Mechanical Seal Piping Plans Companion Booklet
Single Seals Dual Seals Quench Seals Second. Cont. Dual Gas
Introduction
A primary factor in achieving highly reliable, effective sealing performance is to create the best fluid environment around the seal. Selection of the right piping plan and associated fluid control equipment requires a knowledge and understanding of the seal design and arrangement, fluids in which they operate, and of the rotating equipment. Providing clean, cool face lubrication, effective heat removal, personnel and environmental safety, leakage management and controlling system costs are among the specific factors that must be considered. API has established standardized piping plans for seals that provide industry guidelines for various seal arrangements, fluids and control equipment. The following pages illustrate and describe features of these plans as an aid to help you determine what support system requirements will maximize the performance reliability of your fluid handling rotating equipment application.
API 682/ISO 21049 standards have default (required) connections and connection symbols for seal chamber and gland plate connections based upon the seal configuration. It is recommended that the latest edition of these standards be reviewed for up-to-date requirements, when these standards are mandated for a piece of rotating equipment. The intent of this booklet is to illustrate the common connections that are utilized for the various piping plans, regardless of the equipment type, and therefore use
generic names for connections. The end user and/or equipment manufacturer may have specific requirements that dictate what connections are to be supplied and how they are to be labeled. In the piping plans illustrated, the Flush connection noted for the inboard seal of a dual seal may originate from a number of suitable sources. For example, the Flush for piping plans 11/75 or 32/75 may be the product (Plan 11) or an external source (Plan 32).
API682/ISO21049 General Comments
Piping Plan Description
Plan 01 Single Seals - Internal Flush Plan 02 Single Seals - No Flush, Large Open Bore Plan 11 Single Seals - By-Pass From Discharge With Orifice Plan 12 Single Seals - By-Pass From Discharge With Filter & Orifice Plan 13 Single Seals - Flush Thru Seal Chamber Thru Orifice To Suction Plan 14 Single Seals - By-Pass From Discharge Thru Seal Chamber Back To Suction Plan 21 Single Seals - By-Pass From Discharge Thru Orifice & Heat Exchanger Plan 23 Single Seals - Closed Loop Circulation Thru Heat Exchanger Plan 31 Single Seals - By-Pass From Discharge Thru Orifice & Abrasive Separator Plan 32 Single Seals - External Flush Source To Seal Plan 41 Single Seals - By-Pass From Discharge Thru Abrasive Separator & Heat Exchanger Plan 52 Dual Seals, Unpressurized - External Reservoir Unpressurized Liquid Buffer
Plan 53A Dual Seals, Pressurized - External Reservoir Pressurized Liquid Barrier Plan 53B Dual Seals, Pressurized - Liquid Barrier Thru Heat Exchanger & Pressurized By Accumulator Plan 53C Dual Seals, Pressurized - Liquid Barrier Thru Heat Exchanger With Differential Tracking .... Piston Accumulator Plan 54 Dual Seals, Pressurized - External Pressurized Barrier System/Source Plan 62 Quench Seals - External Quench On Atmospheric Side Of Seal Plan 65 Single Seals - External Leakage Detection Reservoir Plan 72 Secondary Containment Seals - Low Pressure Buffer Gas Injected To Outer Seal Cavity Plan 74 Dual Gas Seals - Pressurized Dual Gas Seal Thru Conditioning Panel Plan 75 Secondary Containment Seals - Secondary Cont. Seal With Leakage Collection Reservoir Plan 76 Secondary Containment Seals - Secondary Cont. Seal Vented To Flare Or Collection System
Piping Plan Description
Plan 01 Single Seals
Description: Plan 01 is an internal recirculation from the pump discharge area of the pump into the seal chamber, similar to a Plan 11 but with no exposed piping.
General: This flush plan should only be used for clean products as dirty products can clog the internal line. Not recommended on vertical pumps.
Advantages: No product contamination
and no external piping. Advantageous on highly viscous fluids at lower temperatures to minimize the risk of freezing that can occur with exposed piping arrangements.
