital
valve controller can be mounted over 90 m away in a
less severe or more accessible environment. Emer-
son Process Management, Marshalltown, Iowa
www.emersonprocess.com
Yokogawa

Pumps Manufacturing Company www.3pprinz.com

[email protected]
Eccentric Disk Pumps
Pompe 3p

and Pera-Prinz are Trademarks of 3P Prinz

Srl
Reliability

Performance
Available in Standard and
Exotic Materials

Since 1952
Circle 1 on p. 76 or go to adlinks.che.com/50980-01
Circle 23 on p. 76 or go to adlinks.che.com/50980-23
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 39
40 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
New Products
These dry vacuum pumps
have a high throughput
The adixen vacuum dry pump
(photo) is said to meet current and
future challenges of cutting-edge
procedures in the coatings industry
(LED/OLED, flat/touch panel and
solar). The multistage roots vac-
uum pumps of the ADH series are
designed for challenging processes
where lots of dust accumulates, cor-
rosive gases are pumped and high
temperatures are present. These
vacuum pumps distinguish them-
selves with their high gas through-
put and a pumping speed of 600 to
4,500 m
3
/h. The pumping speed for
the light gases that are particularly
important in innovative coating
processes is especially high. A moni-
toring system monitors the pumps
in the process. The strongly reduced
energy and water consumption re-
sult in low operating costs. Their
silent operation (<65 dBA) makes
them ideal even for serial instal-
lations. Pfeiffer Vacuum GmbH,
Alar, Germany
www.pfeiffer-vacuum.com
This horizontal-paddle vacuum
dryer has a concentric agitator
Maximum ease of cleaning, mainte-
nance and internal inspection are
the qualities that make the Cos-
moDry System suitable for multi-
product applications. The CosmoDry
System consists of a horizontal cy-
lindrical chamber, equipped with
a concentric agitator, fitted with a
heated shaft that is dismountable
in sections a feature that sets
it apart from conventional paddle
vacuum dryers. The peculiar config-
uration of the agitator enables con-
tinuous stirring of the product and
facilitates its thermal exchange,
reducing drying time. Moreover, it
was designed to limit mechanical
and thermal stresses, thus allowing
the treatment of thermo-sensitive
products. The CosmoDry System is
manufactured in volumes ranging
from 150 to 4,400 L, and the loading
capacity can vary from 30 to 80% of
the chambers volume. Italvac-
uum S.r.l., Turin, Italy
www.italvacuum.com
Gerald Ondrey
Circle 27 on p. 76 or go to adlinks.che.com/50980-27
Pfeiffer Vacuum
T
he Water Environment Fed-
eration (Alexandria, Va.;
www.wef.org) is holding its
annual Weftec exhibition
and conference from Sept. 27Oct.
1, 2014 at the Ernest N. Morial Con-
vention Center in New Orleans, La.
The event will feature numerous
technical sessions and committee
meetings, as well as a host of exhib-
itors showcasing new products and
services for the water and wastewa-
ter industries. This show preview
highlights a small selection of the
products that will be on display at
this years Weftec exhibit hall.
Install this owmeter in areas
of extreme ow conditions
The FPI-X dual-sensor electromag-
netic flowmeter (photo) provides
accurate and repeatable measure-
ments under extreme flow condi-
tions, including environments with
swirl and other flow disturbances
in the line. Designed for use in close
proximity to cascading or multiple-
pump arrays, the FPI-X mag meter
delivers 0.5% accuracy. Even when
installed in areas where establish-
ing a symmetrical velocity-flow pro-
file is extremely difficult, such as
near pumps, valves, elbows or head-
ers, the FPI-X performs to specifi-
cation. Booth 6737 McCrometer,
Inc., Hemet, Calif.
www.mccrometer.com
These diaphragm pumps feature
a simple valve and head design
This companys Series 7000 me-
chanically actuated diaphragm
pumps (photo) simplify operations
by eliminating the use of contour
plates on the liquid side of the dia-
phragm. Designed with water and
wastewater applications in mind,
the pumps straight-through valve
and head design allows for im-
proved flow characteristics. Self-
priming Series 7000 pumps feature
a maximum flow capacity of up
to 1,135 L/h at 150 psi, with suc-
tion lift exceeding 20 ft on water-
like chemicals. Additionally, Series
7000 pumps can handle viscosities
as high as 5,000 cP. Booth 1529
Neptune Chemical Pump Co.,
North Wales, Pa.
www.neptune1.com
Polypropylene lter media
resists erosion and buckling
BIOdek polypropylene (PP) trick-
ling filter media provides an alter-
native to traditional polyvinyl chlo-
ride (PVC) media used in biological
wastewater-treatment processes.
BIOdek filter media can accommo-
date many process requirements,
types of flow patterns and channel
sizes for a variety of trickling appli-
cations. Since PP is not as stiff as
PVC, the filter media can be more
easily inspected without fear of
damage to the media personnel
can walk on top of the media (photo)
for inspection without the require-
ment of a protective walking grate.
Also, PP media is more resistant
against erosion and buckling due
to its lower density when compared
with PVC. Booth 2939 GEA Heat
Exchangers, Bochum, Germany
www.gea-heatexchangers.com
These PVC owmeters are
built with no moving parts
The P-420 line of vortex-shredding
flowmeters (photo) are intended for
use in process water, brine, corro-
sive fluids and chemical-treatment
applications. These flowmeters are
constructed of conventional PVC or
chlorinated PVC, without moving
parts that can stick, bind or coat.
Electronic output is from a 420-
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
41
Note : For more information, circle the 3-digit number
on p. 76, or use the website designation.
weftec
the water quality event
2014

McCrometer
Neptune
Chemical Pump
GEA Heat Exchangers
Universal Flow Monitors
42 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Show Preview
mA two-wire transmitter with no
local display. It is rated as intrinsi-
cally safe when used with barriers.
The electronics package is totally
potted and not vulnerable to the
installed environment. Booth 7711
Universal Flow Monitors, Inc.,
Hazel Park, Mich.
www.flowmeters.com
Continuously monitor free
chlorine without using reagents
The Signet 4630 Free-Chlorine
Analyzer System (photo) provides
a turnkey solution for measuring
free chlorine in water. Designed
with amperomatic sensing technol-
ogy, the system incorporates a clear
flow cell, flow regulators, sensors,
filter and rotameter all in one com-
pact unit. With this system, contin-
uous, realtime monitoring of chlo-
rine is achieved without the use
of reagents, thus lowering main-
tenance and calibration require-
ments associated with chlorine-
monitoring activities. The ability to
accomodate manual or continuous
pH compensation further increases
accuracy in the Signet 4630s free-
chlorine readings. The built-in flow
regulator automatically controls
flow across the sensors membrane,
reducing bubbles, and allowing
for a wide range of inlet pressures
ranging from 1 to 8 bars. The units
flow cell can be easily opened for
thorough cleaning and removal
of algae or hard-water deposit
buildup. Booth 7209 GF Piping
Systems, Tustin, Calif.
www.gfps.com
Eliminate stagnation in
nished-water storage tanks
This companys TMS mixing sys-
tem (photo, p. 43) consists of a com-
bination of patented check-valve
technology and a piping manifold
that separates the inlet and outlet.
Designed to improve the quality of
water in finished-water storage res-
ervoirs, the TMS can be installed for
new or existing water-storage tanks
of all shapes and sizes to eliminate
stagnation and short-circuiting.
Operating with intrinsic differen-
GF Piping
Systems Creating tangible solutions...

