Scribd
Upload
46 views

Product Specification: PDC284-CAMR21-BW

This document provides product specifications for a common anode, deep red, .28" 7mm quad digit display with part number PDC284-CAMR21-BW. Key details include that it uses an AlInGaP chip, has a deep red emitting color, and common anode configuration. It lists electrical and optical characteristics like forward voltage, luminous intensity, peak wavelength, and reverse current parameters. Mounting and soldering recommendations are also provided along with packaging specifications.

Uploaded by

api-62031994
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
46 views

Product Specification: PDC284-CAMR21-BW

This document provides product specifications for a common anode, deep red, .28" 7mm quad digit display with part number PDC284-CAMR21-BW. Key details include that it uses an AlInGaP chip, has a deep red emitting color, and common anode configuration. It lists electrical and optical characteristics like forward voltage, luminous intensity, peak wavelength, and reverse current parameters. Mounting and soldering recommendations are also provided along with packaging specifications.

Uploaded by

api-62031994
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

PRODUCT SPECIFICATION

Part Number

PDC284-CAMR21-BW
Details .28 (7.00mm) Quad Digit Display Common Anode Emitting Color: Deep Red AlInGaP chip used

Features Qualified according to JEDEC moisture sensitivity level 2A RoHS Compliant Black Face, White Segment Easy mounting on PCB

Mechanical Dimensions

Notes: 1. Dimension in millimeter [inch], and tolerance is 0.25 [.010] unless otherwise noted. 2. BendingLength*1%.

www.ptec.net

071513Rev0MS

Page1of6

Device Selection Guide Model Number PDC284-CAMR21-BW Material AlInGaP Chip Emitting Color Deep Red Description Common Anode

Absolute Maximum Ratings at Ta=25 Deep Red Parameter Power Dissipation per Dice Derating Liner from 25 per Dice Continuous Forward Current Per Dice Peak Current Per Dice (duty cycle 1/10, 1KHz) Reverse Voltage Per Dice Operating Temperature Storage Temperature Symbol PAD -IAF IPF VR Topr Tstg Rating 70 0.33 25 90 5 -35~+85 -35~+85 Unit mW mA/ mA mA V

Note: Solder Conditions: 1/16 inch below seating plane for 3 seconds at 260 . Or temperature of unit (during assembly) not over max temperature rating above

Electrical and Optical Characteristics at Ta=25 Deep Red Parameter Forward Voltage Per Segment Luminous Intensity Per Segment Peak Emission Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Reverse Current Luminous Intensity Matching Ratio Symbol VF Iv P Ld IR Iv-m Min. -1.6 -----Typ. 2 3,5 660 645 20 --Max. 2.8 Unit V mcd nm nm nm A -Condition IF=20mA IF=10mA IF=20mA IF=20mA IF=20mA VR=5V IF=10mA

100 2:1

www.ptec.net

071513Rev0MS

Page2of6

All Light On Segments Feature & Pad Position

Internal Circuit Diagram

www.ptec.net

071513Rev0MS

Page3of6

Typical Electrical / Optical Characteristic Curves Deep Red

www.ptec.net

071513Rev0MS

Page4of6

Recommended Soldering 1. Wave Soldering a. Basic SPEC. is 5sec. When 260 . If temperature is higher, time should be shorter (+10 -1sec.). b. Power dissipation of iron should be smaller than 15W, and temperature should be controllable. Soldering temperature should be under 260 , time 3sec

www.ptec.net

071513Rev0MS

Page5of6

Packing and Label Specifications

Note: 1. Specifications subject to change without notice.

www.ptec.net

071513Rev0MS

Page6of6

You might also like