Table of contents

Plant specification
System concept
Technical data and performance curve............................................................................1
General arangement drawings........................................................................................2
Steam and water system................................................................................................3
Fuel oil system............................................................................................................4
Mission OC control panel drawing.................................................................................5
Spare part...................................................................................................................6
Instruction
MISSION OC boiler
Descriptions................................................................................................................7
Operation and maintenance...........................................................................................8
Feed and boiler water...................................................................................................9
Water level gauge......................................................................................................10
Safety valves.............................................................................................................11
Feed water system......................................................................................................12
Regulating feed water valve........................................................................................13
Chemical dosing pump...............................................................................................14
Oil detection equipment..............................................................................................15
Salinity alarm equipment............................................................................................16
Pressure atomising burner KBO
Descriptions..............................................................................................................17
Installation................................................................................................................18
Fuel oil pump unit......................................................................................................19
Operation and maintenance.........................................................................................20
MISSION OC Control System (Touch)
MISSION control system............................................................................................21
Operation of the panels...............................................................................................22
TABLE OF CONTENTS
Language UK i
Commisioning and service..........................................................................................23
Burner sequence diagram............................................................................................24
Flame safeguard.........................................................................................................25
Menu structure for panels............................................................................................26
TABLE OF CONTENTS
ii Language UK
Table of contents
Technical data and performance curve
Description Document ID Page
.
Technical data for boiler plant..................................... .................................. 1-2
Technical data for MISSION OC............................. .................................. 1-3
Technical data for fuel oil pumps................................. .................................. 1-6
Performance curve..................................................... .................................. 1-8
TABLE OF CONTENTS
Language UK 1-1 / 11
Technical data for boiler plant
1 General data

Request No./Order No.:...............................................103631-01-2, 103631-02-2

Hull No./Nos.:.................................................................................S1396, S1397
2 General plant data

Classification society:..................................................................................RINA

Sub-notification (Unattended operation):......................................................UMS

Service level:...........................................................................................Essential

Flange standard:...............................................................................................EN

Plant supply voltage:..............................................................................3 x 440 V

Plant control voltage:...................................................................................230 V

Pilot voltage:..................................................................................................24 V

Frequency:...................................................................................................60 Hz

Pressure gauge calibration:...................................Multi-scale(Bar, MPa, kg/cm2)

Thermometer calibration:...................................................................................C

Language on signs:....................................................................................English

Ambient air temperature:..............................................................................45 C
3 Documentation data

Language for manuals:..............................................................................English

Set of approval manuals:.................................................................15 sets/project

Set of working manuals:..................................................................15 sets/project

Set of instruction manuals:.............................................5 sets/1
st
ship, 4 sets/later

Set of CD-rom instruction manuals:......................................................1 sets/ship
TECHNICAL DATA FOR BOILER PLANT
1-2 / 11 Language UK
Technical data for MISSION OC
1 General data

Request No./Order No.:...............................................103631-01-2, 103631-02-2

Hull No./Nos.:.................................................................................S1396, S1397
2 Dimensions for boiler unit

Height to top of smoke outlet box:.........................................................5,390 mm

Diameter incl. insulation:.......................................................................2,820 mm

Extension length of the water level device:............................See general arr. drw.

Weight of boiler unit excl. water:..............................................................18.7 ton

Weight of boiler unit incl. water:..............................................................27.7 ton
3 Water/steam process data

Steam output, simultaneous operation:..................................................2,400 kg/h

Steam output, oil fired section:..............................................................1,200 kg/h

Steam output, exhaust section:..............................................................1,200 kg/h

Working pressure:............................................................................7.0 kg/cm(g)

Working temperature:..................................................................................170C

Max. allowable working pressure:....................................................9.0 kg/cm(g)

Feed water operation:..........................................................................Modulating

Feed water temperature, layout:.....................................................................80C
4 Data for pressure part

Boiler type:.......................................Vertical, composite smoke/water tube boiler

Boiler model:...............................................................................MISSION OC

Test pressure:......................................................1.5 x Design pressure kg/cm(g)

Protection of boiler body:...........................................................Silver(RAL9006)

Insulation thickness:...................................................................................75 mm

Cladding type:............................................................................................Trapez

Colour of insulation plates:..........................................................Blue(RAL5002)
TECHNICAL DATA FOR MISSION OC
Language UK 1-3 / 11
5 Combustion process data (oil-fired section)

Min. calorific value of diesel oil:.......................................................42,200 kJ/kg

Min. viscosity of diesel oil:..............................................................3 cSt. at 40C

Max. viscosity of diesel oil:............................................................12 cSt. at 15C

Density of diesel oil:.................................................................900 kg/m at 15C

Min. calorific value of fuel oil:..........................................................40,200 kJ/kg

Max. viscosity of fuel oil:.............................................................600 cSt. at 50C

Density of fuel oil:....................................................................991 kg/m at 15C

Turn down ratio on fuel oil:..............................................................................3:1

Fuel oil temperature before pre-heater:.........................................................60 C

Fuel oil viscosity at burner inlet:..............................................................8-10 cSt.

Fuel oil temperature at burner inlet:.............................................................145C

Air excess No. at 100% load:............................................................................1.2

Flue gas temperature (clean boiler):............................................................329 C

Air consumption at 100% load:.............................................................1,378 kg/h

Flue gas flow (approx.):........................................................................1,463 kg/h
6 Combustion process data (exhaust gas sec-
tion)

Main engine:..........................................................................................................

Engine load, design:...............................................................................90%MCR

Design condition:............................................................................................ISO

Exhaust gas flow:................................................................................80,900 kg/h

Inlet temperature of exhaust gas:.................................................................232 C

Outlet temperature of exhaust gas:..............................................................197 C
7 Data for pressure loss layout

Pressure loss across flue gas system, max.:...........................................10 mmWC

Pressure loss across boiler (oil-fired section):....................................40.0 mmWC

Pressure loss across boiler (exhaust gas section):................................120 mmWC
8 Data for burner

Burner type:.............................................................................Pressure atomising
TECHNICAL DATA FOR MISSION OC
1-4 / 11 Language UK

Burner regulation:...............................................................................Modulating

Model:............................................................................................KBO-E-R13M

Primary fuel:...................................................................................Heavy fuel oil

Secondary fuel:.......................................................................................Diesel oil

Burner capacity on diesel oil, min.:............................................................32 kg/h

Burner capacity on diesel oil, max.:...........................................................88 kg/h

Burner capacity on fuel oil, min.:...............................................................32 kg/h

Burner capacity on fuel oil, max.:..............................................................85 kg/h

Nozzle:.............................................................................................12-W2-70-60

Flame tube:................................................................................................OD200

Diffuser disc:.............................................................................................152x50

Colour of burner unit:...........................................................................RAL 3002
9 Data for control system

Insulation class:...................................................................................................F

Degree of protection:......................................................................................IP54

Colour of boiler control panel:................................................Munsell(7.5BG7/2)
10 Operational data for boiler plant

Operation:......................................................................................24h unattended

Automatic mode:.............................................................................................Yes

Manual mode:..................................................................................................Yes

Emergency mode:............................................................................................Yes
TECHNICAL DATA FOR MISSION OC
Language UK 1-5 / 11
Technical data for fuel oil pumps
1 General data

Project No.:.................................................................103631-01-2, 103631-02-2

Hull No./Project name:....................................................................S1396, S1397

Classification society/Local authority:.........................................................RINA

Pressure gauge calibration:.............................................................................MPa

Thermometer calibration:..................................................................................C

Language for signs:..........................................................................................UK

Colour of fuel oil pump unit:...................................................Munsell 7.5BG 7/2
2 Data for fuel oil pumps

Pump:................................................................................................Screw pump

Pump type:............................................................................SPZ10R28G8.3FW8

Delivery head:..........................................................................................3.3 Mpa

Relief valve set point (factory set):...........................................................3.6 Mpa

Oil temperature, maximum:........................................................................150 C

Pump capacity at 3 cSt:...............................................................................344 l/h

Pump capacity at 380 cSt:...........................................................................702 l/h

NPSH at 3 cSt. (including filter):...................................................................2.6m

NPSH at 380 cSt. (including filter):..............................................................4,0 m

Weight of fuel oil pump unit:.......................................................................106kg
3 Data for pump motor

Motor make:...................................................................................Branded motor

Motor type:..........................................................................................90S/M3AA

Power supply:...............................................................................3 x 440V, 60Hz

Rated output for motor:.............................................................................1.75kW

Revolutions:.........................................................................................3420r.p.m.

Ambient air temperature:...............................................................................45C

Starting method:..........................................................................................Direct

Starting current:..............................................................................................20A

Operating current (full load):.........................................................................3.4A
TECHNICAL DATA FOR FUEL OIL PUMPS
1-6 / 11 Language UK

Power consumption at 3 cSt:.....................................................................0.93kW

Power consumption at 380 cSt:.................................................................1.36kW

Numbers of cable gland size:.................................................................M20 x 1.5

Heating element(stand still):.......................................................................NONE

Thermostat protection:................................................................................NONE

Insulation class:...................................................................................................F

Degree of protection:.............................................................................Min. IP44
TECHNICAL DATA FOR FUEL OIL PUMPS
Language UK 1-7 / 11
Performance curve
PERFORMANCE CURVE A.1
1-8 / 11 Language UK
Fuel type
Calorific value
Working pressure
Feed water temperature
:
:
:
:
Heavy Fuel Oil
40200
7.0
80
kJ/kg
bar g
deg. C
Version no.: Page 1 of 4 2.0
Date:
User Initials:
Project Name: Project no:
Performance Calculation
MISSION OC
Standard Size: 1250 kg/h
09/12/2009
mva
STX Shipbuilding Co Ltd 103631
PERFORMANCE CURVE A.1
Language UK 1-9 / 11
Date:
User Initials:
Project Name: Project no:
Performance Calculation
MISSION OC
Standard Size: 1250 kg/h
09/12/2009
mva
STX Shipbuilding Co Ltd 103631
Version no.: Page 2 of 4 2.0
Fuel type
Calorific value
Working pressure
Feed water temperature
:
:
:
:
Heavy Fuel Oil
40200
7.0
80
kJ/kg
bar g
deg. C
PERFORMANCE CURVE A.1
1-10 / 11 Language UK
Date:
User Initials:
Project Name: Project no:
Performance Calculation
MISSION OC
Standard Size: 1250 kg/h
09/12/2009
mva
STX Shipbuilding Co Ltd 103631
Version no.: Page 3 of 4 2.0
Fuel type
Calorific value
Working pressure
Feed water temperature
:
:
:
:
Heavy Fuel Oil
40200
7.0
80
kJ/kg
bar g
deg. C
PERFORMANCE CURVE A.1
Language UK 1-11 / 11
Date:
User Initials:
Project Name: Project no:
Performance Calculation
MISSION OC
Standard Size: 1250 kg/h
09/12/2009
mva
STX Shipbuilding Co Ltd 103631
Version no.: Page 4 of 4 2.0
Fuel type
Calorific value
Working pressure
Feed water temperature
:
:
:
:
Heavy Fuel Oil
40200
7.0
80
kJ/kg
bar g
deg. C
General arangement drawings
Description Document ID Page
.
General arrangement for OC....................................... 04Y_056884............... 2-3
Gauge board drawing................................................. 61Z_054988............... 2-5
Water level control, Gestra, DN 100............................ 62Z_057339............... 2-7
Language UK 2-1 / 8
General arrangement for OC
GENERAL ARRANGEMENT FOR OC 04Y_056884#A.2
Language UK 1-3 / 8
Gauge board drawing
GAUGE BOARD DRAWING 61Z_054988#A.1
Language UK 1-5 / 8
Water level control, Gestra, DN 100
WATER LEVEL CONTROL, GESTRA, DN 100 62Z_057339#A.2
Language UK 1-7 / 8
Table of contents
Steam and water system
Tag Number Description Document ID Page
.
................................... Steam and water P&ID diagram.................................. X01_701406............... 3-3
................................... List of parts - steam/water........................................... X01_701406............... 3-5
C1, C301..................... Safety valve, DN 32/50, PN 40/16............................... 6040000006................ 3-7
C184, C484.................. Expansion joint, DN 50.............................................. 85Y_013421............... 3-9
C186, C486.................. Remote pull for safety valve....................................... K03_032121............... 3-11
C2............................... Stop valve, angle, DN 100, PN 25................................ 2511094..................... 3-13
C3, C303, C6, C7, C307
................................... Stop valve, straight, DN 25, PN 25.............................. 2501088..................... 3-14
C4, C304..................... Stop valve, straight, non return, DN 25, PN 25.............. 2641088..................... 3-15
C9, C10, C11............... Stop valve, straight, DN 8, PN 160.............................. 6220000002................ 3-16
C16, C198................... Stop valve, gate straight, DN 50, PN 10........................ 2531005..................... 3-17
C17.............................
Water level gauge with illuminator, left, model 26, DN
25, PN 40................................................................. 7010000436................ 3-18
C18.............................
Water level gauge with illuminator, right, model 26, DN
25, PN 40................................................................. 7010000435................ 3-20
C187, C487.................. Remote pull for water level gauge................................ K03_032122............... 3-23
C331, C431.................. Needle valve, straight, " x ", PN 400....................... 2541002..................... 3-25
C33............................. Pressure gauge, 100................................................. 6632973..................... 3-26
C35............................. Pressure switch RT30AW 1-10 Bar............................. 6310310..................... 3-27
C43............................. Pressure transmitter 0 - 10 barg................................... 8010000012................ 3-29
K8, K9........................ Temperature gauge.................................................... 8080000029................ 3-30
C162........................... U-tube manometer, 400 mm........................................ 8050000052................ 3-31
W1..............................
Pneumatic control valve, DN 15, PN 25, with DP actuator
and I/P positioner....................................................... 6050000001................ 3-32
W3.............................. Filter regulator with automatic drain............................ 2915101..................... 3-33
K5, K305..................... Temperature switch AHTs-20/a................................... 6320110..................... 3-34
3M23.......................... Chemical dosing unit................................................. 9296006004................ 3-35
H2, W32...................... LED indicator / limit switch........................................ 8001000002................ 3-37
M25............................ Sample cooler........................................................... 8750005..................... 3-39
M145.1........................ Control unit for oil detection equipment....................... 8210000025................ 3-41
M145.2........................ Ultrasonic sensor for oil detection equipment................ 8310000005................ 3-42
M146.1........................ Conductive electrode, type SL 700 E........................... 8620000082................ 3-43
M146.2........................ Control device, salinometer, type SL 700...................... 8210000032................ 3-44
M146.3........................ T-piece for salinity alarm equipment............................ 8500000115................ 3-45
C191........................... Water washing hose with nozzle.................................. 2941001..................... 3-46
S-C-9.......................... Spare parts box.......................................................... 6499402..................... 3-47
................................... Counter flange........................................................... K16_004096............... 3-49
TABLE OF CONTENTS
Language UK 3-1 / 49
Steam and water P&ID diagram
STEAM AND WATER P&ID DIAGRAM X01_701406#A.3
Language UK 3-3 / 49
List of parts - steam/water
Boiler plant:...................................................................................................................1 x MISSION OC
Request number:................................................................................................................................103631
Configuration number:.................................................................................................................................1
Hull number(s):........................................................................................................................S1396, S1397
Project number(s):................................................................................................103631-01-2, 103631-02-2
P&I diagram drawing number:...................................................................................................X01:701406
P&I diagram revision:....................................................................................................................................
Reading guide: List of Parts reflects parts delivered by Aalborg Industries.
Tag Numbers are given without the index used on the P&I diagram. E.g. C2" is found on the P&I Diagram
as "1C2" and "2C2" for boiler 1 and 2 respectively.
Tag no. Qty. Dim (DN) Application Type Datasheet or draw-
ing
Composite boiler (Qty. gives the number of parts per boiler)
C 1 N/A MISSION OC - 04Y:056884
C1 (a) 1 32/50 Safety valve Safety 6040 000006
C301 (a) 1 32/50 Safety valve Safety 6040 000006
C184 1 50 Expansion joint for safety valve - 85Y_013421
C484 1 50 Expansion joint for safety valve - 85Y_013421
C186 1 N/A Remote pull for safety valve - K03_032121
C486 1 N/A Remote pull for safety valve - K03_032121
C2 1 100 Main steam valve Stop 2511094
C3 1 25 Feed water valve Stop 2501088
C303 1 25 Feed water valve Stop 2501088
C4 1 25 Feed water valve Stop SDNR 264 1088
C304 1 25 Feed water valve Stop SDNR 264 1088
C6 1 25 Scum valve Stop 2501088
C7 1 25 Blow down valve Stop 2501088
C307 1 25 Blow down valve Stop 2501088
C9 1 1/2" Sample valve Stop 6220000002
C10 1 1/2" Air escape valve Stop 6220000002
C11 1 1/2" Gauge board valve Stop 6220000002
C16 1 50 Furnace drain valve Gate 2531005
C17 1 25/length 700 Water level gauge left Illuminated 7010000436
C18 1 25/length 700 Water level gauge right Illuminated 7010000435
C187 1 N/A Remote pull for water level gauge - K03_032122
C487 1 N/A Remote pull for water level gauge - K03_032122
C198 1 50 Drain valve for exhaust gas part Gate 2531005
W33 1 100 Water level meas. electrode - 8125000010
Feed water regulation valve (Qty. gives the number of parts per boiler)
LIST OF PARTS - STEAM/WATER
Language UK 3-5 / 49
W1 1 15 Feed Water Control Valve with pneumatic
actuator
Control 6050000001
W3 1 1/4" Filter regulator with automatic drain 0-10 bar(g) 2915101
Chemical d osing u nits - MISSION OC (Qty. gives the number of parts per composite boiler )
3M23 1 N/A Chemical dosing - 9296 006004
Smoke outlet - MISSION OC (Qty. gives the number of parts per boiler)
C179 1 - Smoke outlet - -
K5 (a) 1 1/2" Temperature switch, smoke outlet ATHs-20/a 6320110
Exhaust in/-outlet boxes - MISSION OC (Qty. gives the number of parts per boiler)
K305 (a) 1 1/2" Temp. switch (high), exhaust outlet ATHs-20/a 6320110
Remote indication - Steam pressure and Water level - MISSION OC (Qty. gives the number of parts per boiler)
H2 1 N/A Remote indication of Steam pressure Digital 8001 000002
W32 1 N/A Remote indication of Water level Digital 8001 000002
Sample coolers - MISSION OC (Qty. gives the number of parts per boiler)
M25 1 N/A Sample cooler SCS20 8750005
Gauge Board - MISSION OC (Qty. gives the number of parts per boiler)
C30 1 N/A Gauge board - 61Z:050512
C331 1 1/2'' Instrument stop valve - 254 1002
C431 2 1/2'' Instrument stop valve - 254 1002
C33 1 0-16 bar Pressure gauge - 663 2973
C35 1 0-10 Pressure switch, max. steam - 6310310
C43 1 0-10 Pressure transmitter - 8010 000012
K8
1 N/A
Temperature gauge Exhaust gas
inlet
8080 000029
K9
1 N/A
Temperature gauge Exhaust gas
outlet
8080 000029
C162 1 N/A U-tube manometer - 8050 000052
Control system - MISSION OC
3L2 1 - Local control panel - -
Tag no. Qty. Dim (DN) Application Type Datasheet or draw-
ing
Hot well - oil detection
M145.1 1 Control unit - 8210000025
M145.2 1 Sensor- 6 m cable - 8310000005
Salinity control
M146.1 1 N/A Conductive electrode SL 700 E 8620000082
M146.2 1 N/A Control device SL 700 8210000032
M146.3 1 25 T-piece - 8500000115
Water hose and spray gun
C191 1 N/A Water hose and spray gun (not shown on the di-
agram)
-
294 1001
Spare part box
S-C-9 1 N/A Spare part box (not shown on the diagram) - 6499402
Counter flanges
(c.fl.) 1 - Set of counter flanges (not shown on the P&I di-
agram)
- K16:004096
LIST OF PARTS - STEAM/WATER
3-6 / 49 Language UK
Type:

Safety valve, full lift

25.901
Size:

Nominal diameter: DN 32/50

Application:

To blow off saturated steam, air or water

Material:

Body: GGG 40.3

DIN-Material No.: 0.7043

Seat: X6 Cr Ni Mo Ti 17122
DIN-Material No.: 1.4571

Disc: X35 Cr 17
DIN-Material No.: 1.4122.05
Technical data:

Nominal pressure: PN 40/16

Weight: 14 kg

Flanges according to DIN

Inlet: DN 32, PN40

Outlet: DN 50, PN16

DATA SHEET
Tag No(s): C1, C301
Type No.: 6040
Version: A.2
Safety valve, DN 32/50, PN 40/16 6040000006
Language UK 3-7 / 49
Expansion joint, DN 50
1 --- NO TITLE ---
EXPANSION JOINT, DN 50 85Y_013421#A.3
Language UK 3-9 / 49
Tag No(s): C184, C484
Remote pull for safety valve
1
REMOTE PULL FOR SAFETY VALVE K03_032121#B.1
Language UK 3-11 / 49
Tag No(s): C186, C486
Type:

Stop globe valve, angle

Size:

Nominal diameter: DN 100

Application:

For steam and/or water flow

Material:

Body: GP240GH+N
DIN-materiale No: 1.0619+N

Seat: G19 9 Nb Si
DIN-materiale No: 1.4551

Disc: X20Cr13+QT
DIN-materiale No: 1.4021+QT
Technical data:

Nominal pressure: PN25

Weight: 34 kg

Flanges according to DIN

225
100
175
Disc
Seat
Body
235
1
7
5
3
6
3
0
0
190 / 8 x 22
DATA SHEET
Tag No(s): C2
Type No.: 6010
Version: B.2
Stop valve, angle, DN 100, PN 25 2511094
Language UK 3-13 / 49
Type:

Stop globe valve, straight

Size:

Nominal diameter: DN 25
Application:

For steam and/or water flow

Material:

Body: EN-GJS-400-18U-LT
DIN-materiale No: EN-JS1049

Seat: X20Cr13+QT
DIN-materiale No: 1.4021+QT

Disc: X20Cr13+QT
DIN-materiale No: 1.4021+QT
Technical data:

Nominal pressure: PN 25

Weight: 5.4 kg

Flanges according to DIN

140
1
3
1
9
0

8
5

/

4

x

1
4

2
5

1
1
5
160
Body
Disc
Seat
DATA SHEET
Tag No(s): C3, C303, C6, C7, C307
Type No.: 6010
Version: B.1
Stop valve, straight, DN 25, PN 25 2501088
3-14 / 49 Language UK
Type:

Stop check globe valve, screw down non

return, straight
Size:

Nominal diameter: DN 25
Application:

For steam and/or water flow

Material:

Body: EN-GJS-400-18U-LT
DIN-materiale No: EN-JS1049

Seat: X20Cr13+QT
DIN-materiale No: 1.4021+QT

Disc: X20Cr13+QT
DIN-materiale No: 1.4021+QT
Technical data:

Nominal pressure: PN 25

Weight: 5.4 kg

Flanges according to DIN

140
1
3
1
9
0

8
5

/

4

x

1
4

2
5
160

1
1
5
Disc
Seat
Body
DATA SHEET
Tag No(s): C4, C304
Type No.: 6030
Version: B.1
Stop valve, straight, non return, DN 25, PN 25 2641088
Language UK 3-15 / 49
Type:

Instrument stop cone valve, straight, with

security plate
Size:

G " x 12

Nominal diameter: DN 8
Application:

For steam, water and/or air

Material:

Body: C 22.8
DIN- Material No. 1.0460

Seat: X20 Cr13

DIN- Material No. 1.4021

Needle tip: X35 CrMo17

DIN- Material No. 1.4122
Technical data:

Nominal pressure: PN 160

Inlet: G " male DIN

19207, form R

Outlet: For steel tube 12

Weight: 0.8 kg
75
1/2 BSP
22
1
2
90
Security plate
1
1
5
DATA SHEET
Tag No(s): C9, C10, C11
Type No.: 6220
Version: A.2
Stop valve, straight, DN 8, PN 160 6220000002
3-16 / 49 Language UK
Type:

Stop valve, gate straight

Size:

Nominal diameter: DN 50
Application:

Sea water, fresh water, oil, steam etc.

Material:

Body: GG 25
Technical data:

Nominal pressure: PN 10

Max. temperature: 150 C

Weight: 11.5 kg
DATA SHEET
Tag No(s): C16, C198
Type No.: 6010
Version: A.2
Stop valve, gate straight, DN 50, PN 10 2531005
Language UK 3-17 / 49
Type:

Transparent water level gauge with illu-

minator.

Orientation: left

Model size:26

9030
Size:

Connection, nominal: DN 25

Connection, drain: 10
Pressure rating:

Pressure of unit, nominal: PN 40

Pressure of connection valves, nominal:

PN 40

Pressure of drain valve, nominal:PN 40

Connection type:

Connection type: Flanges according to

DIN
Application:

For boiler water level indicator

Material:

Body: Carbon steel 45#

Connection valve body: WCB

Drain valve body: WCB

Technical data

Connection valves type: PX

Weight:27.9 kg
Electrical specifications:

Power supply:230 V 50/60Hz

Bulb type: Clear glass

Bulb size: 100W

Socket type: E

Socket size: E 27
DATA SHEET
Tag No(s): C17
Type No.: 7010
Version: A.2
Water level gauge with illuminator, left, model 26,
DN 25, PN 40
7010000436
3-18 / 49 Language UK
Dimension:

H:700

H1: 530

H2:493

H3:250

H4:160

H5:115

H6: 350

L:84.5

L1: 130

L2: 100

L3: 230

W:125

W1: 105

W2: 290

D: 10

d: 3/4
L3
L2 L1
L
W
W2
A A
A A
H
3
H
6
H
5
H
4
H H
1
Drain connection D
Electrical
connection d
V
i
s
i
b
l
e

l
e
n
g
t
h

H
2
W1
DATA SHEET
Tag No(s): C17
Type No.: 7010
Version: A.2
Water level gauge with illuminator, left, model 26,
DN 25, PN 40
7010000436
Language UK 3-19 / 49
Type:

Transparent water level gauge with illu-

minator.

Orientation: right

Model size:26

9030
Size:

Connection, nominal: DN 25

Connection, drain: 10
Pressure rating:

Pressure of unit, nominal: PN 40

Pressure of connection valves, nominal:

PN 40

Pressure of drain valve, nominal:PN 40

Connection type:

Connection type: Flanges according to

DIN
Application:

For boiler water level indicator

Material:

Body: Carbon steel 45#

Connection valve body: WCB

Drain valve body: WCB

Technical data

Connection valves type: PX

Weight:27.9 kg
Electrical specifications:

Power supply:230 V 50/60 Hz

Bulb type: Clear glass

Bulb size: 100W

Socket type: E

Socket size: E 27
DATA SHEET
Tag No(s): C18
Type No.: 7010
Version: A.2
Water level gauge with illuminator, right, model
26, DN 25, PN 40
7010000435
3-20 / 49 Language UK
Dimension:

H:700

H1:530

H2:493

H3:250

H4:160

H5:115

H6:350

L:84.5

L1: 130

L2: 100

L3: 230

W:125

W1: 105

W2: 290

D: 10

d: 3/4
L3
L1 L2
L
W2
W
H
3
H
6
H
4
H
H
1
V
i
s
i
b
l
e

l
e
n
g
t
h

H
2
Drain connection D
A A
H
5
Electrical
connection d
A A
W1
DATA SHEET
Tag No(s): C18
Type No.: 7010
Version: A.2
Water level gauge with illuminator, right, model
26, DN 25, PN 40
7010000435
Language UK 3-21 / 49
Remote pull for water level gauge
1
REMOTE PULL FOR WATER LEVEL GAUGE K03_032122#C.1
Language UK 3-23 / 49
Tag No(s): C187, C487
Type:

Pressure gauge valve needle straight.

Size:

1/2 x 1/2
Application:

For instrument connections

Material:

Body: C22.8

DIN-material No. 1.0460

Technical data:

Nominal pressure: PN 400

Test connection: M20 x 1.5 mm threaded

male

Weight: 0.4 kg
DATA SHEET
Tag No(s): C331, C431
Type No.: 6210
Version: C.1
Needle valve, straight, " x ", PN 400 2541002
Language UK 3-25 / 49
Type:

Pressure gauge
Size:

100
Application:

For all gaseous and liquid media

Material:

Case: Stainless steel

Socket: Cu-alloy

Liquid filling: Glycerine

Technical data:

Measuring unit: bar Mpa - kg/cm

Measuring range: 0 16 / 1.6 /16 with

mechanical stop

Connection: BSP 1/2-m

Operating temperature:
Ambient: -20to + 60C
Medium, max.: + 60C

Protection: IP 65
107

1
0
0
3
0
81.5
8
BSP 1/2-m
bar
MPa=bar x 0.1
kg/cm
0
0
16
16
DATA SHEET
Tag No(s): C33
Type No.: 8050
Version: C.1
Pressure gauge, 100 6632973
3-26 / 49 Language UK
DATA SHEET
Tag No(s): C35
Version: B.2
Pressure switch RT30AW 1-10 Bar 6310310
Language UK 3-27 / 49
Tag No(s): C35
DATA SHEET
Tag No(s): C35
Version: B.2
Pressure switch RT30AW 1-10 Bar 6310310
3-28 / 49 Language UK
Type:

Pressure transmitter
Range:

0 10 barg
Application:

The pressure transmitter converts pres-

sure to an electric signal. The units are
supplied as two wire transmitters with an
output signal of 4-20 mA. The output
current is linearly proportional to the in-
put pressure.
Material:

Housing: Stainless steel with ceramic

measuring cell and electronics module.
The temperature-compensated ceramic
measuring cell has a thin-film strain
gauge which is mounted on a ceramic di-
aphragm.

Process connection: Stainless steel

Gasket: Viton
Technical data:
Electrical specification:

Current output signal: 4 to 20 mA

Voltage output signal (only measuring

range > 1 bar: 0.10 VDC

Power supply terminal voltage for cur-

rent output: 10.36VDC
Accuracy:

Response time T99: < 0.1 s

Influence of ambient temperature at start

of scale: 0.25%/10K (0.25%/10K) of full
scale value

Influence of ambient temperature at full

scale value: 0.25%/10K (0.25%/10K) of
full scale value
Mechanical:
Process temperature: 30C to +120C
Ambient temperature: 25C to +85C

Degree of protection to EN 60529: IP65

Weight: 0.25 kg
Connection diagram:
1
2
7
2
0
G 1/2 -m
27
SW 27
50
PG 11
1+
I Output current
U Power supply
R Load
Connections:
1 (+U )
2 (-U )
0
B
L
B
B
+
U
B
R
L
I
o
2-
DATA SHEET
Tag No(s): C43
Type No.: 8012
Version: A.2
Pressure transmitter 0 - 10 barg 8010000012
Language UK 3-29 / 49
Type:

Temperature gauge
Size:

100
Application:

For marine applications

Material:

Case: AISI 304 natural

Probe: AISI 316

Window: Acrylic

Liquid filling: Silicone

Technical data

Measuring range: 0 to 400C

Capillary tube: 10 m

Connection: None (smooth sensor), con-

nector supplied separately

Ambient temperature: -40 to +100C

4
5
0
4
8

1
0
8
51
C
0
100
200
300
400
116
13
3 x 6, PCD 116
DATA SHEET
Tag No(s): K8, K9
Type No.: 8080
Version: A.2
Temperature gauge 8080000029
3-30 / 49 Language UK
Type:

U-tube manometer, 400 mm

1221 M-400-W/M
Application:

For determining velocity and static pres-

sure, leakage, fan and blower efficiency,
filter resistance and differential gas pres-
sures.
Material:

U-tube: Shatter proof clear butyrate tub-

ing

Base plate: Aluminium

Technical data:

Range: 200-0-200 mm H2O

Accessories:

One ounce bottle of fluorescein green

dye concentrate gauge fluid
3
5
1
9
.
5
4
2
5
1
7
1
2
1
.
5
75
28 23.5
Cutting ring 12
A
A - A
A
7
0
0
7
2
8
7
7
200
100
200
100
0
DATA SHEET
Tag No(s): C162
Type No.: 8050
Version: A.2
U-tube manometer, 400 mm 8050000052
Language UK 3-31 / 49
Type:

Control globe valve, straight with pneu-

matic actuator and I/P positioner

23.470, DP 32
Size:

Nominal diameter: DN 15
Application:

For control of air, gas, water, steam, and

oil flow
Material valve:

Body: GGG 40.3

DIN -Material No. 0.7043

Seat: X20 Cr13

DIN Material No. 1.4021.05

Plug: X20 Cr13

DIN Material No. 1.4021.05

Stuffing box: PTFE V-ring unit(-10C to

+ 220C)
Technical data, valve:

Nominal pressure: PN 25

Positioning ratio: 50:1

Flow characteristic: Equal percentage

Kvs value:1.6 m/h

Stroke:20 mm

Plug type: Parabolic shaft guided

Flanges according to DIN

Technical data, actuator:

Control signal: 0.4 1.2bar

Max. permissible closing pressure:

40 bar

Diaphragm area: 250 cm

Max. air supply pressure: 6 bar

Action:Spring closes on air failure

Technical data, I/P positioner:

Air connection inlet: G

Inlet air supply: 1.4 to 7 bar, instrument

air

Air inlet consumption in stable state:

0.036 Nm/h

Cable inlet: M20 x 1.5

Input signal: 4-20 mA

Ambient temperature: -30C to +80C

Protection: IP65
Technical data unit:

Weight: 18 kg
Installation:

Only as shown in the picture

225
250
2
7
0

1
5

6
5
/
4
x

1
4

9
5
4
7
0
Body
Plug
Seat
Stuffing box
130
I/P Positioner
Actuator
Stroke indicator
Hand wheel
DATA SHEET
Tag No(s): W1
Type No.: 6050
Version: B.1
Pneumatic control valve, DN 15, PN 25, with DP
actuator and I/P positioner
6050000001
3-32 / 49 Language UK
Type:

Filter regulator with automatic drain

Size:

Connections ports 1/4 BSP

Gauge ports 1/8 BSP

Application:

Instrument air for regulating pressure

Technical data:

Medium: instrument air only

Max. inlet pressure: 17 bar

Operating temp.: 20 C to + 65 C
Filter element: 5 m

Recommend pressure regulating range:

0.14-7.0 bar

Pressure gauge: 0 10 bar

Weight: 0.4 kg
Material:

Body: Steel

Bin: Steel

Handle: Acetal
Flow characteristics
O
u
t
l
e
t

p
r
e
s
s
u
r
e

[
b
a
r
]
Air flow [ dm /s]
3
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8 9 10
Inlet pressure 7 bar
Connections ports
D
i
s
m
a
n
t
e
l

l
e
n
g
t
h

1
3
8
S
W
1
9
3
8
41
9
9
7 1
4
30
2
8
M
a
x
.

6
6
6
18
6
2
3
8
2
.
5
4
4
31
R
1
9
G
a
u
g
e

p
o
r
t
s
Bin
Body
Handle
Fitting
7
.
5
DATA SHEET
Tag No(s): W3
Type No.: 8000
Version: B.1
Filter regulator with automatic drain 2915101
Language UK 3-33 / 49
Type:

Temperature switch

ATHs-20/a
Application:

For exhaust gas

Material:

Steel
Technical data:

Measuring range: + 20 - +500 C

Protection: IP54

Cable entry: PG 13.5

G 1/2
3
0
0
6
7
8
5
6
6
8
94
DATA SHEET
Tag No(s): K5, K305
Type No.: 8070
Version: A.2
Temperature switch AHTs-20/a 6320110
3-34 / 49 Language UK
Type:

Dosing pump CNPA -1601 PPE2 with

chemical tank.
Application:

For chemical dosing, modulating feed

water regulation.

For boiler with Max. design pressure: 12

bar
Material:

Pump
Liquid end: Polypropylene
Valves: Polypropylene
Seals: EPDM
Balls: Ceramic

Chemical tank: Polyethylene

1
5
9
5
9
0
410
Feed line to boiler
Relief valve, item 6000 000088
6/ 4 x 5000 mm PE Hose
Air escape valve
Dosing pump, item 5540 000313
incl. air escape valve,
hoses, dosing valve and
non return valve
Manual stirrer, item 8500 000716
60 l chemical tank, item 8500 000715
Dosing valve, spring loaded
Non return valve
Cooling neck 200 - 300 mm
Yard supply
Technical data:

Max. outlet pressure: 16 bar

Max. inlet pressure: 8 bar

Capacity at 16 bar: 1.0 l/h

Stroke at 16 bar: 0.10 ml

Capacity at 8 bar: 1.4 l/h

Stroke at 8 bar: 0.13 ml

Max. frequency: 180 stroke/min

Suction lift: 6 m WC

Max. ambient temperature at at max.

counter pressure: 45C

Wattage: 10 W

Peak current: 0.5 A

Fuse (placed behind the control pan-

el): 0.16 AT

Enclosure rating: IP 65

Insulation class: F

Motor: 1 phase AC

Control supply: 230 V 50/60 Hz

Weight: 8 kg
Pover connection
96
18
Customer connection 1/2
Dosing valve

3
0
35
DATA SHEET
Tag No(s): 3M23
Type No.: 9296
Version: B.1
Chemical dosing unit 9296006004
Language UK 3-35 / 49
1,6
1,4
1,2
1
0,8
0,6
0,4
0,2
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
0
I
/
h
180 strokes/min
135 strokes/min
90 strokes/min
45 strokes/min
Stroke length
CNPa 1601 at medium back pressure
2
1,5
1
0,5
0
1 2 3 4 8 11 13 16
Back pressure
Correcti on factor
DATA SHEET
Tag No(s): 3M23
Type No.: 9296
Version: B.1
Chemical dosing unit 9296006004
3-36 / 49 Language UK
Type

LED indicator/limit switch

5714B
Application:
1 2
4
8
96
5714
OK
1
2
0

The 5714 with 2 relay outputs is designed

for digital readout of current / voltage or
temperature signals.
Relay outputs:

Are selected as either a make or a break

function. The relays can be used as a trip
amplifier.

Two yellow front LEDs indicate the re-

lay status. The relays can be set up with
either delayed on or off. Active relay can
be selected for either an increasing or de-
creasing signal. The arrow keys can be
used for fast change of the set point.
Technical data:

Panel cut out: 44.5 x 91.5 mm

Weight: 230 g
Electrical specifications:
Common specifications:

Supply voltage:
Max. voltage: 24230 VA C, 10%50
60Hz
24250 VDC 20%

Internal consumption: 2.7W

Max. consumption: 3.0 W

Auxiliary voltages:
2-wire supply: 2516 VDC / 020 mA

EMC immunity influence: < 0.5% of

reading

Max. wire size: 1 x 2.5 mm

Relative air humidity:< 95% RH (non

condensing)

Tightness (mounted in a panel): IP65

Voltage input:

Measurement range: -20mV...12 VDC

Program measurement range :

01/0,21/010/210VDC
Input resistance: nominal 10 M
Current input:

Measurement range: -1...25 mA

Program, measurement range:

020 and 420mA

Input resistance:
Nominal20 + PTC 25

Sensor error detection: loop break

420mA..Yes
Display:

Display readout: -1999999 (4 digits)

Decimal point: programmable

Digit height: 13.8 mm

Display updating: 2.2 times/s

Input outside input range is indicated by:

Explanatory text
Relay outputs:

Relay function: setpoint

Hysteresis, in % display counts:

0.125%/12999

On and Off delay: 03600s

Max. voltage: 250 VRMS

Max. current: 2 A / AC

Max. AC power: 500 VA

Max. current at 24 VDC: 1A

Sensor error action: Make / break/hold

DATA SHEET
Tag No(s): H2, W32
Type No.: 8001
Version: B.1
LED indicator / limit switch 8001000002
Language UK 3-37 / 49
4
1
4
2
4
3
4
4
4
5
4
6
3
1
3
2
4
1
4
2
4
3
4
4
4
5
4
6
4
1
4
2
4
3
4
4
4
5
4
6
4
1
4
2
4
3
4
4
4
5
4
6
4
1
4
2
4
3
4
4
4
5
4
6
4
1
4
2
4
3
4
4
4
5
4
6
-
+
4
1
4
1
4
2
4
2
4
3
4
3
4
4
4
4
4
5
4
5
4
6
4
6
+
-
T
x
-
+
+
-
R
T
D
,

2
-
w
i
r
e
S
u
p
p
l
y
I
n
p
u
t
:
C
o
n
n
e
c
t
i
o
n
s
O
u
t
p
u
t
:
T
C
V
o
l
t
a
g
e
P
o
t
e
n
t
i
o
m
e
t
e
r
R
T
D
,

3
-
w
i
r
e
2
-
w
i
r
e

t
r
a
n
s
m
i
t
t
e
r
C
u
r
r
e
n
t
R
T
D
,

4
-
w
i
r
e
2
1
2
2
2
3
2
4
2
5
2
6
R
e
l
a
y
s
R
1
R
2
1
1
1
2
+
-
C
u
r
r
e
n
t
m
A
Block Diagram:
DATA SHEET
Tag No(s): H2, W32
Type No.: 8001
Version: B.1
LED indicator / limit switch 8001000002
3-38 / 49 Language UK
Type:

Sample cooler
Size:

SCS 20
Application:

The sample cooler is designed for taking

manual samples of boiler water for anal-
ysis. The cooling water is turned on and
the sample inlet valve is adjusted until a
sample of boiler water is obtained at a
suitable temperature. For manual sam-
pling it is not normally necessary to
measure sample or cooling water flow
rates.
Cooling water out 1/2 BSP
Customer supply
Cooling water in1/2 BSP
Customer supply
3. Compression fittings
for sample in 1/4 BSP
2. Sample inlet valve
1/4 BSP (each ends)
4. Cooling water
inlet valve 1/2 BSP
Sample in 6 mm O/D
Customer supply
1. Sample cooler
Sample out
Material:

Sample cooler: austenitic stainless steel

grade 316L

Cooling water inlet valve: stainless steel

Sample inlet valve: stainless steel.

Compression fitting: carbon steel

Technical data:

Coil design pressure: 32 bar g

Coil design temperature: 300C

Body design pressure: 10 bar g

Body design temperature: 100C

1
3
90
DATA SHEET
Tag No(s): M25
Type No.: 7050
Version: C.1
Sample cooler 8750005
Language UK 3-39 / 49
Installation:

Fit the SCS 20 so that the bottom of the

unit is accessible for the collection of the
cooled sample.

Connect the cooling water inlet in

nominal bore pipe via an inlet valve.

The cooling water outlet should be piped

to an open drain or tundish.

The sample inlet pipe should be in 6 mm

O/D tubes.

The sample inlet to the cooler can be tak-

en direct from a boiler or steam line iso-
lating valve.
Operation:

Sample pipe work will become very hot

under normal working conditions, and
will cause burns if touched.

Open the cooling water inlet valve first

and ensure that a flow can be seen at the
cooling water outlet.

It is essential that cooling water is flow-

ing before opening the sample inlet
valve.

Gradually open the samples inlet valve

and regulate the flow to achieve a cooled
sample at about 25C.

Allow the sample to run for a while be-

fore collection. This will ensure that a
true sample is collected for analysis.

When enough liquid has been collected

close the sample inlet valve first and then
the cooling water inlet valve.

After closing the sample inlet valve the

sample out connection may drip for a few
minutes while the coil drains.
Performance:

When it is required to predict the per-

formance of the sample cooler system,
the table below gives the sample outlet
temperature to be expected for two boiler
pressures an for two cooling water flow
rates.
Example

A sample flow rate of 30 l/h is required

from a boiler operating at 10 barg. For a
cooling water flow rate of 0.4 l/s, from
the table the sample outlet temperature
would be 4K (4C) above the cooling
water inlet temperature. If the cooling
water is 15C, the sample temperatures
would be 19C.
Sample flow rate Cooling water flow rate
0.25 l/s (900 l/h)
Cooling water flow rate
0.4 l/s (1440 l/h)
Boiler pressure
10 barg 20 barg 10 barg 20 barg
l/h l/min Sample outlet temperature above cooling water inlet temperature K (C)
10 0.17 3 3 1 1
20 0.33 5 5 2 3
30 0.50 7 9 4 5
40 0.67 8 10 5 7
50 0.83 10 12 6 8
60 1.00 11 13 7 10
80 1.33 12 16 8 12
100 1.67 15 19 9 14
120 2.00 17 22 10 16
Table 1
DATA SHEET
Tag No(s): M25
Type No.: 7050
Version: C.1
Sample cooler 8750005
3-40 / 49 Language UK
Type:

Control unit for oil detection equipment

Application:

The control unit is operated together with

an ultrasonic sensor.

The equipment provides for oil detection

in feed/make-up water.
Material:

Control device cabinet: Polycarbonate

Technical data:

Power supply (selector switch):

110/120V or 220/240V AC

Relay output:DPCO

Enclosure:IP 65

Holes for glands 3 of 16

40
4
0
1
2
0
8
8
130
188
6
0
7
5
160
200
Holes for mounting
Alarm
Normal
Fault
Holes for glands
DATA SHEET
Tag No(s): M145.1
Type No.: 8210
Version: A.2
Control unit for oil detection equipment 8210000025
Language UK 3-41 / 49
Type:

Ultrasonic sensor for oil detection equip-

ment
Application:

The ultrasonic sensor is operated togeth-

er with a control unit.

The equipment provides for oil detection

in feed/make-up water.
Material:

Sensor: Stainless steel

Technical data:

Temperature:-70C to 150C

Design of duty:Chemical interface

Liquid type:Clean, viscous with solids

Cable:6 metre

"

2
2
1
1
10 20 25
258
152 26
DATA SHEET
Tag No(s): M145.2
Type No.: 8310
Version: A.2
Ultrasonic sensor for oil detection equipment 8310000005
3-42 / 49 Language UK
Type:

Conductive electrode, type SL 700 E

Application:

The conductive electrode is used in com-

bination with a control device to measure
and supervise the salinity of feed water.
Technical data:
Instrument:

Salinity range: 0 100 ppm (sea salt)

Accuracy: +/- 10%

Electrical:

Total cable length: max. 200 m

Connection to control device via junction

box:
Sensor pin 1 to pin 11 (white)
Sensor pin 2 to pin 12 (black, white)
Sensor pin 3 to pin 13 (red)
Sensor pin 4 to pin 14 (shield)
Sensor pin 5 to pin 15 (black, red)
Installation:

The conductive electrode must be instal-

led in the supplied T-piece (item 8500
000115). The cable must be connected to
the control device via a junction box (not
AI supply).
Gold-plated
electrodes
Packing
1
2
3
4
5
6
Connector
plug:
6 pol GLC
Cable lenght:
2.5 metre
DATA SHEET
Tag No(s): M146.1
Type No.: 8620
Version: B.1
Conductive electrode, type SL 700 E 8620000082
Language UK 3-43 / 49
Type:

Control device for salinometer, type SL

700
Application:

The control device is used in combina-

tion with a conductive electrode to meas-
ure and supervise the salinity of feed wa-
ter.
Technical data:
Instrument:

Salinity range: 0 100 ppm (sea salt)

Accuracy: +/- 10% of displayed value

Adjustable alarm range:1 100 ppm

Display: LED indication bar

Electrical:

Mains supply: 90 115 VAC or

190 230 VAC, 50 60 Hz

Mains current: mains supply must be se-

cured against over current externally by
using a fuse (max. 100 mA)

Power: max. 3.5 W

Cable connections:
Terminal 1-4: mains supply
Terminal 5-10: relay contacts for alarm
and solenoid
Terminal 11-16: electrode unit
Terminal 17-18: 4-20 mA current loop
mA =(0.16 x ppm) + 4 mA)

Relay contacts: 8 A / 24 VDC

105
8
6
DATA SHEET
Tag No(s): M146.2
Type No.: 8210
Version: B.1
Control device, salinometer, type SL 700 8210000032
3-44 / 49 Language UK
Type:

T-piece for salinity alarm equipment

Size:

DN 25
Application:

Housing for salinity electrode

Material:

Housing: RG 5

Nut for electrode: RG5

Technical data:

Nominal pressure: PN16

Flanges according to DIN 2501

Weight: 2.65 kg
110
115
PCD 85
4 x 12
10
DATA SHEET
Tag No(s): M146.3
Type No.: 8500
Version: B.1
T-piece for salinity alarm equipment 8500000115
Language UK 3-45 / 49
Type:

Water washing hose with nozzle

Size:

V-nozzle: 12 mm

Length: 15 metre (hose)

Inner diameter: 52 mm (hose)

Application:

For spraying of water

Material:

Hose: full-synthetic material (polyester)

woven in 1/1 binding, with inner rubber
lining
Technical data:

Max allowable working pressure: 20 bar

Water temperature area: -30C-+60C

Weight: 5.5 kg
Nozzle,
item No. 294 1101
Couplings (2 Storz) Hose,
item No. 294 1001
Couplings (2 Storz),
item No. 294 1201
2 BSP connection
(male)
10
20
30
40
50
60
70
80
90
100
110
120
130
140
160
170
180
200
190
150
I/min
1 2 3 5 4 6 7 8 9 10 Bar
210
Water flow
DATA SHEET
Tag No(s): C191
Type No.: 8615
Version: A.2
Water washing hose with nozzle 2941001
3-46 / 49 Language UK
Type:

Spare parts box

Included cabs lock item No. 4234331

Application:

For holding tools and spare parts

Technical data:

Material: Steel

Colour: Munsell No. BG 7/2

3
0
0
400 800
DATA SHEET
Tag No(s): S-C-9
Type No.: 8500
Version: C.1
Spare parts box 6499402
Language UK 3-47 / 49
Counter flange
1 --- NO TITLE ---
COUNTER FLANGE K16_004096#C.1
Language UK 3-49 / 49
Table of contents
Fuel oil system
Tag Number Description Document ID Page
.
................................... Fuel oil P&ID diagram............................................... 94X02_701407............ 4-3
................................... List of parts - fuel oil supply for Pressure Jet................. 94X02_701407............ 4-4
F1............................... Pressure atomising burner, modulating......................... 5561000011................ 4-5
F236........................... Quick closing valve unit............................................. 4800000078................ 4-6
G115........................... Three-way valve (incl. micro switch)........................... 6070000038................ 4-7
G340........................... Flow meterunit DN 20, ring ling.................................. 71Z20_044014............ 4-11
included in G340.......... Flow meter, VZO 20.................................................. 7060000015................ 4-13
included in G340.......... Filter; DN 20, PN 25.................................................. 7040000071................ 4-14
included in G340.......... Stop valve, ball, straight, DN 32.................................. 87D3066.................... 4-15
included in G340.......... Differential pressure switch, 0 - 4 Bar.......................... 8040000008................ 4-16
included in G340.......... Stop valve, ball, straight, DN 20.................................. 87D3064.................... 4-17
G147........................... Fuel oil supply pump unit, with filter, 10-R 28.............. 9294002051................ 4-19
G224........................... Remote start/stop box................................................. 8001000005................ 4-21
................................... Counter flange........................................................... K16_004096............... 4-23
TABLE OF CONTENTS
Language UK 4-1 / 23
Fuel oil P&ID diagram
FUEL OIL P&ID DIAGRAM 94X02_701407#A.3
Language UK 4-3 / 23
List of parts - fuel oil supply for Pressure
Jet
Boiler plant:...................................................................................................................1 x MISSION OC
Request number:................................................................................................................................103631
Configuration number:.................................................................................................................................1
Hull number(s):........................................................................................................................S1396, S1397
Project number(s):................................................................................................103631-01-2, 103631-02-2
P&I diagram drawing number:................................................................................................94X02:701407
P&I diagram revision:...........................................................................................................(a) 23 Apr 2010
Reading guide:
List of Parts reflects parts delivered by Aalborg Industries.
Tag Numbers are given without the index used on the P&I diagram. E.g. C2" is found on the P&I Diagram
as "1C2" and "2C2" for boiler 1 and 2 respectively.
Tag no. Qty. Dim (DN) Application Type Datasheet or draw-
ing
Pressure Jet Burner
F1 1 R13M Burner unit KBO-E 5561000011
F113 1 R 1/2" Flexible hose - 8615000050
F115 1 R 1/2" Flexible hose - 8615000050
F236 1 N/A Pressure control unit with quick close
valves
- 4800000078
Change over valve(s)
G115 1 25 Three-way valve (incl. micro switches) - 6070000038
Oil flowmeter
G340 1 Flowmeter_DN20
Connection
_DN32
Oil flow meter incl. filter & bypass - 71Z20_044014
Fuel oil supply pump
G147 1 25/20 Fuel oil supply pump unit Allweiler 9294002051
G224 (a) 1 N/A Remote start/stop box - 8001000005
Control system
3L2 1 - Local control panel - -
Counter flanges
(c.fl.) 1 - Set of counter flanges (not shown on the
P&I diagram)
- K16:004096
LIST OF PARTS - FUEL OIL SUPPLY FOR PRESSURE JET
94X02_701407#A.3
4-4 / 23 Language UK
Type:

Pressure atomising

Operation: Modulating

KBO-R13M-E
Application:

For burning of diesel oil and heavy fuel

oil
Technical data:

Viscosity of diesel oil min.: 4 cSt. at

20C

Viscosity of diesel oil max.: 40 cSt. at

50C

Viscosity of heavy fuel oil max.: 700 cSt.

at 50C

El-preheater: 7.2 kW

Insulation class: F

Weight:110 kg
Installation:

The burner is left hinged. It can be right

hinged on request.
Dimension:

L: 1000

L1: 200

H: 620

H1: 420

W: 920

W1: 490

W2: 430

O.D.: 200

r: 1150
H
W
W
2
O
.
D
.
W
1
H
1
L L1
r
The items are not included
in burner item No.
In- and outlet oil hoses
1 BSP x L = 2000 mm
item No. 8615 000050
DATA SHEET
Tag No(s): F1
Type No.: 5561
Version: A.2
Pressure atomising burner, modulating 5561000011
Language UK 4-5 / 23
Type:

Quick closing valve unit

Material:

Ball valve: A105

Pressure regulating valve: 40

Pipes: St.37.4NBK
Technical data:

Max temperature: 180 C

Max pressure: 40 bar

L
L1 L2
W
W
1
W
2
W
3
W
4
Oil from tank
pipe 22
MAX. Pressure
to valve 40 bar
Oil to tank
pipe 22
Oil to burner
Working pressure
25- 30 bar
Connect to hose 18
Oil from burner
Connection to hose 18
L3
L4
L5
W
5
ZCP21
Dimension

L = 322.5

L1 = 257

L2 = 69.5

L3 = 466

L3 = 466

L4 = 156

L5 = 33

W = 266

W1 = 49

W2 = 32

W3 = 124.5

W4 = 185

W5 = 260
DATA SHEET
Tag No(s): F236
Type No.: 4800
Version: C.1
Quick closing valve unit 4800000078
4-6 / 23 Language UK
DATA SHEET
Tag No(s): G115
Version: D.1
Three-way valve (incl. micro switch) 6070000038
Language UK 4-7 / 23
DATA SHEET
Type:
Three-way valve, ball
LB 283 BW, reduced bore
Size:
DN 25
Application:
For air, steam, or oil flow
Material
Body: ASTM A105
End connections: ASTM A105
Technical data:
Min./max. temperature at 30 bar:
- 29C to + 230C
End connections: Butt weld according to
ASME/ANSI B16.25 - XS-80
Pipe size: DN 25
Weight: 5 kg
Installation:
Information and caution before installation
of the valve:
Pipe must be free of tension.
Pipe must be flushed to clean the dirt,
burrs calamines, welding residues etc.
which would damage the ball and seat.
The valve must be kept in open position
during installation. Protective plastic
covers must not be removed before the
installation work commences.
At the moment of the shipment the ball is
lubricated with a pure vaseline oil,
which can be easily removed with a
solvent, if required.
Ball valves normally have a space
between ball and inside cavity of the
body, which could trap the product, care
should be taken to drain the cavity.
Instruction for welding the valve on the pipe
line:
Tack weld in four points on both end-
connections.
Lift out the centre part to protect the
gaskets against damage and complete
the welding.
Insert the centre part and ensure easy
operation.
Port 1 Port 2
Port 3
Port 3
Port 2 Port 1
L-Bore
150
75
114
193
8
6
End connections
Detail A
Bolt
Centre part
Language UK Page 1/1
Three-way valve, ball DN 25 6070 000052
Type No.: 6070
Version: A
6070 000038
1/3
Tag No(s): G115
DATA SHEET
Tag No(s): G115
Version: D.1
Three-way valve (incl. micro switch) 6070000038
4-8 / 23 Language UK
EGO SWITCHBOX
TYPE M
Description:
EGO switchbox with integrated mikroswitches to be used
for remote as well as visual indication of valve position
The switchbox include bracket for mounting on a
pneumatic actuator. With use of a special bracket the box
can be mounted on a gearbox or directly on a valve.
ns o i t a k i f i c e p S
s u B t a n o b r a c y l o P
l e s k A M O P
e v i k s m a K n o l y N
e d a l p d n u B x a m i t r e P
d e v o h m a K g n i s s e M
d a r g s g n i n t T 5 6 P I
r o t a k i d n I M O P
g n i n t t s g n i r - O n o t i V
Specifications
Cam
Box
Cam plate
Ground plate
Shaft
Protection
Position indicator
O-ring
Brass
Aalborg Industries Data sheet No. 6070 000038 2/3
DATA SHEET
Tag No(s): G115
Version: D.1
Three-way valve (incl. micro switch) 6070000038
Language UK 4-9 / 23
EGO SWITCHBOX
TYPE M
: a t a d k s i n k e T
M X O B O G E I X O B O G E N X O B O G E
l a t n a t k a t n o K 1 + 1 1 + 1 1 + 1
e p y t t k a t n o K h c t i w s o r k i M v i t k u d n i P N P r u m a N
t a k i r b a F l l e w y e n o H l l e w y e n o H s h c u F + l r e p p e P
e p y T C 1 B T 0 1 0 C 5 V L - 3 V P 9 A - 2 S F 2 9 9 5 V - N - 3 V - 2 J N
g n i d n p S C A V 0 5 2 . x a m C D V 0 5 - 6 , 9 C D V 8
g u r b r o F - 0 1 A m -
g n i n t s a l e b . x a M A ) 3 ( 0 1 A m 0 0 2 -
s n e v k e r f . x a M - z H K 2 z H K 1
r u t a r e p m e t t n e i b m A 5 5
o
5 8 + l i t C
o
C 5 2
o
5 7 + l i t C
o
C 5 2
o
0 0 1 + l i t C
o
C
H x B x L r e n o i s n e m i D 7 6 x 0 8 x 2 8 7 6 x 0 8 x 2 8 7 6 x 0 8 x 2 8
Aalborg Industries Data sheet No. 6070 000038 3/3
Type of switch
No. of switches
Manufacture
Manufacture item No.
Voltage
Consumption
Max. load
Max. frequency
Ambient temperature
Dimensions
Technical data
Flow meterunit DN 20, ring ling
1 --- NO TITLE ---
FLOW METERUNIT DN 20, RING LING 71Z20_044014#C.1
Language UK 4-11 / 23
Type:

Flow meter with flanges

VZO 20
Application:

Measuring of oil consumption

Technical data:

Nominal pressure: 25 bar

Installation length: 165 mm

Max. temperature: 130C

Ambient temperature: -10 to +70C

Flow rate:
Maximum: 1500 l/h
Nominal: 1000 l/h
Minimum: 30 l/h
Approx. starting: 12 l/h

Flanges: according to DIN 2501 / SN

21843

Weight: 4.5 kg
165
1
1
5

1
0
5
5
4
DATA SHEET
Tag No(s): included in G340
Type No.:7060
Version: A.2
Flow meter, VZO 20 7060000015
Language UK 4-13 / 23
Type

Filter

23.050
Size:

Nominal diameter: DN 20
Application

For mechanical cleaning of different me-

dias in tube systems before control
valves, reduction valves, pumps, steam
traps and flow meters
Material:

Body: EN-GJS-400-18U-LT
Din-Material No. EN-JS1049

Cover: EN-GJS-400-18U-LT
Din-Material No. EN-JS1049

Screen: X 5 CrNi 18-10

Din-Material No. 1.4301
Technical data:

Nominal pressure: PN 25

Filtration: 0.25

Flange according to DIN

Weight: 4 kg
Installation:

The filter can be mounted in optional po-

sitions with the flow following the direc-
tion of the arrow.
For steam installations the filter basket
should be installed horizontally with the
flow following the direction of the arrow.

