Scribd
Upload
65 views1 page

Kicktolerance Berekeningen: Kick Zone Parameters

This document contains parameters for calculating kick tolerance for an oil and gas well. It lists technical details such as measured depths, pore pressure and fracture gradients, well geometry, mud weights, and temperature data. It then shows the results of calculations for minimum and maximum pore pressure scenarios, including maximum gas heights and kick tolerances. The parameters are used to model well conditions and determine drilling safety margins.

Uploaded by

HerbertLansink
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
65 views1 page

Kicktolerance Berekeningen: Kick Zone Parameters

This document contains parameters for calculating kick tolerance for an oil and gas well. It lists technical details such as measured depths, pore pressure and fracture gradients, well geometry, mud weights, and temperature data. It then shows the results of calculations for minimum and maximum pore pressure scenarios, including maximum gas heights and kick tolerances. The parameters are used to model well conditions and determine drilling safety margins.

Uploaded by

HerbertLansink
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

Kicktolerance berekeningen

Original sheet Sheet Pore pressure reference 1 2 3 4 5 6 7 8 Kick Zone Parameters: Openhole Size ? Measured Depth ? Vertical Depth (m) ? Horizontal Length (Angle>87 deg) ? Tangent Angle Above Horizontal ? Min Pore Pressure Gradient ? Max Pore Pressure Gradient ? Kick Zone Temperature ? Weak Point Parameters: Measured Depth ? Vertical Depth ? Section Angle (<87 deg) ? Fracture Gradient / EMW ? Weak Point Temperature ? Other Parameters: Bottom Hole Assembly OD ? Bottom Hole Assembly Length ? Drillpipe OD ? Surface Pressure Safety Factor ? Mud Weight in Hole ? Annular Capacity Around BHA: Annular Capacity Around DP: Fracturing Pres at Weak Point: Gas Gradient at Weak Point: Max Allowable Shut-in Csg Pres: Min Pore Pressure at Kick Zone: Gas Gradient at Min Pore Pres: Maximum Allowable Gas Height: Kick Tolerance at Min Pore Pres: Max Pore Pressure at Kick Zone: Gas Gradient at Max Pore Pres: Maximum Allowable Gas Height: Kick Tolerance at Max Pore Pres: (inch) (m) (m) (m) (deg) (sg) (sg) (deg.F) 12.25 2905 2052 0 50 1.03 1.06 177 Swab kick PP= Mudwt 12.25 2905 2052 0 50 1.2 1.2 177 Eigen Sheet Uitgaan van 100 bbl kick SFG berekenen 12.25 2025 0 50 Uitgaan van SFG influx berekenen

Assumed T1=T2

9 10 11 12 13 14 15 16 17 18

(m) (m) (deg) (sg) (deg.F) (inch) (m) (inch) (psi) (sg) (bbl/m) (bbl/m) (psi) (sg) (psi) (psi) (sg) (m) (bbl) (psi) (sg) (m) (bbl)

770 678 50 1.4 87 8 150 5.5 100 1.2 0.274 0.382 1349 0.070 93 3003 0.124 366 122 3091 0.127 312 101

770 678 50 1.4 87 8 150 5.5 100 1.2 0.274 0.382 1349 0.070 93 3499 0.142 58 17 3499 0.142 58 17

670 1.72 Assumed T1=T2 1.4

5 0

100

31

100

31

You might also like