GEM Valves features diaphragm
valves, buttery valves, angle seat
and globe valves, lined metal valves,
and multiport block valves.
3800 Camo C|ee| Pa||way B0||d|ng 2600 S0|te 120
At|anta, GA 30331 7e|: 678-553-3400 Fax: 678-553-3459
www.gemu.com
Be s0|e to v|s|t GEMU va|ves /nc.
at WEF7EC 2014, Seot 29 - Oct 1
at t|e New O||eans
Mo||a| Convent|on Cente|,
New O||eans, /o0|s|ana.
WEFTEC Booth #9103
Circle 26 on p. 76 or go to adlinks.che.com/50980-26
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 201 43
tial pressure, the TMS requires low
energy input. The systems built-in
check valve is constructed of elasto-
mers and demands very little main-
tenance. Booth 2331 Tideflex
Technologies, Carnegie, Pa.
www.tideflex.com
This metering pump provides
single-component maintenance
The Qdos 60 peristaltic metering
pump (photo) is designed to reduce
chemical metering costs when com-
pared to conventional solenoid or
stepper-driven, diaphragm meter-
ing pumps. Qdos pumps eliminate
the need for ancillaries, boost pro-
ductivity and cut chemical waste
due to accurate, linear and repeat-
able metering. Also, simple instal-
lation and maintenance lower total
cost of ownership. Maintenance
tasks are expedited due to the
pumps patented single-component,
contained tool-free technology. Qdos
60 pumps are suited for numerous
applications, including disinfection,
pH adjustment and flocculation of
drinking water, wastewater and
industrial process water, as well
as reagent dosing and metering in
mineral-processing tasks. Booth
3207 Watson-Marlow Pumps
Group, Wilmington, Mass.
www.watson-marlow.com
A blending system designed for
water-treatment liquid polymers
The DynaBlend Liquid Polymer Di-
lution/Feed System is engineered
to effectively activate and blend
all types of liquid polymers for the
water and wastewater industries.
Designed with easy disassembly
and inspection in mind, the system
features a non-mechanical mixing
chamber and an injection check
valve, eliminating many concerns
about maintenance and reliability.
DynaBlend systems are available
in a variety of models, configured
for various throughputs, polymer
properties and operating condi-
tions. Booth 1529 Fluid Dynam-
ics, North Wales, Pa.
www.fluiddynamics1.com
Mary Page Bailey
Tideflex Technologies Watson-Marlow Pumps Group
Circle 4 on p. 76 or go to adlinks.che.com/50980-04
The Chemical Engineering bookstore
offers a variety of industry topics
you will come to rely on.
Envlronmental Management:
Alr-Pollutlon Control
Envlronmental Management: Wastewater
and Groundwater Treatment
Fluld Handllng
Gas-Solld and Llquld-Solld Separatlon
Llquld-Llquld and Gas-Llquld Separatlon
Managlng Bulk Sollds
For a complete list of products, visit the
Chemical Engineering bookstore now.
http://store.che .com/product/book
17792
mengonline
Department Editor: Scott Jenkins
C
ollecting representative samples of heat-
transfer uid for routine quality checks falls
short of the goal if safety or the environ-
ment is compromised. While users should
consider their systems unique design features
in consultation with their safety and health
experts, incorporating the tips below can help
to avoid common potential safety concerns as-
sociated with sampling these uids, which may
be at extreme temperatures. Understanding
these safety issues is the rst step in planning a
safely conducted task.
Ergonomics
Safe access to heat-transfer-uid sample ports
is a key part of an ergonomically designed
station. Important aspects of a well-designed
sampling station include the following:
* Cleor slondlng oreo wllh unobslrucled polh
of egress
* Helghl ol somple porl below cheslhlgh, lo
avoid upper body splash
* Llmlled exlenl ol reoch requlred lo ovold
body strain
* Spoce beneolh somple porl lo ollow honds
free placement of a properly labelled ush
bucket
* Monsllp, solld Noor surloces lo prevenl drlps
to a lower level
* Globe volves ln somple porl ore prelerred
for the best control of owrate
Extreme temperatures
Representative samples are best collected
during operation, when the uid is uniformly
mlxed lhroughoul lhe syslem. Heollronsler
uids routinely reach temperatures that can
present thermal burn hazards. The following
tips are for sampling hot streams:
* Revlew solely dolo sheels [SDS| lor lhe
personol prolecllve equlpmenl [PPE| lhol ls
required for the uid being sampled, as well
as its physical and chemical properties, and
hazard information
* se o somple cooler lo reduce Nuld lempero-
lure lo below P3C [200F| lo prolecl somple
composition integrity
* Veor gloves lhol provlde chemlcol ond lher-
mal protection, as well as a splash apron,
eye goggles and a face shield
* lnspecl lhe porl oreo lor unlnsuloled conlocl
points to avoid
* Avold drlps whlch moy occur belore, durlng
or after collection
* Do nol remove PPE unlll lhe porl ond somple
bottle are secured
Splashes and spray
Even wllh lhe proper PPE ln use, lnlllollng Now
from the sample port is a transient operation
that can result in splatter or spray, and efforts
should be made to limit the splash potential.
Since the uid may be hot, it is important to
take precautions against accidental hot-uid
contact to avoid thermal burns. Thermal burns
are the single greatest safety concern to
personnel working with high-temperature uids
and equipment. Use of a globe valve can
provide better ow control when opening the
sample port.
Think ahead to plan what actions will be
taken in the event of an unexpected spray.
Anllclpole pressure on lhe llne when open-
ing the port valve, and open the valve gradu-
ally. Stand to the side so that any spray will
be directed away from potential physical
contact. One technique to better control the
sample stream is to install a short length
of small-diameter tubing on the sample
valve outlet, which steadies the stream and
also permits easy insertion into the neck of
sample bottles.
When ushing the sample port prior to
collecting the good sample, direct the stream
lnlo o dry buckel. Any molslure ln lhe Nush
bucket can result in violent splatter of the hot
heat-transfer uid into the vicinity, if the sample
stream is above the boiling point of water.
Take the time needed to sample the uid
safely. Rushing to perform this task can pose
unnecessary safety risks for those collecting the
uid samples.
Spills
By expecting the unexpected, we can prepare
adequately to avoid potential spills and their
consequences, or minimize their extent and
lmpocl. A wellploced somple porl wlll be ol
ground level with little exposure to sewers or
Noor drolns. A smoll, curbed oreo con help
keep smoll releoses conlolned. Above oll, el-
forts should be taken to keep potential releases
of organic heat-transfer uids from drains and
waterways. If a storm drain is in the area, it
should be adequately covered or otherwise
blocked during sample collection.
Hlghlemperolure heollronsler Nulds ore
commonly organic liquids, and suitable dry,
absorbent media should be available in the
area for response to stabilize and aid in clean-
up. These uids are also likely to be com-
bustible, and clean-up should be performed
promptly.
Some heat-transfer uids may have unique
spill clean-up and disposal methods that are
directed by their manufacturers, so refer to the
producl SDS lor speclhc guldonce.
Flnolly, ony Nuld resldues wlll olso creole o
hazard by making walking surfaces, handrails,
or coated structures slippery. To avoid slips
and falls, and to avoid fueling a re, these
residues should also be cleaned. Oil-absorbent
cloths and socks can also be used to help keep
lhe oreos cleon. Addlllonol cleonup moy be
done with appropriate detergents or chemical
cleaners.
Inhalation
Eoch heollronsler Nuld chemlslry con be dll-
ferent, so learn about the unique requirements
of each one from the suppliers literature. Key
concepts to avoid unnecessary exposure to
uid vapors are the following:
* Cooler Nuld hos lower vopor pressure, ond
provides less exposure
* Slond upwlnd ol lhe somple porl durlng
ushing and sampling
* Ploce o lld over lhe somple porl Nush buckel
when nished
* Promplly cop ond seol lhe somple bollle
once lled
For producls conlolnlng componenls lhol hove
established airborne-exposure limits, consult
with an industrial hygiene technician about the
need for respiratory protection. In many cases,
proper job planning and sample cooling may
eliminate the need for respiratory protection.
Finishing the job well
Mow lhol lhe somple hos been collecled, ll
is ready for packaging and shipment to the
laboratory for analysis. While most organic
heat-transfer uids are not regulated for
lronsporl by lhe .S. Depl. ol lronsporlollon
[Voshlnglon, D.C., www.dol.gov| lor somple
quantities, the bottle should be packed prop-
erly so that it remains leak- and damage-free
until it arrives at its destination.
Bottles should be protected against break-
age. Metal containers offer the greatest
resistance, and glass containers will require
odequole pocklng molerlols. Precoullons
against container leakage can include the
following actions:
* Ensure oll seols ore properly ln ploce ln lhe
neck and mouth of the bottle
* Do nol use subslllule porls lor llquld seols
* Apply lope lo lhe oulslde ol lhe llghllyseoled
container cap
* Ploce lhe bollle wllhln o chemlcolly compol-
ible bag, which is then closed to prevent
liquid escape into the outer package
* Foom pocklng [prelormed, or peonuls"|
can be placed around the sample container
to protect it against sharp blows
* Properly dlspose ol Nuld collecled ln lhe
sample-port ush bucket
References
1. lhermlnol lnlormollon Bullelln #2: lnse
lesllng ol lhermlnol Heol lronsler Flulds. Pub.
#Z23P112C, Solullo lnc., o subsldlory ol Eosl-
mon Chemlcol Co.
2. Llquld Phose Deslgn Gulde" Pub. #lF04,
,14, Eoslmon Chemlcol Co.
Editors note: The content for this column was pro-
vlded by Eoslmon Chemlcol Co. [Klngsporl, lenn.,
www.eoslmon.com|.
Eoslmon ond lhermlnol ore lrodemorks ol Eoslmon
Chemlcol Co. or lls subsldlorles.
Safe Sampling of
Heat-Transfer
Fluids
DISCLAIMER: Allhough lhe lnlormollon ond recommendollons sel lorlh hereln ore presenled ln good lollh, Eoslmon Cheml-
col Co. ond lls subsldlorles moke no represenlollons or worronlles os lo lhe compleleness or occurocy lhereol. You musl
make your own determination of suitability and completeness for your own use, for the protection of the environment and
lor lhe heollh ond solely ol your employees ond purchosers ol your producls. Molhlng conlolned hereln ls lo be conslrued
as a recommendation to use any product, process, equipment or formulation in conflict with any patent, and we make no
represenlollons or worronlles, express or lmplled, lhol lhe use lhereol wlll nol lnlrlnge ony polenl. MC REPRESEMlAllCMS
CR VARRAMllES, EllHER E/PRESS CR lMPLlED, CF MERCHAMlABlLllY, FllMESS FCR A PARllCLAR PRPCSE, CR
CF AMY ClHER MAlRE ARE MADE HEREMDER VllH RESPECl lC lMFCRMAllCM CR lHE PRCDCl lC VHlCH
lMFCRMAllCM REFERS AMD MClHlMG HERElM VAlVES AMY CF lHE SELLERS CCMDlllCMS CF SALE. Solely Dolo
Sheets providing safety precautions that should be observed when handling and storing our products are available online
or by requesl. You should obloln ond revlew ovolloble molerlol solely lnlormollon belore hondllng our producls. ll ony
materials mentioned are not our products, appropriate industrial hygiene and other safety precautions recommended by
their manufacturers should be observed.
1,4-Butanediol from
Bio-Succinic Acid
T
he compound 1,4-bu-
tanediol (BDO) is a
versatile intermediate
for the chemical industry. Its
largest derivative product is
tetrahydrofuran (THF), which
is used to make spandex
bers, resins, solvents and
printing inks. The second larg-
est product is polybutylene
terephthalate (PBT), which
is used to make high-perfor-
mance materials, electronics
and automotive equipment.
BDO can be produced from different tech-
nologies and raw materials. The conventional
method for manufacturing BDO is the Reppe
process, starting from acetylene. Other pro-
cesses use propylene oxide, maleic anhydride,
1,3-butadiene or n-butane as starting points.
The newest technologies being developed for
BDO are bio-based pathways, which mostly
rely on bio-based succinic acid derived from
biomass or a sugar substrate.
Succinic acid is a platform chemical that can
be used to produce many products. However,
its high cost of production from petroleum raw
sources limits its use to specic applications
(such as pharmaceuticals and food additives).
According to the U.S. Dept. of Energy (DOE),
bio-succinic acid is a renewable building-block
chemical with great potential for the future.
The process
The process depicted in Figure 1 was compiled
based on a U.S. patent published by BioAmber
Inc. (Montreal, Canada; www.bio-amber.com;
U.S. patent no. 2011/0245515). The patent
discloses details about the initial reaction,
while the separation process was conceived by
Intratec and is based on well-known practices.
Hydrogenation reaction. A solution of bio-
succinic acid in water is pre-heated and sent to
the xed-bed hydrogenation reactor. Hydrogen
is compressed and also fed in excess to the
reactor. The process uses a bimetallic catalyst
consisting of metals (including ruthenium, rhe-
nium, tin and others) on a carbon support.
The exothermic reaction product is mostly
BDO (selectivities to BDO of more than 90%
are reported in literature). Side products include
THF, gamma-butyrolactone (GBL), and linear
alcohols (n-butanol, n-propanol). The amount
of each product depends on the catalyst and
operational conditions used.
The bio-succinic acid is totally reacted,
and the unreacted hydrogen is compressed
and recycled back to the reactor. The product
stream is cooled and sent to ash vessels to
recover unreacted hydrogen and eliminate
volatile materials.
Purication. The product from the ash vessels
is sent to a series of distillation columns to
separate BDO from side products. In the rst
column, BDO, GBL and water are removed
from the bottoms and then sent to the drying
column, where most of the water is removed.
The columns top fraction is sent to a lights
column, to recover side-products as fuel.
The recovered water is sent to a tank for fur-
ther disposal or to be recycled to an integrated
bio-succinic acid production unit (see Figure
2). The drying columns bottoms are sent to a
BDO recovery column and further to a heavies
column, where a stream of 99.5 wt.% BDO is
nally achieved.
Economic performance
An economic evaluation of the process was
conducted based on data from the fourth quar-
ter of 2013. The following assumptions were
taken into consideration.
* A ,000lon,yr BDC producllon unll [lhe
process equipment is represented in Figure 1)
* Sloroge copoclly equol lo 20 doys ol opero-
tion for BDO and no storage for bio-succinic
acid
The estimated capital investment (including
total xed investment, working capital and
other capital expenses) to build a plant would
be $100 million in the U.S. Gulf Coast region
and $140 million in Brazil.
Process perspective
It may be an interesting consideration to
control the entire supply chain through the
integration of a bio-succinic-acid production
unit with a BDO unit (see Figure 2). Also, the
bio-BDO produced must include a premium
price over its petrochemical counterpart. Both
measures are important to make the venture
economically feasible.
In addition, it is also an important research-
and-development goal to nd hydrogenation
catalysts that have the following qualities:
* lmproved loleronce lo lmpurllles generoled ln
the fermentation process (that produces bio-
succinic acid). This can help reduce the costs
of bio-succinic acid purication
* lncreosed selecllvlly ol blosucclnlc ocld lo
BDO, reducing the formation of side products
and the costs with BDO purication
Both achievements can reduce investment and
production costs.
Editors Note: The content for this column is
supplied by Intratec Solutions LLC (Houston; www.
intratec.us) and edited by Chemical Engineering.
The analyses and models presented herein are
prepared on the basis of publicly available and
non-confidential information. The information and
analysis are the opinions of Intratec and do not
represent the point of view of any third parties.
More information about the methodology for
preparing this type of analysis can be found, along
with terms of use, at www.intratec.us/che.
Bio-succinic acid in water
ST
Hydrogen
Lights
as fuel
CW
CW
Water for
disposal or
recycle
Heavies
BDO
1
2
3
ST
CW
9
10
1) Hydrogenation reactor
2) High-pressure vessel
3) Low-pressure vessel
4) High-pressure column
5) Light-ends column
6) Drying column
7) BDO recovery column
8) Heavies column
9) Cooling tower
10) Boiler
CW Cooling water
ST Steam
CW
ST
4
CW
ST
6
CW
ST
7
CW
ST
8
CW
ST
5
Offgas
Lights
Milling,
treatment and
sugar inversion
Sugarcane
Fermentation
Cell separation,
recovery and
purication
Hydrogenation
reaction
Purication BDO
Water
Bio-
succinic
acid
Corn
Milling and
saccharication
Glucose
Hydrogen
Bio-succinic acid unit 1,4-Butanediol unit Biomass source unit
Heavies
or
By Intratec Solutions
FIGURE 2. It is possible to integrate 1,4-butanediol and bio-succinic-acid production units
FIGURE 1. The 1,4-butanediol process from bio-succinic acid that is shown here
is based on patent disclosures from BioAmber and well-known practices
W
ater and wastewater treat-
ment are extremely im-
portant at liquefied natu-
ral gas (LNG) facilities
and other industries that are blos-
soming due to the shale-gas boom.
Engineering concerns are similar
to those of other industrial water-
treatment and power-generation
systems, but with the added issue
of adequate treatment for entrained
hydrocarbons. With proper system
design and operation, plant person-
nel can plan for, and react to, issues
that could otherwise cause unit
shutdown, environmental hazards
or safety problems.
The enormous growth in shale-
gas production has led to an expan-
sion in the number of LNG distri-
bution facilities in the U.S. These
facilities require power and steam
to compress and cool incoming nat-
ural gas, and also to scrub the gas
of impurities that would otherwise
interfere with the liquefaction pro-
cess. Economically, it is often logi-
cal to use a portion of the incoming
natural gas as a source of energy for
onsite combined-cycle power and
steam generation.
However, a number of specific
engineering challenges confront
personnel who must work with
makeup water, process water and
wastewater treatment for such
complex and integrated facilities.
Many of the water-treatment pro-
cesses discussed in this article are
also applicable to other industries
that are benefitting from the shale
gas boom, such as production facili-
ties for ammonia and urea, ethylene
and other petrochemicals.
Processing natural gas
Natural gas is primarily composed
of methane (CH
4
), but the methane
content is never 100%. Rather, im-
purities typically exist in most nat-
ural gas supplies (Table 1).
Ethane, heavier hydrocarbons
and impurities must be removed to
ensure successful production and
delivery of the required end prod-
uct. The impurities will negatively
impact the liquefaction process, and
some may cause corrosion in the
equipment. Figure 1 shows many
of the fundamental unit processes
that are used to treat natural gas
prior to LNG production.
The acid-gas scrubber typically
uses an aqueous amine solution
to remove carbon dioxide and sul-
fur compounds. This is followed by
dehydration to remove water that
would otherwise freeze during liq-
uefaction. Next is a heavy-hydro-
carbon-recovery unit (HRU), which
extracts ethane and other higher
hydrocarbons (these are recovered
for further processing). It should
be noted that ethane is becoming
an increasingly popular feedstock
for ethylene production, with a new
technology oxidative dehydroge-
nation gaining interest as an al-
ternative to standard cracking [2].
The remaining steps in LNG prepa-
ration are liquefaction and nitrogen
stripping to produce the final liquid
product for storage.
The waste- and product-recovery
streams from the LNG-production
facility are typically treated in
various heat exchangers and other
unit operations. Among the sev-
eral water and wastewater streams
around the plant, the following are
very likely:
HIgh-purIfy makoup wafor Ior
the power- and steam-production
units. A water-cooled thermal oxi-
dizer may also be present to de-
stroy some organics
Makoup wafor Ior fho amIno soIu-
tion for acid-gas scrubbing
Rocovorod wafor Irom fho dohy-
dration unit
Rofurnod condonsafo Irom ofhor
unit processes, including heavy-
hydrocarbon recovery
Makoup wafor Ior a possIbIo cooI-
ing tower
Treating each of these streams pres-
ents new challenges beyond those of
standard water purification.
Makeup water treatment. Com-
mon for new LNG plants and re-
lated facilities, such as petroleum
refineries and petrochemical plants,
is high-pressure steam generation,
often with auxiliary power pro-
duction. Ensuring proper makeup
water treatment for this process is
critical [3]. For high-pressure steam
Feature Report
46 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Cover Story
Brad Buecker and Brian Clarke
Kiewit Power Engineers
LNG and other facilities that are expanding
due to the shale-gas boom face specific
challenges when it comes to ensuring the
purity of the inlet and outlet water
Raw
gas
Acid gas
scrubber
Dehydration
unit
Heavy
hydrocarbon
recovery unit
Pre-cooling and
liquefaction units
Nitrogen
stripper
LNG
storage
Part 1
FIGURE 1. The major unit operations involved in the treat-
ment of natural gas for conversion to LNG are shown here.
In order, the processes remove acid gases and sulfur, water,
heavy hydrocarbons and nitrogen
Modern Water-Treatment
Challenges
generation, high-purity makeup
water must be supplied to the unit.
Even slight concentrations of impu-
rities can cause major corrosion and
fouling problems within a steam
generator, due to the high tempera-
tures and pressures. As an example,
the Electric Power Research Inst.
(EPRI) has established guidelines
(shown in Table 2) for makeup to
combined-cycle heat recovery steam
generators (HRSGs).
To produce water with such high
purity, a step-wise process must be
employed. Following the removal
of large solids via settling, screens,
or both, many industrial applica-
tions now also carry out micro- or
ultra-filtration (MF and UF, respec-
tively), followed by two-pass reverse
osmosis (RO), with final polishing
carried out by either mixed-bed
ion exchange or electrodeionization
(EDI). Additional details on these
processes may be found in Ref. 3.
Heavy industrial plants typically
require a large volume of water for
cooling and makeup water produc-
tion. Often, the amount of water
needed for steam production is
small compared to cooling water
needs. This is particularly true if a
large percentage of the steam is re-
covered as condensate and returned
to the boilers. For low-volume needs,
a freshwater source may be avail-
able for makeup. However, makeup
for industrial cooling towers typi-
cally requires flowrates of several
thousand gal/min or more, most of
which leaves the towers as evapora-
tion. To meet this demand, facilities
are increasingly being mandated to
use less-than-pristine supplies for
such high-volume inlet water.
These sources include reclaim
water from municipal wastewater-
treatment plants and groundwater
with high dissolved-solids content.
For the former source, problem con-
stituents that may arise include
elevated levels of ammonia, phos-
phorus and suspended solids, all of
which can be problematic in cooling
towers. Excessive suspended solids
increase the potential for deposi-
tion in cooling tower fill and other
locations in the cooling system. Am-
monia reacts irreversibly with chlo-
rine, making chlorine-based biocide
programs less effective. Microbio-
logical fouling can create a range of
problems within cooling systems.
Meanwhile, phosphorus in the
makeup stream presents multiple
problems. For decades, a common
cooling-tower treatment method has
been based upon a core chemistry of
inorganic and organic phosphates,
with minor additions of other chem-
icals to manage corrosion and scale.
However, excess phosphorus in the
makeup water can throw such pro-
grams completely out of range. And
another emerging problem is over-
shadowing this issue in many areas
of the country. The issue is phos-
phorous impairment (a condition
recognized by the U.S. Geological
Survey) of receiving bodies of water.
More and more frequently, phospho-
rus discharges are being limited or
banned due to their potential to pro-
mote toxic algae blooms [5]. In fact,
this issue had led to the develop-
ment of, and demand for, non-phos-
phorus, cooling-water-treatment
programs, in which only polymers
are utilized for scale control [6].
Condensate return. In a typical
power plant arrangement, virtu-
ally all of the steam that passes
through the turbine is recovered
and returned to the steam genera-
tor. Losses due to minor leaks and
evaporation may consume one or
two percent of the stream, but the
vast bulk of purified water is con-
tinually recovered. At chemical
process plants, much of the steam
serves process heat exchangers and
reaction vessels. Thus, there is sub-
stantial opportunity for the conden-
sate to become contaminated.
Per the nature of this article, we
will focus on organic contamination
and start with an illustrative case
example. A number of years ago,
author Buecker and a colleague
were called to an organic chemicals
plant that produced phenol deriva-
tives. At the time of the visit, the
plant had four 550-psig boilers with
superheat. Plant personnel had to
regularly replace the superheater of
each boiler every 1.5 to 2 years due
to extensive solids deposition and
subsequent tube overheating.
An initial visual inspection showed
foam in the boiler drum sample
lines. Subsequent research indi-
cated frequent high concentrations
of organic carbon in the condensate
return, sometimes as great as 200
parts-per-million (ppm). AMSE in-
dustrial boiler guidelines [7] recom-
mend a total organic carbon (TOC)
limit of 0.5 ppm for steam genera-
tors of this pressure. Although this
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 47
TABLE 1. CONSTITUENTS IN
NATURAL GAS SUPPLIES, %*
Source (State)
Components PA SC OH LA OK
Methane 83.4 84.0 93.3 90.0 84.1
Ethane 15.8 14.8 5.0 6.7
Carbon dioxide 0.7 0.2 0.8
Nitrogen 0.8 0.5 3.4 5.0 8.4
Hydrogen sulfide 0.2
*Abridged from original table in Ref. 1
TABLE 2. MAKEUP WATER REQUIREMENTS
FOR HRSGS
Constituent or measurement Normal limit
Chloride 3 parts-per-billion (ppb)
Silica 10 ppb
Sodium 3 ppb
Specific conductivity 0.1 S/cm
Sulfate 3 ppb
Total organic carbon (TOC) 300 ppb
Source: Reference 4
To flare
system
HP
flash
tank
Flash
tank
Deaerator
Feedwater
to boiler
HP cond
return
LP cond
return
To flare
system
Steam
turbine
cond
DA
vent
FIGURE 2. Shown here is one possible treatment scheme to re-
move impurities from the LNG-condensate return. The process re-
moves combustible materials from the condensate return followed
by any excessive dissolved oxygen that may exist. Ideally, the
boiler feedwater should contain a small dissolved oxygen residual
concentration of 5 to 10 ppb to inhibit fow-accelerated corrosion
Cover Story
48 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
case example may seem ex-
treme, the point is that organic
contamination can create a host
of problems. For high-pressure
steam generators of 2,000 psig
or greater, the recommended
TOC limit in the condensate is
200 ppb. This guideline aims to
reduce the transport of organics
to the boiler and carryover to the
steam, particularly in high-pres-
sure units, since this results in
decomposition of these materials
to small-chain organic acids. The
acids may cause corrosion in steam
turbines and condensate systems.
For LNG facilities (Figure 1), the
potential impurities that can enter
the condensate include residual
amine from the acid-gas scrub-
ber, and hydrocarbons from HRU
and from fuel gas heaters that are
not shown on the figure. One con-
figuration that has been developed
for volatile-compound removal is
shown generically in Figure 2.
The process relies on flash tanks
and conventional deaeration to re-
move the volatile impurities that
may be in the condensate. Some
streams from the amine-scrubbing
system are at high pressure, and
these are treated in the HP flash
tank. Other, low-pressure (LP)
streams, including condensate from
heavy-hydrocarbon heat exchang-
ers, enter the main flash tank. This
stream combines with condensate
recovered from the power plant
steam turbine for final condition-
ing in the deaerator. This particu-
lar process relies on the volatility
of the impurities. At other facilities
where heavier hydrocarbons and oil
could be in the condensate, other
techniques such as steam-driven
stripping or condensate polishing
using activated carbon or adsorbent
resin may be required.
Another concern regarding
condensate return is the poten-
tial transport of piping corrosion
products to the steam generator.
Straightforward particulate matter
filtration might be the answer in
some cases, but in others, the use of
powdered-resin condensate polish-
ing may be appropriate to achieve
greater removal of particulates.
Cooling water. The authors and
many others have discussed cool-
ing-water treatment methods in nu-
merous publications. But, there are
several cutting-edge aspects of cool-
ing water that bear further exami-
nation. Perhaps most important to
future system design are the pend-
ing 316b regulations from the U.S.
Environmental Protection Agency
(Washington, D.C.). These guide-
lines have been developed to protect
aquatic creatures at plant intakes.
The ultimate effect of the guidelines
is to eliminate once-through cooling.
As discussed in Ref. 8, to meet these
requirements, cooling towers, and
to a lesser extent air-cooled con-
densers (ACC), are now the choice
for new facilities. As we have pre-
viously commented, cooling tower
chemistry is becoming more com-
plex, particularly at plants that ei-
ther accept less-than-fresh makeup
water or have tough restrictions on
cooling-tower discharge.
The list that follows outlines po-
tential treatment and control tech-
nologies that can be used to deal
with difficult makeup streams for
cooling tower systems.
!or sysfoms whoro phosphafo/
phosphonate chemistry is pres-
ently used or is desired, selection
of reclaim water for makeup might
require installation of a clarifier
to remove incoming phosphorus
compounds. Iron and aluminum
coagulants will precipitate phos-
phate. Jar testing and pilot test-
ing are a must for developing the
proper treatment scheme
AmmonIa In makoup wafor can
be removed by breakpoint chlori-
nation, but for high-volume flows
(such as cooling towers), this sce-
nario may be a cost-prohibitive
technique. Ammonia stripping
may be a necessary option
Somo pIanfs now havo makoup
water coming from deep wells.
This water often contains high
concentrations of hardness, bicar-
bonate alkalinity, chloride, silica
and others. To remove hardness
ions and alkalinity, lime and soda
ash softening may be required,
with possible supplemental mag-
nesium feed for silica reduction.
Chlorides can wreak havoc on
stainless steels, so more exotic
materials may be needed for heat
exchangers
CooIIng-fowor-sIdosfroam IIIfra-
tion is always beneficial in reduc-
ing the suspended-solids concen-
tration in the circulating water.
Cooling towers are also effective
air scrubbers, capturing particu-
late matter that may enter from
the atmosphere, and particulate
matter that enter via the makeup
stream. Typically, a sidestream
filter is designed to treat from
310% of the total circulating
water flow
!so oI subsfandard makoup wafor
requires very careful selection
of the biocide treatment system.
Microbiological fouling can occur
very rapidly in a cooling system,
with severe consequences. In fact,
cooling towers have been known
to collapse due to the weight of
microbiological deposits. Chlorine
will be immediately consumed
by ammonia and organics in the
water, and this can plague systems
using reclaim water. Becoming
more popular for reclaim-water
Raw
water
Service
water
Plant
drains
collection
Oil/water
separator
Wastewater
tank
To
WWTP
From sumps and equipment
drains containing
hydrocarbons and oil
Main
boiler
Auxiliary
boiler
Auxiliary
boiler
blowdown
tank
Main
blowdown
tank
Vent
Vent
Raw
water
storage
Demineralizer
Demin-
eralizer
water
storage
To
process
Demineralizer
reject and
regeneration
waste streams
Steam to process
FIGURE 3. Shown
here is a generalized
water-treatment sche-
matic (excluding the
cooling tower) for an
LNG-production facility.
A common demineral-
izer arrangement is
reverse osmosis to
remove >99% of dis-
solved ions, followed
by ion exchange polish-
ing to remove residual
ions. Pre-treatment to
remove suspended sol-
ids is not shown
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 49
microbiological treatment is chlo-
rine dioxide (ClO
2
). This product
must be generated on-site and is
more expensive than bleach, but
it does not react with ammonia
and is not consumed by standard
organics
Even with these technologies in
place, the wastewater produced
during LNG production still needs
proper treatment.
Wastewater. Cooling-tower blow-
down is often the largest wastewa-
ter stream at heavy
industrial facilities,
and at LNG plants,
petroleum refiner-
ies, petrochemical
plants and similar
facilities. At many
plants, the blow-
down is released to
a receiving body of
water, provided the
discharge meets the
plants National Pollutant Discharge
Elimination System (NPDES) guide-
lines. However, this option is becom-
ing more limited for many process
operators [8].
Excluding the cooling tower, a ge-
neric water balance at an LNG fa-
cility with power generation might
closely resemble Figure 3. The unit
operations are not shown in elabo-
rate detail in Figure 3, but the ob-
jective is to provide a system over-
view. The process shown is similar
to that of a typical natural-gas-
fired, combined-cycle plant, with a
few exceptions. The large bulk of
the makeup water goes toward pro-
duction of steam for process use and
as a source of demineralized feed
to the process. The aqueous amine
used for acid-gas scrubbing needs
regular replenishment. As seen in
this particular design, plant and
process drains are treated in an oil-
water separator (OWS) prior to fur-
ther treatment. The OWS stream
combines with boiler blowdown and
demineralizer waste in the waste-
water tank, from which the liquid is
forwarded for further processing.
One possibility for wastewater
treatment is to remove non-volatile
impurities as solids and recycle the
distillate, as shown in Figure 4.
Evaporator-crystallizers are com-
monly used in the chemical process
industries, with proven success. A
deaerator is typically installed up-
;
Distilled water
to process
Distilled water
to process
Feed from
wastewater
tank
Evaporator
concentrate
tank
Filter press
or other sludge
thickener
Crystallizer
Solids
to disposal
Evaporator
FIGURE 4. Shown here is an evaporator-crystallizer sche-
matic for wastewater treatment. This process, or variations
thereof, allow the plant to operate with zero liquid discharge
Ensure your
piping integrity
In todays operating environment, its more
important than ever that the piping within
your Mechanical Integrity Program complies
with standards such as API-570 and API-574.
Quest Integrity offers a comprehensive solution
for piping circuits using our proprietary,
ultrasonic-based intelligent pigging technology
combined with LifeQuest Fitness-for-Service
software.
Ensure your piping integrity by identifying
degradation before loss of containment occurs.
www.QuestIntegrity.com/CE
+1 253 893 7070
A TEAM Industrial Services Company
100% inspection of
internal and external
pipe surfaces
Inspection results
tailored to comply with
API-570 and API-574
LifeQuest Fitness-
for-Service results
tailored to comply with
API-579
Circle 40 on p. 76 or go to adlinks.che.com/50980-40
Circle 41 on p. 76 or go to adlinks.che.com/50980-41
V
i
s
i
t

u
s

a
t

S
t
a
n
d

2
2
1
5

i
n

H
a
l
l

4

-

P
O
W
T
E
C
H

2
0
1
4
Cover Story
50 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
stream of the evaporator-crystal-
lizer, and as previously discussed,
will remove some hydrocarbons, al-
though miscible compounds such as
glycols would probably not come out
of the water phase as easily as non-
polar materials. The same consider-
ations mentioned earlier regarding
hydrocarbon carryover from the
liquefaction process apply to waste-
water treatment, and become even
more critical as the wastewater be-
comes more concentrated.
One drawback to evaporator-
crystallizers is the significant en-
ergy that is required for evaporat-
ing large quantities of water. An
alternative possibility see Ref.
8 is a process that combines fil-
tration, softening and reverse osmo-
sis, which can reduce the discharge
volume to be treated by 90%. This
leaves a relatively small stream to
be further processed by a crystal-
lizer or other method.
Edited by Suzanne Shelley
Bellacide 355 puts your cooling
tower back in control, and
Bellacide 301 economically
keeps you there. When used
with a halogen, Bellacide
creates a highly potent
biocide treatment to improve
microbiological performance
and reduce total costs.