2
0

7
5

/

4

x

1
4

1
0
5
1
0
0
1
5
0
150 10
Body
Screen
Cover
DATA SHEET
Tag No(s): included in G340
Type No.: 7040
Version: B.3
Filter; DN 20, PN 25 7040000071
4-14 / 23 Language UK
Type:

Stop ball valve, straight

133 BW, full bore

Size:

DN 32
Application:

For air, steam, or oil flow

Material

Body: ASTM A105

End connections: ASTM A105

Technical data:

Min./max. temperature at 30 bar:

- 29C to + 230C

End connections: Butt weld according to

ASME/ANSI B16.25 - XS-80

Pipe size: DN 32

Weight: 4.3 kg
Installation:
Information and caution before installation
of the valve:

Pipe must be free of tension.

Pipe must be flushed to clean the dirt,

burrs calamines, welding residues etc.
which would damage the ball and seat.

The valve must be kept in open position

during installation. Protective plastic
covers must not be removed before the
installation work commences.

At the moment of the shipment the ball

is lubricated with a pure vaseline oil,
which can be easily removed with a sol-
vent, if required.

Ball valves normally have a space be-

tween ball and inside cavity of the body,
which could trap the product, care should
be taken to drain the cavity.
Instruction for welding the valve on the pipe
line:

Tack weld in four points on both end-

connections.

Lift out the centre part to protect the gas-

kets against damage and complete the
welding.

Insert the centre part and ensure easy op-

eration.

4
2
.
2

3
2
.
7
1
.
6
4
.
9
37.5
Detail A
120
End connection
Detail A
Bolt
Center part
85
1
0
8
225
DATA SHEET
Tag No(s): included in G340
Type No.: 6010
Version: A.2
Stop valve, ball, straight, DN 32 87D3066
Language UK 4-15 / 23
Type:

Differential pressure switch.

Size:

Connection, process: G 1/4" -f

Cable: 6 - 13 mm
Application:

The units are pressure-controlled

switches. The pressure controls are suit-
able for use in alarm and regulation sys-
tem.
Material:

Sensor: Brass, CuZn39Pb3

Housing: Messing, CuZn39Pb3

Male electrical plug: PA, Polyamid

Technical data:

Pressure, min. operating: 0 bar

Pressure, max. operating: 4 bar

Measuring range, min. : -1 bar

Measuring range, max. : 6 bar

Switching difference: 0.15 bar

Temperature, operating min.: - 25C

Temperature, operating max.: + 85C

Temperature, min. of medium: - 25C

Temperature, max. of medium : + 120C

Mounting torque: max 25Nm

Weight: approx. 800 g

Electrical specifications:

Male electrical plug: DIN4360-A

Degree of protection: IP65

DATA SHEET
Tag No(s): included in G340
Type No.: 8040
Version: B.1
Differential pressure switch, 0 - 4 Bar 8040000008
4-16 / 23 Language UK
Type:

Stop ball valve, straight

133 BW, full bore

Size:

DN 20
Application:

For air, steam, or oil flow

Material

Body: ASTM A105

End connections: A105

Technical data:

Min./max. temperature at 30 bar:

- 29C to + 230C

End connections: Butt weld according to

ASME/ANSI B16.25 XS-80

Pipe size: DN 20

Weight: 2.3 kg
Installation:
Information and caution before installation
of the valve:

Pipe must be free of tension.

Pipe must be flushed to clean the dirt,

burrs calamines, welding residues etc.
which would damage the ball and seat.

The valve must be kept in open position

during installation. Protective plastic
covers must be removed before the in-
stallation work commences.

At the moment of the shipment the ball

is lubricated with a pure vaseline oil,
which can be easily removed with a sol-
vent, if required.

Ball valves normally have a space be-

tween ball and inside cavity of the body,
which could trap the product, care should
be taken to drain the cavity.
Instruction for welding the valve on the pipe
line:

Tack weld in four points on both end-

connections.

Lift out the centre part to protect the gas-

kets against damage and complete the
welding.

Insert the centre part and ensure easy op-

eration.

2
6
.
7

1
8
.
9
1
.
6
3
.
9
37.5
Detail A
DATA SHEET
Tag No(s): included in G340
Type No.: 6010
Version: A.2
Stop valve, ball, straight, DN 20 87D3064
Language UK 4-17 / 23
100
End connection
Detail A
Bolt
Center part
66
8
0
193
DATA SHEET
Tag No(s): included in G340
Type No.: 6010
Version: A.2
Stop valve, ball, straight, DN 20 87D3064
4-18 / 23 Language UK
Type:

Fuel oil supply pump unit, with filter

Manufacturer type:SPZ 10-R 28

Size:

Connection inlet, nominal: DN 25

Connection outlet, nominal: DN 20

Cable gland:
Pressure rating:

Pressure inlet, nominal: PN 16

Pressure outlet, nominal: PN 40

Connection type:

Connection type: Flange according to

EN
Application:

For handling heavy fuel oil or diesel oil.

Material:

Insert: AlMgSi1

Housing: EN-GJS-400-15

Cover: EN-GJS-400-15

Filter cap: EN-GJS-400-15

Bearing: AlMgSi1

Spindle: 16MnCrS5

Screws: 16MnCrS5

Casing: EN-GJS-400-15

Wire meshing at radial

screen filter: Galvanized steel
Technical data:

Insulation class: F

Pressure, max. supply: 5 barg

Pressure, relief design: 36 barg

Pressure, discharge outlet:33 barg

Temperature max. fuel oil: 150C

Foundation bolts: M 12

Viscosity: 3 cSt
Oil capacity: 344 l/h
NPSH: 2.60 mWC

Viscosity at 380 cSt:

Oil capacity: 702 l/h
NPSH: 4.00 mWC

Weight: 106 kg
Casing
Bearing Screws Spindle Wire meshing at radial
screen filter
Cover
Filter cap Housing Insert
Electrical specification:

Power supply: 3 x 440V

Frequency: 60hz

Degree of protection: IP54

DATA SHEET
Tag No(s): G147
Type No.: 9294
Version: B.1
Fuel oil supply pump unit, with filter, 10-R 28 9294002051
Language UK 4-19 / 23
Dimension:

L: 721

L1: 110

L2: 436

L3: 456

W: 210

W1: 85

H:535

H1: 365

H2: 284

H3: 140
Installation:

Theaggregates are provided for horizon-

tal installation or wall mounting. For
safety purposes, the arrangement with
motor downwards is not admissible
Connections / flanges:

Counter flanges (welding neck) accord-

ing to EN. Bolts and gaskets will be in-
cluded in the supply.
L1 L2
L
L3
H
3
H
2
H
1
H
W W
1
DATA SHEET
Tag No(s): G147
Type No.: 9294
Version: B.1
Fuel oil supply pump unit, with filter, 10-R 28 9294002051
4-20 / 23 Language UK
Type:

Remote start/stop box

Application:

For start/operation and stop of fuel oil

pumps
Material:

House: Polycarbonate

Colour: Grey
Technical data:

Nominal operating condition:

U = 600 V and I = 1.2 A or
U = 240 V and I = 3 A or
U = 120 V and I = 6 A

Protection: IP 65

Temperature: -25C to +70C

83
1
4
5
1
0
5
1
2
3
85
120
Cable glands M 32 (PG 29)
Stop
105
7
0
5.8
5.8
Fuel oil pumps
1 2
1
7
7
Start/operation
incl. lamp function
DATA SHEET
Tag No(s): G224
Type No.: 8001
Version: B.1
Remote start/stop box 8001000005
Language UK 4-21 / 23
Counter flange
1 --- NO TITLE ---
COUNTER FLANGE K16_004096#C.1
Language UK 4-23 / 23
Table of contents
Mission OC control panel drawing
Description Document ID Page
.
Drawings for boiler control panel................................ .................................. 5-2
Set point list for OC panels......................................... .................................. 5-60
TABLE OF CONTENTS
Language UK 5-1 / 63
Drawings for boiler control panel
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-2 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-3 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-4 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-5 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-6 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-7 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-8 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-9 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-10 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-11 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-12 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-13 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-14 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-15 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-16 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-17 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-18 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-19 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-20 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-21 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-22 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-23 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-24 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-25 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-26 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-27 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-28 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-29 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-30 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-31 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-32 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-33 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-34 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-35 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-36 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-37 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-38 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-39 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-40 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-41 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-42 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-43 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-44 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-45 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-46 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-47 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-48 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-49 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-50 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-51 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-52 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-53 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-54 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-55 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-56 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-57 / 63
DRAWINGS FOR BOILER CONTROL PANEL A.1
5-58 / 63 Language UK
DRAWINGS FOR BOILER CONTROL PANEL A.1
Language UK 5-59 / 63
Set point list for OC panels
SET POINT LIST FOR OC PANELS A.1
5-60 / 63 Language UK
List of Indicators and Set Points for ON 103631
Item Units Range Default Type ITEM NO IN DRAWING Element Bnr Physical Remarks
Set point 1) Steam/water P/I diagram Terminal Trip Location
2) Oil flow diagram No. in
3) Burner drawing: wiring
4) Wiring diagram: 101X03:056946 diagram
1 2 3 4
Safety Valve BAR 10.0 25.912 Mechanical
High Steam Pressure Switch BAR 1-10 9.0 RT30 C35 33S2F X2:222/223 X Boiler
High Steam Pressure ME. Slow d. BAR 1-10 9.5 RT30 Boiler Signal to ECR only
Steam Pressure Transmitter Boiler BAR 0-10 MBS 5100 C48 30A1F X2:10/11 Boiler
High steam pressure BAR 0-10 9.0 - - - - X
Low steam pressure BAR 0-10 5 - - - -
Start/Stop Pressure BAR 0-10 7.2-8.0 - - - -
Steam pressure set point BAR 0-10 7 - - -
Steam pressure transmitter Common BAR 0-10 MBS 5100 50A5F
High steam pressure BAR 0-10 9.0 - - -
Steam dump set point BAR 0-10 8.5 - - -
Low steam pressure BAR 0-10 4 - - -
Water Level Transmitter (4-20mA) mA 4-20 GESTRA /CLT W33 30A11F X1:14/15/16/17 Boiler
Too high water level mm WG 20 +180 - - - X
High Water Level mm WG 18 +150 - - - Boiler
Normal Water Level mm WG 0 - - -
Stand by feed water pump mm WG - - -
Low Water Level mm WG 6 -135 - - - Boiler
Too Low Water Level 1 mm WG 4 -180 GESTRA / Controller 15A1A component X Boiler
Oil Pressure Transmitter Burner (4-20mA) BAR 0-10 MBS 5100 F225 30A14F X1:18/19 Boiler
High oil pressure BAR 0-10 2.3 - - - - X
Low oil pressure BAR 0-10 0.8 - - - - X
Oil pressure set point BAR 0-10 1.8 - - - -
Stand by oil pump start BAR 0-10 1.2 - - - -
Oil temperature Transmitter Burner (4-20mA)
o
C 0-150 F212 30A3F X1:12/13 Boiler
High oil temperature
o
C 0-150 100 - - HFO
Low oil temperature
o
C 0-150 65 - - HFO
Temp. Control Switch Heat Cable
o
C 30-90 85 RAM 42.001 43S2D X1: 44-45 Burner
Low Com. Air Pressure Switch mBAR 2,5-50 5 GW 50 A4 R3 14S6B X1: 38-39 X Burner
Burner Swing Out / Burner Open Limit Sw. F224 33S3F X1: 32-33 X Panel
Flame Failure 1 RAR7/LAE10 F32 40P5D X Bnr. + Panel Cut Off Oil Supply
Flame Failure 2 RAR7/LAE10 F33 40P11D X1: 40-41 Bnr. + Panel Cut Off Oil Supply
Temperature transmitter in preheater (for reg.)
o
C PT100 F222 31A3E
Oil temperature set point (380cSt@50
o
C)
o
C 0-150 125 - -
High oil pressure in return line BAR F214
Oil Servo Motor Limit Switches: F184 See sheet 35 in wiring
Max. Position Degr. 0-90 90 To be set during commisioning - Burner diagram and burner
Oil fired boiler / Burner
Page 1 of 4
SET POINT LIST FOR OC PANELS A.1
Language UK 5-61 / 63
List of Indicators and Set Points for ON 103631
Item Units Range Default Type ITEM NO IN DRAWING Element Bnr Physical Remarks
Set point 1) Steam/water P/I diagram Terminal Trip Location
2) Oil flow diagram No. in
3) Burner drawing: wiring
4) Wiring diagram: 101X03:056946 diagram
1 2 3 4
Min. Position Degr. 0-90 0 To be set during commisioning - Burner instruction manual
Air Servo Motor Limit Switches: F7 See sheet 36 in wiring
Max. Position Degr. 0-90 90 To be set during commisioning - Burner diagram and burner
Min. Position Degr. 0-90 0 To be set during commisioning - Burner instruction manual
Thermal Overload Relays:
Burner Motor A 6.0-10 7.6 GV2-P14 07F6B X Panel
Oil transfer pump 1 A 2.5-4.0 3.4 GV2-P08 07F2B Panel
Oil transfer pump 2 A 2.5-4.0 3.4 GV2-P08 07F4B Panel
Preheater A 6-10 9.6 GV2-P14 07F10B Panel
Timers:
Delay Too Low Water Level 1 Sec. 3-60 15 GESTRA controller 15A1A Panel
Delay Low Combustion Air Press. Sec. 3-60 15 Brodersen Panel
Delay St.By Oil Transfer Pump Sec. 10 Software Panel
Fuel oil Flow meter P/liter 100 31A12F
Power Failure X Panel
High oil content MCU200 20A8D
High Salinity ppm 0-1000 8 SL700 20A3D
Hotwell too low stop feed water pumps Limit Sw. 53S11E
Feed water pump (oil fired) stby start BAR 1-10 3 RT30 53S12E
General signals
Page 2 of 4
SET POINT LIST FOR OC PANELS A.1
5-62 / 63 Language UK
Alarm, Shutdown and Modbus
DATE: 09/12/2009 Modbus address list
Burnertypes: 1xKBO-E/R13M
VER.: 6.14 Please Reserve Adress 40000 - 40999 to AI Modbus
Boiler: Mission OC
Modbus Addr. Word no. Type Description
Function description
40525 AI Command operation mode 0 = stopped; 1 = manual; 2= auto;
40526 AI Command start
0 = no command; 1 = start; 2 = stop
(only possible in manual mode)
40527 AI Command stop
0 = no command; 1 = start; 2 = stop
(only possible in manual mode)
40523 AI Boiler pressure manuel increase
40524 AI Boiler pressure manuel decrease
40522.12
AI Unit of measurement (pressure values only)
0 = 1/10 bar; 1 = 1/10 kg/cm; 2 =
1/100 Mpa
40600
AI
Status feedback 0 = STOPPED; 1 = SHUTDOWN; 2
= READY; 3 = STARTING; 4 =
PURGE; 5 = IGNITION
POSITION; 6 = IGNITION; 7 =
SAFETY TIME; 8 = FLAME
STABLE; 9 = LOW FIRING; 10 =
RISING; 11 = MOD FREE; 12 =
STEAM PURGE POSITION; 13 =
STEAM PURGE 1; 14 = STEAM
PURGE 2; 15 = POST PURGE
40020 AI Burner Load %
40010
AI Steam pressure (boiler) Unit of measurement - See word 11
40022 AI Water level boiler mmWC
40109 AI Temperature boiler uptake 1/10 C
40077
AI Fuel Oil pressure Unit of measurement - See word 11
40063 AI Fuel Oil temperature 1/10 C
40508.02 DO Fuel oil pump 1, start/stop 0 = Stopped; 1 = Running
40508.03 DO Fuel oil pump 2, start/stop 0 = Stopped; 1 = Running
40509.01 DO Chemical dosing station 1 0 = Stopped; 1 = Running
40515.00 FUEL PUMP 1 NO FEEDBACK
40515.01 FUEL PUMP 2 NO FEEDBACK
40515.08 OIL CONTENT HIGH
40515.09 WAR_SALINITY_HIGH
40515.12 HIGH GAS TEMP AT EGB
40515.14 not used
40515.15 BOILER PRESSURE LOW
40516.01 WATER LEVEL HIGH
40516.02 WATER LEVEL LOW
40516.03 FUEL OIL PRESSURE LOW
40516.04 FUEL OIL TEMPERATURE LOW
Digital outputs
Alarms
Operation
Analog inputs
SET POINT LIST FOR OC PANELS A.1
Language UK 5-63 / 63
Alarm, Shutdown and Modbus
DATE: 09/12/2009 Modbus address list
Burnertypes: 1xKBO-E/R13M
VER.: 6.14 Please Reserve Adress 40000 - 40999 to AI Modbus
Boiler: Mission OC
Modbus Addr. Word no. Type Description
Function description
40516.08 FUEL PUMP 1 OVERLOAD
40516.09 FUEL PUMP 2 OVERLOAD
40517.00 ST. BY FUEL PUMP STARTED
40517.05 EXTERN STOP
40517.06 BOILER PRESS. HIGH
40517.08 FUEL OIL TEMPERATUREHIGH
40518.10 HOTWELL LOW FEED PUMPS STOPPED
40519.00 HIGH DP HFO SUCTION FILTER
40697.01 BOILER PRESSURE Manual
40697.04 WATER LEVEL MANUAL
40697.05 OIL FLOW MANUAL
40510.01 HIGH STEAM PRESSURE SWITCH
40510.02 TOO LOW WATER LEVEL SWITCH
40510.03 BURNER NOT READY
40510.05 FLAME OUT
40510.07 NO FUEL PUMPS AVAILABLE
40510.09 POWER PANEL1 OFFLINE
40510.10 BURNER SERVO ERROR
40510.12 IGNITER INSERTED
40510.14 START SEQUENCE MAX TIME EXPIRED
40510.15 PHOTO CELL FAILURE
40511.00 QUICK CLOSING VALVE NOT OPEN
40511.02 HIGH TEMPERATURE UPTAKE
40511.05 BURNER SWING OUT
40511.11 WATER LEVEL HIGH
40511.12 WATER LEVEL LOW
40511.13 BOILER PRESSURE HIGH
40512.01 LOW COMB AIR PRESS SWITCH
40512.02 BURNER MOTOR OVERLOAD
40512.03 LOW OIL TEMP. NOZZLE SUPPLY SWITCH
40512.04 SALINITY HIGH
40512.05 TEMP. UPTAKE HIGH
40512.06 IGNITER NOT INSERTED
40513.09 OIL CONTENT HIGH
40513.10 HIGH OIL PRESSURE ON BURNER
40513.12 HIGH OIL TEMP SW IN PREHEATER
40513.13 FUEL OIL PRESSURE HIGH
40514.01 FLAME OUT SCANNER 2
Shutdown
Table of contents
Spare part
Description Document ID Page
.
Spareparts for MISSIONOC.................................... .................................. 6-2
Spareparts for Pressure jet burner - KBO...................... .................................. 6-3
TABLE OF CONTENTS
Language UK 6-1 / 3
Spareparts for MISSIONOC
Boiler plant:...................................................................................................................1 x MISSION OC
Request No.:...................................................................................................................................... 103631
Configuration No.:.......................................................................................................................................1
Hull No./Nos.:..........................................................................................................................S1396, S1397
Project No./Nos:..................................................................................................103631-01-2, 103631-02-2
The spare parts supplied in the scope of delivery for includedMISSIONOC boilers are listed in the table
below.
1 Spare parts
Tag No. Qty. Application Spare part N o.
Spare parts for the b oiler
S-C1-3 1 Spring for safety valve, OD32 8580000001
S-C17-1/S-C18-1 4 Water level glass, type A, size 16 8590000020
S-C17-2/S-C18-2 6 Gasket for water gauge stud 2163719
S-C-1 4 Gasket for manhole 2158320
S-C-2 16 Gasket for handhole 2158609
S-C-3 4 Plug f. pinelement 6494971
S-C-7(*) 12 Tube plug 6494104
S-C-8 1 Plistix 14 25 kg 2118236
S-C-9(*) 1 Spare part box.w.hinged lid and brac. For padlock 6499402
S-C-10(*) 1 Pad lock 50mm 4234331
S-C33-1 1 Pressure gauge 100 6632973
S-C-17 1 Inspection mirror 8500000362
Spare part s for commissioning
S-C-5 2 Gasket for manhole 2158320
S-C-6 8 Gasket for handhole 2158609
SPAREPARTS FOR MISSIONOC A.1
6-2 / 3 Language UK
Spareparts for Pressure jet burner - KBO
Boiler plant:...................................................................................................................1 x MISSION OC
Request No.:...................................................................................................................................... 103631
Configuration No.:.......................................................................................................................................1
Hull No./Nos.:..........................................................................................................................S1396, S1397
Project No./Nos.:.................................................................................................103631-01-2, 103631-02-2
Date:......................................................................................................................................02 March 2009
The spare parts included in the scope of delivery of a standard Modulating pressure jet burner are listed in
the table below.
1 Spare parts
Tag No. Qty. Application Spare part N o.
Spare parts for the burner
S-F1-1 1 Pressure gauge 8050000054
S-F1-3 1 Nozzle for burner 8610000138
S-F1-5 1 Ignition electrode 8620000084
S-F1-8 1 Photo cell 6310720
S-F1-112 1 Nozzle Head repair set 8500000775
Spare parts for the oil pumps
S-G147-1 2 O-ring for Filter cover 3520000011
Commissioning parts for the oil pumps
CS-G147-9 2 O-ring for mechanical seal inner 3520000050
CS-G147-10 2 O-ring for mechanical seal outer 3520000048
Tools
F121 1 Hooking device for oil burner 8500000780
SPAREPARTS FOR PRESSURE JET BURNER - KBO A.1
Language UK 6-3 / 3
Table of contents
Descriptions
Description Document ID Page
.
MISSION OC boiler............................................... SD9210_02................. 7-2
Boiler mountings....................................................... SD9220_17................. 7-6
Water level control.................................................... SD9230_12................. 7-8
Gauge board............................................................. SD9240_14................. 7-9
TABLE OF CONTENTS
Language UK 7-1 / 9
MISSION OC boiler
1 Description
The MISSION OC boiler is a combined oil and exhaust gas fired vertical marine
boiler, insulated and assembled as a unit with the boiler mountings mounted on the
boiler body.
The boiler mountings are mainly mounted on top of the boiler body in order to allow
a simple connection to the piping systems on board the ship.
The burner is ready for mounting in the furnace and connection of pre-marked electric
wiring.
The control system supplied with the MISSION OC boiler unit provides fully au-
tomatic operation of the boiler and burner.
1.1 Boiler pressure part
The pressure part of the MISSION OC boiler is shown in Figure 1. The combined
oil fired and exhaust gas fired boiler is designed as a vertical boiler with a cylindrical
shell surrounding the oil fired and the exhaust gas fired sections. The oil fired section
comprises the cylindrical furnace, the steam space, and the convection section con-
sisting of pin tube elements. The exhaust gas fired section comprises the stay tubes and
smoke tubes.
The pressure part is made of mild carbon steel with elevated temperature properties.
This means that stress concentrations in corner welding are minimised by the design
of the cylindrical shell with the flat endplates of equal thickness.
The cylindrical shell with the two flat endplates welded on is supported by the stay
tubes, the pin-tube elements, and the furnace. Also the steam drum is a cylindrical
vessel welded on the top plate and upper tube plate. The drum acts as a dividing plate
to the exhaust gas fired section. This unique design ensures that no supports are re-
quired.
The pin tube elements consist of an outer tube enclosing the pin tube. The pin tube is
a plain seamless steel tube provided with an inlet pipe at the bottom and an outlet pipe
at the top. A large number of pins are welded around the outside of the tube creating
an extended heating surface. This extended heating surface transfers heat from the flue
gas to the steam/water mixture in the pin tube.
MISSION OC BOILER SD9210_02#A.2
7-2 / 9 Language UK
The tubes in the exhaust gas fired section consist of a small number of stay tubes and
a large number of smoke tubes. The stay tubes with an increased diameter act as support
for the boiler. Both types are welded onto the endplates.
The furnace is cylindrical with two flat plates. The bottom steel plate is protected from
radiation of heat by refractory. Furthermore, the furnace bottom is provided with a
socket for drain of washing water.
For inside inspection, the MISSION OC boiler is arranged with both hand holes and
manholes. Two manholes are arranged on the boiler shell for convenient access both
into the oil fired section and into the exhaust gas fired section. For visual check of the
smoke tubes, a number of hand holes are arranged in a suitable distance at the bottom
of the boiler drum. For inspection of the flue gas side, inspection doors are arranged
on the flue gas inlet and outlet chamber.
The boiler mountings such as safety valves, steam outlet valve, water level electrodes,
etc. are mainly mounted on top of the boiler body in order to allow simple connection
to the piping system on board the ship. Furthermore, inlet and outlet boxes are included
in the delivery.
Boilers with a diameter up to 3,000 mm are prepared for tack welding along the boiler
shell. For boilers with a diameter above 3,000 mm, the boiler foundation is arranged
as a flanged type which reduces the thermal mechanical stresses to a minimum during
operation. The counter flange is included and ready for welding to the deck. In both
cases, vent holes in suitable numbers are arranged to ensure the circulation of air below
the boiler.
The boiler is prepared for mounting of a compact silencer to suit any type of engine.
The optimal silencer dimensions suitable for each installation should be calculated on
basis of the data for the engine, exhaust gas system, and level of sound absorption.
MISSION OC BOILER SD9210_02#A.2
Language UK 7-3 / 9
Principle drawing of the MISSION OC boiler
Inspection door
Inspection door
Fire hole
Pin-tube
Pin-tube
Smoke/stay tubes
Smoke tubes Stay tubes Upper tube plate
Steam drum
End plate
(top plate)
Manhole
Hand hole
End plate
Foundation
Refractory
Furnace
Boiler drum
Outer tube
Figure 1 sd9210_02_oc1x0063660en.wmf
1.2 Heat transfer and water circulation
Oil ignition and combustion take place in the furnace. The produced heat is transferred
mainly by radiation from the flame to the furnace shell. Leaving the furnace, the flue
gases enter the vertical uptakes where heat is transferred to the pin-tube elements
mainly by convection.
In the exhaust gas fired section, heat from the engine exhaust gas is transferred to the
water side by convection.
On the water side, the heat is transferred by evaporation of the saturated water adjacent
to the furnace shell or tube wall (smoke- and pin tubes) where steam bubbles are
formed. As the steam bubbles have a much lower specific density than the water, they
will rise rapidly to the steam space where water and steam are separated.
The natural circulation in the pin-tube element occurs because the density of water is
higher than the density of steam. The density of the water outside the pin-tube element
is higher than the steam/water mixture inside the pin tube element. The difference in
the static pressure at the bottom connection to the pin tube creates the driving force for
the circulation. The steam/water mixture is discharged into the steam space where the
heavier water particles separate from the steam and flow back into the water.
The oil fired section of the boiler is designed so that approximately half of the steam
is generated in the pin-tube elements and the rest by radiation in the furnace.
MISSION OC BOILER SD9210_02#A.2
7-4 / 9 Language UK
1.3 Steam space
The steam space in the oil fired boiler is designed to absorb the shrink and swell vol-
umes. It is advisable, however, to avoid sudden and large load variations as this might
create instability in the steam system, and cause level alarms.
MISSION OC BOILER SD9210_02#A.2
Language UK 7-5 / 9
Boiler mountings
1 Mountings
The following is a brief description of the most important items of the boiler mountings.
The components mentioned in this section are referring to the general arrangement
drawing of the boiler.
Safety valves
Two safety valves are fitted to the pressure vessel of the boiler. They are installed for
security reasons, and designed to prevent the boiler pressure from rising above the
design value.
The safety valves must be supplied with waste steam pipes and either expansion de-
vices, or bellows.
Main steam valve
The main steam valve is a shut off/non-return valve. When closed, it isolates the boiler
from the main steam line. When open, it prevents steam from flowing backwards into
the boiler.
Feed water valve / feed water valve (sdnr)
Two feed water lines are provided in the boiler. Each line is fitted with a shut-off valve
and a non-return valve.
The shut-off valve in the primary line must be open when the boiler is in operation.
This also applies if only the exhaust gas fired section is in operation.
The shut-off valves should be closed when the boiler is not in use.
Water level gauges
Two local water level gauges are connected to the front of the boiler, each gauge being
provided with two shut-off valves and a drain valve.
The shut-off valves, fitted at the top and bottom of the sight glass, have a quick-self
closing mechanism to be used in case of broken glass.
The pipes from the drain cocks on the water level gauge must lead to an open drain,
visible for inspection.
BOILER MOUNTINGS SD9220_17#B.1
7-6 / 9 Language UK
Blow-down valve / blow-down valve (sdnr)
Two blow-down valves are mounted at the bottom of the boiler body. If connected to
a separate drainage system the valves are of the ball type. When connected to a common
drainage system two valves are provided in each group, one shut-off valve and one
shut-off/non-return valve. The shut-off function is for security and the non-return
function prevents steam/water from flowing into an empty boiler by mistake.
Air valve
The air/ventilation valve located on top of the boiler is a shut-off valve. It is normally
closed except when the boiler is being filled or completely drained. The end of the
drain pipe from the air valve must be visible in order to determine when air or steam
is coming out.
Scum valve
The scum valve is mounted at the top of the boiler body. In the event of scum in the
boiler, this scum can be blown off from the water surface by opening this valve. If
connected to a separate drainage system the valve is of the ball type. When connected
to a common drainage system two valves are provided, one shut-off valve and one
shut-off/non-return valve.
Sample valve
A sample valve is installed enabling connection to a sample cooler for taking test
samples to perform boiler water analyses.
Manhole
Two manholes are arranged on the boiler shell which allow inside inspection of the oil
fired section and the exhaust gas fired section.
Hand hole
A number of hand holes are distributed regularly around the circumference of the boiler
and at the bottom of the boiler drum for visual check and cleaning of the smoke tubes.
Inspection hole
A small inspection hole is provided in the furnace wall to enable inspection of the
burner flame. A proportion of the air supply is bled off from the burner fan to cool the
window of the inspection hole, and prevent soot deposits.
Inspection door
The boiler is provided with two inspection doors to enable inspection of the flue gas
inlet and outlet chambers.
Access to the furnace is gained by swinging out the burner unit.
Drain for furnace
The furnace bottom is provided with a socket for drain of the washing water.
BOILER MOUNTINGS SD9220_17#B.1
Language UK 7-7 / 9
Water level control
1 Description
The water level control is a modulating system at this type of boiler. The system is
illustrated in Figure 1. The system consists of one independent safety device electrode
for too low water level shut down and burner stop. For measuring and control of the
water level, one capacitance level electrode is provided, and it is used to give water
level alarms/shut downs and control of the regulating feed water valve.
Water level control system
Boiler
Feed water pumps
Control
system
(panel)
Feed water
valves
LW
NW
HW
Water level control system
Flange
Electrode stand
Vent hole
Compact system
(level transmitter
and level electrode)
Safety device
Protection tube
Regulating feed water valve
Instrument air
Figure 1 sd9230_12_ges_1_x0063950en.wmf
WATER LEVEL CONTROL SD9230_12#A.2
7-8 / 9 Language UK
Gauge board
1 Description
The function of the gauge board is to control the burner and to give alarm and shut
down for low and high steam pressure.

A pressure gauge is fitted for analogous reading of the actual steam pressure in the
boiler.

A pressure switch "high steam pressure" gives shut down and burner cut-off when
the steam pressure rises above the pre-adjusted set point. The pressure switch locks
the burner in stop mode. Operation of the burner is only possible when the steam
pressure falls below the differential set point of the pressure switch and the shut
down function is reset.

A pressure transmitter connected directly on the boiler converts the actual steam
pressure of the boiler into corresponding electric signals. The signals are used to
give alarms for low/high steam pressure and shut down/burner cut-off for high
steam pressure. The signals also control start/stop and modulation set point of the
burner. Furthermore, the pressure transmitter can be used for remote steam pres-
sure indication.
GAUGE BOARD SD9240_14#A.2
Language UK 7-9 / 9
Table of contents
Operation and maintenance
Description Document ID Page
.
Start/stop of the boiler................................................ OM9210_02............... 8-2
Boiler maintenance.................................................... OM9210_09............... 8-8
Boiling out................................................................ OM9210_11............... 8-12
Manhole gaskets and hand hole gaskets........................ OM9010_39............... 8-14
Cleaning pin-tube elements......................................... OM9210_12............... 8-16
Cleaning smoke tubes................................................ OM9210_14............... 8-19
Preservation.............................................................. OM9210_13............... 8-22
Boiler repair - pin-tube element................................... OM9210_20............... 8-24
Plugging of smoke tubes............................................. OM9210_22............... 8-26
Boiler repair - refractory............................................. OM9210_25............... 8-28
Lighting-up curve...................................................... OM9210_31............... 8-32
TABLE OF CONTENTS
Language UK 8-1 / 32
Start/stop of the boiler
1 General
The following chapters of the instruction manual describe the operation and mainte-
nance of the pressure part. As this is only a part of the complete boiler plant, it is
important to study the remaining chapters in this manual very thoroughly. It is espe-
cially important that the operator of the boiler plant becomes familiar with the operation
instructions of the burner and the control panel.
Important: To ensure a safe and reliable operation of the boiler plant, all oper-
ation and/or maintenance of the boiler should be carried out only by
skilled personnel.
2 Boiler operation modes
The MISSION OC (-TCi) boiler is a combined oil fired and exhaust gas fired boiler.
The combination between an oil fired section and an exhaust gas fired section makes
it possible to operate the boiler in different modes. The different modes are:
- Operation only on the oil fired section
- Operation only on the exhaust gas fired section
- Operation on both the oil fired and exhaust gas fired section
2.1 Boiler operation modes
2.1.1 Combined operation mode
In normal operation, the boiler operates as a combined oil fired and exhaust gas fired
boiler. The steam production is controlled by the amount of exhaust gas from the engine
and the gauge board which controls the oil burner. If the engine produces an insufficient
amount of exhaust gas to maintain the steam pressure, the gauge board gives a signal
to initiate start of the oil burner. The oil burner operates as long as the steam pressure
does not exceed the set point for burner stop. If the steam pressure increases above this
set point, the gauge board gives a signal to initiate stop of the oil burner.
The combined operation mode always requires that the water level is within the normal
limits of the boiler.
START/STOP OF THE BOILER OM9210_02#C.2
8-2 / 32 Language UK
2.1.2 Oil fired operation mode
If the engine is stopped, the only heat source is the oil burner. When the steam pressure
is below the set point for start of the burner, it will be in operation. By means of signals
from the gauge board, the control system aims to maintain the desired steam pressure
regardless of the steam output. The oil burner operates as long as the steam pressure
does not exceed the set point for burner stop.
The oil fired operation mode always requires that the water level is within the normal
limits of the boiler.
2.1.3 Exhaust gas fired operation mode
When the exhaust gas flow through the boiler, produced by the main engine, is suffi-
cient to maintain the steam pressure, the burner will not be in operation. If the exhaust
gas flow is above the required flow to maintain the steam pressure at a given steam
output, the pressure increases. At a pre-selected set point the steam dump equipment,
located elsewhere in the steam system, opens the dump valve and regulates the steam
line pressure. If, however, the steam dump equipment is not operational the boiler
pressure may rise above the set point for high steam pressure shut down and even up
to the maximum allowable working pressure. At this point, the safety valves open and
ensure any further increase of the steam pressure. Please note that some classification
societies require a separate switch which reduces the engine load before the maximum
allowable working pressure is reached.
Note: If the high steam pressure shut down has been activated, the oil burner will
not be operational until the shut down function can be and is reset in the
control system.
The construction of the MISSION OC (-TCi) boiler permits operation with low water
level and even without water in exhaust gas mode with the full exhaust gas flow through
the smoke tubes. In the latter case the boiler must be operated depressurised.
Please note that operation without water should be considered as an emergency oper-
ation mode and should only be used if no other operation alternatives are present. The
most effectual operation of the boiler is with the water level within the normal limits
as this creates the most stable operating conditions
Warning: Before start of the boiler it must be drained and the manhole cover
should be dismounted to ensure that it is operated completely depres-
surised. Please note that the temperature inside the boiler must not
exceed 400C.
If the boiler operates without water, it will gradually be heated to the same temperature
as the exhaust gas. It is therefore important to allow the boiler to cool before refilling
it with feed water. If this is not possible, the feed water should be pre-heated, and the
refilling should be carried out very carefully.
START/STOP OF THE BOILER OM9210_02#C.2
Language UK 8-3 / 32
Note: If the too low water level shut down has been activated, the oil burner will
not be operational until the shut down function can be and is reset in the
control system.
Furthermore, operation of the boiler without water eventually dries out the gaskets,
and a replacement of the gaskets is necessary.
3 Start-up
When the boiler is commissioned or started during normal operation, it is preferable
to lighten-up the boiler with the oil burner as the heat source. This is because the oil
burner load is much easier to control than the exhaust gas amount from the engine.
It is possible, however, to start the boiler when exhaust gas is used as heat source. This
requires more attention with regard to water level control, pressurising pipes, etc.
When the boiler is started and lightened-up by means of the exhaust gas flow, it is
important to reduce the heating-up rate in order not to cause stresses in the boiler.
This can be done by reducing the engine load to fit the appropriate heating-up rate or
by by-passing some of the exhaust gas flow if a by-pass system is provided.
3.1 Before start-up
When the boiler is started, the lighten-up rate of the boiler must not be accelerated too
much as this might cause an unnecessary overstrain of the boiler material by quick and
uneven temperature rises. It might be necessary to perform a number of start/stop
sequences to reduce the lighten-up rate.
Attention: At the commissioning start-up of the boiler and after any repair work
of the refractory, it is very important to further reduce the lighting-
up rate. This is because the new refractory still contains a small
amount of water. When heated the water vaporises and expands
which might cause fissures and cracks in the refractory. The burner
must therefore only be operated at minimum load and in intervals of
1-2 minutes for the first hours. Between each operation interval the
burner should remain stopped for approximately 8-10 minutes.
Before start-up of the boiler plant, some general work and check procedures must be
considered.
Step A: Check that all pipelines are ready for operation and that possible blind
flanges used during pressure tests have been removed.
Step B: Check that the main steam valve, scum valve, and blow-down valves are
closed.
START/STOP OF THE BOILER OM9210_02#C.2
8-4 / 32 Language UK
Step C: Open the feed water valves and the air valve. Fill the boiler with feed water
to approximately 50 mm below normal water level. The water level rises
due to expansion when the boiler is heated. If the temperature difference
between the boiler and feed water exceeds approximately 50C, the boiler
must be filled very slowly.
Note: When filling a pressure less boiler, the shut-off valve after the feed water
pump must be throttled. Otherwise the pump motor will be overloaded.
Step D: Check the water level in the water level gauges. Check frequently during the
complete start-up. The water level gauges should be blown down several
times to ensure a correct indication.
Step E: Check that the water level control system is connected and operational.
Step F: Check the oil system and start the fuel oil supply pump. Pre-heat the fuel oil
if the burner should operate on heavy fuel oil.
Step G: Check the burner and the safety functions according to the separate instruc-
tion.
3.2 Start and pressure rise
The following work procedures must be followed during start-up of the boiler.
3.2.1 Start and pressure rise by means of the oil burner:
Step A: Check that the gauge board valve and pressure gauge valves are opened.
Step B: Check that the air valve is open if the boiler pressure is below 1.0 barg.
Step C: Start the burner on manual control and on low load. Check that the water
level does not rise too high during the pressure rising period.
Step D: Drain via the blow down valves if the water level is too high.
Step E: If the air valve was opened close it when only steam blows out. A pressure
reading should be indicated on the boiler pressure gauge before the air valve
is closed.
Step F: Check that any connected remote indicators are working correctly.
Step G: Re-tighten all covers such as manholes, hand holes, inspection doors, flang-
es, etc. during the pressure rising period. If required, check all flange joints
on the plant.
Step H: Change to automatic control of the burner when the boiler pressure is 0.5
barg lower than the working pressure of the boiler.
Step I: Open the main steam valve slowly to heat-up and pressurise the steam sys-
tem.
Step J: Open the valves to the steam consumers carefully in order to avoid water
chocks.
Step K: When the boiler is in normal operation, check that the water level control
system and the gauge board functions are fully operational.
3.2.2 Start and pressure rise by means of the exhaust gas section:
The following start-up procedure is described on the assumption that the engine is in
operation and the exhaust gas flow is sufficiently high to lighten-up the boiler.
Step A: Check that the gauge board valve and pressure gauge valves are opened.
Step B: Check that the air valve is open if the boiler pressure is below 1.0 barg.
START/STOP OF THE BOILER OM9210_02#C.2
Language UK 8-5 / 32
Step C: Check the water level and fill the boiler with evaporated water as described
previously, if necessary.
Step D: Drain via the blow-down valve if the water level is too high.
Step E: If the air valve was opened close it when only steam blows out. A pressure
reading should be indicated on the boiler pressure gauge before the air valve
is closed.
Step F: Check that any connected remote indicators are working correctly.
Step G: Re-tighten all covers such as manholes, hand holes, inspection doors, flang-
es, etc. during the pressure rising period. If required, check all flange joints
on the plant.
Step H: When the boiler pressure is approximately 1.5-2.0 barg and if the steam
system is not pressurised, open the main steam valve slowly to heat-up and
pressurise the steam system.
Step I: Open manually the steam dump valve somewhat to create an increased water
replacement in the boiler.
Step J: When the normal working pressure is reached, set the steam dump valve to
automatic mode and open the valves to the steam consumers carefully in
order to avoid water chocks.
Step K: When the boiler is in normal operation, check that the water level control
system and the gauge board functions are fully operational.
3.2.3 Commissioning notes
When an accumulation test of the safety valves is performed the water level inside the
boiler might increase and cause high level alarm. This is due to an increased water
temperature and acorresponding larger water volume. The water surface also becomes
more unstable during the accumulation test.
After 3-4 weeks in operation, mud and deposits in the piping system may have accu-
mulated in the boiler water. This may cause level variations which disturb the steam
generation, and it is therefore recommended to blow down the boiler. It should then
be inspected, cleaned, and refilled with boiler water.
4 Boiler stop
4.1 Normal boiler shut down
If necessary, the boiler can be shut down at any load without special preparations.
Note: When the boiler is stopped, sudden temperature and pressure drops should
be avoided as they might expose mountings, pipe lines, and the boiler plant
to inadmissible temperature gradients.
If the engine is in operation and must remain in operation, it is not possible to stop the
boiler unless the exhaust gas system is provided with a by-pass system. When the
engine is stopped and the boiler should be stopped, the following work procedures
should be carried out:
START/STOP OF THE BOILER OM9210_02#C.2
8-6 / 32 Language UK
Step A: When minimum load is obtained, stop the burner.
Step B: Keep the water level at normal level until the boiler stops producing steam.
Stop the feed water pump and close the feed water valves.
Step C: Close the main steam valve.
4.2 Emergency shut down
The boiler must be taken out of service immediately if:

parts of the heating surface have been glowing or the boiler shows recognisable
deformations. The supervising authorities must be informed, and the boiler must
not be used until approval from these authorities is available

a substantial loss of water is noted

the feed water system is unable to provide the necessary amount of feed water, e.g.
due to failure of parts

the safety valve cannot function

sudden cracks or damage are noted in the refractory, and if steam or moisture is
coming out of the refractory

oil in the feed water is detected

too high salinity level is detected

If an emergency shut down must be carried out, the fuel supply should be stopped. The
main steam valve should be closed gradually, and the boiler must be cooled. The safety
valves must not be operated. Parallel working boilers should be disconnected at once.
4.3 Stop for repair or inspection
The following describes the measures to be taken when the boiler is shut down for
repair or inspection.
Step A: Clean the boiler from soot with water.
Step B: Operate the burner for at least 15 minutes after the soot removal to dry out
the remaining water.
Step C: Stop the boiler as mentioned previously.
Step D: Check the furnaceand smoke tubes, for the oil fired as well as exhaust gas
part, with regard to cleanliness.
Step E: Empty the boiler from water and clean it. Check if lime stone appears.
Step F: Check and clean the outer fittings. Change gaskets where required.
Step G: Clean the feed water tank and feed water pipes.
Step H: Clean and grease the bearings of motor, pump, and fan.
Step I: Check and align the burner, if necessary.
Step J: If the boiler is shut down for a long period of time, the smoke tubes, for the
oil fired as well as the exhaust gas part, must be thoroughly cleaned.
Step K: Check that the necessary spare parts are available. Order complementary
parts in time.
Warning: It is of extreme importance that the boiler is NOT operated without
water when the oil burner is in operation, e.g. due to disconnection of
the water level safety devices. This will immediately cause complete
break down of the boiler.
START/STOP OF THE BOILER OM9210_02#C.2
Language UK 8-7 / 32
Boiler maintenance
1 Boiler maintenance
The boiler maintenance should always be executed with skill and in accordance with
valid rules and regulations from the authorities. Below some recommendations are
given for periodical inspections and maintenance.
1.1 Daily operation
During normal operation of the boiler, some work and check procedures have to be
considered every day.
Step A: Check the boiler steam pressure and the water level.
Step B: Check that the feed water control system is operational, see separate in-
structions.
Step C: Check the boiler water condition and make necessary counter measures with
regard to the feed and boiler water treatment. If necessary, blow-down the
boiler.
Step D: Check the function of the oil burner at different capacities through the in-
spection holes on the boiler.
Step E: Check the flue gas temperature after and/or the draft loss across the boiler.
If either the temperature or the draft loss is too high, the smoke tube section,
for the oil fired as well as the exhaust gas part, must be cleaned.
1.2 Weekly routine checks
Step A: Drain each water level glass for about 10-15 seconds.
In case of contaminated boiler water or insufficient water treatment, the draining of
the water level glasses must be done more often.
Step B: Check the safety water level device.
Step C: Depending on the boiler water tests, blow-down the boiler. Open the blow-
down valves quickly for a few seconds, and then close and open again for
about 5-10 seconds.
Repeat this operation when required according to the boiler water tests.
Step D: Perform scum blow out by means of the scum valve when required. The
scum blow out must be carried out until the drained water is clean.
1.3 Monthly routine checks
Step A: Test all stand-by pumps.
Step B: Check all boiler mountings for damage or leaks and repair/replace if neces-
sary.
BOILER MAINTENANCE OM9210_09#A.2
8-8 / 32 Language UK
Step C: Check the function of the high steam pressure switch by lowering the set
point or by raising the steam pressure, e.g. by closing the main steam valve
slowly.
The burner must stop automatically.
2 Inspection of the boiler
2.1 Inspection of furnace
The furnace should be inspected at least twice a year. During this inspection, the fol-
lowing issues should be taken into consideration:

Check for cracks at the refractory lining and that the furnace walls are free from
excessive soot deposits.

Examine carefully the area opposite the burner. Too much soot deposits indicate
that the burner should be adjusted.

Check that the smoke and stay tubes, are intact and that soot deposits are within
normal limits.
2.2 Inspection of exhaust gas section
The exhaust gas section should be inspected at least twice a year. During this inspec-
tion, the following issues should be taken into consideration:

Check the welding in the exhaust gas section. A careful examination should be
carried out with respect to any possible corrosion or crack formation.

Check that the inlet box and outlet box are intact and that soot deposits are within
normal limits.

Check that the smoke tubes and stay tubes are intact and that soot deposits are
within normal limits.
2.3 Inspection of boiler water side
The boiler water side (interior) must be carefully inspected at least twice a year. This
inspection is of great importance and no doubt the most important of all the mainte-
nance measures, since it has a direct influence on the boiler longevity and on the se-
curity.
At these inspections, hard deposits, corrosion, and circulation disturbances can be
found at an early stage, and preventive measures must be taken to avoid unexpected
material damage and boiler breakdown.
The presence of hard deposits at the furnace wall and the smoke tubes reduces their
heat transfer properties and decreases the capacity of the boiler.
Further, it can be established whether the feed water treatment is satisfactory, and
whether the blow-down is carried out sufficiently.
BOILER MAINTENANCE OM9210_09#A.2
Language UK 8-9 / 32
Incorrect feed water treatment is commonly causing hard deposits or corrosion.
Insufficient blow-down will cause sludge deposits in the tubes and accumulation of
sludge in the bottom of the boiler.
If hard deposits are not removed, it may lead to overheating in the boiler plate material,
which is exposed to the flame in the furnace wall area. This may cause material dam-
ages.
Incorrect feed water treatment does not always lead to hard deposits. For example, a
too low or too high pH-value may give an electrolytic reaction, causing corrosion in
the boiler.
When the boiler interior is inspected, examine all parts carefully and be attentive to
deposits, corrosion, and cracks. It is advisable to pay special attention to this inspection.
If any unusual signs are found, contact Aalborg Industries at once for advice.
2.4 Procedure and remarks for inspection
Step A: Shut off the boiler and allow it to cool (below 100C).
Note: The boiler should NOT be depressurised by lifting the safety valves and
then filled with cold feed water as the stress induced by too rapid cooling
may cause damage.
Step B: Empty the boiler and close all valves.
If the boiler is connected to a second boiler, check that the valves between them are
closed.
Step C: Unscrew and remove the manhole hatch(es) on the boiler and enter the boiler
when it is sufficiently cold.
Check the welding in the boiler. A careful examination should be carried out with
respect to any possible corrosion or crack formation.Special care should be taken to
the water line area in the pressure vessel where oxygen pitting may occur.If deposits
are forming in the boiler tubes, the boiler should be chemically cleaned.It is advisable
to consult a company of cleaning specialists who will examine the boiler deposits and
treat the boiler accordingly.
Note: After chemical treatment the boiler should be blown-down at least twice a
day for approximately one week. This will ensure that excessive sludge
deposits due to chemical treatment do not collect in the bottom of the pres-
sure vessel.
2.5 Contamination
If the boiler is contaminated with foreign substances like oil, chemicals, corrosion
products etc., it is very important to act immediately to avoid damage to the boiler.
BOILER MAINTENANCE OM9210_09#A.2
8-10 / 32 Language UK
Layers of thin oil films, mud, etc. exposed to the heating surfaces cause a bad heat
transfer in the boiler, leading to overheating followed by burned out pressure parts. In
order to remove such contamination, a boiling out or acid cleaning should be performed
immediately.
Note: Corrosion products from the pipe system or insufficient boiler water treat-
ment may result in corrosion in the boiler itself. It is therefore important
to observe that such circumstances do not occur in the system.
BOILER MAINTENANCE OM9210_09#A.2
Language UK 8-11 / 32
Boiling out
1 Boiling out
Before putting the boiler into operation for the first time, it should be boiled out to
remove all protecting remedies and impurities on the boiler waterside.
The boiling out procedure is recommended to be carried out as described below:
Caution: Extreme care should be taken while handling the chemicals. The person
handling the chemicals/solution should be properly dressed/protected.
Step A: Fill the boiler with a solution consisting of 4-5 kg trisodiumphosphate
Na3PO4 per 1000 kg water. The chemicals can be added through the man-
hole.
Step B: Add feed water until the solution is visible in the water gauges above lower
water level.
Step C: Close the feed water valve (pump stopped).
Caution: Do never fill feed water into the boiler if the temperature difference
between boiler and feed water exceeds 50C.
Step D: Raise steam pressure slowly to working pressure, and keep the pressure for
approx. 3-4 hours with closed main steam valve.
Step E: Scum until water level is between Normal water level and High water
level.
By this procedure grease and other impurities are removed from the internal surfaces
of the boiler.
Step F: Start skimming by opening the scum valve, and lower the water level to
lower edge of Normal water level mark.
Step G: Close the scum valve.
Step H: Refill the boiler with feed water and start skimming again in intervals of 30
minutes for a period of two hours.
Step I: Stop the boiling out procedure by switching off the burner.
Step J: Let the boiler water rest for about five minutes.
Step K: Carry out a final skimming.
Step L: Blow off the boiler water by opening the blow down valves.
Step M: Remember to open the air escape valve, to avoid a vacuum in the boiler when
the boiler pressure decreases to approx. depressurised/atmospheric pressure.
Step N: Open the manhole and let the boiler cool down to approx. 100C.
BOILING OUT OM9210_11#A.2
8-12 / 32 Language UK
Step O: The boiler is to be flushed with clean water on the boiler waterside, when
the temperature has decreased. The flushing removes remaining impurities.
Step P: Dismantle the bottom blow down valves, for cleaning and inspection be-
cause deposits/foreign substances will usually be accumulated in these
valves and cause leaking if not cleaned.
Step Q: Inspect the boiler and remove any remaining deposits and foreign substan-
ces.
Step R: Finally, new gaskets to be fitted in all hand- and manholes before refilling
the boiler with water to upper edge of Low water level.
The boiler is now ready to be taken into service.
Note: During the first two weeks in operation we recommend to carry out fre-
quently skimming and bottom blow down to remove impurities entering
the boiler from the pipe system.
BOILING OUT OM9210_11#A.2
Language UK 8-13 / 32
Manhole gaskets and hand hole gaskets
1 Gaskets
The gaskets are of a high-tech, compressed fibre material which makes them ideal for
steam.
1.1 Storage and handling
The gaskets should always be stored horizontally to avoid tensions. Also, they should
be stored in clean condition and in a dark storage room.
Ideal temperature: < 25

C.
Ideal air humidity: 50-60%.
Never bend the gaskets or damage their surfaces.
1.2 Installation
Note: For safety reasons, never re-use a gasket.
Make sure that all sealing surfaces are clean and dry. Be sure not to damage/scratch
sealing surfaces while cleaning. Also check that sealing surfaces are parallel and free
of damages and cracks.
All gaskets should be installed clean and dry. No form of gasket compounds can be
used for installation. These might damage the gaskets and result in possible blowouts
of the gaskets. The gaskets are coated with a non-sticking film.
Ensure that bolts and nuts are clean and free of corrosion and apply lubricant on the
threads.The lubricant must not contaminate gaskets or sealing surfaces. Insert the gas-
kets carefully in the covers and place the covers with the new gaskets in the manholes/
hand holes. Ensure that the coversare centralized in the manholes/hand holes.
Make at least 4 stages to the required torque.