Vent Plugged
Internal Flush Porting Vent Plugged Drain Drain Gland End View
Gland End View Vent (If Reqd.) Plugged No External Flush C Quench Optional
C C
Plan 01 Single Seals
Plan 02 Single Seals
Description: Plan 02 is a non-circulating flush plan recommended only where adequate vapor suppression can be assured.
General: Ideal with large bore/tapered
bore ANSI/ASME B73.1 or ISO 3069 Type C seal chambers or with hot process pumps utilizing a cooling jacket. On the latter services, a Plan 62 with steam quench can also provide some additional cooling.
Advantages: Solids are not continually
introduced into the seal chamber, no external hardware is required, and natural venting occurs when used with a tapered bore seal chamber.
Heating/Cooling Inlet/Outlet Large Bore Open Throat Or Taper Bore Box Is Recommended Vent Plugged Drain
Vent Plugged
Drain Gland End View
Gland End View
No Flush Vent (If Reqd.) Plugged C Quench Optional C Ensure Seal Chamber Is Fully Vented
C C
Plan 02 Single Seals
Plan 11 Single Seals
Description: Plan 11 is the most common flush plan in use today. This plan takes fluid from the pump discharge (or from an intermediate stage) through an orifice(s) and directs it to the seal chamber to provide cooling and lubrication to the seal faces.
Advantages: No product contamination
and piping is simple.
General: If the seal is setup with a distributed or extended flush, the effectiveness of the system will be improved.
Orifice By-Pass From Discharge
Flush
Flush Drain
Drain Gland End View
Gland End View
Quench Optional
Plan 11 Single Seals
Plan 12 Single Seals
Description: Plan 12 is similar to Plan
11, except that a strainer or filter is added to the flush line.
General: If the seal is setup with a distributed or extended flush, the effectiveness of the system will be improved. This plan should be equipped with a differential pressure indicator or alarm to alert the user that the filter or strainer is clogged.
Advantages: No product contamination
and solids are removed from the flush stream keeping the seal clean.
Strainer Or Filter By-Pass From Discharge Orifice Cleanout Trap Flush Drain
Flush
Drain Gland End View
Gland End View
Quench Optional
Plan 12 Single Seals
Plan 13 Single Seals
Description: In a Plan 13, the flow exits
the seal chamber through an orifice and is routed back to pump suction.
General: Typically Plan 13 is used on
vertical turbine pumps since they have the discharge at the top of the pump where the seal is located. Because of the difference in flow patterns, Plan 13 is not as efficient in removing heat as a Plan 11 and thus requires a higher flow rate.
Advantages: With a Plan 13, it is possible to increase or decrease seal chamber pressure with proper sizing of the orifice and throat bushing clearance.
Orifice
Flush Outlet
Return To Suction
Flush Outlet Drain
Drain Gland End View
Gland End View
Quench Optional
Plan 13 Single Seals
Plan 14 Single Seals
Description: Plan 14 is a combination
of Plans 11 and 13. Flush is taken off of pump discharge, sent to the seal chamber, and piped back to pump suction.
General: Often used on vertical pumps o provide adequate flow and vapor t pressure margin independent of throat bushing design.
Advantages: Cooling can be optimized
with the flush directed at the seal faces. Plan allows for automatic venting of the seal chamber.
By-Pass From Discharge
Orifice
Flush Outlet
Orifice Return To Suction Flush Inlet (Alt. into Gland) Gland End View Flush Outlet Drain Drain Flush Inlet Gland End View
Quench Optional
Plan 14 Single Seals
Plan 21 Single Seals
Description: Plan 21 is a cooled version of Plan 11. The product from pump discharge is directed through an orifice, then to a heat exchanger to lower the temperature before being introduced into the seal chamber. and reduces the possibility of vaporization in the seal chamber.
General: Plan 21 is not a preferred plan,
either by API or many users, due to the high heat load put on the heat exchanger. A Plan 23 is preferred.