Clean up cooling tower water
problems with new power to de-
crease total costs.
Contact us today:
[email protected]
[email protected]
[email protected]
[email protected]
www.wateradditives.com
Bellacide

355/301
Get clean / Keep clean biocides
Powerful,
clean,
economical.
Circle 13 on p. 76 or go to adlinks.che.com/50980-13
Authors
Brad Buecker is process
specialist in the Environ-
mental Services group of Kie-
wit Power Engineers (9401
Renner Blvd., Lenexa, KS
66219; Phone: 917-928-7311;
Email: brad.buecker@kiewit.
com). The group provides
consulting and engineering
for industrial water, wastewa-
ter and air-pollution-control
projects. He has more than
33 years of experience in the power industry,
much of it with City Water, Light & Power in
Springfield, Ill., and at Kansas City Power &
Light Companys La Cygne, Kan., generating
station. Buecker has written many articles and
three books on steam generation topics, and he
is a member of the American Chemical Society,
AIChE, the American Soc. of Mechanical Engi-
neers, the Cooling Technology Institute, and the
National Assn. of Corrosion Engineers. He has
a B.S. in chemistry from Iowa State University,
with additional course work in fluid mechanics,
heat and material balances, and advanced inor-
ganic chemistry.
Brian Clarke is a water and
wastewater project manager
in the environmental services
group of Kiewit Power En-
gineers (KPE; 9401 Renner
Blvd., Lenexa, KS 66219;
Email: brian.clarke@kiewit.
com). He is a professional
engineer, licensed in Ohio.
Clarke graduated in 2004
from Ohio University with a
B.S.Ch.E. After graduating,
he worked in data analysis and consulting en-
gineering before transitioning to KPE, where he
has focused on the design of water and wastewa-
ter systems for power-generation facilities.
References
1. Stultz, S.C., and Kitto, J.B., Steam Its
Generation and Use, 40th Ed., The Babcock
& Wilcox Co., Barberton, Ohio, 1992.
2. Oxidative Dehydrogenation of Ethane to
Ethylene, accessed at: www.itcp.kit.edu/
deutschmann/img/content/od_habil_ii.pdf
3. B. Buecker, Modern Concepts in Makeup
Water Treatment, Chem. Eng., November
2011.
4. Cycle Chemistry Guidelines for Com-
bined Cycle/Heat Recovery Steam Genera-
tors (HRSGs), EPRI, Palo Alto, CA: 2006.
1010438.
5. Wisconsin to Expand List of Water Bodies
Under Phosphorus Pollution Threat, Pro-
cessing e-newsletter, February 20, 2014.
6. Post, R., Development and Application of
Phosphorus-Free Cooling Water Technol-
ogy, Cooling Technology Inst. Annual Winter
Meeting, February 36, 2014, Houston.
7. Consensus on Operating Practices for
the Control of Feedwater and Boiler Water
Chemistry in Modern Industrial Boilers,
The American Society of Mechanical Engi-
neers, New York, NY, 1994.
8. Buecker, B., Cooling Towers: Dealing with
Tighter Cooling Water Regulations, Chem.
Eng., Aug. 2014, pp. 5760.
Cover Story
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 51
O
perators and engineers in the
chemical process industries
(CPI) who are responsible for
the daily operations associ-
ated with sludge dewatering and
drying equipment are undoubt-
edly aware that wastewater-sludge
drying is not an easy task. A large
number of the problems that arise
during these operations are due to
the sticky phase of sludge, which
makes the drying of sludge as
much an art as a science. Although
insight into the sticky behavior
of sludge during drying processes
is critical for successfully drying
sludge in practice, the sticky phase
of sludge is not a common topic in
the standard engineering curricu-
lum at universities and colleges,
whereas topics such as the theoret-
ical design of dryers typically are.
Also, most research papers and ref-
erence works on sludge drying tend
to emphasize the different types
of sludge dewatering and drying
technologies [1,2], rather than the
physical property changes that the
sludge undergoes while being re-
duced in volume due to water re-
moval. The sludges sticky charac-
ter is typically mentioned in just a
few lines, without elucidating the
reasons behind its existence. Ref-
erence 3, (a paper with the appro-
priate title Can You Handle Sticky
Cakes?,) concludes that difficul-
ties in solid-liquid separations
usually arise because conventional
design optimizes only the unit op-
erations and takes no account of
the nature of the thickened prod-
uct or possible handling problems
[3]. This assessment applies well to
the case of sludge dewatering and
drying. Providing more insight into
the peculiar sticky phenomenon
of sludge is the aim of this article.
Further, an overview of applied
strategies to tackle the operational
issues related to the sludges glu-
eyness will be provided.
Growing mountains of sludge
Increasingly stringent environmen-
tal regulations over time have re-
sulted in enhanced industrial and
domestic wastewater treatment
(see, for example, Chem. Eng. Oct.
2005 and Oct. 2013 issues [4,5]). The
improved wastewater treatment
has resulted, in turn, in increased
volumes of waste activated sludge.
In a recent review paper on the ap-
plication of wastewater-sludge dry-
ing, some data are presented on the
quantities of generated municipal
sewage sludge, illustrating these
increasing mountains of sludge.
In China, more than 9 million tons
of dry solid sludge were produced
in 2009. In the European Union
and the United States, this number
amounted to about 12 and 8 million
tons in 2010, respectively [6].
To lower the sludge volumes (in
order to decrease costs for further
downstream processing, including
transport, storage and incinera-
tion costs), mechanical dewatering
and thermal drying of sludge are
important onsite unit operations in
CPI wastewater treatment plants
(WWTPs). Sludge management in
industrial sludge-handling instal-
lations is, and will continue to be, a
challenge, and sticky phase of sludge
is an issue common to all.
The sticky phase of sludge
When sludge is partially dewatered,
it behaves as a sticky, paste-like
substance. In that state, it liter-
ally glues onto the surface of the
dewatering and drying equipment.
In order to gain insight into the
stickiness of sludge, the authors of
this article developed a laboratory
Feature Report Cover Story
Bart Peeters, Monsanto Europe
Raf Dewil and Ilse Smets,
KU Leuven BioTeC
In wastewater-sludge drying
and dewatering operations,
many issues arise from the
sticky properties of the sludge.
Here are some insights to address them
Challenges of Drying
Sticky Wastewater Sludge
Part 2
FIGURE 1. A rather simple laboratory
protocol can be used to map the sticky
phase of waste sludge (see Ref. 7)
Cover Story
52 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
protocol that allows its
visualization. For de-
tails on the protocol, see
Ref. 7. In short, a rather
simple laboratory device
(Figure 1) measures the
shear stress necessary
for letting pre-consol-
idated sludge (with a
certain composition)
start moving over a steel
surface. A higher shear
stress requirement in-
dicates that the sludge
is stickier [7,8]. By plot-
ting the shear stress as
a function of the sludge
dry-solid percentage
(%DS), one obtains a
map of the sticky behav-
ior. In Figure 1, a sludge
sample is shown after it
was tested, along with the cylinder
where this sludge sample was con-
tained during the shear test.
The mapping of the stickiness is
shown in Figure 2 for five different
sludges from the Monsanto WWTP
in Antwerp, Belgium. The organic
contents vary from 49% for sludge
1 to 30% for Sludge 5 (the organic
fraction was analyzed according to
the standard methods [9]). The data
depicted in Figure 2 suggest that the
sludges sticky character depends on
both the sludges dryness and its or-
ganic content. Considering Sludges
1 and 2, samples behave most sticky
in the dryness range from 2540%
DS. Therefore, this dryness region
is called the sticky phase of slud-
ges 1 and 2 [7]. Likewise, the sticky
phase of Sludges 3 and 4 is in the
dryness region from 3560%DS. For
Sludge 5, the sticky phase reaches
from about 4560% DS.
These data support the concept
that the sticky phase appears in
a particular dryness region (often
cited in literature sources), but that
the exact location of the sticky re-
gion depends on the characteristics
of the sludge, as exemplified by the
different curves in Figure 2.
Some room for error is thus very
much justified in the interpretation
of the data provided in literature
sources. Moreover, instead of using
this information, engineers might
do better to take the plunge and
map the sticky phase for the sludge
in their own facilities.
The reason why the sticky phase
occurs at higher dryness for sludge
with a lower organic content will be-
come clear after we have explained
the (proposed) mechanism for the
sticky phenomenon of sludge [10].
An understanding of why sludge
should behave in such a sticky man-
ner during the course of drying be-
gins with a look at activated sludge
as a matrix of long biopolymers
(such as extracellular polymeric
substances EPS) wherein the mi-
croorganisms are entrapped [11,12].
In other words, in the context of
explaining the physical property
changes of drying sludge, we think of
sludge as a kind of biopolymer ma-
trix whereby the biopolymers glue
together the microorganisms of the
sludge. The central role of the EPS
in the sludge floc structure was also
highlighted in Chemical Engineering
[13]. During dewatering and drying,
the gluing biopolymers become more
and more concentrated and a sticky
mixture develops. Keeping in mind
the concept of a biopolymer solution,
the stickiness curves for each of the
five individual sludges represented
in Figure 2 (which, in general, can
be qualitatively summarized by the
curve depicted in Figure 3) is ex-
plained as follows [10]:
1. At low sludge dryness (high water
content), the wet sludge does not
behave as a sticky substance be-
cause at that stage, it is a biopo-
lymer solution with low concen-
tration. The sludge makes loose
contact with the surfaces of the de-
watering and drying equipment (to
be compared with aquaplaning)
2. When the sludges dryness in-
creases (and water content de-
creases), the biopolymer solution
becomes more and more concen-
trated and becomes more and
more sticky until it reaches
the dryness region, wherein it be-
haves with most stickiness (this is
its sludge-specific sticky phase)
3. The quite abrupt decrease in
sludge stickiness at higher dry-
ness, just beyond the sticky phase,
is attributed to the cavities that
develop at the contact surface be-
tween the sludge and dryer equip-
ment. These cavities are a result
of the further concentration of
the biopolymer solution to such
a critical extent that the biopoly-
mers will not spread out any more
on the dryer wall to the same ex-
tent that they did at a somewhat
lower dryness. At this point, the
adhesiveness of the drying sludge
decreases spectacularly with only
small increases in dryness.
Figure 3 presents a summarizing
scheme of the sludge consistency
%DS
1
.
0
4
.
0
7
.
0
9
.
3
1
1
.
4
1
3
.
0
1
5
.
0
1
6
.
7
1
8
.
4
2
0
.
0
2
2
.
5
2
4
.
0
2
6
.
0
2
7
.
2
2
8
.
0
3
0
.
5
3
1
.
1
3
3
.
0
3
5
.
1
3
6
.
3
3
8
.
0
3
9
.
9
4
1
.
0
4
2
.
6
4
5
.
0
4
6
.
0
4
7
.
0
4
9
.
0
5
1
.
8
5
3
.
0
5
5
.
0
5
6
.
0
5
8
.
0
6
1
.
0
6
3
.
7
6
5
.
9
6
7
.
0
7
0
.
0
7
2
.
0
7
5
.
0
7
8
.
0
8
1
.
0
8
4
.
0
8
7
.
0
9
0
.
0
9
3
.
0
9
6
.
0
9
8
.
4
1
0
0
.
0
2,000
1,750
1,500
1,250
1,000
750
500
S
h
e
a
r

s
t
r
e
s
s

(
P
a
)


Sludge 1
(49% org.)
Sludge 2
(47% org.)
Sludge 5
(30% org.)
Sludge 3
(35% org.)
Sludge 4
(35% org.)
Sticky phase of Sludges 1 and 2
FIGURE 2. The sticky behavior of sludges depends on dryness and organic content (org.). There
are three repeats of the shear stress test at every %DS, and bars are the 95% confdence interval
(lines are to guide the eye). Data from Sludges 1 and 5 are adapted from Refs. 7 and 10, respectively
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 53
during its course of dewatering and
drying. For a conceptual represen-
tation of the sludge sticky behavior,
see Ref. 10.
This brings us back to the ques-
tion raised above that is, why does
sludge with a lower organic content
have its sticky phase at higher dry-
ness levels? Lower organic content
of the sludge (as a result of a tempo-
rarily higher amount of precipitated
CaCO
3
salts in the sludge floc be-
cause of changing wastewater com-
position, for example [14]) implies a
lower EPS content per unit mass of
sludge. Again keeping in mind the
above described biopolymer matrix
of sludge, the lower EPS concentra-
tion at the start will require a more
extended dewatering or drying of
the sludge (or lower water content)
before the sludge will exhibit the
same viscoplastic behavior com-
pared to sludge with a higher EPS
concentration. The latter sludge will
already attain its maximum sticki-
ness at lower dryness.
Sticky-phase strategies
The negative effects of the sticky
phase on dewatering and drying
installations include, but are not
limited to, higher torque require-
ments in both decanter centrifuges
[10, 15, 16] and sludge paddle dry-
ers [1719], and sludge buildup on
dryer surfaces [20, 21], potentially
causing equipment damage.
To prevent these issues, strategies
applied in industry are threefold.
Two strategies aim at controlling
the sludge %DS at the beginning of
the drying stage, by either increas-
ing or decreasing the %DS, and the
third is an innovative approach
triggered by the biopolymer matrix
concept explained above:
1. A well-established method employs
back-mixing of finally dried mate-
rial into the raw (mechanically de-
watered) sludge feed stream of the
dryer. By doing so, the average %DS
in the blended feed to the dryer is
increased beyond the sticky phase
of the sludge [2, 8, 22]. As a result,
the sludge mixture becomes crum-
bly before being introduced into
the dryer, and it becomes easier to
handle. For Sludge 1 (in Figure 2),
an increase of the solids dryness
to 45% DS would suffice, as illus-
trated in the upper part of Figure
4, whereas for sludge 5, back-
mixing of dried material would be
needed to achieve about 65% DS in
the feed to the dryer
2. A less established technique in-
volves combined mechanical dew-
atering and flash-drying systems
[20, 21]. By lowering the sludge
%DS after the mechanically de-
watering stage (that is, at the
beginning of the thermal drying
stage), one postpones the timing
and place in the flash dryer where
the sludge goes through its sticky
phase. By applying this strategy
Liquid Sticky
Changes in physical consistency of sludge
Dry-dust
% DS
Dewatering / drying
S
h
e
a
r