Finger-tighten the bolts.

Use 30% of the required torque.

Use 60% of the required torque.

Use the required torque.

1.3 Recommended torque

Manhole : 250 Nm.

Hand hole: 500 Nm.

MANHOLE GASKETS AND HAND HOLE GASKETS OM9010_39#B.2
8-14 / 32 Language UK
1.4 Re-tightening
Re-tightening must be done in hot condition during the first 24 hours of the starting-
up of the plant. Re-tightening of high-tech, compressed fibre gaskets under pressure
and after a long period of operation might lead to leaking gaskets and possible blow-
outs.
MANHOLE GASKETS AND HAND HOLE GASKETS OM9010_39#B.2
Language UK 8-15 / 32
Cleaning pin-tube elements
1 General
In order to keep the heat transfer area sufficiently clean, the boiler has been designed
with a high flue-gas velocity through the pin-tube elements. Therefore fouling will be
minimised, under normal circumstances, with a correct combustion.
After a certain time in operation, soot deposits are however accumulated inside the
boiler. The quantity of soot and the time of forming it, depends on factors such as oil
quality, boiler load, and burner adjustment. It is impossible to specify exact time in-
tervals in which the boiler should be soot cleaned. However, some general guidelines
are given below.
There are three methods to check if soot cleaning is necessary:

Inside inspection.

Check of the flue gas temperature. The boiler should be cleaned if the flue gas
temperature is approximately 20C above the temperature for a clean boiler.

Check of the pressure loss. The boiler should be cleaned if the pressure loss is
approximately 20 mm WC above the pressure loss for a clean boiler.
It is recommended to keep a consecutive record of the flue gas temperature and the
pressure loss related to different boiler loads for a clean boiler. These original data
should be used for comparison, and it is recommended to plot the measurements in a
chart like the one shown in Figure 1. In this way it is possible to monitor the fouling
condition of the pin-tubes and determine when they need to be cleaned.
Checkscheme for flue gas measurement
Figure 1 om9210_12_dp_tubx0059610en.wmf
CLEANING PIN-TUBE ELEMENTS OM9210_12#A.2
8-16 / 32 Language UK
2 Water washing procedure
The most effective way of soot cleaning is water washing, as most of the deposits
consist mainly of non-soluble particles held together by a water soluble bonding ma-
terial. Water washing will have the following benefits:

Dissolves the bonding material.

Washes the loosened insoluble deposits away.

Water washing must be carried out when the oil burner is stopped and the boiler has
been cooled down. However, the boiler should be warm enough for the water to evap-
orate so that the pin-tube elements and furnace will not remain moist after washing.
Both fresh and sea water can be used. However, if sea water is used, the boiler must
be thoroughly washed afterwards with fresh water in order to remove all salt deposits.
Where deposits are highly corrosive or bonded, a soaking spray with a 10% soda ash
solution is advisable before washing.
Step A: Ensure that the oil burner is stopped and remains stopped.
Step B: Wait a minimum of time allowing the boiler to cool (below 100C).
Step C: Unlock the burner unit and swing it out of the furnace.
Step D: If loose particles or soot are found on the furnace floor remove these.
Step E: Open furnace drain valve and check that the pipe is not blocked. If the drain
pipe at the furnace bottom is provided with a plug this must also be removed.
Step F: Unlock and remove the inspection hatches of the smoke outlet box located
on top of the boiler.
Step G: Start water washing using a hand water lance or fire hose inserted through
the inspection hatch of the smoke outlet box and direct the jet of water di-
rectly at each of the vertical uptakes. In the beginning the water supply
should only be slightly opened, just enough to have a small amount of water
to ensure that the drain is working properly.
Warning: When the pin-tube elements are water washed, there is a risk of gen-
erating steam. It is therefore very important that all of your body is
outside the smoke outlet box in order not to get your skin burned by
the steam.
Step H: When it has been ensured that the washing water is running freely down
through the drain system, increase the water flow and flush carefully over
each tube for 20-30 seconds. The water flow should be approximately 50 l/
min at a water pressure between 4-6 bar.
Note: Care should be taken not to let water get in contact with the burner throat
refractory.
Step I: It is important to check that the drain and soot collecting system are working
properly during the whole water washing procedure.
CLEANING PIN-TUBE ELEMENTS OM9210_12#A.2
Language UK 8-17 / 32
Step J: When the water washing has begun, it must be completed until the pin-tube
elements are thoroughly washed and all deposits are removed. This is due
to the fact that some types of coatings harden and accordingly get very dif-
ficult to loosen when they have been saturated and then dry out.
Step K: When the water washing has been completed, the pin-tube elements and
furnace floor must be cleaned with alkaline water because the washing water
is very corrosive.
Step L: It must be ensure that all the washing water is drained away and loosened
deposits are removed from the furnace floor by looking into the furnace.
Step M: Mount the inspection hatches on the smoke outlet box and secure them.
Step N: Swing the burner back into position and dry out the boiler by starting the
burner fan in manual operation for approximately 15 minutes. It is essential
that the boiler is dried out immediately after water washing. This is because
soot formations produced by an oil burner, contains sulphur compounds.
Any residual soot and water will therefore react chemically to form a highly
corrosive sulphuric acid.
Step O: Check that the furnace drain pipe has not become blocked and close the drain
valve. If the drain pipe at the furnace bottom is provided with a plug it will
be necessary to swing out the burner again to insert the plug.
Important: The refractory in the furnace must be heated slowly up in order to
let the water absorbed by the refractory evaporate slowly.
Step P: Within the first hour; start the burner at minimum load for one (1) minute.
Then stop it and wait for three (3) minutes before restarting it again.
Step Q: Within the second hour; start the burner at minimum load for two (2) mi-
nutes. Then stop it and wait for two (2) minutes before restarting it again.
Step R: Within the third hour; start the burner at minimum load for two (2) minutes.
Then stop it and wait one (1) minute before restarting it again.
Step S: Finally start the burner at minimum load and let it operate at that load for
the next two hours.
Step T: The boiler can now be brought back into normal service. During normal
operation check that the flue gas temperature is now within the correct limits.
CLEANING PIN-TUBE ELEMENTS OM9210_12#A.2
8-18 / 32 Language UK
Cleaning smoke tubes
1 General
The heating surface dimensions of the smoke tubes are designed to maintain a sufficient
exhaust gas velocity giving the best self-cleaning effect within the design limits. How-
ever, after long term operation soot deposits can be accumulated inside the smoke
tubes. The main engine exhaust gas contains carbon particles and un-burnt residues
(soot, etc.) and the amount is strongly dependent on the state of the engine and the
supply of scavenging air. These soot/un-burnt residues will accumulate in the smoke
tubes if not removed by cleaning. Furthermore, the combustion quality of the engine
is changing together with the load, where the best combustion is in the high load range
and the lower range is giving a more contaminated (black/coloured) exhaust gas.
And the more contaminated the exhaust gas is, the more fouling will appear in the
smoke tubes.Therefore, it is impossible to specify exact time intervals in which the
smoke tubes should be soot cleaned. However, some general guidelines are given be-
low:

Inside inspection.

Check of the exhaust gas temperature on the outlet side of the boiler. The boiler
should be cleaned if the outlet exhaust gas temperature lies approx. 20C above
the temperature in a clean boiler at a specified engine load.

Check of the pressure loss. The boiler should be cleaned if the pressure loss lies
approx. 20 mm WC above the pressure loss in a clean boiler.
It is recommended to keep a consecutive record of the exhaust gas temperature and
pressure loss related to different engine loads in a clean boiler. These original data
should be used for comparison, and plotted into a measurement chart like the one shown
in Figure 1. In this way it is possible to monitor the fouling condition of the smoke
tubes and determine when they need to be cleaned.
Check scheme for exhaust gas measurements
0 10 20 30 40 50 60 70 80 90 100
Load %
O
u
t
l
e
t

G
a
s

T
e
m
p
.

[

C
]
D
i
f
f
.

P
r
e
s
s
u
r
e

[
m
m
W
C
]
Diff. pressure
Outlet temp.
Figure 1 om9210_14_dp_tobx0059620en.wmf
CLEANING SMOKE TUBES OM9210_14#A.2
Language UK 8-19 / 32
2 Water washing procedure
The most effective way of soot cleaning is water washing, as most of the deposits
consist mainly of non-soluble particles held together by a water soluble bonding ma-
terial. Water washing will have the following benefits:

Dissolves the bonding material.

Washes the loosened insoluble deposits away.

Water washing must be carried out when the main engine is stopped and the boiler has
been cooled down. However, the boiler should be warm enough for the water to evap-
orate so that the tubes will not remain moist after washing.
Both fresh and sea water can be used. However if sea water is used, the boiler must be
thoroughly washed afterwards with fresh water in order to remove all salt deposits.
Where deposits are highly corrosive or bonded, a soaking spray with a 10% soda ash
solution is advisable before washing.
Step A: Ensure that the main engine is stopped or by-pass the exhaust gas flow, if
possible. Also secure that the oil burner is stopped and remains stopped.
Step B: Wait a minimum of time allowing the boiler to cool.
Step C: Unlock and remove the inspection doors at the exhaust gas inlet box and
outlet box.
Step D: Open the drain at the bottom of the inlet box to the soot collecting system,
and make sure that there is free passage.
Step E: Open drains at the turbo chargers and make sure that there is free passage.
Step F: If there is a risk that the washing water will run into the exhaust gas pipe
and down to the turbo chargers, the exhaust gas pipe must be covered. This
can be done by e.g. covering the exhaust gas inlet pipe with a waterproof
tarpaulin as indicated inFigure 2.
Step G: Start water washing using a hand water lance or fire hose inserted through
the inspection door of the outlet box and direct the jet of water directly at
the smoke tubes. In the beginning the water supply should only be slightly
opened, just enough to have a small amount of water to ensure that the
drainsare working properly.
Step H: When it has been ensured that the washing water is running freely down
through the drain system into the soot collecting system, the water amount
can slowly be increased, until a flow of approximately 50 l/minat a water
pressure between 4 to 6 bar is obtained.
Warning: When the smoke tubes are water washed, there is a risk of generating
steam. It is therefore very important that all of your body is outside
the outlet box in order not to get your skin burned by the steam.
Step I: It is important to check that the drain and soot collecting system are working
properly during the whole water washing procedure.
CLEANING SMOKE TUBES OM9210_14#A.2
8-20 / 32 Language UK
Step J: When the water washing has begun, it must be completed until the smoke
tubes are thoroughly washed and all deposits are removed. This is due to the
fact that some types of coatings harden and accordingly get very difficult to
loosen when they have been saturated and then dry out.
Water washing of the exhaust gas side
Water washing hose
Waterproof tarpaulin
Exhaust gas inlet
Exhaust gas outlet
Inspection door
Inspection door
Inlet box drain
Figure 2 om9210_14_oc2x0059630en.wmf
Step K: When the water washing has been completed, it must be ensure that all the
washing water is drained awayby looking into the inlet box from the in-
spection door. The bottom of the inlet box must be cleaned with alkaline
water because the washing water is very corrosive.It must be observed that
all the washing water and loosened deposits are removed from the boiler.
Step L: The boiler must be dried out immediately after water washingby having a
natural air circulation through the boiler or by heating it up with feed water.
This is because soot formations produced by the combustion process in the
engine contain sulphur compounds. Any residual soot and water will there-
fore react chemically to form a highly corrosive sulphuric acid.
Step M: Remove the waterproof tarpaulin from the exhaust gas inlet pipe, if inserted,
and close drains as well as inspection doors.
Step N: The boiler can now be brought back into normal service.
CLEANING SMOKE TUBES OM9210_14#A.2
Language UK 8-21 / 32
Preservation
1 Preservation of the boiler
If the boiler is to be shutdown for a period of 1-30 days, it should be top filled to prevent
corrosion. Before top filling, it should be cleaned from soot deposits.
If the boiler is to be shut down for more than one month, different methods to prevent
corrosion can be applied:

Dry preservation.

Wet preservation.

Nitrogen preservation.

VCI preservation.
The work procedures related to each of these preservation methods are described in
the following:
1.1 Dry preservation
When this method is applied the boiler should be totally emptied off water and dried
out.
Step A: Empty the water/steam contents inside the boiler by means of the bottom
blow down at a boiler pressure of 3-5 barg. Open the boiler when it is dep-
ressurised and drain offany remaining water.
Step B: Manhole doors and hand hole covers should be opened when the boiler is
still hot. If there is water left in the bottom of the boiler it must be removed,
e.g., by using a vacuum cleaner.
Step C: If the boiler is cold, drying of the boiler can be done by either circulating
dried air from a fan or by placing bags of silicagel inside the boiler.
Step D: Before the manhole doorsand hand hole covers are closed, place a tray with
burning charcoal to remove oxygen. As soon as the tray with charcoal is in
position, close the manhole doors and hand hole covers using new gaskets.
Step E: Alternatively, a small steam phase inhibitor can be added to the boiler after
cooling and careful draining. Afterwards the boiler should be closed com-
pletely.
1.2 Wet preservation
While dry preservation is a question of draining off water to avoid corrosion, the prin-
ciple of wet preservation is to prevent oxygen from entering the boiler.
This method can be used for a short period of lay-up (1-3 months).
Step A: The boiler is filled with treated boiler water and hydrazine is added until an
excess of 100-200 ppm is obtained.
PRESERVATION OM9210_13#A.2
8-22 / 32 Language UK
Step B: The water should be circulated continuously or at least once per week to
avoid corrosion from any penetration of oxygen, and it is necessary to check
the hydrazine concentration and add the necessary amount to have an excess
of 100-200 ppm. Other oxygen binding agents can also be used.
The pH-value should be 9.5-10.5.
Note: If there is any risk of the temperature falling back below 0C, this method
should not be used to avoid frost damages.
As this preservation method involves applying hydrazine to the water inside the boiler,
the boiler must be completely drained and refilled with fresh water before taken into
service again.
1.3 Nitrogen preservation
The boiler should be drained, dried and sealed in the same way as mentioned in section
1.1,Dry preservation.
Step A: Make a connection point to the bottom of the boiler and open the air escape
valve on top of the boiler.
Step B: Connect cylinders with nitrogen to the bottom connection point via a re-
duction valve and purge the boiler until there is no oxygen left.
Step C: Close the air escape valve.
Step D: Leave a cylinder with nitrogen connected to the boiler via a reduction valve
and keep an overpressure of approximately 0.2 bar inside the boiler.
1.4 VCI preservation
An alternative to the above mentioned preservation methods may be the use of a so-
called volatile corrosion inhibitor (VCI).
The VCI is a water soluble chemical which partly evaporates and protects both the
water and steam spaces of the boiler. It should be able to eliminate the need for complete
drainage and/or application of nitrogen, and may in particular be interesting when a
forced circulation type exhaust gas boiler is installed in the steam system. The boiler
must be effectively sealed from the atmosphere to maintain the corrosion protection.
The VCI is offered by various chemical companies and must be used in accordance
with their recommendations.
PRESERVATION OM9210_13#A.2
Language UK 8-23 / 32
Boiler repair - pin-tube element
1 Repair of a pin-tube element
In the unlikely event of a leaking pin-tube element, the burner and feed water pump
must be stopped and the boiler depressurised.
Step A: Open the blow-down valves and drain the boiler for water.
Step B: Removed the manhole cover.
Step C: The boiler should now be inspected in order to locate the damaged pin-tube
element.
1.1 In case of a damaged pin-tube element
The pin-tube element must be blocked by welding circular plates, with the same di-
ameter as the outer tube, at the inlet and outlet of the outer tube (see Figure 1).
The circular plates must be made of boiler plate and should be approx. 15 mm thick.
The welding must be performed by skilled personnel with knowledge and qualifica-
tions to perform certified welding.
Step A: Gain access to the damaged tube through the smoke outlet box, furnace, and/
or manhole.
Step B: Before repairing a damaged pin-tube element the inner and outer tube should
be cleaned.
Step C: Cut two holes in the outer tube prior to mounting the circular plates, as shown
in Figure 1.
Step D: Fit and weld the circular plates at the inlet and outlet of the outer tube. After
completion of the repair work clean the working area.
Step E: Close all access doors and mount the manhole cover. Replace the gasket if
necessary.
Step F: Refill the boiler with feed water and check for leaks before starting up.
Step G: Start the boiler and check for leaks when the boiler is pressurised.
Note: When a pin-tube element has been plugged as described above, a new pin-
tube element should be mounted as soon as possible. The boiler should NOT
be operated with more than one blocked pin-tube element, without appro-
val from the supplier.
Attention: The classification society should be notified about the repair work and
a schedule must be made for exchange of the damaged tubes.
BOILER REPAIR - PIN-TUBE ELEMENT OM9210_20#A.2
8-24 / 32 Language UK
Temporary repair of pin-tube elements has naturally an influence on the efficiency
since the heating surface is reduced. It can therefore be expected that the flue gas
temperature will rise. It should be noted that the flue gas temperature never must exceed
400C. If the temperature exceeds 400C the burner must be stopped or fired at a low
firing rate.
Note: Temporary repairs require more attention than a normal working boiler.
Illustration of how to block a pin-tube element
Repair plate
Repair plate
Holes to be cut before welding
of the repair plates (35)
min. 100 mm
min. 100 mm
Repair plates:
MISSION OS, OC boilers: 256
MISSION OM boilers: 252
Figure 1 om9210_20_pin_rex0059690en.wmf
BOILER REPAIR - PIN-TUBE ELEMENT OM9210_20#A.2
Language UK 8-25 / 32
Plugging of smoke tubes
1 General
In case of a leakage tube, the boiler must be stopped and the pressure lowered to
atmospheric pressure. If the leaking tube cannot be located immediately via the in-
spection doors at the exhaust gas inlet and outlet boxes, the boiler should be set on
pressure by means of the feed water pumps so that the leakage indicates the damaged
tube.
1.1 Plugging of smoke tubes
Step A: The oil burner and main engine must be stopped during the repair work.
Step B: Open and, if necessary, remove the inspection doors in the exhaust gas inlet
box and outlet box.
Step C: When the damaged tube has been located, clean the inside of the tube ends
with a steel brush so that no deposits are present in the tube.
Step D: Plug and seal weld both tube ends with a conical plug, see Figure 1.
Note: Temporary repairs require more attention than a normal working boiler.
Tube plugging results in reduced efficient heating surface, and accordingly
the boiler efficiency will decrease.
Attention: The classification society should be notified about the repair work and
a schedule must be made for exchange of the damaged tubes.
1.2 Exchange of smoke tubes
From an operational point of view up to 10% to 15% of all smoke tubes can be plugged
with a conical plug, but if more tubes are damaged, an exchange of tubes is necessary.It
is possible to replace the smoke tubes from the outside of the boiler. After location of
the damaged tube or tubes, they must be replaced according to the following procedure:
Step A: The oil burner and main engine must be stopped during the repair work.
Step B: Ensure that the boiler pressure is lowered to atmospheric pressure and that
it is completely drained of water.
Step C: Open inspection doors, manhole cover, and hand hole covers.
Step D: Adequate amounts of insulation material as well as shell plate should be
removed for the repair work.
Step E: The damaged tubes must be cut right below and above the tube plates.
Step F: Remove the damaged tubes.
Step G: Scraps of metal and welding material in the tube holes as well as the end
plates must be grinded off.
PLUGGING OF SMOKE TUBES OM9210_22#A.2
8-26 / 32 Language UK
Step H: Depending on the present conditions the new smoke tubes should be inserted
from either the top or bottom. This means that either parts of the smoke outlet
or the boiler bottom must be removed.
Step I: The new tubes should be placed in the tube holes one by one and seal welded
onto the tube plates as shown in Figure 1. During the assembling the supports
are arranged and adjusted.
Note: Only skilled personnel with knowledge and qualifications to perform cer-
tified welding should perform repair work.
Illustration of how to exchange and block a smoke tube
Top end plate
Plugging of tube
Conical tube plug Bottom end plate
Exchange of tube
2.5
3.5
Figure 1 om9210_22_oc03x0059720en.wmf
Step J: The tubes should be rolled after the welding work has been completed.
Step K: After completion of the repair work, clean the working area.
Step L: Previously removed boiler shell plate as well as smoke outlet or boiler bot-
tom must be rebuilt and insulated.
Step M: Mount manhole cover and hand hole covers. Renew gaskets if necessary.
Step N: Refill the boiler with water and check for leaks through the inspection doors
before starting up.
Step O: Mount and close the inspection doors again.
PLUGGING OF SMOKE TUBES OM9210_22#A.2
Language UK 8-27 / 32
Boiler repair - refractory
1 Refractory repair
The furnace floor is lined with an insulating material (Verilite R6), close to the casing
covered with a layer of castable refractory (Plicast 31).
The refractory is made with expansion joints, which should under no circumstances
be blocked or filled on purpose.
Even though the refractory is made with expansion joints, it will tend to make additional
natural expansion joints, which will be seen as fissures. However, the fissures will
generally close when the boiler is put into service. Please note the following guidelines
when examining the fissures:

white/light fissures, which are getting darker over the time and are closing when
the boiler is in service and opening in cold condition, need no further attention.

dark/black fissures suddenly occurred, seen in cold condition and are not closing
when boiler is in service need to be repaired/filled up with refractory (Plicast 31).
All refractory subjected to wear will, eventually, need to be repaired. This can be done
as a temporary repair or on a permanent basis.
1.1 Temporary repair
Smaller areas can be temporarily repaired making use of the repair mix Plistix 14,
supplied separately with the boiler equipment.
The durability of such a repair depends on the location, but the more exposed to heat,
the shorter lifetime. Generally, it is recommended to replace a temporary repair with
a repair on a permanent basis within one year.
Temporary repairs in vertical places ought to be made swallow tailed, see Figure 1,
if possible. This secures a better attachment to the existing refractory.
BOILER REPAIR - REFRACTORY OM9210_25#A.2
8-28 / 32 Language UK
Sketch indicating a swallow tail repair
Refractory Swallowtail
(filled in with Plistix 14)
Figure 1 om9210_25_swaltax0059780en.wmf
The surface to which the temporary repair is performed, must always be clean, dry and
rugged.
Mixing instructions for the castable refractory appears from the instruction on the
plastic bucket.
Note: Plistix 14 must be applied to the site immediately when mixed.
The boiler can be lightened-up approx. 1 hour after the refractory has been applied.
The refractory needs no further time for hardening.
If the boiler is pressurized, the lighting-up should be started with the burner in on
position for one (1) minute and then in off for two (2) minutes, during the first half
() hour. Then it can be started up according to the ordinary lighting-up procedure.
Note: Observe the safety rules regarding the refractory which can be seen on the
plastic bucket.
1.2 Permanent repair
Major repairs and renewal of temporary repairs shall always be carried out and super-
vised by makers specialists, among other things securing that correct drying-out time
and lighting-up is observed.
1.3 Boilers with membrane furnace wall
The refractory applied to a damaged membrane furnace wall must be carried out as
shown in Figure 2.
BOILER REPAIR - REFRACTORY OM9210_25#A.2
Language UK 8-29 / 32
Refractory applied to a membrane furnace wall
Failed tube
Plicast 31
Furnace tube
Figure 2 om9210_25_plugrex0059770en.wmf
Warning: Failed Y-anchors must only be replaced by Y-anchors made from heat
resistant steel. Y-anchors made from incorrect materials will cause
damage to the refractory.
2 Maintenance of refractory
Note: The refractory should be inspected once a year for shape and wear. It is
recommended to carry out an inspection in due time prior to long repair
periods such as dry docking, etc. Should a repair be required castable re-
fractors and bricklayers can then be ordered on short notice.
If the refractory has been exposed to water, the refractory should be dried out as soon
as possible. The drying out can be done by hot air (approx. 50C) or by operating the
oil burner.
Warning: However, if the burner is being used, the burner should be operated
with great care.
Warning: Generated steam evaporated from water absorbed into the refractory
might cause fissures and cracks when expanding, if the heat input from
the oil burner is too heavy.
2.1 Typical refractory data
Below in Table 1 is a list of typical refractory data shown.
BOILER REPAIR - REFRACTORY OM9210_25#A.2
8-30 / 32 Language UK
Refractory data
Verilite R6 Plicast 31 Plistix 14
Al2O3 32% 44% 48%
SiO2 24% 46% 43%
Fe2O2 12% 1% 1%
TiO2 1.6% 1% 1.9%
CaO 23.3% 6.5% 4.8%
MgO 6.1% 0.5% 0.2%
Alkanes 1% 1% -
Na2O - - 0.1%
K2O - - 0.2%
Operating range 100-1000C 20-1450C 100-1420C
Table 1
BOILER REPAIR - REFRACTORY OM9210_25#A.2
Language UK 8-31 / 32
Lighting-up curve
1 Lighting-up curve for MISSION boilers
Figure 1 shows the lighting-up curve for MISSION boilers. When the burner is
started the firing capacity must be adjusted to match the lighting-up curve. Further
start/stop instructions are described in the chapter Start/stop of the boiler.
Lighting-up curve for MISSION
TM
boilers
0
1
2
3
4
5
6
7
8
10
12
14
16
0 15 30 45 60 75 90 105 120 150 135
0
25
50
75
100
125
150
175
100 50 30 15 0
200
225
Time (min.)
Temperature ( C)
o
Boiler pressure (barg) t: Boiler temperature at start
18
20
25
150
Figure 1 om9210_31_startcx0059840en.wmf
LIGHTING-UP CURVE OM9210_31#A.2
8-32 / 32 Language UK
Table of contents
Feed and boiler water
Description Document ID Page
.
Feed and boiler water................................................. OM9210_99............... 9-2
TABLE OF CONTENTS
Language UK 9-1 / 15
Feed and boiler water
1 General
Note: The recommended feed and boiler water characteristics are only valid for
boilers with a working pressure below 20 barg.
There is a number of ways to produce good quality feed water for boiler plants. Methods
such as e.g. reverse osmosis plants or ion exchange plants produce good quality dis-
tillate. Also evaporators generally produce good distillate. The important thing is that
the distillate used should be clean and without foreign salt contamination.
In practice most distillates used contain minor parts of various salt combinations which
can and must be chemically treated away. Furthermore, the distillate may contain dis-
solved gases like for example oxygen (O2) and carbon dioxide (CO2) which may lead
to corrosion in the boiler, steam, and condensate system.
Important: Boiler and feed water must be chemically treated in order to avoid
corrosion and scaling in the boiler.
2 Layout of the treatment system
The condition of the feed and boiler water is an essential part of the boiler operation
and operation philosophy. The design and construction of the treatment system should
therefore be considered carefully during layout of the plant. Aalborg Industries gives
some general requirements and recommendations regarding the conditions of the feed
and boiler water. However, there is several ways to obtain this results, or similar, by
using different treatment systems. The following should therefore be considered al-
ready at the layout stage:
- Choose the treatment system that should be used.
- Present the condensate and feed water system to the supplier of the treatment sys-
tem and inform about the operation philosophy of the plant.
- Let the supplier indicate where the injection points should be located and also
inform if special equipment is required.
- Let the supplier inform about which test facilities is needed.
- Purchase the recommended equipment and install it in the correct way.
- Use the treatment system as soon as the boiler is taken into operation.
FEED AND BOILER WATER OM9210_99#B.1
9-2 / 15 Language UK
3 Feed and boiler water characteristics
The following text regarding feed and boiler water treatment is the normal recom-
mendations given by Aalborg Industries. These recommendations should be followed
strictly in order to have the best working conditions for the boiler plant and to extend
the working life of the plant. The requirements/recommendations of the various values
for feed and boiler water are listed in Table 1 below.
Requirements for feed and boiler water
Unit Feed water Boiler water
Appearance - Clear and free of mud Clear and free of mud
Hardness ppm CaCO3 0 - 5 -
Chloride content ppm Cl
-
<15 <100
"P" alkalinity ppm CaCO3 - 100 - 150
Total (T) alkalinity ppm CaCO3 - <2 x "P" - Alkalinity
PH-value at 25C - 8.5 - 9.5 10.5 - 11.5
Hydrazine excess ppm N2H4 - 0.1 - 0.2
Phosphate excess ppm PO4 - 20 - 50
Specific density at 20C Kg/m
3
- <1.003
Conductivity at 25C S/cm - <2000
Oil content - NIL NIL
Table 1
If hydrazine (N2H4) is not used, sodium sulphate (Na2SO3) can be used instead, and
the excess should be 30 - 60 ppm.
In cases where other kinds of oxygen binding agents are used, it is recommended that
an excess of oxygen binding agents can be measured and indicates that no oxygen has
been dissolved in the boiler water.
If it is requested to measure the content of dissolved oxygen directly, it is recommended
to keep the value < 0.02 ppm.
In addition to the above values, the various water treatment companies will add further
demands, depending on the method used for treatment of feed and boiler water.
However, the most important point is that the above values or their equivalents are
observed and that a regular (daily) test of feed and boiler water is carried out.
3.1 Units of measurement
Concentrations are usually expressed in "ppm" i.e. parts solute per million. Concen-
trations for parts solution by weight are the same as "mg/litre".
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-3 / 15
3.1.1 Specific gravity
As guidance the following conversion can be used:
1 Be = 10.000 mg/l total dissolved solids (TDS)
1 mg/l total dissolved solids = 2 S/cm
1 S/cm = 1 mho
4 Feed and boiler water maintenance
The following are recommended water maintenance instructions. More exact details
concerning analyses and blow downs should be set up together with the supplier of
chemicals for water treatment.
4.1 Recommended water maintenance
4.1.1 Daily
Step A: Analyses of feed and boiler water.
4.1.2 Weekly
Step A: Skimming (surface blow down) according to analyses, but at least once per
week (2 minutes with fully open valve).
Step B: Blow down (bottom blow down) according to analyses, but at least once per
week (each blow down valve 1 minute in low load condition).
4.1.3 Monthly
Step A: Check the functions for salinity and oil detection systems.
4.1.4 Every six months
Step A: The boiler water side (interior) must be carefully inspected at least twice a
year.
4.1.5 Yearly
Step A: Check of the water side of the boiler and hotwell/deaerator for corrosion and
scaling.
Step B: Check the chemical pump unit.
5 Treatment systems / injection points
In the following tables and illustrations a number of different feed and boiler water
treatment systems are shown together with the recommended location for the injection
point of the individual chemicals as stated by the manufacturer. The general informa-
tion regarding the injection point principle can be used as guidelines for the most
common systems. But should there be any doubt for a specific system the manufacturer/
supplier should be consulted in order to obtain the correct result.
FEED AND BOILER WATER OM9210_99#B.1
9-4 / 15 Language UK
Notes for tables/illustrations:

Note No. 1: the preferred injection point of chemicals stated by the manufacturer/
supplier.

Note No. 2: the alternate injection point of chemicals stated by the manufacturer/
supplier.

Note No. 3: Valid for modulating feed water systems.

Note No. 4: valid for on/off operating feed water systems. The chemical pump
starts/stops together with the feed water pump.

Note No. 5: valid for two boiler installation. Control of the chemicals in question
work properly at an equal load condition (feed water flow) on the two boilers.
How to use the tables:
The tables can be used in different ways but the main idea is to do following:
Step A: Discover which manufacturer and type of chemicals that should be used for
the actual boiler plant.
Step B: Use the name of the manufacturer and type of chemicals to select which
tables that can be used.
Step C: Check the flow diagrams (Figure 1, Figure 2, or Figure 3) to find a diagram
that matches the actual boiler plant.
Step D: Find in the selected tables the table which includes the matching diagram.
Step E: If more than one table is found to match the actual boiler plant in question
it is recommended to use the method/table which includes note No. 1.
Step F: If no table is found to match the actual boiler plant in question it is recom-
mended to seek assistance by the chemical manufacturer/supplier.
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-5 / 15
Chemical injection points
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 1
Product name / method: Standard with Drewplex OX
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Adjunct B 3, 3a, 3b X 1
1, 2, 3
GC 3, 3a, 3b X 1
SLCC-A 3, 3a, 3b X 1
Drewplex OX 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 2
Product name / method: Standard with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Adjunct B 3, 3a, 3b X 1
1, 2, 3
GC 3, 3a, 3b X 1
SLCC-A 3, 3a, 3b X 1
Amerzine 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 3
Product name / method: Standard with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Adjunct B 3 X
1
GC 3 X
SLCC-A 3 X
Amerzine 1 X 2, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 4
Product name / method: Standard with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Adjunct B 3a, 3b X
2, 3
GC 3a, 3b X
SLCC-A 3a, 3b X
Amerzine 1 X 2, 3, 4, 5
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 5
Product name / method: Drewplex AT / OX
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Drewplex AT 3, 3a, 3b X 1
1, 2, 3
Drewplex OX 2, 2a, 2b X 1, 3, 4


FEED AND BOILER WATER OM9210_99#B.1
9-6 / 15 Language UK
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 6
Product name / method: Drewplex AT / OX
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Drewplex AT 2, 2a, 2b X 2, 3, 4
1, 2, 3
Drewplex OX 2, 2a, 2b X 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 7
Product name / method: Drewplex AT with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Drewplex AT 3, 3a, 3b X 1, 3, 4
1, 2, 3
Amerzine 2, 2a, 2b X 1, 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 8
Product name / method: Drewplex AT with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Drewplex AT 2, 2a, 2b X 2, 3, 4
1, 2, 3
Amerzine 2, 2a, 2b X 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 9
Product name / method: Drewplex AT with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Drewplex AT 2, 2a, 2b X 2, 3, 4
1, 2, 3
Amerzine 1 X 2, 3, 4, 5


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 10
Product name / method: AGK-100 with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
AGK-100 2, 2a, 2b X 1, 3, 4
1, 2, 3
Amerzine 2, 2a, 2b X 1, 3, 4


FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-7 / 15
Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 11
Product name / method: AGK-100 with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
AGK-100 2, 2a, 2b X 3, 4
1, 2, 3
Amerzine 1 X 2, 3, 4, 5


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 12
Product name / method: AGK-100 with Amerzine
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
AGK-100 1 X 2, 3, 4, 5
1, 2, 3
Amerzine 1 X 2, 3, 4, 5


Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 13
Product name / method: Standard
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Alkalinity control 3, 3a, 3b X 1, 3, 4
1, 2, 3
Phosphate 3, 3a, 3b X 1, 3, 4
Oxycontrol 2, 2a, 2b X 1, 3, 4
Marichem CCI 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 14
Product name / method: Standard
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Alkalinity control 1 X 2, 3, 4
1
Phosphate 1 X 2, 3, 4
Oxycontrol 2 X 3, 4
Marichem CCI 2 X 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 15
Product name / method: BWT new formula
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT new formula 2, 2a, 2b X 1, 3, 4
1, 2, 3
Marichem CCI 2, 2a, 2b X 1, 3, 4


FEED AND BOILER WATER OM9210_99#B.1
9-8 / 15 Language UK
Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 16
Product name / method: BWT new formula
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT new formula 1 X 2, 3, 4, 5
1, 2, 3
Marichem CCI 2, 2a, 2b X 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 17
Product name / method: BWT
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT powder 2, 2a, 2b X 1, 3, 4
1, 2, 3
Marichem CCI 2, 2a, 2b X 1, 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Marichem
Table No. 18
Product name / method: BWT
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT powder 1 X 2, 3, 4, 5
1, 2, 3
Marichem CCI 2, 2a, 2b X 3, 4


Chemical injection points (continued)
Manufacturer / supplier: Ashland Chemical / Drew Marine Division
Table No. 19
Product name / method: I
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 3, 3a, 3b X 1
1, 2, 3
Alkalinity control 3, 3a, 3b X 1
Oxygen control 2, 2a, 2b X 1, 3, 4
Condensate control 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 20
Product name / method: I
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 1 X 2
1
Alkalinity control 1 X 2
Oxygen control 2 X 3, 4
Condensate control 2 X 3, 4
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-9 / 15
Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 21
Product name / method: II
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 3, 3a, 3b X 1
1, 2, 3
Alkalinity control 3, 3a, 3b X 1
Cat sulphite L (CSL) 2, 2a, 2b X 1, 3, 4
Condensate control 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 22
Product name / method: II
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 1 X 2
1
Alkalinity control 1 X 2
Cat sulphite L (CSL) 2 X 3, 4
Condensate control 2 X 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 23
Product name / method: Liquitreat
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Liquitreat 3, 3a, 3b X 1
1, 2, 3
Condensate control 2, 2a, 2b X 1, 3, 4
(Oxygen control) 2, 2a, 2b X 1, 3, 4

Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 24
Product name / method: Liquitreat
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Liquitreat 1 X 2
1
Condensate control 2, 2a, 2b X 3, 4
(Oxygen control) 2, 2a, 2b X 3, 4

Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 25
Product name / method: Combitreat
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Combitreat 3, 3a, 3b X 1
1, 2, 3
Condensate control 2, 2a, 2b X 1, 3, 4
Oxygen control 2, 2a, 2b X 1, 3, 4

FEED AND BOILER WATER OM9210_99#B.1
9-10 / 15 Language UK
Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 26
Product name / method: Combitreat
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Combitreat 1 X 2
1
Condensate control 2 X 3, 4
Oxygen control 2 X 3, 4

Chemical injection points (continued)
Manufacturer / supplier: Unitor Chemicals
Table No. 27
Product name / method: I
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 3, 3a, 3b X 1
1, 2, 3
Alkalinity control 3, 3a, 3b X 1
Hydrazine 2, 2a, 2b X 1, 3, 4
Condensate control 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 28
Product name / method: I
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 1 X 2
1
Alkalinity control 1 X 2
Hydrazine 2 X 3, 4
Condensate control 2 X 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 29
Product name / method: II
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 3, 3a, 3b X 1
1, 2, 3
Alkalinity control 3, 3a, 3b X 1
Oxygen control 2, 2a, 2b X 1, 3, 4
Condensate control 2, 2a, 2b X 1, 3, 4
Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 30
Product name / method: II
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
Hardness control 1 X 2
1
Alkalinity control 1 X 2
Oxygen control 2 X 3, 4
Condensate control 2 X 3, 4
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-11 / 15
Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 31
Product name / method: One Shot
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT One Shot 3, 3a, 3b X 1
1, 2, 3
Alkalinity control 3, 3a, 3b X 1, 3, 4
(Hydrazine) 2, 2a, 2b X 1, 3, 4

Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 32
Product name / method: One Shot
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
BWT One Shot 1 X 2
1
Alkalinity control 2, 2a, 2b X 3, 4
(Hydrazine) 2, 2a, 2b X 3, 4

Chemical injection points (continued)
Manufacturer / supplier: Uniservice Group
Table No. 33
Product name / method: Organic Treatment
Chemical name Injection point No. Continuous Batch Note No. Valid flow diagram No.
OBWT 3 3, 3a, 3b X 1
1, 2, 3
OBWT 4 2, 2a, 2b X 1, 3, 4