Advantages: Process fluid cools and
lubricates the seal, therefore no dilution of process stream. Cooling improves lubricity
Orifice
Vent, Normally Closed
Heat Exchanger Vent, Normally Closed
By-Pass From Discharge
Cooling Water Connections
Flush Drain, Norm. Closed
Flush
Temperature Indicator Drain Drain Gland End View
C
Gland End View
Quench Optional
Plan 21 Single Seals
Plan 23 Single Seals
Description: Plan 23 is a closed loop
system using a pumping ring to circulate product through a heat exchanger and back to the seal chamber.
General: Preferred plan for hot applications. Close clearance throat bushing is recommended to reduce mixing of hot product with cooler closed loop system fluid.
Advantages: More efficient than a Plan
21 and less chance of heat exchanger fouling. Reduced temperature improves lubricity and improves vapor pressure margin.
Vent, Normally Closed
Heat Exchanger Cooling Water Vent, Normally Closed
Flush Outlet (Alt. from Gland Conn.)
Cooling Water Connections
Flush Outlet Shown For CW Shaft Rotation
Flush Inlet Pumping Ring
Cooling Water Drain, Norm. Closed Temperature Indicator Drain Gland End View Drain Quench Optional Flush Inlet
Gland End View
C
Plan 23 Single Seals
Plan 31 Single Seals
Description: Plan 31 is a variation of
Plan 11, where an abrasive separator is added to the flush line. In this plan, the product is introduced to the abrasive separator from the discharge of the pump, clean flush is piped from the separator to the seal chamber and solids are returned to the pump suction. flush stream keeping the seal clean.
General: This plan should be used for
services containing solids that have a specific gravity at least twice that of the process fluid. Typically the separator requires a minimum pressure differential of 15 psi to operate properly. Note: A abrasive separator is subject to wear and must be maintained regularly to ensure efficient operation.
Advantages: Unlike a strainer or filter,
the abrasive separator does not require cleaning. Solids are removed from the
Flush By-Pass From Discharge
Abrasive/ Cyclone Separator Orifice (optional) Flush
Return To Suction
Drain Gland End View
Drain
Gland End View
Quench Optional
Plan 31 Single Seals
Plan 32 Single Seals
Description: Plan 32 uses a flush
stream brought in from an external source to the seal. This plan is almost always used in conjunction with a close clearance throat bushing.
General: When an outside flush source
is used, concerns regarding product dilution and/or economics must be considered by the user. Source pressure must be maintained a minimum of 15 psig above maximum seal chamber pressure.
Advantages: The external flush fluid,
when selected properly, can result in vastly extended seal life.
Flow Control Valve Pressure Indicator
Flow Indicator (Optional) Valve, Normally Open Strainer/Filter Clean/Compatible External Flush Source Flush
Flush
Clean Out Trap Temperature Indicator (Optional) Close Clearance Bushing Drain Gland End View
Check Valve
Drain Gland End View
C
Quench Optional
Plan 32 Single Seals
Plan 41 Single Seals
Description: Plan 41 is a combination of
Plan 21 and Plan 31. In Plan 41, product from pump discharge is first put through an abrasive separator and then to the heat exchanger before being introduced to the seal chamber.
General: Plan 41 is typically used on hot
services with solids; however, depending on the temperature of the process, oper ating costs can be high. This plan should be used for services containing solids that have a specific gravity at least twice that of the process fluid. Typically the separator requires a minimum pressure differential of 15 psi to operate properly.
Advantages: Solids are removed and
product temperature is reduced to enhance the seals environment.
Abrasive/Cyclone Separator
Heat Exchanger
Vent, Normally Closed
By-Pass From Discharge Return To Suction Flush
Cooling Water Connections
Drain, Norm. Closed Temperature Indicator Drain
Flush
Drain Gland End View Gland End View
C
Quench Optional
Plan 41 Single Seals
Plan 52 Dual Seals, Unpressurized
Description: Plan 52 uses an external
reservoir to provide buffer fluid for the outer seal of an unpressurized dual seal arrangement. Advantages: In comparison to single seals, dual unpressurized seals can provide reduced net leakage rates as well as redundancy in the event of a primary seal failure.
