Chapter 7 Heat
Chapter 7 Heat
Chapter 7
FORM 1 CHAPTER 7
HEAT
Ice
X : …………………..…..
Steam
Process Z
Y : …………………..…..
Diagram 1.1
(a) Name processes X and Y in Diagram 1.1 using the following words
[2 marks]
(b) Diagram 1.2 shows the drying of clothes under the sun.
Diagram 1.2
……………………………………………………………………………………………………
[1 mark]
(ii) Draw the changes in the arrangement of particles during this process.
[2 marks]
…………………………………………………………………………………………………….
[1 mark]
2. Diagram 2.1 shows an activity involving different ways of heat flow from a fire.
Y : …………………………….
X : ………………………………
Z : …………………………
Diagram 2.1
(a) State the ways of heat flow in Diagram 2.1 using the following information.
[2 marks]
(b) Draw the direction of heat flow from the hot pot to the hand in the box provided in
Diagram 2.2
Diagram 2.2
[1 mark]
(c) Diagram 2.3 shows an electric kettle that functions using the principle of heat transfer.
Diagram 2.3
……….………………………………………………………………………………………….
[1 mark]
(ii) Draw arrows to show the convection current that occur in the kettle in the box in
Diagram 2.3.
[1 mark]
3. Diagram 3.1 shows an activity that is carried out to study the effect of heating on a metal
ball.
ring
ring
metal ball
metal ball
Diagram 3.1
(a) What can be observed when the heated metal ball is placed on the ring?
…………………………………………………………………………………………………
[1 mark]
………………………………………………………………………………………………………….
[1 mark]
(c) What happens to the particles in the metal ball when the metal ball is heated?
……………………………………………………………………………………
…. ………
[1 mark]
(d) Draw the changes in arrangement of particles when the metal ball is heated.
[1 mark]
(e) Diagram 3.2 shows the effect of heat on the bimetallic strip
Metal P
Metal Q
Before heating After heating
Diagram 3.2
………………………………………………………………………………….…………..
………………………………………………………………………………………………
[1 mark]
(ii) Diagram 3.3 shows bimetallic strip used in a fire alarm. Label P and Q in the boxes
provided so that fire alarm system can function.
Contact point
Emergency
light
Contact screw
Fire alarm
rings
Power supply
Diagram 3.3
(iii) What causes the alarm to ring when the bimetallic strip bends?
……………………………………………………………………………………………………..
[1 mark]
4. (a) Diagram 4.1 shows two shirts of different colours which are being dried under the same
conditions.
Black shirt
White shirt
Situation A Situation B
Diagram 4.1
(i) Based on your observations in Figure 8.1, state the difference in the time taken for
the
shirts to dry in Situation A and Situation B.
… …………………………………………………………………………………………………
……………………………………………………………………………………………………
[1 mark]
(ii) What inference can be made based on Situation A and Situation B in Diagram 4.1?
…….. ……………………………………………………………………………………………..
……………………………………………………………………………….. …………………….
[1 mark]
(b) Diagram 4.2 shows an experiment to study the absorption of heat by different surfaces.
The apparatus is being heated for 5 minutes and the thermometer reading in each
minute is recorded in the table 4.3 below. The final thermometer reading is shown.
40
35
Diagram 4.2
0 35 35
1 36 35
2 38 36
3 40 36
4 42 37
Table 4.3
[3 marks]
………….......................................................................................................................
…………..…………………………………………………………………………….. ………
[1 mark]
(iv) Based on the information in Table 4.3, plot a graph to show the relationship between
the time of heating, t and the thermometer reading.
[2 marks]
(v) Based on the graph, what is the relationship between the time, t and the
temperature, T?
………………………………………………………………………………………………….
………………………………………………………………………………………………….
[1 mark]
(vi) Predict what will happen to the thermometer X reading after 5 minutes.
…………………………………………………………………………………………………
…………………………………………………………………………………………………
[1 mark]
5. Diagram 5.1 shows an activity to compare the heat conductivity of three different metal rods,
P, Q and R.
Rod P
Rod Q
Rod R
Wax
Thumbtack
Diagram 5.1
The rods are heated equally at one end. The time taken for the thumbtacks to drop is given
in Table 5.2.
Table 5.2
……………………………………………………………………………………………………….
[1 mark]
……………………………………………………………………………………………………
[1 mark]
………………………………………………………………………………………………….
[1 mark]
……………………………………………………………………………………………………….
[1 mark]
(d) (i) Which of the metals, P, Q, or R is the best material for making a frying pan?
………………………………………………………………………………………………….
[1 mark]
……………………………………………………………………………………………………
…………………………. ……………………………………………………………………….
[1 mark]