Table 2
FEED AND BOILER WATER OM9210_99#B.1
9-12 / 15 Language UK
Flow diagram No.: 1
Boiler
PT
3
2
1
Condenser
Service
steam
Steam
dump
valve
Cooling
water
Hot well
Condensate
Make-up
Overflow
Drain
PI PI
PI PI
PS
Feed water
pumps
Single boiler operation with or without
forced circulation exhaust gas boiler
Figure 1 om9210_99_flowdix0060010en.wmf
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-13 / 15
Flow diagram No.: 2
Boiler
PT
3a
2a
1
Condenser
Service
steam
Steam
dump
valve
Cooling
water
Hot well
Condensate
Make-up
Overflow
Drain
PI PI
PI PI
PS
Boiler
3b
2b
PI PI
PI PI
PS
Feed water
pumps
Feed water
pumps
Double boiler operation with separate feed water pumps
with or without forced circulation exhaust gas boiler
Figure 2 om9210_99_flowdix0060020en.wmf
FEED AND BOILER WATER OM9210_99#B.1
9-14 / 15 Language UK
Flow diagram No.: 3
Boiler
PT
3a
2a
1
Condenser
Service
steam
Steam
dump
valve
Cooling
water
Hot well
Condensate
Make-up
Overflow
Drain
PI PI PS
Boiler
3b
2b
PI PI
Feed water
pumps
PI PI
PS
PS
Double boiler operation with common feed water pumps
with or without forced circulation exhaust gas boiler
Figure 3 om9210_99_flowdix0060030en.wmf
FEED AND BOILER WATER OM9210_99#B.1
Language UK 9-15 / 15
Table of contents
Water level gauge
Description Document ID Page
.
Water level gauge...................................................... OM7010_02.............. 10-2
TABLE OF CONTENTS
Language UK 10-1 / 5
Water level gauge
1 Maintenance and service instructions
This section describes the maintenance and service instructions for the water level
gauge.
Illustration of the water level gauge
S 2 1 2 1 3 4
W
2 1
D 8
7 G
6 5
1 Nuts
2 Stuffing box head
3 Union nut
4 Connection tube
5 Bolts
6 Nuts
7 Bulb
8 Joint ring
S Cock
W Cock
G Gauge body
D Drain cock
Figure 1 om7010_02_levelix0057020en.wmf
1.1 Maintenance
The item numbers mentioned in the following section refer to Figure 1.When the boiler
is out of service and the gauge body is in cool and depressurised condition the bolts
(5) and nuts (6) can be re-tightened.
WATER LEVEL GAUGE OM7010_02#A.2
10-2 / 5 Language UK
Illustration of tightening sequence
9 8
5 4
1 2
3 6
7 10
Figure 2 om7010_02_levelix0057050en.wmf
Step A: Start at the centre, working to the opposite sides alternately. Max torque is45
Nm.
1.1.1 Maintenance during service check-up
Step A: Check and tighten the nuts (1) and union nuts (3).
Step B: Check and tighten the bolts on the boiler flanges.
Step C: Check and tighten the nuts on the cocks (S) and (W). Please note that this
should be done with the cocks in open position.If a leak cannot be stopped
by tightening the nuts, the sealing surface of the cock plug may be damaged
or corroded. It might also be necessary to change the packing (8).
1.2 Blowing down
The item numbers mentioned in the following section for blowing down procedures
refer to Figure 1.
Step A: The water level gauge should be blown down before starting up the boiler,
before stopping the boiler, and according to the maintenance instructions.
1.2.1 Cleaning the water side:
Step A: Close the cock (S) and open the cock (W).
Step B: Open the drain cock (D) for a short time. This sucks out the water of the
glass without, however, totally depressurising the gauge body.
Step C: Close the drain cock (D)again and the water is forced upwards into the glass.
Step D: Repeat this procedure several times,opening and closing the drain cock (D).
The water level in the glass rises and falls.
1.2.2 Cleaning the steam side:
Step A: Close the cock (W) and open the cock (S).
Step B: Blow through the steam side and gauge body by opening the drain cock (D)
for 1-2 seconds. Longer duration is not advisable considering the service life
of the glass.
Step C: Turn the cock (W)to operating position.
WATER LEVEL GAUGE OM7010_02#A.2
Language UK 10-3 / 5
1.3 Dismantling and assembling
The following dismantling instructions refer to Figure 1, Figure 2 and Figure 3. Ensure
that the boiler is depressurised before proceeding with the work procedures.
Step A: Close the cocks (S) and (W).
Step B: The drain cock (D)must be opened until the glass is completely emptied.
Step C: Disconnect the electric power.
Step D: Remove the nuts (1) and lift off the stuffing box heads (2) together with the
gauge body (G) from the cocks (S) and (W).
Step E: Slacken the union nuts (3) and pull off the stuffing box heads (2) from the
connection tubes (4).
Step F: Place the gauge body (G) in a suitable position and unscrew the nuts (7a),
see Figure 3.
Step G: Remove the bonnets (2a), sealing gaskets (3a), transparent glasses (5a),
cushion gaskets (6a), and body (4a).
Step H: Clean all surfaces and examine the gaskets for through going scars. Replace
the gaskets if necessary.
Step I: Assemble the water level gauge in reverse order.
Step J: Tighten the bolts (1a) and nuts (7a) evenly. Start at the centre, working to
the opposite sides alternately. Max torque is 45Nm see Figure 2.
Step K: Assemble the stuffing box head (2) on the connection tubes (4) of the gauge
body (G). Insert joint rings (8) in the recesses of each cock (S) and (W).
Step L: Press the stuffing box heads (2) together with the gauge body (G) on the
gauge cocks (S) and (W).
Step M: Tighten the nuts (1) to form a pressure tight seal.
Step N: Turn the gauge body (G) to the required position and tighten union nuts (3).
Step O: Open the cocks (S) and (W). Close the drain cock (D).
Step P: Connect the electric power.
Step Q: When the boiler is started again and normal working pressure has been
reached re-tighten the bolts (1a) and nuts (7a) once again.
Sectional view of the water level gauge
1a 2a 3a 4a 5a 6a 7a
1a Bolt
2a Bonnet
3a Sealing gasket
4a Body
5a Transparent glass
6a Cushion gasket
7a Nut
Figure 3 om7010_02_levelix0057030en.wmf
WATER LEVEL GAUGE OM7010_02#A.2
10-4 / 5 Language UK
1.4 Maintenance of the gauge cock
The cock plug (7b) is sealed with a packing sleeve (6b), see Figure 4. Should a leakage
arise during service the packing sleeve must be further compressed by means of the
tightening nut (8b) until the leakage is stopped. This should only be done with the cock
in open position.
Drawing of the gauge cock
1b 2b 3b 4b
5b
6b
7b
8b
1b Cock handle
2b Washer
3b Screw
4b Gauge cock body
5b Split ring
6b Packing sleeve
7b Cock plug
8b Tightening nut
Figure 4 om7010_02_levelix0057040en.wmf
1.4.1 Dismantling
Step A: When the boiler is depressurised unscrew the tightening nut (8b) and screw
(3b).Remove the washer (2b) and cock handle (1b).
Step B: Knock out the cock plug (7b) together with the split ring (5b) and packing
sleeve (6b) of the gauge cock body (4b) by means of a soft mandrel.
Step C: Remove the split ring (5b) and knock out the cock plug (7b) of the packing
sleeve (6b).
Step D: Clean all sealing surfaces carefully and lubricate threads with high temper-
ature grease before installation.
1.4.2 Assembly
Step A: Place the split ring (5b) in the recess of the cock plug (7b).Push a new pack-
ing sleeve (6b) onto the cock plug.
Step B: Press the complete unit into the gauge cock body (4b).
Note: Turn the packing sleeve (6b) until the ridge fits with the groove in the gauge
cock body (4b). The eyelets of the packing sleeve must neither protrude
nor be tilted.
Step C: Screw in the tightening nut (8b).Place the cock handle (1b) and washer (2b)
on the plug and fit screw (3b).Tighten the tightening nut (8b) and check if
the plug can be turned.
WATER LEVEL GAUGE OM7010_02#A.2
Language UK 10-5 / 5
Table of contents
Safety valves
Description Document ID Page
.
Safety valves............................................................. OM6040_01.............. 11-2
Temporary locking of a safety valve............................ OM6040_02.............. 11-6
TABLE OF CONTENTS
Language UK 11-1 / 7
Safety valves
1 General
In the following the measures required to achieve a safe and reliable operation as well
asmaintenance of the safety valves will be described, together with adjustment and
dismantling instructions.An installation example of the safety valve is shown in Fig-
ure 1.
Mounting of safety valves, example
Expansion joint
with sealing ring
Support
Drain
Drain
Waste steam pipe
Drain
If safety valve DN50/80
drain connection is G1/4" BSP
If safety valve DN65/100
drain connection is G3/8" BSP
=
=
Figure 1 om6040_01_safe_0x0056591en.wmf
2 Maintenance and start-up of boiler
A regular inspection of the safety valve is recommended at least once a year. Some
media and appliances require a more frequent inspections, this is according to the
experience of the supplier.
SAFETY VALVES OM6040_01#A.2
11-2 / 7 Language UK
Warning: Prior to any handling and dismantling of the safety valve ensure that
the system is depressurised.
Before lighting-up the boiler, pipe connections must be thoroughly cleaned for dirt and
foreign bodies.If the valve is not completely tight, which often is the case after start
up of the plant, this is usually caused by impurities between the seat and the cone. In
order to remove these impurities the valve must be heavily blown out by means of the
lifting device. If the valve is not tight after several blows, it may be due to the fact that
a hard foreign body has got stuck between the cone and the seat, and it will then be
necessary to dismount the valve for overhaul.
Warning: In case of a leaking safety valve the valve must be inspected and over-
hauled as soon as possible. It must be ensured that the boiler is totally
depressurised before dismounting the valve.
Note: Before dismantling the safety valve in the workshop the position of the
adjusting screw must be measured and noted which will facilitate the ad-
justment later when the valve is to be adjusted when in service.
In case the facings between the cone and the seat have been damaged, they must be
grinded.
Step A: The cone can be grinded against a cast iron plate, using a fine grained car-
borundom stirred in kerosene.
Step B: The seat in the valve body can be grinded in the same way by using a cast
iron punch of suitable size.
Note: Never use the cone itself when grinding the seat.
Warning: The spindle and the valve cone must always be secured against turning
as the seat and the cone may thus be damaged.
Step C: Before assembly the valve must be thoroughly cleaned, and all traces of
grinding material and impurities must be removed.
Step D: When the valve has been mounted and the boiler is commissioned, the valve
must be checked for leakage and adjusted to the set pressure.
Step E: The adjustment screw is secured by means of its lock nut, and the valve is
sealed.
2.1 Routine check
The following should be regarded as recommendations of routine checks on the safety
valves, in order to secure a correct function:
SAFETY VALVES OM6040_01#A.2
Language UK 11-3 / 7
Monthly
Step A: Examine the safety valves for any leaking, such as:
- Is water seeping from the drain plug at the valve body?
- Is the escape pipe hot due to seeping steam from the valve seat?
Step B: Examine the drain and expansion device at the escape pipe.
Step C: Examine the lifting gear device, i.e. clean up and grease all sliding parts.
Yearly
Step A: The safety valve should be tested in operation by raising the boiler pressure.
Step B: Expansion and exhaust pipe should be examined at the same time.
3 Adjustment and dismantling
Safety valves are delivered with the required spring setting and sealed against unau-
thorised adjustment.Adjustments are only allowed in the spring margins. Outside the
margin a new spring is required. The pressure in a system should not exceed 90% of
the set pressure.
All item numbers mentioned in the following sections refer to Figure 2.
3.1 Dismantling of lifting device
Safety valve with open cap:
Step A: Remove bolt(39) and remove lift lever (41)
3.2 Set pressure change without spring change
Note: Pay attention to spring range.
Step A: Spindle (14) must be held fast by all alterations.
Step B: Loosen lock nut (21).
Step C: Turn the adjusting screw (17) clockwise for higher and anticlockwise for
low set pressures.
Step D: Secure the new setting with the lock nut (21) and reassemble lifting device.
3.3 Spring change
Step A: Spindle (14) must be held fast by all alterations.
Step B: Loosen lock nut (21) and turn adjusting screw (17) anticlockwise, then the
spring (37) is not under tension.
Step C: Loosen the nuts (8) and remove the bonnet (42).
Step D: Remove the upper spring plate (26), spring (37), spindle (14) with disc (12),
guide plate (4), and lower spring plate (26).
Step E: Clean the seat (2) and disc (12).
Step F: Remount the spindle unit with the new spring and upper spring plate.As-
semble bonnet (42) and adjust to the spring range.
SAFETY VALVES OM6040_01#A.2
11-4 / 7 Language UK
Step G: Secure the spring setting through the lock nut (21) and remount lifting de-
vice.
Assembling drawing of safety valve
47 Ball
42 Bonnet
41 Lifting lever
40 Split pin
39 Bolt
38 Screw
37 Spring
29 Cap
27 Gasket
26 Springplate
23 Lead seal
22 Drain screw
21 Lock nut
18 Ball
17 Adjusting screw
16 Slotted pin
15 Gasket
14 Spindle
13 Lift aid
12 Disc
10/25 Split cotters
9 Lift limitation ring
8 Hex. nut
7 Gasket
4 Spindle guide
3 Stud
2 Seat
1 Body
17
37
14
10, 25
8
16
18
12
13
15, 22
2
1
23
26
39, 40
41
29
38, 47
42
27
21
Figure 2 om6040_01_safe_0x0056600en.wmf
SAFETY VALVES OM6040_01#A.2
Language UK 11-5 / 7
Temporary locking of a safety valve
1 General
During commissioning work or later tests of the opening pressure for the safety valves,
only one safety valve should be checked at a time. This means that the other safety
valve must be locked. The following instruction describes the temporary locking of a
safety valve.
1.1 Procedure for locking of a safety valve
Step A: Remove the bolt (39) and split pin (40), see Figure 1.
Step B: Remove the lifting lever (41).
Step C: Unscrew the screw (38) and break the lead seal (23), if provided.
Step D: Unscrew the cap (29).
Step E: Place one or two bolts (48) on top of the spindle. The height of the bolts
should be approximately 1-2 mm higher than the normal distance between
the top of the spindle and the inside top of the cap (29).
Step F: Carefully screw on the cap until the spindle and bolts are locked. The safety
valve will be completely locked when the bolts cannot be moved anymore.
Step G: The other safety valve can now be tested without any interference from the
locked safety valve.
1.2 Procedure for unlocking of a safety valve
Warning: As soon as the test procedure for the safety valve has been carried out
the locked safety valve must be unlocked.
Step A: Unscrew the cap (29) and remove the bolts (48).
Step B: Mount the cap (29) again and screw in the screw (38).
Step C: Mount the lifting lever (41), bolt (39), and split pin (40).
Step D: Provide the safety valve with a lead seal (23), if necessary. This depends on
the local rules of the classification society.
TEMPORARY LOCKING OF A SAFETY VALVE OM6040_02#A.2
11-6 / 7 Language UK
Temporary locking of a safety valve
23
39, 40
41
29
38
48
Figure 1 om6040_02_safe_0x0056610en.wmf
TEMPORARY LOCKING OF A SAFETY VALVE OM6040_02#A.2
Language UK 11-7 / 7
Table of contents
Feed water system
Description Document ID Page
.
Water level control.................................................... SD9230_12............... 12-2
Safety device............................................................. OM8210_04.............. 12-3
Water level control system.......................................... OM8210_13.............. 12-9
TABLE OF CONTENTS
Language UK 12-1 / 14
Water level control
1 Description
The water level control is a modulating system at this type of boiler. The system is
illustrated in Figure 1. The system consists of one independent safety device electrode
for too low water level shut down and burner stop. For measuring and control of the
water level, one capacitance level electrode is provided, and it is used to give water
level alarms/shut downs and control of the regulating feed water valve.
Water level control system
Boiler
Feed water pumps
Control
system
(panel)
Feed water
valves
LW
NW
HW
Water level control system
Flange
Electrode stand
Vent hole
Compact system
(level transmitter
and level electrode)
Safety device
Protection tube
Regulating feed water valve
Instrument air
Figure 1 sd9230_12_ges_1_x0063950en.wmf
WATER LEVEL CONTROL SD9230_12#A.2
12-2 / 14 Language UK
Safety device
1 General
The safety device consists of a level electrode and a level switch. The level electrode
is mounted in an electrode stand on top of the boiler, and the level switch is placed
inside the control system. Depending on the rules of the classification society, the boiler
can be provided with one or two sets of safety devices. The function of the safety device
is to continuously supervise the water level in the boiler and subsequently give a shut
down and cut out of the burner if the water level is too low.
The combination of a level electrode NRG 16-11 and a level switch NRS 1-7b provides
a fail-safe protection against a first fault, i.e. the system will still continue to provide
the safety function even after a first fault.
The self-monitoring design ensures an interruption of the burner circuit in case of a
failure of the electrode, supply cables, level switch, or in the power supply.
The safety device has a built-in response delay, which is indicated on the name plate.
This eliminates unintentional cut-out of the burner circuit caused by interference from
splash, level fluctuations, etc.
2 Level electrode
2.1 Operation
The too low level electrode operates on the conductive measuring principle using the
electrical conductivity of the boiler water for level signalling. An illustration of the
level electrode type NRG 16-11 is shown in Figure 1. The length of the electrode is
adjusted to the correct length before mounting in the electrode stand.
In normal operation the electrode tip is submerged in the water, and the imbalance of
the bridge circuit is positive. If the water level is below the electrode tip or in case of
a fault, the electrode produces a negative imbalance of the bridge circuit provided in
the level switch (NRS 1-7b). This produces the too low level shut down signal and
consequent cut-out of the burner circuit.
The level electrode consists of two single electrodes (measuring electrode and com-
pensating electrode), which are concentrically arranged and insulated from each other
by special insulating seals. The electric connection of the two electrodes is effected
coaxially with a tube, contact ring, and stud. A system of compression springs in the
SAFETY DEVICE OM8210_04#A.2
Language UK 12-3 / 14
electrode body ensures sufficient sealing forces at the insulating seals, even if the
temperatures vary. The stud is insulated by a Teflon foil. PTFE insulated wires connect
the contact ring and body to the terminal block.
If the insulating seals placed between the electrodes and body are no longer tight due
to deterioration caused by mechanical or chemical breakdown, liquid will penetrate
into the cavities between the body, tube, and stud. This produces a strong negative
imbalance of the bridge circuit, which causes a too low level shut down signal. But in
this case the signal is due to a malfunction. This means that the water level in the boiler
must be checked in the water level gauges if the level switch signals an shut down.
Level electrode type NRG 16-11
Figure 1 om8210_04_nrg16-x0058280en.wmf
2.2 Cleaning/exchanging the electrode
The following work procedures must be carried out if the level electrode is cleaned or
replaced:
Dismantling:
Step A: Stop the boiler plant according to the separate instructions for start/stop of
the boiler.
Warning: When the level electrode is loosen, steam or hot water might escape.
This presents the danger of severe injury. It is therefore essential not
to dismantle the level electrode unless the boiler pressure is zero.
Step B: Disconnect the wires for the compact system and safety device.
Step C: Unscrew the bolts on the flange for the compact system and safety device.
SAFETY DEVICE OM8210_04#A.2
12-4 / 14 Language UK
Step D: Pull out the flange including the compact system and safety device from the
electrode stand.
Step E: Unscrew the locking screw, which locks the level electrode to the flange.
Step F: Unscrew the level electrode from the flange by means of a 36 mm ring
spanner.
Step G: Pull out the level electrode from the flange and electrode holders.
Cleaning:
Note: The interval for cleaning of the electrode rod depends on the present boiler
water conditions. Therefore an exact time interval cannot be given.
Step A: Clean the rod of the level electrode with a wet cloth.
Replacing the level electrode:
Step A: Exchange the defect level electrode.
Replacing the electrode tip:
Step A: Screw the electrode tip "D" into the measuring electrode "A", see Figure 2.
Step B: Carefully determine the required measuring length and mark the length of
the electrode tip "D".
Step C: Unscrew the electrode tip "D" from the measuring electrode "A" and cut the
tip. If provided with a PTFE insulation this must be cut min. 150 mm above
the electrode tip and fixed with a starlock washer.
Step D: Screw the electrode tip "D" into the measuring electrode "A" and tighten.
Slide the spring "C" along the electrode tip "D" so that its bend end com-
pletely enters into the small bore "B".
Assembling:
Step A: Check the seating surfaces of the level electrode thread and flange, see
Figure 1.
Step B: Place the joint ring "K" onto the seating surface "J" of the level electrode.
Use only a joint ring (stainless steel) D 27 x 32.
Step C: Apply a light smear of silicone grease (e.g., DOW Corning 111 compound)
to the level electrode thread "I".
Attention: Do not insulate the electrode thread with hemp or PTFE tape.
Step D: Screw the level electrode into the flange and electrode holders. The torque
required is 160 Nm (when cold).
Step E: Screw the locking screw into the level electrode.
Step F: Check the seating surfaces of the electrode stand flange and level electrode
flange. Place a flat gasket on the electrode stand flange.
Step G: Place the flange including the compact system and safety device onto the
electrode stand flange. Fix the flanges with bolts and tighten the bolts in
diagonally opposite pairs.
Step H: Connect the wires for the compact system and safety device.
SAFETY DEVICE OM8210_04#A.2
Language UK 12-5 / 14
Assembling of the NRG 16-11 level electrode
Figure 2 om8210_04_nrg16-x0058290en.wmf
3 Level switch
3.1 Operation
The level switch is a two-channel unit provided with an automatically self-checking
circuitry. The level switch of type NRS 1-7b is illustrated in Figure 3, and the wiring
diagram can be seen in Figure 4.
The green LED indicates mains on. Two red LEDs indicate the shut down states too
low level or malfunction of the system. A single red LED signals the failure of one
channel (loss of redundancy).
The self-checking circuitry is effected periodically. The test includes the checking of
the cable between the level electrode and level switch and also of the self-checking
circuitry (redundancy). The output relays are not influenced by the internal tests.
As the circuit of the relay contacts is normally closed, a shut down will also be signalled
in the event of a mains failure. The level switch can signal the following three operating
conditions:
- Normal operation: correct level
- Shut down: too low level
- Shut down: defect in the level switch or electrode
SAFETY DEVICE OM8210_04#A.2
12-6 / 14 Language UK
Level switch type NRS 1-7b
Figure 3 om8210_04_nrs1-7x0058300en.wmf
3.2 Performance tests
Live test:
Step A: Decrease the water level in the boiler by means of the blow-down valves
until the water level has fallen below the too low level mark.
Step B: After the response delay indicated on the name plate, the two red LEDs on
the level switch must light up. If the burner is running, it will immediately
be stopped or if it is stopped, it will be blocked from operation.
Note: Should the too low level point be reached during a self-checking cycle, this
cycle must first be completed. Only then the alarm system will enter its
own delay period. Thus the total maximum delay of twice the nominal delay
period may occur.
Test 1:
A too low level shut down can be simulated by pushing the button "TEST 1" whilst
the electrode tip is submerged in water. This test should be carried out with frequent
intervals.
Step A: Push the button "TEST 1" until the response delay has expired. Both red
LEDs must light up.
Test 2/inspection:
The checking circuitry of the level switch can also be checked. This test must, as a
minimum be carried out at least once every year.
Step A: Operate the switch "TEST 2/INSPECTION" in the direction of the arrow
with the electrode tip submerged in water (above the too low level mark).
Step B: After maximum two minutes the two red LEDs must signal too low level
shut down.
SAFETY DEVICE OM8210_04#A.2
Language UK 12-7 / 14
Note: The button "TEST 1" must not be operated during this test nor must the
water level fall below the too low level mark.
Step C: Return the switch into its original position after the test. After the response
delay the two red LEDs must extinguish.
3.3 Fault finding
Fault finding scheme
Fault Remedy
The level switch signals too low level shut down
before the water level in the boiler has fallen below
the too low level mark.
Measure the conductivity of the boiler water.
Check the wiring of the level switch and electrode.
Check the length of the electrode tip.
After raising the water level above the too low
level mark, the two red LEDs on the level switch
are not extinguished or only after a considerable
period.
Check whether a vent hole has been provided in
the electrode stand.
One or both red LEDs on the level switch light up
without the water level has fallen below the too
low level mark.
This means that an electronic failure within the
level switch has occurred, i.e. failure of one or two
of the channels. In this case replace the level
switch.
The test with the switch "TEST 2/ INSPECTION"
was not successful, i.e. only one red LED or none
of the two red LEDs lighted up two minutes after
the start of the test.
Replace the level switch.
Table 1
Wiring diagram
Figure 4 om8210_04_nrs1-7x0058310en.wmf
SAFETY DEVICE OM8210_04#A.2
12-8 / 14 Language UK
Water level control system
1 General
The compact system of type NRGT 26-1 consists of a level electrode, protection tube,
and level transmitter. Via a flange the level electrode is inserted in an electrode stand
mounted on top of the boiler. Inside the electrode stand the protection tube is connected
to the flange and surrounds the level electrode. The integrated level transmitter is
placed on top of the level electrode. Figure 1 illustrates the compact system of type
NRGT 26-1. In the first illustration the compact system is shown without the protection
tube and flange. The flange shown in the second illustration can be of a different type.
The compact system works according to the capacitance measurement principle and
is used for signalling different water levels in the boiler. The electrode rod and pro-
tection tube form a capacitor. If the level of the dielectric (boiler water) located between
the two capacitor plates changes, the current which flows through the plates changes
proportionally to the level. The level transmitter produces a standard analogue output
of 4-20 mA, which is sent to the control system. Figure 2 illustrates the level transmitter.
Compact system type NRGT 26-1
Figure 1 om8210_13_nrgt26x0058440en.wmf
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
Language UK 12-9 / 14
Compact system type NRGT 26-1 (level transmitter)
Figure 2 om8210_13_nrgt26x0058430en.wmf
Table for position numbers illustrated in Figure 1 and Figure 2
A Electrode thread 3/4" BSP, DIN 228 J Measuring range switch
B Sealing surface K Potentiometer for lower measuring point
C
Joint ring (of stainless steel) D 27 x 32 to
DIN 7603
L Red LED "level 0%"
M Green LED "level > 0%, < 100%"
D Flange (different ones are used) N Red LED "level 100%"
E Protection tube O Potentiometer for upper measuring point
F Spacer disc P Thermal fuse Tmax 102C
G Housing screw M 4 Q Terminal strip
H Cable entry PG 9 / PG 16 R PE connection
I Housing cover S Screw
Table 1
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
12-10 / 14 Language UK
2 Cleaning/exchanging the electrode
The following work procedures must be carried out if the level electrode is cleaned or
replaced:
Dismantling:
Step A: Stop the boiler plant according to the separate instructions for start/stop of
the boiler.
Warning: When the level electrode is loosen, steam or hot water might escape.
This presents the danger of severe injury. It is therefore essential not
to dismantle the level electrode unless the boiler pressure is zero.
Step B: Disconnect the wires for the compact system and safety device.
Warning: The terminal strip and the electronic components of the NRGT 26-1
are live during operation. This presents the danger of electric shock.
Cut off the power supply before fixing or removing the housing cover.
During commissioning use only completely insulated spanner for ad-
justing the measuring points.
Step C: Unscrew the bolts on the flange for the compact system and safety device.
Step D: Pull out the flange including the compact system and safety device from the
electrode stand.
Step E: Unscrew the locking screw, which locks the level electrode to the flange.
Step F: Unscrew the level electrode from the flange by means of a 41 mm open-end
spanner.
Step G: Pull out the level electrode from the flange and protection tube.
Cleaning:
Note: The interval for cleaning of the electrode rod depends on the present boiler
water conditions. Therefore an exact time interval cannot be given.
Step A: Clean the rod of the level electrode with a wet cloth.
Replacing:
Step A: Exchange the defect level electrode including the level transmitter.
Assembling:
Step A: Check the seating surfaces of the level electrode thread and flange.
Step B: Place the joint ring "C" onto the seating surface "B" of the level electrode
(see Figure 1). Use only a joint ring (stainless steel) D 27 x 32.
Step C: Apply a light smear of silicone grease (e.g., DOW Corning 111 compound)
to the level electrode thread "A".
Attention: Do not insulate the electrode thread with hemp or PTFE tape.
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
Language UK 12-11 / 14
Step D: Screw the level electrode into the flange and protection tube. The torque
required is 160 Nm (when cold).
Step E: Screw the locking screw into the level electrode.
Step F: Check the seating surfaces of the electrode stand flange and level electrode
flange. Place a flat gasket on the electrode stand flange.
Step G: Place the flange including the compact system and safety device onto the
electrode stand flange.
Step H: Fix the flanges with bolts and tighten the bolts in diagonally opposite pairs.
Step I: Connect the wires for the compact system and safety device. A wiring dia-
gram for the compact system can be seen in Figure 3.
Wiring diagram
1 2 3 4 5 6 7
4-20 mA
Mains
L N PE
2
3
0

V
o
r
1
1
5

V
2
4

V
Figure 3 om8210_13_nrgt26x0058420en.wmf
3 Standard setting
The purpose of the switch "J" is to set the optimal frequency band for the internal
measurement inside the compact system. To obtain the best measuring conditions, the
switch "J" is set to a position determined by the active measuring length of the level
electrode. The compact system is delivered with the following factory settings:
- Measuring range 275 mm: switch "J" position 3, water > 20 S/cm
- Measuring range 375 mm to 675 mm: switch "J" position 4, water > 20 S/cm
- Measuring range 775 mm to 1375 mm: switch "J" position 5, water > 20 S/cm
- Measuring range 1475 mm to 1975 mm: switch "J" position 6, water > 20 S/cm
4 Commissioning
Wiring check:
Step A: Check that the system has been wired according to the wiring diagram (see
Figure 3 and the electrical drawings).
Step B: Check that the mains supply corresponds to the value shown on the label of
the equipment.
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
12-12 / 14 Language UK
Application of mains voltage:
Step A: Unscrew the screws "G" and remove the housing cover "I".
Step B: Apply mains voltage. The LED "L" will light up (see the position in Fig-
ure 2).
Adjustment of the lower measuring point:
Step A: Fill the boiler with water until the lower measuring point is reached.
Step B: Start the boiler according to the separate instructions for start/stop of the
boiler.
Step C: Raise the boiler pressure till normal working pressure.
Step D: Turn the potentiometer "K" to the left. The red LED "L" lights up.
Step E: Turn the potentiometer "K" to the right until only the green LED "M" lights
up.The lower measuring point is now adjusted.
Adjustment of the upper measuring point:
Step A: Fill the boiler with water until the upper measuring point is reached.
Step B: Operate the burner until the boiler pressure has reached normal working
pressure.
Step C: Turn the potentiometer "O" to the right until only the red LED "N" lights
up.
Step D: Turn the potentiometer "O" to the left until the green LED "M" lights up.
Step E: Turn the potentiometer "O" to the right until the green LED "M" extin-
guishes.
Step F: Mount the housing cover "I" and screw in the screws "G".The upper meas-
uring point is now adjusted.
Note: When adjusting the measuring points of the electrode in a cold boiler, the
measuring points will shift with rising temperature as a result of the lon-
gitudinal expansion of the electrode rod. The adjustment must be corrected
proportionally.
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
Language UK 12-13 / 14
5 Fault finding
Fault finding chart
Fault Remedy
The equipment does not work
Mains voltage has not been applied. Apply mains voltage. Wire the equipment according to the wir-
ing diagram.
The thermal fuse has failed. In the case of a defective thermal fuse, the mains voltage has not
been connected to terminal "Q". Replace the defective thermal
fuse.
The ambient temperature must not exceed 70C.
The electrode housing does not have earth connection to the
boiler.
Clean the seating surfaces and insert the metal joint ring (of
stainless steel) 27 x 32 to DIN 7605.
Do not insulate the compact system with hemp or PTFE tape.
The electronic board is defective. Replace the board.
The equipment does not work accurately
The electrode has been installed without the protection tube. The
protection tube serves as reference electrode.
Install the protection tube.
The vent hole in the protection tube does not exist, is obstructed,
or flooded.
Check the protection tube and, if necessary, provide a vent hole.
The desired zero point does not lie within the measuring range
of the electrode. The electrode is too short.
Replace the compact system. Choose an adequate electrode
length.
The adjustment of the measuring range is wrong. Adjust switch "J" correctly (see the instructions).
Dirt deposits have been accumulated on the electrode rod. Remove the compact system and clean the electrode rod with a
wet cloth.
The gasket of the electrode rod is damaged. Measure the current
at terminal 1 and 2 (>20 mA).
Replace the compact system.
Table 2
WATER LEVEL CONTROL SYSTEM OM8210_13#A.2
12-14 / 14 Language UK
Table of contents
Regulating feed water valve
Description Document ID Page
.
Control valves, type 470/471....................................... OM6010_02.............. 13-2
Pneumatic actuator, type dp........................................ OM5520_01.............. 13-7
Positioner, SIPART PS2 6DR5000.............................. OM5510_05.............. 13-14
TABLE OF CONTENTS
Language UK 13-1 / 30
Control valves, type 470/471
1 General
This type of control valve is suited to regulate fluids, gases and steams. The valve plug
is normally a parabolic plug, but can also be supplied in a perforated design. Both types
of plugs can have either linear or equal percentage flow characteristic.
The flow direction for parabolic plugs is always against the closing direction. However,
with perforated plugs for steam and gases, it is in the closing direction. If a valve with
a perforated plug is operated by means of a pneumatic actuator with the flow in the
closing direction, the pneumatic actuator should have a stronger thrust force. This is
necessary to prevent thumping near to the closing position.
All control valves can be fitted alternately with manual-, pneumatic-, electric- or hy-
draulic operation devices.
Illustration of control valves type 470 and 471
Figure 1 om6010_02_val47xx0056570en..wmf
CONTROL VALVES, TYPE 470/471 OM6010_02#A.2
13-2 / 30 Language UK
Table of position numbers in Figure 1
Part Designation Part Designation Part Designation
1 Body 7 Gland flange 15.1 Studs
2 Seat ring 7.1 Screw joint 17 Hexagon nuts
3 Mounting bonnet 8 Spindle guiding 17.1 Hexagon nuts
3.1 Mounting bonnet 10 Stuffing box 19 Spring-type straight pin
4 Guiding bush 10.1 Stuffing-box packing 21 Set-pin
5 Plug 14 Gasket 25 Bellow housing
6 Spindle 14.1 Gasket 26 Bellow unit
6.1 Spindle 15 Studs
Table 1
2 Operation
2.1 Fitting instructions
The valve should be inserted so that the spindle has a vertical position together with
the actuator. The valve can also be tilted to a maximum horizontal position if the
installation point does not allow any better condition.
To guarantee a disturbance free function of the control valve, the inlet and outlet
stretches of the piping should be of straight piping length (min. two times the pipe
diameter by inlet and six times by outlet). The piping should be rinsed to clear out any
pollution, welding beads, rust, etc. before inserting the control valves. A strainer should
be fitted in front of the control valve to catch the remaining particles. Bolts should be
tightened after taking into operation.
The flow direction is signalled by an arrow on the valve body. The valves should be
insulated against high temperatures to guard the actuator.
2.2 Actuator assembly
The control valves are normally delivered with actuators already fitted. For alternations
or maintenance of actuator, the assembly should occur in accordance with the operation
instructions for the actuator.
2.3 Setting into operation
When the piping system is filled, the spindle sealing should be checked for leakage
and, if necessary, tightened. A PTFE-V-ring unit does not require any tightening as
the spring tension maintains the necessary force.
The bolts must be tightened gradually in steps, diametrically in pairs, but not tighter
than it is necessary for the sealing. Flange connection bolts should never be loosened
or tightened when the valve is under temperature or pressure even if a leakage may
arise.
CONTROL VALVES, TYPE 470/471 OM6010_02#A.2
Language UK 13-3 / 30
For actuators please see to the appropriate actuator operation instructions.
3 Maintenance
Before any maintenance of the control valve is carried out, the piping system must be
shut off and pressure free.
3.1 Exchange of the stuffing-box packing
A leak stuffing-box packing should initially be carefully tightened to stop the leakage.
If this does not help, a new layer should be inserted, or the complete packing should
be replaced.
3.1.1 Additional packing layer
Step A: Open the valve fully and unscrew the hexagon nuts (17).
Step B: Lift the gland flange (7) and the spindle guiding (8) upwards.
Step C: Insert adequate quantity of packing rings (split ring-displacement, splitting
at 180 to avoid overlapping).
Step D: Fix the hexagon nuts (17) properly.
3.1.2 Exchange
Step A: Drive the actuator into middle position and dismantle the actuator.
Step B: Unscrew the hexagon nuts (17) from the studs (15).
Step C: Remove the gland flange (7), the spindle guiding (8) and the old stuffing
box (10) and clean the packing compartment.
Step D: Clean the valve spindle and check for damage and if necessary replace. If
the damaged spindle is not replaced, the new packing will leak after a short
period.
Step E: Insert the new packing rings (split ring-displacement, splitting at 180 to
avoid overlapping).
Step F: Fix the hexagon nuts (17) properly.
Note: Strenuous tightening will prevent leakage, but will also have a brake effect
on the spindle which aggravates the movement of the spindle.
3.2 Exchange of a PTFE-V-ring sealing unit
A PTFE-V-ring unit is spring loaded and has enough set pressure to ensure a good seal
even by low operation pressures. It is replaced as mentioned above.
The PTFE-V-ring sealing unit should be lubricated before it is inserted. The sealing
lips must face against the pressure direction.
Note: Special care should be given to the spindle surface. Rough surfaces wear
the sealing lips enormously and can be due to failure of the packing unit.
CONTROL VALVES, TYPE 470/471 OM6010_02#A.2
13-4 / 30 Language UK
3.3 Exchange of the bellow unit
Step A: Drive the actuator into middle position and dismantle the actuator.
Step B: Unscrew the screw joint (7.1).
Step C: Unscrew the hexagon nuts (17) and remove the bellow housing (25). Dis-
mantle the plug as described in the next section.
Step D: Unscrew the hexagon nuts (17.1) and dismantle the mounting bonnet (3.1).
Step E: The bellow unit (26) is removed from the bellow housing (25).
Step F: Replace the two gaskets (14.1) and the gasket (14).
Step G: When the bellow unit (26) is replaced, the proper position of the anti-twisting
device must be observed.
Step H: The set pins (21) have to drive within the slots of the anti-twisting device.
Check for friction-free movement.
Step I: Replace mounting bonnet (3.1) and screw down the hexagon nuts (17.1)
crosswise.
3.4 Exchange of the plug-spindle unit
Step A: Drive the actuator into middle position and dismantle the actuator.
Step B: Unscrew the gland flange (7).
3.4.1 Control valve type 470
Step A: Unscrew the hexagon nuts (17) and dismantle the mounting bonnet (3).
Step B: Pull out the plug with the spindle and exchange this unit.
Step C: Remove the spring-type straight pin (19) and unscrew the spindle (6).
Step D: Replace the old parts and assemble it.
Step E: Drill a hole through the plug shaft and insert a new pin.
Step F: Replace the gasket (14) and assemble the mounting bonnet (3).
Step G: Tighten the nuts (17) evenly, crosswise.
3.4.2 Control valve type 471
Step A: Unscrew the hexagon nuts (17) and dismantle the bellow housing (25) with
plug (5).
Step B: Drive the spindle in the bottom position and remove the spring-type straight
pin (19).
Step C: Unscrew the plug.
Step D: Screw a new plug at the spindle and drill through the shaft. Drive the spring-
type straight pin (19) into the hole.
Step E: Replace the gasket (14).
Step F: Assemble the bellow housing (25) with plug (5) together with the body (1)
and fix it by screwing the hexagon nuts (17) crosswise.The spindle can only
be completely replaced together with the bellow.
3.5 Changing the seat ring
The seat ring is screwed into the valve body. The seat ring can be obtained after re-
moving the bonnet and can then be refinished or replaced as required.
CONTROL VALVES, TYPE 470/471 OM6010_02#A.2
Language UK 13-5 / 30
Step A: Clean and lubricate the thread and conical sealing surface before insertion.
CONTROL VALVES, TYPE 470/471 OM6010_02#A.2
13-6 / 30 Language UK
Pneumatic actuator, type dp
1 General
The pneumatic linear actuator is designed to be mounted directly on a control valve.
The pneumatic actuator converts positioning command signals into stem thrust forces.
The required back setting force is produced by the spring arrangement inside the ac-
tuator. The rolling-diaphragm produces linear spindle movements over the complete
stroke.
The preferred mounting position is with the actuator and valve spindle in vertical po-
sition.
The mode of operation for the actuator depends on how the springs are inserted when
the actuator is assembled. Even when the actuator is fitted in a piping system, the mode
of operation can be changed.
The pneumatic actuator can be operated as:

Spring opens valve/air closes valve operation mode

Air opens valve/spring closes valve operation mode

PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
Language UK 13-7 / 30
Illustration of a pneumatic actuator
Figure 1 om5520_01_dpactux0053610en.wmf
Table 1 below shows a list of the position numbers in Figure 1 and Figure 2.
Table of position numbers in Figure 1
Part Denomination Part Denomination
1 Rolling diaphragm 15 Stroke indicator
2 Diaphragm housing 16 Hexagon nut
3 Diaphragm lid 17 Mounting rod
4 Diaphragm plate 18 Bellow
5 Spindle 19 Collar nut
7 Spring 21 O-ring (spindle)
10 Coupling flange 22 O-ring (bushing)
11 Guide flange 26 Slotted guide bearing
12 Rotation guard 27 Spindle guide
13 Socket screw 30 Hexagon nut
14 Threaded bushing 31 Hexagon nut
Table 1
1.1 Pneumatic connection
The air supply should be dry and at a low service temperature. A heat-guard should be
installed to prevent high service temperature.
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
13-8 / 30 Language UK
The pneumatic supply tube must be connected to the diaphragm housing (2) by oper-
ation mode spring closes" and to the diaphragm lid (3) by operation mode spring
opens.
By air failure the stem automatically returns into the original position caused by the
inserted springs.
Warning: The actuator diaphragm may only be pressure loaded on the side op-
posite of the springs. The vent hole in the other connection must remain
open.
1.2 Assembly of the actuator on the valve
The assembling of the actuator on the valve is shown in Figure 2. For both spring
closes and spring opens operation modes the following assembling procedure
should be followed:
Step A: If the actuator and the valve are separated, press the plug and spindle unit
(5) into the closed position for operation mode spring closes or into the
open position for operation mode spring opens.
Warning: Make sure that the plug does not turn while pressing on the seat during
assembly.
Step B: Loosen the socket screws (13), remove the rotation guard (12) and the guide
flange (11). The threaded bushing (14) is now free.
Step C: Turn the locking hexagon nut (30) onto the valve spindle. Place the rotation
guard (12) and the guide flange (11) over the valve spindle and then turn the
threaded bushing (14) onto the valve spindle.
Step D: Check the actuator for proper operation mode and connect the pneumatic
supply to the connection piece in the diaphragm housing (2) for operation
mode spring closes or in the diaphragm lid (3) for operation mode spring
opens.
Step E: Drive the actuator into approximately mid-stroke position over the air supply
and mount it onto the valve (read the value from the pressure gauge - middle
of the spring range).
Step F: Tighten the hexagon nuts (31).
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
Language UK 13-9 / 30
Assembly of the actuator on the valve
Figure 2 om5520_01_dpactsx0053600en.wmf
1.3 Adjustment of the starting pressure signal
Step A: Drive the actuator to the required spring-starting point over the air supply.
Step B: Turn the threaded bushing (14) up against the coupling flange (l0) so that
the collar enters into the flange and presses against it. Make sure that the
plug is lying on the valve seat.
Attention: Note that sufficient thread of the valve spindle is inside the threaded
bushing (14). If not, turn the coupling flange (10) downwards from
the actuator spindle and pull the threaded bushing (14) against it.
Step C: For operation mode: spring closes:
- Attach the guide flange (11) and the rotation guard (12) with the socket
screws (13) to the coupling flange (10).
- Check that the plug lifts off the seat at the required spring starting point.
Step D: For operation mode: spring opens:
- Check that the plug leaves the end position at the required spring starting
point, and finishes the valve stroke at the spring-range end value.
- The plug must then also press on the valve seat.
Step E: After the test operation set the stroke indicators (15) into the end positions.
Step F: Lock the hexagon nuts (16 + 30) at the valve mid-stroke.
Step G: Do not turn the plug on the seat when it is under force.
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
13-10 / 30 Language UK
2 Reversal of the actuator action
The actuator action can be reversed even when the valve is installed in a piping system.
The position numbers mentioned in this section refer to Figure 1 and Figure 2.
Step A: Drive the actuator into approximately mid-stroke position with the air sup-
ply.
Step B: Loosen and remove the socket screws (13) from the coupling flange (10)
and drop the rotation guard (12) over the valve spindle.
Step C: Remove the hexagon nuts (31) from the actuator and lift off the valve.
Step D: Reduce the air supply until the chamber is pressure free.
Step E: Loosen and remove the diaphragm lid screws.
Step F: Remove the diaphragm lid (3).
Warning: The actuators DP 32 and DP 33 have two longer screws when fitted
with stronger spring ranges. The actuator DP 34 has four. These
screws should be the last screws to be loosened, and must be loosened
evenly to reduce the high spring tension.
Step G: For reversal from spring closes into spring opens:
- Remove the springs (7) and the diaphragm plate (4) with the diaphragm
(1) and the spindle (5).
- Loosen and remove the seal lock nut (19) and remove the spindle (5).
Turn over the diaphragm plate (4) with the diaphragm (1) and the dia-
phragm clamping flange, and place it over the spindle (5).
- Tighten with the seal lock nut (19). Make sure that the spindle surface
is not damaged.
- Grease the spindle surface and the 0-ring.
- Place the diaphragm plate (4) with the diaphragm (1) into the diaphragm
lid (3).
- Arrange the springs (7) onto the moulds pressed into the diaphragm plate
(4).
- Place the diaphragm housing with the spindle sealing unit over the spin-
dle, and screw it together. Make sure that the springs stay properly ar-
ranged.
- Turn the hexagon nut (16) and the coupling flange (10) onto the spindle
(5).
- Mount the actuator as described previously, and connect the air supply
tube to the diaphragm lid (3).
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
Language UK 13-11 / 30
Step H: For reversal from spring opens into spring closes:
- Remove the diaphragm (1) and the diaphragm plate (4) with the spindle
(5) and the springs (7).
- Loosen and remove the seal lock nut (19) from the spindle (5). Turn over
the diaphragm plate (4) with the diaphragm (1) and the diaphragm
clamping flange, and place it on the spindle (5).
- Tighten with the seal lock nut (19). Make sure that the spindle surface
is not damaged.
- Grease the spindle surface and the 0-ring.
- Stick the diaphragm plate (4) with the diaphragm (1) and the spindle (5)
into the diaphragm housing (2).
- Arrange the springs (7) onto the moulds pressed into the diaphragm plate
(4).Place the diaphragm lid (3) on the top, and screw it together. Make
sure that the springs (7) stay properly arranged.
- Turn the hexagon nut (16) and the coupling flange (10) onto the spindle
(5).
- Mount the actuator as described previously, and connect the air supply
tube to the diaphragm housing (2).
3 Manual operation device
Some actuators are fitted with a manual operation device. The device is connected to
the actuator by means of a new diaphragm lid, a spindle extension with a USIT-ring
and a spindle sealing unit.
The manual operation device is equipped with stroke indicators. The stroke indicators
of both the actuator and the manual operation device must be in the same end positions
when the actuator is pressure free.
The manual operation device must be set into neutral position when the actuator is
running automatically.
The locking device of the manual operation device must be unlocked before operating.
The locking device prevents an unwanted disarrangement of the setting during oper-
ation, e.g. due to vibration, etc.
4 Maintenance
The pneumatic actuator is maintenance free. To maintain a disturbance free operation,
the air should be supplied by an air-supply station.
The diaphragm, spindle sealing unit and springs are wear parts and should be replaced
when necessary.
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
13-12 / 30 Language UK
4.1 Exchange of spindle sealing
When the spindle sealing is changed, the slotted PTFE-guide bearing and the 0-ring
should be replaced. The spindle surface must be clean and undamaged. Before the
actuator is assembled, the spindle unit and the spindle must be greased.
PNEUMATIC ACTUATOR, TYPE DP OM5520_01#A.2
Language UK 13-13 / 30
Positioner, SIPART PS2 6DR5000
1 General
The following instruction is a general description of SIPART positioners and covers
the complete range in the PS2 6DR5000 series.
The electronic pneumatic positioner is used as the final control element of a pneumatic
linear actuator or a part-turn actuator (rotary movements). The positioner converts a
current output signal (4 to 20 mA) from a process controller or control system to a set
point value and into a corresponding movement. The positioner changes the pressure
in a pneumatic actuator chamber or cylinder until the position corresponds to the set
point value.
The positioner can be set up either as a single-action positioner or a double-action
positioner. The single-action positioner is mainly used together with a control valve.
The opposite movement for the control valve is supplied by means of springs. The
double-action positioner is mainly used to control an air damper via a pneumatic cyl-
inder (actuator). All movements of the pneumatic cylinder are supplied by the posi-
tioner. An illustration of the function diagram for the positioner is shown in Figure 1.
The function diagram is shown with option modules.
1.1 Mode of operation
Comparison of the set point and the actual value takes place electronically in a micro
controller. If the micro controller detects a deviation, it uses a 5-way switch procedure
to control the piezoelectric valves, which in turn regulate the flow of air into the ac-
tuating chambers. When connected in a two-wire system, the SIPART PS2 draws its
power exclusively from the 4 to 20 mA set point signal.
The piezoelectric valve converts the command into a pneumatic positional increment.
The positioner outputs a continuous signal in the area where there is a large control
deviation (high-speed zone). In areas of moderate control deviation (slow-speed zone)
it outputs a sequence of pulses. No positioning signals are output in the case of a small
control deviation (adaptive or variable dead zone).
Commissioning (initialisation) is carried out automatically to a large extend. During
initialisation, the micro controller automatically determines the zero, full-scale value,
direction of action, and positioning speed of the actuator. It uses these to determine the
minimum pulse time and dead zone, thus optimising the control.
The positioner can also be operated manually by the pushbuttons and the LCD of the
SIPART PS2.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-14 / 30 Language UK
The installation of the positioner must be carried out in the following order:

Mechanic connection

Electric connection

Pneumatic connection

Commissioning
Illustration of a function diagram
Figure 1 om5510_05_sips2_x0053470en.wmf
2 Mechanic connection of the positioner
Normally the positioner is pre-mounted on the actuator or cylinder. If not, follow the
installation guide lines below.
2.1 Mechanic connection to an actuator
Figure 2 shows the mechanic connection of the positioner to an actuator for a control
valve.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-15 / 30
Step A: Mount clamping assembly (3) with hexagon socket cap screws (17) and lock
washers (16) on the actuator spindle.
Step B: Insert the pick-up bracket (2) into the recesses of the clamping assembly.
Set the necessary length and tighten the screws so that the pick-up bracket
can still be shifted.
Step C: Push the roll (5), spring (13), and guide washer (22) onto the pin (4).
Step D: Insert the pin in the lever (6) and assemble with nut (18), spring washer (14),
and U-washer (12).
Step E: The value of the stroke range specified on the actuator should be set or if
this does not exist as a scaling value, the next greatest scaling value should
be set. The centre of the pin must be in line with the scaling value. The same
value can be set later under parameter 3.YWAY in commissioning to dis-
play the way in [mm] after initialisation.
Step F: Assemble the hexagon socket cap screw (17), spring washer (16), washer
(12), and square nut (19) on the lever.
Step G: Push the pre-mounted lever onto the positioner axis up to the stop and fix
with the hexagon socket cap screw (17).
Step H: Fit the mounting bracket (1) with two hexagon head screws (9), lock washer
(10), and flat washer (11) on the rear of the positioner.
Step I: Selection of the row of holes depends on the width of the actuator yoke. The
roll (5) should engage in the pick-up bracket (2) as close as possible to the
spindle but may not touch the clamping assembly.
Step J: Hold the positioner with the mounting bracket on the actuator so that the pin
(4) is guided within the pick-up bracket (2).
Step K: Tighten the pick-up bracket.
Step L: Position the mounting parts according to the type of actuator.
- Actuator with ledge: hexagon head screw (8), flat washer (11), and lock
washer (10).
- Actuator with plane surface: four hexagon head screws (8), flat washer
(11), and lock washer (10).
- Actuator with columns: two U-bolts (7), four hexagon nuts (21) with
flat washer (11), and lock washer (10).
Step M: Secure the positioner onto the yoke using the previously positioned mount-
ing parts.
Note: Set the height of the positioner so that the horizontal lever position is
reached as close to the stroke centre as possible. The lever scale can be used
as orientation. It must be guaranteed that the horizontal lever position is
passed through within the stroke range.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-16 / 30 Language UK
Mechanic connection of the positioner (linear actuator)
Figure 2 om5510_05_sips2_x0053480en.wmf
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-17 / 30
2.2 Mechanic connection to a pneumatic cylinder
The positioner is connected to a pneumatic cylinder by means of fixing bracket, lever
arm with Allen screw, extension arm, and roller.
The pneumatic piston is connected to a guide rail with an oblique angle via a linkage.
The guide rail moves together with the piston, and the roller/lever connection senses
the position of the piston. By operating both sides of the pneumatic cylinder, the set
point is reached. A spring inserted between the fixing bracket and the lever arm secures
that the roller is pressed down against the guide rail.
2.3 Mechanic connection to a rotary actuator
Figure 3 shows the mechanic connection of the positioner to a rotary actuator.
Step A: Attach the mounting console (9, actuator specific) onto the rear of the po-
sitioner and secure using the hexagon head screws (14) and lock washers
(15).
Step B: Adhere pointer (4.2) onto the mounting console in the centre of the centring
hole.
Step C: Push coupling wheel (2) onto the positioner axis, pull back by about 1 mm
and tighten the hexagon socket head screw (18) with the Allen key provided.
Step D: Place the carrier (3) onto the end of the actuator and secure using Fillister
head screw (16) and washer (17).
Step E: Carefully place the positioner with mounting console onto the actuator such
that the pin of the coupling wheel engages in the driver.
Step F: Align the positioner/mounting console assembly in the centre of the actuator
and screw tight (screws are not included in the delivery, they are part of the
actuator mounting console).
Step G: Follow the start-up sequence as described later. Drive the actuator to the end
position and adhere the scale (4.1) onto the coupling wheel (2) according to
the direction of rotation and rotaryactuator. The scale is self-adhesive.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-18 / 30 Language UK
Mechanic connection of the positioner (rotary actuator)
Figure 3 om5510_05_sips2_x0053490en.wmf
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-19 / 30
3 Electric connection of the positioner
When the positioner is connected in a two-wire system, the positioner draws its power
exclusively from the 4 to 20 mA set point signal. Figure 4 indicates the input circuits
for the positioner.
View of the controls and connections
Figure 4 om5510_05_sips2_x0053500en.wmf
4 Pneumatic connection
Ensure that the air quality is suitable. Grease-free instrumental air with a solid content
<30 m and a pressure dew point 20 K below the lowest ambient temperature must be
supplied.
Warning: For reasons of safety, pneumatic power may only be supplied after
assembly when the positioner is switched to operating level P man-
ual operation with electrical signal applied.
4.1 Selection of P manual mode
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-20 / 30 Language UK
4.1.1 Selection of P manual mode
Before pneumatic power is connected, the positioner must be in P manual mode. The
display must show NOINIT in the bottom line.
4.1.2 Pneumatic connections
Figure 4 shows a view of the positioner controls and connections.
Step A: If required, connect a manometer block for supply air and actuating pressure.
Step B: The silencer in the exhaust output can be removed if necessary.
Step C: Connect actuating pressure Y1 and/or Y2 (Y2
*)
is only used with double-
acting actuators) according to the desired safety position.
Step D: Connect the supply air (1). The pressure should be between 1.4 to 7 bar.
Note: In order for spring-loaded pneumatic actuators to be able to reliably ex-
ploit the maximum possible actuating path, the supply pressure must be
sufficiently greater than the maximum required final pressure of the ac-
tuator.
4.1.3 Safety positionwhen the electric power supply fails
For a single-action actuator is Y1 deaerated. For a double-action actuator is Y1 equal
to the supply air pressure and Y2 is deaerated.
4.1.4 Restrictors
To increase the positioning times for fast actuators when necessary, the air flow can
be reduced with the restrictors Y1 and Y2 (only for double-action valves). Turning the
restrictors in the clockwise direction reduces the air flow until it is shut off. To set the
restrictors it is recommended to first close them and then open them again slowly (see
initialisation process RUN 3).
4.1.5 Purging air switchover
The purging air changeover switch located above the pneumatic terminal block on the
valve manifold can be accessed when the housing is open. When the switch is in po-
sition IN the interior of the housing is purged with very small quantities of clean and
dry instrument air. In position OUT the purging air is led directly out of the instru-
ment.
5 Commissioning
Commissioning (initialisation) is carried out automatically to a large extend. During
initialisation, the micro controller automatically determines the zero value, full-scale
value, direction of action and positioning speed of the actuator. It uses these to deter-
mine the minimum pulse time and dead zone, hereby optimising the control.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-21 / 30
The positioner can also be operated manually by the pushbuttons and the LCD of the
SIPART PS2.
The commissioning of the positioner can be divided into the following steps:

Preparation for initialisation

Start the automatic initialisation procedure

Set additional parameters if required

Select automatic mode

Figure 5 shows the possible operation modes for the positioner and gives an overview
of how to change between them. The levels are P-manual mode, configuration and
initialisation, manual mode, automatic mode, and diagnostic display. From these
modes it is possible to select operation mode, set operation parameters, restore to fac-
tory setting, run an automatic initialisation, etc.
Operation levels
Figure 5 om5510_05_sips2_x0053510en.wmf
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-22 / 30 Language UK
5.1 Preparation for initialisation
Step A: Check and set the gear transmission switch to the correct position. Fig-
ure 4(position 8) indicates the location of the switch. For linear actuators the
gear transmission switch is set according to the stroke range as described in
Table 2 for the parameter 3.YWAY. For part-turn actuators 90 must be
selected.
Step B: Check that the pneumatic supply power (inlet air) is present. The operating
pressure should be at least one bar greater than is necessary for closing/
opening the valve during initialisation.
Step C: Without initialisation the positioner is in P manual mode and NOINIT
flashes in the display. This level can also be reached by using
55.PRSTfunction (see Table 2).
Step D: Check the free running of the mechanics in the whole actuating range by
moving the actuator with the keys and and driving to the respective
end position.
Step E: With linear actuators drive the actuator to horizontal lever position. The
display must indicate 48% to 52%. If necessary, correct the value by ad-
justing the sliding clutch. After the check is completed, the actuator must be
approximately half way along its stroke. This is due to establishment of the
action direction during automatic initialisation.
5.2 Automatic initialisation
Figure 6 shows the configuration modeincluding the operation in this mode and Ta-
ble 2 shows the parameter/configuration list. Figure 7 shows the initialisation process
of the positioner. The initialisation process is stored in the microprocessor. This means
that an additional initialisation only is necessary if any parts of the unit have been
changed.
Note: The numerical values used in Figure 5, Figure 6, and Figure 7 are examples.
Step A: Call the configuration mode by pressing the hand symbol key for longer than
5 seconds.
Step B: Set the actuator type, linear or part-turn, in the menuitem line 1.YFCT.
Step C: Switch to the second parameter by pressing the hand symbol key briefly.
Step D: Set the rated angle of rotation for feedback in the menu item line 2.YAGL.
It is vital that this value corresponds to the setting of the gear transmission
ratio selector (Figure 4, position 8), 33 or 90.
Step E: Switch to the next parameter by pressing the hand symbol key briefly.
Step F: This parameter (3.YWAY) is only set for linear actuators and if the total
stroke in mm should be displayed at the end of the initialisation phase. To
do this, select the same value in the display to which the carrier pin to the
scale on the lever is set to.
Step G: Switch to the following parameter by pressing the hand symbol key briefly.
Step H: Start the initialisation (4.INITA) by pressing the key for longer than
5 seconds.
Step I: During the initialisation phase RUN1 to RUN5 appear one after another
in the bottom of the display. Please note that the initialisation process may
last up to 15 minutes depending on the actuator.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-23 / 30
Note: The ongoing initialisation can be aborted at any time by pressing the hand
symbol key. The previous settings are retained. All the parameters are reset
to the factory setting only after performing a preset 55.PRST.
Step J: If problems occur, carry out the measures as described in the table Possible
messages shown in Figure 7.
Step K: The initialisation is completed when FINSH appears in the bottom of the
display.
Step L: When pressing the hand symbol key briefly the menu item line 4.INITA
is displayed.
Step M: To exit the configuration operating mode, press the hand symbol key for
longer than 5 seconds. The software version is displayed after about 5 sec-
onds. The instrument is in manual operationafter releasing the key.
Step N: The positioner can be changed to automatic mode by pressing the key
once as indicated in Figure 5.
Step O: The automatic mode is the normal mode. In this mode the positioner com-
pares the set point current with the current position and moves the actuator
until the control deviation reaches the dead zone.
Operation in the configuration mode
Figure 6 om5510_05_sips2_x0053520en.wmf
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-24 / 30 Language UK
Initialisation process
P 32.4
RUN 1
P 32.4
ERROR
Display Meaning Measures
Actuator does
not move
Possible messages
Acknowled ge message
using t he hand symbol key
Set the next highest travel
value on t he lever
Restart initi alisat ion
Additionally possible with rotary
act uators:
Adjust using up and down keys
up to displa y:
Continue u sing hand symbol key
Down tolerance
band violated
Acknowled ge message
using t he hand symbol key
Check restr ictor (6) and open
if necessar y
Drive act uat or to working range
using t he up and down keys
Restart initi alisat ion
Change gea ring (7)
Continue using up key
P 92.8
90_95
SEt
MIDDL
P 98.3
UP >
P 88.4
d u IU
Or adjust sliding clutch up
to display
Then only
Continue using the down key
P 6.4
d 0 IU
Up tol erance band
vi olated
P 19.8
U-d <
Once the slipping
cl utch has bee n
adj usted
Linear actuator: set pick-up
lever into ho rizontal position
using t he up and down keys
Continue using hand symbol key
Acknowledge message
using t he ha nd symbol key
Set the next lowest travel
value on t he lever
Restart initi alisat ion
Adjust posit ioning time using
restrictor(s)
Continue using the
up or down key
U 1.3
NOZZL
d 1.8
NOZZL
Strt
4 INITA
Up/down span
vi olated
Actuator does
not move.
Positioning
time is possibl e
to adjust
Automatic initi al start-up (starting with factory setting)
Step Meaning
turn
1 YFCT
90
O
2 YAGL
WAY
1 YFCT
33
O
2 YAGL
Strt
3 YWAY
Linear
act uator
Part -t urn
act uator
Press the up key for > 5 sec.
Remaining st eps are carried out aut omatically
2.)
1.)
Direction of action is determined
P 32.4
RUN 1
3.)
P 92.4
RUN 2
4.)
P 82.4
RUN 3
5.)
P 32.4
RUN 4
6.)
P 52.4
RUN 5
7.)
32.4
FINSH
8.)
Checking of t ravel and adjustment of
zero andst roke (from stop to st op)
Determina tion and display of positioning time
down (dxx. x), up (uxx.x). St op with the down key
Determina tion of minimumincre ment length
Optimisati on of transient respon se
Init ialisation terminated successfully
(travel in mm f or linear actuat ors)
(angle of r ot ation for part-turn act uators)
Continueu sing hand symbol ke y
Pressing t he up key init iates leakage measurement
Figure 7 om5510_05_sips2_x0053530en.wmf
5.3 Parameters
Table 2 shows the parameter list for the positioner. The parameter name is written in
plain text in the menu line column. The function of the parameter is described briefly
in the Function column. In addition, the possible parameter values, the physical unit
and the factory setting of the parameters are shown.
After the initialisation process, the positioner can be configured to meet the require-
ments of a specified task. The factory settings correspond to the requirements for a
typical application. This means that normally only a few parameters will need to be
changed.
The positioner can be installed and configured to fit linear and part-turn actuators with
reverse action. E.g. linear actuators with the set point in the falling direction or part-
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-25 / 30
turn actuators for counter clockwise operation direction. In this case the parameters
7.SDIR and 38.YDIR should be set to FALL.
Parameter list
Menu line Function Parameter values Unit
Factory set-
ting
Customer
setting
1.YFCT Type of actuator
turn (part-turn actua-
tor)
WAY (linear actuator)
LWAY (linear actuator
without sine correc-
tion)
ncSt (part-turn actuator
with NCS)
-ncSt (part-turn actua-
tor with NCS, inverted)
WAY
2.YAGL
1)
Rated angle of rotation for feedback
(must correspond to gear ratio)
90
33
Degrees 33
3.YWAY
2)
Stroke range (optional setting)
When used, the value must correspond
with the set of the leverage ratio on the ac-
tuator
Driver pin must be set to the value of the
actuator travel or, if this value is not
scaled, to the next lager scale value
OFF
mm OFF
5 , 10 , 15 , 20
(short lever 33)
25 , 30 , 35
(short lever 90)
40 , 50 , 60 , 70 ,
90 , 110 , 130
(long lever 90)
4.INITA Initialisation (automatically) noini / no / ###.# / Strt no
5.INITM Initialisation (manually) noini / ###.# / Strt no
6.SCUR Current range of set point
0 to 20 mA 0 MA
4 MA
4 MA
4 to 20 mA
7.SDIR Set point direction
rising riSE
FALL
riSE
falling
8.SPRA Set point for start of split range 0.0 to 100.0 % 0.0
9.SPRE Set point for end of split range 0.0 to 100.0 % 0.0
10.TSUP Set point ramp up
Auto
0 to 400
s 0
11.TSDO Set point ramp down 0 to 400 s 0
12.SFCT
Set point function
Linear
Equal-percentage 1:25, 1:33, 1:50
Inverse equal-percentage 1:25, 1:33, 1:50
Freely adjustable
Lin
125 , 133 , 150
n125 , n133 , n150
FrEE
Lin
13.SL0
3)
14.SL1
to
32.SL19
33.SL20
Set point turning point at 0%
5%
to
95%
100%
0.0 to 100.0 %
0.0
5.0
to
95.0
100.0

34.DEBA Dead zone of controller
Auto
0.1 to 10.0
% Auto
35.YA Start of manipulated variable limiting 0.0 to 100.0 % 0.0
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-26 / 30 Language UK
Parameter list
36.YE End of manipulated variable limiting 0.0 to 100.0 % 100.0
37.YNRM
Standardisation of
manipulated variable
To mech. travel
To flow
MPOS
FLOW
MPOS
38.YDIR
Direction of manipulated
variable for display
Rising
Falling
riSE
FALL
riSE
39.YCLS
Tight closing with
manipulated variable
Without
Top only
Bottom only
Top and bottom
no
uP
do
uPdo
no
Table 1
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-27 / 30
Parameter list continued
Menu line Function Parameter values Unit
Factory set-
ting
Customer
setting
40.YCDO Value for tight closing, bottom 0.0 to 100.0 % 0.5
41.YCUP Value for tight closing, top 0.0 to 100.0 % 99.5
42.BIN1
4)
Function of BI 1:
None
Only message (NO/NC contact)
Block configuring (NO contact)
Block configuring and manual (NO con-
tact)
Drive valve to pos. up (NO/NC contact)
Drive valve to pos. down (NO/NC contact)
Block movement (NO/NC contact)
OFF
on / -on
bLoc1
bLoc2
uP / -uP
doWn / -doWn
StoP / - StoP
OFF

43.BIN2
4)
Function of BI 2:
None
Only message (NO/NC contact)
Drive valve to pos. up (NO/NC contact)
Drive valve to pos. down (NO/NC contact)
Block movement (NO/NC contact)
OFF
on / -on
uP / -uP
doWn / -doWn
StoP / -StoP
OFF
44.AFCT
5)
Alarm function
Without
A1=min. A2=max.
A1=min. A2=min.
A1=max. A2=max.
oFF
N , NA
N , N
NA , NA
OFF
45.A1 Response threshold of alarm 1 0.0 to 100.0 % 10.0
46.A2 Response threshold of alarm 2 0.0 to 100.0 % 90.0
47.FCT
6

)
Function of alarm output
On fault
Fault + not automatic
Fault + not automatic + BI
(+ means logical OR operation)

nA
nAb

48.TIM
Monitoring time for fault message
control deviation
Auto
0 to 100
s Auto
49.LIM
Response threshold for fault message
control deviation
Auto
0.0 to 100.0
% Auto
50.STR
K
Limit for stroke integral
OFF
1 to 1.00E9
OFF
51.DCH
G
Limit for direction change
OFF
1 to 1.00E9
OFF
52.ZER
O
Limit for end stop monitoring, bottom
OFF
0.0 to 100.0
% OFF
53.OPE
N
Limit for end stop monitoring, top
OFF
0.0 to 100.0
% OFF
54.DE-
BA
Limit for dead zone monitoring
OFF
0.0 to 100.0
% OFF
55.PRST
Preset (factory setting)
no nothing activated
Strt start of factory setting after pressing
key for 5 sec.
oCAY display following successful fac-
tory setting
no
Strt
oCAY

POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-28 / 30 Language UK
Parameter list continued
CAUTION: preset results in NO INIT
1)
If turn is selected it is not possible to set 33.
2)
Parameter does not appear if 1.YFCT = turn has been selected.
3)
Turning points only appear with selection 12.SFCT = FrEE.
4)
Alternatively no if initialisation has not yet been carried out.
5)
NC contact means; action with opened switch or low level. NO contact means; action with closed switch or high level.
6)
Normal means: high level without fault. Inverted means: low level without fault.
Table 2
6 Diagnosis
In the diagnostic mode the current operating data (such as number of strokes, number
of changes in direction, number of fault messages, etc.) can be displayed.From the
automatic or manual modes the diagnostic mode can be reached by simultaneously
pressing all three keys for at least 2 seconds.
Table 3 shows an overview of the displayable values. The diagnostic display has a
similar structure as the parameter menu displays. The respective next diagnostic value
can be selected with the hand symbol key. Certain values can be set to zero by pressing
the key for at least 5 seconds. These are menu item line 1, 2, 3, and 4. Some
diagnostic values may be greater than 99999. In this case the display switches to ex-
ponential display.
Diagnostic list
No.: Abbreviation Meaning Displayable
value
Unit
1 STRKS Number of strokes 0 to 4.29E9 -
2 CHDIR Changes of direction 0 to 4.29E9 -
3 CNT Fault counter 0 to 4.29E9 -
4 A1CNT Alarm counter 1 0 to 4.29E9 -
5 A2CNT Alarm counter 2 0 to 4.29E9
6 HOURS Operating hours 0 to 4.29E9 Hours
7 WAY Determined actuating path 0 to 130 mm or
8 TUP Travel time up 0 to 1000 s
9 TDOWN Travel time down 0 to 1000 s
10 LEAK Leakage 0.0 to 100.0 %
11 P0 Potentiometer value below stop (0%) 0.0 to 100.0 %
12 P100 Potentiometer value bottom stop (100%) 0.0 to 100.0 %
13 IMPUP Impulse length up 2 to 100 ms
14 IMPDN Impulse length down 2 to 100 ms
15 DBOP Dead zone up 0.1 to 100.0 %
16 DBDN Dead zone down 0.1 to 100.0 %
17 SSUP Short step zone up 0.1 to 100.0 %
18 SSDN Short step zone down 0.1 to 100.0 %
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
Language UK 13-29 / 30
Diagnostic list
19 TEMP Current temperature -45 to 85 C
20 TMIN Minimum temperature -45 to 85 C
21 TMAX Maximum temperature -45 to 85 C
22 T1 Number of operating hours in Temperature range 1 0 to 4.29E9 Hours
23 T2 Number of operating hours in Temperature range 2 0 to 4.29E9 Hours
24 T3 Number of operating hours in Temperature range 3 0 to 4.29E9 Hours
25 T4 Number of operating hours in Temperature range 4 0 to 4.29E9 Hours
26 T5 Number of operating hours in Temperature range 5 0 to 4.29E9 Hours
27 T6 Number of operating hours in Temperature range 6 0 to 4.29E9 Hours
28 T7 Number of operating hours in Temperature range 7 0 to 4.29E9 Hours
29 T8 Number of operating hours in Temperature range 8 0 to 4.29E9 Hours
30 T9 Number of operating hours in Temperature range 9 0 to 4.29E9 Hours
31 VENT1 Number of cycles pre-control valve 1 0 to 4.29E9 -
32 VENT2 Number of cycles pre-control valve 2 0 to 4.29E9 -
33 STORE
Store current values as last maintenance
Press the up key for at least 5 seconds (store)
- -
Table 3
7 Service and maintenance
The positioner is largely maintenance-free. The positioner is fitted with filters in the
pneumatic connection as protection against coarse particles of dirt. If the pneumatic
energy supply contains particles of dirt, the filters may be clog and impair the function
of the positioner. In this case the filters can be cleaned as follows:
Step A: Switch off the pneumatic power supply and remove the pipes.
Step B: Unscrew the cover.
Step C: Remove the three screws from the pneumatic connector strip.
Step D: Remove the filters and O-rings behind the connector strip.
Step E: Clean the filters (e.g. with compressed air).
Step F: After cleaning first insert the filters in the recesses in the housing and then
place the O-rings on the filters.
Step G: Align the pneumatic connector strip on the two lugs and screw tight with
the three self-tapping screws.
Note: Make sure that the same thread is used. To do this, turn the screws anti-
clockwise until they snap into the thread audibly. Only then should the
screws be tightened.
POSITIONER, SIPART PS2 6DR5000 OM5510_05#A.2
13-30 / 30 Language UK
Table of contents
Chemical dosing pump
Description Document ID Page
.
Chemical dosing pump............................................... OM5540_07.............. 14-2
Relief valve.............................................................. OM6000_01.............. 14-14
TABLE OF CONTENTS
Language UK 14-1 / 16
Chemical dosing pump
1 General
The chemical dosing pump is a microprocessor controlled solenoid metering pump.
The pump offers highly accurate reproducible metering in the dosing of liquid chem-
icals in pressurised pipe systems, and into open and closed containers. The main com-
ponents of the chemical dosing pump are the operating panel, power end, and liquid
end Figure 1 illustrates the chemical dosing pump.
The working principle of the pump is that chemical feed occurs as a result of pulsed
deflections of the dosing diaphragm within the liquid end, which causes pressure dif-
ferentiation between the suction side, liquid end cavity, and discharge side. The pres-
sure differentiation causes the suction and discharge self-acting valves to open and
close, resulting in chemical feed. The dosing diaphragm is driven by an electromagnet,
which is stimulated and controlled by a microprocessor.
Regulation of the required dose is variable via the stroke length in the range of10-100
% in steps of 10% or can be set at 1 of the 4 settings via the stroke frequency. This
gives an adjustment ratio of 1:40. Optimum dosing reproducibility is achieved by set-
ting the stroke length between 30% and 100%. For external actuation a retrofit kit is
needed in addition.
Illustration of the chemical dosing pump
Figure 1 om5540_07_chem_0x0200520en.wmf
CHEMICAL DOSING PUMP OM5540_07#A.2
14-2 / 16 Language UK
2 Safety
The following guidelines describe correct use of the equipment and how to avoid po-
tentially dangerous situations and must always be observed during installation, com-
missioning, operation, maintenance, and repair.

