Injection Molding Design Guide
Injection Molding Design Guide
Table of Contents
Injection Mold Tooling Process Comparison...........................................................2 Size Limitations..........................................................................................................3 Straight Pull Design ...................................................................................................4 Other Geometric Considerations ..............................................................................5
Gating .........................................................................................................................7 Resin Selection ..........................................................................................................8 Surface Finish Selection............................................................................................9 Lead Time .................................................................................................................10
Parting Line Limitations ............................................................................................................ 5 Deep Ribs................................................................................................................................. 5 Rounded Corners ..................................................................................................................... 5 Rib-to-Wall Thickness Ratios ................................................................................................... 6 Warp ......................................................................................................................................... 7 Sufficient Draft .......................................................................................................................... 7
Part Material
Part Volume Parting Line Geometry Draft Tolerance Expectations Surface Finish Customer Owns Tool? Method of Tool Manufacture
No volume limit No limit Draft required in CAD model Tighter tolerances are possible Any finish, including acid-etched finish Yes No manufacturing limits, aluminum tooling
No volume limit No limit Draft required in CAD model Tighter tolerances are possible Any finish, including acid-etched finish Yes No manufacturing limits, tooling per customer specs
No limit Draft required in CAD model +/- 0.005, or per SPE standards for material Choose from 6 standard finishes No CNC-only manufacturing, aluminum-only
Lead Time
Standard: 10 Days for 10"x10"x3", 20 Days for 20"x20"x3" Expedited: 5 days, depending upon your geometry
Size Limitations
Size Limits for Rapid Injection Molding
The XY dimensions must be less than 20 x 20. Maximum part volume cannot exceed 36 cubic inches. Maximum part depth can be 3, given a parting line that can pass through the middle of the part, or 1.5 if the parting line of the tool must be at one edge of the part. Parts that fall outside of this box can be manufactured, but must be quoted offline by your Tooling Manager.
1.5
3.0
The Depth Limit is 1.5 for parts where the parting line is on the edge of the part, and 3 for parts where the parting line is central to the part.
Undercuts Require Side Action in the Tool Available only in LowVolume and Production Injection Molding
Deep Ribs
The Rapid Injection Molding process uses only high-speed CNC machining centers to mill out the tooling material. No special manufacturing methods, such as EDM (electric discharge machining), wire EDM or grinding are used to manufacture the tools. As a result of the CNC only approach, deep ribs must be designed to accommodate this limitation. Specifically, deep ribs require proper draft (at least 2 degrees per side) and clearance to allow the CNC machine tool to cut the root of the rib cavity. Rule of Thumb: The maximum rib depth is 10 times the width of the rib at its smallest width. CNC cutting tool lengths (and therefore rib depths) are limited by this. The following chart provides a rule of thumb for rib depth with 1 degree per side of draft:
Rib Depth Rib Width 0.5mm 3.5mm 0.75mm 7.5mm 1.0mm 15mm 1.5mm 25mm 2.0mm 36mm
Low-Volume Injection Molding and Production Injection Molding have no restrictions on rib depth.
Rounded Corners
Since Rapid Injection Molding is a CNC-only process, sharp corners on the outside of parts (meaning sharp corners on the inside of the cavity-side of the tool) are not possible.
The following illustrations show a part with sharp corners and a part with rounded corners. If your design has sharp outside corners, the CNC-only process will round off those features to a radius of .030.
It is strongly advised that you ensure your design has rounded corners on every rib-to-wall or wall-to-wall intersection. This design consistency will result in a part with less internal stress reducing the chance of warp, short shots, splay and flash. Sharp Corners If your design requirements are so stringent that sharp corners on the outside of your part are critical to the parts function, only Low-Volume Injection Molding or Production Injection Molding will meet that need. Low-Volume Injection Molding and Production Injection Molding can accomplish the cavity-side sharp corner using EDM machining methods to literally burn the sharp corner into the tool.
In some cases, using a glass-filled material will help avoid sink in geometries when adhering to the rule-of-thumb is impossible.
Warp
The flow of plastic in a tool is a complex phenomenon - sometimes friendly and predictable, other times evil and erratic. After the molten plastic has filled the tool cavity, the plastic solidifies in the mold and freezes in a direction from the outside of the part (near the mold surface) toward the inside. In thick sections of the part, this results in inward pulling stresses (due to the contraction of cooling), causing sink marks in the outer surfaces of the part. Because thinner areas of the part will freeze faster than thicker sections, stresses can build up between thick and thin sections. The result is a phenomenon called warp. Rule-of-Thumb, for warp: Design your parts to maintain consistent wall thickness and avoid thick areas whenever possible.