General: Cooling coils in the reservoir re available for removing heat from the a buffer fluid. Plan 52 is often used where process fluid contamination can not be tolerated.
Note: Tangential porting is unidirectional. Gland is illustrated for CCW shaft rotation from drive end.
Vent, Normally Open Orifice Check Valve
To Collection System Pressure Switch (High) Pressure Indicator Sight Level Gauge Reservoir Cooling Coils Buffer Outlet Flush
Make-Up Buffer Liquid, Normally Closed Level Switch (Low) Buffer Inlet Buffer Outlet Primary Seal Flush (if reqd.) Pumping Ring Cooling Water Out Gland End View
Cooling Water In Buffer Inlet Gland End View
Buffer Liquid Drain, Normally Closed
Plan 52 Dual Seals, Unpressurized
Plan 53A Dual Seals, Pressurized
Description: Plan 53A uses an external
reservoir to provide barrier fluid for a pressurized dual seal arrangement. Reservoir pressure is produced by a gas, usually nitrogen. Flow is induced by a pumping ring.
General: Heat is dissipated by reservoir
cooling coils. Barrier fluid is subject to gas entrainment at pressures/temperatures above 300 psi/2500F.
Advantages: Reservoir size can be
optimized dependent on flow rate. Wear particles settle to bottom of reservoir and dont get recirculated.
Note: Tangential porting is unidirectional. Gland is illustrated for CCW shaft rotation from drive end.
Pressure Source, Normally Open Check Valve Pressure Switch (Low) Pressure Indicator Sight Level Gauge Pressure Reservoir Cooling Coils Barrier Outlet
Make-Up Barrier Liquid Fill, Normally Closed
Level Switch (Low) Barrier Inlet Barrier Outlet Flush (when specified) Cooling Water Out Gland End View Pumping Ring
Cooling Water In Barrier Inlet Gland End View
Barrier Liquid Drain, Normally Closed
Plan 53A Dual Seals, Pressurized
Plan 53B Dual Seals, Pressurized
Description: Plan 53B, previously
termed 53 Modified, uses an accumulator to isolate the pressurizing gas from the barrier fluid. A heat exchanger is included in the circulation loop to cool the barrier fluid. Flow is induced by a pumping ring. The make-up system can supply barrier fluid to multiple dual pressurized sealing systems.
General: The bladder accumulator isolates the pressurizing gas from the barrier fluid to prevent gas entrainment. The heat exchanger can be a water-cooled unit, an air-cooled unit, or utilize finned tubing based upon the system heat load.
Advantages: Should the loop be contaminated for any reason, the contamination is contained within the closed circuit.
Note: Tangential porting is unidirectional. Gland is illustrated for CCW shaft rotation from drive end.
Vent, Normally Closed
Cooling Water Connections Pressure Switch (Low) Pressure Indicator Valve, Normally Open
Barrier Outlet
Valve, Normally Open Barrier Outlet Flush (when specified) Barrier Inlet Heat Exch. Gland End View Drain, Normally Closed
Barrier Inlet Gland End View Bladder Charge Connection Accumulator
Pumping Ring
Barrier Liquid Fill, Normally Closed
Plan 53B Dual Seals, Pressurized
Plan 53C Dual Seals, Pressurized
Description: Plan 53C uses a piston
accumulator to provide pressure to the system. It uses a reference line from the seal chamber to provide a constant pressure differential over the chambers pressure. A water- or air-cooled heat exchanger provides for barrier fluid cooling. Flow is induced by a pumping ring.
Advantages: Provides a tracking system
to maintain barrier pressure above seal chamber pressure.
