Scribd
Upload
38 views2 pages

Project:: Shape Sheet - Linear Element No. 2 Linear

This document summarizes the structural analysis of a linear element with an IPE400 cross section. It describes the element's material properties, cross section dimensions, strength checks for various load cases, and stability checks against buckling and lateral-torsional buckling. All load and resistance factors are below code limits, indicating the design is adequate for the given loads.

Uploaded by

say10u3757
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
38 views2 pages

Project:: Shape Sheet - Linear Element No. 2 Linear

This document summarizes the structural analysis of a linear element with an IPE400 cross section. It describes the element's material properties, cross section dimensions, strength checks for various load cases, and stability checks against buckling and lateral-torsional buckling. All load and resistance factors are below code limits, indicating the design is adequate for the given loads.

Uploaded by

say10u3757
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 2

Project:

Shape sheet - Linear element No. 2 Linear

1) Cross section
Shape
Dimensions(cm)
Cross sections(cm)
Inertia
Modules(cm3)
Material
Grade

IPE400
h = 40.00 b = 18.00 tw = 0.86 tf = 1.35 r = 2.10 r1 = 0.00
Area = 84.46 Avy = 51.15 Avz = 42.69
It = 51.08(cm4) Iy = 23130(cm4) Iz = 1318(cm4) Iw = 492215(cm6)
Wply = 1307 Wplz = 229
S235 E = 210000 MPa Nu = 0.3 G = 80800 MPa
fy = 235.0 MPa fu = 360.0 MPa

2) Section classification
Class

Lower wing : Class 1 Center : Class 1 Upper wing : Class 1


Cross section : Class 1

3) Deflections
1st criterion

Case no 106 : 1x[1 G]+1x[2 Q]


L/1287 < L/500 (39 %)

1st criterion
Max deflect.1st criterion z = 0.58 cm at x = 2.500 m
4) Cross sections strength
Tension
Compression
(6.2.4)
Shear in y direction
(6.2.6)
Shear in z direction
(6.2.6)
Bending /yy
(6.2.5)
Bending /zz
(6.2.5)
Oblique bending
(6.2.9.1)
Torsion
(6.2.7)

Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.5


Fx < Npl : 55.7 < 1984.8 kN (3 %)
Case no -, Mesh No. -,
Fy < Vply: not done (-)
Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.5
Fz < Vplz : 189.7 < 579.2 kN (33 %)
Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.3
MyEd < MyRk : 119.7 < 307.1 kN*m (39 %)
Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.1
MzEd < MzRk : 0.0 < 53.8 kN*m (0 %)
Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.3
Edc Rd < 1 (6.12) : 0.38979 < 1 (39 %)
Case no -, Mesh No. -,
Mx < Wt M0: not done (-)

5) Elements stability
Unfavorable case
Buckling /yy
(6.3.1)
Buckling /zz
(6.3.1)
Lateral-torsional
buckling
(6.3.2.1)

Case no 104 : 1.35x[1 G]+1.5x[2 Q], Mesh No. 2.3 2/4


Lfz = 6.558 m y = 0.422 Curve a y = 0.21 y = 0.61 y = 0.947
Ncry = 11142.0 kN
Lfy = 24.981 m z = 1.348 Curve b z = 0.34 z = 1.60 z = 0.405
Ncrz = 1092.7 kN
Ldi = 5.000 m Lds = 5.000 m
C1 = 2.570 C2 = 1.550 zg = 0.000 m kz = 1.000 kw = 1.000
Mcr = 769.6 kN*m LT = 0.632
Curve b LT = 0.34 LT = 0.77 LT = 0.821

Auxiliary terms

Cmy0 = 1.00 Cmz0 = 0.78 NcrT = 2835.0 kN

Report No.:

166326995

Page 1

Project:
(Annex A)

Interaction
coefficients
(Annex A)
Vrification
(6.61)
Vrification
(6.62)

Report No.:

max = 1.35 0 = 1.01 0limite = 0.31


Cmy = 1.00 Cmz = 0.78 CmLT = 1.03
muy = 1.00 muz = 0.97 wy = 1.13 wz = 1.50 npl = 0.03
bLT = 0.00 cLT = 0.59 dLT = 0.00 eLT = 0.24
Cyy = 0.99 Cyz = 0.71 Czy = 0.96 Czz = 1.00
kyy = 1.05 kyz = 0.81 kzy = 0.55 kzz = 0.80

+ kyy y Edy RdLTy RkM1 + kyz z Edz Rdz RkM1 1.00


0.03 + 0.50 + 0.00 = 0.53 < 1.00 (53%)
EdzRkM1 + kzy y Edy RdLTy RkM1 + kzz z Edz Rdz RkM1 1.00
0.07 + 0.26 + 0.00 = 0.33 < 1.00 (33%)
EdyRkM1

166326995

Page 2

You might also like