The pump may be used only for metering liquid media!

All other uses or modifications are prohibited!

The pump is not suitable for metering gaseous media or solids!

The pump must be operated by appropriately trained and authorised personnel!

The personnel must be familiar with metering pumps and their operation!

The pump may start to operate as soon as it connected to the mains power supply!
Ensure that no hazardous metering chemical can leak out! If you have not done so,
set the multifunction switch to STOP or disconnect the pump from the mains im-
mediately.

The pump cannot be switched off! In the case of an electrical failure, disconnect
the mains cable from the power supply.

Disconnect the power cable from the mains before working on the pump.

Risk of electric shock - This pump is supplied with a grounding conductor and
grounding-type attachment plug. To reduce the risk of electric shock, be certain
that it is connected only to a properly grounding-type receptacle.

Always depressurise liquid end before working on the pump.

Always empty and rinse the liquid end before working on the pump if used with
hazardous or unknown feed chemicals.

Wear safety equipment appropriate to the metering chemical when working on the
liquid end.

Never let the pump work against a significantly increased operating pressure or a
closed stop tap on the discharge-side. This can cause lines to burst.

Avoid overfeed due to positive pressure difference between intake and discharge
sides. E.g. use a ball check valve with at least 1.5 bar opening pressure with an
atmospheric pressure outlet.

Assembly and installation of this metering pump with non original parts, which
have not been checked and recommended by supplier is not allowed and can lead
to harm to persons or property for which no liability can be accepted.

Note all national directives which apply to the installation.

CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-3 / 16
3 Installation
The chemical dosing pump is normally pre-mounted on a chemical tank. However, in
case that the pump must be mounted elsewhere or replaced please observe the following
general installation notes:

The chemical dosing pump must be located in an environment with ambient tem-
perature between -10C to +45C and a maximum permissible relative humidity
of 92% non-condensing.

The pump must be mounted with the pump foot resting on a firm horizontal base.
Ensure that it is fastened into place firmly, and will not vibrate in operation.

The maximum permissible priming and operating pressures must not be exceeded.
For this type of pump the maximum priming lift is 2 mm WC and the maximum
operating pressure is 16 barg. In case that the operating pressure is exceeded, e.g.
due to the position of the chemical feed into the feed water system, the discharge
side must be provided with a relief valve. The surplus chemicals should be led
back to the chemical tank.

Suction and discharge valves must be installed in a vertical position.

The tubing should be attached in such a way that it allows lateral detachment of
the pump and liquid end, if necessary. The tubing must be free from stress and
bends when fitted. Only original hoses with the correct dimensions should be used.

The suction tubing should be as short as possible and rising in order to prevent air
bubbles forming.

The foot valve should be installed so that it hangs just above the bottom of the
chemical tank. For chemicals with impurities or sedimentation at the bottom, the
foot valve should be positioned well above this layer.

The check valve, which connects the discharge line to the feed water system, must
be tightened properly.
3.1 Assembling of the tubing to plastic valves
3.1.1 Assembling of the tubing to plastic valves
When assembling the suction and discharge tubing to the plastic valves of the liquid
end carry out the following work procedures (see figure 2).
Step A: Cut the hose ends straight across.
Step B: Push the union nut and clamping ring onto the hose.
Step C: Push the hose end over the grommet to the stop (widen if necessary).
Step D: Ensure that the O-ring is sitting correctly onto the intake connector.
Step E: Clamp the connector hose by tightening the union nut while pressing in the
hose.
Step F: Retighten the hose connector by pulling the hose connected to the liquid end
briefly and then retighten the union nut.
CHEMICAL DOSING PUMP OM5540_07#A.2
14-4 / 16 Language UK
Assembling of the tubing to plastic valves
(Section)
Hose
Clamping
ring
Grommet
Intake
connector
O-Ring
Union nut
Figure 2 om5540_07_chemicx0053980en.wmf
3.2 Electrical installation
The pump is connected to the mains power supply by using the mains lead. If the pump
is connected to the mains in parallel with inductive power consumers (e.g. solenoid
valves, motors) it must be electrically isolated. This prevents damage caused by in-
duction and voltage surges when switching off.
4 Commissioning
Step A: Check that the connections for the pump are completed properly.
Step B: Open the bleed valve by rotating the knob anticlockwise (see Figure 3)
Step C: Switch on the pump and allow it to run at maximum stroke length and rate
until the liquid end is full and free from air bubbles (the feed chemical is
visible at the bleed valve). The stroke length should only be set while the
pump is running (see Figure 3).
Note: The pump should prime at 100% stroke length as the suction lift is de-
pendent upon the lift volume when the liquid end is empty. If the pump is
required to prime at less than 100% stroke length, and fails to do so, then
select a correspondingly smaller suction lift.
Step D: Close the bleed valve (turn clockwise).
Step E: Switch off the pump.
Step F: The pump is ready to operate. Retighten screws in the liquid end after 24
hours operation time. Tightening torque for liquid end screws: 4.5 to 5 Nm.
CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-5 / 16
Illustration of liquid end
Liquid end
Suction
valve
Discharge
valve
Bleed
valve
Figure 3 om5540_07_chem_px0053970en.wmf
4.1 Determining the feed capacity
When the necessary chemical dosing feed is known, e.g. by means of feed and boiler
water analysis, the feed capacity of the pump can be set. Figure 4 shows the feed rate
setting diagram for the pump. The measurements for determining the feed rate from
the diagram were carried out using water as medium. In order to find the feed capacity
the correction factor must be found and subsequently the stroke rate and stroke length
should be set. For determination of the feed capacity carry out the following proce-
dures:
Step A: Mark the operating pressure for the chemical dosing pump in the lower di-
agram. The operating pressure is equal to the pressure in the feed water
system at the point of dosing.
Step B: Trace a line from this value vertically up to the curve and then horizontally
left. Read off the correction factor.
Step C: Divide the required feed rate by the determined correction. Mark this value
(l/h) on the "l/h" axis in the upper diagram.
Step D: Trace a horizontally line from this value to the left. Trace a line from the
intersection with the straight line for the adjustable stroke frequencies ver-
tically downwards the "stroke length" axis.
Step E: Set the pump to one of the stroke frequencies determined in this way, and
the corresponding stroke length.
CHEMICAL DOSING PUMP OM5540_07#A.2
14-6 / 16 Language UK
Feed rate setting diagram
1,6
1,4
1,2
1
0,8
0,6
0,4
0,2
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
0
I
/
h
180 strokes/min
135 strokes/min
90 strokes/min
45 strokes/min
Stroke length
CNPa 1601 at medium back pressure
2
1,5
1
0,5
0
1 2 3 4 8 11 13 16
Back pressure`
Correction factor
Figure 4 om5540_07_chem_gx0053960en.wmf
5 Operation
The operation panel of the chemical dosing pump is equipped with operation knobs/
switches, connection terminals, and indicators, which support the operation and setting
of the pump. Figure 5illustrates the operation panel of the chemical dosing pump.
CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-7 / 16
The pump can be operated through manual control or external control. If the pump is
intended only to operate in manual mode it will not be provided with the optional socket
connection for "external control. When the pump is intended to operate via "external
control" and/or "float switch", a external connection retrofit kit and/or float switch
retrofit kit must be provided.
The "Float switch" option provides information on the liquid level in the feed chemical
tank, which is transmitted to the pump. This option requires the installation of a one-
stage float switch and connection to the "float switch" socket.
The following instruction for pump operation is described as a complete instruction.
If the chemical dosing pump includes parts or features, which are not provided for the
actual dosing unit, the specified instructions should be disregarded.
Illustration of the operating panel for the chemical dosing pump
6
7
8
5
4
3
2
1
1. Stroke lenght adjustment knob
2. Error / operating indicator (error - red / operation -
green)
3. Multifunction switch (stroke rates (in % of
180 strokes / min), stop operating mode
external (Retrofit kit))
4. Power cable
5. External actuation socket (actuation via contact
signal in external operating mode; Retrofit kit)
7. Suction valve
8. Disharge valve

The leakage bore is between the suction valve and
the drive housing.
Figure 5 om5540_07_chemx0053950en.wmf
5.1 Basic information for the pump
5.1.1 Stroke length adjustment knob
The stroke length is continuously adjustable between 0% and 100% via the stroke
length adjustment knob. Reproducibility is only technically practicable in the adjust-
ment range 30% to 100%.
CHEMICAL DOSING PUMP OM5540_07#A.2
14-8 / 16 Language UK
5.1.2 Multifunction switch
The multifunction switch is used to select the operating mode and to set the stroking
rate. The following operating modes are selected using the multifunction switch:

Stop.

External.

Manual (to set stroking rate in 10% steps).

Stop
- The "Stop" function allows the pump to be deactivated without disconnecting from
the power supply.
External
- The "External" operating mode allows adjustment of individual strokes via the
external operating mode terminal by means of contact or semi-conductor devices.
- The "Auxiliary frequency" operating mode enables activation of optionally se-
lectable and programmable stroking rate, controlled via the external operating
mode terminal. This stroking rate overrides "Manual" and "External" operating
modes. In the standard version the "Auxiliary frequency" function is programmed
to 100% stroking rate.
- The "Pause" function can be used to operate a remote pump stop function via the
external operating terminal.
Manual
- In the "Manual" operating mode the stroking rate is manually adjustable in 10%
steps via the multifunction switch.
5.1.3 Error/operating Indicator
The operating and error status are shown via the error/operating indicator on the op-
erating panel:

Green indicator: During operation the indicator is green.

Red indicator: If an error occurs the indicator is red.

CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-9 / 16
6 Maintenance
To ensure a safe and reliable function of the chemical dosing pump maintenance work
must be performed with regular intervals. The normal maintenance interval is three
months. This is based on approximately 30% operation time. But in case of heavier
use (e.g. continuous operation) the intervals should be shortened. Carry out the fol-
lowing maintenance work:

Check for the correct feed rate by running the pump for a short period.

Check that the discharge tubing is connected firmly the liquid end.

Check that the discharge and suction valves are firmly fixed.

Check that the liquid end is generally watertight, in particular leakage opening
between suction value and drive housing.

Check the diaphragm for damage.

Check that the liquid end screws are fastened tightly. The screw fastening torque
should be 4.5 to 5.0 Nm.

Check that the bleed valve is firmly fixed in place (see Figure 6).

Check that the bleed function is working correctly (see Figure6).

Check the electrical connections for wear.

7 Repair
Repair work should only be carried out by qualified personnel. Suitable precautions
must always be taken when using hazardous chemicals. Furthermore, is must be en-
sured that the pump and suction/discharge lines are de-pressurised. Figure 6 illustrates
the discharge valve, suction valve, and exchanging of the diaphragm.
Illustration of discharge valve, suction valve, and exchanging of diaphragm
Discharge valve Suction valve
1 Screws
2 Liquid end
3 Diaphragm
4 Top plate
5 Safety diaphragm
6 Pump housing
Figure 6 om5540_07_chemicx0053990en.wmf
7.1 Cleaning valves
7.1.1 Cleaning the discharge valve
Step A: Loosen the discharge line from the valve.
CHEMICAL DOSING PUMP OM5540_07#A.2
14-10 / 16 Language UK
Step B: Unscrew the discharge valve from the liquid end and rinse thoroughly.
Step C: Remove the O-ring from the liquid end with a small screwdriver.
Step D: Insert an Allen key or similar into the smaller hole of the pressure connector
and push out the valve inserts.
Step E: Remove the valve seats with a small screwdriver and allow the valve balls
to drop out.
Step F: Clean all parts.
Step G: Drop the valve balls into the valve seats and push them on the valve inserts.
Step H: Press the valve seats into the pressure connector with their smaller hole in
the direction of the flow (see the direction of the arrows on the fluting of the
pressure connector).
Step I: Insert the O-ring into the liquid end.
Step J: Screw the valve in as far as it will go.
Step K: Secure the discharge line onto the valve.
Step L: Reset the pump after replacing a valve.
7.1.2 Cleaning the suction valve
Dismantling, cleaning, and reassembling of the suction valve is practically the same
as for the discharge valve. Take care, however, that:
- Both valve inserts are actually identical.
- An additional spacer is found under the valve inserts.
- In the liquid end a shaped seal is used instead of an O-ring.
- The flow direction of the suction connection is reversed as for the pressure con-
nector.
7.1.3 Change diaphragm
Step A: When the pump is running set the stroke length to 0% (the drive axis is then
set). Switch off the pump.
Step B: Unscrew the connectors from the discharge and suction side.
Step C: Pull out the fine bleed (knob) and lift off the cover from the liquid end using
a screwdriver.
Step D: Empty the liquid end (turn the unit upside down and let the feed chemical
run out, rinse with a suitable material).
Step E: Remove the screws.
Step F: Loosen (only loosen) the liquid end and the top plate from the pump housing.
Step G: Hold the housing in one hand and with the other, clamp the diaphragm be-
tween the liquid end and the top plate. Release the diaphragm from the drive
spindle with a light anticlockwise turn of the liquid end and top plate.
Step H: Unscrew the diaphragm completely from the drive spindle.
Step I: Remove the top plate from the housing. Please note the position.
Step J: Check the condition of the safety diaphragm and replace if necessary.
Step K: Push the safety diaphragm only as far onto the drive axis until it just lies flat
on the pump housing.
Step L: Screw the new diaphragm carefully up to the stop on the drive axis - this
must be exact to ensure correct metering.
Step M: Screw the diaphragm tight once more.
CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-11 / 16
Step N: Position the top plate on the pump housing. The top plate must be positioned
correctly. Do not distort the top plate on the pump housing, otherwise the
safety diaphragm will not fit.
Step O: Lay the diaphragm onto the top plate.
Step P: Hold the top plate and screw the diaphragm in a clockwise direction until it
is firmly in position (the resistance of the return spring can be felt). Do not
over-tighten the diaphragm.
Note: The top plate must remain in position to prevent the safety diaphragm from
distorting.
Step Q: Place the liquid end with the screws on the diaphragm and the top plate. The
priming connector must point downwards once the pump is fully assembled.
Step R: Screw on the screws lightly and tighten. The torque should be 4.5 to 5.0 Nm.
Step S: Ensure that the liquid end cover engages in the liquid end and push the bleed
vent (knob) into the liquid end.
Step T: Check the screw torque after 24 hours operation time.
CHEMICAL DOSING PUMP OM5540_07#A.2
14-12 / 16 Language UK
8 Trouble shooting
The trouble shooting list is based on a proper set-up of the chemical dosing pump
during commissioning and/or service. The list can be seen in Table 1.
Please note that the trouble shooting list is general for chemical dosing pumps and has
not been made for any particular plant, but is based on several years of experience.
Therefore, the cause of the specific problem may not be mentioned and vice versa. You
are always welcome, however, to contact our service department for advice or service
assistance.
Fault finding chart
Fault Possible cause Remedy
Pump does not prime despite full
stroke and venting.
Crystalline deposits on the ball seat because valves
have dried out.
Remove suction sleeve from chemical
supply and rinse out liquid end through-
ly.
If still unsuccessful, dismantle valves
and clean.
Fluid is leaking from the head
washer.
The liquid end is leaking at the pump diaphragm. Screw in the liquid end anti-clockwise
(torque: 4.5 to 5.0Nm). If unsuccessful,
replace the diaphragm.
Error/operating indicator not lit. No or incorrect mains voltage.
Fuse defective.
Use the recommended mains voltage as
given in the voltage specification on the
name plate.
Contact Aalborg Industries.
Error/operating indicator lit red. Liquid level in the supply tank has reached low
liquid level. (if float switch retrofit kit provided).
Electronic failure.
Fill the chemical storage tank.
The pump needs repair. Contact Aalborg
Industries.
Table 1
9 Decommissioning
When dismantling a pump, clean thoroughly, paying particular attention to the liquid
end in order to remove all traces of chemicals and dirt. When disposing of a pump it
must be broken down into separate material types. All parts must be sent for recycling
or for correct disposal according to currently legal waste disposal requirements.
CHEMICAL DOSING PUMP OM5540_07#A.2
Language UK 14-13 / 16
Relief valve
1 Description
The purpose of the relief valve is to protect the delivery line from impermissible over-
pressure caused by the chemical dosing pump. It features a pressure relief mechanism
for both the pressure retaining function as well as for the pressure relief function. The
valve functions are affected by means of a spring-loaded diaphragm. Figure 1 illustrates
the multi-function relief valve. The relief valve has an overflow opening pressure of
16 bar. But depending on the pump type, the pressure may be up to 50% higher until
the valve is completely opened.
Illustration of the relief valve
Black knob Red knob
Pressure connection
of the pump
Delivery line
connection
By-pass
connection
Figure 1 om6000_01_reliefx0056540en.wmf
RELIEF VALVE OM6000_01#A.2
14-14 / 16 Language UK
1.1 Functional description

Producing a defined back pressure for chemical dosing with respect to free outlet.
The function can be cancelled by turning the black knob in clockwise direction.

Prevents lift-through from the feed water system in case of vacuum at the dosing
point. The function can be cancelled by turning the black knob in clockwise di-
rection.

Intake aid to prevent pressure when starting up the pump. It is not necessary to
release the delivery line. The function can be achieved by turning the red knob.

Depressurising the delivery line when the feed water system is at a standstill (e.g.
repair). The function can be achieved by turning both the red knob and black knob.

Overflow valve to protect the system from impermissible overpressure caused by

the chemical dosing pump. The return flow is via a by-pass line. This function
takes place automatically.
Note: The relief valve must not be used as a shut-off element and the by-pass line
must always be connected.
1.2 Mounting and installation
The relief valve is screwed directly onto the pressure connection of the pump and can
be turned or aligned through 360. The delivery line or hose is secured on the valve
outlet end by means of a connection set or GF screw fitting. An EPDM O-ring is fitted
at the factory in the O-ring groove at the outlet. For applications in which EPDM is
not suitable, it is advisable to fit a Viton B O-ring. This O-ring (brown) is supplied
together with the valve.
The by-pass line is routed into the chemical tank and secured by means of a hose
grommet and union nut. The by-pass line must always be connected since a minimum
overflow into the by-pass line can occur during operation of the valve close to the
pressure relief function.
Attention: A non-return valve must be installed at the dosing point since the
entire contents of the system can flow back via the by-pass when the
valve is operated.
1.3 Operation
Operation and setting the intake aid
The route to the by-pass line is cleared by means of the red knob by turning it in the
direction indicated by the arrow (clockwise). The liquid flows back into the chemical
tank. In this case, the delivery line is partly depressurised and the liquid can flow out
of the by-pass. The chemical dosing pump must now be set to "intake" until the liquid
can be seen in the by-pass line. The pump is now primed and can be placed into op-
eration. After being released, the red rotary knob reverts of its own accord back to its
initial position.
RELIEF VALVE OM6000_01#A.2
Language UK 14-15 / 16
Depressurising the delivery line
The passage from the delivery line to the by-pass can be cleared by means of the red
knob and the black knob by turning them in the direction indicated by the arrows
(clockwise). The pressure drops in the line to approximately 1.5 bar if only the red
knob is turned. Both knobs must remain unscrewed until no more liquid flows out of
the by-pass line or no more liquid flows back into the chemical tank. The delivery line
is now depressurised. Once released, both rotary knobs revert of their own accord back
to their initial position.
RELIEF VALVE OM6000_01#A.2
14-16 / 16 Language UK
Table of contents
Oil detection equipment
Description Document ID Page
.
Oil detection equipment.............................................. OM9410_01.............. 15-2
TABLE OF CONTENTS
Language UK 15-1 / 11
Oil detection equipment
1 General
This chapter contains installation, operation, and maintenance instructions for the ul-
trasonic interface detection system, Mobrey type 402 SD, using control unit type
MCU200.
Each Mobrey ultrasonic control system requires a sensor to suit the specific application,
plus a control unit. These instructions cover the control units in the MCU200 series.
2 Sensor installation
2.1 General description
The ultrasonic sensor contains two piezoelectric crystals. A high frequency signal (3.7
MHz) generated by the control unit is transmitted to one piezoelectric crystal by coaxial
cable. This crystal converts the electrical signal into an ultrasonic oscillation.The sen-
sor design allows the ultrasonic oscillation to pass from the transmitter crystal to the
receiver piezoelectric crystal. The sensors of type 402 are gap type sensors, where
the two piezoelectric crystals are separated by a gap. When the gap is in liquid the
signal reaches the receiver, because of the low ultrasonic attenuation of the liquid.
When the gap is filled with air, no ultrasonic signal can pass from transmitter to re-
ceiver. See Figure 1.
Working principle of the oil detection equipment
Figure 1 om9410_01_mobreyx0063070en.wmf
OIL DETECTION EQUIPMENT OM9410_01#A.2
15-2 / 11 Language UK
When the gap is filled with liquid, the piezoelectric receiver crystal converts the ul-
trasonic wave into an electrical signal, which is transmitted back to the control unit
using a second coaxial cable. Usually the two coaxial cables to the sensor are in one
overall sheath. The control unit circuitry is a feedback amplifier, which oscillates when
the sensor is wet, and is quiescent for the sensor dry. The oscillating or non-oscil-
lating sensor states dictate the output relay states of the MCU200.
For interface detection the sensor oscillates in a clear liquid, and is non-oscillating
at the interface.
2.2 Switching levels and orientation
The gap sensors should normally be mounted with the gap vertical, to avoid build up
of solids on the sensor faces on either side of the gap. In this condition the switching
level will be half way up the face: if the sensor is mounted from the side of the tank
this is normally on the centreline of the cylindrical body.
Occasionally such sensors are mounted with the sensor faces horizontal, either to avoid
air bubbles passing through the gap or for convenience of installation. In this case the
switching level will be at the sensor face at the top of the gap.
2.3 Installation of sensor
The sensor must be handled with care - it is a measuring instrument. Before installation,
check that sensor, cable and control unit have not been damaged in transit. Drill and
tap a hole with a suitable thread. It is advisable to use a boss or similar on thin walls.
The sensor has a tapered thread. Use Ptfe tape or similar to seal the thread. Mark the
sensor hexagon to identify the gap orientation of the sensor, if appropriate. Take care
not to damage the sensor cable during tightening.
The cable should be laid on cable trays and separated from any high voltage or mains
cables. The normal cable termination is a plastic gland (to fit the MCU200 control box
drilled hole) and crimped terminal pins to suit the MCU200 terminals.
2.4 Extensions cables
Extension cables up to 50 metres long can be fitted to most Mobrey ultrasonic sensors
in the factory to special order but a better site arrangement is to have a separate ex-
tension cable. Table 1 shows a list of suitable extension cables.
Suitable extension cables
50 m 50 - 100 m Above 100 m
RG174
RG178
URM76
RG58
Consult Aalborg Industries
Table 1
OIL DETECTION EQUIPMENT OM9410_01#A.2
Language UK 15-3 / 11
When double coaxial cable needs to be extended, two sets of coaxial plugs and sockets
will be needed, one set for transmit and one receive. Care must be taken that the con-
nectors are not connected to earth or shorted together in any way, to prevent cross-talk
or pick-up. The coaxial connections must be made in a waterproof junction box. Ter-
minal blocks should not be used.
The extension cable needs to be of 50 Ohm characteristic impedance. Suitable dual
coaxial extension cables can be purchased from Aalborg Industries. For extensions
over 50 metres it is recommended two runs of single coaxial low loss cable is used,
with the transmit and return cable runs separated by 0.15 metres to minimise cross-
talk.
If several sensor cables are being run together then all the transmit cables (those con-
nected to E2) should be grouped together and all receive cables (those connected to
1E) grouped together maintaining the separation specified above.
Two cables are required per sensor. The RG178 should be used where the cable itself
is subject to temperatures exceeding 74C.
3 Control unit installation
3.1 Mechanical
The control unit is supplied with three holes drilled in the bottom (longer) side of the
box. Two glands are supplied for the power input cable and relay output cable. The
sensor is normally supplied fitted with a suitable gland on the cable. Two further holes
can be drilled in the bottom side of the box should these be needed: it is recommended
that the circuit board is removed whilst drilling extra gland holes.
Figure 2 shows the dimensions of the MCU200 housing box.
OIL DETECTION EQUIPMENT OM9410_01#A.2
15-4 / 11 Language UK
MCU200 Housing dimensions
Figure 2 om9410_01_mobreyx0063080en.wmf
All cable connections are made to the terminal blocks along the bottom edge of the
pcb, see Figure 3. Release the terminal screw before inserting the wire.
MCU201 PC board
Figure 3 om9410_01_mobreyx0063090en.wmf
3.2 External connections
OIL DETECTION EQUIPMENT OM9410_01#A.2
Language UK 15-5 / 11
3.2.1 AC mains
AC mains is connected between the N terminal for neutral and one of the 115V
or 230V terminals depending on the voltage supply available - BEWARE - the ter-
minal not connected externally will be live once the transformer is powered via the
other terminals.
3.2.2 Mains earth
Mains earth should be connected to the terminal marked E. This provides an earth
contact for the pcb mounting pints.
3.2.3 The relay
The relay output connections are labelled:

NC - Normally closed (relay de-energised)

C - Common

NO - Normally open (relay de-energised)

There are also two sets of contacts for DPCO relay, labelled 1 & 2.
3.2.4 The sensor
The sensor connections are labelled "1", "E" for the receiver crystal and "2", "E" for
the coax cable to the transmitter crystal. The screens of these coax cables are connected
to the terminals marked "E".
3.2.5 The auxiliary input
The auxiliary input is a terminal which can be connected to a "push to reset" button to
achieve a latching alarm, or to another Mobrey Control unit, to give a pump control
from the MCU200 unit relay output. If a short circuit is connected between terminals
3 & 4, the MCU200 relay, once de-energised, is held de-energised. Even if the sensor
attached to the MCU200 changes state, to that which should energise the output relay,
this relay will not energise until the link between terminals 3 & 4 is broken in the circuit
external to the MCU200.
3.3 Switch settings in MCU200 series
3.3.1 Gain switch and potentiometer
See section 4.
3.3.2 Frequency selection
This slide switch is labelled "FREQ" and is located between the sensor terminal block
E2, and the Aux. input terminals. This selects the operating frequency of the MCU200
oscillator, which for the present installation must be set to 3.7 MHz (switch in the up
position). The setting required is dictated by the sensor type connected to the control
unit.
OIL DETECTION EQUIPMENT OM9410_01#A.2
15-6 / 11 Language UK
3.3.3 Cable check option selection
This slide switch is located directly above the sensor terminal block E2. It is labelled
"Cable Check" and the ex factory setting is "OUT" with the slide switch to the right.
By sliding this switch to the left, the cable check circuitry is brought into action. This
circuitry monitors the continuity of the screens of the two coaxial cables attached to
the sensors: normally these are linked at the sensor to the metal body of the fitting (or
to each other in the case of non metallic sensors). If this continuity is broken, the
"FAULT LED" will illuminate giving an indication that the sensor cable is damaged,
and the MCU200 will give the "ALARM" output relay state (see Figure 4).
3.3.4 Relay output and LED logic selection
The bank of six slide switches towards the top of the pcb sets the relay output state
logic relative to the sensor state, associated time delays and the LEDs. These are slide
switches, best adjusted with a pencil, and the ex factory wetting is with all switches to
the right.
Each switch is colour coded as shown in Figure 4, and the PC board labels give brief
function information.
Relay output and LED logic switch
Figure 4 om9410_01_mobreyx0063130en.wmf
Note: At Figure 4 OSC means sensor oscillating. E means relay energised, NE
means de-energised.
Set the switches in the following order, starting at the bottom and working upwards:
BLUE:
If the MCU200 relay is to be energised (E) when the sensor is oscillating (OSC) then
set the No 6 blue switch to the right (OSC=E). This is the preferred setting, to give a
de-energised relay in the ALARM state for a gap sensor as a low level alarm.
OIL DETECTION EQUIPMENT OM9410_01#A.2
Language UK 15-7 / 11
GREEN:
This selects the relay change which is subject to the time delay selected on the top
switches. When the No.5 green switch is set to the right, the delay occurs between the
sensor changing state and the relay de-energising or becoming not energised (NE).
This time delay is a minimum of 0.l5 seconds, (achieved by switching the top BROWN
switch to the right) and is used to prevent relay chatter at the changeover point. Longer
time delays are selected on the top three slide switches as shown in Figure 5.
The relay change in the opposite direction is immediate (within 50 milliseconds).
The top three slide switches
Figure 5 om9410_01_mobreyx0063100en.wmf
YELLOW:
Only one of the GREEN or RED LEDs will be illuminated at any one time. These
LEDs show the state of the MCU200 output relay. The RED LED is labelled "ALARM"
and the GREEN LED is labelled "NORMAL". The yellow slide switch (Number 4)
determines which LED will be illuminated when the relay is energised (E). It is usual
to have the GREEN/NORMAL condition occur with the relay energised, i.e. with
switch Number 4 to the right (E=GREEN).
4 Applications
4.1 Gain adjustment
Correct adjustment of the gain (HI/LO switch and potentiometer) is essential for proper
operation of any ultrasonic sensor system. This adjusts the gain of the feedback am-
plifier in the control unit, which produces oscillation of the sensor when the coupling
between the ultrasonic crystals is sufficient. Therefore the higher the gain setting, the
lower the coupling needed to produce an oscillating sensor.
The universal control unit of the MCU200 operates with many sensors, so the correct
setting for the particular sensor and application should be found on site by experiment,
if possible. This will take account of particular site conditions like RF coupling between
extension cables, which can affect the maximum allowed gain. Other liquid charac-
teristics, such as presence of suspended solids, or air bubbles, can mean that for reliable
operation the MCU200 gain must be set as high as possible, to overcome future solids
OIL DETECTION EQUIPMENT OM9410_01#A.2
15-8 / 11 Language UK
build up, but at least one potentiometer division below the maximum allowed level, to
ensure temperature and component ageing stability.
The particular procedures outlined below for gain adjustments give the mid point gain
settings, which may need to be adjusted to meet specific site/sensor future requirements
as indicated above.
4.2 Interface detection
4.2.1 Interface detection between two dissimilar liquids
Viscous liquids, emulsions and liquids containing solid particles have a greater ultra-
sonic attenuation than clear liquids. This technique is used to detect which liquid is
present at the sensor, for example for the separation of oil and water. For this duty
Mobrey 402 sensors are used, operating at 3.7 MHz to produce the maximum ultrasonic
difference between two liquids monitored.
The gain is adjusted so that the sensor oscillates only in the liquid with the lower
ultrasonic attenuation: this is usually the clearer liquid (water in the example of Fig-
ure 6). Note that the signal when oil is present in the sensor gap will be the same as
that for air in the gasp, and that emulsion layers give a very high attenuation.
Mobrey 402 Sensor as oil/water interface
Figure 6 om9410_01_mobreyx0063110en.wmf
Step A: Reduce the gain potentiometer with the sensor immersed in one of the liquids
until a "false dry" indication is obtained. Note the position of the pot.
Step B: Repeat for the sensor immersed in the other liquid.
OIL DETECTION EQUIPMENT OM9410_01#A.2
Language UK 15-9 / 11
Step C: Set the potentiometer half way between these two values. Correct perform-
ance requires a total difference between the two set points of at least 3 di-
visions.
Interface detection between two immiscible similar liquidsWhen liquids are
ultrasonically very similar - as happens for example with paraffin or oil and
water - the procedure in section 4.2.1. produces very little difference between
the two "false dry" points. In this case the "reflection" method of interface
detection is used. An illustration of this method is shown in Figure 7.
Note: The Mobrey 402 sensor in the hot well tank is installed as shown in Fig-
ure 7.
If an ultrasonic beam is transmitted from one liquid to another at a suitable angle (10%)
it is split at the interface into a reflected and a refracted beam, so that it does not reach
the receiver crystal. If there is no interference in the gap, but only one liquid, the beam
is received and the sensor oscillates.
Interface detector by reflection method
Figure 7 om9410_01_mobreyx0063120en.wmf
The gain adjustment is made so that the gain is 3 divisions higher than the highest false
dry position obtained, as in section 4.2.1. Performance at the interface should then be
checked.
Note: That the non oscillating state of the sensor, at the interface, also occurs
throughout any emulsion layer at the interface, and also when the sensor
is in air.
OIL DETECTION EQUIPMENT OM9410_01#A.2
15-10 / 11 Language UK
5 Spares and fault finding
5.1 Spares
The following parts are suitable for replacements on the MCU201:

Main pcb complete: K2641

LED indicator pcb: K2643

LED pcb spacers: K2623

LED pcb connector: K2624/50

Box assembly: K2662

Gland Assembly: K746/K747/K748

There are no consumable items such as fuses.
5.2 Fault finding
Step A: At least one LED should be illuminated. If not check the power supply to
the unit.
Step B: If the "Fault" LED is on, check the coax cable to the sensor for incorrect
wiring or damage. Particularly check continuity of extension cables, con-
nection of crimped connectors on cable ends. The pcb board can be checked
by linking the two terminals labelled E on the sensor terminals - this should
cancel the fault indication LED.
Step C: If the sensor is giving incorrect indications check the gain adjustment (see
section 4.0).
Check for correct sensor operation whenever the gain is adjusted away from the normal
set point. Assume an overlap of 2 divisions between the "LO" and "HI" gain ranges.
Step D: Check that the incorrect operation has not been produced by incorrect setting
of the frequency selection switch, or an external short circuit on the Auxiliary
input terminals.
Step E: The circuit board can be checked by linking the sensor terminals 1 and 2
with a wire, to simulate an oscillating sensor.
OIL DETECTION EQUIPMENT OM9410_01#A.2
Language UK 15-11 / 11
Table of contents
Salinity alarm equipment
Description Document ID Page
.
Salinometer, type SL 700............................................ OM8210_34.............. 16-2
TABLE OF CONTENTS
Language UK 16-1 / 5
Salinometer, type SL 700
1 Description
The salinometer is used in combination with a conductive electrode to measure and
supervise the salinity of feed water. Figure 1 illustrates the control device and electrode.
The control device is provided with indication LEDs for monitoring the salinity level
and two LEDs for alarm purpose. The measuring range as well as the adjustable alarm
range is 0 100 ppm (sea salt). The alarm limit can be adjusted by means of the set
screw located on the front panel. The alarm limit is indicated by a flashing LED in the
indication LED row. If the salinity level exceeds the alarm limit the alarm LEDs start
flashing.
During commissioning it is not necessary to carry out any adjustments of the equipment
except setting the alarm limit. When the power is turned on, the salinometer will per-
form a self test. This calibration will take approximately 5 sec.
Illustration of the control device
Gold-plated
electrodes
Packing
Control
device
Connector
plug
Indication
LEDs
Terminals
Figure 1 sl700c_ax0478130en.wmf
SALINOMETER, TYPE SL 700 OM8210_34#C.1
16-2 / 5 Language UK
2 Installation
The conductive electrode may be installed vertically, horizontally, or radial inclined.
However, the electrode tips must be constantly submerged in feed water. Figure 2
illustrates the salinity system.
Illustration of the salinity system
Hot well
Condensate
Make-up
PI PI
Feed water
pumps
PI PI
PS
To boiler
T-piece
Electrode
Salinometer
Junction box
(not AI supply)
Figure 2 om8210_34_sl700dx0058920en.wmf
SALINOMETER, TYPE SL 700 OM8210_34#C.1
Language UK 16-3 / 5
2.1 Wiring
The wiring should be carried out in accordance with the diagram shown in Figure 3.
Wiring diagram
4 1 2 3 5
Junction box
(not AI supply)
1
2
3
4
5
6
G
r
e
e
n
W
h
i
t
e
R
e
d
S
h
i
e
l
d
B
l
a
c
k

G
r
e
e
n
W
h
i
t
e
R
e
d
S
h
i
e
l
d
B
l
a
c
k
Plug: 6 pol GLC
Figure 3 821034wiringx0208340en.wmf
The mains supply of the control device is 90-115 VAC or 190-230 VAC, 50-60 Hz.En-
sure that the mains supply is secured against over current by a fuse (max.100mA).
The recommended cable for the conductive electrode is a multi-screened twin twisted
pair like Farnell no. 385-4334, where the screen is connected to connector 14, one pair
is used for connector 11+12, and the other pair is used for connector 13+15. The length
of the cable must not exceed 200 m.
Important: The cable may not be placed together with power cables, as this will
cause damage to the gold plating on the electrodes.
SALINOMETER, TYPE SL 700 OM8210_34#C.1
16-4 / 5 Language UK
3 Maintenance
The accuracy of the salinometer equipment is very dependent on the electrodes are
kept clean. The electrodes should be taken out and cleaned at least once a week. Use
only a clean and soft reg. When cleaning the electrodes it is important that oil or other
chemicals do not pollute the electrodes. Any pollution will immediately result in an
inaccurate measurement of the salinometer.
Note: Avoid damaging the gold plating.If the gold plating is damaged, the con-
ductive electrode must be replaced.
The expected longevity of the conductive electrode is approximately 1.2 2.2 years.
SALINOMETER, TYPE SL 700 OM8210_34#C.1
Language UK 16-5 / 5
Table of contents
Descriptions
Description Document ID Page
.
Pressure jet burner, type KBO-E.................................. SD5560_12............... 17-2
TABLE OF CONTENTS
Language UK 17-1 / 3
Pressure jet burner, type KBO-E
1 Burner description
The KBO-E burner is a pressure jet burner of the monoblock type designed for mod-
ulating operation. It is capable of burning marine diesel oil, MDO with a viscosity of
min. 4 cSt. at 20C. Marine gas oil with a viscosity of min. 1.5 cSt. at 40C. And heavy
fuel oil HFO, with a viscosity of max. 700 cSt. at 50C. All internal pipes are traced.
The design of the burner makes installation, adjustment and servicing easy. Further-
more, it ensures that the flame is kept highly stable at all loads. An illustration of the
KBO-E burner is shown in Figure 1.
Illustration of the pressure jet burner, type KBO-E
Figure 1 kbo-ex1301530en.jpg
The burner housing is mounted on the boiler front with a hinged flange that can be
turned either to left or right. In case of burner swing out during operation a micro switch
stops the burner.
The electrical fan motor is fitted on the side of the housing and is directly connected
to the fan wheel. A pressure switch monitors and secures against too low combustion
air pressure. In case of too high oil pressure after the oil regulator a pressure switch
shuts down the burner.
A combustion head and diffuser disc are placed in front of the nozzle with the purpose
of mixing air and oil mist into a suitable mixture.
PRESSURE JET BURNER, TYPE KBO-E SD5560_12#F.1
17-2 / 3 Language UK
The oil is supplied through a ring line system and connections to the burner unit are
made of flexible hoses.
Heavy fuel oil is heated in the pre-heater. The oil atomising temperature is controlled
by an electronic regulator which has to be set so that the viscosity of the heavy fuel oil
at the nozzle is between 14 16 cSt.
Heating cartridges are placed in the solenoid valves and nozzle head in order to keep
a sufficiently high temperature close to the nozzle.
The burner operation is handled by the control system. Electric signals corresponding
to the pressure gauge board signals are processed in the control system. Start/stop
signals as well as load regulation impulses are then send to the two servo motors, which
drive the oil regulator and air dampers respectively.In the event of fault conditions the
oil supply is always interrupted immediately.
The oil regulator regulates the oil flow through the nozzle by increasing or decreasing
the flow resistance. This causes that more or less oil is pressed through the nozzle as
the supply pressure from the oil pump is constant. The air dampers are connected
directly to the second servo motor. The control system provides the regulation of the
air quantity in proportion to the oil quantity fired.
When the burner starts, and the ignition sequence step is reached, the oil flame is ignited
by means of the two ignition electrodes which are connected to a high voltage ignition
transformer. The electrodes are mounted just above the oil nozzle.
Flame failure during start-up and normal operation is detected by photo cells mounted
on the burner unit and coupled to the control system. By loss of flame, the flame failure
equipment will automatically shut down the burner.
PRESSURE JET BURNER, TYPE KBO-E SD5560_12#F.1
Language UK 17-3 / 3
Table of contents
Installation
Description Document ID Page
.
Mounting and connection of the burner........................ IN5560_03................ 18-2
TABLE OF CONTENTS
Language UK 18-1 / 9
Mounting and connection of the burner
1 Description
The following section describes the installation of the burner and the connection of the
fuel oil supply system.
1.1 Mechanical mounting of the burner
When the boiler plant is delivered, the front plate for the burner is delivered loose
including packing and bolts.After the pressure part of the boiler plant is installed, the
following work procedures must be followed in order to mount the burner unit,
seeFigure 1 and Figure 2.
Note: If the burner is stored for a period of time before mounting on the boiler,
it must be stored indoors.
Step A: Ensure that the transportation support mounted on the fire hole is removed.
Step B: Mount the frontplate delivered with brickwork, packing and bolts.
Step C: Take out the burner of the transportation box by means of a lifting hanger
placed around the burner.
Step D: Dismount the swirl flange including combustion head.
Step E: Mount the packing on the front plate of boiler (packing included).
Step F: Mount the complete swirl flange and combustion head on the front plate by
using the bolts (bolts included).
Step G: Mount the burner on the swirl flange by using the swing bolt. As standard
the burner is hinged to the left. The burner can, however, be changed to be
hinged to the right by changing the position of the hinge pins.
Step H: Lock the oil burner by means of the delivered closing bolt.
Step I: Mount the flexible oil hoses between the fuel quick closing unit and the
burner unit.
Step J: Connect the pipe for scavenging air on top of the oil burner. The scavenging
air must be taken from the burner fan and the connection piece should be
mounted just behind the hinged flange on the burner.
Step K: Mount the support leg on the burner according to Figure 3. Adjust the spindle
so the leg is supporting the burner not lifting it. Weld the support leg to the
deck to secure its position.
Note: Step K is for burner size 40M to 60M only.
Step L: The combustion head of the burner should be adjusted according to the in-
structions of the burner.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
18-2 / 9 Language UK
Mounting of the front plate
Figure 1 in5560_03_burn_ox0051850en.wmf
Mounting of the burner on the pressure part
Scavenging air tube
Swing bolt
Swirl flange and
combustion head
Burner
Front plate
Figure 2 in5560_03_osin_1x0051860en.wmf
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
Language UK 18-3 / 9
Installation of support leg for burner sizes 40M ton 60M
7
5
0
1
4
0
0

t
o

2
0
0
0
Figure 3 kboe_legx1234820en.wmf
1.2 Pipe connections
The pipe dimensions between the oil pump(s) and the burner unit should be dimen-
sioned so that the velocity inside the suction pipe does not exceed 0.5 m/s and so that
the velocity inside the pressure pipe does not exceed 1.0 m/s.
The oil pressure in the ring-line must as a minimum be 30.0 bar, and as a maximum
33.0 bar.
Attention: Pressure testing with water is not allowed.
1.3 Flexible Hose connection
The flexible hoses delivered with the burner have to be mounted according to the
specifications. The distance between the ring line connection and the connection points
on the burner has to be smaller than the length of the flexible hoses minus 200 mm.
Please see the belonging datasheet for the dimensions on the delivered flexible hoses
and burner.
The minimum bending radius for the flexible hoses is 130 mm, see example 2.
1.3.1 Avoidance of torsion stress.
When installing the hose line, tighten the hose firmly at one end and swivel only at the
other end. Move the hose in the desired direction two or three times without load to
enable the hose to align free of torsion. Then tighten the connection. With threaded
fasteners, a second spanner will in all circumstances be required for countering. When
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
18-4 / 9 Language UK
determining the fittings, make sure that at least one end of the hoses is fixed by a swivel
connection. See the following examples.
Example 1
Figure 4 burn_instal_hosex0200270en.wmf
- Connect hose line free of torsion. Use a second spanner for countering in threaded
swivel fasteners.
Example 2
Figure 5 burn_instal_hosex0200280en.wmf
- When installing hose line at 180 bend, leave neutral hose ends long enough
Example 3
Figure 6 burn_instal_hosex0200290en.wmf
- Avoid too sharp deflections directly behind the fittings by using rigid pipe bends.
Observe the minimum bending radius.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
Language UK 18-5 / 9
Example 4
Figure 7 burn_instal_hosex0200300en.wmf
- To avoid torsion stress, the direction of movement and hose axis have to lie in one
plane.
Example 5
Figure 8 burn_instal_hosex0200310en.wmf
- Direction of movement and hose bend should lie in one plane to avoid torsion.
Example 6
Figure 9 burn_instal_hosex0200320en.wmf
- Avoidance of alternating bending stress and excessive buckling directly behind
the fittings by application of rigid pipe bends.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
18-6 / 9 Language UK
Example 7
Figure 10 burn_instal_hosex0200330en.wmf
- Install hose avoiding contact with the wall even at maximum extension.
Example 8
Figure 11 burn_instal_hosex0200340en.wmf
- When installing at a 90 bend, observe that the permissible bending radius and
neutral hose ends are long enough. Excessive bending and stretching of the hose
must be avoided.
Example 9
Figure 12 burn_instal_hosex0200350en.wmf
- Install hose at right angles to the direction of vibration.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
Language UK 18-7 / 9
Example 10
Figure 13 burn_instal_hosex0200360en.wmf
- If vibrations occur in all directions, install hoses as an angular hose line at 90. A
single hose will not absorb axial vibration.
Example 11
Figure 14 burn_instal_hosex0200370en.wmf
- For absorption of heat expansion the hose is installed at a 90 bend with straight
legs which are long enough. Hose bend and direction of movement must be in one
plane.
Example 12
Figure 15 burn_instal_hosex0200380en.wmf
- Lateral installation is permissible for absorption of low expansion only. Stretching
or compressing of the hose must be avoid.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
18-8 / 9 Language UK
Example 13
Figure 16 burn_instal_hosex0200391en.wmf
- For absorption of higher expansion, install the hose at 90 bend. Lateral movement
must be avoided.
1.4 Electrical connections
The internal electric cables are pre-mounted on the burner. When the boiler unit is
delivered the electrical cablesbetween the control system and burner unit must be con-
nected as described below.
Step A: Remove the cover mounted on the burner.
Step B: Mount the cables through the cable glands on the burner.
Step C: The cables must be of sufficiently length to ensure free burner swing out.
Step D: The terminal rows are marked with numbers.
Step E: Connect the cables from the control system to the marked/numbered termi-
nal rows according to the electrical drawings.
MOUNTING AND CONNECTION OF THE BURNER IN5560_03#B.1
Language UK 18-9 / 9
Table of contents
Fuel oil pump unit
Description Document ID Page
.
Oil pumps, type SPZ.................................................. OM9295_02.............. 19-2
TABLE OF CONTENTS
Language UK 19-1 / 25
Oil pumps, type SPZ
1 General
The SPZ pumps series are employed for handling light and heavy fuel oil. The twin
aggregate is constructed as a compact type in which two screw pumps are intercon-
nected by way of a reversing valve casing.
1.1 Abbreviation
The abbreviation of the screw pump twin aggregates is set up according to the following
scheme:
Example: SPZ 10 R 38 G 8.3 FE-W20
Where:

SPZ: series

10: size (theoretic delivery in [l/min] with 1450 1/min and 46 degrees pitch angle

R: direction of screw pitch (R = right)

38: angle of screw pitch (degrees)

G: kind of bearing (internally slide bearing)

8.3: shaft sealing by mechanical seal

F: design with filter

E: design with electric filter-heating of the filter casing

W20: material design

1.2 Warranty
Our liability for shortcomings in the supply is laid down in our delivery conditions.
No liability will be undertaken for any damages caused by non-compliance with the
operating instructions and service conditions. If at any later date the operating condi-
tions happen to change (e.g. different fluid conveyed, speed, viscosity, temperature,
or supply conditions), it must be checked by us from case to case and confirmed, if
necessary, whether the pumps are suited for these purposes. In case no special agree-
ments were made, the pumps supplied by us may, during the warranty period, only be
opened or varied by us or our authorised contractual service stations; otherwise, our
liability for any defects will expire.
1.3 Testing
Prior to leaving our factory, all aggregates are subjected to a thorough test run and
performance test on the test stand. Only properly operating pumps leave the factory
achieving the performances assured by us. Thus, compliance with the following op-
erating instructions ensures proper operation and full delivery.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-2 / 25 Language UK
1.4 Performance data
Delivery, Q: up to 6.7 m
3
/h (with n = 2900 l/min and v = 750 mm
2
/s.)

Temperature of the fluid pumped, t: up to 150C (with higher temperatures, please

inquire)

Inlet pressure, ps: up to 5 bar

Pump outlet pressure, pd: up to 40 bar (For the attainable delivery pressure as a
function of viscosity and speed, please refer to the individual characteristics. The
pressure data only apply to nearly static pressure load. With dynamic pressure
change load, please inquire.)
Viscosity range,v = 3 to 750 mm
2
/s

Pressure flange, DNd = 20 to 40 mm

The exact performance data applicable to the pump can be taken from the layout and/
or acceptance certificate, and are engraved on the rating plate.
1.5 Application and installation
The screw pump twin aggregates of series SPZ for a pump outlet pressure up to 40 bar
are three-screw, self-priming, rotary positive displacement pumps for handling lubri-
cating fluids. The fluids must not contain any abrasive particles nor chemically attack
the pump materials.
Both pumps of the aggregate are designed as flange-mounted pumps and via pump
bracket each connected with the driving motor.
Attention: The aggregates are provided for horizontal installation or wall mount-
ing. For safety purposes, the arrangement with motor down-wards
is not admissible.
2 Structural design
The screw pump twin aggregates of series SPZ consist of two screw pumps. Sectional
drawings of the pump are shown in Figure 1 and Figure 2. The item numbers referred
to in this section are those indicated on these drawings.
Via a reversing valve casing (301), the two pumps are connected with each other.
The screw pumps are of the three-screw type. A double-threaded driving spindle (12)
and two double-threaded idler spindles (13) are enclosed by the bores in the pump
casing insert (2) with a narrow running clearance. The pump casing (1) accommodates
the pump casing insert (2) and is closed by the pump cover, drive side (3) and by the
pump cover, non drive side (4) and the filter casing (9).
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-3 / 25
Sectional drawing of the SPZ pumps, without filter
Figure 1 om9295_02_spz01x0060170en.wmf
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-4 / 25 Language UK
Sectional drawing of the SPZ pumps, with filter
Figure 2 om9295_02_spz02x0060180en.wmf
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-5 / 25
2.1 Shaft seal
The pump has a maintenance-free mechanical seal of the unbalanced type.
Material design of the mechanical seal:

Rotating seal ring: tungsten carbide

Stationary seal ring: tungsten carbide

Joint ring: Viton

Spring: stainless steel

Metal parts: stainless steel

2.2 Bearing and lubrication
The radial and axial bearing of the driving spindle of a screw pump is effected by the
bearing ring. At the same time, the delivery chamber is separated from the sealing
chamber by the gap between the compensating piston and bearing ring. The bearing is
lubricated by the fluid pumped.
2.3 Flanges / connections
Blank flanges with screw and gaskets.