s
t
r
e
s
s

(
s
t
i
c
k
i
n
e
s
s

a
d
h
e
s
i
v
e
n
e
s
s
)
FIGURE 3. The changes in physical consistency of waste sludge during the course
of dewatering and drying are summarized here
References
1. Isaacs, M., Heywood, N., Blake, N., Alder-
man, N., Getting a Grip on Sludge, Chem.
Eng., October, pp. 8090, 1995.
2. Chen, G., Yue, P.L., Mujumdar, A.S., Sludge
dewatering and drying, Drying Technology
20, pp. 883916, 2002.
3. Carleton, A.J., Heywood, N.I., Can you han-
dle sticky cakes?, Filtration & Separation 20,
pp. 357360, 1983.
4. An, L., Biological Wastewater Treatment: Se-
lecting the Process, Chem. Eng., October, pp.
3843, 2013.
5. Schultz, T.E., Biological Wastewater Treat-
ment, Chem. Eng. October, pp. 4450, 2005.
6. Bennamoun, L., Arlabosse, P., Lonard, A.,
Review on fundamental aspect of application
of drying process to wastewater sludge, Re-
newable and Sustainable Energy Reviews 28,
pp. 2943, 2013.
7. Peeters, B., Dewil, R. and others, Using a
shear test-based lab protocol to map the
sticky phase of activated sludge, Environ-
mental Engineering Science 28, pp. 8185,
2011.
8. Strand, A., Alsaker, J., Process and means
for drying of sticky materials, U.S. Pat-
ent 7,562,465 B2 (www.freepatentsonline.
com/7562465.pdf), 2009.
9. APHA-AWWA-WEF, Standard Methods for
the Examination of Water and Wastewater.
Washington, DC: American Public Health
Association, 2005.
10. Peeters B., Dewil R. and others, Addition of
polyaluminiumchloride (PACl) to waste acti-
vated sludge to mitigate the negative effects
of its sticky phase in dewatering-drying op-
erations, Water Research 47, pp. 3,6003,609,
2013.
11. Flemming, H.C., The perfect slime, Colloids
and Surfaces B: Biointerfaces 86, pp. 251
259, 2011.
12. Sheng, G.-P., Yu, H.-Q., Li, X.-Y., Extracellu-
lar polymeric substances (EPS) of microbial
aggregates in biological wastewater treat-
ment systems: a review. Biotechnology Ad-
vances 28, pp. 882894, 2010.
13. Peeters, B., Herman, S., Monitor Cations
in CPI Wastewater for Better Performance,
Chem. Eng. May, pp. 5662, 2007.
14. Peeters B., Dewil R. and others, Quantifica-
tion of the exchangeable calcium in activated
sludge flocs and its implication to sludge set-
tleability. Separation and Purification Tech-
nology 83, pp. 18, 2011.
15. Peeters B., Dewil R. and others, Avoiding
sludge stickiness through addition of poly-
aluminiumchloride (PACl). In: Proceed-
ings of the 11th World Filtration Congress
(WFC11), Graz, Austria (April 16-20, 2012),
paper P368, 2012.
16. Leung, W.W.-F., Torque requirement for high-
solids centrifugal sludge dewatering, Filtra-
tion.& Separation 35, pp. 883887, 1998.
17. Komline-Sanderson, Komline-Sanderson
Paddle Dryer. Drying Technology for Bio-
solids, Sludges and By-products (http://
www.komline.com/downloads/brochures/KS-
SDB_080714.pdf), 2008.
18. Arlabosse, P., Chavez, S., Lecomte, D.,
Method for thermal design of paddle dryers:
application to municipal sewage sludge, Dry-
ing Technology 22, pp. 2,3752,393, 2004.
19. Ferrasse J.H., Arlabosse, P., Lecomte, D.,
Heat, momentum, and mass transfer mea-
surements in indirect agitated sludge dryers,
Drying Technology 20, pp. 749769, 2002.
20. Peeters B., Dewil R., Smets I.Y., Improved
process control of an industrial sludge-dryer
installation through binary logistic regres-
sion modeling of the fouling issues, J. Process
Control 22, pp. 1,3871,396, 2012.
21. Peeters, B., Mechanical dewatering and ther-
mal drying of sludge in a single apparatus.
Drying Technology 28, pp. 454459, 2010.
22. Lonard, A., Meneses, E., Le Trong, E.,
Salmon, T., Marchot, P., Toye, D., Crine, M.
Influence of back mixing on the convective
drying of residual sludges in fixed bed, Water
Research 42, pp. 2,6712,677, 2008.
23. Li, H., Zou, S., Li, C. Liming pretreatment
reduces sludge build-up on the dryer wall
during thermal drying. Drying Technology
30, pp. 1,5631,569, 2012.
Cover Story
54 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Cover Story
(depicted in the middle of Figure
4), the drying sludge behaves as a
sticky paste only at a less critical
place in the dryer, such that no op-
erational issues are encountered
3. Finally, an additive can be intro-
duced into the raw sludge feed
to mitigate, or even almost com-
pletely eliminate the stickiness of
the sludge (conceptually presented
at the lower part of Figure 4). This
can be accomplished by adding
polyaluminium chloride (PACl)
a technique thoroughly tested and
validated by the authors [10, 15,
20]. The addition of rather small
amounts of PACl to the raw sludge
feed of a combined centrifuge-dryer
system (only 1020 L on a volumet-
ric sludge flow of 7 m) has become
common practice at the Monsanto
WWTP in Antwerp for more than
four years. The beneficial effect of
PACl conditioning of waste sludge
is explained by the bound hydra-
tion water associated with the su-
per-aluminium structures of PACl
solutions, attached to the exterior
of the sludge flocs upon dosing
of PACl to sludge. These shields
of hydration water act as a type
of lubrication (aquaplaning) and
guide the underlying sticky biopo-
lymers through the dryness range,
where they otherwise would cause
the sticky issues of partially dried
sludge [10]. Also lime addition pre-
treatment of sludge would reduce
the sludge buildup on dryer walls,
based on recent laboratory results
of Li and others [23].
Acknowledgments
The authors gratefully acknowledge
the mapping of the sludges sticky
phase by Luc Vernimmen from the
Monsanto Laboratory.
Edited by Scott Jenkins
Thermal
drying
%DS 2 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
Final dried
product
3) reduce sludge's intrinsic stickiness by adding PACl additive
2) lower and control solids dryness at the beginning of the drying stage by lowering
the cake dryness after mechanical dewatering to postpone and, hence, avoid
sticky issues at the beginning of the (flash) dryer
1) increase and control solids dryness at the beginning of the drying stage by
adding (recycling) final dried product to the dewatered cake, to increase solids
dryness beyond sticky phase before entrance in dryer
Mechanical
dewatering
Thermal
drying
Mechanical
dewatering
Thermal
drying
Mechanical
dewatering
Sludge
feed
Cake STICKY
PHASE
Final dried
product
Sludge
feed
Cake STICKY
PHASE
Final dried
product
Sludge
feed
Cake STICKY
PHASE
%DS 2 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
%DS 2 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
FIGURE 4. Practical control strategies to tackle sticky issues during the course of
sludge drying
Authors
Bart Peeters is a manufac-
turing technologist at Mon-
santo Europe N.V. (Haven
627, Scheldelaan 460, 2040
Antwerp, Belgium; Phone:
+32 3 568 5762; Email: bart.
peeters@monsanto. com) ,
where he has been working
since 1998. He first served
as a process improvement
engineer at Eastmans PVB
polymer manufacturing
plant on site, till 2004. Since then, he has been
working at the environmental department of
the company, with particular responsibilities in
improving the wastewater treatment plant and
the combined sludge centrifuge-dryer installa-
tion. Being a Master Black Belt he is also the Six
Sigma program leader at the Monsanto Antwerp
site. While working at Monsantos WWTP, he
obtained his Ph.D. in Engineering from the KU
Leuven (Belgium) in 2011 on the research topic
Effect of activated sludge composition on its de-
waterability and sticky phase. Prior to that, he
received his M.S.Ch.E. degree in 1998 from the
KU Leuven, plus his M.Bio.Ch.E. degree in 1996
from the university college De Nayer. He is the
author of 20 papers in scientific journals, techni-
cal magazines and international conferences.
Raf Dewil holds a M.S. Ch.E.
(KU Leuven, 2003) and a PhD
in Bioscience Engineering
(University of Antwerp, 2006).
Currently, he is an assistant
professor with the Chemical
Engineering Department of
KU Leuven, where he heads
the Process and Environ-
mental Technology Labora-
tory. Within the Faculty of
Engineering Technology of
the same university, he chairs the Sustainable
Chemical Process Technology Cluster. His main
research domains include (i) (bio)chemical con-
version methods for the valorization of biomass
and organic wastes (currently main focus on
anaerobic digestion), and (ii) the integration of
physicochemical treatment methods in waste-
water treatment (such as, advanced oxidation
processes, ultrasound, microwave). He has au-
thored or co-authored over 60 publications in
peer-reviewed international journals and about
90 presentations at international conferences.
He is an associate editor with the Journal of
Environmental Management, a member of the
editorial board of several international journals
and a regular invited speaker at international
conferences.
Ilse Smets holds a Master
in BioSciences Engineering
and a Ph.D. in Engineering:
Chemical Technology, both
of the KU Leuven (Belgium).
She is currently associate pro-
fessor at the Department of
Chemical Engineering of that
same university. She heads a
team of about eight doctoral
researchers and focuses on
monitoring, modeling and
optimization of biological wastewater-treatment
systems ranging from classic activated sludge
systems to membrane bioreactor (MBR) sys-
tems, with a specific focus on the bioflocculation
aspects of activated sludge. Her teaching activi-
ties also lie predominantly in this field. She is
a board member of B-IWA, the Belgian branch
of the International Water Association and is
the chair of the Bioprocesses and Biosystems
Technical Committee of IFAC, the International
Federation in Automation and Control. Her ac-
tive contributions to the field of wastewater
treatment, and bioprocesses in general, are fur-
ther witnessed by several review duties, many
memberships of International Programming
Committees and the co-organization of several
conferences and workshops.
We work with HEART, MIND and BODY, because we are PEOPLE
PEOPLE serving PEOPLE, with PASSION, INTELLIGENCE and COMMITTMENT
thats why we are able to offer SOLUTION PACKAGES, NOT JUST PUMPS
INGENIOUS INDUSTRIAL PUMP SOLUTIONS.
CREATED FROM BRAIN POWER
Design for excellence
Personalized guidance in the pump selection process
Fast response and delivery
Long term after market support
Trained service and spare parts available worldwide
Pompetravaini has been manufacturing industrial pump since 1929.
85 years of passionate service!
Pompetravaini Spa \|+ jer Iar||e, ++ zzz t+.t+ae |r|me (M|} Ie|. +1.11. |+\ +1.11.I
.eaa| teyjemjetr+.+| a| . | t www. jemjetr+.+| a| . | t
www.jemjetr+.+|a|.|t
Circle 39 on p. 76 or go to adlinks.che.com/50980-39
M
agnetically driven (mag
drive) centrifugal pumps
have been in use since
1947 when the first mag-
drive pump was developed. Mag
drives have always been the work-
horse pump in applications with
corrosive and often toxic fluid ap-
plications, and particularly over the
last 20 years theyve become more
common in the chemical process in-
dustries (CPI).
A typical mag-drive pump is com-
prised of a magnetically coupled
rotor-and-drive assembly separated
by a containment shell that hermet-
ically seals pumpage from the at-
mosphere (Figure 1). The mag-drive
pumps key feature is a sealless
design, which eliminates a mode of
failure. This often makes it a strong
solution for pumping applications
with mechanical seal problems.
The mag drive is commonly used to
pump hazardous and high intrinsic
value pumpage where the process
cannot or should not be diluted by
flush media (typical in a traditional
mechanical-seal pump). Mag drives
have many growing applications
in global industries, such as petro-
chemicals in petroleum refineries,
pharmaceutical applications, and
pulp-and-paper mills, which employ
caustic, acid and solvent services
during production. However, this
type of pump is somewhat under-
utilized in many of these industries
due to common misconceptions
about the technology.
Mag-drive fundamentals
Magnetically driven pumps have
several design features that extend
pump life, especially in common CPI
applications with hazardous scenar-
ios. The mag drives key design fea-
ture is the absence of a traditional
rotating mechanical seal (compare
Figure 1 and Figure 2). Instead, a
full hermetic seal with no rotating
component reduces the risk of leaks.
This sealless design is the most well-
known feature of mag drives and is
a primary reason why they are often
used for hazardous or valuable flu-
ids. Another advantage is avoidance
of mechanical seal maintenance and
flush plan maintenance.
Mag-drive pumps are available
in either ANSI or ISO dimensional
standards. They are available in
most metallurgies, as well as non-
metallic designs, such as with a
polymer lining. A polymer design of-
fers improved corrosion resistance,
utilizing polymer coatings such as
EFTE (ethylene tetrafluoroethyl-
ene). All mag drives, whether metal
or lined, have very limited solids
handling capability. The nature of
the mag-drive design has circuits
that facilitate process lubrication
of internal bearings, and these pas-
sageways are typically very small.
If solids are introduced, the circuits
can easily get blocked, leading to
pump damage. The passage ways
are sometimes so small that it will
take only a minute amount of very
small solids to erode the compo-
nents of a mag-drive pump.
Design and usage
In addition to the sealless advan-
tages, there are some key consid-
erations when deciding whether
to use a mag-drive pump. Because
they utilize magnets to transfer
power and torque from the drive
assembly to the driven rotor as-
sembly, its important to recognize
that there are temperature limita-
tions for magnets materials. When
exposed to temperatures above
their threshold they can begin to
lose their magnetism. Over time,
Feature Report
56 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Feature Report Part 1
FIGURE 1.
The main components
of a mag-drive pump
are shown in this
cross section
Magnetically Driven
Pumps: An overview
Understanding sealless pump technologies
and their potential applications
Richard Tym
ITT Goulds Pumps
Source:
ITT Goulds
Pumps
this loss of magnetism results in
pump failure due to degradation of
the magnetic coupling between the
drive and the driven component.
Therefore temperature characteris-
tics of the application are a critical
factor when considering application
of a mag-drive pump.
Another factor to weigh is the
torque limitation due to the mag-
netic coupling of the drive and com-
ponents. Its important to make sure
that the magnets are sized correctly
so magnetic-coupling breakaway
torque is not exceeded during unit
startup or steady-state operation. If
breakaway torque is exceeded, the
magnetic coupling between the drive
and the driven assemblies is lost, and
the impeller will cease to spin, which
means the pump must be shut down
to allow the magnets to recouple.
If there are numerous instances of
magnet decoupling due to improper
magnet selection or other circum-
stances, such as clogging or process
upset, magnets will degrade over
time to the point where the pump
will no longer operate properly.
In metallic mag-drive pumps,
eddy currents can also affect perfor-
mance. Eddy currents are electrical
currents generated by the motion of
the magnets moving past an electri-
cally conductive containment shell.
The inner workings of a metallic
mag-drive pump have a drive mag-
net and a driven assembly separated
by a metal barrier. As the magnets
start rotating around this barrier,
eddy currents form and generate
heat. The design of a mag-drive
pump must take into account the
removal of this heat to avoid boiling
and possible flashing or vaporizing
of process lubricants, which will
cause pump failure through bear-
ing damage. Furthermore, there is
a loss of horsepower due to eddy
currents. Eddy-current effects can
be mitigated by correct sizing of the
magnets and the motor.
A final consideration when utiliz-
ing mag-drive pumps is to be aware
that they are extremely sensitive
to dry-run and dead-head condi-
tions. In the case of dry run, a loss
of liquid in the pump system can
cause the process lubricated bear-
ings to overheat and crack, leading
to pump failure. Dead head occurs
when running the pump against
a closed valve or a blockage in the
line results in the loss of fluid cir-
culation. This results in a buildup
of heat and excessive thrust loading
that can cause unit failure.
Overview of mag-drive designs
A common misconception about
mag-drive pumps is that their de-
signs are complicated. These mis-
conceptions are based on older
mag-drive designs that commonly
had a large number of component
parts, including individual heat-
shrunk bearings, spacers and vari-
ous O-rings. More than a dozen
components were typically involved
and assembling and disassembling
required longer maintenance time.
However, the industry has made
great strides in recent years, result-
ing in newer, significantly simpler
technologies (Figure 3). Improve-
ments to bearing-cartridge designs
reduce and consolidate components,
such as bearings and spacers, mak-
ing for easier maintenance, reduced
downtime and less inventory.
Operationally, there are several
fundamental components in a mag-
drive pump design. There are two
separate rotating assemblies (drive
and driven) connected by a mag-
netic coupling. The motor transfers
power through the drive magnet
assembly to the driven magnet as-
sembly, which is connected to the
impeller and ultimately moves the
fluid in the pump system. Between
the two assemblies is a contain-
ment shell that keeps all of the
fluid within the pump and serves
to maintain pressure, acting as a
hermetic seal that prevents fluids
and vapors from escaping to the
atmosphere. The magnets interact
through magnetic flux lines that
are translated across the contain-
ment shell. Within these two assem-
blies are alternating rings of north
and south magnets, which both at-
tract and oppose each other based
on positioning, preventing slippage
from occurring. This type of design
is known as a coaxial synchronous
magnetic drive, and ensures that
both the pump and motor will spin
at the same rate.
Some high-temperature mag-
drive designs (>500F) use a
slightly different design to alleviate
demagnetization effects. The drive
magnet assembly outside the con-
tainment shell is typically the same
as a standard design. However, the
driven assembly consists of a me-
tallic torque ring that couples with
the drive magnet to spin the impel-
ler (Figure 4). This design protects
against excessive temperatures by
removing driven magnets from im-
mersion in high-temperature media,
and is often used in heat-transfer-
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 57
FIGURE 2. One advantage of mag-drive pumps is the absence of
a mechanical seal (shown here), which reduces the risk of leaks
FIGURE 3. Unlike earlier designs, todays mag-drive
pumps are simpler and have fewer components
Source: ITT Goulds Pumps
Source: ITT Goulds Pumps
Feature Report
58 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
media applications, as well as many
other high-temperature chemical,
oil-and-gas and general industry
applications. This design allows for
a small amount of slippage due to
the use of the drive metallic torque
ring, but it typically does not ex-
perience issues with decoupling,
although a slight loss of efficiency
(when compared to traditional mag-
drive designs) may result.
Finally, the rare earth materials
from which magnets are made are
important to understand. The most
common is neodymium iron boron
(NdFeB), which has a high mag-
netic field strength per volume, but
cannot withstand high tempera-
tures. Other materials commonly
used in mag drives are samarium
cobalt (SmCo) and aluminum nickel
cobalt (Alnico). SmCo has slightly
lower magnetic strength than
NdFeB, but can withstand higher
temperatures. Alnico can handle
much higher temperatures than
both NdFeB and SmCo, however it
lacks strength and cannot handle
the torque present in some of the
more demanding pumping applica-
tions. Magnet material selection is
therefore critical when specifying
mag-drive pumps.
Typical applications
Hazardous and regulated services
are the most common applications
for mag drives as they are well-
suited for pumping liquids that
may pose threats to people and the
environment. The mag-drive design
offers heightened safety for work-
ers and better protection for the
environment by eliminating leaks
of hazardous fluids (see boxes on p.
58 and 59). Sealed pumps applied
to these types of services may leak
over time, or require complex double
seals to prevent hazardous liquids
and vapors from escaping to the at-
mosphere, which can lead to safety
hazards, downtime and increased
maintenance requirements.
Some examples of primary mag-
drive applications are liquid pump-
ing of strong acids, strong bases,
and solvents, such as acetone, hy-
drochloric acid, sulfuric acid and
sodium hydroxide. Many of these
would pose a serious health risk to
plant personnel if there is a fluid
or vapor leak. Some materials can
even auto-ignite when exposed to
the atmosphere.
In these situations, a mechani-
cally sealed unit can be riskier and
more expensive than a mag drive.
Typically a traditional mechani-
cally sealed pump in a hazardous
application process would utilize
complex double-seal systems that
are a significant capital investment.
They also require much more main-
tenance and additional monitoring.
Other mag-drive applications can
be where liquid is hard to seal with
a traditional mechanical seal. For
example, pulp-and-paper mills em-
ploy sodium hydroxide applications
where pumpage can crystallize on
seal faces, which then can cause
seal failure. To avoid this, a flush
must be run to the seal that can
increase installation, maintenance,
plant water and energy consump-
tion costs.
The need for environmental
regulation adherence in the mar-
ketplace has also driven aware-
ness of mag-drive pumps. The U.S.
Environmental Protection Agency
(EPA) regulates emissions and
waste, and instituted the Clean Air
Act of 1990, which requires certain
chemicals or services to utilize a
sealless pump. Furthermore, many
chemical plants have implemented
their own set of guidelines based on
internal hazard classifications.
Valuable pumpage, such as mer-
cury and printer ink, along with
other industry services where
downtime brings significant costs,
can also be viable candidates for
mag-drive usage. Single seals leak
fluid upon failure, and once a pump
leaks, the fluid is not usually recov-
erable. This results in lost money
and environmental cleanup time.
A double seal is an expensive and
higher-maintenance solution. Mag-
netically driven pumps can protect
precious pumpage and eliminate
risk of leakage due to their her-
metically sealed design and limited
maintenance needs.
Finally, remote locations are sce-
narios that often call for sealless
mag-drive pumps. As plants ex-
pand, sometimes over miles of land,
some services are located remotely
and are not conducive to routine
monitoring and maintenance. Ex-
amples include wastewater-treat-
ment facilities where pH correction
is needed because water is going to
be introduced back into a system
or a nearby river or lake. This re-
quires technology to eliminate po-
tential leaks and limit maintenance
needs. Another example would be a
sealed pump in a remote area that
would require flushing. This may
require running a significant length
of flush line to the pumps location
REDUCING ENVIRONMENTAL CONCERNS
AT PAPER MILLS
P
ulp-and-paper mills are now able to drastically reduce environmental concerns by
eliminating a primary potential point of failure by replacing sealed pumps with
sealless mag drives. The latest mag-drive designs and technologies feature fewer
parts and are robust enough to withstand the caustic chemicals commonly used in paper
mills, including sodium hydroxide, sulfuric acid, sodium hypochlorite, chlorine dioxide,
and hydrogen peroxide. Any of these chemicals may cause damage to and leakage
through the seal faces, ultimately damaging pumps and posing safety and health risks to
workers. Plant operators can streamline maintenance requirements and utilize mag-drive
pumps to handle hazardous sulfuric acid services commonly found in almost any paper
mill, minimizing potential environmental hazards and saving time and money.
FIGURE 4. This
high-temperature
(>500F) mag-drive
design uses a metallic
torque ring instead of
a drive-magnet as-
sembly to couple with
the drive magnet. Re-
moving magnets from
the high-temperature
pumpage eliminates
the possibility of
driven magnet
demagnetization
Driven torque ring
Motor (drive) Pump (driven)
Drive magnet
assembly
Source: ITT Goulds Pumps
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 59
and also carries high water-usage
costs. Introducing a sealless pump
to a remote location eliminates the
need for seal checks and flushing,
and provides a reliable system with
minimal maintenance.
By taking the seal out of the sys-
tem, a major failure point is elimi-
nated and reliability is enhanced.
Eliminating bearings is a second
feature mag-drive pumps offer that
improves reliability. Close-coupled
mag-drive designs eliminate the
power end, removing the possibil-
ity of oil-lubricated bearing failure,
coupling misalignment, and in most
cases, the need for a baseplate.
Comparison to other seal options
A mag-drive pump is comparable
in cost to single-sealed and canned-
motor pump designs, and is less
costly than double-sealed pumps
that utilize barrier-fluid systems.
There is no replacement of seals
and no running of flush lines, lead-
ing to reduced maintenance and
downtime. When evaluating differ-
ent pump sizes and duty points one
must look at total lifecycle costs.
The chart shown in Figure 5 pro-
vides a breakdown across the vari-
ous pump designs. Canned-motor
pumps require more maintenance
time and dollars, as they are gener-
ally very difficult to work on, and
require a specialized maintenance
shop on site. Also, operators may
need to send the motor out for ser-
vice if there is a breach of the pri-
mary barrier to the internal motor
windings. Double-sealed pumps
have higher costs across pump
sizes compared to mag drives. Mag
drives also deliver optimal
performance, with metallic
mag-drive efficiencies often
equivalent to that of metal-
sealed ANSI pumps. Also
worth noting is that non-
metallic (lined) mag-drive
pumps can be up to 30%
more efficient than metallic seal-
less pumps.
Lined versus metallic
Lined mag-drive designs (Figure 6)
protect the metal casing from cor-
rosion that is common in chemical
applications. Some common linings
are PTFE (polytetrafluoroethyl-
ene), PFA (perfluoroalkoxy alkanes),
ETFA (ethylene tetrafluoroethylene)
and PVDF (polyvinylidene fluoride).
All offer corrosion resistance from
chemicals; however, they are not
universally resistant to all media,
which is why various coating options
exist. Some components can also be
fiber reinforced with carbon or glass.
For example, the impeller can often
be reinforced with these materials to
provide greater protection from hy-
draulic erosion. In a lined mag-drive
pump there is no eddy-current heat
buildup or potential power loss from
currents as the containment shell is
typically fiberglass-reinforced plas-
tic (FRP) that is coated with one of
the linings listed above.
One thing to consider with lined
mag-drive pumps is that they are
generally limited in the areas of
temperature and pressure. The
linings can only accommodate
temperatures in the mid-200F
range, with various casings typi-
cally capable of sustaining design
pressures in the mid to upper 200
psi range. Overall, lined mag-drive
pumps are very good for working
with various acids or bases as long
as they are below certain tempera-
ture and pressure thresholds.
A metallic mag-drive-pump de-
sign (Figure 7) is capable of with-
standing higher pressure and tem-
peratures limits. These pumps are
well suited for solvents, heat-trans-
fer fluids and other non-conductive
fluids that typically run hotter.
Some metallic mag drives can easily
handle over 500F for liquid-service
temperatures. Metallic mag-drive
pumps also are strong solutions
for pumping non-conductive fluids,
such as benzene, that can build up
an electrostatic discharge, which
can be an issue for designs employ-
ing an FRP polymer-lined contain-
ment shell. When using an FRP-
lined shell design, the electrostatic
discharge can arc through the
nonmetal containment shell, caus-
ing a pinhole leak that will cause
complete pump failure over time,
as well as introduce environmental
and personnel hazards that may be
difficult to observe at their onset.
In a metallic mag-drive pump this
arcing charge will not penetrate the
alloy containment shell.
Finally, metallic mag-drive de-
signs have better solids-handling
SAFER WORK ENVIRONMENT FOR
ALUMINUM MANUFACTURER
A
North American architectural aluminum
store-front and door manufacturer used
several anodizing tanks to treat and color
its aluminum products. Each tank contained
17% sulfuric acid that needed to be maintained
at 70F for optimal results. During the course
of the anodizing process, heat was generated
as the sulfuric acid reacted with the aluminum
products, and the acid was pumped out of the
tanks through chillers. Each of the pumps was
a mechanically sealed ANSI pump with a large
sheet of Plexiglas leaning up against the pump
unit, effectively acting as a spray shield. A fine
mist of sulfuric acid would emit from each pump
seal, barely noticed by plant personnel. This
hazardous condition resulted in workers finding
multiple holes in work clothing where the acid
had splashed during the workday. Needless to
say, a change was needed in order to increase
worker safety. Initially, the plant agreed to install
one non-metallic magnetically driven pump as a
test on one of these tanks. The mag-drive pump
cut maintenance, increased safety and reduced
downtime. The replacement was such a success
that mag-drive pumps replaced all mechanically
sealed ANSI pumps, providing a safer and more
efficient work environment for plant personnel.
Pump size
150
100
50
0
L
i
f
e

