Scribd
Upload
9K views

Half Wave Rectifier Circuit

The document describes a student project to build a half wave rectifier circuit. It lists the purpose as allowing students to make and understand how a rectifier circuit works. It provides materials needed, including an oscilloscope, transformer, diode, multimeter, regulator, filter, wires and resistors. The procedure explains how to calibrate the oscilloscope, build the circuit without and with a filter, and measure test points to see the waveforms. Data pictures show the input alternating current wave, output direct current wave after rectification, rippled output of the filter and flat output of the regulator. The conclusion states that a half wave rectifier circuit uses a diode, filter and regulator to change a half wave signal into a constant

Uploaded by

yopyprasetya
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
9K views

Half Wave Rectifier Circuit

The document describes a student project to build a half wave rectifier circuit. It lists the purpose as allowing students to make and understand how a rectifier circuit works. It provides materials needed, including an oscilloscope, transformer, diode, multimeter, regulator, filter, wires and resistors. The procedure explains how to calibrate the oscilloscope, build the circuit without and with a filter, and measure test points to see the waveforms. Data pictures show the input alternating current wave, output direct current wave after rectification, rippled output of the filter and flat output of the regulator. The conclusion states that a half wave rectifier circuit uses a diode, filter and regulator to change a half wave signal into a constant

Uploaded by

yopyprasetya
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

HALF WAVE RECTIFIER CIRCUIT

TUGAS

Disusun Guna Memenuhi salah satu tugas Mata kuliah Bahasa Inggris Teknik 2

yang dibimbing oleh Bu Yuni Rahmawati

Disusun oleh :

1. AFFIF DARMAWAN ( 207533409572)

2. DIAN ADIANSYAH (207533409579)

3. YOPY PRASETYA ( 207533409584)

JURUSAN ELEKTRO
PRODI S-1 PENDIDIKAN TEKNIK INFORMATIKA
UNIVERSITAS NEGERI MALANG
September 2008

HALF WAVE RECTIFIER CIRCUIT


A. PURPOSE
1. The student can make a rectifier circuit
2. The student can understanding how the rectifier circuit work

B. MATERIAL AND EQUIPMENT


1. Osiloscope FG GOS 620 , FG 20 MH
2. Transformator
3. Diode
4. Analog multimeter
5. Regulator LM 7805
6. Filter 1000 micro farad
7. Jumper wire
8. Project board
9. Resistor ( RL 1 kilo ohm)

C. PROCEDURE
a) Calibrate the Ch 1and Ch2 in oscilloscope
b) Make a a half wave of rectifier circuit (without filter, regulator and RL)
c) Arrange the oscilloscope in 5V/div and 5ms/div, dual mode
d) Use the Ch 1 to measuring the test point 1 and Ch 2 to test point 2
e) Add the filter capacitor 1000 micro farad/16V and RL 1 kilo ohm then
measures TP 1 and TP 2
f) Add regulator LM 7805, output capacitor and RL 1 kilo ohm, use channel 1
and channel 2(AC dual mode). Each one for measuring output ripple filter
voltage in TP 1 and output ripple regulator voltage in TP 2
D. DATA ANALYSIS

Explanation picture 1: In TP 0 (input diode), the


curve showing back and forth AC wave from
transformer.

Explanation picture 2: In TP 1(output diode), the


curve showing DC wave, it means diode already
change AC voltage become DC voltage.

Explanation picture 3: In TP 2(output from filter


), The curve showing like ripple.
Explanation picture 4: In TP 3( output
regulator), The curve showing DC voltage is flat
or Ic = 0

E. CONCLUSION
A half wave of rectifier circuit is consist of 1 diode,filter,RL,and regulator.
The filter utility is to change a half wave signal become DC constant voltage, While
which completing with weaken ripple until DC output voltage become flat or
constant.

You might also like