Suction side: PN 16, DIN 2633

Outlet side: PN 40, DIN 2635

Connections:
- SPZ without filter: M1, M2 manometer
- SPZ with filter: B7 draining filter casing, E7 venting filter casing, M1, M2, M3
manometer
2.4 Filter
As a protection against contamination, the pumps can be equipped with a filter casing
and an incorporated filter. Filter mesh size 0.4 mm.
The mano/vacuum-meters being part of the scope of supply show the pressure behind
the filter. By means of these, the pressure loss in the respective filter can be detected,
and an inadmissible contamination recognised.
2.5 Electric heating
In case of design with filter, ring heaters may be provided for filter heating.
Pump size Connection for Heating capacity
SPZ 10 220 V 165 W
SPZ 20 220 V 205 W
Table 1
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-6 / 25 Language UK
2.6 Pressure relief valve
As an overload protection, a pressure-relief valve is installed in each pump, which is
serially set to a response pressure approx. 10% above the operating pressure.
2.7 Non-return valves / stop valves
In the reversing valve casing, a non-return valve and a stop valve are provided for each
pump. The non-return valves operate automatically and can be locked by hand.
2.8 Operation control
Manometers:

SPZ pump without filter:

- Outlet side: a manometer (included in the scope of supply). If a mano/vacuum
meter is requested on the suction side, this must be provided at the side. For con-
nection, the bore for the screw plug (227) is provided.

SPZ pump with filter:

- Suction side: two mano/vacuum-meters
- Outlet side: one manometer
Reversing unit:
If a reversing unit was supplied for operation control, its circuitry is such that in case
of failure of the operating pump the stand-by pump is automatically switched on. Signal
lamps denote the respective operating conditions.
Reversing unit U1: for motors up to 3 kW (380 V operating voltage) for across-the-
line-starting.
Reversing unit U3: for motors up to 3.0 and 5.5 kW (380 V operating voltage), suited
for star delta-starting.
2.9 Oil trough
The twin aggregate is provided with a separately supplied oil trough.
2.10 Drive / coupling
Via the pump brackets flanged to the pumps, electric motors of the most varied designs
are connected with the pumps. In the normal case, these are attached:
Surface-cooled three-phase squirrel-cage induction motors, IMV1 type of construc-
tion, enclosure IP 44 according it IEC Standard, class B insulation, performances and
main dimensions according to DIN 42 677.
Motors which are rated for 50 Hz can, without change, be operated also in 60 Hz mains,
speed and performance are changed as shown in Table 2.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-7 / 25
Power transmission is effected via a flexible coupling. Additional radial forces must
not act on the driving spindle. The pump brackets serve as protection against accidental
contacts according to DIN 24 295.
Attention: Drive via belt or gear wheel is not admissible.
Motor wound for 50 Hz Connection for 60 Hz Conversion factor for operation at 60 Hz
V V Speed Performance
220 V 220 V 1.2 1.0
380 V 380 V 1.2 1.0
380 V 440 V 1.2 1.15
440 V 440 V 1.2 1.0
Table 2
3 Mode of operation
3.1 Mode of operation of the screw pump twin aggregate
Switching diagrams showing the screw pump twin aggregate can be seen in Figure 3.
Switching diagrams
Figure 3 om9295_02_spz03x0060190en.wmf
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-8 / 25 Language UK
Both screw pumps are jointly attached to the reversing valve casing (301). While one
pump is in operation, the stand-by pump is at standstill.
The pumps can be connected alternately by hand or automatically by means of a re-
versing unit (U1 or U3). By way of two separate connecting chambers in the reversing
valve (301), the respective two suction flanges and the two pressure flanges of the two
pumps are connected with one another. Uninterrupted delivery during the reversing
process is thus ensured.
During operation, the two lockable non-return valves (356) and the two stop valves
(355) must be opened so that reversal is optionally possible from the one pump to the
other. The respective connected pump draws the fluid in through the suction chamber
of the reversing valve casing (301). The operating pressure built up in the delivery
chamber of the pump opens the non-return valve (356) of the operating pump and,
through the pressure in the delivery chamber of the reversing valve casing (301), closes
the non-return valve (356) of the non-operating pump. This prevents the stand-by pump
from running in reverse motion.
3.2 Mode of operation of the screw pumps
Through the suction chamber in the reversing valve casing, the material to be pumped
is conveyed into the suction chamber of the pump in operation. From here, the fluid
flows into the spindle chambers which are constantly formed by the rotary motion at
the spindle end on the suction side. By the translatory rotary motion, the chambers
filled with the fluid to be conveyed move from the suction side to the outlet side. During
this process, the closed chamber volume does not change. At the spindle end on the
outlet side the chamber opens towards the delivery chamber. The fluid conveyed is
steadily pushed out into the delivery chamber from where it is transported, through the
delivery chamber, into the pressure pipeline. The axial thrust acting on the faces of the
profile flanks on the outlet side is hydraulically balanced by an appropriate dimen-
sioning of the compensating piston of the driving spindle. Thus, the bearing is relieved
from the hydraulic axial thrust. By appropriate dimensioning of the spindles, the drive
of the idler spindles is hydraulic. Only the torque resulting from the liquid friction is
transmitted via the profile flanks; therefore, they are practically stress-free and not
subject to any wear. The axial thrust of the idler spindles is absorbed by the pump
cover, non-drive side or by the filter casing. Sealing chamber and suction chamber are
interconnected via a return bore. Therefore, irrespective of the delivery pressure, only
the suction pressure acts on the shaft seal. All sliding parts are lubricated by the fluid
to be pumped and are within the range of full liquid friction. In spite of spindle rotation,
there is no turbulence. The constant chamber volume excludes squeezing.
The structural design and the mode of operation of the screw pumps ensure a very low
noise level and an almost pulsation-free delivery.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-9 / 25
4 Preservation and storage of the pumps
4.1 Preservation
If required, the screw pumps delivered by us are already provided with the requested
preservation protection according to the storage time specified by the customer. Also
in case of prolonged shutdown, the screw pumps must be protected against corrosion.
In those cases, an outside and inside preservation is to be provided. The durability of
the protection against corrosion which is limited in time, depends on the composition
of the preservative to be applied. It is therefore recommended to use such preservatives
only which have a minimum durability of 12 months. Below is listed preservative
which can be applied for both outside and inside preservation.
4.1.1 Outside preservation
All bright and unvarnished parts such as: shaft ends, couplings, flange facings, valve
and manometer connections can be preserve with one of the following preservative:

TECTYL 506

A mixture of TECTYL 506 and TECTYL 511-M1

This preservative is to be applied by painting or spraying with a spray gun.
4.1.2 Inside preservation
Pump casing inside, screw spindles, ball bearing, pressure-relief valve, mechanical
seal can be preserve with:

Mixture of: TECTYL 506 and TECTYL 511-M1

Note: The preservative listed above is to be regarded as a recommendation.
Preservatives having the same preserving properties can also be used.
The preservative is to be applied by filling the pump. For these purposes, the suction
side of the pump must first be closed with a dummy flange. During filling, the pressure
flange must be on a higher level than the suction flange. During the filling process, the
driving spindle must be slowly cranked against the sense of rotation. Filling must be
continued until the preservative reaches the sealing strip of the delivery flange, bubble-
free. Thereafter, the outlet side is to be closed with a dummy flange.
4.1.3 Control of preservation
In case of prolonged storage, the preservation of the pump must be checked by the
customer at regular intervals.
Step A: Every six months, the pump level must be checked, if necessary, preservative
must be topped up to the sealing strip at the pressure flange.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-10 / 25 Language UK
Step B: At the same time, the packing must be checked for destruction, and repaired,
if necessary.
Note: Liability for damages caused by improper preservation cannot be predic-
ted.
4.1.4 Durability of the preservative
According to the preservative manufacturer, the durability of TECTYL 506 is 4 to 5
years in case of indoor storage, and 12 to 24 months in case of outdoor storage, and of
TECTYL 511-M approx. 18 months in case of indoor storage. When mixing TECTYL
506 and TECTYL 511-M in the same proportion, a durability of 2 to 4 years in case
of indoor storage, and a maximum of 12 months in case of outdoor storage under roof
can be expected. With additional packing, the service life is increased.
The active ingredients contained in this preservative provide sufficient protection
against corrosion even in high air humidity (sea, tropical climate). Therefore, a tem-
perature limitation (+ and -) does not exist.
4.1.5 Degreasing
Prior to setting the screw pump in motion, the preservative applied must be removed.
The preservative applied for inside preservation can normally be removed by flushing
the pump with the fluid to be conveyed. In addition, a suitable solvent may be applied
for removing the inside and outside preservation.
Appropriate solvents can be: Petroleum, benzene, Diesel fuel, spirit, alkalis (industrial
cleaners) or any other wax solvents. Steam jet cleaning devices with appropriate ad-
mixtures can also be used (allow wax solvent to react previously).
Attention: Prior to start-up, the pump must be filled with fluid to be conveyed
so as to avoid seizing of the spindles during starting.
Note: If on the plant side, the pipelines, (oil) tanks and gear parts in circulation
are wetted with the paraffin-containing preservative, the entire plant must
be degreased as paraffin deteriorates the air separating capability of the
(oil) filling. This may result in unsteady operation of the pump, connected
with a loud noise development.
4.2 Storage
During storage of the screw pump, the suction and outlet branches and all other supply
and discharge branches must always be closed with dummy flanges or dummy plugs.
Storage should be in a dust-free and dry room.
Step A: During storage, the screw pump should be cranked at least once a week.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-11 / 25
Step B: During this process, the screw spindles should each time change their turning
position.
After prolonged storage, all elastomers (O-rings, mechanical seals) must be checked
for their elasticity of shape.
Step C: Embrittled elastomers must be exchanged.
Note: Only proper storage and packing ensure the durability of the preservatives
applied.
5 Foundation design/fastening type
The foundation must be designed so that it can take the weight of the pump aggregate.
Fastening is effected via the foot angle screw-connected to the intermediate lantern.
6 Mounting of the twin aggregate
6.1 Control of the sense of rotation at the driving motors
The sense of motor rotation must correspond to the directional marker of the pumps.
For a control of the sense of rotation, the motors may be alternately switched in tem-
porarily in an uncoupled condition. The sense of rotation being wrong, the pumps do
not prime. This will result in damages to the pumps. The sense of rotation of the re-
spective three-phase motor can be changed by interchanging any two phases.
6.2 Installation of a complete twin aggregate
A twin aggregate supplied complete was carefully assembled at the works. As the
pumps and the driving motors are centred in the pump bracket, re-alignment of the
couplings is normally not required.
Note: Improper handling, for example, during transportation, may affect the
alignment provided between pumps and motors. In this case, the respective
motor must be dismounted from the pump bracket.
Exact examination of the alignment is effected by means of a dial gauge with retaining
clip and clamping device fixed to the driving spindle and motor shaft end. The exami-
nation covers the admissible circular and axial run-out between the shaft ends and the
centring diameters and the plane faces at the pump brackets (0.05 mm admissible as a
maximum).
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-12 / 25 Language UK
6.3 Installation and assembly of pump and driving motor
The aggregate being completed at the place of service only, the coupling must be
assembled as follows:
Step A: Cover pump and motor shaft ends with a filmy coat of molybdenum disul-
phide (e.g. Molykote), and insert keys.
Step B: By means of a mounting device, push coupling halves onto pump and motor
shaft end.
Attention: Axial shock loads on the driving spindle of the pumps and the anti-
friction bearings of the driving motors must be excluded during
mounting of the couplings.
Step C: Re-alignment of the couplings is not necessary (please refer to section 6.2).
6.4 Laying the pipelines
6.4.1 Nominal widths
If possible, the nominal widths of the suction and outlet pipeline should be rated so
that the rate of flow does not exceed 1 m/s in the suction line and 3 m/s in the pressure
pipeline as a maximum.
Note: The nominal diameter of the suction and pressure pipeline must be of the
same size as the nominal pump diameter or one nominal diameter greater.
The nominal diameter on the suction side must never be smaller than the
nominal pump diameter, as suction may otherwise be difficult.
6.4.2 Change of cross-sections and directions
Sudden changes of cross-sections and directions, as well as hairpin bends, must be
avoided.
6.4.3 Supports and flange connections
By way of the flange connections, the pipelines must be connected to the pump stress-
free. They must be supported close to the pump and should allow easy screwing to
avoid deformations. After the screws have been slackened, the flanges must neither be
inclined nor springy nor rest on top of one another under pressure.
Any thermal stresses that may occur at the pipelines must be kept away from the pump
by taking appropriate measures, e.g. by the installation of compensators.
6.4.4 Cleaning of pipelines prior to attachment
Prior to assembly, all pipeline parts and valves must be thoroughly cleaned. Especially
in the case of welded pipelines, burrs and welding beads must be removed. Flange
packing must not protrude inwards.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-13 / 25
Water residues, still in the pipeline network from pressing-out or steeping for example,
must be removed. Delivery of water destroys the pump. The pump relies on the fluid
being conveyed for its lubrication.
At the pressure test of the pipe system the customer is responsible for any damages
and their consequents.
6.4.5 Non-return valves / stop valves
In the reversing valve casing, a non-return valve and a stop valve are provided for each
pump.
Note: With the non-return valve and stop valve closed, filter cleaning of those
pumps may be effected which operate under supply pressure.
6.4.6 Venting
The pumps without filter can be vented via the screw plug (227).
In case of pumps with filter, the venting screw (223) in the filter and the screw plug
(227) serve for venting. In addition, a vent valve must be provided at the highest point
in the pressure pipeline.
Note: In case of horizontal aggregate installation and with the suction and pres-
sure flange turned sideways, the filling and venting bores and/or connec-
tions for the manometers must point upwards.
6.4.7 Filtering
In case of aggregates which do not have filters attached at the factory, it is recommen-
ded to mount a filter in the suction pipeline to protect the pump against solid contam-
ination. Filter mesh and/or gap size 0.1 to 0.5 mm depending upon the degree of con-
tamination of the fluid to be pumped.
7 Preparation for start-up
7.1 Filling the pumps with the fluid to be conveyed
Attention: Prior to initial operation, the two pumps must be filled with the fluid
to be conveyed. At the same time, the sealing required for suction is
imparted to the spindles. The pump must not run dry.
7.1.1 Filling and venting of a pump without attached filter
The with fluid to be pumped is filled in through a filling hole at the suction flange of
the pump.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-14 / 25 Language UK
For these purposes:
Step A: The screw plug (227) with the joint ring (156) must be removed.
The pump must be topped up with the fluid to be pumped until this fluid emerges at
the vent hole of the pressure flange, bubble-free.In case of supply pressure, manual
topping-up is not required. The pump is topped up via the supply pipeline, and vented
via the filling and venting hole.
7.1.2 Filling and venting of a pump with attached filter
Pumps in horizontal installation with attached filter are topped up via the filling hole
in the (filter) casing cover (7) until the fluid pumped emerges at the vent hole of the
pressure flange, bubble-free.
For these purposes:
Step A: The vent screw (223) and the screw plug (227) with the joint rings (143) and
(156) must be removed.
Pumps in vertical installation with attached filter are topped up with fluid to be pumped
via the filling and vent holes in the casing as described under section 7.1.1.
Note: Instead of the screw plugs (227), manometers may be mounted in the suc-
tion and pressure flange of the pump casing (1). Please refer to section 2.3.
7.2 Heating of the fluid to be pumped
When pumping heavy fuel oils or other fluids to be pumped congealing when getting
cold, it is necessary to provide a heating system in the plant (e.g. pipe steam trace).
At the time of pump starting, the fluid to be pumped must be in a flowable and pumpable
condition to avoid damages to the operating pump as well as the stand-by pump.
Step A: Prior to the pump start-up, heavy fuel oil, for example, must be heated to at
least 10C above the solidifying point.
Step B: For twin aggregates, with filters attached at the factory, a filter heating may
be provided. A ring heater serves to heat the filter.
The heating capacity of the ring heaters is designed so that with an initial temperature
of 20C, a minimum heating-up time of 120 min. is necessary. The temperatures being
lower (below 0C), an appropriately longer heating time must be expected. The heating
system is not appropriate for achieving during operation a marked temperature increase
of the fluid to be pumped. The ring heaters must be connected to 220 V (provide parallel
connection, no series connection).
8 Start-up
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-15 / 25
8.1 Starting the operating pump
Prior to starting the operating pump:
Step A: The two stop valves on the suction side and the two lockable non-return
valves on the outlet side of the reversing valve casing, and gate valves, if
any, must be opened in the plant.
A pressure-relief valve is installed in each pump which is serially set on our test field
to a response pressure which is approx. 10% above the operating pressure.
Step B: By means of the adjusting screw (333), the opening pressure can be changed
within narrow bounds.
Attention: When starting and stopping the pump under pressure load, make sure
that the speed and viscosity-dependent pressure load is not exceeded.
If this is not ensued, the pump must be started at zero pressure or
disconnected. This also applies to pumps with speed-controlled driv-
ing motors.
The pressure-relief valve must not be used for regulating the delivery flow.
Step C: During starting, a vent valve on the outlet side of the plant must be opened
until the air has escaped from the suction side of the pump. As soon as fluid
to be pumped emerges, the vent valve may be closed. The pump is self-
priming and is automatically vented without counter-pressure.
8.2 Motor
Step A: Switch motor of operating pump in.
8.3 Checking the delivery values
Step A: After the motor has reached its operating speed, inlet pressure and outlet
pressure of pump must be checked via vacuum gauge and manometer.
The motor must not be overloaded. The power consumption can be checked by means
of an ammeter. In this connection, temperature and viscosity of the fluid must be
checked. The values read must be checked against the layout and/or acceptance report.
Note: Pressure gauges such as vacuum gauges and manometers are normally
equipped with stop valves. The stop valves are to be opened only during
start-up for pressure control purposes. During permanent operation, these
must be kept closed.
9 Stopping and restarting
9.1 Stopping
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-16 / 25 Language UK
9.1.1 Motor
Step A: Switch off motor of the operating pump. Attend to even and smooth slowing-
down of the pump.
9.1.2 Reversing valve casing
The non-return valves and stop valves in the reversing valve casing remain open.
9.2 Restarting
After proper initial operation, the pumps are ready for operation at any time and can
be started without filling.
9.3 Measures in case of prolonged interruption
If a prolonged interruption is projected, the pumps must be drained as described below.
Step A: The screw plug (222) must be removed from the draining bore. Draining of
the filter is effected after loosening of the screw plug (235).
Step B: Thereafter, the pumps must be preserved (please refer to section 4).
Note: After the screw plug (222) has been turned out, the adjusting screw (333)
of the pressure-relief valve must be turned out for drainage. Previously,
by means of a depth gauge, the thread reach of the adjusting screw (333)
in the pump casing (1) must be recorded. When screwing the adjusting
screw (333) in again, this thread reach must be considered in order to reach
the response pressure of the pressure-relief valve again (normally 10%
above the operating pressure).
10 Control of operation and maintenance
Regular control and maintenance works performed at the twin aggregate will extend
the service life. The below-listed details apply in general.
10.1 General control

The pumps must not run dry.

The driving motors must not be overloaded.

Check suction and pressure pipelines for tightness. The admission of air into the
delivery system must be avoided.

The mechanical seal must not be heavily leaking.

Pressure and temperature monitoring instruments must be observed.

10.2 Control of components
Item numbers mentioned in this section refer to the sectional drawings of the SPZ pump
in Figure 1 and Figure 2.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-17 / 25
10.2.1 Bearing and lubrication
Bearing of the driving spindle of each pump is by means of a maintenance-free sliding
bearing lubricated by the fluid pumped.
Under normal operating conditions, the service life of the sliding bearing corresponds
to the lifetime of the screw pump. It depends on the degree of contamination of the
fluid to be handled.
10.2.2 Check couplings
At regular intervals, the couplings must be checked for wear. A worn-out coupling
must be replaced.
10.2.3 Shaft seal
Each pump is equipped with a maintenance-free mechanical seal of the unbalanced
type whose mode of operation corresponds to the requested operating conditions.
A minimum functional leakage in case of non-volatile fluids such as oils must in prin-
ciple be expected. In case of heavy leakage due to wear, the mechanical seal must be
replaced.
Attention: As dry operation of the mechanical seal must be avoided, the pumps
may be started in a filled and vented condition only.
10.2.4 Pressure-relief valve
The pressure-relief valves of the two pumps must temporarily, especially after pro-
longed idle times, be checked for workability and function. Leaky pressure-relief
valves may result in damages to the pump. If necessary, damaged parts must be ex-
changed or replaced.
The pressure-relief valves of both pumps were set to the opening pressure requested
by the customer (normally 10% above the operating pressure). If the opening pressure
is to be changed then:
Step A: The screw plug (222) in the pump cover, non-drive side (4) and/or in the
filter casing (9) must first be removed. Thereafter, the adjusting screw (333)
is accessible.
Step B: Clockwise rotation increases, anti-clockwise rotation decreases the opening
pressure. Re-adjustment should be effected with a perfect manometer only.
10.2.5 Filtering
The twin aggregates of series SPZR..G8.3F have attached filters.
The filter casing (9) is equipped with a mano/vacuum-meter (361) displaying the pres-
sure behind the filter (481). The pressure loss suggests the degree of filter contamina-
tion. For an exact determination of the differential pressure, it is recommended to install
a manometer in the front of each filter at the suction flange of the pumps or in the
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-18 / 25 Language UK
suction and/or supply pipeline. In case of noticeable differential pressure, the filter
(481) must be cleaned or replaced.
Step A: Before the filter of a pump can be cleaned, it must be switched over to the
stand-by pump. Thereafter, the lockable non-return valve (356) and the stop
valve (355) of the pump at rest are to be closed.
Step B: Filter cleaning is effected in that the filter (481) is removed from the filter
casing (9), cleaned, and the dirt particles deposited at the filter casing bottom
are flushed out.
Step C: After the hexagon screws (207) have been slackened, the (filter) casing cover
(7) can be removed and the filter (481) dismounted from the filter casing
(9).
Step D: Draining of the filter casing (9) is possible via the screw plug (235). For
these purposes, use collecting tank
For cleaning and for dissolving any encrustations, the filter can be put into an appro-
priate tank and placed into a cleansing agent, however, the container may be submerged
in the fluid only to the upper brim as otherwise, the dissolved dirt would get onto the
clean side.
Step E: After draining, blow filter off with compressed air from the clean side to the
dirty side (from the inside to the outside, not the other way round!).
Appropriate cleansing agents are benzene, benzine, Diesel fuel or a solvent-free cold
cleaner. Other special cleansing agents may be used with the concentration depending
on the kind and thickness of the dirt deposits to be removed. A soft brush may service
as a cleansing tool. Do not use sharp objects. In case of excessive contamination, it is
recommended to replace the filter (481) at certain intervals.
Step F: After cleaning the filter (481) is loosely mounted on the pipe (30) in the filter
casing bottom.
Step G: The (filter) casing cover (7) is fixed to the filter casing (9) again.
Note: The O-ring (119) must lie in its groove and not be damaged. Replace, if
necessary.
Step H: The (filter) casing cover (7) must be closed air tight, so that the pump may
not draw in any air.
Step I: The non-return valve (356) and the stop vale (355) are to be opened again.
Step J: In case of supply pressure, the filter casing (9) must be vented via the screw
plug (223) for re-starting the pump (please refer to section 9).
11 Troubles, causes and remedial action
The screw pumps operate without trouble, provided they are properly mounted and the
fluid to be pumped and the operating conditions correspond to the right values listed
under section 1.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-19 / 25
11.1 Troubles and causes
By means of the table below, the cause of troubles, if any, can be determined. In case
of troubles not listed herein or if they cannot be traced back to any of the causes listed,
it is recommend to check with Aalborg Industries.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-20 / 25 Language UK
Trouble and cause scheme
Trouble Cause Action nos.
Pump does not deliver Wrong sense of pump rotation
Pump without fluid to be handled
Stop valves closed
1
2
6
Pump is not vented No venting facility 7
Pump operates at minimum output Suction pipeline leaky
Filter clogged
3
12
Pump operates noisily Suction pipeline leaky
Geod. suction height to great
Air inclusions in the fluid pumped
Suction pipeline resistance to great
Filter clogged
3
4
8
5
12
Motor gets warm Power consumption of motor too great 9
Pump is seized Liquid level in tank too low
Viscosity too low, pressure too high
Filter clogged
10
11
12
Table 3
11.2 Measures to be taken for clearing the troubles
The table below shows a list of measures to be taken for clearing the troubles.
Measures scheme
Action nos. Measures
1 Change any two phases at the motor.
2 Fill pump with fluid to be handled.
3 Retighten flange joints, replace gaskets, if necessary.
4 Raise liquid level in tank. Lower pump.
5 Reduce suction pipeline resistance, e.g. by a greater pipeline cross-section and/or a design providing a more
favourable flow.
6 During operation, the stop valves / gate valves / non-return valves in the pipeline and at the reversing valve
casing must be completely open.
7 Mount vent valve in pressure pipeline.
8 Attend to better air separation in tank.
9 Check speed and power consumption of the motor. Compare voltage and frequency with the motor type plate.
10 Dismount pump and check for wear. Fill tank. Replace set of spindles and rotor housing. Replace other parts as
required.
11 Dismount pump and/or have pump overhauled at the works.
12 Clean and/or replace filter insert.
Table 4
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-21 / 25
12 Dismounting and mounting instructions
12.1 General
The most important dismounting and mounting operations are described in these in-
structions. The mounting steps described in the individual sections must be consistently
observed.
Item numbers mentioned in this section refer to the sectional drawings of the SPZ pump
in Figure 1 and Figure 2.
12.2 Dismounting of screw pump
Prior to commencing the dismounting, the following operations must be performed.
Step A: Close non-return valve and stop valve of the pump to be dismounted, and
switch over to the stand-by pump. With the stand-by pump, the operation
can be maintained without any troubles.
Step B: Pinch off power supply cable to the motor of the pump to be dismounted.
Motor must not be capable of being started.
Step C: Drain fluid to be pumped in flowable condition from the pump. For these
purposes, turn out screw plugs for draining.
Note: Use collecting tank.
Step D: Let screw pump cool down to ambient temperature.
Step E: Dismount manometer lines, manometer and holding device from the pump.
12.2.1 Dismounting of a screw pump from the twin aggregate
Step A: Loosen socket-head cap screws (215) at the pump bracket (460), and screw
out.
Step B: Loosen hexagon nuts (236) and (238) at the suction and pressure flange, and
unscrew.
Step C: Remove socket-head cap screws (206) and (208).
Step D: Withdraw pump from the centre bore of the pump bracket (460) and remove
from the reversing valve casing (301).
Step E: Remove gaskets (125) and (126), and clean sealing surfaces.
12.2.2 Dismounting of the shaft seal G 8.3
Step A: Withdraw coupling half from the driving spindle (12). Use detaching device.
Step B: Remove key (290) from the driving spindle (12).
Step C: Loosen socket-head cap screws (200) at the pump cover, drive side (3), and
screw out.
Step D: Dismount pump cover, drive side (3) with stationary seal ring (186) over the
driving spindle (12) from the pump casing (1).
Step E: Dismount circlip (250) from the pump cover, drive side (3).
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-22 / 25 Language UK
Step F: By means of an auxiliary tool, dismount stationary seal ring (186) and O-
ring from the pump cover, drive side (3).
Note: Particularly see to it that the stationary seal ring is pressed out concentri-
cally to avoid any damages.
Step G: Remove rotating part of the mechanical seal (186), consisting of rotating
seal ring, O- ring, and spring from the driving spindle (12).
12.2.3 Dismounting of the sliding bearing (bearing ring) with set of spindles
Step A: Dismount supporting washer (263) from the driving spindle (12).
Step B: Pull set of spindles with bearing ring (10) out of the pump casing insert (2).
Step C: Remove both idler spindles (13) from the driving spindle (12).
Step D: Remove bearing ring (10) from the driving spindle (12).
Step E: Loosen socket-head cap screws (201) at the pump cover, non-drive side (4)
and filter casing (9), and screw out.
Step F: Withdraw pump cover, non-drive side (4) and/or filter casing (9) from the
pump casing (1).
Step G: Remove gasket (100) and clean sealing surfaces.
Step H: Screw out socket-head cap screw (24) laterally at the pump casing (1).
Note: This socket-head cap screw serves to fix the pump casing insert (2) in the
pump casing (1).
Step I: By means of an appropriate tool, press pump casing insert (2) from the pump
non-drive side out of the pump casing (1). In case of pumps with filter,
previously remove pipe (29) from the pump casing (1).
12.3 Mounting of the screw pump
12.3.1 Mounting of the slide bearing (bearing ring) with set of spindles
Step A: Slightly oil the locating surfaces at the pump casing insert (2).
Step B: By means of an appropriate tool, press the pump casing insert (2) from the
drive side into the pump casing (1).
Note: The bore holes for the idler spindles must be arranged vertically and sym-
metrically in the pump casing. That means the location of the upper bore
must form a vertical axis with the suction and outlet branch in the pump
casing.
Step C: Via the lateral bore hole for the socket-head cap screw (24), pin pump casing
(1) together with the pump casing insert (2). Bore diameter: 4 mm. Bore
depth: 6 mm.
Step D: Screw socket-head cap screw (24) with sealing washer (151) laterally into
the pump casing (1), and tighten.
Step E: Push bearing ring (10) over the driving spindle (12) against the collar.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-23 / 25
Step F: Slightly oil driving spindle (12) and, together with the bearing ring (10),
press into the pump casing (1) from the drive side.
Note: The driving spindle is concentrically guided through the bearing ring in
the pump casing.
Step G: Insert new joint tape (165) between the bearing ring (10) and the pump casing
(1).
Note: Slight oiling facilitates mounting.
Step H: Turn both idler spindles (13) from the pump end side into the pump casing
insert (2).
Step I: In case of pumps with filter, install pipe (29) in the pump casing (1).
Step J: Place new gasket (100) onto the pump casing (1).
Step K: Fix the pump cover, non-drive side (4) and filter casing (9) with the socket-
head cap screws (201) to the pump casing (1).
Step L: Place supporting washer (263) in front of the collar of the driving spindle
(12).
12.3.2 Mounting of the shaft seal G 8.3
Note: Mechanical seals are high-quality precision parts. Careful handling and
extreme cleanliness during mounting are a condition of proper functioning.
To facilitate mounting, a suitable lubricant must be used (e.g. oil, no
grease).
Step A: Push rotating part of the mechanical seal (186) consisting of rotating seal
ring, O-ring and spring onto the driving spindle (12) in front of the support-
ing washer (263).
Step B: Press stationary seal ring (186) with new O-ring into the cleaned pump cover,
drive side (3). Apply appropriate auxiliary tool.
Note: In particular see to it that the rotating seal is concentrically pressed into
the delivery casing and not canted to avoid any damages.
Step C: Insert new O-ring (122) in front of the return bore hole into the pump casing
(1).
Step D: Fix pump cover, drive side (3) with new O-ring (120) and pressed-in sta-
tionary seal ring (186) with the socket-head cap screws (200) to the pump
casing (1).
Note: In doing so, the joint tape (165) is pressed into its end position.
Step E: Install circlip (250) in the pump cover, drive side (3).
Step F: Insert key (290) in the driving spindle (12).
Step G: Mount coupling half on the driving spindle (12). Use mounting device!
OIL PUMPS, TYPE SPZ OM9295_02#B.1
19-24 / 25 Language UK
12.3.3 Mounting of a screw pump into the twin aggregate
Step A: Place gasket (125) onto the pressure flange and gasket (126) onto the suction
flange.
Note: To facilitate mounting, we recommend to coat the gaskets with a suitable
adhesive.
Step B: Push pump into the centre bore of the pump bracket (460).
Step C: Fasten pump with the socket-head cap screws (206) and (208) and the hex-
agon nuts (236) and (238) to the reversing valve casing (301).
Step D: Fasten pump with the socket-head cap screws (215) to the pump bracket
(460).
Following the installation of the pump in the twin aggregate, the following operations
are to be performed:
Step E: Attach manometer lines, manometer and holding devices to the pump.
Step F: Connect power supply cable to the motor. See to sense of rotation.
Step G: Prior to re-starting, fill pump with the fluid to be handled.
13 Replacement/spare parts
Parts marked (2) and/or (3) in the parts list, see Figure 1 and Figure 2can be provided
as replacement/spare parts.
Driving spindle (12) and idler spindles (13) are available only as complete sets of
spindles for replacement.
OIL PUMPS, TYPE SPZ OM9295_02#B.1
Language UK 19-25 / 25
Table of contents
Operation and maintenance
Description Document ID Page
.
Handling fuel oil........................................................ OM9280_02.............. 20-2
Gauge board............................................................. SD9240_14............... 20-4
Burner sequence diagram............................................ OM5560_94.............. 20-5
Electric pre-heater..................................................... OM5560_88.............. 20-11
Oil/air regulation....................................................... OM5560_95.............. 20-13
Ignition electrodes..................................................... OM5560_84.............. 20-17
Combustion head....................................................... OM5560_87.............. 20-18
Photo cell................................................................. OM8630_01.............. 20-21
Nozzle selection........................................................ OM5560_38.............. 20-22
Nozzles.................................................................... OM5560_37.............. 20-27
Viscosity - temperature chart....................................... OM9280_01.............. 20-28
Oil System................................................................ OM5560_96.............. 20-30
Burner operation........................................................ OM5560_98.............. 20-31
Operating instructions................................................ OM5560_99.............. 20-34
Emergency operation................................................. OM5560_75.............. 20-38
Commissioning......................................................... OM5560_97.............. 20-40
Maintenance............................................................. OM5560_85.............. 20-50
Faults and rectifying faults.......................................... OM5560_92.............. 20-52
TABLE OF CONTENTS
Language UK 20-1 / 54
Handling fuel oil
1 Precautions to be taken with fuel oil
Marine gas oil MGO and marine diesel oil MDO are distillates of crude oil. Heavy fuel
HFO is the residual of the crude oil after the removal of distillates.
Liquid oil is very difficult to ignite in bulk and not capable of spontaneous combustion.
However both the distillates and the residuals are capable of forming vapours which
are explosive when mixed with air. As the vapours can be heavier that air, it tends to
accumulate in low levels such as bilges and bottoms of tanks where it may remain
undiscovered until ignited by a naked light or spark. It is always present in a partly
filled oil tank or in a tank which has contained fuel oil and is given off through the
vents from tanks in the process of being filled.
If allowed to continue, a leak in any part of the oil burning system may result in an
accumulation of this explosive vapour.
Ignition of the vapour can be caused by an open light, electric spark, smoking, spark
caused by striking metal, heat from the filament of a broken electric lamp, sparks from
funnel or can be communicated from galley or fires under boilers.
Note: An oil fire cannot be extinguished by water, but may be extinguished by
sand, steam or chemical fire extinguishers.
An intelligent appreciation of the properties of fuel oil as described above is a better
prevention of accident than adherence to any set of rules that may be pre-described.
HANDLING FUEL OIL OM9280_02#D.1
20-2 / 54 Language UK
However, the following detailed precautions should be rigidly enforced:

When oil is being received, no naked light or electric apparatus liable to spark
should be permitted within 20 meters of the oil hose, tank or compartment, con-
taining the tank or the vent from the tank, except when special arrangements are
carried out.

While receiving fuel oil, the storage tank must be closely watched for leaks, and
care must be taken that all outlets from the tank, except the vents, are closed.

No naked lights or electric apparatus liable to spark should be permitted at any

time in a compartment containing a fuel oil tank. Electric lamps used in such com-
partments should have a wire protector around the bulb or be of a type that will
ensure the breaking of a circuit through the lamp in the event of the lamp being
broken.

No one should be allowed to enter a fuel oil tank until it has been gas-freed, and
any person then entering the tank must have a properly tended life-line around his
body in order to be hauled out if overcome by gas.

Electric fuses and switches, unless the enclosed type, should not be permitted in
compartments containing fuel oil pumps or piping.

Care must be taken that the wire-gauze protectors in vent pipes from fuel oil tanks
are intact at all times.

Dampers, where fitted in the uptakes of the boilers, must be kept fully open while
burning oil. Otherwise, this may result in dangerous accumulation of gas in the
furnace with a resultant blowing out into the boiler or engine room.

The valves on glass gauges in fuel oil storage or settling tanks should be kept
habitually shut. When a reading of the gauge is desired, the valves may be opened,
but must be shut again at once.

In each boiler or engine room fitted for oil burning there should be fire extin-
guishing apparatus in accordance with the requirements/rules from the authorities
and classification societies in question such as, e.g.: Fire hose, permanently cou-
pled and of sufficient length to reach all parts of the boiler or engine room, and
either:
- (a) a box containing at least 85 litres (2 cubic ft) of dry sand with a large scoop
- (b) a chemical fire extinguisher of the tank type

When the fuel oil system has not been in use for a long period, or after joints in
the piping have been re-made, the system should be tested cold under a pressure
at least equal to the working pressure before fires are ignited. During the test a
careful inspection for leaks should be carried out.

Fuel oil should not be habitually heated above 60C for marine gas oil / diesel oil
and 120C for heavy oils and never above its flash point in any part of the system
except in the burners.

Care must be taken to prevent accumulation of oil or vapour in any place outside
the system and in ships particularly in bilges under the furnace. This can be ac-
complished by rigid cleanliness.
HANDLING FUEL OIL OM9280_02#D.1
Language UK 20-3 / 54
Gauge board
1 Description
The function of the gauge board is to control the burner and to give alarm and shut
down for low and high steam pressure.

A pressure gauge is fitted for analogous reading of the actual steam pressure in the
boiler.

A pressure switch "high steam pressure" gives shut down and burner cut-off when
the steam pressure rises above the pre-adjusted set point. The pressure switch locks
the burner in stop mode. Operation of the burner is only possible when the steam
pressure falls below the differential set point of the pressure switch and the shut
down function is reset.

A pressure transmitter connected directly on the boiler converts the actual steam
pressure of the boiler into corresponding electric signals. The signals are used to
give alarms for low/high steam pressure and shut down/burner cut-off for high
steam pressure. The signals also control start/stop and modulation set point of the
burner. Furthermore, the pressure transmitter can be used for remote steam pres-
sure indication.
GAUGE BOARD SD9240_14#A.2
20-4 / 54 Language UK
Burner sequence diagram
1 General
The following section describes the burner firing sequence for KBO-E modulating
pressure atomising burners. Figure 1 shows a guide to the diagrams, and Figure 2 to
Figure 5 show the burner firing sequence.
The burner firing sequence, e.g. start, purge, ignition, etc., is handled by the control
system. The sequence is divided into a number of steps, which are executed one by
one. When a specified step is active, the control system activates a number of output
signals and timers. In this way the necessary execution and surveillance of these actions
can be performed. On the control panel the actual sequence step will be indicated.
The burner firing sequence consists of 13 steps. The steps 0-8 handle the burner start
sequence, and the steps 10-13 concern the burner stop sequence. In the normal oper-
ation of the burner, step 8 (mod free) will be active. In this step the burner operates in
modulation free mode, and the load is controlled by the steam pressure regulation
output. If the steam pressure rises above the set point for stop of the burner, the control
system initiates the burner stop sequence. When the stop sequence is completed, the
burner will be in step 0 (ready). If the steam pressure falls below the set point for start
of the burner, a new start-up sequence will be initiated.
In addition to these steps, the sequence is provided with a stop step and a shutdown
step. The stop step must be selected on the control panel. In this step the burner remains
stopped regardless of the steam pressure. The shutdown step is active if one or more
safety interlock shut downs are present. If a safety interlock shut down arises in any
one of the sequence steps, the burner firing sequence is immediately interrupted. When
the safety interlock circuit is restored, and the shut down is reset, the sequence returns
to step 0 (ready).
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 20-5 / 54
Diagram
STEP No.
Sequence
STEP No.
Sequence
(continued)
Guide to diagram
Conditions which must be fulfilled before leaving the above
step and entering the next step
When entering a sequence step, the associated outputs
will be active, and the described actions will be executed
Shut-down of the burner
due to one or more active
safety interlocks. The
sequence will return to
step shut-down
Normal stop
of the burner
Continuance of sequence step
Figure 1 om5560_94_seqguix0055840en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
20-6 / 54 Language UK
Sequence diagram
STEP
Shut-down
Power on
One or more safety interlocks active
Deactivate start request to PMS
Stop ignition (switch off power to ignition transformer)
Deactivate oil valves
Close oil safety valves 1 + 2
Deactivate start signal to burner motor
Set servo motors to closed position
Set all timers to zero, except timers for water level alarms/
shut downs
Safety interlocks OK. When all shut downs can be and are
reset change to step 0 (ready)
Set servo motors to closed position
Stop burner motor
In automatic mode change step if boiler pressure is
lower than set point chosen + master start difference
In manual mode change step if soft key for start is
activated
Send start request to PMS system, if this possibility is
provided in the control system
Start timer for PMS feedback signal
Start permission from PMS system given
STEP
Stopped
To enter this step it must be chosen on the control panel
Set all timers to zero
Set burner to stop mode
When the step is changed to step 0 (ready) on the control
panel, the burner stop mode is canceled
STEP 0
Ready
STEP 1
Starting
STEP 1
Starting
(continued)
Start burner motor
Reset timer for PMS feedback
Start timer for maximum start sequence time
Start timer for burner motor start
Burner firing sequence
Continued in next figure
Shut-down Stop
Stay in step stopped
Shut-down
Stay in shut-down step if
safety interlocks are not OK
Stop
Stay in step 0 (ready)
Shut-down
Shut-down Stop
Change to step 0 (ready)
Stop
Change to step 0 (ready)
Reset timer for maximum
start sequence time
Shut-down
Feedback signal for burner motor running
Figure 2 om5560_94_seqrmsx0055850en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 20-7 / 54
Sequence diagram, continued
STEP 2
Purge
Set servo motors to purge position
Start timer for servo motors in position
Feedback signal for servo motors in position
If servo motors position are OK during purge period, change
step
If servo motors position are not OK, return to step 2 again
Set servo motors to ignition position
Start timer for servo motor in position
Start timer for oil heating
Feedback signal for servo motors in position
Continue when timer periods for oil heating have expired
Start ignition (energize ignition transformer)
Open oil safety valves 1 + 2
Start timer for ignition
Start timer for purge
STEP 3
Ignition
position
STEP 4
Ignition
Burner firing sequence continued from previous figure
Continued in next figure
Shut-down Stop
Change to step 0 (ready)
Reset timers for maximum
start sequence time and
purge time
Stop
Stop burner motor
Change to step 0 (ready)
Reset timers for maximum
start sequence time and
ignition position and
oil heating
Shut-down
Shut-down Stop
Stop ignition, close oil
safety valves 1 + 2
Reset timer for maximum
start sequence time
Change to step 0 (ready)
STEP 2
Purge
(continued)
Shut-down Stop
Change to step 0 (ready)
Reset timer for maximum
start sequence time
Change step when timer period for ignition has expired
STEP 5
Safety time
Activate oil valves
Start timer for safety time
Continue when timer period for safety time has expired
Stop
Stop ignition
Reset timer for maximum
start sequence time
Change to step 10
(steam purge position)
Shut-down
Figure 3 om5560_94_seqrmsx0055860en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
20-8 / 54 Language UK
Sequence diagram, continued
Activate flame surveillance
Reset timer for maximum start sequence time
Burner firing sequence continued from previous figure
Shut-down Stop
Change to step 10
(steam purge position)
STEP 6
Flame
stable
Shut-down Stop
Stop ignition
stop sequence initiates
Change to step 10
(steam purge position)
STEP 5
Safety time
(continued)
Start timer for flame stable
Stop ignition (switch off ignition transformer)
Change step when timer period for flame stable has expired
STEP 8
Rising/
mod. free
(continued)
Modulating operation of the burner according to the signals
from the steam pressure transmitter
In automatic mode change step if boiler pressure is
higher than set point chosen + stop differential set point
In manual mode change step if soft key for stop is activated
Shut-down Stop
Change to step 10
(Steam purge position)
STEP 11
Steam
purge 1
Shut-down
Deactivate oil valves
Close oil safety valves 1 + 2
Deactivate flame surveillance
Continued in next figure
STEP 13
Postpurge
Set servo motors to purge position
Start timer for servo motors in position
Feedback signal for servo motors in position
Shut-down
Figure 4 om5560_94_seqrmsx0055870en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 20-9 / 54
Sequence diagram, continued
Start timer for postpurge. If timer is set to 0 sec. the
furnace will not be purged.
Change to step 0 (ready) when timer period for postpurge
has expired
Burner firing sequence continued from previous figure
STEP 0
Ready
Shut-down
STEP 13
Postpurge
(continued)
Figure 5 om5560_94_seqrmsx0055880en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
20-10 / 54 Language UK
Electric pre-heater
1 Pre-heater
The electric oil pre-heater, illustrated in Figure 1, is placed on the burner housing and
is used for preheating the fuel oil. The pre-heater is provided with electric heating
elements, which conduct the produced heat to the heavy fuel oil. Depending on the oil
throughput and viscosity the burner can be equipped with one or more pre-heaters.
Irrespective of the number of pre-heaters there is only one common temperature con-
troller. However, each pre-heater is provided with its own limit thermostat.
Illustration of the electric oil pre-heater
1 Pre-heater
2 Temperature sensor for limit thermostat
3 PT100 sensors
4 Controller wiring
5 Remote indication wiring
6 Limit thermostat
Figure 1 om5560_88_oilburx0055800en.wmf
1.1 Temperature limit thermostat
The temperature limit thermostat (6) has a fixed temperature limit of 180C and it is
fitted with a reset button. If the oil temperature becomes too high, the temperature limit
thermostat stops the burner. The shut down is indicated in the control system. In case
of failure, the fault has to be repaired. Before the pre-heater can be taken into service
again, the reset button on the temperature limit thermostat must be activated and the
shut down in the control system must be reset.
Note: Reset must be carried out when the thermostat is not under voltage.
ELECTRIC PRE-HEATER OM5560_88#A.2
Language UK 20-11 / 54
1.2 Temperature controller for pre-heater
The desired fuel oil temperature can be set in the control system together with alarm
set points and shut down set points. The fuel oil temperature in the pre-heater is reg-
istered by a Pt 100 resistance temperature sensor and supplied to the control sys-
tem.Fluctuations in oil temperature are minimized by the Pt 100 sensor which is placed
directly on the heating plate.If the oil temperature becomes too low or too high during
operation, e.g. if the heater elements are faulty, the control system stops the burner and
actuates a shut down indication.
Furthermore, the pre-heater is equipped with an additional Pt 100 resistance temper-
ature sensor with transmitter, which handles remote indication of the oil temperature.
1.3 Test of the functions
The function of the temperature limit thermostat can be tested by dismantling one of
the wires at the terminals to the temperature limit thermostat. The burner stops imme-
diately.
The low oil temperature shut down can be tested by disconnecting the electric power
to the pre-heater. When the oil temperature drops below the shut down limit the burner
stops.
ELECTRIC PRE-HEATER OM5560_88#A.2
20-12 / 54 Language UK
Oil/air regulation
1 Oil/air regulator
The oil and air regulation for the burner are handled by two servomotors. The oil flow
is regulated bya valve, which is regulated by a servomotor. The air damper is regulated
by a second servomotor.Figure 1 illustrates the regulator system.
The servomotorsare controlled by the control system during start-up/stop and operation
of the burner.
Illustration of the regulator system
1 Air damper
2 Servomotor
3 Oil regulator
4 Dosing nozzle
5 Dosing shaft
6 Servomotor
A Oil inlet
B Oil return
C Air
Figure 1 om5560_95_oilburx0055900en.wmf
The oil quantity burned is determined by nozzle size and oil pump pressure. The oil
regulator regulates the return oil flow according to the capacity demand. At partial load
the oil regulator is open so that the oil throughput in the valve is at maximum and the
return oil flow pressure at minimum. At full load the oil regulator is closed whereupon
the oil throughput is at minimum and the pressure at maximum.
OIL/AIR REGULATION OM5560_95#A.2
Language UK 20-13 / 54
The air quantity is matched to the fired oil quantity by means of the control system,
which controls the servomotor for the air dampers.
2 Servomotor
The servomotorswhich operate the oil regulator and air dampers are equipped with a
number of cam switches and a potentiometer. The outer scale on the camshaft serves
as a position indicator. Figure 2 shows an illustration of the servomotor.
Illustration of the servomotor
1
S1 S2
2 3
N
M
R1
fail-safe
4 5 6
L D1
I II
I Right-handed operation
II Left-handed operation
Figure 2 om5560_95_oilburx0055890en.wmf
In automatic operation of the burner, signals are sent from the control system to the
servomotor for positioning the air dampers dependent on the sequence step for the
burner. The potentiometer provides feedback signals to the control system when the
burner operates in this mode.
In emergency operation of the burner, the servomotor is operated by pressing the in-
crease and decrease buttons located inside the boiler control panel.
Cam switches No. 1 and No. 2, which are the switches for purge/full load position and
closed position respectively, are active in automatic operation mode. Therefore, the
servomotor cannot open or close the air dampers beyond the setting of the switches
regardless of the signals sent from the control system. By this, an extra control of the
combustion process is added to the burner operation. Please note that cam switch No.
1 is also active in emergency operation mode.
2.1 Calibration of the servomotor range
During commissioning, the servomotor range must be calibrated. The low and high
range should be set to 0 and 90 opening of the air dampers respectively.
OIL/AIR REGULATION OM5560_95#A.2
20-14 / 54 Language UK
The output signal from the potentiometer is a voltage signal, which is converted into
a resistance signal in the control system. On the local panel the resistance signal is
displayed in the menu setup/calibrate/servo motor/raw data. When the position of the
servomotor is set to 0, which can be seen on the outer scale, the raw data line displays
a numerical value. This value must be entered in low range menu line.
After calibration of the low range position, the servomotor should be set to 90. The
new numerical value, which is displayed in the raw data line, should be entered as the
high range. In this way the operation range of the servomotor is calibrated for an op-
erating range between 0 and 90 corresponding to 0-100%.
The position of the servomotor will be handled and displayed as a percentage value in
all other menus.
Furthermore, the time to operate the servomotor from 0 to 90 and the accepted re-
sponse threshold can be set on the local control panel.
2.2 Pre-adjustment of the servomotor settings
The following servomotor positions for operation should be set as preliminary settings
on the local control panel in the menu setup/settings:

Stand-by position (burner stopped) 0% (0)

Ignition position 22% (20)

Minimum firing position 33% (30)

Purge and full load position 67% (60)

Please consider the proposed settings as guidelines only as the final settings should be
performed after measuring the flue gas (CO2/O2 content).
3 Oil regulator
The oil regulator is driven by the servomotor in a continuous movement from partial
load to full load, thus regulating the return oil flow from the nozzle head. Figure 3
illustrates the oil regulator. It is provided with indicator and scale.

Indicator in position 1: dosing shaft open. The return flow is at maximum and the
return pressure at minimum.

Indicator in position 13: dosing shaft closed. The return flow is at minimum and
the return pressure at maximum.
There is a number on the dosing shaft and on the indicator which shows the size of the
groove on the shaft.
OIL/AIR REGULATION OM5560_95#A.2
Language UK 20-15 / 54
Illustration of the oil regulator
1 Body
2 Dosing shaft
3 Dosing nozzle
4 Nipple
5 Compression spring
6 Thrust washer
7 Roller bearing
8 Spring cotter
9 End flange
10 Hexagonal socket screw
11 Coupling
12 O-ring
13 X-ring
14 O-ring
15 Needle valve
16 Needle valve
17 Retaining ring
18 Retaining ring
19 Non-return valve
20 Coupling
21 Washer
22 Indicator
23 Scale
B Oil to valve
C Oil from valve
Figure 3 om5560_95_oilburx0055910en.wmf
OIL/AIR REGULATION OM5560_95#A.2
20-16 / 54 Language UK
Ignition electrodes
1 Setting of the ignition electrodes
The ignition electrodes for the burner are shown in Figure 1 together with the adjust-
ment dimensions. As the conditions may vary from boiler to boiler, the indicated di-
mensions should only be considered as guidelines. If ignition problems emerge, a more
favourable adjustment of the electrodes, suitable for the present conditions, must be
found by experiments.
Illustration of the ignition electrode settings
Burner type
KBO-R13M
KBO-R14M
KBO-R15M
KBO-R25M
KBO-R30M
KBO-R40M
KBO-R50M
H
17
17
17
17
9
9
9
K
3.5
3.5
3.5
3.5
3
3
3
L
6
6
6
6
10
10
10
Figure 1 om5560_84_oilburx0055750en.wmf
When the ignition electrodes are adjusted, the following must be observed:

The distance of the ignition electrodes to the nozzle and diffuser should be checked.

The atomising oil spray must never touch the ignition electrodes.

The distance of the ignition electrodes to the diffuser and the nozzle must always
be lager than the distance of the spark gap.