c
y
c
l
e

c
o
s
t
s
,

%
50-32-160 85-50-200
Single
mechanical
sealed pump
Double
mechanical
sealed pump
Mag drive
Canned
motor pump
Discharge Q = 10 m
3
/h 40 m
3
/h
Head H = 28 m 41 m
Speed n = 2,900 rpm 2,900 rpm
Power P = 1.5 kW 7.0 kW
FIGURE 5. This chart compares the lifecycle costs for centrifugal pumps
using various sealing options
Source: Infractor
DEGUSSA-Hls
Feature Report
60 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
capabilities compared to their lined
counterparts. Metal is more resilient
to solids erosion than a lined pump,
although only up to a point. Also,
with metal-mag-drive designs there
are typically options for providing
additional internal bearing flush
since concerns over breaching and
compromising polymer linings are
eliminated. Metal mag drives also
offer more options for monitoring and
controls. Instrumentation devices,
such as thermocouples, resistance
temperature detectors (RTDs), level
switches and temperature switches
are all more readily available to use
on a metallic mag drive, once again
because concerns about breaching
lined components are eliminated.
Avoiding failure modes
When using mag drives, one can
encounter failure modes not pres-
ent with a sealed-pump applica-
tion. The most common mag-drive
failure mode is dry run. Simply
put, dry run occurs when a pump
is run without fluid. Mag-drive
designs employ process lubricated
bearings often made of carbon or
silicon-carbide material. During dry
run, the lack of fluid in the system
causes the bearings to lose lubrica-
tion, which can result in cracking,
fracture and eventual failure due to
the nature of the bearing material.
Another cause of dry run is when
fluid overheats, boils and flashes off
in the lubrication circuit, effectively
removing process lubrication. This
can lead to chipping, cracking and
increased temperatures that can
melt plastic linings and lead to a
pump seizing.
Some solutions to avoid dry run
are to attach a power monitor to the
pump, which can alert the operator
or control system of the condition,
or just automatically shut the pump
down after a short period of time.
There are also specialized methods
of treating or coating rotating and
stationary silicon-carbide compo-
nent surfaces that reduce their co-
efficient of friction and can, for a
short time, minimize the effects of
dry run.
The other common failure mode
of mag-drive pumps is dead head-
ing, which can occur by running the
pump against a closed discharge
valve. Fluid temperatures begin
to rise quickly because of energy
buildup of impeller rotation in a
closed system, leading to boiling,
cavitation and bearing damage.
Dead heading can be avoided by
flow and temperature monitoring
and controls.
Processing solids can also provide
a set of challenges due to erosion or
clogging. Mag-drive pumps are not
made to handle solids. Introducing
solids will cause accelerated ero-
sion, especially within lined mag-
drive pumps. Solids can also collect
in low-pressure areas in the bear-
ing circuits, typically at the rear
corners of the containment shell,
causing accelerated erosion. Clog-
ging of process lubrication and re-
circulation circuits can also occur
where the bearings can lose lubri-
cation and fail. A primary solution
in metallic mag drives is a bear-
ing flush where added pressure is
introduced to a pump system and
can help to keep solids from build-
ing up in these circuits. Improved
pump designs in both lined and
metallic mag drives can also lead
to more fluid movement (and thus
easier solids removal from problem
areas), achieved by introducing
more channels or adding pumping
actuators in the lubrication circuit.
A final important consideration is
magnetic decoupling. In mag-drive
pumps, the magnetic field between
the magnets spins the impeller.
The magnetic coupling has a torque
limit, so the pump must be prop-
erly sized, and designs must take
into consideration the proper mag-
netic materials as well as sizing. If
magnet materials and size are not
properly specified, the torque limit
is exceeded and the magnetic cou-
pling connection can be broken, re-
sulting in downtime and possible
unit failure. Some common causes of
magnetic decoupling are hard starts
with higher rates of start-up torque
than seen during steady operation,
wet end clogging due to an unex-
pected high shear or fibrous fluid, or
a process upset, such as encounter-
ing colder temperatures than antici-
pated, which causes a spike in fluid
viscosity. Employing a power moni-
tor can detect magnet decoupling
and mitigate these effects.
Final remarks
CPI plant operators continue to gain
a deeper understanding of the latest
magnetically driven pump technolo-
gies, which offer simpler and more ef-
ficient fluid-process solutions. Using
magnetically driven pumps can
yield significant benefits by improv-
ing safety, reducing plant downtime,
slashing maintenance time and as-
sociated costs, cutting onsite parts
inventory and eliminating potential
failure points through a hermetic
sealless design. Todays mag-drive
pumps have ideal processing ap-
plications in industries that handle
hazardous fluids. Mag-drive pump
designs offer distinct advantages
over traditional sealed models when
used in the proper environments
and appropriately specified.
Edited by Gerald Ondrey
Author
Richard Tym is global
product manager for the
non-metallic and mag-drive
product lines at ITT Goulds
Pumps (240 Fall St., Seneca
Falls, NY 13148; Phone: 315-
568-7378; Fax: 315-568-7076;
Email: [email protected]).
During his six years with ITT
Goulds Pumps, Tym has held
various positions in engineer-
ing and product marketing.
He earned a bachelors degree in mechanical en-
gineering from Wilkes University and an MBA
from the Rochester Institute of Technology.
FIGURE 7. Metallic mag-drive pumps
are more suited for higher temperature
and pressure applications
FIGURE 6. Mag-drive pumps can be
supplied with polymer linings for coro-
sion protection
Source: ITT Goulds Pumps Source: ITT Goulds Pumps
Looking for that
dream job in the chemical
process industry?
If interested in posting a job, please contact
DIANE BURLESON | Mobile: 512.250.9555 | [email protected]
Chemploy job center focuses exclusively on jobs in the CPI.
Post your resume and cover letters at ChE.com/Chemploy today!
Receive job alerts that will notify you by email of new jobs posted
that match your search preferences. Create one now and never
miss a new opportunity!
Access our Career Resources library which offers you valuable
coaching and career guides.
Dont let the competition score that perfect position you deserve.
Let Chemploy work for you.
ChE.com/Chemploy
S
econd only to electric motors,
centrifugal pumps are the
most common machine used
in the chemical process indus-
tries (CPI). Pumps are serving in
every conceivable fluid application.
They move all manner of fluids from
wastewater to paper pulp, from ul-
tra-clean and purest pharmaceuti-
cal liquids to crude oils laden with a
great variety of contaminants. Hun-
dreds of millions of these pumps
are fitted with mechanical seals
at the point where shafts protrude
through the pump casing. And some
of these seals must satisfy very spe-
cial requirements; the prevention of
contamination is among them.
Appropriately, process pumps in
the pharmaceutical and food-and-
beverage industries are subjected
to stringent hygiene and cleaning
requirements. These include clean-
in-place (CIP), and steam-in-place
(SIP). Industry and its regula-
tory agencies seek to reduce, and
hopefully eliminate, the possibil-
ity of bacteria and micro-organism
growth. Cleanliness is especially
important on surfaces that are in
contact with, or wetted by, the pro-
cessed media. Needless to say, such
contamination is detrimental to the
finished processed product; there-
fore, considerable efforts are made
by plant operators, engineers and
managers to avoid contamination.
But how thorough are the prevail-
ing cleaning routines, and how suc-
cessful are even the most diligent
efforts around the restricted and
confined spaces of the all-important
mechanical seal? Clearly, the an-
swer to this question depends on
the design of the mechanical seal
and the seal housing. More specifi-
cally, cleaning effectiveness is in-
fluenced by the geometry of sealing
components contacted by the pro-
cess fluid.
Seal design considerations
The three main causes of pump
process-fluid contamination in hy-
gienic applications are easily recog-
nized, as follows:
1. Microorganisms can enter the pro-
cess fluid from the atmospheric
side of the mechanical seal and
may pass through the seal fluid
film.
2. Process fluid could pass through
the sealing fluid film to the non-
process fluid side, which may
lead to microorganism growth in
the residues. These microorgan-
isms could then move back across
the seal fluid film into the pro-
cess fluid where they could cause
contamination.
3. Process fluid could stick to the
process-wetted components of the
seal or seal cavity. In that case,
it would be difficult to properly
clean the seal region after pro-
cessing each batch. This could
lead to microorganism growth
and contamination.
The issue is of concern to the Eu-
ropean Hygienic Engineering and
Design Group (EHEDG), an inter-
national body which helps industry
focus on best-practices guidelines
for mechanical seal designs. Among
the considerations spelled out by
EHEDG for hygienic and aseptic
applications, we find a classification
of hygienic equipment into the fol-
lowing three groups:
1. Aseptic
2. Hygienic Equipment Class I
3. Hygienic Equipment Class II
Across all groups or categories, the
EHEDG stipulates that the sealing
Feature Report
62 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Feature Report
Heinz P. Bloch
Consultant
For applications that
require cleanliness,
be sure your
centrifugal pumps
have the proper seals
Mechanical Seals Update:
Pharmaceutical and Food Applications
Product-wetted
components
are surrounded
by orange color
Part 2
FIGURE 1. This cutaway shows a traditional component-style mechanical seal. A
buffer fuid is introduced into the space between inside and external seals
device should protect the process
fluid from being contaminated by
the fluid environment. It should be
easy to clean the sealing region to
reduce the risk of microorganism
growth. It is intuitively evident that
equipment that is difficult to clean
will result in an inferior processed
product. Flawed product quality
may result in a rejected product
batch, incur additional reprocess-
ing cost, force product recalls and
represent a real danger for human
consumption or use.
Within the three equipment
groups or categories, Class I and
Aseptic equipment requirements
detail the use of an external seal to
create a buffer region (seal cavity).
This buffer region can be continu-
ally flushed with an appropriate
fluid. A dual-seal arrangement is
intended to reduce the possibility
of cross-contamination and issues
arising from process fluid traveling
across the seal fluid film of the in-
board seal faces.
EHEDG also stipulates that all
unavoidable gaps must be sited at
the non-process fluid side of the
seal and the components in con-
tact with the process fluid must be
smooth and free of crevices. Again,
this guideline is intended to re-
duce the potential for bacteria and
microorganism growth. It would
serve no-ones best interests to have
process fluids stick to any part of
a pump. Contamination risks are
even greater when changing batch
composition, or with time elapsing
between successive batches.
Reality versus best practice
Informal surveys show that many
seals presently found in the food,
beverage and pharmaceutical
industries are not representing
best-available designs. Single-coil
spring component seal designs
of the 1970s and 1980s (Figure 1)
are still dominant and in common
use. Note that Figure 1 depicts an
old-style dual (inboard versus ex-
ternal face to face) component
mechanical seal used in certain
hygienic applications.
However, on the process side, the
fluid (shown in orange in Figure 1)
is in direct contact with multiple
seal crevices and cavities. It will
be impractical, if not impossible,
to thoroughly clean these regions.
As an aside, practically every best-
practice seal-design guideline has
been ignored in this particular ge-
ometry. Regrettably, this is not an
isolated issue.
Figure 2 illustrates another
family of similarly unsuitable or
outdated designs. All three are in-
ternal/external component-seal de-
signs with buffer fluid. These seals
find extensive use in the food-and-
beverage industry. But these and
similar designs have significant
bacteria and microorganism growth
potential around the components
wetted by the process fluid. While
the issue is entirely design-related,
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 63

FIGURE 2. Shown here is range of traditional, risky, external and internal component seal designs. These are still found in hy-
gienic applications. Internal components are wetted by process fuid, shown in orange. Arrows point to locations where buffer
fuid is injected
Product wetted
components
FIGURE 3. Shown here is a cartridge seal design for use in hygienic applications.
Buffer fuid is introduced into the space between the product-wetted seal on the left,
and the external seal on the right side
Feature Report
64 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
it can, and has been, successfully
avoided by the intelligent redesign
depicted in Figure 3.
Using the seal in Figure 3 for new
and existing pumps in hygienic
services allows plant engineers to
avoid substantial risk. This me-
chanical seal is not only easier to
clean, but fully harmonizes with
international best practice guide-
lines. The design is uncomplicated
and very cost-effective. Most im-
portant: It fits in the space shown
earlier in Figure 1 and represents
true state-of-the-art technology.
Note also that the component
seals in Figures 1 and 2 will require
careful dismantling and reassem-
bly. In contrast, the recommended
state-of-the-art slip-in design of
Figure 3 can be fully assembled
at the factory, which reduces field
work and potential errors. More-
over, the possibility of process-fluid
contamination is greatly lessened
by incorporating only smoothly con-
toured wetted parts. Common sense
convinces us that components with
smooth surface finishes facilitate
cleaning and sterilization. Elimi-
nating crevices and cavities makes
it much more difficult for micro-
organisms and bacteria to adhere
to surfaces. In the state-of-the-art
seal of Figure 3, springs and drive
mechanisms cannot be contacted
by the process fluid.
So, while single-spring compo-
nent seals may appear to be low-
cost sealing solutions, they do have
many shortcomings. Best-practices
companies recognize the hidden
costs and contamination risks asso-
ciated with outdated designs. Risk-
averse users increasingly make
innovative seal manufacturers
one of their technology resources.
As business partners, both manu-
facturers and users demand what
best practices guidelines require.
Not all mechanical seal designs are
the same. Reliability-focused engi-
neers look at both the big picture
and the details of the best avail-
able seal designs.
Edited by Gerald Ondrey
Acknowledgement
All three figures courtesy of AESSEAL plc,
(Rotherham, U.K. and Rockford, Tenn.)
Author
Heinz P. Bloch (heinz
[email protected]) resides in
Westminster, Colo. His pro-
fessional career commenced
in 1962 and included long-
term assignments as Exxon
Chemicals Regional Machin-
ery Specialist for the U.S.
He has authored over 600
publications, among them 18
comprehensive books on prac-
tical machinery management,
failure analysis, failure avoidance, compressors,
steam turbines, pumps, oil mist lubrication and
practical lubrication for industry. Bloch holds
B.S. and M.S. degrees in mechanical engineer-
ing. He is an ASME Life Fellow and maintains
registration as a Professional Engineer in New
Jersey and Texas.
Circle 31 on p. 76 or go to adlinks.che.com/50980-31
EASY INSTALLATION
ho holes in tanks or pipes
Awa] from sensitive processes
VERSATILE
0ne size adjusts to motors, from
small up to 15Ohp
works on 8 phase, fxed or variaole
frequenc], DC and single phase power
SENSITIVE
1O times more sensitive than
just sensing amps
CONVENIENT OUTPUTS
For meters, controllers, computers
4-2O milliamps O-1O volts
MONITOR VISCOSITY SIMPLY
CALL NOW FOR YOUR FREE 30-DAY TRIAL 888-600-3247
SENSE MIXER MOTOR HORSEPOWER
WITH UNIVERSAL POWER CELL
24
0
22
20
18
14
12
10
8
6
4
2
16