General: The heat exchanger can be a
water-cooled unit, an air-cooled unit, or utilize finned tubing based upon the system heat load. The reference line to the accumulator must be tolerant of process contamination without plugging.
Barrier Fluid Make-Up Level Indicator Piston Accumulator
Seal Chamber Pressure Ref. Line (Alt. In Seal Chamber)
Temperature Indicator Pressure Indicator
Note: Tangential porting is uni-directional. Gland is illustrated for CCW shaft rotation from drive end.
Pressure Switch (Low) Barrier Outlet Barrier Inlet Gland End View Valve, Normally Open Cooling Water Connections Heat Exchanger Drain, Normally Closed
Seal Chamber Pressure Reference Line
Barrier Outlet
Pumping Ring
Barrier Inlet Gland End View
Plan 53C Dual Seals, Pressurized
Plan 54 Dual Seals, Pressurized
Description: Plan 54 utilizes an external
source to provide a clean pressurized barrier fluid to a dual seal.
General: Plan 54 systems can be custom
engineered to suit application or specific plant requirements. Systems can range from the direct connection from other process streams to complex lubrication systems.
Advantages: Can provide pressurized
flow to multiple seal installations to reduce costs. Positively eliminates fugitive emissions to atmosphere.
Flush (when specified)
Barrier Outlet
External Pressurized Barrier Source/System Barrier Inlet Gland End View
Barrier Outlet
Barrier Inlet Gland End View
Plan 54 Dual Seals, Pressurized
Plan 62 Quench Seals
Description: Plan 62 is a common plan
to improve the environment on the atmospheric side of single seals by quenching with steam, nitrogen or water.
General: Typical applications include;
steam quenches on hot services to retard coking; nitrogen quenches on cold or cryogenic service to prevent icing; or water quench to prevent crystallization or accumulation of product on the atmospheric side of the seal.
Advantages: Plan 62 is a low cost
alternative to tandem seals. The quench prevents or retards product crystallization or coking. Quenches can also provide some cooling.
Steam Quench Illustrated
Steam Trap Used On Steam Quench
Check Valve
Quench Source Valve, Normally Open
Pressure Indicator Valve, Normally Open Quench Inlet Flush (when specified) Drain Outlet Quench Gland End View Close Clearance Bushing Drain Gland End View Flush
Steam Deflector
Plan 62 Quench Seals
Plan 65 Single Seals
Description: Plan 65 is a liquid leakage
detection plan normally used for single seals. It utilizes a level switch on a reservoir to set off an alarm when excess leakage is detected.
General: The system includes a loop to
by-pass the orifice to prevent high pressure on the atmospheric side of the seal. The gland throttle bushing design should be consistent with the fluids properties. Gland throttle bushing designs can vary from fixed designs to segmented bushings.
Advantages: Provides an alarmed indication of excessive seal leakage that can shutdown equipment if necessary.
Throttle Bushing
Gland End View
By-Pass Line
Flush (when specified) Drain Leakage Reservoir Valve, Normally Open Orifice Drain, Normally Open
Level Switch (High) Flush
To Liquid Collection System
Drain Gland End View
Plan 65 Single Seals
Plan 72 Secondary Containment Seals
Description: Plan 72 for secondary
containment uses an external low pressure buffer gas, usually nitrogen, regulated by a control panel that injects it into the outer seal cavity.
General: Plan 72 is normally used with
Plan 75 for primary seal leakage that is condensing, or with Plan 76 for non-condensing leakage.
Advantages: Introduction of a buffer gas
like nitrogen reduces fugitive emissions, prevents icing on cold applications, and provides for some cooling to the outboard seal.
A: Leakage management piping depending upon process fluid properties.