If a nozzle with a larger spray angle is fitted, the electrodes must be adjusted back-
wards, or perhaps be adjusted slightly upwards.
IGNITION ELECTRODES OM5560_84#A.2
Language UK 20-17 / 54
Combustion head
1 Adjustment ofthe combustion head
The oil burner is delivered with a combustion head and an air diffuser disc that suit the
specified boiler type and oil quantity in the best way.Figure 1 illustrates the combustion
head for KBO-R13/14M burners,Figure 2 for a KBO-R15M burner, and finally Fig-
ure 3 for KBO-R20/60M burners.
To obtain the best possible combustion performance the combustion head should be
adjusted to fit the actual boiler furnace. The combustion quality can be checked by
means of flue gas analysis.The air velocity in the combustion head can be adjusted by
loosening the fixing screwin the adjustment ring and moving the ring (4) in the direction
of the flame tube (6) to change the distance between the adjustment ring and the edge
of the diffuser disc (5). On low capacity the adjustment ring is advanced and on high
capacity retracted. If the adjustment ring is set too far forward, the combustion air
velocity in the combustion head is too high, the ignition is more difficult or there is
not enough air to support the combustion (high CO content). If the adjustment ring is
too far back, the combustion air velocity is too low and the combustion characteristics
become worse (O2 content is too high).
Combustion head for KBO-R13/14M burners
1 Burner housing
2 Fixing screw for combustion head
3 Combustion head guide
4 Adjustment ring
5 Diffuser disc
6 Flame tube
7 Oil nozzle
9 Fixing nut for diffuser disc
10 Fixing screw for combustion head guide
8 mm
Figure 1 om5560_87_oilburx0055780en.wmf
COMBUSTION HEAD OM5560_87#A.2
20-18 / 54 Language UK
Combustion head for a KBO-R15M burner
1 Burner housing
2 Fixing screw for combustion head
3 Combustion head guide
4 Adjustment ring
5 Diffuser disc
6 Flame tube
7 Oil nozzle
9 Fixing nut for diffuser disc
10 Fixing screw for combustion head guide
8 mm
Figure 2 om5560_87_oilburx0055780en.wmf
Combustion head for a KBO-R20/60M burners
8 mm
3 Combustion head
4 Adjustment ring
5 Diffuser disc
7 Oil nozzle
Figure 3 om5560_87_oilburx0055790en.wmf
COMBUSTION HEAD OM5560_87#A.2
Language UK 20-19 / 54
Note: If the position of the adjustment ring has to be altered in relation to the
diffuser disc, the air velocity and quantity in the combustion head will
change. Check the combustion values by means of flue gas analysis and, if
necessary, adjust the combustion air quantity to be adequate.
1.1 Dismounting the combustion head
If the combustion head has to be dismounted, e.g. due to cleaning, the following work
steps must be carried out:
Dismounting the combustion head for KBO-R13/14M burners
Step A: Ensure that the burner is stopped.
Step B: Close the quick-closing valves and swing out the burner.
Step C: Unscrew the fixing screws for the combustion head, see Figure 1.
Step D: Withdraw the combustion head. The flame tube is fixed with cotters to the
combustion head guide.
Step E: Reassemble in reverse order.
Dismounting the combustion head for a KBO-R15M burner
Step A: Ensure that the burner is stopped.
Step B: Close the quick-closing valves and swing out the burner.
Step C: Unscrew the fixing screws for the combustion head guide and adjustment
ring, see Figure 2.
Step D: Withdraw the adjustment ring from the combustion head.
Step E: Unscrew the fixing nuts for the diffuser disc.
Step F: Withdraw the diffuser disc from the combustion head.
Step G: Withdraw the combustion head guide with flame tube out of its place from
the combustion chamber side. The flame tube is fixed with cotters to the
combustion head guide.
Step H: Reassemble in reverse order.
COMBUSTION HEAD OM5560_87#A.2
20-20 / 54 Language UK
Photo cell
1 Description
The RAR detector is used for supervision of yellow burning oil flames. If the photo
cell detects a missing flame, the burner stops instantaneously. It is not possible to start
the burner before the control system has been reset.
With this type of detector, the radiation of the oil flame in the visible band of the light
spectrum is used to generate a flame signal. The light-sensitive element is a photo cell.
When illuminated, it generates DC voltage which causes a current to flow to the input
of the flame signal amplifier in the control unit. Hence, the photo cell is an active
detector.
The cell is insensitive to infrared radiation. If the burner is started with an illuminated
combustion chamber, the start sequence of the burner breaks, and an alarm for flame
failure will be indicated.
The number of photo cells for automatic operation and emergency operation depend
on the classification society.
1.1 Commissioning
The intensity of the light radiation can be checked by measuring the detector current
by means of a DC ampere meter (internal resistance 5000 ohm). Figure 1 shows the
measuring circuit.
Note: If the wiring of the photo cell is connected incorrectly, it is not possible to
start the oil burner.
Measuring circuit
13
10
24
24
LAE1...
LAE10...
LOK16...
LAL2.../LAL3...
14
9
22
22
RAR
A
M
-
-
-
+
+
Figure 1 photcircax0460930en.wmf
PHOTO CELL OM8630_01#C.1
Language UK 20-21 / 54
Nozzle selection
1 Description
The selection of a nozzle to a modulating oil burner can be done on basis of Table 1
and two calculations. The table shows the nozzle number and oil throughput for max.
and min. load at a specified reference pressure. The supply pressure should be between
25 - 30 bar when running on both DO and HFO. If the burner only operates on DO,
the supply pressure can be between 20 - 30 bar.
The nozzle is a spill return type nozzle 12-W2 with a spray angle of 60. The regulating
range for this type of nozzle is between 25 - 100% of the total oil throughput.
Note: Ensure that the supply pressure does not fall below the above mentioned
settings. The burner can only operate if the pressure is sufficiently high in
order to withdraw the spring inside the nozzle head.
1.1 Selecting a nozzle size
When a nozzle is selected the required oil throughput must be known. The selection
should be made with regard to the above mentioned supply pressure settings.
If the gap between two nozzles sizes results in a lower supply pressure than required,
the pressure must be increased to minimum 25 bar for HFO and 20 bar for DO. The
higher oil throughput caused by an increase of the supply pressure can be reduced by
limiting the oil regulator movement. This is done by adjusting the full load limit switch
in the servomotor to an appropriate lower position. The range of regulation is reduced
by this action.
1.2 Nozzle size selection
Determining the nozzle size and supply pressure can be done either by using the charts
in Figure 1 or by using Table 1 and the following formulas.
NOZZLE SELECTION OM5560_38#G.1
20-22 / 54 Language UK
Nozzle size
W2 Nozzle capacity W2 Nozzle capacity
O
u
t
p
u
t

H
F
O

k
g
/
h
O
u
t
p
u
t

H
F
O

k
g
/
h
Atomizing pressure bar Atomizing pressure bar
340
W2-275
W2-700
W2-650
W2-600
W2-550
W2-500
W2-450
W2-400
W2-360
W2-330
W2-300
W2-250
W2-225
W2-200
W2-180
W2-160
W2-145
W2-130
W2-115
W2-100
W2-90
W2-80
320
300
280
260
240
220
200
180
160
140
120
100
80
25 26 27 28 29 30 25 26 27 28 29 30
880
860
840
820
800
780
760
740
720
700
680
660
640
620
600
580
560
540
520
500
480
460
440
420
400
380
360
340
320
Figure 1 om5560_38_noz_cax0055520en..wmf
Figure 1 is only applicable, when the viscosity is 15 cSt.
The nozzle size and supply pressure can be determined by means of the following
equations provided the required oil throughput and the medium viscosity are known:
- mref: reference mass flow (nozzle number) [kg/h]
- m: required oil mass flow [kg/h]
- : kinematic viscosity [cSt]
- ref: kinematic viscosity, reference (5) [cSt]
- P: Supply pressure [bar]
- Pref: Reference pressure (25)[bar]
Calculation of nozzle size and supply pressure is carried out by the following steps:
NOZZLE SELECTION OM5560_38#G.1
Language UK 20-23 / 54
Determine the nozzle size by assuming a supply pressure at 27 bar.
Select from the left column in Table 1 the nozzle number, which is closest to the
calculated nozzle size.
Determine the actual supply pressure.
Note: If the calculated supply pressure is not within the required limits select
another nozzle size and re-calculated. If the result is still not acceptable,
consider the actions described in section 1.1.
1.3 Example
Known:
Required oil throughput: 260 kg/h HFO, viscosity 14 cSt.
Required:
The nozzle size and actual supply pressure
1.3.1 Using the chart
When looking at the left part of Figure 2, finding 260 kg/h HFO on the vertical axis,
gives nozzle number: W2-225 and a supply pressure at app. 28 bar.
NOZZLE SELECTION OM5560_38#G.1
20-24 / 54 Language UK
Nozzle size example
W2 Nozzle capacity W2 Nozzle capacity
O
u
t
p
u
t

H
F
O

k
g
/
h
O
u
t
p
u
t

H
F
O

k
g
/
h
Atomizing pressure bar Atomizing pressure bar
340
W2-275
W2-700
W2-650
W2-600
W2-550
W2-500
W2-450
W2-400
W2-360
W2-330
W2-300
W2-250
W2-225
W2-200
W2-180
W2-160
W2-145
W2-130
W2-115
W2-100
W2-90
W2-80
320
300
280
260
240
220
200
180
160
140
120
100
80
25 26 27 28 29 30 25 26 27 28 29 30
880
860
840
820
800
780
760
740
720
700
680
660
640
620
600
580
560
540
520
500
480
460
440
420
400
380
360
340
320
Figure 2 om5560_38_moz_cax0055510en..wmf
1.3.2 Using the formulas
Calculations:
Determine nozzle size:
Select nozzle size:
Nozzle No selected: 225
NOZZLE SELECTION OM5560_38#G.1
Language UK 20-25 / 54
Determine actual supply pressure:
1.4 Nozzle selection chart
Nozzle selection table
Nozzle No. Max. oil throughput [kg/h] at an oil
pump pressure of 25 bar and a viscos-
ity at 5 cSt, when the return line is
closed.
Min. oil throughput [kg/h] at an oil pump
pressure of 25 bar and a viscosity at 5 cSt,
when the return line pressure is 7 10 bar.
12-W2-40-60 40 10
12-W2-50-60 50 12
12-W2-60-60 60 15
12-W2-70-60 70 18
12-W2-80-60 80 20
12-W2-90-60 90 22
12-W2-100-60 100 25
12-W2-112-60 112 28
12-W2-125-60 125 31
12-W2-140-60 140 35
12-W2-160-60 160 40
12-W2-180-60 180 45
12-W2-200-60 200 50
12-W2-225-60 225 56
12-W2-250-60 250 62
12-W2-275-60 275 68
12-W2-300-60 300 75
12-W2-330-60 330 82
12-W2-360-60 360 90
12-W2-400-60 400 100
12-W2-450-60 450 112
12-W2-500-60 500 125
12-W2-550-60 550 138
12-W2-600-60 600 150
12-W2-650-60 650 162
12-W2-700-60 700 175
Table 1
NOZZLE SELECTION OM5560_38#G.1
20-26 / 54 Language UK
Nozzles
1 Fitting and removal of nozzles
A nozzle can be replaced without affecting the function of the hydraulic nozzle shut-
off valves.
Inspection and change of the nozzles are easily done as the burner is constructed with
a swing flange.
Exchanging of an oil nozzle:

Unscrew the lock-nut, and the casing can be swung out

For mounting/dismounting use a spanner and keep the nozzle head fixed by means
of another spanner

After replacing the nozzle ensure that it is tight

To prevent entry of air into the oil system it is advisable to close the stop valves in the
suction intake and return line during exchange of the nozzle.
As a general rule a nozzle should always be exchanged if it is dirty or worn out. A good
burner performance can only be guaranteed with a new and/or a clean nozzle.
The nozzles should only be cleaned due to a shortage of nozzles.
The nozzles should be dismantled into individual parts and washed in a suitable fluid
such as benzine or petrol. If available, compressed air is the most suitable cleaning
medium.
Note: Solid objects such as steel needles are completely unusable, and they are
under NO circumstances to be used as cleaning tools.
Note: Nozzles cannot be returned for credit or exchange.
When extra oil nozzles are ordered please state the through-put in US Gal/h and the
spray angle.
NOZZLES OM5560_37#A.2
Language UK 20-27 / 54
Viscosity - temperature chart
1 Description
The preheating temperature can be determined by means of the viscosity - temperature
chart shown in Figure 1. In order to use the chart, the viscosity of the fuel oil must be
known at a reference temperature.
It should be noted that the preheating temperature should be set somewhat higher than
the temperature shown in the chart due to the heat loss between pre-heater and nozzle/
cup.
1.1 Example
The example is based on a pressure jet burner type MS or RMS.
Known:
Oil viscosity: 380 cSt. at 50C
Required:
Preheating temperature in C
Procedure to be followed:
Step A: Follow the reference temperature line at 50C vertically down to the inter-
section with the 380 cSt. viscosity line.
Step B: From this point move parallel down with the nearest fuel grade line.
Step C: When the line meets the recommended nozzle viscosity line, go vertically
up to the temperature axis.
Step D: At this point read the desired preheating temperature of 150C.
VISCOSITY - TEMPERATURE CHART OM9280_01#A.2
20-28 / 54 Language UK
Viscosity - temperature chart
10,000 10,000
9,000 9,000
8,000 8,000
7,000 7,000
6,000 6,000
5,000 5,000
4,500 4,500
4,000 4,000
3,500 3,500
3,000 3,000
2,500 2,500
2,000 2,000
1,500 1,500
1,000 1,000
900 900
800 800
700 700
600 600
500 500
450 450
400 400
350 350
300 300
250 250
200 200
150 150
100 100
80 80
70 70
60 60
50 50
45 45
40 40
35 35
30 30
25 25
20 20
15 15
10 10
90 90
9 9
8 8
7 7
6 6
5 5
4 4
3 3
2 2
1 1
-15 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
28.5
40
50
60
70
80
90
100
150
200
300
400
500
600
800
1,000
1,500
2,000
3,000
4,000
5,000
8,000
10,000
15,000
20,000
30,000
40,000
K
I
N
E
M
A
T
I
C
,

C
E
N
T
I
S
T
O
K
E
S
R
E
D
W
O
O
D
,

1

S
E
C
O
N
D
K
I
N
E
M
A
T
I
C
,

C
E
N
T
I
S
T
O
K
E
S
TEMPERATURE
TEMPERATURE
R
e
d
w
o
o
d
1

s
e
c
.
c
S
t
.
o
Centigrade
c
S
t
.
20 40
o
Fahrenheit
5 10 30 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350
o
C
o
F
1
2
3
1
2
3 Recommended nozzle viscosity for pressure atomising burners type MS, RMS and KBP
Recommended nozzle viscosity for steam atomising burners
Recommended cup viscosity for rotary cup burners
Viscosity - temperature chart
4 Recommended nozzle viscosity for pressure atomising burners type KBO
4
Figure 1 om9280_01_visc1x0060120en.wmf
VISCOSITY - TEMPERATURE CHART OM9280_01#A.2
Language UK 20-29 / 54
Oil System
1 Fuel oil system
This section describes the oil system in general terms together with some of the re-
quirements needed to have a safe and reliable burner operation. The flow diagram of
the oil system is shown in another chapter.
The oil system is fitted with one set of supply oil pumps common for both DO and
HFO. The fuel type is selected by manually operating a three-way valve in the oil
system.
The oil system consists of oil tanks for DO and HFO, mixing tube, oil pumps and
pressure regulating valve, and a pre-heater at the burner unit.An orifice is fitted at the
pre-heater in order to limit return flow through the pre-heater, when the burner is stop-
ped.
The heavy fuel oil tank may be provided with a heating coil for heating up the fuel oil
in the tank to a viscosity between 60 cSt and 380 cSt.
Whenever a boiler plant is intended to operate on heavy fuel oil, all pipes carrying fuel
oil must be insulated and traced in order to keep a sufficiently low viscosity of the oil.
The tracing can be done either by means of steam heating or by means of electric
heating cables. The tracing is to be controlled.
The pumping capacities for the pumps must be calculated in such a way that there will
be sufficient oil flow to the burner, and the pressure regulating valve in full load con-
dition.
In general it is recommended that the pipe lines to and from the fuel oil supply pumps
are dimensioned so that the velocities inside the suction and return pipes do not exceed
0.5 m/s and so that the velocity inside the pressure pipe does not exceed 1.0 m/s.
The control system automatically start the stand-by oil pump and stop the other oil
pump if the pressure drops below the pre-adjusted set point. The signal for low pressure
comes from a pressure transmitter on the burner
The ignition burner is electrical. This secures a reliable ignition.
OIL SYSTEM OM5560_96#A.2
20-30 / 54 Language UK
Burner operation
1 General
This section describes the burner operation. Figure 1 illustrates the internal oil piping
at the burner; Figure 2 shows the oil flow in different burner modes. Finally Figure 3
illustrates the nozzle valve.
1.1 Start sequence for burners with microprocessor control sys-
tems
Pre-purge takes place with the air quantity of full load. During pre-purge period sole-
noid valves (4), (5), and (8) are closed and solenoid valve (15) is open, see Figure 1
and Figure 2. At the end of the purging period the servomotors turn to the position of
ignition load, solenoid valve (5) and (8) opens and a flushing sequence will take place,
the nozzle valve is purged (pre-heated) during this period. The oil temperature regu-
lation controls that the oil temperature is adequate during purging and atomising pe-
riods.
After the flushing period is completed the solenoid valve (5) will close and the oil in
the pre-heater will be heated. The burner will then go into the ignition step; solenoid
valves (4) and (5) are opened and solenoid valve (3) closed. The electric arc between
the ignition electrodes ignites the oil spraying from the nozzle.
1.2 Burner operation
The oil quantity to be fired is regulated by means of the oil regulator (12) by throttling
the return flow. At partial load the oil regulator is open and at full load closed. During
burner operation the control system drives the servomotors, which again drives the oil
regulator and the air dampers between partial load and full load according to the steam
demand. If the burner shuts down, solenoid valves (4), (5), and (8) close, and solenoid
valve (3) opens. The oil pressure is released from the nozzle valve.
The nozzle valve spring-back closes the needle valve in the nozzle and closes the oil
flow in the nozzle. At full load the atomising pressure is approx. 20-25 bar when
operating on MDO or MGO and approx. 25-30 bar on heavy fuel oil. The return flow
pressure in the oil regulator (12) in ignition position is approx. 7-10 bar and at partial
load 9-12 bar. The return flow pressure is determined according to the position of the
oil regulator.
For safety reason there is a throttle plug in the control flow line fitted to the connection
of solenoid valve (4), with an aperture of 1.5 mm. This plug reduces the strong control
flow, which is directed onto the spring-loaded piston.
BURNER OPERATION OM5560_98#D.1
Language UK 20-31 / 54
Illustration of the oil piping at the burner
1 Nozzle valve
2 Pressure gauge
3 Solenoid valve
4 Solenoid valve and throttle plug
5 Solenoid valve
6 Pressure gauge
7 Pressure transmitter
8 Solenoid valve
9 Thermometer
10 Non-return valve
11 Pre-heater
12 Oil regulator/servomotor
13 Orifice
14 Pressure switch
15 Solenoid valve
16 Temperature transmitter
A Oil to burner
B Oil from burner
Figure 1 oilburn-kbp1x1289790en.wmf
Illustration of the oil flow for burners with microprocessor control systems
Flushing period Atomising period Stop period Purging and flush end periods
Figure 2 oilburn-kbp2ax1293260en.wmf
BURNER OPERATION OM5560_98#D.1
20-32 / 54 Language UK
Illustration of the nozzle valve
1 Body
2 Break spring
3 End cover
4 Hexagonal socket screw
5 O-ring for cover 18.72 x 2.62 V
6 O-ring for piston 12 x 2 V
7 O-ring for bottom plate 18.72 x 2.62 V
8 O-ring for spindle 6 x 2 V
9 Oil nozzle
10 O-ring for oil nozzle 7 x 1.5 V
(for large burners)
11 Cylinder
12 Piston
13 Spindle
C Control circuit
R Return from nozzle
S Outlet to nozzle
L Nominal size of nozzle valve
Figure 3 om5560_98_oilburx0055930en.wmf
BURNER OPERATION OM5560_98#D.1
Language UK 20-33 / 54
Operating instructions
1 General
The following operating instructions are valid for pressure jet burners type KBO-R..M
and KBP with a standard delivery of individual parts for the burner unit and supply
systems from AALBORG INDUSTRIES.
Attention: If the burner unit and supply systems include parts, which are not
standard delivery from AALBORG INDUSTRIES, the specific in-
structions for these parts should be ignored in the following sections.
The actual instructions for the specific parts should be thoroughly
studied and followed during operation of the burner.
The operation instructions in the following sections describe the normal burner oper-
ations with regard to preparation for start-up on the selected fuel type, normal start/
stop, change of fuel, etc. It is implied that the boiler, burner, control system, and ad-
ditional equipment for the boiler plant have been commissioned and are fully opera-
tional.
1.1 Descriptions
1.1.1 Descriptions
In the following sections various operating procedures are described such as:

Diesel oil mode

Heavy fuel oil mode

Normal start/stop

Change from diesel oil operation to heavy fuel oil operation

Change from heavy fuel oil operation to diesel oil operation

Change of heavy fuel oil bunker type

Prolonged stop
2 Operating Instructions
2.1 Diesel oil mode
This section describes the actions that must be carried out before the burner unit and
oil system are operational on diesel oil.
OPERATING INSTRUCTIONS OM5560_99#A.2
20-34 / 54 Language UK
Step A: Check that oil is present in the diesel oil tank. Open the stop valves, which
connect the diesel oil tank to the oil system.
Step B: Select diesel oil on the manually operated three-way valve (G 115). The
control system will indicate diesel oil operation.
Step C: Open the stop valve from the burner return line to the mixing tube and close
the stop valve return to the oil tank.
Step D: Open the inlet stop valves, and the outlet non-return valves for the oil pumps.
Step E: Open the stop valves for the pressure gauges on the oil pumps.
Note: The stop valves for the pressure gauges on the pump unit should only be
opened for pressure control purposes. The stop valves should be closed
during normal operation.
Step F: Open the quick closing valves for the burner unit.
Step G: Start one of the fuel oil pumps and set the other into stand-by mode (if two
are delivered).
Step H: Check that the oil pressure in the ring line is at the correct level.
Step I: The burner is now ready for operation.
2.2 Heavy fuel oil mode
This section describes the actions, which must be carried out before the burner unit
and oil system are operational on heavy fuel oil.
Step A: Check that oil is present in the heavy fuel oil tank. Open the stop valves,
which connect the heavy fuel oil tank to the oil system. To avoid cavitation
of the pumps, the viscosity of the oil in the heavy oil tank should not exceed
380 cSt. If necessary the oil tank should be heated.
Step B: Select heavy fuel oil on the manually operated three-way valve. The control
system will indicate heavy fuel oil operation.
Step C: Open the inlet stop valves, and the outlet non-return valves for the oil pumps.
Step D: Open the stop valves for the pressure gauges on the oil pumps.
Note: The stop valves for the pressure gauges on the pump unit should only be
opened for pressure control purposes. The stop valves should be closed
during normal operation.
Step E: Open the quick closing valves for the burner unit.
Step F: Start one of the fuel oil pumps and set the other into stand-by mode (if two
are delivered).
Step G: Check that the oil pressure in the ring line is at the correct level.
Step H: The burner is now ready for operation.
2.3 Normal start/stop
The control system automatically starts, stops, and regulates the burner in normal op-
eration depending on the steam demand. When the steam pressure is below the set
point for operation, the burner commences the start-up sequence.
OPERATING INSTRUCTIONS OM5560_99#A.2
Language UK 20-35 / 54
In operation mode, the control system attempts to maintain the steam pressure at the
desired set point by regulation of the burner load. The burner can be regulated through
the complete load range from minimum load to full load.
However, should the steam demand decrease below the minimum firing load of the
burner, the steam pressure will increase to the set point for burner stop. The burner
stops and remains stopped until the set point for burner operation is reached again.
2.4 Change from diesel oil operation to heavy fuel oil operation
When the fuel supply is changed from diesel oil operation to heavy fuel oil operation,
the following work steps should be carried out:
Step A: Check that oil is present in the heavy fuel oil tank. Open the stop valves,
which connect the heavy fuel oil tank to the oil system.
Step B: Select heavy fuel oil on the manually operated three-way valve.
Note: When the fuel type is changed from diesel oil to heavy fuel oil, a shut down
for low oil temperature may arise. If the burner is in operation, it will stop
due to this shut down.
Step C: Restart the burner when the low oil temperature shut down can be reset.
Step D: Check that the tracing systems for the oil system are operational.
Step E: Check the heavy fuel oil temperature. The viscosity of the oil at the nozzle
head should be between 14-16 cSt. The pre-heating temperature can be de-
termined by means of the chart in the chapter "Viscosity-temperature chart".
2.5 Change from heavy fuel oil operation to diesel oil operation
When the fuel supply is changed from heavy fuel oil operation to diesel oil operation,
the following work steps should be carried out:
Step A: Check that oil is present in the diesel oil tank. Open the stop valves, which
connect the diesel oil tank to the oil system.
Step B: Select diesel oil on the manually operated three-way valve.
Step C: Check that the tracing of the piping system is off when the burner is in diesel
oil operation.
Caution: Heating of diesel oil in the piping system must be avoided.
2.6 Change of heavy fuel oil bunker type
If the heavy fuel oil bunker type is changed and the calorific value of the oil changes,
the oil/air ratio should be checked and adjusted to obtain the correct combustion data.
For further information about adjustment of the oil/air ratio please see the chapter
Commissioning.
OPERATING INSTRUCTIONS OM5560_99#A.2
20-36 / 54 Language UK
2.7 Prolonged stop
When the boiler plant is stopped for a long period of time, the burner should be shortly
operated on diesel oil before the plant is shut down in order to flush the complete oil
system. Furthermore, tracing must be switched off.
OPERATING INSTRUCTIONS OM5560_99#A.2
Language UK 20-37 / 54
Emergency operation
1 General
In the rare event of a total break down of the control system, the burner unit with
belonging systems can be operated in manual operation (also called emergency oper-
ation). Due to the fact that the majority of the safety interlocks trips and alarms are
overruled in emergency mode, the safety precautions for the plant must be observed
very carefully.
Please note that in emergency operation mode the safety interlocks are reduced
to:

Too low water level

Flame failure

Low combustion air pressure

Warning: When the burner operates in emergency mode, it is very important
that the boiler plant is carefully and continuously supervised by the
ship engineering personnel. Pay special attention to the steam pressure
and water level.
In emergency mode, the burner unit and supply systems are operated from inside the
(local) control panel and the power panel. Various operating switches are provided
inside the panels for operating purposes.
Before emergency operation of the burner is initiated, attempts to restart the control
system must be performed. If restart of the control system is impossible, the work steps
of the following sections must be followed.
2 Manual operation of the burner
2.1 Start and stop of the burner
2.1.1 Start of the burner
Step A: Turn the "/MANUAL" key-operated switch inside (or mounted on the front
of ) the control panel into position manual.
Step B: Start one of the fuel oil pumps on the operating switch inside (or mounted
on the front of) the power panel, "FUEL OIL PUMP 1 START/STOP" or
"FUEL OIL PUMP 2 START/STOP".
Step C: Switch the selector "BURNER MOTOR" to position ON, andthe burner
motor starts.
EMERGENCY OPERATION OM5560_75#B.1
20-38 / 54 Language UK
Step D: Press the "AIR SERVO LOAD UP" push button until the burner reaches its
maximum firing position to purge the furnace. The pre-purge time should
be minimum 60 seconds.
Warning: Insufficient purging may cause danger of furnace explosions. If the
operator suspects that there is a risk of an oil spillage in the furnace,
it must be completely dried out before start of the burner is attempted.
Step E: When the furnace has been sufficiently purged press the "LOAD DOWN"
push button until the burner reaches its minimum firing position.
Step F: Press the "IGNITION" push button and keep it pressed. The ignition trans-
former is energised.
Step G: Press the "OIL VALVES" push button and keep it pressed. At the same time
the safety valves open.
Step H: Release the "IGNITION" and "OIL VALVES" push buttons when the lamp
"FLAME"is illuminated. If the flame is not established within maximum 5
seconds, immediately return to step E.
Step I: When the flame is established the burner remains firing at minimum load.
The burner load can be changed by pressing the push buttons "LOAD
DOWN" and "LOAD UP" for both air servomotor and oil servomotor.
Note: If the flame is distinguished during operation, immediately return to step
D. If the flame cannot be established in the following attempt, please see
the section for faults and rectifying faults.
Note: The automatic water level regulation is not operational in emergency
mode. This means that the water level in the boiler must be adjusted man-
ually.
Step J: In boiler plants with on/off regulation of the water level, one of the feed
water pumps should be started and stopped according to the water level in
the boiler.
Step K: In boiler plants with modulating control of the water level, one of the feed
water pumps should be started. The water level can then be regulated on the
feed water control valve by means of the manually operated hand wheel on
the actuator.
2.1.2 Stop of the burner
Step A: Press the "STOP" push button inside (or mounted on the front of ) the local
control panel to stop the burner. The safety valves immediately close.
Step B: Switch the selector "BURNER MOTOR" to position OFF inside (or
mounted on the front of ) the control panel to stop the burner motor.
EMERGENCY OPERATION OM5560_75#B.1
Language UK 20-39 / 54
Commissioning
1 General
The following commissioning instructions are valid for pressure jet burners type KBO-
E-R..M with a standard delivery of individual parts for the burner unit and supply
systems from AALBORG INDUSTRIES.
Prior to commissioning, the instructions for the individual parts of the burner unit and
supply systems should be studied. The special instructions for the boiler and control
system should also be consulted. The instructions should only be considered as a
guideline. This is due to the fact that each plant should be commissioned individually
to obtain the best burner performance for the specific plant.
Attention: If the burner unit and supply systems include parts, which are not
standard delivery from AALBORG INDUSTRIES, the specific in-
structions for these parts should be ignored in the following sections.
The actual instructions for the specific parts should be thoroughly
studied and followed during commissioning.
During commissioning of the burner unit and supply systems, it might be necessary to
adjust some regulation parameters, timer settings, etc. in the control system to optimise
the function of the plant. These adjustments are not described in the following sections,
but should be carried out as the optimisation requirements emerge. Please see the in-
structions for the control system.
1.1 Pre-service checks
Before commissioning of the burner, the following work steps must be carried out:
Step A: Check that the boiler is ready for operation according to the special instruc-
tions for the boiler.
Step B: Increase or decrease the water level in the boiler to approximately 50 mm
below normal water level.
Step C: Check the electric wiring.
Step D: Switch on the power for the boiler plant and reset the system on the local
panel. Ensure that the burner is in stopped mode.
Step E: Check that the control system is operational according to the special in-
structions for the control system.
Step F: Pre-adjust the set points for boiler operation on the pressure switches and/
or pressure transmitter.
COMMISSIONING OM5560_97#A.2
20-40 / 54 Language UK
1.2 Commissioning adjustments of the burner unit
On delivery from Aalborg Industries, the burner unit has been pre-adjusted to fit the
task. Even though the burner unit has been pre-adjusted, it is advisable to carry out
additional checks during commissioning. These checks are described in the following.
1.2.1 Dismantling
Step A: Ensure that the power is switched off before any work is carried out on the
burner unit.
Step B: Close the quick closing valves for the burner unit.
Step C: Unscrew the screw that holds the burner flange and swing out the burner.
Step D: Dismount the cover for the servo motors.
1.2.2 Adjustment of the combustion head
Step A: Check that the distance between the oil nozzle and diffuser disc is approx-
imately 8 mm.
Step B: Adjust the position of the adjustment ring in relation to the edge of the dif-
fuser disc according to the special instruction for this; see the chapter Com-
bustion head.
Note: Exact distances cannot be given, but has to be determined when the burner
is in operation. It is possible to affect the air velocity and thereby the shape
and quality of the flame by optimising the positions of the adjustment ring
and diffuser disc.
1.2.3 Adjustment of the ignition electrodes
Step A: Check the position of the ignition electrodes and adjust if necessary. Please
see the special instruction Ignition electrodes.
Note: An exact setting of the ignition electrodes cannot be given, but has to be
established when the burner is ignited during operation.
1.2.4 Adjustment of the servomotor
Step A: Disengage the servomotor camshaft from the drive by means of the lever
fitted to the gear box.
Step B: Calibrate the servomotor range in the control system. The low and high range
should be set to 0 and 120 opening of the air dampers respectively.Set the
position of the servomotor to 0, which can be seen on the outer scale. The
raw data line on the control panel displays a numerical value. This value
must be entered in low range menu line.
Step C: Set the position of the servomotor to 120. The new numerical value, which
is displayed in the raw data line, must be entered as the high range.
Step D: Set the time to operate the servomotor from 0 to 120 on the control panel
(normally 15 seconds).
COMMISSIONING OM5560_97#A.2
Language UK 20-41 / 54
Note: Please consider the following proposed settings as guidelines only as the
final settings should be performed after measuring the flue gas (CO2/O2
content). The local control panel settings and cam switch settings depend
on burner size, nozzle size, furnace pressure, etc.
Step E: Pre-adjust the stand-by position (burner stopped) to 0% (0) on the control
panel.
Step F: Pre-adjust the ignition position to 22% (20) on the control panel.
Step G: Pre-adjust the minimum firing position (partial load) to 33% (30) on the
control panel.
Step H: Pre-adjust the purge and full load position to 67% (60) on the control panel.
1.2.5 Assembling
Step A: Mount the cover for the servo motors.
Step B: Close the burner and secure with the screw.
Step C: Switch on power and reset the control system.
1.3 Commissioning of the oil system
When the oil system is commissioned, it should initially be flushed by means of an
external pumping system. This must be done to ensure that the oil system is not clog-
ged-up and to prevent foreign objects from entering the pump unit which might cause
damage.
Warning: When the oil system is commissioned on diesel oil, the tracing of the
piping system must be off.
Step A: Check that oil is present in the diesel oil tank. Open the stop valves, which
connect the diesel oil tank to the oil system.
Step B: Select diesel oil on the manually operated three-way valve. Check that the
control system indicates diesel oil operation.
Step C: Open the inlet stop valves, and the outlet non-return valves for the oil pumps.
Step D: Open the stop valves for the pressure gauges on the oil pumps.
Note: The stop valves for the pressure gauges on the pump unit should only be
opened for pressure control purposes. The stop valves should be closed
during normal operation.
Step E: Open the stop valve for the pressure transmitter and/or switches.
Step F: Close the quick closing valves for the burner unit. Check that the micro
switch is activated and that a shut down appears in the control system.
Step G: Rotate the oil pump by hand to ensure a free and an uninterrupted rotation.
Step H: Adjust the circuit break for the pump to suit full load current of the motor.
The current appears from the motor identification plate and/or the electric
diagrams.
COMMISSIONING OM5560_97#A.2
20-42 / 54 Language UK
Step I: The oil pump must be filled with diesel oil prior to operation. The vent valve
installed on the outlet side of the pump unit must be opened until the air has
escaped from the suction side of the pump. As soon as diesel oil emerges,
the vent valve may be closed.
Step J: Start the oil pump and check that it is running with the correct direction of
rotation. Open the vent valve again until only diesel oil emerges.
Step K: Adjust the oil pressure in the ring line on the pressure regulating valve to
minimum 20.0 barg and maximum 25.0 barg at the burner for diesel oil.
Note: The pressure relief valve installed in each pump is factory set and checked
and should not be adjusted during commissioning.
Step L: Flush the oil system for some time with the oil pump in operation. The total
flushing time should be determined with regard to the size of the oil system
and the amount of impurities (particles, grease, etc.). Check the complete
oil system for leaks.
Step M: When flushing is completed, stop the operational oil pump and clean the oil
filters in the fuel oil supply pump unit. Vent the oil pumps after the filters
have been cleaned.
1.3.1 Check and adjust the pressure transmitter
Step A: Open the quick closing valves for the burner unit.
Step B: Check that the oil pressure indicated on the control panel is identical to the
pressure indicated on the pressure gauge in the oil line.
Step C: Adjust the zero point and/or the span on the oil pressure transmitter if nec-
essary.
1.3.2 Check the low and high alarm for oil pressure and start of stand-by oil pump
Step A: Check and adjust the set point for low and high alarm in the control system.
Step B: Start the oil pump and set the other pump into stand-by mode.
Step C: Decrease the oil pressure on the pressure regulating valve gradually until the
set point is reached. The operating oil pump should stop, and the pump in
stand-by mode should start. The control system should indicate an alarm.
Readjust if necessary.
Step D: Switch operation mode of the pumps and carry out the same procedure.
1.3.3 Check the low oil pressure shut down and trip function
Step A: Check and adjust the set point for low shut down and trip in the control
system.
Step B: Decrease the pressure somewhat more until the set point is reached. The
operating stand-by pump should stop, and a shut down should be indicated
on the control system. Readjust if necessary.
Step C: Readjust the oil pressure to approximately 25.0 barg on the pressure regu-
lating valve and reset the alarms and shut downs.
1.3.4 Check the trip function for overload
Step A: Check the trip function for overload by pressing the test button for the pump
in operation on the circuit breaker.
Step B: The pump stops, and a shut down for pump failure should be indicated in
the control system.
Step C: Reset the circuit breakers and all shut downs after testing.
COMMISSIONING OM5560_97#A.2
Language UK 20-43 / 54
2 Start-up
To continue the commissioning procedures, the oil system must be in normal operation.
Prior to the actual start-up of the burner, some additional checks should be carried out
with regard to ignition and start-up of the burner. When these checks are completed,
the burner should be commissioned on diesel oil and finally on heavy fuel oil.
Attention: Before and during start-up, the furnace must be checked with regular
intervals for oil spillage. If an oil spillage is present in the furnace, the
cause must be determined and the failure must be rectified. The fur-
nace should be purged until it is free of oil.
2.1 Additional commissioning checks
2.1.1 Check the burner motor
Step A: Rotate the burner motor by hand to ensure a free and an uninterrupted rota-
tion.
Step B: Adjust the circuit breaker for the burner motor to suit full load current of the
motor. The current appears from the motor identification plate and/or the
electric diagrams.
Step C: Open the quick closing valves for the burner unit.
Step D: Start the ring line fuel oil pump.
Step E: Operate the burner as described in the chapter Manual operation Press the
BURNER MOTOR push button.
Step F: Check that the burner motor is running with the correct direction of rotation.
Step G: Check that the burner motor does not produce any abnormal mechanical
noises or vibrations.
2.1.2 Check the ignition electrodes
Step A: With the burner motor running press the IGNITION push button and keep
it pressed. The ignition transformer will be energised and the electrodes
ignite.
Step B: Check that the ignition spark appears, re-adjust the electrodes, if necessary,
as described the section Commissioning adjustments of the burner unit.
Step C: Stop the burner motor after the check procedure has been carried out.
2.2 Commissioning on diesel oil
When the burner is commissioned, the boiler pressure and temperature must not be
intensified too rapidly as this might cause stresses in the boiler. The burner should be
kept in minimum firing position during the first commissioning period. The burner
should also only be operated at relatively short intervals during the initial start-up.
When the burner is stopped during this firing-up procedure, the safety interlock shut
downs can be checked and adjusted.
COMMISSIONING OM5560_97#A.2
20-44 / 54 Language UK
2.2.1 Operation of the burner
In automatic mode, the start/stop sequences of the burner are carried out by the control
system. A condition for the initiation of the start-up sequence is that no safety interlock
shut downs are present. If a safety interlock shut down is present, the cause must be
corrected.
The following check of the start-up sequence should be carefully monitored on site to
demonstrate the correct function of the start-up sequence locally.
Step A: Start the fuel oil pump.
Step B: Start the burner from the control system.
Step C: Check that the burner motor starts and that the servo motor opens the air
dampers for purge of the boiler furnace. For visual check of the servomo-
torstemporarily dismount the covers.
Step D: Observe that the furnace is purged for a period of time (minimum 30 sec-
onds) before the servo motor closes the air damper to ignition position.
Step E: Observe that the pre-ignition time is initiated. This means the servo motor-
sare in ignition position and the ignition transformer is energised.
Step F: Check the ignition spark between the electrodes. Use the inspection hole to
visually check the ignition spark. The ignition electrodes should be adjusted
if necessary.
Step G: Check that the burner ignites when the solenoid valves are activated and that
it remains ignited when the power to the ignition electrodes is switched off.
If the flame signal disappears after the end of the safety time the burner is
immediately shut down.
Note: A number of starts may be necessary before the burner ignites. If ignition
of the burner fails despite of several attempts, adjust theoil/air ratio set-
tings, air velocity, and/or oil pressure.
Step H: When firing diesel oil (DO) the oil must be atomised at a pressure of 20
25 bar and on heavy fuel oil (HFO) at a pressure of 25 30 bar.
Step I: The final pressure setting can be seen in the Technical data section.
Step J: Check that the burner is in ignition position after start-up.
Step K: Check that the flame does not pulsate. Adjust the oil/air ratio, and/or air
velocity if necessary.
Step L: Check the shape and colour of the flame. Measure the CO2 and/or O2 content
and adjust the oil/air ratio if necessary.
Step M: Check the colour of the flue gas. Measure the soot spot No. it should not
exceed a soot spot No. of 1-3 (Bacharach). Adjust the oil/air ratio if neces-
sary.
Note: The final adjustment of the combustion parameters should be carried out
when the burner operates on heavy fuel oil as this is the main fuel.
COMMISSIONING OM5560_97#A.2
Language UK 20-45 / 54
2.2.2 Check the stop sequence
Step A: The stop sequence should also be carefully monitored on site. Operate the
burner for a few minutes and stop it from the control system.
Step B: Check that the solenoid valves are activated and that the air dampers are
moved into closed position.
Step C: Check that the burner motor stops.
Step D: Check that the furnace is free of oil spillage.
2.2.3 Setting and testing of the minimum air pressure switch
Step A: When the burner is in operation, check the minimum air pressure switch by
increasing the switch point for the switch. Unscrew the protective cover of
the switch and increase the switch point at the setting wheel. The burner
stops, and a shut down is indicated in the control system.
Step B: Decrease the switch point again. Reset the shut down after testing and start
the burner again.
Step C: Measure the pressure difference between the suction and pressure side of
the fan at minimum burner load. Use this value for determination of the
switch point. It should be approximately 80% of this value.
Step D: Adjust the setting wheel of the minimum pressure switch to the calculated
value and mount the protective cover.
2.2.4 Setting and testing of the high oil pressure switch
Step A: When the burner is in operation, check the high oil pressure switch by de-
creasing the switch point for the switch. The burner stops, and a shut down
is indicated in the control system.
Step B: Decrease the switch point again. It should be adjusted to 6 bar. Reset the
shut down after testing.
2.2.5 Check the safety interlock shut down for flame failure equipment
Step A: When the burner is in operation, check the flame failure equipment by re-
moving one of the flame scanners from the holder and cover the sensor. The
burner stops, and a shut down for flame failure is indicated in the control
system. Reset all shut downs.
Step B: Check and simulate a glowing furnace by using a flash light pointed directly
at the flame scanner.
Step C: Set the burner into start mode. The control system should indicate a shut
down for flame failure.
Step D: Mount the flame scanner into the holder and reset all shut downs.
Step E: Perform the same checks with the other flame scanner.
2.2.6 Check the safety interlock shut down for burner swing out
Step A: When the burner is in operation, unscrew the screw that holds the burner
flange and carefully swing out the burner a few mm. The burner stops, and
a shut down for burner swing out is indicated in the control system.
Step B: Close the burner and secure with the screw. Reset all shut downs.
COMMISSIONING OM5560_97#A.2
20-46 / 54 Language UK
2.2.7 Check the safety interlock shut down for high oil pressure
Step A: When the burner is in operation, check the high oil pressure shut down and
trip function as described in the paragraph Commissioning of the oil sys-
tem. The burner stops, and a shut down for high oil pressure is indicated in
the control system. Reset the shut downs after testing.
2.2.8 Check the trip function for burner motor overload
Step A: When the burner is in operation, check the trip function for burner motor
overload by pressing the test button for the burner motor on the circuit
breaker.
Step B: The burner motor stops and a shut down for burner motor failure is indicated
in the control system.
Step C: Reset the circuit breakers and all shut downs after testing.
2.2.9 Check the safety interlock shut down for too low water level
Step A: When the burner is in operation, perform a live test of both of the water level
safety devises. One of the alarms must be deactivated while testing the other
and opposite.
Step B: Decrease the water level in the boiler by means of the blow-down valves
until the water level has fallen below the too low level mark. After the re-
sponse delay has expired the burner stops and a shut down is indicated in
the control system.
Step C: Increase the water level in the boiler and reset the shut down. Perform the
same test for the other safety device.
Step D: Increase the water level in the boiler and reset all alarms and shut downs.
Activate all safety devices again.
2.2.10 Check the safety interlock shut down for high steam pressure
Step A: When the burner is in operation, raise the boiler pressure until the set point
for high alarm is reached. The control system must indicate a high alarm.
Step B: With the burner in operation, check the shut down and trip function for high
steam pressure. Raise the steam pressure until the burner stops. A shut down
is indicated in the control system.
Step C: If the boiler safety system is equipped with more than one high steam pres-
sure shut down it is necessary to perform the same check with both high
steam pressure shut downs. One of the shut downs must be deactivated while
testing the other and opposite.
Step D: With all steam pressure safety interlocks activated, reset all alarms and shut
downs.
2.2.11 Check the active safety interlock shut downs in emergency operation
Step A: Operate the burner as described in the chapter Manual operation.
Step B: When the burner is in operation, check the active safety interlock shut downs
such as e.g. flame failure, too low water level, etc. as described previously.
2.3 Commissioning on heavy fuel oil
When the burner has been commissioned on diesel oil the final commissioning on
heavy fuel oil can be carried out.
COMMISSIONING OM5560_97#A.2
Language UK 20-47 / 54
2.3.1 Change of fuel
Step A: Stop the burner.
Step B: Check that oil is present in the heavy fuel oil tank. Open the stop valves,
which connect the heavy fuel oil tank to the oil system. To avoid cavitation
of the ring line oil pumps, the viscosity of the oil in the heavy fuel oil tank
should not exceed 380 cSt. If necessary, the oil tank should be heated.
Step C: Check the tracing systems for the oil system and the burner unit is opera-
tional.
Step D: Select heavy fuel oil on the manually operated three-way valve. Check that
the control system indicates heavy fuel oil operation.
Step E: Adjust the oil temperature set point as well as the low and high limit set
points on the temperature controller in the control system; see also the chap-
ter Electric pre-heater. The viscosity of the oil at the nozzle head should
be between 14 - 16 cSt. The pre-heating temperature can be determined by
means of the chart in the chapter "Viscosity-temperature chart".
Step F: Adjust the set points for low shut down, low alarm, and high alarm on the
control panel. Adjust if necessary.
Step G: Start the burner from the control system. It might be necessary to start the
burner several times before the pre-heating temperature is sufficiently high.
Step H: Check that the temperature is raised to the desired set point. Adjust if nec-
essary.
2.3.2 Operation on heavy fuel oil
When the burner is commissioned on heavy fuel oil, final adjustments of the combus-
tion process should be carried out to achieve high quality performance data. The aim
is to operate the burner with lowest possible O2 content and highest possible CO2
content without the risk of an uncompleted combustion (black smoke). At the same
time the reliability of the burner must be ensured.
The oil/air ratio should be checked and adjusted through the complete burner range to
ensure a correct combustion. The oil/air ratio can be checked by measurements of the
soot spot No. and the O2 content and/or the CO2 content in the flue gas. The visual
appearance of the flame should also be checked. If the amount of combustion air to
the burner for given oil flow is too low, the combustion will be uncompleted, and it
produces black smoke. Although the O2 content is low, and the CO2 content is high,
the air flow should be increased. If, on the other hand, the O2 content is high and the
CO2 content is low, it indicates that the air flow for the combustion process must be
decreased.
It is not only the oil/air ratio which is an important factor for the combustion process,
but also the air velocity for the combustion.
The air velocity in the combustion head can be adjusted by moving the adjustment
ringin relation to the flame tubeto change the distance between the adjustment ring and
the edge of the diffuser disc. On low capacity the adjustment ring is advanced and on
high capacity retracted. If the adjustment ring is set too far forward, the combustion
air velocity in the combustion head is too high, the ignition is more difficult or there
is not enough air to support the combustion (high CO content). If the adjustment ring
COMMISSIONING OM5560_97#A.2
20-48 / 54 Language UK
is too far back, the combustion air velocity is too low and the combustion characteristics
become worse (O2 content is too high).
The following commissioning steps imply that the lighting-up procedure of the boiler
is completed and that a sufficient load demand is present to carry out adjustments at
100% load.
Step A: Start the burner and check that it ignites when the ignition is on and the oil
valves are activated. It must also be checked that the burner remains ignited
when the ignition sequence step is completed. Adjust the oil/air ratio setting
in the control system, and/or the air velocity if necessary.
Step B: Start the burner several times to ensure a reliable ignition of the burner.
Step C: Check that the flame is stable and does not pulsate when the burner operates
at ignition load. Carry out measurements of the soot spot No. and O2 content
and/or CO2 content. Adjust the oil/air ratio setting in the control system, and/
or the air velocity if necessary.
Step D: The shape and colour of the flame must also be checked, adjust if necessary.
Note: If the position of the adjustment ring has to be altered in relation to the
diffuser disc, the air velocity and quantity in the combustion head will
change. Check the combustion values by means of flue gas analysis and, if
necessary, adjust the combustion air quantity to be adequate.
Step E: Carry out the same measurements through the complete burner range in steps
of 10% (from minimum load to full load). Adjust the oil/air ratio settingin
the control system if necessary.
Step F: Operate the burner as described in the chapter Manual operation.Carry out
measurements when the burner operates in ignition position. Adjust the oil/
air ratio setting in the control system if necessary.
2.3.3 Check the safety interlock shut down for low and high oil temperature
Step A: Decrease the temperature gradually on the temperature controller located in
the control system until the set point for low shut down is reached. The
burner stops, and a shut down is indicated in the control system.
2.3.4 Check the safety interlock shut down for the pre-heater limit thermostat
Step A: When the burner is in operation, check the high temperature limit thermostat
by dismantling one of the wires at the terminals. The burner stops, and a shut
down is indicated in the control system.
Step B: Connect the wire again and reset the shut down
2.3.5 Additional function checks
Step A: Check/adjust additional safety interlock shut downs if provided. A number
of shut downs might be included in the safety interlock circuit depending on
the specified function and/or the classification society.
COMMISSIONING OM5560_97#A.2
Language UK 20-49 / 54
Maintenance
1 Recommended maintenance intervals
To ensure a safe and reliable function of the burner, inspection must take place with
frequent intervals as described below. The inspection should be carried out by com-
petent and properly trained personnel familiar with the operating and maintenance
procedures relevant for this type of plant.
1.1 Safety regulations for maintenance work
Always ensure that the electrical power is off and that nobody can start the boiler unit
before commencing maintenance work.
All pipes, drums, etc. must be depressurised before any maintenance work is carried
out on these.
1.2 Continuous maintenance
The burner, control panels and other equipment should be kept clean and dry. Check
that no foreign matter accumulates in or around them.
Replace lamps, contactors, and other components when they cease to function or show
signs of deterioration. A part, replaced before it actually fails, could save a costly delay.
1.3 Periodical maintenance
The following check list should be followed frequently. Dependent on the operation
conditions, however, some items may need more attention.
1.3.1 Burner and fuel oil supply system

Check that all connections are tightened and that the wiring is in a good condition.

Check pipe work for leaks, particularly on flanges, joints, and connections. Repair
any leaks which may cause safety risks.

Check that the glands of manual valves are tight enough to prevent easy operation
of the valve. Operate the valves periodically, if possible, to ensure free movement.

Oil filters should be inspected and cleaned if necessary.

Check and clean the flame scanner.

Clean the ignition electrodes and check their setting.

Change the oil nozzle if it is worn or damaged.

Check the combustion values by flue gas analysis.

1.3.2 Electrical system
The electrical and mechanical connections of the local panels and power panels must
be checked and tightened at least once a year.
MAINTENANCE OM5560_85#A.2
20-50 / 54 Language UK
1.3.3 Oil tanks
The oil tanks must be inspected and cleaned at least every four to five years.
MAINTENANCE OM5560_85#A.2
Language UK 20-51 / 54
Faults and rectifying faults
1 Trouble shooting
In the event of fault conditions the basic requirements for correct operation must be
examined first:

Check the electric supply (control and supply voltages).

Check that all regulating and control devices are correctly set.

Are the safety devices in normal operating condition?