POWER DECREASE
SHOWS BATCH
IS DONE
BEGIN HIGH
SPEED MIX
ADD LIQUID
LOW SPEED
DRY MIX
HIGH SPEED
BATCH 1 BATCH 2 BATCH 3
POWER
SENSOR
MIXER
MOTOR
Power changes refect viscosit] changes
0ood oatches will ft the normal "profle" for
that product
PROFILING A PROCESS
WWW.LOADCONTROLS.COM
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 65
Environmental Manager
W
illiam Banholzer gave
an opening keynote ad-
dress at the AIChE Spring
Meeting (New Orleans,
La.; March 31) that was interest-
ing, fun and brave. It reminded
me of the Six Sigma for Research
and Development [R&D] training
that UOP provided to me many
years ago. The following principles
regarding R&D were taught in that
training: the goal is profit, not data;
new apparatuses do not necessarily
lead to new products; there must be
a market for any new product and
that product must be manufactur-
able at a reasonable cost; and the
new product must be protectable
(such as via patents).
Banholzers presentation, en-
titled The World Needs Engineer-
ing Judgment, contained some
similar themes directed at com-
modity chemicals. R&D should be
regarded as a privilege and not a
right. In todays companies, new
products provide only about 8%
of their profits. Invention is not
enough. The new product must be
desirable and affordable.
Banholzer gave some micro and
macro examples of new technolo-
gies. He was skeptical regarding
all of the following: the conversion
of greenhouse gases into biodegrad-
able plastics; the conversion of algae
to crude oil; the use of graphene
nanotubes for desalination; the use
of sugar to create ethanol and then
ethylene and then polyethylene for
softdrink bio-bottles. Overall, bio
has under-delivered, he stated. He
also said that distillation works
and that there are hurdles to re-
placing it. On the other hand, heat
integrations of distillation units
have been successful. He recom-
mended asking questions like the
following regarding new processes:
How much energy is in the starting
material? How much energy is re-
quired for conversions? How much
energy is in the final products?
Banholzer also gave examples
of research work that has truly
yielded appreciable dividends. The
production costs of low-den-
sity polyethylene are now
at about 10% of those in the
1950s. Shale gas is producing
seven times more energy than
what is required to isolate it.
Mechanical hurdles have been
overcome to allow the construction
of larger, more-efficient plants.
Surveys have shown that consum-
ers and buyers are extremely hesi-
tant to pay for green. This places
an extra burden on the people who
do research work on new products
and processes. At the same time,
new chemical processes usually re-
quire about 20 years to show profits.
Large companies and small compa-
nies need to be very careful not to
initiate research projects that might
be doomed, especially if they fail to
analyze the realistic costs and bene-
fits of the new processes. Banholzer
seemed to purposely avoid the Fed-
eral Governments role in funding
energy and chemical projects that
might waste taxpayer money.
Banholzer started and finished
his presentation with some very
good news for the more than
2,000 attendees at his presenta-
tion: the skills of chemical engi-
neers are needed now more than
ever. Hopefully, not too many of
them will be working on almost-
hopeless research projects.
Mike Resetarits
Fractionation Column
The practical side of R&D
With 38 years of experience, Mike Resetarits
consults on distillation, absorption and extrac-
tion processes. Each month, Mike shares his
frst-hand experiences with CE readers
Rugged
dependability with
advanced sealing
technology
Superior resistance
to leakage
Seals available
from many seal
manufacturers
Retrot kits
available for
existing pumps
Call us or visit www.rpcinnovations.com to learn more.
706.335.5551
Circle 42 on p. 76 or go to adlinks.che.com/50980-42
P
H
O
T
O
:
A
3
6
9
/
T
H
I
N
K
S
T
O
C
K
Brkert Fluid Control Systems
BWA Water Additives
Chemineer
Collins Instrument
Dow Water & Process Solutions
Eastman Therminol
Fike Corp.
Fluid Metering
GEA Heat Exchanger
Gem Valves
Inline Industries
OTEK Corp.
Outotec
Ross
Water Management
special advertising section
CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014||||||67
Water Management Special Advertising Section
Water in mining: from liability to valuable resource
In the mining industry, the perception of water has changed: from a waste product to
be treated, to a valuable resource needing proper management, says Outotec
W
ater management in the mining and minerals industries
needs to include optimizing usage across the mine or con-
centrator site, minimizing fresh water use, minimizing waste from
water treatment, and practices for water reuse and recycling.
To succeed, companies offering water management solutions
for the mining industry must have a deep understanding of min-
ing and mineral processes. Just being good at water treatment
technologies is not enough. Outotecs Industrial Water Treatment
offering combines mineral processing know-how built up over
several decades with water treatment expertise to develop tailor-
made and optimized solutions for customers.
Water in the mining industry is complex and site-specific, since
the composition of impurities depends on the ore itself and how it
is processed. Typical impurities in wastewater are metals, arsenic,
sulfate, chloride and cyanide, often at toxic concentrations.
Water treatment processes must meet two targets. First, the
treated water should be of high enough quality so that it can be
recycled to the mineral processing plant, thus reducing fresh
water consumption. Secondly, the process must be efficient and
reliable so that the mining company can meet the requirements of
its environmental permits.
Outotec has developed several processes that meet these tar-
gets. They combine proprietary and patented process technology
with Outotecs equipment offerings in reactors and dewatering,
plus high-quality engineering and automation systems.
An example is Outotecs Ettringite process for managing sul-
fate, which is a common and growing challenge in the industry.
This two- or three-step process precipitates sulfate and calcium,
lowering the scaling potential and total dissolved solids (TDS)
content of the treated water while also removing many other im-
purities such as metals. www.outotec.com
A deep understanding of the mining sector gives Outotec a
head start in designing specialist water treatment processes
A single solution for drinking water analysis
Brkert Fluid Control Systems presents a modular end-
to-end system that can be expanded at any time
T
he continuous analysis of water param-
eters can be costly, usually requiring
several different systems with separate
displays, controls and sensors. The Type
8905 Online Analysis System from Brkert,
on the other hand, combines all the mea-
surements relevant to drinking water anal-
ysis in a single compact and modular unit.
The basic version of the Online Analysis
System includes standalone analysis
cubes for five measurement parameters:
pH, redox (ORP), conductivity, free chlo-
rine and turbidity. All measurements have
upper and lower alarm thresholds. The
measured values are stored internally, and
also optionally sent to a remote system.
Additional sensor types and system
functions are available to expand the per-
formance of the modular system step by
step. Retrofits are possible at any time.
The next steps up are on one side to add
sensor cubes for more sophisticated pa-
rameters and on the other side to extend
the range of control modules and enhance
the software to more control capabilities.
The analysis modules combine leading
micro-technologies with chemical, physical
and optical measuring principles. Modules
are hot-swappable and can be combined
as needed for customized applications.
The compact design of the platform
provides a range of savings opportunities
for users. For example, the new device re-
quires less space than previous standard
systems, has lower energy consumption,
and requires less wiring. It also needs less
maintenance, since the platform combines
the functions of numerous separate sen-
sors and all the units can be purchased
from a single source. It can easily be inte-
grated into existing systems, or quickly in-
stalled in the field.
The functional scope of the Online
Analysis System is initially optimized for
municipal waterworks. By supporting
drinking water treatment specialists in
their daily work, the unit can contribute to
cost-effective and safe drinking water pro-
duction through optimization of individual
process steps. www.burkert.com
The Type 8905 Online Analysis System
replaces a range of individual analyzers
68||||||CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014
Water Management Special Advertising Section
I
n plant engineering there is a great de-
mand for application-specific compo-
nents with a wide range of functions that
save space and weight, and are easy to
install. Compact, lightweight plastic dia-
phragm valves fall into this category,
offering cost-effective alternatives to con-
ventional valve designs.
The new R690 pneumatic and R677
manual plastic diaphragm valves from
GEM, the premier engineering special-
ists for valves, measurement and control
systems, check all the boxes for most ap-
plications: They are small and compact,
lightweight, and designed so that com-
binations of several nominal sizes can be
installed on the same mounting height
plane. For installation, the valves are sup-
plied in all standard connections for the
different international standards.
Despite their compact size and smaller
dimensions, the new flow-optimized valve
bodies provide the same high flowrates
as the previous models. In some cases,
flowrates are even higher. Depending on
the valve design, they are reliable at tem-
peratures from 20C to +80C, and at
pressures up to 10 bar (150 PSI).
The product line comprises nominal
sizes from 4 in. In the course of re-
designing its products, GEM has also
succeeded in reducing the control air con-
sumption of the type R690 pneumatic ac-
tuated version.
In addition to the standard optical posi-
tion indicators, options such as electrical
position indicators, positioners or process
controllers, pilot valves, seal adjusters and
stroke limiters are available. Valve bodies
are available in a variety of plastics (PVC-
U, PP, ABS, PVDF, etc.) and with a range of
seal materials (EPDM, PTFE, FPM, NBR).
These compact plastic diaphragm
valves are suitable for use in chemical
process plants, for plant solutions in sur-
face finishing, coating and electroplating,
municipal and industrial water treat-
ment, fluid handling in technologies such
as reverse osmosis, neutralization, and
microfiltration, and for chemical processes
with aggressive and corrosive media, such
as electronics manufacturing, fertilizers,
and detergents. www.gemu.com
Lightweight yet capable: GEMs
R690 pneumatic diaphragm valve series
Compact, smaller, and better value
GEM valves represent a milestone in industrial plastic piping systems, saving space
and weight yet out-performing metal valves in corrosive environments
S
ince 1945, Fike Corp.
has provided world-
class overpressure protec-
tion solutions, and is the
industry leader in delivering
reliable yet innovative products
that exceed customer expectations.
From safeguarding critical manufacturing
processes to protecting pressure relief valves
(PRVs), Fike products are part of the critical path to lower-
ing costs and helping companies achieve higher profitability.
A rupture disc is designed to provide a leak-tight seal within
a pipe or vessel until the internal pressure rises to a predeter-
mined level. At that point the disc bursts, preventing damage to
the equipment from overpressure. Liquid-full systems create a
number of processing challenges, the solution to many of which
lies in rupture disc technology. The typical rupture disc begins to
respond to pressure in excess of the burst pressure in less than
1 millisecond. This means that a short-duration pressure spike that
is not detectable by normal process instrumentation will activate
the rupture disc, saving the process vessel from overpressure.
In addition to a full line of standard products, Fike also manu-
factures custom engineered rupture discs tailored to the appli-
cation. Fike engineers and application specialists consider many
important factors such as type of application, operating condi-
tions, inlet/outlet configurations, rupture disc specifications, and
special process requirements.
To support this work, Fike has an on-site flow laboratory and
a metallurgy lab. The Fike Flow Laboratory is a general-purpose
flow characterization laboratory for quantifying the performance
of rupture discs, rupture disc/relief valve combinations, and any
other device whose flow capacity or resistance to flow must be de-
termined. Test equipment for diameters of 4 in. (DN6 to DN100)
allows a wide range of disc sizes and installations to be tested.
Specific applications are simulated to check that custom solutions
provided by Fike engineers will perform as specified.
The Fike Metallurgy Lab is used to gain understanding of the
behavior of materials necessary for different applications. Fike
is a single-source supplier giving full service for fire, explosion
protection and pressure relief. From product development to cus-
tomer support, Fike provides quality solutions. www.fike.com
Fike manufactures a wide range of rupture discs, both standard
and custom, to protect equipment against excessive pressure
From hygienic processes
to wastewater treatment,
Fike offers peace of mind
World-class overpressure protection solutions
CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014||||||69
Water Management Special Advertising Section
This compact mixer boasts big performance
The Kenics UltraTab Static Mixer from Chemineer is designed for turbulent flow
applications in pipe diameters ranging up to 60 in. and above
C
hemineer is offering the Kenics
UltraTab static mixer designed for
turbulent flow applications where a high
degree of mixing is required in a compact
space.
The Kenics UltraTab provides a com-
bination of advantages, including its
compact installation space requirement,
its complete blending in short distances
downstream of the mixer, and the low pres-
sure drop through the mixing element.
Some of the key features and benefits
of the Kenics UltraTab static mixer include:
integral wall injector upstream of the
mixing element that forces flow stream
additives through the high energy dis-
sipation region created by the mixing
element which provides superior mixing
efficiency;
low pressure drop through the UltraTab
element enhances process energy effi-
ciency and saves pump energy;
compact design and short mixing length
minimizes pipe lengths and optimizes
the efficiency of the plant layout.
Product specifications of the Kenics
UltraTab static mixer include:
size range 260+ in.;
NPT or flanged injectors;
materials available include carbon steel,
stainless steel, coated carbon steel or
316 stainless steel, FRP, and high alloys;
housing options include between-flange
tab and spool piece designs.
Chemineer is a brand of National Oilwell
Varco. Chemineers mixing expertise in-
cludes high-flow, low-shear liquid-liquid/
solids blending, gas dispersion, high-shear
blending and viscous mixing. Chemineer
has operations in Dayton, Ohio; North
Andover, Mass.; Derby, England; Mexico,
D.F.; Singapore, and China.
With its headquarters in Houston, Tex.,
National Oilwell Varco has over 170 years
experience providing products and ser-
vices to the international oil and gas indus-
try. It has more than 100 subsidiaries and
over 60,000 employees at over 1,000 sites
around the world, plus annual revenues in
excess of $20 billion. www.chemineer.com
An integral injector simplifies the
dosing of additives into the fluid stream
Technologies for wastewater treatment and reuse
Innovative Dow wastewater treatment technologies offer reduced energy use, less
fouling and better performance
A
s water becomes increasingly precious,
industries and municipalities world-
wide are turning to innovative water treat-
ment and reuse technologies to help meet
demand. Dow Water & Process Solutions
(DW&PS) offers a broad range of compo-
nent technologies to help water-intensive
industries and municipalities make the
most of every drop of water available.
Focused on advanced separation
technologies for wastewater treatment,
DW&PS is committed to maximizing the
vast potential in the worlds reusable
water, and working with industries and
communities to recover water, energy, nu-
trients and other valuable components of
wastewater streams.
Known for its industry-leading DOW
FILMTEC elements, DW&PS has devel-
oped an innovative XFR fouling-resistant
technology and optimized spacer design
for challenging water treatment. Applying
this technology to its highest-rejection
and lowest-energy membranes, DW&PS
offers a range of 8-in. products tailored
specifically for industrial and municipal
wastewater treatment. Lower energy con-
sumption, higher fluxes, fewer cleanings,
and greater rejection of contaminants sig-
nificantly improve sustainability and better
enable water reuse even in challenging
applications.
Applying the same science and quality
that have made DOW FILMTEC elements
so successful worldwide, DOW IntegraFlo
ultrafiltration modules have established a
new global standard. IntegraFlo modules
feature an outside-in configuration for
higher solids loading. The PVDF membrane
material and very narrow pore size dis-
tribution make the modules an excellent
choice for wastewater treatment and offer
high removal of suspended solids, bacte-
ria, viruses and organics.
In addition, the innovative TEQUATIC
PLUS fine particle filter combines the
power of continuously cleaning, cross-flow
filtration with centrifugal separation and
solids collection into one device.
For municipalities and industries such
as chemical, petrochemical, pulp and
paper, textile, steel, and food and bever-
age, DW&PS technology is helping to turn
wastewater streams into a valuable re-
source by allowing the specific removal of
pollutants and re-use of treated wastewa-
ter in industrial processes, boilers, cooling
and utilities. dowwaterandprocess.com
Dow membranes and filter systems
aid the re-use of precious water
70||||||CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014
Water Management Special Advertising Section
Keeping supplies of fresh water flowing
Eastman Therminol heat transfer fluids play a key role in the efficient and reliable
operation of thermal desalination plants
A
ccording to www.unwater.org, by 2025,
two-thirds of the worlds population
could be under freshwater stress condi-
tions. Current estimates indicate only 0.5%
of the global water supply is available as
fresh water. An additional 2.5% is frozen
water at the poles or in glaciers, and the
remaining 97% is undrinkable seawater.
To sustain a growing global population
with safe and dependable supplies of fresh
water, recycling of wastewater or desalina-
tion of seawater is critical. Several desali-
nation technologies exist; those based on
distillation may use heat transfer fluids.
Eastman Therminol heat transfer flu-
ids are available to support desalination
process needs, whether the energy source
is from concentrating solar or fuel-fired
heaters. Thermal stability ensures long
life for the fluid, resistance to fouling, and
excellent fluid-side heat transfer coeffi-
cients for consistent and reliable service.
Additionally, CSP (concentrating solar
power) hybrid applications, combining CSP
and desalination, are a new development
in alternative energy and water recycling
technologies. Again, Therminol heat trans-
fer fluids can help.
Therminol 66 is the worlds most popu-
lar high-temperature, liquid-phase heat
transfer fluid. Therminol 66 is pumpable
at low temperatures, and offers high-
temperature thermal stability.
Therminol 59 is a synthetic fluid with ex-
cellent low-temperature pumping char-
acteristics and thermal stability.
Therminol XP heat transfer fluid is an ex-
tremely pure white mineral oil which pro-
vides reliable heat transfer.
Therminol 55 is a synthetic fluid used
in moderate-temperature applications.
Therminol 55 fluid is designed for use in
non-pressurized /low-pressure, indirect
heating systems. It delivers efficient, de-
pendable, uniform process heat with no
need for high pressures.
Therminol VP-1 heat transfer fluid is an
ultra-high-temperature synthetic fluid
designed to meet demanding require-
ments in vapor-phase or liquid-phase
systems. It is an excellent option for
CSP/desalination hybrid systems.
Eastmans TLC Total Lifecycle Care
Program is designed to support Therminol
customers throughout their systems life-
cycle. This comprehensive program in-
cludes system design support, start up
assistance, training, sample analysis, flush
and refill fluids and more.
www.therminol.com
Desalination: a key technology for
expanding future fresh water supplies
Static mixers with low pressure drop
Ross LPD Low Pressure Drop Static Mixers are ideal for effective fluid mixing in water
and wastewater treatment processes
T
he Ross Low Pressure Drop (LPD) Static
Mixer enables more efficient dosing
of flocculants, disinfectants, neutralizing
agents and pH conditioners into a water
stream. This simple-to-install heavy-duty
device completely mixes treatment chemi-
cals within a short length of pipe. When
used in conjunction with automated instru-
mentation, the LPD delivers predictable
quality control based on a virtually mainte-
nance-free operation.
The LPD Static Mixer consists of a se-
ries of baffles or elements discriminately
positioned in series. Each element com-
prises a pair of semi-elliptical plates set 90
degrees to each other. The next element is
rotated 90 degrees about the central axis
with respect to the previous baffle set, and
so on. For even lower pressure drop, an
LLPD model is also available, in which the
plates of each element are oriented at 120
degrees relative to each other.
As the fluid moves through each LPD
or LLPD element, flow is continuously split
into layers and rotated in alternating clock-
wise and counterclockwise directions.
This method of subdividing the stream
and generating striations leads to highly
efficient and repeatable mixing with mini-
mal pressure loss. During turbulent flow,
the baffles enhance the random motion
of molecules and the formation of eddies.
In most water and wastewater processes,
four or six elements are more than suf-
ficient to completely disperse treatment
chemicals and create a very uniform solu-
tion or suspension.
Small LPD/LLPD mixers of 1 in. through
2.5 in. in diameter are welded to a central
rod, while larger elements are welded to
four outside support rods for maximum
rigidity and stability. Available in a wide
range of sizes up to 48 in. in diameter,
these mixers can be supplied as pipe in-
serts or as complete modules with housing
and injection ports.
In addition to Static Mixers, Ross also
manufactures High Shear Mixers and
Multi-Shaft Mixers used in the production
of water treatment chemicals. The compa-
ny offers no-charge mixer testing services
and an extensive trial/rental program.
www.mixers.com
Four or six mixing elements are
usually more than sufficient for effective
mixing under turbulent flow conditions,
Ross says. Diameters range from 1 in.
through 48 in.
CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014||||||71
Water Management Special Advertising Section
Building valve solutions for water treatment
Inline Industries has a proud tradition as a vertical manufacturer, designing and
building a wide range of high-quality valves
I
nline Industries is
a pioneer in build-
ing valve solutions for
OEM equipment and
water treatment plant
operations.
Inline Industries has
been providing inno-
vative valve solutions
to the treatment industry
for over 21 years. From manually
operated valves and automated
valve assemblies to high-perfor-
mance control valves, Inline has
built a strong reputation for man-
ufacturing high quality, consis-
tent and reliable products.
Inline has been able to
achieve this by designing and
building its own valve products
as a vertically integrated manu-
facturer. The company pours its own castings, machines, then
assembles and tests each valve to exacting industry standards.
Valves are cast to applicable ASTM material standards and de-
signed and tested to ASME B16.34 specifications to assure buyers
that the products will perform at the pressures and temperatures
for which they are designed. Each casting is heat stamped and
documented through an ISO 9001:2008 quality control process to
provide consistency and complete product traceability.
Inline offers a wide range of valve styles including valves with
compression ends for chemical injection tubing systems; two-way,
full and standard port valves with threaded, grooved or flanged
ends in economical low-pressure and high-pressure versions; and
three-way diverter and multi-port valves for bypass, tank farm
and filtration applications.
Inline also offers a spring return normally closed handle al-
lowing the lab to take samples at various points in the treatment
process, as well as valves capable of pressures to 4,000 PSI for
the most demanding applications. Inline can provide actuated
packages complete with accessories such as direct mount electric
or pneumatic actuators; limit switches; solenoids; and digital or
pneumatic positioners all factory mounted and tested.
At the heart of Inlines success over the years has been its abil-
ity to deliver. Inlines headquarters, located in Rosemead, Calif.,
houses an extensive multimillion dollar inventory, machine shop,
and automation center, enabling the company to ship 95% of all
orders complete in 48 hours.
Inline is supported by a select network of distributors that are
highly trained in helping provide customers with valve solutions.
www.ballvalve.com
Inline Industries 334 valve
with pneumatic actuator
Methanol metering for wastewater denitrification
An innovative metering pump from Fluid Metering boasts excellent performance when
dosing methanol into processes for removing nitrate from wastewater
N
itrate, an end-product of the bacte-
rial degradation of ammonia, is pres-
ent in high levels in untreated wastewater.
The release of effluent containing high
concentrations of nitrate into bays and
watersheds can have a devastating effect
on water ecosystems. Through a process
known as denitrification, water treatment
facilities therefore convert excess nitrate
into harmless nitrogen gas.
The anaerobic bacterial process that
breaks down nitrate is accelerated by
adding methanol to the wastewater. The
CeramPump QDX Hazardous Duty Metering
Pump from Fluid Metering has proven to
be an excellent choice for methanol meter-
ing in wastewater denitrification, thanks
to its unique valveless design. This is es-
pecially true in small to mid-size treatment
facilities, where methanol flowrates are
extremely low; this often causes valved
pump designs to become air-bound and
lose prime, the company says.
The CeramPump has only one moving
part in contact with the process fluid: a
rotating and reciprocating ceramic piston.
As with a conventional piston pump, the
pistons reciprocating motion performs
the pumping function. However, this is
where the similarity to conventional piston
pumps ends.
During the pumping cycle the
CeramPump piston simultaneously ro-
tates, alternately opening and closing the
inlet and outlet ports of the pump, and
hence effectively functioning as a valve. At
no point are the inlet and out ports inter-
connected, thus eliminating the need for
check valves. The pump drive is FMIs QDX
Hazardous Duty Drive, typically required
for pumping methanol.
Fluid Metering, Inc. patented the first
rotating and reciprocating valveless pump
and has been providing fluid control so-
lutions for medical, analytical, chemical,
and industrial applications for over 50
years. In each of these markets FMI pumps
can be found from the laboratory to the
production floor, incorporated into OEM
equipment and instrumentation, as well as
process control and field installations.
Flowrates range from 2.5 l/dispense to
4.6 l/min, with pressures to 200 psig. FMI
pumps will dispense and meter fluids for
millions of cycles with a drift-free accuracy
of better than 1%. fluidmetering.com
Small but tough: the CeramPump
72||||||CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014
Water Management Special Advertising Section
Polypropylene makes the difference
GEA BIOdek trickling filter media made from polypropylene are stronger and more
environment-friendly than their PVC equivalents
T
rickling filter media made of polypropylene (PP) have gained
growing acceptance in recent decades, notes GEA Heat
Exchangers, because they have valuable features that make them
attractive substitutes for commonly used PVC fills.
Simple though plastic trickling filter media might appear, they
have to meet many criteria if the biological treatment process is to
be successful. They should provide a large surface for the biofilm
to grow. Sufficient air circulation is necessary to provide the re-
quired oxygen. The biofilm should have the appropriate thickness,
and the water should flow through slowly and evenly. The result is
a balanced three-phase system in which water, air, and biosolids
share the void space within the fill medium.
Achieving this balance is a challenge for the design engineer.
BIOdek fills from GEA Heat Exchangers are available in a selection
of media types to accommodate the process requirements with
any desired type of flow pattern and a variety of channel sizes.
As well as meeting the process requirements, the medium
must be self-supporting and rigid enough to withstand the weight
of the biofilm and captured water. It must retain its shape for de-
cades, and must be environment-friendly in manufacture and dis-
posal. Here PP has several advantages over PVC:
PP is less brittle than PVC, so during inspections an operator
can walk on top of a PP bed without damaging it. PVC filters re-
quire a separate PVC grating to prevent breakage.
PP is less dense than PVC, so PP sheets are much thicker than
PVC sheets of the same weight. This provides greater resistance
to erosion and media buckling, which is the most common cause
of failure when a filter collapses.
GEA BIOdek PP media are thermo-welded, eliminating the sol-
vent emissions associated with manufacturing PVC products.
PP media can be recycled at the end of their working lives.
www.gea-heatexchangers.com
Tough stuff: Trickling filter media made from polypropylene
need no protective grating to prevent damage during inspection
Plastic control valves handle corrosive chemicals
Collins 2-in. valves and actuators are specially designed to handle corrosive fluids
acids, bleaches, chlorine, pH control and aggressive environments
C
ollins Instrument Companys line of
economical 2-in. flanged plastic control
valves handle corrosive liquids including
hydrochloric acid, caustic, sulfuric acid,
and many others. With bodies of either
PVDF or polypropylene, these highly-re-
sponsive control valves are specifically de-
signed for use with corrosive media and/or
corrosive atmospheres.
Suitable for applications in numerous
industries, including chemical, petrochem-
ical, pulp and paper, and municipal, these
valves are extremely corrosion-resistant,
and feature fast-acting positioning (stroke
rate approximately
1
2 in./s). They are avail-
able with a wide selection of trim sizes, in
globe, angle, and corner configurations.
The differential-area piston eliminates
the necessity for auxiliary loading regula-
tors. All actuator parts apart from the inte-
gral positioner are molded of glass-filled,
UV-inhibited polypropylene. Before ship-
ment, the aluminum positioner and a por-
tion of the cylinder are immersed in Dip
Seal to provide atmospheric protection.
The integral positioner eliminates the need
for external linkages which are subject to
corrosion and malfunctioning. Valves may
also be furnished without a positioner for
on/off applications.
Collins also offers a plastic pneumatic
actuator. The combination of a plastic ac-
tuator and a plastic valve body provides
an effective way to handle both corrosive
materials flowing through the valve, and
harsh environments that can attack the
outside of the valve and actuator. Collins
plastic control valve packages withstand
salty marine atmospheres as well as indus-
trial environments that are too corrosive
for metal valves and actuators.
Collins actuators incorporate a unique
internal locking ring to attach the cylin-
der to the yoke. A semicircular groove is
machined inside the lower edge of the cyl-
inder, and a matching groove cut in the
yoke. When the yoke and cylinder are as-
sembled, a flexible polypropylene rod is
inserted into the groove through a slot in
the side of the cylinder, securing the two
sections together.
Along with its corrosion resistance the
Collins control valve features a stem pack-
ing arrangement that virtually eliminates
the problem of fugitive emissions, thereby
protecting the environment.
Located on the Texas Gulf Coast in
the town of Angleton, Collins Instrument
Company has been serving the chemical
and petrochemical industry for over
65 years. www.collinsinst.com
Plastic valves and actuators from Collins
CHEMICAL ENGINEERING||||WWW.CHEMENGONLINE.COM||||SEPTEMBER 2014||||||73
Water Management Special Advertising Section
Not all scale inhibitors are created equally
Polymer chemistries from BWA Water Additives give a one-two punch against scales,
where traditional phosphonates or very low molecular weight polymers fail
B
WA Water Additives is a technology-
led specialty chemicals company that
focuses on providing sustainable solutions
in water treatment challenges. Whether it
is scale control, corrosion inhibition, mi-
crobiological control or desalination, BWA
has unique chemistries providing solutions
in increasingly extreme environments.
Scale inhibition is a concern for any
process that uses water, from industrial
treatment, though cooling towers and
geothermal energy, to oil and gas produc-
tion. These environments can have water
chemistries that rapidly change, as well
as physical characteristics such as tem-
perature that can fluctuate greatly in mere
hours. Traditional scale inhibitors, based
in phosphonates or very low molecular
weight polymers, are prone to failure in
such applications because of the types of
inhibitory mechanisms they depend on.
In particular, scaling caused by barium
sulfate can be difficult to control. Once
nucleation has begun, it can very rapidly
seize up a pipe, resulting in a significant
loss of money in terms of both system
downtime and maintenance efforts. The
resulting scale is not easily removed, and
often results in the need to either drill out
the blockage or simply replace the pipe. In
a low-pH environment the problem seems
to be compounded by standard scale in-
hibitors, which fail at an even faster rate.
BWAs Bellasol S50, on the other hand,
has proven itself time and again in these
types of environments as a cost-effective
water treatment.
A growing concern that needs to be ac-
knowledged is that scale inhibition prod-
ucts must now be able not only to protect
and maintain the functionality of a sys-
tem, but to do so in an environmentally-
friendly, biodegradable fashion. BWA
Water Additives Belclene 810 has strong
antiscalant properties in calcium carbon-
ate, barium sulfate and even mixed scales,
while scoring high in the OECD 302B bio-
degradation test.
BWA Water Additives scale inhibition
polymers work where phosphonates can
fail because they block crystal growth and
provide threshold inhibition, while having
great thermal stability properties over a
wide pH spectrum. BWAs polymeric scale
inhibitors can provide the needed solution
to common scales such as calcium carbon-
ate, barium sulfate, harder-to-treat silica
scales, and even heavy metals.
www.wateradditives.com
Poorly controlled scale can quickly
block pipes so badly that replacement
may be the only practical option
An intelligent approach to measurement
OTEK Corp. manufactures panel instruments that combine traditional visibility with
modern digital accuracy and reliability
M
anufacturers rely on digital process
instruments to maintain accuracy and
consistency in their processes. For many
processes, including water treatment, even
a small inaccuracy in a variable can have a
significant effect on the desired product.
Variations in temperature, flow, propor-
tion, and other parameters must be care-
fully monitored and controlled.
OTEK Corp., a leading designer and
manufacturer of digital instrumentation,
knows that accuracy is required to maxi-
mize its customers profitability and en-
sure quality and safety. Its instruments are
manufactured with the latest technology to
ensure accurate and reliable performance,
and durable products.
The NTM series is the latest in digital
panel meters from OTEK. The series in-
cludes 19 different models available with
loop, signal or external power. The use of
high-efficiency components allows OTEK
to produce a product with lower power
consumption than the current industry av-
erage. A lower power requirement permits
the display to maintain an even intensity at
both the high and low end of the 420 mA
range. Units are equipped with an LED digi-
tal display and a tri-color bar graph to en-
sure visibility. The bar graph also shows
the current setpoints in color.
OTEK offers a signal failure detection
feature in all of its units. If a sensor fails or
a cable breaks, the display will flash the
message INPT FAIL for approximately
20 s to alert the user. It then transmits a
failure notification to the supervisory con-
trol system, before going dark.
The innovative designs incorpo-
rate flexible firmware for improved
customization. Depending on the model
and the input selection, the NTM series
offers a wide variety of options. For in-
stance, one channels setpoint can be
used to control another channels function.
Isolated serial I/O is available, and there is
a choice of USB, RS485, Ethernet or IRDA.
Added benefits include remote display for
SCADA/DCS, improved response time, and
self-diagnostics.
The series offers replacements for vir-
tually all existing analog and digital me-
ters. Easy pin-for-pin replacement means
no rewiring and no need to run additional
power to the unit. NTM meters have no
moving parts so there is no longer a need
for recalibration and maintenance.
OTEK Corp. backs all its instruments
with a lifetime warranty that is unique to
the industry. www.otekcorp.com
A combination of digital and bar graph
displays provides maximum information
PRODUCT
SHOWCASE
Circle 202 on p. 76 or go to
adlinks.che.com/50980-202
Circle 201 on p. 76 or go to
adlinks.che.com/50980-201
Circle 203 on p. 76 or go to
adlinks.che.com/50980-203
PTFE or FKM
diaphragms.
PVC, Polypro or
PVDF bodies.
Available with
or without
gauges.
Gauge
Shields for
harsh environments.
PLAST-O-MATIC VALVES, INC.
CEDAR GRVE, M1 0Z00
[Z3J 253000 Fox: [Z3J 254Z45
www.plos|omo|ic.com inlo@plos|omo|ic.com
Compact and Economical, Plast-O-Matic
Gauge Guards prevent dangerous leaks and
allow dependable instrument readings from
full vacuum to 250 psi.
Protect pressure or vacuum
instruments from clogging,
corrosion and damage.
Model A100
Plug Resistant
Orifice for critical
drain lines
CU Services LLC
725 Parkview Cir,
Elk Grove Vlg, Il 60007
Phone 847-439-2303
[email protected]
www.cuservices.net
When a plugged
drain line would
mean disaster...
www.neuhaus-neotec.de
Process
Technology
Grinding
Process
Technology
Grinding
www.neuhaus-neotec.de
Circle 241 on p. 76 or go to
adlinks.che.com/50980-241
CONSULTING
Circle 243 on p. 76 or go to
adlinks.che.com/50980-243
Engineering e-material, e-solutions, e-courses
and e-seminars for energy conversion systems:
Fhysical Froerties Steam Aroximations
Fower Cycles Fower Cycle Comonents/Frocesses
Comressible Flow
ENGINEERING SOFTWARE
Phone/FAX: (301) 540-3605
Web Site: http://www.engineering-4e.com
Visit the web site to check out free demos, etc.!
SOFTWARE
Circle 250 on p. 76 or go to
adlinks.che.com/50980-250
Circle 244 on p. 76 or go to
adlinks.che.com/50980-244
CRYSTALLIZATION &
PRECIPITATION
Dr. Wayne J. Genck
Genck International
3 Somonauk Court, Park Forest, IL. 60466
Tel (708) 748-7200 Fax (708) 748-7208
[email protected] http://www.genckintl.com
Design/ScaIe-up Purity
Size Distribution Caking
Laboratory Investigations Drying
FiItration ParticIe Habit
TroubIeshooting PoIymorphism
Product Micro-AnaIysis Kinetics Studies
IndustriaI Seminars
74 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 75
NEW & USED EQUIPMENT
Circle 248 on p. 76 or go to
adlinks.che.com/50980-248
Scan to learn more
& get a free quote.
Free Tag Reader:
http://gettag.mobi
CONTROL
SYSTEMS
Recipe-controlled. IQ/OQ. CIP/SIP.
Fast design/install. Reliable support.
1-866-797-2660
www.RossSysCon.com
Circle 247 on p. 76 or go to
adlinks.che.com/50980-247
KnightHawk Engineering
Specialists in design, failure analysis
and troubleshooting of static
and rotating equipment
www.knighthawk.com
Contact Jim Salter 281-282-9200
Circle 249 on p. 76 or go to
adlinks.che.com/50980-249
Circle 252 on p. 76 or go to
adlinks.che.com/50980-252
HEAT EXCHANGERS
Liquid Cooled
Air Cooled

