Scribd
Upload
68 views6 pages

How To Configure DH+ Between Panelview Plus and Slc504 Using 2711P-Rn6

This document provides instructions for configuring DH+ communication between a PanelView Plus terminal and an Allen-Bradley SLC504 PLC without using a 1784-PKTX or PCMK card. It involves creating an RSLogix500 application on the PC to communicate to the PLC over DH+, then creating an RSView ME application to configure the DH+ network connection from the PanelView Plus to the PLC.

Uploaded by

for_c
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
68 views6 pages

How To Configure DH+ Between Panelview Plus and Slc504 Using 2711P-Rn6

This document provides instructions for configuring DH+ communication between a PanelView Plus terminal and an Allen-Bradley SLC504 PLC without using a 1784-PKTX or PCMK card. It involves creating an RSLogix500 application on the PC to communicate to the PLC over DH+, then creating an RSView ME application to configure the DH+ network connection from the PanelView Plus to the PLC.

Uploaded by

for_c
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

How to configure DH+ between PanelView Plus and SLC504 using 2711P-RN6

If you dont have 1784-PKTX card or PCMK card, you are still able to configure PanelView Plus talking to SLC504 thru DH+ network. Here is the example.

1.Create a RSLogix500 application the processor - Link SLC504 to your PC using AB_DF1-1 - Create a RSLogix500 application, we will just use N7:0 address. Download the application to the processor. - Leave SLC504 in running. Go to RSLinx and delete AB_DF1-1 2.Create a RSView ME application - Link PC to SLC504 using RS232 cross-over cable - Launch RSView ME > Double click Communication Setup > Create a new configuration. - Under Local tab, add DF1 driver and configure it as following screens

- Create a shortcut and point to the SLC504 under DF1 driver

Create a new display, put a numeric display and a numeric input objects on it. Make sure to connect N7:0. Save the display as Test

- Test the display and make sure you can input and display N7:0 data

- Under Start, do following settings:

- Back Communication setup screen > Target tab > Add driver and choose DH+ (1784-PKTX, 2711-RN6, 2711RN8) > OK

- Driver selection is followed by a dialog that lets you set the drivers Name, the adapters Station ID and Jumper ID, and the network Baud rate:

This same configuration dialog can be modified later, by doing a Right click on the Driver properties.

- Now add the processor beneath that adapter: Right click DHPlus, DH+ > Add device > Choose relevant processor > OK

- Re-point the shortcut name to the processor again. Be sure, this time you define the pointer in Target tab

3. Download application to PanelView Plus - Use a straight thru cable to link PC and PanelView Plus - Under communication setup > Local Tab > Right click DF1 > Properties

- Hit OK and you should be able to see PanelView Plus (a PC icon)

Create a runtime application Use Transfer Utility to download the application to PVP thru DF1 drive

Connect PanelView Plus and SLC504 using DH+ cable When downloading finishes, load the application and run it.

4.Cable connection DH+ 3. Clear 2. Shield 1. Blue PanelView Plus RIO 3. Blue 2. Shield 1. Clear SLC504 DH+ 1. Blue Shield 2. Clear

You might also like