Sufficient Draft
The existence of draft on vertical surfaces of your part enables the easy removal of your part from the mold. Draft is especially important in Rapid Injection Molding since the molds are straight-pull only (i.e. no side actions) and manufactured using a CNC-only process. The rules-of-thumb governing the amount of draft required (in degrees) will vary with geometry and surface texture requirements. Lets put it this way the more draft, the better. Rules-of-Thumb, for draft: Use at least 1 degree on all "vertical" faces. 2 degrees works very well in most situations. 3 degrees is a minimum for a shutoff (metal sliding on metal). 3 degrees is required for light and medium texture.
Gating
Rapid Injection Molding tooling is created with one of the following types of gates:
Gate vestige will be trimmed to +/-.005. Low-Volume Injection Molding and Production Injection Molding have no restrictions on the type of gate used.
Resin Selection
Selection of the proper material for your molded parts is a critical decision. One must consider the mechanical properties, molding properties and cost of the resin they select for the given application. Application-specific requirements will always drive the need for particular material properties, like tensile strength and elasticity. Successful plastic part design is based on an understanding of process-related issues during manufacturing, such as mold filling, likelihood of flash, part ejection and the potential for warp and sink. The table below lists some commonly used resins, along with their brand names, and a high-level summary of their material properties, moldability characteristics and relative costs. Standard Rapid Injection Molding Resins
Resin Generic Name Acetal Nylon 6/6 Nylon 6/6, glass filled Polypropylene (PP) Polycarbonate (PC) Acrylonitrile Butadiene Styrene (ABS) Polycarbonate / ABS Alloy Polyetherimide (PEI) Polyetherimide, fiber reinforced (PEI) Polybutylene Terephthalate (PBT) Polystyrene Thermoplastic Elastomer Resin Brand Names Delrin Zytel Zytel Marlex, Sumika Lexan Cycolac Cycoloy Ultem Ultem Valox Styron Thermoplastic Polyurethane, Santoprene Strength Medium Medium High Low Medium Med-Low Medium High Very High Medium Med-Low Low Impact Resistance Medium High Medium High High High High Medium Medium High Low High Change to Stiffnes Med-Low Low High Low Med-High Low Medium High High Low Low Low
Notes: This list is not comprehensive, nor is it constant. There are many other resins not listed here. Ask your Tooling Manager for material selections that are currently available. In order to avoid project delays due to material availability, we limit material selection in Rapid Injection Molding to the material we have on hand at the time your quote is created. Your quote worksheet will present you with the currently available materials. When your project requires a specific engineered material, it becomes either a Low-Volume Injection Molding or Production Injection Molding project. Virtually any injection moldable material can be specified in, as we will source the material per your requirements.
If the part will not be visible to the end user, a non-cosmetic finish is acceptable. But many times your design will require a cosmetic surface finish. In these cases of cosmetic finishes, there are two key limitations to be aware of:
Texturing
Since bead blasting is a line-of-sight method, it may not be possible to texture the sides of minimally drafted ribs on a part, as the mold surfaces may be inaccessible. Also, texturing has an adverse effect on the ability of the part to release from the mold. Drag marks may result. Therefore, we recommend that texture be specified only on areas of the part that are drafted at least 3 degrees.
Polishing
We use manual mold polishing methods to apply the SPI-A3 finish.
Since there is not significant automation in this process, you should expect a significant cost increase, as it is labor intensive and time consuming to polish deep, narrow slots in molds. Polishing is time intensive and may also affect the lead time for your parts. In both Low-Volume Injection Molding and Production Injection Molding, any surface finish can be produced, including acid-etched finish.
Lead Time
Standard lead time for Injection Molding service is as follows: Process Rapid Injection Molding Low-Volume Injection Molding Production Injection Molding Standard Lead Time 10 days for 10x 10x 3 parts 20 days for 20x 20x 3 parts 15 20 days 4-6 weeks Fastest Lead Time 5 days, depending upon geometry 10 days, depending upon geometry 4 weeks
Lead times can change based on current factory load. Call your Quickparts Tooling Manager at 1.877.521.8683 to discuss your specific lead time requirements.
10