FOR
GASES & LIQUIDS!
Talk Directly with Design Engineers!
BIower CooIing Vent Condensing
(952) 933-2559 [email protected]
Circle 242 on p. 76 or go to
adlinks.che.com/50980-242
-From 100 to 1,000,000 LBS
-The solution for problematic products
-As fine as 10 Micron
-Excellent yields with quick turn around
-Super high efficiencies
TEL:(914)381-7500 or Toll Free:1-800-AT ELCAN
20 MARBLEDALE ROAD, TUCKAHOE, NY 10707
[email protected]
Circle 245 on p. 76 or go to
adlinks.che.com/50980-245
Circle 251 on p. 76 or go to
adlinks.che.com/50980-251
WABASH SELLS & RENTS
Boilers
20,000 - 400,000 #/Hr.
Diesel & Turbine Generators
50 - 25,000 KW
Gears & Turbines
25 - 4000 HP
We stock large inventories of:
Air Pre-Heaters Economizers Deaerators
Pumps Motors Fuel Oil Heating and Pump Sets
valves Tubes Controls Compressors
Pulverizers Rental Boilers & Generators
24/7 Fast Emergency Service
800-704-2002
Phone: 847-541-5600 Fax: 847-541-1279
www.wabashpower.com
POWER EQUIPMENT CO.
444 Carpenter Ave., Wheeling, IL 60090
wabash
Circle 246 on p. 76 or go to
adlinks.che.com/50980-246
SS 304,316,317, Alloy20, Monel, ChromeMoly, Titanium,
Brass, Steel, Duplex... IN STOCK, MADE IN USA
JOHN R. ROBINSON INC.
Phone #1-800-726-1026
www.johnrrobinsoninc.com
[email protected]
HEAT EXCHANGER TUBE PLUGS
Interested?
For more information
on classified advertising,
please contact:
Diane Burleson
Email: [email protected]
Tel: 512.337-7890 Fax: 512.213.4855
Advertise in the Classified Advertise in the Classified
CLASSI FI ED ADVERTI SI NG THAT WORKS
76 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
FREE PRODUCT INFO
(please answer all the questions)
YOUR INDUSTRY
01 Food & Beverages
02 Wood, Pulp & Paper
03 Inorganic Chemicals
04 Plastics, Synthetic Resins
05 Drugs & Cosmetics
06 Soaps & Detergents
07 Paints & Allied Products
08 Organic Chemicals
09 Agricultural Chemicals
10 Petroleum Refning,
Coal Products
11 Rubber & Misc. Plastics
12 Stone, Clay, Glass, Ceramics
13 Metallurgical & Metal Products
14 Engineering, Design & Construc-
tion Firms
15 Engineering/Environmental Ser-
vices
16 Equipment Manufacturer
17 Energy incl. Co-generation
18 Other

JOB FUNCTION
20 Corporate Management
21 Plant Operations incl. Mainte-
nance
22 Engineering
23 Research & Development
24 Safety & Environmental
26 Other

EMPLOYEE SIZE
28 Less than 10 Employees
29 10 to 49 Employees
30 50 to 99 Employees
31 100 to 249 Employees
32 250 to 499 Employees
33 500 to 999 Employees
34 1,000 or more Employees
YOU RECOMMEND,
SPECIFY, PURCHASE
(please circle all that apply)
40 Drying Equipment
41 Filtration/Separation Equipment
42 Heat Transfer/Energy Conserva-
tion Equipment
43 Instrumentation & Control Sys-
tems
44 Mixing, Blending Equipment
45 Motors, Motor Controls
46 Piping, Tubing, Fittings
47 Pollution Control Equipment
& Systems
48 Pumps
49 Safety Equipment & Services
50 Size Reduction & Agglomeration
Equipment
51 Solids Handling Equipment
52 Tanks, Vessels, Reactors
53 Valves
54 Engineering Computers/Soft-
ware/Peripherals
55 Water Treatment Chemicals
& Equipment
56 Hazardous Waste Management
Systems
57 Chemicals & Raw Materials
58 Materials of Construction
59 Compressors
Fax this page back to 800-571-7730
New Product Information September 2014
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
If number(s) do not appear above,
please write them here and circle:
Name Title
Company
Address
City State/Province Zip/Postal Code
Country\ Telephone Fax
Email | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