System Components
4 6 2 3 9 7 5 1 2 3 4 5 6 7 8 9
Gas Buffer Supply Inlet VentA Drain A
Shut Off Valve, Norm. Open Coalescing Filter Pressure Regulator Pressure Indicator Pressure Switch Flow Indicator Check Valve Shut Off Valve, Norm. Open Orifice
Flush (when specified)
Gas Buffer Supply Outlet To Seal Gas Buffer Inlet Gland End View
VentA
Flush Gas Buffer Inlet
DrainA Gland End View
Plan 72 Secondary Containment Seals
Plan 74 Dual Gas Seals
Description: Plan 74 provides a pressurized gas, typically nitrogen, to dual gas seals through the use of a control panel that removes moisture, filters the gas, and regulates the barrier pressure.
General: The barrier gas is usually a
pressurized nitrogen line. For higher pressure applications the system pressure can be supplemented with a gas pressure booster/amplifier. Typically dry-running, non-contacting, gas lubricated seals are used with this plan.
Advantages: Lower costs and maintenance than systems used on dual pressurized liquid systems. Leakage to atmosphere is an inert gas.
System Components
1 2 3 4 5 6 7 8
3 5 2 4 1 7 8
Shut Off Valve, Norm. Open Coalescing Filter Pressure Indicator Pressure Regulator Flow Indicator Pressure Switch Check Valve Shut Off Valve, Norm. Open
Gas Barrier Supply Source Inlet Gas Barrier Inlet
Gas Barrier Supply Outlet To Seal
Gas Barrier Inlet
Gland End View Gland End View
Plan 74 Dual Gas Seals
Plan 75 Secondary Containment Seals
Description: Plan 75 is a collection
system used with secondary containment seals for process fluid that will condense at lower temperatures or is always in a liquid state.
General: Plan 75 can be used in conjunction with a gas purge from Plan 72. Typically dry-running, contacting secondary containment seals are used with this plan.
Advantages: The collection reservoir
contains a pressure gauge and a high pressure switch to indicate a build up in pressure from excessive primary seal leakage or failure.
To Vapor Collection System
Orifice Pressure Indicator Pressure Switch (High)
Flush When Specified
Gland End View Drain, Norm. Open
Isolation Valve
Vent Plugged
Flush
Drain Valve Normally Closed
Level Indicator Leakage Collection Reservoir Level Switch (High)
Drain Gland End View
Plan 75 Secondary Containment Seals
Plan 76 Secondary Containment Seals
Description: Plan 76 is a system to divert non-condensing primary seal leakage to a flare or vapor recovery system.
General: Plan 76 can be used in conjunction with a gas purge from Plan 72. Can be used with dry-running, contacting or non-contacting secondary containment seals.
Advantages: Lower initial and maintenance costs than dual unpressurized seals using a Plan 52.
Normally Open Pressure Indicator Pressure Switch (High)
To Flare Or Vapor Recovery System
Orifice
Vent Flush (when specified) Vent To Drain, Norm. Closed Gland End View Normally Closed
Flush
Drain Plugged Gland End View
Plan 76 Secondary Containment Seals
Best Piping Practices
h Minimize piping line losses. h Minimum 1/2 piping or 5/8 tubing. h Use large radius bends. h Tangential outlet ports. h Verify shaft rotation direction. h Slope horizontal runs upward. h Install drain at lowest piping point. h Flush is recommended whenever possible. h Use forced circulation where possible. h Cooling is recommended for buffer/ barrier fluid. h Always properly vent the system prior to start-up. h Always verify pressure and/or level switch set points. h Check system for leaks. h Contact John Crane for buffer/barrier fluid recommendation.
* 18"-24" Normal Conditions 3'-5' If Hot Stand-By Promotes Thermosyphon Effect 1/4 per foot Min. Slope Flush Inlet Shaft Gland Vertical Equipment Flush Outlet To Heat Exchanger 3-5 *