ADVERTISING SALES REPRESENTATIVES

International
Petra Trautes
Chemical Engineering
Zeilweg 44
D-60439 Frankfurt am Main
Germany
Phone: +49-69-58604760
Fax: +49-69-5700-2484
Email: [email protected]
Austria, Czech Republic, Benelux,
Eastern Europe, Germany, Scandinavia,
Switzerland, United Kingdom
Dipali Dhar
Chemical Engineering
88 Pine Street, 5th foor, New York, NY 10005
Tel: 718-263-1162
E-mail: [email protected]
India
Katshuhiro Ishii
Chemical Engineering
Ace Media Service Inc., 12-6, 4-chome
Nishiiko, Adachi-ku, Tokyo 121, Japan
Tel: 81-3-5691-3335; Fax: 81-3-5691-3336
E-mail: [email protected]
Japan
Ferruccio Silvera
Chemical Engineering
Silvera Pubblicita
Viale Monza, 24 Milano 20127, Italy
Tel: 39-02-284-6716;
Fax: 39-02-289-3849
E-mail: [email protected]/www.
silvera.it
Andorra, France, Gibraltar, Greece,
Israel, Italy, Portugal, Spain
Rudy Teng
Sales Representative
Chemical Engineering;
8F-1 #181 Wulin Road
Hsinchu 30055 Taiwan
Tel: +86 13818181202, (China),
+886 921322428 (Taiwan)
Fax: +86 21 54183567
E-mail: [email protected]
Asia-Pacifc, Hong Kong, Peoples
Republic of China, Taiwan
North America
Terry Davis
Sales Director
Chemical Engineering
2276 Eastway Rd., Decatur, GA 30033
Tel: 404-634-5123; Fax: 832-201-8823 E-mail: [email protected]
Alabama, Canada, Connecticut, Delaware, Georgia, Idaho,
Kentucky, Latin America, Maine, Maryland, Massachusetts,
Mississippi, Montana, Nebraska, New Hampshire, New Jersey,
New York, North and South Carolina, North and South Dakota,
Ohio, Oregon, Pennsylvania, Rhode Island, Tennessee, Utah,
Vermont, Virginia, Washington D.C., West Virginia, Wyoming
Diane Burleson
Inside Sales Manager
Chemical Engineering;
11000 Richmond Ave, Suite 690,
Houston, TX 77042
Tel: 512-337-7890
E-mail: [email protected]
Product Showcase,
Literature Reviews,
Classifed Display Advertising
Dan Gentile
District Sales Manager
Tel: 512-918-8075
E-mail: [email protected]
Alaska, Hawaii, Illinois,
Indiana, Iowa, Michigan,
Minnesota, Wisconsin,
Jason Bullock,
District Sales Manager
Chemical Engineering
8325 Broadway, Ste. 202/PMB 261
Pearland, TX 77581
Tel: 281-485-4077; Fax: 281-485-1285
E-mail: [email protected]
Arizona, Arkansas, California,
Colorado, Florida, Kansas, Louisiana,
Missouri, Nevada, New Mexico,
Oklahoma, Texas, Washington
Fill out the form and circle or write in the number(s)
below, cut it out, and fax it to 800-571-7730.
Go on the Web and fll out the
online reader service card.
JustFAXit! or go to www.chemengonline.com/adlinks
CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 77
Advertisers Index
3P Prinz 39
adlinks.che.com/50980-01
Abbe, Paul O. 43
1-800-524-2188 adlinks.che.com/50980-04
* Alexanderwerk GmbH 32I-8
49 (0) 2191 795 0 adlinks.che.com/50980-05
AMACS Process Tower Internals 21
1-281-716-1179 adlinks.che.com/50980-06
* Arca-Reglar GmbH 32I-4
49-2156-7709-0 adlinks.che.com/50980-07
AUMA Riester GmbH & Co. KG 23
adlinks.che.com/50980-08
BASF 15
adlinks.che.com/50980-09
Berndorf Band GmbH 13
1-847-841-3300 adlinks.che.com/50980-10
Beumer Group GmbH & Co. KG 9
adlinks.che.com/50980-11
Buss-SMS-Canzler 24
49 60 33-85-0 adlinks.che.com/50980-12
BWA Water Additives 50
adlinks.che.com/50980-13
Carver Pump Company 30
1-563-263-3410 adlinks.che.com/50980-14
Cashco VCI 14
1-785-472-3539 adlinks.che.com/50980-15
Chemineer 16
1-800-643-0641 adlinks.che.com/50980-16
Collins Instrument Co. 17
1-979-849-8266 adlinks.che.com/50980-17
Corzan HP Piping Systems 29
1-216-447-7397 adlinks.che.com/50980-32
Dow Water & SECOND
Process Solutions COVER
adlinks.che.com/50980-18
Dunn Heat Exchangers 20
1-409-948-1704 adlinks.che.com/50980-19
Eastman Chemical Company 3
1-800-426-2463 adlinks.che.com/50980-20
Emerson Process FOURTH
Management COVER
Federal Equipment Co. 38
1-877-503-9745 adlinks.che.com/50980-21
Fike Corporation 31
1-877-814-3453 adlinks.che.com/50980-22
Fluid Metering Inc. 39
1-800-223-3388 adlinks.che.com/50980-23
GEA Heat Exchangers/HX
Holding GmbH 27
adlinks.che.com/50980-24
* GEA Process Engineering A/S 32I-5
49 39 54 54 54 adlinks.che.com/50980-25
GEM Valves 42
1-678-553-3400 adlinks.che.com/50980-26
Heat Transfer Research, Inc. 40
adlinks.che.com/50980-27
Inline Industries 32
1-800-568-8998 adlinks.che.com/50980-28
* Italvacuum 32I-6
adlinks.che.com/50980-29
* KSB AG 32I-3
adlinks.che.com/50980-30
Load Controls 64
1-888-600-3247 adlinks.che.com/50980-31
Miller-Stephenson 8
1-800-992-2424 adlinks.che.com/50980-33
Mller GmbH 6
49 (0) 7623/969-0 adlinks.che.com/50980-34
Otek Corporation 18
1-520-748-7900 adlinks.che.com/50980-35
Outotec (Finland) Oy 7
adlinks.che.com/50980-36
* Plast-O-Matic Valves, Inc. 32I-7
1-973-256-3000 adlinks.che.com/50980-37
Plymouth Tube Co. 22
adlinks.che.com/50980-38
Pompetravaini Spa 55
39.0331.889000 adlinks.che.com/50980-39
Quest Integrity Group 49
1-253-893-7070 adlinks.che.com/50980-40
RedGuard 28, 34
1-855-REDGUARD
adlinks.che.com/50980-02, 03
Rembe GmbH 49
49 (0) 29 61-7405-0 adlinks.che.com/50980-41
Roper Pump Co. 65
1-706-335-5551 adlinks.che.com/50980-42
Ross, Charles & Son Company 10
1-800-243-ROSS adlinks.che.com/50980-43
Roto Hammer Industries, Inc. 8
1-800-477-7686 adlinks.che.com/50980-44
Sandvik Process Systems 35
49 711 5105-0 adlinks.che.com/50980-45
SoundPLAN International LLC 6
1-360-432-9840 adlinks.che.com/50980-46
Team Industrial Services 25
1-800-662-8326 adlinks.che.com/50980-47
United Rentals 4
adlinks.che.com/50980-48
Advertiser Page number
Phone number Reader Service #
Advertiser Page number
Phone number Reader Service #
Advertiser Page number
Phone number Reader Service #
Send Advertisements and Box replies to: Diane Burleson
Chemical Engineering, 11000 Richmond Ave, Houston, TX 77042
E-mail: [email protected] Tel: 512-337-7890
* International Edition
See bottom of opposite page
for advertising
sales representatives'
contact information
Classifed Index September 2014
Advertiser Page number
Phone number Reader Service #
Advertiser's Product
Showcase . . . . . . . . . . . . . . . . . . . . . 74
Computer Software . . . . . . . . . . . . . 74
Consulting . . . . . . . . . . . . . . . . . . . . 74
Equipment, New & Used . . . . . . . . . 75
Plast-O-Matic Valves, Inc. 74
1-973-256-3000 adlinks.che.com/50980-203
Ross, Charles & Son Company 75
1-800-243-ROSS adlinks.che.com/50980-248
Vesconite Bearings 75
27 11 616 11 11 adlinks.che.com/50980-249
VisiMix 74
972 52 383 4174 adlinks.che.com/50980-250
Wabash Power Equipment Co. 75
1-800-704-2002 adlinks.che.com/50980-251
Xchanger, Inc. 75
1-952-933-2559 adlinks.che.com/50980-252
Advertiser Page number
Phone number Reader Service #
Applied e-Simulators Software 74
adlinks.che.com/50980-241
CU Services LLC 74
1-847-439-2303 adlinks.che.com/50980-201
Elcan Industries 75
1-914-381-7500 adlinks.che.com/50980-242
Engineering Software 74
1-301-540-3605 adlinks.che.com/50980-243
Genck International 74
1-708-748-7200 adlinks.che.com/50980-244
Indeck Power Equipment Co. 75
1-847-541-8300 adlinks.che.com/50980-245
John R. Robinson, Inc. 75
1-800-726-1026 adlinks.che.com/50980-246
KnightHawk Engineering 75
1-281-282-9200 adlinks.che.com/50980-247
Neuhaus Neotec 74
adlinks.che.com/50980-202
78 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
People
Specialty chemicals producer
Lanxess (Cologne, Germany) names
Matthias Zachert chairman of the
board, and promotes Jorge Nogueira
to head of the Performance Butadiene
Rubbers business unit.
The Sensors Div. of Honeywell Life
Safety (Morris Township, N.J.)
appoints Sean Clay general manager
and Alexandre Naef sales leader.
Finder Pompe S.p.A. (Merate, Italy),
which recently became part of Dover
Corp.s Pump Solutions Group
(Oakbrook Terrace, Ill.), names
Lorenzo Barbieri CEO.
Victor Ferris becomes president and
CEO of HRST, Inc. (Eden Prairie,
Minn.), a provider of products and
services to power plants and indus-
trial facilities. Andrew Kubly is now
the companys chief financial officer.
Siluria Technologies (San Fran-
cisco, Calif.), a developer of commer-
cial processes for producing fuels and
chemicals from natural gas, names
Karl Kurz chairman of the board.
Dan Kieny joins Black & Veatch
(Overland Park, Kan.) as chief infor-
mation officer and senior vice
president.
Vimal Kapur becomes CEO of Hon-
eywell Process Solutions (Morris
Township, N.J.), which supplies pro-
cess automation, control and instru-
mentation solutions.
Gary McArthur joins CH2M Hill
(Denver, Colo.) as executive vice pres-
ident and chief financial officer.
Suzanne Shelley
Clay Kieny Barbieri Naef
SEPTEMBER WHOS WHO
Ferris
SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE
SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE
SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE
SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE
SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE SUBSCRIBE
S U B S C R I B E T O
Written for engineers, by engineers
More and more, business in the Chemical Process Industries (CPI) is not
local, its global. To keep up with this rapidly evolving marketplace, you
need a magazine that covers it all, not just one country or region, not just
one vertical market, but the whole CPI.
With editorial ofces in Europe, Asia, and North America, CHEMICAL
ENGINEERING is well-positioned to keep abreast of all the latest innovations
in the equipment, technology, materials, and services used by process
plants worldwide. No other publication even comes close.
To subscribe, please call 1-847-564-9290
or visit [email protected]
www.chemengonline.com
The #1 choice
of worldwide
CPI organizations
Economic Indicators
September 2014; VOL. 121; NO. 9
Chemical Engineering copyright @ 2014 (ISSN 0009-2460) is published monthly by Access Intelligence, LLC, 4 Choke Cherry Road, 2nd Floor, Rockville, MD, 20850. Chemical
Engineering Executive, Editorial, Advertising and Publication Ofces: 88 Pine Street, 5th Floor, New York, NY 10005; Phone: 212-621-4674, Fax: 212-621-4694. Subscription rates:
$149.97 U.S. and U.S. possessions, $166.97 Canada, and $269 International. $20.00 Back issue & Single copy sales. Periodicals postage paid at Rockville, MD and additional
mailing ofces. Postmaster: Send address changes to Chemical Engineering, Fulllment Manager, P.O. Box 3588, Northbrook, IL 60065-3588. Phone: 847-564-9290, Fax: 847-
564-9453, email: [email protected]. Change of address, two to eight week notice requested. For information regarding article reprints, please contact Wrights Media,
1-877-652-5295, [email protected]. Contents may not be reproduced in any form without written permission. Canada Post 40612608. Return undeliverable Canadian
Addresses to: IMEX Global Solutions, P.O. BOX 25542, LONDON, ON N6C 6B2
FOR ADDITIONAL NEWS AS IT DEVELOPS, PLEASE VISIT WWW.CHEMENGONLINE.COM
PLANT WATCH
Jacobs awarded contract for ExxonMobil
projects in Baytown and Mont Belvieu
August 12, 2014 Jacobs Engineering
Group Inc. (Pasadena, Calif.; www.jacobs.
com) was awarded a contract from Exxon-
Mobil Chemical Co. to provide engineering,
procurement and construction services as
part of an ethane-cracker project in Exxon-
Mobils Baytown, Tex. complex, and associ-
ated premium product facilities in Mont Bel-
vieu, Tex. Company officials did not disclose
the contract value.
Clariant plans to build new
masterbatches plant in Australia
August 12, 2014 Clariant AG (Muttenz,
Switzerland; www.clariant.com) plans to
build a new masterbatches plant in Sydney,
Australia. The new plant will mainly serve the
Australian market. Construction on the plant
is currently underway, with commissioning
scheduled for the fourth quarter 2014.
Ashland to expand capacity for
hydroxyethylcellulose capacity Nanjing
August 4, 2014 Ashland Inc. (Covington,
Ky.; www.ashland.com) plans to expand
capacity at its hydroxyethylcellulose pro-
duction facility in the Nanjing Chemical
Industrial Park by 4,000 metric tons (m.t.), or
approximately 40%, over the next 18 months.
The additional capacity will come online in
two phases. The first 2,000 m.t. will be avail-
able in early 2015 and the second 2,000 m.t.
will be available in late 2015.
Polyamide 6 plant commissioned for
Hangzhou Hangding Nylon Tech.
August 1, 2014 Uhde Inventa-Fischer
GmbH (Berlin, Germany; www.uhde-inventa-
fischer.com) and Hangzhou Hangding
Nylon Tech. Co. have commissioned a plant
for the production of high-performance
polyamide 6 for textile-grade applications.
The plant is located in Hangzhou City in Zhe-
jiang Province, China and has a production
capacity of 47,000 m.t./yr.
Arkema starts up methyl acrylate
plant in Clear Lake, Tex.
July 28, 2014 Arkema (Colombes, France;
www.arkema.com) has started up a new
plant for the production of methyl acrylate
at its Clear Lake, Tex. site, representing the
last phase of a $110-million investment plan.
The new methyl acrylate plant has a capac-
ity of 45,000 m.t./yr.
Tesoro announces plans for xylenes
production in the U.S.
July 22, 2014 Tesoro Corp. (San Antonio,
Tex.; www.tsocorp.com) intends to gather
intermediate feedstock, primarily reformate,
from its West Coast refining system for xy-
lene extraction at Anacortes, Wash. The
initial investment is estimated to be around
$400 million. Startup of the new facilities is
expected in 2017, subject to permitting and
approval processes.
Evonik invests in new plant in Brazil for
the production of precipitated silicas
July 21, 2014 Evonik Industries AG (Essen,
Germany; www.evonik.com) plans to build
a plant to produce precipitated silicas in
So Paulo, Brazil. The plant is scheduled to
go onstream in 2016. This is said to be the first
production plant for highly dispersible silica
in South America.
Topse opens new sulfuric-acid-catalyst
production plant in Bayport, Tex.
July 18, 2014 Haldor Topse A/S (Lyngby,
Denmark; www.topsoe.com) opened a new
plant at its production site in Bayport, Tex.
The plant is devoted to producing Topses
VK portfolio of extruded catalysts, which are
used for the production of sulfuric acid.
MERGERS AND ACQUISITIONS
Borealis takes full ownership of
specialty polymers JV
August 7, 2014 Borealis AG (Vienna,
Austria: www.borealisgroup.com) will take
full ownership of the Specialty Polymers
Antwerp N.V. joint venture (JV) by purchas-
ing a 67% share from DuPont Holding Neth-
erlands B.V. The transaction is subject to
approval by the relevant authorities.
Yara acquires majority position in
Brazilian fertilizer company Galvani
August 5, 2014 Yara International ASA (Os-
lo, Norway; www.yara.com) has acquired a
60% stake in Galvani Indstria, Comrcio e
Servios S/A for an enterprise value of $318
million. Galvani is an independent, privately
held fertilizer company engaged in phos-
phate mining, production and distribution
of fertilizers in Brazil.
Mexichem acquires German
PVC specialist Vestolit
August 5, 2014 Mexichem S.A.B. de C.V.
(Tlalnepantla, Mexico; www.mexichem.
com) has signed a definitive agreement to
acquire polyvinyl chloride (PVC) producer
Vestolit GmbH (Marl, Germany; www.vestolit.
de) from Strategic Value Partners LLC. The
acquisition is subject to regulatory approv-
als and is expected to close in the fourth
quarter of 2014.
Solvay to sell its Eco Services
sulfuric-acid business for $890 million
July 31, 2014 Solvay S.A. (Brussels, Bel-
gium; www.solvay.com) has agreed to sell
its Eco Services business, which specliazes in
sulfuric-acid virgin production and regener-
ation, to affiliates of CCMP Capital Advisors,
LLC for an enterprise value of $890 million.
Completion of the transaction is expected
in the fourth quarter of 2014.
Showa Denko to acquire high-purity
chlorine business from Air Products
July 31, 2014 Showa Denko K.K. (Tokyo,
Japan; www.sdk.co.jp) subsidiary Taiwan
Showa Chemicals Manufacturing Co. has
come to an agreement with Air Products
San Fu Co. (APSF), a subsidiary of Air Prod-
ucts and Chemicals Inc.(Lehigh Valley, Pa.;
www.airproducts.com), to acquire APSFs
high-purity chlorine business, including its
production facility in Kaohsiung, Taiwan.
Outotec acquires the business of
Kalogeo Anlagenbau
July 28, 2014 Outotec Oyj (Espoo, Fin-
land; www.outotec.com) has purchased
the assets of Kalogeo Anlagenbau GmbH
(Leobersdorf, Austria). Kalogeo provides
solutions for biomass, sludge and wastewa-
ter-treatment and has designed, built and
operated several mid-size thermal sludge-
treatment plants based on fluidized-bed
technology. Outotec plans to expand the
acquired businesss annual sales to approxi-
mately 1520 million beginning in 2016.
Albemarle to acquire Rockwood
Holdings for $6.2 billion
July 15, 2014 Albemarle Corp. (Baton
Rouge, La.; www.albemarle.com) and Rock-
wood Holdings, Inc. have entered into a de-
finitive agreement under which Albemarle
will acquire all outstanding shares of Rock-
wood in a transaction valued at approxi-
mately $6.2 billion. This combination creates
a company with positions across the lithium,
catalysts, bromine and surface-treatment
sectors. The transaction is expected to close
in the first quarter of 2015.
Mary Page Bailey
BUSINESS NEWS
FOR MORE ECONOMIC INDICATORS, SEE NEXT PAGE CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014 79
Economic Indicators
500
525
550
575
600
625
J F M A M J J A S O N D
DOWNLOAD THE CEPCI TWO WEEKS SOONER AT WWW.CHEMENGONLINE.COM/PCI
CURRENT TRENDS
T
he preliminary value for the June
CE Plant Cost Index (CEPCI; top;
the most recent available) rose 0.3%
from the final May value, after gains
the previous two months. Subcat-
egories of the equipment index
generally saw small increases, or
were relatively flat. The most signifi-
cant increase came in the Process
Machinery subindex. The Construc-
tion Labor index declined slightly in
the June preliminary numbers, while
the Buildings and Engineering &
Supervision subindexes rose slightly.
The overall June PCI value stands
at 2.0% higher than its value from
June 2013. Meanwhile, updated
values for the Current Business Indi-
cators (CBI) from IHS Global Insight
(middle) saw small increases in all
CBI categories.
HIGHLIGHTS FROM RECENT ACC ECONOMIC DATA
T
he July Chemical Activity Barometer (CAB), a leading economic indicator created by the
American Chemistry Council (ACC; Washington, D.C.; www.americanchemistry.com)
posted a 0.4% increase over June, as measured on a three-month moving average (3MMA)
basis. Look for updated CAB information on our website (www.chemengonline.com). The
pace of growth was consistent with earlier growth logged in the second quarter. Year-over-
year growth now stands at a 4.4% increase. Uncertainty in global energy markets kept the
non-adjusted barometer at a slow 0.1% gain in June, but provisional data suggest there is
room for further expansion in coming months, the ACC said.
In one of its recent Weekly Chemistry and Economic Reports, ACC noted that exports of
chemicals from the U.S. rose 3.2% in June to $16.7 billion, while imports were down 2.4%
to $16.4 billion. Excluding pharmaceuticals, chemical exports were up 0.8% to $12.0 bil-
lion, and imports were down 3.8% to $8.5 billion. The trade balance moved from deficit to
surplus in June, the report said, adding, Excluding pharmaceuticals, the [U.S.] chemical
industry continues to post a large trade surplus.
In another recent report, ACC said the Global Chemical Production Regional Index
(Global CPRI) was flat for the second month in a row in June, on a 3MMA basis. This in-
dicates that growth stalled in the second quarter of 2014, with activity only slightly higher
than the first quarter, the report said.
Meanwhile, the U.S. CPRI rose 0.3% in June, with chemical output higher in all geographic
regions, the ACC said. The June gain follows a 0.5% rise in May.
2012 2013 2014
CHEMICAL ENGINEERING PLANT COST INDEX (CEPCI)
(195759 = 100)
June 14
Prelim.
May 14
Final
June 13
Final
CE Index
576.2 574.3 564.8
Equipment 700.1 697.0 684.1
Heat exchangers & tanks 638.1 635.1 626.7
Process machinery 673.8 665.0 654.4
Pipes, valves & fittings 880.3 876.2 859.3
Process instruments 411.0 410.8 410.1
Pumps & compressors 938.2 938.6 919.2
Electrical equipment 515.3 515.3 512.7
Structural supports & misc 770.0 767.4 730.9
Construction labor 319.7 320.5 317.3
Buildings 543.4 543.2 530.7
Engineering & supervision 321.1 321.0 323.9
CURRENT BUSINESS INDICATORS*
LATEST PREVIOUS YEAR AGO
CPI output index (2007 = 100) Jul.'14 = 91.9 Jun.'14 = 91.4 May '14 = 90.6 Jul.'13 = 88.9
CPI value of output, $ billions Jun.'14 = 2,167.0 May '14 = 2,150.6 Apr.'14 = 2,156.4 Jun.'13 = 2,109.4
CPI operating rate, % Jul.'14 = 77.3 Jun.'14 = 76.9 May '14 = 76.4 Jul.'13 = 75.7
Producer prices, industrial chemicals (1982 = 100) Jul.'14 = 293.2 Jun.'14 = 288.9 May '14 = 288.4 Jul.'13 = 299.8
Industrial Production in Manufacturing (2007 = 100) Jul.'14 = 100.7 Jun.'14 = 99.8 May '14 = 99.5 Jul.'13 = 96.0
Hourly earnings index, chemical & allied products (1992 = 100) Jul.'14 = 157.4 Jun.'14 = 156.8 May '14 = 155.2 Jul.'13 = 156.8
Productivity index, chemicals & allied products (1992 = 100) Jul.'14 = 108.5 Jun.'14 = 107.6 May '14 = 107.4 Jul.'13 = 106.0
70
72
74
76
78
80
1800
1900
2000
2100
2200
2300
J F M A M J J A S O N D J F M A M J J A S O N D J F M A M J J A S O N D
75
80
85
90
95
100
CPI OUTPUT INDEX (2007 = 100) CPI OUTPUT VALUE ($ BILLIONS) CPI OPERATING RATE (%)
*Current Business Indicators provided by IHS Global Insight, Inc., Lexington, Mass.
Annual
Index:
2006 = 499.6
2007 = 525.4
2008 = 575.4
2009 = 521.9
2010 = 550.8
2011 = 585.7
2012 = 584.6
2013 = 567.3
80 CHEMICAL ENGINEERING WWW.CHEMENGONLINE.COM SEPTEMBER 2014
Order your copy today by visiting store.che.com
This guidebook contains how-to engineering articles formerly published in Chemical Engineering. The
articles in Volume 2 provide practical engineering recommendations for process operators faced with the
challenge of treating inlet water for process use, and treating industrial wastewater to make it suitable for
discharge or reuse.
There is a focus on the importance of closed-loop or zero-discharge plant design, as well as the selection,
operation and maintenance of membrane-based treatment systems; treating water for use in recirculated-
water cooling systems; managing water treatment to ensure trouble-free steam service; designing stripping
columns for water treatment; and more.
Table of Contents
Process Water Treatment Challenges and Solutions
Water Reuse and Conservation in the CPI
Strategies to Minimize Wastewater Discharge
Strategies for Water Reuse
Wastewater: A Reliable Water Resource
Membranes for Process Water Reuse
Strategies for Controlling Membrane Fouling
Fact at Your Fingertips: Membranes
Facts at Your Fingertips: Membrane Congurations
Facts at Your Fingertips: Controlling Membrane Fouling
Biodegradation and Testing of Scale Inhibitors
Keeping Cooling Water Clean
Caring for Cooling Water Systems
Purifying Coke-Cooling Wastewater
Non-Chemical Water Treatment
CPI Water and Steam Chemistry
Designing Steam Stripping Columns for Wastewater
Process Water and Wastewater Treatment
and Reuse Guidebook- Volume 2
Now Available in the Chemical Engineering Store:
20611
YOU CAN DO THAT
Electronic marshalling eliminates the rework, the redesign and the headaches.
With DeltaV Electronic Marshalling, Emerson lets you make I/O changes where and when you need
them without costly engineering and schedule delays. Our new DeltaV CHARacterization Module
(CHARM) completely eliminates the cross-wiring from the marshalling panel to the I/O cardregardless of signal
typeso youre no longer held to predefined specifications. All those wires, gone. All that time and engineering, gone.
See how easy it can be by scanning the code below or by visiting OonDemandCalculator.com
The Emerson logo is a trademark and a service mark of Emerson Electric Co. 2012 Emerson Electric Co.
Another I/O change? Great.
So another wiring schedule.
Another marshalling design.
And another cabinet...
Just make it all go away!