High Point Vent Normally Open
3-5 *
CW Shaft Rot. Shown Horizontal Equipment
Flush Inlet To Seal Low Point Drain Valve
3 Max.
Best Piping Practices Single Seals - Plan 23 Illustrated
Best Piping Practices Dual Seals - Plan 53A Illustrated
3 Max. Horizontal Equipment Barrier Outlet 12 - 30 CW Shaft Rot. Shown Barrier Inlet Drain Valve Low Point Drain Valve 12 - 30 1/4 per foot Min. Slope Vertical Equipment Shaft Gland Barrier Inlet
John Crane offers a full range of standard and custom engineered Lemco brand seal support systems. All systems are designed and built to industry standards including ANSI B31.3 for piping; API 610, 682 and 614 for system design; IEC, NEMA, NEC, or CSA for instrumentation and electrical; and pressure vessels in accordance with ASME requirements. John Crane, Lemco Products Tulsa, Oklahoma, USA tel: 1-918-835-7325 fax: 1-918-835-5823
Lemco Seal Support Systems
Lemco Seal Support
API 682/ISO 21049 Products API 682 Plans 52 and 53A Reservoirs: These reservoirs are designed for the Refinery, Petrochemical, and Chemical Industries. API 682 Plan 53B: A dual pressurized system that eliminates direct gas contact with the barrier liquid. API 682 Plan 53C: This system is ideal for applications that have fluctuating pressures. API 682 Plan 72 Gas Control Panel: Used in a dual unpressurized seal arrangement where the secondary seal is dry-running. API 682 Plan 75 Condensate Collection Reservoir: Used in a dual unpressurized seal arrangement where the secondary seal is dryrunning. API 682 Plan 76 Vent to Flare Panel: Used in a dual unpressurized seal arrangement where the secondary seal is dry-running. API 682 Plan 74 Gas Control Panel: Used on non-contacting, dual pressurized seals, this system filters, regulates and monitors the gas supply, typically nitrogen, used to lubricate the seals.
API 682 Plan 52/53A Reservoirs
API 682 Plan 53B Reservoirs
API 682 Plan53C Reservoir
API 682 Plan 72/74 Gas Control Panel
Lemco Seal Support Systems
Lemco Seal Support Systems
Compressor Gas Panels and Seal Oil Systems
Type 28 Gas Panel
Gas Conditioning Unit
Seal Oil System with AirCooled Heat Exchanger
Heat Exchangers and Auxiliary Equipment
Water-Cooled Heat Exchanger
Air-Cooled Heat Exchanger
Leakage Detection Systems
Abrasive Separators
Lemco Seal Support Systems
Lemco Seal Support Systems
Non-API Reservoirs and Mobile Refill Carts
RE-1203/RE-1205
RE-1603
RE-1518
RE-1618
50 Gallon
ORIFICE BLOCK VALVE CHECK VALVE FLOW REGULATING VALVE PRESSURE CONTROL VALVE CYCLONE SEPARATOR
FILTER/STRAINER HEAT EXCHANGER
PI
COALESCING FILTER
PSH
PRESSURE SWITCH HIGH PRESSURE SWITCH LOW LEVEL INDICATOR
PSL
RESERVOIR
PRESSURE INDICATOR TEMPERATURE INDICATOR FLOW INDICATOR
LI
TI
LSH LEVEL SWITCH HIGH
PISTON ACCUMULATOR
FI
LSL LEVEL SWITCH LOW
BLADDER ACCUMULATOR
FM FLOW METER
FSH FLOW SWITCH HIGH
Instrumentation References
User Notes:
Europe Latin America Slough, UK Sao Paulo, Brazil Tel: 44-1753-224000 Tel: 55-11-3371-2500 Fax: 44-1753-224224 Fax: 55-11-3371-2599
Middle East, Africa, Asia Dubai, United Arab Emirates Tel: 971-4-3438940 Fax: 971-4-3438970
North America Morton Grove, Illinois USA 1-800-SEALING Tel: 1-847-967-2400 Fax: 1-847-967-3915
For your nearest John Crane facility, please contact one of the locations above. If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be contacted prior to their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. 2006 John Crane Inc. Print 9/06 ISO 9001, ISO 14001, ISO/TS 16949 Certified www.johncrane.com MSPP Booklet