Is the burner getting fuel, are valves in the fuel line open, is there oil in the tank?
When it is established, that the fault is not due to the above mentioned, the individual
burner functions and parts must be checked according to the fault finding chart in
Table 1.
Fault finding chart
Caution Possible cause Remedy
Motor
Burner motor does not start. Lockout oc-
curs .
Break in main circuit.
Motor overload relay released.
Faulty motor contactor.
Faulty motor.
Find cause and remedy.
Check setting, reset.
Replace.
Replace.
Burner motor does not start.
Break in motor control circuit:
faulty control unit.
incorrect setting on cam disk in servo motor.
faulty servo motor.
Find cause and remedy.
Replace control unit.
Adjust.
Replace servo motor.
Start failure
Control loop closed (signal lamp of control
loop is lit), but the program of the control
unit does not start.
Incorrect setting on cam disk in servo motor.
Faulty servo motor.
Faulty control unit.
Adjust.
Replace.
Replace.
Burner motor starts, program remains at pre-
purge period.
Servo motor does not reach the position of
full load of air dampers:
faulty servo motor.
faulty limit switch in servo motor.
incorrect setting on cam switch.
jammed air dampers.
Replace.
Replace.
Check and adjust.
Check and adjust.
Ignition failure
Burner motor starts, control voltage from
control unit to ignition transformer is
switched on, no ignition and after a short
time lockout occurs.
Dirty or worn ignition electrodes, insulator
cracked.
Ignition electrodes too far apart.
Cable damaged.
Faulty ignition transformer.
Clean or replace.
Adjust according to instructions.
Replace.
Replace.
FAULTS AND RECTIFYING FAULTS OM5560_92#B.1
20-52 / 54 Language UK
Fault finding chart
Caution Possible cause Remedy
No flame formation
Burner motor starts, ignition is in order, noz-
zle supplies no oil or nozzle valve does not
function. After a short time lockout occurs.
Solenoid valve does not function:
faulty solenoid valve or coil.
cable damaged.
faulty control unit.
nozzle needle does not open.
faulty O-ring in nozzle.
Possible couse oil to hot and evaporates in-
stead of forming a flame.
Replace.
Replace.
Replace.
Replace.
Replace.
Remedy ensure heater and tracing is
off.
Oil pressure too low. Direction of rotation in burner motor wrong. Reconnect motor.
Main oil valve does not open.
Pressure of return oil is too high.
Faulty pressure switch (max.).
Find cause and remedy.
Replace.
Oil pump
Supplies no oil or atomising pressure is too
low.
Dirty filter.
Leaking suction line of transfer pump.
Pump capacity decreases due to faulty or
worn pump.
Clean.
Seal.
Replace.
Severe mechanical noise.
Pump sucks air.
Too low inlet pressure to pump.
Tighten joints.
Clean filter, check and adjust pres-
sure.
After flame establishment lockout occurs
Flame forms. When burner runs to full load,
flame extinguishes and lockout occurs.
Incorrect burner adjustment.
Dirty filters.
Blocked nozzle.
Adjust.
Clean.
Replace.
Flame forms. Shut down occurs and then re-
start.
Oil temperature is too low:
pre-heater faulty or its capacity inadequate.
incorrect setting on lower limit thermostat.
Repair or replace.
Check and adjust temperature of in-
coming oil.
Oil flows into the furnace
Oil flows into the furnace during shut down.
Nozzle valve and main oil valve or nozzle
valve and non-return valve do not close.
Clean, repair or replace.
Oil flows into the furnace during pre-purge
period.
Leaking nozzle valve. Clean, repair or replace.
Flame monitoring fault
Burner motor starts, flame forms and then
lockout occur.
Incorrect position of flame detector.
Dirty flame detector.
Illumination (flame) too weak.
Faulty flame detector.
Faulty control unit.
Adjust.
Clean.
Check burner adjustment.
Replace.
Replace.
Lockout during pre-purge period.
Faulty flame detector.
Faulty control unit.
Incorrect flame signal due to extraneous
light.
Replace.
Replace.
Find cause and remedy.
FAULTS AND RECTIFYING FAULTS OM5560_92#B.1
Language UK 20-53 / 54
Fault finding chart
Lockout during shut down.
Faulty or aged flame detector.
Faulty control unit.
Nozzle valve and main oil valve or nozzle
valve and non-return valve do not close.
Replace.
Replace.
Clean, repair or replace.
Combustion head
Diffuser disc burned out. Worn out. Replace diffuser disc, if necessary.
Inside oily or has heavy carbon deposits.
Distance between diffuser disc and nozzle
incorrect.
Incorrect combustion air adjustment.
Furnace not adequately ventilated.
Nozzle incorrect sized or of wrong type.
Nozzle worn.
Too small partial load.
Adjust.
Adjust.
Increase air supply.
Change nozzle as appropriate.
Replace.
Increase.
Table 1
FAULTS AND RECTIFYING FAULTS OM5560_92#B.1
20-54 / 54 Language UK
Table of contents
MISSION control system
Description Document ID Page
.
Touch control system................................................. SD9306_05............... 21-2
TABLE OF CONTENTS
Language UK 21-1 / 4
Touch control system
1 General
The MISSION Control Touch control system is designed to provide safe and func-
tional operation of the boiler plant both at the boiler and from a remote location such
as the engine control room. The general design is a common panel solution. Each panel
is capable of controlling one oilfired boiler and one exhaust gas boiler and consist of
a local control part and a power part integrated into one panel. The panel is locally
controlled by means of a touch screen in the front of the panel.
Figure 1 illustrates a typical configuration for a boiler system. The example shown is
for a MISSION'OS boiler plant with a MISSION XS exhaust gas boiler. The con-
trol system is constructed in a similar way for other single boiler installations.
The communication between the common panel and touch screen is achieved through
a 2-wire RS485 network. The cable type is a twisted pair with shield. The 2 x 0.5-1.5
mm
2
cable should not exceed 1000 metres in total length.
Illustration of the control system

RS485
Ethernet
Figure 1 contouch_01x0195512en.wmf
Common panel
The common panel holds two MISSION controllers, communication interface, re-
lays, flame monitoring equipment, water level control equipment, switches for emer-
gency operation but also power supply systems, motor starters and optional compo-
nents like smoke density monitoring system, salinity alarm equipment, oil detection
equipment, etc.
TOUCH CONTROL SYSTEM SD9306_05#B.1
21-2 / 4 Language UK
The cabinet gives an IP 55 insulation class and can be located in ambient temperatures
between 0-55C with a relative humidity up to 90%. The maximum vibration level is
100 Gal at 10-30 Hz. And the power supply is 115 or 230 V AC, 45-65 Hz. The
maximum power consumption of the local panel is approximately 50 VA.
The two MISSION controllers constitute a computerised control and monitoring
system. The panels are equipped with a number of digital and analogue input/output
connections. These input and output connections are handled by the CPU, which op-
erates the panels. Two EPROMs contain the programme, and an E
2
PROM stores
specified plant data.
One of the controllers handles local control of the boiler plant such as e.g. fuel system
and plant settings. The other controller is the common controller and handles common
tasks such as e.g. control of the fuel oil- or, if provided, feed water pumps.
The complete boiler system can be operated from the controllers inside the local panel
with or without the touch screen in service. By use of the soft keys placed to the left
of the display, the burner can be operated in manual mode, and shut downs/alarms can
be acknowledged. The soft keys placed to the right of the display give access to the
menu structure. The actual menu levels or menu item lines are displayed on the four
line Liquid Crystal Display (LCD). Figure 2 illustrates the interface on the controllers.
It is also via these controllers that the basic configuration of the system is done during
commissioning. Access to a number of different parameters, settings, etc. is limited by
password entering. This secures the operation from unintentional entering and modi-
fication, which might cause damage to the boiler plant. The password routine is divided
into two steps. The entering of the common user password provides access to the most
common menu items, and the super user password, which is only known by Aalborg
Industries, provides access to the more vital functions.
Illustration of the controller interface




Figure 2 contouch_02x0197680en.wmf
Monitoring and control from the touch screen
The control system is provided with a touch screen with a graphic user interface for a
clear view of the boiler operation. This touch screen can be installed anywhere, as long
as the length of the cables does not exceed 1000 metres. The boiler plant can be moni-
tored and operated from the touch screen as well as from the local panels. Furthermore,
trend curves for the plant can be viewed and alarms can be acknowledged.
In Figure 3 the main screen of the touch screen is shown. By use of the touchscreen,
shut downs/alarms can be acknowledged from the bell-button in the upper right corner.
The buttons on the right side of the display give access to detailed information on the
steam system (and, if present, exhaust gas boiler), feed water system, fuel system and
burner operation. From the buttons on the left side of the touch screen, key lock, trend
curves and the set-up menu can be accessed. The button [BOILER] gives access to an
overview of the operation of the boiler system.
TOUCH CONTROL SYSTEM SD9306_05#B.1
Language UK 21-3 / 4
Illustration of the main page of the touch screen
Figure 3 contouch_03x0197690en.wmf
A password system provides the logged-on user with permissions/restrictions and en-
sures that no parameters can be changed by unauthorised personnel.
Mod-bus interface
An optional communication interface via Modbus protocol (RS485) to other systems
on board the ship can be provided (see).
The Modbus interface feature offers external control and monitoring of a limited num-
ber of parameters in the boiler control system from an external operating place such
as e.g. the cargo control room. It is possible to control and/or monitor parameters such
as boiler operation mode, state (stopped, starting, purge, etc.), manual start/stop and
load, selection of master/slave boiler, inert gas mode (if provided), boiler/system pres-
sure, and water level.
If Modbus is selected, Aalborg Industries supplies a complete address list and a sep-
arate communication port on the touch screen including a 9-pin DB9 plug.
Remote desktop
The system supports remote desktop using a web browser. Communication is carried
out over an ordinary Ethernet network (see Figure 1) using an Ethernet cable with RJ45
connectors (not supplied by AI).
With the remote desktop feature it is possible to remote control the touch display seeing
the same picture as on the actual touch screen and using the computer mouse as input
device instead of ones finger.
For details please refer to the document Touch Remote Desktop.
TOUCH CONTROL SYSTEM SD9306_05#B.1
21-4 / 4 Language UK
Table of contents
Operation of the panels
Description Document ID Page
.
Operation of the panels............................................... OM9306_58.............. 22-2
Operation of the touch screen...................................... OM9306_57.............. 22-17
Key operation lock..................................................... OM9306_55.............. 22-28
TABLE OF CONTENTS
Language UK 22-1 / 32
Operation of the panels
1 General
The MISSION Control Touch (MCT) control panel is usually equipped with both a
local controller and a common controller. The local controller controls the oil fired
boiler and burner operation, and the common controller controlscommon items and
accessories such as fuel oil pumps, feed water pumps, exhaustgas boilers, salinity, etc.
On MCT systems normal operation will be carried out from the touch screen but for
system configuration or in case the touch screen breaks down operation is carried out
from the controllers. Figure 1 illustrates the local controller and the operation of the
soft keys.
Illustration of a controller
USER DEFINED VALUE 1
USER DEFINED VALUE 2
USER DEFINED VALUE 3
[STATE] [MODE]
[VALUE 1]
[VALUE 2]
[VALUE 3]
[LOAD%]
BOILER PRES
F.OIL TEMP
F.OIL PRES
STOPPED
0.0 BAR
0
0.0
0%
C
BAR

Moves further out of a branch in the

menu structure and changes digit
position towards left.
Move further into a branch in the
menu structure and changes digit
position towards right.
Moves upwards in the menu structure
and increases to a higher value.
Moves downwards in the menu structure
and decreases to a lower value.
Entering of different menu items for
modification of settings, parameters,
etc. Password entering is required
when this soft key is used.
Display for surveillance of operation, servicing, and modification.
The display is a 4-line display with maximum 20 characters in each line.
If the sign is indicated the boiler plant is operating in inert gas mode.
If the sign is indicated the boiler plant is stopped by an external stop.
If the sign is indicated the key operation lock is opened.
Manual increase of the burner load. This
facility is only available in manual operation
mode. Or manual increase of other remote
control settings = 1.
Manual decrease of the burner load. This
facility is only available in manual operation
mode. Or manual decrease of other remote
control settings = 1.
Starts the burner in manual operation mode.
The green LED above the soft key flashes.
When a feedback signal for combustion air
fan running is received, the LED shines.
Stops the burner in manual operation mode.
The green LED above the ON soft key is
switched off simultaneously.
Selection between automatic and manual
operation mode. The yellow LED above
the soft key shines in manual operation
mode.
[ ]
Acknowledgment of alarms and shut downs.
Low frequent flashes on the red LED
above the soft key indicate alarms, and
high frequent flashes indicate shut downs/
burner cut-off.
Figure 1 om9306_58_unisabx0062900en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-2 / 32 Language UK
By use of the soft keys placed to the left of the display, the burner can be operated in
manual mode, and shut downs/alarms can be acknowledged. Furthermore, a number
of remote controls (e.g. oil pressure, water level, etc.) can be operated/controlled from
here provided the actual remote control setting is selected to "1" in the menu structure.
The soft keys placed to the right of the display give access to the menu structure. The
actual menu levels or menu item lines are displayed on the four line crystal display
(LCD).
The menu structure for the local and power panels can be found elsewhere in this
manual.
The communication between the panels included in a boiler plant is achieved through
wire connections.
2 Operating examples
In this section a number of operating examples are illustrated. The operating principles
in the examples shown are identical for all other boiler and burner types. This means
that regardless of the parameter, setting, etc., which should be entered or modified, the
procedure for operating the panels is the same.
Examples No. 2 to No. 5 imply that the key operation lock is unlocked. If this is not
the case then please refer to example No. 1 or the specific instruction for unlocking
the key operation lock.
The following operating examples are shown:

Operating example No. 1:

- Unlock of the key operation lock for local panel 1. See Figure 2 and Figure 3.

Operating example No. 2:

- Change of burner operation mode from stopped mode to automatic mode. See
Figure 4, Figure 5, and Figure 6.

Operating example No. 3:

- Change of set point for low steam pressure alarm. See Figure 7, Figure 8, and
Figure 9.

Operating example No. 4:

- Inspection of the shut down list. See Figure 10, Figure 11, and Figure 12.

Operating example No. 5:

- Manual start and stop of the burner. See Figure 13 and Figure 14.
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-3 / 32
Example No. 1: unlock the key operation lock
BOILER PRES
F.OIL TEMP
F.OIL PRES
STOPPED
0.0
0
0.0
0%
BAR
C
BAR

PP1
NO
0%
KEY POSITION
REQUEST KEY
STOPPED
Press once
Press once
Continued in next picture
Press once
KEY POSITION
REQUEST KEY
STOPPED
PP1
0%
NO
Figure 2 om9306_58_unisabx0063020en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-4 / 32 Language UK
Example No. 1: unlock the key operation lock (continued)
Press once
Press once
Continued from previous picture
KEY POSITION
REQUEST KEY
STOPPED
KEY POSITION
RELEASE KEY
STOPPED
PP1
0%
YES
LP1
NO
0%
BOILER PRES
F.OIL TEMP
F.OIL PRES
STOPPED
0.0
0
0.0
0%
BAR
C
BAR

Figure 3 om9306_58_unisabx0063030en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-5 / 32
Example No. 2: Change of operation mode
BOILER PRES
F.OIL TEMP
F.OIL PRES
STOPPED
0.0
0
0.0
0%
BAR
C
BAR

PARTNER
CMN CTRL
SURVEIL
SETUP
BOILER
FUEL OIL
AIR
COMBUST
BOILER
FUEL OIL
AIR
COMBUST
PARTNER
CMN CTRL
SURVEIL
SETUP
Press twice
Press 7 times
Press once
Continued in next picture
Figure 4 om9306_58_unisabx0062910en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-6 / 32 Language UK
Example No. 2: Change of operation mode (continued)
LOGGINGS
CALIBRATE
CONFIG
LANGUAGE
CTRL MODE
TIMERS
SETTINGS
DIAGNOSES

STOPPED
LOW
BURNER CTRL MODE
SETPOINT SELECT

LOW
STOPPED
BURNER CTRL MODE
SETPOINT SELECT
Press once
Press once
Press once
Continued in next picture
Continued from previous picture
Figure 5 om9306_58_unisabx0062920en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-7 / 32
Example No. 2: Change of operation mode (continued)

LOW
AUTO
BURNER CTRL MODE
SETPOINT SELECT

AUTO
LOW
BURNER CTRL MODE
SETPOINT SELECT
BOILER PRES
F.OIL TEMP
F.OIL PRES
STARTING
0.0
0
0.0
0%
BAR
C
BAR

Press once
Press 4 times
Continued from previous picture
Figure 6 om9306_58_unisabx0062930en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-8 / 32 Language UK
Example No. 3: Change of set point
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
16.5
120
22.0
0%
BAR
C
BAR

PARTNER
CMN CTRL
SURVEIL
SETUP
BOILER
FUEL OIL
AIR
COMBUST
BOILER PRES
WATER LEVEL
COMMON PRES
READY
HI.SHT.DWN.
HIGH ALARM
LOW ALARM
REG OUTPUT
Press twice
Press once
Press twice
Press once
16.5
20
16.5
0%
BAR
BAR
18.0
17.5
4.0
0.0 %
BAR
BAR
BAR
Continued in next picture
Figure 7 om9306_58_unisabx0062940en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-9 / 32
Example No. 3: Change of set point (continued)

SET TO ACCEPT / QUIT
Press once for
a few sec.
Press once
Press twice
Press once
HI.SHT.DWN.
HIGH ALARM
REG OUTPUT
LOW ALARM
18.0
17.5
4.0
0.0 %
BAR
BAR
BAR
PASSWORD
234 1
HI.SHT.DWN.
HIGH ALARM
LOW ALARM
REG OUTPUT
18.0
17.5
+ 04.0
0.0 %
BAR
BAR
BAR 0
HI.SHT.DWN.
HIGH ALARM
LOW ALARM
REG OUTPUT
18.0
17.5
+00 .0
0.0 %
BAR
BAR
BAR 4
Continued from previous picture
Continued in next picture
Figure 8 om9306_58_unisabx0062950en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-10 / 32 Language UK
Example No. 3: Change of set point (continued)
HI.SHT.DWN.
HIGH ALARM
LOW ALARM
REG OUTPUT
18.0
17.5
+00 .0
0.0 %
BAR
BAR
BAR 5
Press once
Press 4 times
18.0
17.5
5.0
0.0 %
BAR
BAR
BAR
HI.SHT.DWN.
HIGH ALARM
REG OUTPUT
LOW ALARM
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
16.5
120
22.0
0%
BAR
C
BAR

Continued from previous picture

Figure 9 om9306_58_unisabx0062960en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-11 / 32
Example No. 4: Inspection of the shut down list
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
7.5
120
12.0
0%
BAR
C
BAR

PARTNER
CMN CTRL
SURVEIL
SETUP
BOILER
FUEL OIL
AIR
COMBUST
BOILER
FUEL OIL
AIR
COMBUST
PARTNER
CMN CTRL
SURVEIL
SETUP
Press twice
Press 7 times
Press once
Continued in next picture
Figure 10 om9306_58_unisabx0062970en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-12 / 32 Language UK
Example No. 4: Inspection of the shut down list (continued)
LOGGINGS
CALIBRATE
CONFIG
LANGUAGE
CTRL MODE
TIMERS
SETTINGS
DIAGNOSES
DATA LOG
OIL SUMMARIZER
INSPECT SHT.DWN. LOG
Press 4 times
Press once
Press once
CTRL MODE
TIMERS
SETTINGS
DIAGNOSES
LOGGINGS
CALIBRATE
CONFIG
LANGUAGE
Continued in next picture
Continued from previous picture
Figure 11 om9306_58_unisabx0062980en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-13 / 32
Example No. 4: Inspection of the shut down list (continued)
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
7.5
120
12.0
0%
BAR
C
BAR

Press soft key to

inspect shut down list
(maximum 20 shut downs)
Press 5 times
SHT.DWN.
FUEL OIL PRES LOW
990530-1230
Continued from previous picture
SHT.DWN. 990530-1230
FUEL OIL PRES LOW
Figure 12 om9306_58_unisabx0062990en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-14 / 32 Language UK
Example No. 5: Manual start/stop
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
7.5
120
22.0
0%
BAR
C
BAR

Press once for manual

operation mode if auto
is selected in the
SETUP/CONTROL MODE
Press to increase
the burner load
Press once, and the
burner initiates a
start up sequence
BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
7.5
120
22.0
0%
BAR
C
BAR

BOILER PRES
F.OIL TEMP
F.OIL PRES
MAN LOAD
7.5
120
22.0
10%
BAR
C
BAR

Continued in next picture

Figure 13 om9306_58_unisabx0063000en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
Language UK 22-15 / 32
Example No. 5: Manual start/stop (continued)
Press once to
stop the burner
BOILER PRES
F.OIL TEMP
F.OIL PRES
MAN LOAD
7.5
120
22.0
50%
BAR
C
BAR

Press to decrease
the burner load
BOILER PRES
F.OIL TEMP
F.OIL PRES
MAN LOAD
8.2
120
22.0
10%
BAR
C
BAR

BOILER PRES
F.OIL TEMP
F.OIL PRES
READY
8.0
120
22.0
0%
BAR
C
BAR

Continued from previous picture

Figure 14 om9306_58_unisabx0063010en.wmf
OPERATION OF THE PANELS OM9306_58#A.2
22-16 / 32 Language UK
Operation of the touch screen
1 General
The control system is equipped with a touch screen, where the system can be controlled
and overviewed from. The boiler operation, which can be performed from the local
panel(s) can also be performed from the touch screen. Operation by use of the local
panels can be found elsewhere in the manual. Figure 1 illustrates the main picture of
the touch screen.
Main picture of touch screen
Figure 1 om9306_57_pic_0x0062860en.wmf
[ALARM]: The alarm button in the upper right corner is accessable from any screen
view. This button gives access to acknowledge alarms and view the alarm list.
[STEAM] The steam button gives access to an overview of the steam system, to set
alarm limits, to control the feedwater pumps and to access an overview of the ex-
haustgas boiler if present.
[WATER] The water button gives access to an overview of the feedwater system, to
set the alarm limits, and to control the feedwater pumps.
[FUEL] The fuel button gives access to an overview of the fuel system, to set the alarm
limits, and to control the fuel pumps.
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-17 / 32
[BURNER] The burner button gives access an overview of the burner system including
fans and to set alarm limits.
[BOILER] The boiler button gives access to an overview of the performance of the
boiler system. Alarm limits for the system can be set.
[KEY] The key button gives access to get and release the key for operation.
[TREND] The trend button gives access to trend curves of the performance of the boiler
system.
[SET-UP] The set-up button gives access to the set-up menu, e.g. timers, plant limits,
and diagnostic information. This menu is described elsewhere in the manual.
The key in the top left corner indicates if present that the user has unlocked the system
and therefore can modify different parameters.
2 Operating examples
In this section a number of operating examples are illustrated. The examples show a
generic boiler with a KBP burner attached but the operating principles are identical for
all other boiler and burner types. This means that regardless of the parameter, setting,
etc., which should be entered or modified, the procedure for operating the touch screen
is the same.
Examples No. 2 to No. 5 imply that the key operation lock is unlocked. If this is not
the case then please refer to example No. 1 or the specific instruction for unlocking
the key operation lock.
The following operating examples are shown:

Operating example No. 1:

- Unlock of the key operation lock for touch screen. See Figure 2 for a general
method and Figure 3 for a shortcut in parameter menues.

Operating example No. 2:

- Change of burner operation mode from stopped mode to automatic mode. See
Figure 4 and Figure 5.

Operating example No. 3:

- Change of set point for low steam pressure alarm. See Figure 6 and Figure 7.

Operating example No. 4:

- Inspection of the shut down list. See Figure 8.

Operating example No. 5:

- Manual start and stop of the burner. See Figure 9 and Figure 10.
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
22-18 / 32 Language UK
Example No. 1: unlock the operation lock


PP1
Request key:


PP1
Request key:


PP1
Request key:
Figure 2 contouch_108x0200400en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-19 / 32
Example No. 1: unlock the operation lock in a parameter menu
Figure 3 contouch_116x0200480en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
22-20 / 32 Language UK
Example No. 2: change of operation mode
Figure 4 contouch_109x0200410en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-21 / 32
Example No2: change op operation mode (contionued)
Figure 5 contouch_110x0200420en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
22-22 / 32 Language UK
Example No. 3: change of set point
Figure 6 contouch_111x0200430en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-23 / 32
Example No. 3: Change of set point (continued)
Figure 7 contouch_112x0200440en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
22-24 / 32 Language UK
Example No. 4: Inspection of the shut down list
Figure 8 contouch_113x0200450en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-25 / 32
Example No. 5: Manual start/stop
Figure 9 contouch_114x0200460en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
22-26 / 32 Language UK
Example No. 5: Manual start/stop (continued)
Figure 10 contouch_115x0200470en.wmf
OPERATION OF THE TOUCH SCREEN OM9306_57#A.2
Language UK 22-27 / 32
Key operation lock
1 General
In the following the key operation lock system for the control system is described with
regard to function and operation.
1.1 Function
Operation of the boiler plant must be performed from the local panel(s) or the PC, if
provided. To ensure that operation of the boiler plant can only take place from one
place at the time, the control system is provided with a key operation lock system. This
prohibits unintentional alterations of settings, parameters, etc., which might cause
damage to the complete boiler plant. Even though the control system is locked, it still
controls the boiler plant automatically, and complete monitoring is also possible. Only
the operation of the boiler plant is limited.
However, it is possible to change between manual and automatic operation modes on
the local panel provided that the burner has been set to "AUTO" operation.
1.2 Operation
When the control system is powered up, the operation of the boiler plant is as default
set for key operation lock position to power panel 1. But as all operation of the boiler
plant must be performed from a local panel or PC, the system is locked. To unlock the
operation of the control system, the position of the key operation lock must be changed.
The key operation lock can be in one of the following positions:
- PP1 (power panel 1)
- LP1 (local panel 1 this is also the position when using the touchscreen)
- LP2 (local panel 2, in twin boiler plants)
- PC (computer, in boiler plants with steam atomising burners)
In order to operate the boiler plant, the key operation lock must be opened on either
one of the local panels, on the touch screen, or on the PC. Then operation can take
place from the opened place (local panel 1, local panel 2, touch screen, or PC). Please
note that an operation place can only be selected if the position of the key operation
lock is at PP1 (power panel 1).
1.2.1 Operation from a local panel
Step A: When the front menu is displayed on the local panel press the soft key
once, and the menu for the key operation lock appears in the local panel
display. The top menu line shows the actual position of the key, and in the
next line an opening of the key can be requested on the actual panel.
Step B: Press the SET soft key, and the black bar will be placed in the [NO] position.
Step C: Press the soft key, and [YES] appears in the position of the black bar.
KEY OPERATION LOCK OM9306_55#A.2
22-28 / 32 Language UK
Step D: Press the SET soft key again, and the actual local panel will be active for
operation. The display of the actual key position in the top menu line changes
to the actual local panel (LP1 or LP2).
An unlocked local panel is also indicated by a key symbol in the bottom menu line.
1.2.2 Operation from the touch screen
The key status is always indicated in the top left part of the picture. When a key is
shown, the system is unlocked. If the key is not shown or blinking (warning the user
when in a parameter menu), the system is locked. There are two ways of unlocking the
system when using the touch panel.
Method 1 - Advanced:
Step A: This method can e.g. be used for checking who currently holds the key. In
the mainpictureof the touch panel press the [KEY] button in the left side of
the screen, and the menu for the key operation lock appears in the display.
Illustrated in Figure 1
Step B: The top field indicates current key position. The buttom key (dark grey)
indicates if the system is unlocked. [Yes] means that it is unlocked and [NO]
means the system is locked. By pressing the button one can toggle between
the two.
Method 2 quick access:
Step A: This method is useful when setting parameters (requiring the key). To avoid
having to leave the current parameter picture to unlock the system one can
instead just press the key to toggle the status. Illustrated in
Notice that as the key is being retrieved, the button says get to indicate to the
user that the system is working.
KEY OPERATION LOCK OM9306_55#A.2
Language UK 22-29 / 32
Illustration of key operation - method 1
Figure 1 contouch_106x0197660en.wmf
KEY OPERATION LOCK OM9306_55#A.2
22-30 / 32 Language UK
Illustration of key operation - method 2
Figure 2 contouch_107x0197670en.wmf
Note: If any operation has not taken place within one minute, the key operation
lock automatically changes back to PP1 (power panel 1). A new unlocking
procedure must be performed before any operation can take place. Please
note that the time period for automatic change back to PP1 can be set to a
different value in the timer set-up menu. The name of the timer is "KEY
HOLD".
1.2.3 Operation from a PC
When operation from a PC should be performed, the key operation lock must be opened
on the PC. If the key operation lock is not opened, it is still possible to open all sub-
menus and dialog boxes, but it is not possible to perform any changes of settings,
parameters, operation modes, etc. For PC monitoring and control systems using Win-
dows 3.11 buttons are faded out and thereby inactive. For PC systems using Windows
2000 a dialog box for key request pops-up.
The number of key operation locks depends on the number of configured boiler systems
for the actual plant, e.g. one MISSION OL boiler and one MISSION OC boiler
will include two key operation locks.
Step A: For PC systems using Windows 3.11 place the cursor on the padlock (brown
colour) located in the right side of the PC screen and click once on the mouse.
The symbol changes from a locked padlock to an open padlock. Further-
more, the colour changes from brown to green.
Step B: For PC systems using Windows 2000 click the access field located in the
address/icon bar and request the key operation lock in the dialog box which
pops-up. The colour of the access field changes from white to green.
KEY OPERATION LOCK OM9306_55#A.2
Language UK 22-31 / 32
Note: It might be necessary to enter the user ID and pass code before the key
operation lock can be changed. By requesting the lock, the operator will
be asked for the entering of user ID and pass code.
Step C: Operation of the boiler plant can now take place from the PC.
Note: If any operation has not taken place within one minute, the key operation
lock will automatically change back to PP1 (power panel 1). A new un-
locking procedure must be performed before any operation can take place.
Please note that the time period for automatic change back to PP1 can be
set to a different value in the timer set-up menu on the local panel(s). The
name of the timer is "KEY HOLD".
1.3 Commissioning
In order to ease the commissioning work the key operation lock system is provided
with a feature which makes it possible to operate the control system from all operation
places. In the menu SETUP/CONFIG/BURNER OPTION on the local panel the key
operation lock can be disabled "DISABLE KEY". Thus with the key operation lock
disabled on the local panel(s), operation can be carried out from all operation places.
E.g. in a twin boiler plant with steam atomising burners and no touchscreen, operation
can take place from LP1 (local panel 1), LP2 (local panel 2), and the PC (computer).
However, the time period for non-operation of the local panel is still active. So it might
be advisable to set this time hold period to a higher value during commissioning. The
time period value can be changed in the SETUP/TIMERS/TIMER SETUP/SUR-
VAILLANCE menu and the name of the timer is "KEY HOLD". After commissioning
the timer must be set back to its original value.
KEY OPERATION LOCK OM9306_55#A.2
22-32 / 32 Language UK
Table of contents
Commisioning and service
Description Document ID Page
.
Commissioning and service........................................ OM9306_59.............. 23-2
Monitoring and control via touch screen....................... OM9306_56.............. 23-20
TABLE OF CONTENTS
Language UK 23-1 / 78
Commissioning and service
1 General
The following sections describe some of the parts provided in the controller and the
actions which must be performed when the controller is commissioned or serviced.
The controller is designed as a computerised control and monitoring unit which pro-
vides the boiler plant with the necessary functions to have a safe and reliable operation.
The main parts of the controller consist of:

The cabinet.

The keyboard with soft keys for operation and entering the menu structure.

The four line crystal display (LCD).

The relay print, which includes the battery, relays, fuse, and connections for wiring,
power supply, and communication.

The DI relay print for additional digital input connections.

The CPU print, which includes the CPU, EPROM, and EEPROM. The CPU print
is fitted onto the relay print.
Each MISSION Control Touch (MCT) panel consists of a local controller and a
common controller. For double boiler plants only one of the panels hold a common
controller though.
Figure 1 shows the keyboard and display, and Figure 2 shows the inside of the controller
(local controller).
Please note that the operation of the soft keys and the structure of the menus are not
described in this chapter, but can be found elsewhere in the instruction manual.
Illustration of the keyboard and display
USER DEFINED VALUE 1
USER DEFINED VALUE 2
USER DEFINED VALUE 3
[STATE] [MODE]
[VALUE 1]
[VALUE 2]
[VALUE 3]
[LOAD%]
Figure 1 om9306_59_unisabx0063040en.wmf
COMMISSIONING AND SERVICE OM9306_59#A.2
23-2 / 78 Language UK
Illustration of the inside of the controller
Panel cabinet Connection for
keyboard
Connection for
display
Terminal row
Terminal row
Battery
EPROM
EEPROM
CPU
CPU print
Relay print
Fuse
Voltage jumper
Reset LED (red)
Idle LED (green)
Power LED (red)
Relays
Digital input LEDs (green)
Digital output LEDs (red)
Communication LED (green)
Communication LED (red)
Communication LED (yellow)
Terminal row
DI relay print
Terminal row
RC jumper
External communication plug
PNP/NPN jumper
Figure 2 om9306_59_unisabx0063050en.wmf
The technical data for the controlleris:
Power supply: 115/230 VAC, 45-65 HZ
Voltage tolerance: +10 to -15%
Consumption: 50 VA
Ambient temperature: 0-55C (operation)
Humidity: 20-90% relative humidity (not condensing)
Density: IP 54
Vibration: maximum 100 Gal at 10-30 Hz
1.1 Light diodes
Both the relay print and CPU print are equipped with a number of light diodes (LEDs).
The LEDs can be used during commissioning or servicing to determine the state of the
input/output signals, communication signals, etc. When the hinged door is open, the
LEDs can be inspected. The printed circuit boards are equipped with the following
LEDs:
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-3 / 78

Digital input (12 LEDs, green).

Digital output (18 LEDs, red).

Communication (3 LEDs, red, yellow, and green).

Supply (1 LED, red).

CPU (2 LEDs, red and green).

The position and identification of the LEDs are shown in Figure 2.
Digital input
The green LEDs are marked from DI1 to DI12. The attached functions appear from
the electrical diagrams. When a specific LED is illuminated, the input is active.
Digital output
The red LEDs are marked from DRL1 to DRL18. The attached functions appear from
the electrical diagrams. When a specific LED is illuminated, the output is active.
Communication
When the panel communicates with other panels, the LEDs flash irregularly. The red
LED indicates that the panel is transmitting information, and the green LED indicates
that information is received.
Supply
This LED flashes briefly when the power supply to the panel is switched on. During
normal operation the light is off. If the LED makes repeated flashes, it may be an
indication of a power supply error.
CPU print
The green idle LED (ACT1) flashes irregularly when the power supply to the panel is
on. A constant light or no light indicate malfunction.
The red reset LED (RST1) is normally not illuminated. The LED is only illuminated
for a brief moment when the CPU restarts the programme. This only occurs when the
power supply to the panel is switched on.
2 Commissioning of the panels
This instruction deals primarily with the initial work procedures which must be per-
formed to obtain a functional control system.
Note: Only qualified and skilled personnel are permitted to commission the pan-
els.
Prior to the initial commissioning precaution must be taken to avoid an unintentional
start of the boiler plant when the power supply to the control system is switched on.
This means that the power supply to motors, fans, pumps, etc. must be switched off.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-4 / 78 Language UK
Manually operated oil valves, which connect the oil system to the burner, should also
be closed.
Warning: The panels contain live parts making it absolutely necessary that the
service engineer complies with the safety regulations prescribed on
site. Failure to do so may cause damage to equipment and affect per-
sonal safety. Even though the power supply to the panels is switched
off, some of the terminals may still be live.
In the following sections it is assumed that the key operation lock has been unlocked
before any operation, alterations, etc. of the menu structure settings are performed.
2.1 Initial start-up
On delivery from Aalborg Industries the electrical wiring inside the control panel is
completed. This also means that the electrical wiring, power supply, and data com-
munication cable between the terminal rows of the control panels and the controllers
are connected. Even though the internal wiring has been completed, some additional
checks regarding the controllers must be carried out. These procedures, among others,
are described in the following sections.
Some of the work procedures require visual checks inside the controllers. Therefore
access to the controllers should be provided by opening the hinged door.
2.2 Connection of the external wires
Prior to commissioning the connection of the external wires must be completed on site
in accordance with the electrical diagrams. This means that wires from pump motors,
transmitters, switches, regulating valves, etc. should be connected to the terminal rows
of the control panel.
During this work the power supply for the complete boiler plant must be switched off.
Furthermore, it must be ensured that no outside voltage is applied to the digital input
connections of the control panel.
If and when functional errors of connected electrical equipment are established prior
to or during the actual commissioning of the boiler plant, the fault must be corrected.
Functional errors might be present as a result of incorrect electrical wire connections.
If this is the case, the wires should be rearranged either at the terminal rows of control
panel or at the specified electrical equipment.
2.3 Check the setting of the jumpers
2.3.1 Check the bridge connection of the terminal row
Check that the controllers are provided with a bridge connection between terminal 137
and 139.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-5 / 78
2.3.2 Check the setting of the RC jumper
The controllers are capable of operation in different modes (RC mode or non-RC
mode). This is achieved by means of the RC jumper. The jumper position that must be
applied for boiler plants can be seen in Figure 2.
2.3.3 Check the setting of the PNP/NPN jumper
When the control system should handle signals from a pick-up sensor/measuring
transducer (e.g. oil flow signals) the PNP/NPN signal jumper must be set in the correct
position. The jumper position that normally must be applied for boiler plants can be
seen in Figure 2.
2.3.4 Check the external communication plug
The external communication plug is not used for boiler plants and should therefore not
be connected.
2.4 Installation of the data communication cable
The communication between controllers is achieved through a 2-wire RS485 network.
To obtain a correct function of the data communication between the controllers, the
communication cable must be connected according to the electrical wiring diagrams.
Please see the electrical drawings for details.
As indicated in the electrical wiring diagrams, the communication cable must be con-
nected in a string line from controller to controller. This applies both for the two con-
ductors and the screening. The total length of the cable must not exceed 1,000 m.
When the data communication cable is installed, and the power supply to the controller
is switched on, the function can be checked. The communication LEDs placed inside
the controller must flash irregularly. If this is not the case, the data communication
string should be carefully examined, and the error corrected. The position of the LEDs
can be seen in Figure 2.
2.5 Connection of the power supply to the controllers
Before the power supply to the controllers is switched on, it must once again be ensured
that the boiler plant is not unintentionally started.
Step A: Check that the EPROM, EEPROM, and CPU are inserted in the CPU-print
for all included controllers.
Step B: Switch on the power supply to one of the controllers.
Step C: Check that the power LED and reset LED flash briefly when the power
supply is switched on.
Step D: Check that the idle LED and communication LEDs flash irregularly after
the power has been switched on.
Step E: Carry out the same procedures for all other included controllers.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-6 / 78 Language UK
2.6 Commissioning of the EPROM
When the control system is commissioned or the software is upgraded to a different
version number, the control system must be configured to fit the task. The items, which
must be configured to obtain an operational system, are, e.g. entering of serial number,
panel type, burner type, etc. Please note that the version number of the EPROM in all
included controllers must be identical. In the following sections the start-up procedure
is described in work steps.
2.6.1 Start-up procedure
Step A: When the electrical power to a controller is switched on, a message will be
displayed for 2-3 seconds, which indicates version number, date, time, and
company names. After this message the controller displays the menu item
line "COPY EEPROM [YES]". Please note that this menu item line only
appears if the controller already has been started before.The controller is
among other things equipped with an EEPROM, which is used to store set-
tings that deviate from the default settings provided in the EPROM (e.g.
settings for shut downs, alarms, start/stop set points, etc.). It is therefore
important to distinguish between commissioning of the plant and upgrade
of the software.When the control system is commissioned for the first time,
"NO" should be selected because the EEPROM does not contain any settings
which deviate from the default settings. If, on the other hand, the software
is upgraded, it might be advisable to select "YES". In this way all settings,
which were set at the initial commissioning or at a later point, will be main-
tained.
Step B: Press the SET soft key for a few seconds. When asked for password, press
the SET key once more (entering of super user password is not necessary).
Select "YES" or "NO" on the soft keys / and press the SET key again.
Step C: If it is intended to select "YES", this menu item can be skipped by pressing
the soft key . This is because the default setting is already "YES". In this
way the controller goes directly to the next menu.
Step D: When a selection has been made in the "COPY EEPROM" menu, press the
soft key once, and the controller displays the menu item line "SERIAL
NO.".
Step E: Press the SET soft key for a few seconds. Press the SET key once more if
password entering is necessary.
Note: Once the super user or common user passwords have been entered, they
will be active for ten seconds and one hour respectively. If at some point
the main menu has been entered, the active password time is cleared.
Step F: Enter serial number by means of the arrow soft keys. The keys / are
used to change digit position, and the keys / are used to increase or
decrease the value. The serial number is optional, but must be selected to
another value than zero. Furthermore, each of the controllers included in the
plant can contain different serial numbers.
Step G: Press the SET key when the serial number is entered.
Step H: Press the soft key once to enter the next menu.The displayed menu is the
configuration menu where panel type, burner type, burner family, baud rate,
and communication are set. The default settings must be changed to fit task.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-7 / 78
Step I: With the black bar placed on "PANEL TYPE", press the SET soft key for a
few seconds. Enter the super user password and press the SET key once
more.
Step J: Select the panel type (LOCAL 1, LOCAL 2, POWER 1, POWER 2, or EGB)
by means of the soft keys / and press the SET key again.
Step K: Move the black bar to the menu item line "BURNER TYPE" and press the
SET soft key for a few seconds. If necessary, enter the super user password
as described previously.
Step L: Select the burner type (KBSD, KBSA, MS, RMS, or KB) by means of the
soft keys / and press the SET key again. Please note that if "POWER
1", "POWER 2", or "EGB" have been selected, the burner type should be
selected as "NOT DEF".
Step M: Move the black bar to the menu item line "BURNER FAMILY" and press
the SET soft key for a few seconds. If necessary, enter the super user pass-
word as described previously.
Step N: Select burner family "MULTI" or "ALONE" by means of the soft keys /
and press the SET key again. If the plant includes two boilers, and master/
slave operation is intended, "MULTI" must be selected.
Step O: Move the black bar to the menu item line "NODE NO.OFFSET" and press
the SET soft key for a few seconds. If necessary, enter the super user pass-
word as described previously.
Step P: Select the communication channel (1-125) by means of the soft keys //
/ and press the SET key again. The node No. offset should be selected
to the same value for all included controllers in case of a single boiler plant
or a multi boiler plant with common supply systems. For a multi boiler plant
with separate supply systems the node No. offset must be divided into
groups. This means that all included controllers for the first boiler should
have the same identical number and all included controllers for the second
boiler should have another identical number.The difference in the number
value must always be minimum 12. E.g. if the node number for the first
group of controllers is 1, then the second group of controllers must be set to
1 + 12 = 13.
Step Q: Move the black bar to the menu item line "PART NO.OFFSET" and press
the SET soft key for a few seconds. If necessary, enter the super user pass-
word as described previously.
Step R: Select the partner communication channel (1-125) by means of the soft keys
/// and press the SET key again.The "node No.offset" of the partner
boiler panels in a multi boiler plant must be entered in the menu item line.
In case of a single boiler plant it is advisable also to enter the node No. offset
in this menu item line.
Step S: Move the black bar to the menu item line "BAUD RATE" and press the SET
soft key for a few seconds. If necessary, enter the super user password as
described previously.
Step T: Select the baud rate (300, 600, 1200, 2400, 4800, 9600, 19200, or 38400)
by means of the soft keys / and press the SET key again. The baud rate
should be selected to the same value for all included controllers in the plant
and as high as possible to obtain a high transmission speed.
Step U: Press the soft key once. After a few seconds the control system performs
an automatic re-start of the system. In this way the changed configuration
will be active.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-8 / 78 Language UK
2.6.2 Additional configuration
When the controller is restarted, the front menu is displayed, or if one or more shut
downs are present, the shut down list is displayed.
By means of the arrow and SET soft keys the menu items listed in the following work
steps should be checked and/or configured. The menu tree and the explanation list
found in this manual can be used to guide the operator through the system.
When the additional checks and set-up procedures are performed, the LOCAL 1 con-
troller (or LOCAL 2 controller, if provided) must be used.
Step A: Enter the menu item line "SETUP/CTRL MODE/BURNER CTRL MODE"
by means of the soft keys and check/set that the burner is in "STOPPED"
mode.
Step B: If "MULTI" was selected in the menu item line "SETUP/CONFIG/PANEL
TYPE/BURNER FAMILY", enter the menu item line "SETUP/CONFIG/
BURNER SYSTEM/MASTER-SLAVE". By means of the soft keys set the
burner operation to "MASTER or SLAVE".
Step C: Enter the menu item line "SETUP/CONFIG/BURNER OPTION" by means
of the soft keys and choose the relevant options for the boiler plant. The
actual options included in the boiler plant appear from the flow diagrams
and technical data found in the manual.
Step D: Enter the menu item line "SETUP/TIMERS/DATE/TIME" by means of the
soft keys and set the date and time.
Step E: Enter all menu items for "REMOTE CTRL" by means of the soft keys and
check/set that the remote control output is "0".
This concludes the initial start-up procedure when the EPROM is commissioned or
changed.
2.7 Additional start-up procedures
In the following section the actions which must be carried out before the boiler plant
is fully operational are briefly described.
2.7.1 Continue with the commissioning process
Before proceeding with the actual commissioning, the instructions for the boiler, burn-
er, and control system should be studied. The instructions should only be considered
as a guideline. This is due to the fact that each plant should be commissioned individ-
ually to obtain the best burner performance for the specific plant. It is therefore difficult
to give an exact commissioning procedure to follow.
Prior to and during the commissioning of the boiler plant a number of settings, timers,
parameters, etc. should be checked and adjusted to optimise the function of the plant.
Adjustments should be carried out as the optimisation requirements emerge.
By means of the menu tree, the explanation list, sequence diagram, instructions, etc.
the commissioning engineer can be guided through the system.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-9 / 78
2.7.2 Continue after exchange of EPROM
All vital parameters and settings should be checked prior to start-up of the boiler plant.
A new version of the software might contain new or moved menu items, which should
be checked and/or set before start-up.
2.8 Commissioning of the EEPROM
The EEPROM does not require any commissioning work because all settings, config-
urations, etc. are automatically stored in the EEPROM. But in plants which include
two identical boilers the commissioning work can be facilitated by copying the contents
of an EEPROM to another. The plants in question are, e.g. two MISSION OS boilers
with two stage pressure atomising burners.
Before the copy procedure is possible, a number of conditions must be fulfilled:

The boilers, burners, water level control equipment, etc. must be completely iden-
tical.

One of the boilers should be fully commissioned with regard to parameters, set-
tings, values, etc.

The serial numbers must be different.

If these requirements are fulfilled, the contents of an EEPROM can be copied as de-
scribed in the following work procedures:
Step A: Switch off the power supply to the controller on the commissioned boiler.
Step B: Remove the EEPROM. See section 3.2 for instruction regarding insertion
and removal of an EPROM.
Step C: Switch off the power supply to the controller on the boiler, which should be
commissioned, and remove the EEPROM.
Step D: Insert the EEPROM from the non-commissioned boiler into the controller
of the commissioned boiler and switch on the power supply.
Step E: If the menu item line "COPY EEPROM [YES]" appears in the display, press
the SET soft key for a few seconds. When asked for password, press the SET
key once more (entering of super user password is not necessary). Select
"NO" on the soft keys / and press the SET key again. In this way the
commissioning data, which are saved in the RAM store circuit of the con-
troller, will automatically be copied into the EEPROM.
Step F: Switch off the power supply again and remove the EEPROM from the com-
missioned boiler.
Step G: Insert the original EEPROM into the controller, which was commissioned
first, and switch on the power supply.
Step H: Insert the "copied" EEPROM into the controller of the non-commissioned
boiler and switch on the power supply.
Step I: When the menu item line "COPY EEPROM [YES]" appears in the display,
press the soft key a few times and the data of the EEPROM will be copied
into the RAM store circuit of the controller.
Step J: When the selection has been made in the "COPY EEPROM" menu, press
the soft key a few times more. The controller displays the menu item
"SERIAL NO." Entering of data in this menu item should not be performed
until later and should therefore be skipped.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-10 / 78 Language UK
Step K: Press the soft key one more time. The controller displays the menu item
"PANEL SYSTEM". If the boilers are operating as master/slave boilers, the
local panels must be set as "LOCAL 1" and "LOCAL 2" respectively. Select
"PANEL SYSTEM" and press the soft key a few times. The control sys-
tem automatically performs a restart of the system.
Step L: Change serial number as described in section 2.8.2.
In this way the EEPROM of the non-commissioned boiler will now contain the same
data as the EEPROM of the commissioned boiler. Please note that during the actual
commissioning of this boiler it might be necessary to readjust a number of settings,
timers, parameters, etc. to optimise the function of the boiler.
Note: The copying process should not be performed between a local controller
and a common controller. If this is done, e.g. copying the contents of an
EEPROM from a local controller to the EEPROM from a common con-
troller, the common controller will be configured as a local controller.
2.8.1 Change of serial number
If it is desired to operate the controllers with different serial numbers, which are re-
quired when copying an EEPROM, the numbers should be changed on one of the
boilers. This can be carried out as described in the following work procedures:
Step A: Enter the menu item line "SETUP/DIAGNOSES/SERIAL NUMBER /SE-
RIAL NO." and press the SET soft key for a few seconds. Enter password
and press the SET key once more.
Step B: Enter a new serial number by means of the soft keys /// and press
the SET key again.
Step C: Switch off the power supply to the controller and switch it on again.
Step D: When the menu item line "SERIAL NO." appears in the display, press the
SET soft key for a few seconds. Enter password and press the SET key once
more.
Step E: Enter the same serial number as before by means of the soft keys ///
and press the SET key again.
The controller is now configured with the same settings, parameters, etc. as before, but
with a new serial number.
3 Servicing of the panels
The following instruction describes the work procedures which should be carried out
in case some of the main parts of the controller are defective and must be replaced. It
is recommended that Aalborg Industries is contacted before changing any of these
parts.
Replacement of parts must be performed with the power supply to the controller
switched off. Please remember that outside control voltage may be connected. Fur-
thermore, precaution must be taken to avoid an unintentional start of the boiler plant
during servicing of the controllers.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-11 / 78
3.1 General service notes
The general service notes describe the general initiatives which must be performed
whenever parts of the controller are serviced or replaced.
In the following sections references to this section are given. Each time such a reference
appears, the service engineer should consult this section for further information.
Step A: Switch off the power supply to the controller.
Note: When replacing the battery the power supply to the controller should re-
main switched on, if possible.
Step B: Open the door and remove the transparent plate, which covers the printed
boards.
Step C: Carry out the necessary work procedures as described in the following sec-
tions.
Step D: Mount the transparent plate and door again.
Step E: Switch on the power supply to the controller.
Caution: Electronic parts can be damaged by static electricity. To avoid this,
damage precautions must be taken to discharge the static electricity
without the current passing through the electronic parts. E.g. touch
physically the part, upon which the electronic part is placed, both before
and while removing it. And touch physically the metal of the controller
cabinet, in which the electronic part should be positioned both before
and while fitting it. Naturally, the same hand must be used that holds
(or is going to hold) the electronic part.
3.2 Replacing the EPROM
The EPROM is a programmable module, placed in a socket on the CPU print, which
contains the software for the control system. When the software is upgraded (or com-
missioned) to a different version number, the control system must be configured to fit
the task. The configuration process includes setting of panel type, burner type, etc. If,
on the other hand, the EPROM is exchanged to an EPROM with the same version
number, the re-configuration procedure should not be performed. This also applies if
the EPROM has for some reason been removed from the socket holder for a period of
time.
When the EPROM is replaced, the following work procedures must be carried out:
Step A: Before the power supply is switched off, note all settings. Even though the
EEPROM stores all settings that deviate from the default settings provided
in the EPROM, it is advisable to carry out this initiative. This is due to the
fact that if an irreversible error occurs during the replacement, the data will
still be available.
Step B: See section 3.1 for disassembling instructions.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-12 / 78 Language UK
Step C: Remove the EPROM from the socket on the CPU print. The position can be
seen in Figure 2.
Note: It is of great importance that the EPROM is handled with extreme care
because it is a sophisticated electronic device. An EPROM must always be
carefully manoeuvred in and out of the socket holder due to the risk of
bending the pins on the EPROM.
Step D: Check the version number on the new EPROM. The version number appears
from the white label on the surface of the EPROM. Please note that the
version number of the EPROM must be identical in all included controllers.
Step E: Insert the new EPROM in the socket by using the fingers. Take care that all
pins on the EPROM are fitted into the socket. One of the EPROM ends is
provided with a notch. When the EPROM is inserted in the socket holder,
this notch must be in the same direction as the notch indicated on the pro-
tection plate. Please see Figure 2. If the EPROM is inserted in the reversed
direction, the display flashes when the power supply is switched on again.
Step F: See section 3.1 for assembling instructions.
Step G: Carry out the work procedures described in section 2.6 if a re-configuration
of the control system is necessary (if the software is upgraded to a different
version number).
3.3 Replacing the EEPROM
The EEPROM is a programmable module, placed in a socket on the CPU print, in
which the settings are stored that deviate from the default settings provided in the
EPROM (e.g. settings for shut downs, alarms, start/stop set points, etc.).
The panels should always be operated with the EEPROM inserted. But operation is
possible without the EEPROM inserted, and settings, configuration, etc. can be
changed and remembered even if the power supply is switched off. The data are also
stored in the RAM store circuit, which is supplied with power from the battery. When
the EEPROM is inserted in the CPU print again, these changes will automatically be
stored in the EEPROM.
If the EPROM is replaced, e.g. due to upgrading of the software, and the EEPROM is
removed, all settings set during commissioning or at a later point will be lost.
When the EEPROM is replaced, the following work procedures must be followed:
Step A: Before the power supply is switched off, note all settings. If an irreversible
error occurs during the replacement, the data will still be available.
Step B: See section 3.1 for disassembling instructions.
Step C: Remove the EEPROM from the socket on the CPU print. The position can
be seen in Figure 2. When the EEPROM is replaced, the same precautions
must be taken with regard to removal and insertion as during the replacement
of an EPROM, see section 3.2.
Step D: Insert the new EEPROM in the socket by using the fingers. Take care that
all pins on the EEPROM are fitted into the socket and that the direction is
correct.
Step E: See section 3.1 for assembling instructions.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-13 / 78
The control system is now in normal operation, and no further initiatives are necessary.
The current settings, configuration, etc. are automatically transferred and stored into
the new empty EEPROM. This also applies when changes have been made after the
old EEPROM became defective or was removed.
Note: If the serial number is changed, the controller displays the menu item line
"SERIAL NO." after power cut. The changed serial number must be en-
tered before the control system is operational again.
3.4 Replacing the CPU
If the CPU is defect or removed, the display will be out, and several of the relays switch
continuously. The following work procedures should be performed when the CPU is
replaced:
Step A: See section 3.1 for disassembling instructions.
Step B: Remove the CPU from the socket on the CPU print. The position can be
seen in Figure 2. When the CPU is replaced, the same precautions must be
taken with regard to removal and insertion as during the replacement of an
EPROM, see section 3.2.
Step C: Insert the new CPU in the socket by using the fingers. Take care that all pins
on the CPU are fitted into the socket and that the direction is correct.
Step D: See section 3.1 for assembling instructions.
3.5 Replacing the CPU print
If the CPU print, which holds the EPROM, EEPROM, and CPU (see Figure 2), must
be replaced, the following work procedures should be carried out:
Step A: Before the power supply is switched off, note all settings. If an irreversible
error occurs during the replacement, the data will still be available.
Step B: See section 3.1 for disassembling instructions.
Step C: Remove the screws by which the CPU print is fixed.
Step D: Carefully pull out the CPU print. It should be pulled out at the side in which
the connecting plugs are positioned. This is the side opposite the position of
the EPROM.
Step E: Remove the EPROM and EEPROM from the CPU print. Please see sections
3.2 and 3.3 for instructions regarding removal and insertion of the EPROM
and EEPROM.
Step F: Insert the EPROM and EEPROM in the new CPU print by using the fingers.
Take care that all pins on the EPROM and EEPROM are fitted into the
sockets and that the directions are correct.
Step G: Insert the new CPU print into the socket connections on the DI relay print
and fix it with the screws.
Step H: See section 3.1 for assembling instructions.
Step I: When the menu item line "COPY EEPROM [YES]" appears in the display,
press the soft key a few times and the data of the EEPROM will be copied
into the RAM store circuit of the local panel.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-14 / 78 Language UK
Step J: When the selection has been made in the "COPY EEPROM" menu, press
the soft key three times more. The control system displays the menu items
"SERIAL NO." and "PANEL SYSTEM" before it performs an automatic
re-start of the system. Entering of data in these menu items is not necessary
because the previously entered data are remembered. This also applies for
all other settings.
If "NO" is selected in the menu item "COPY EEPROM", the system must be re-con-
figured once again. This is also the case if a new EEPROM is inserted in connection
with the replacement of a CPU print.
3.6 Replacing the DI relay print
If the DI relay print must be replaced, the following work procedures should be carried
out:
Step A: Before the power supply is switched off, note all settings. If an irreversible
error occurs during the replacement, the data will still be available.
Step B: See section 3.1 for disassembling instructions.
Step C: Remove the CPU print, see section 3.5 for disassembling instructions.
Step D: Remove the screws by which the DI relay print is fixed.
Step E: Carefully pull out the DI relay print. It should be pulled out at the side in
which the connecting plugs are positioned.
Step F: Insert the new DI relay print into the socket connections on the relay print
and fix it with the screws.
Step G: Insert the CPU print into the socket connections on the DI relay print and
fix it with the screws.
Step H: See section 3.1 for assembling instructions.
Step I: When the menu item line "COPY EEPROM [YES]" appears in the display,
press the soft key a few times and the data of the EEPROM will be copied
into the RAM store circuit of the local panel.
Step J: When the selection has been made in the "COPY EEPROM" menu, press
the soft key three times more. The control system displays the menu items
"SERIAL NO." and "PANEL SYSTEM" before it performs an automatic
re-start of the system. Entering of data in these menu items is not necessary
because the previously entered data are remembered. This also applies for
all other settings.
If "NO" is selected in the menu item "COPY EEPROM", the system must be re-con-
figured once again. This is also the case if a new EEPROM is inserted in connection
with the replacement of a CPU print.
3.7 Replacing the relay print
When the relay print must be replaced, the following work procedures should be fol-
lowed:
Step A: Before the power supply is switched off, note all settings. If an irreversible
error occurs during the replacement, the data will still be available.
Step B: See section 3.1 for disassembling instructions.
Step C: Mark all connected wires and disconnect these from the terminal rows of
the relay print. The position of the terminal rows, relay print, etc. can be seen
in Figure 2.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-15 / 78
Warning: Some of the wires may still be live, and precautions must be taken to
secure personal safety.
Step D: Remove the screws that fix the print and tilt the print out of the plastic holders
positioned below the terminal row.
Step E: Pull the print off the guide opposite the terminal row and out of the cabinet.
Step F: Move the CPU print with the EPROM and EEPROM onto the new relay
print, see section 3.5.
Step G: Insert the new relay print into the guide and click it into position at the plastic
holders. Fix the relay print by means of the screws.
Step H: Connect all the marked wires to the terminal rows in the correct order.
Step I: See section 3.1 for assembling instructions.
If the menu item line "COPY EEPROM [YES]" appears in the display when the control
system is restarted, perform the same work procedures as described in section 3.5.
3.8 Replacing an exchangeable relay
The digital output DRL1 to DRL4 are equipped with exchangeable relays. This is
because the actions that are controlled by these output signals cause an increased num-
ber of relay changes which increases the risk of wearing down these relays.
The following work procedures should be performed when an exchangeable relay is
replaced:
Step A: See section 3.1 for disassembling instructions.
Step B: Push the black plastic clamp, which holds the relay to the side.
Step C: Pull up the relay and replace it. The relay must be inserted correctly, see the
connections on the relay bottom plate and the legs on the relay. Be careful
not to bend the legs on the relay.
Step D: Push back the clamp over the relay.
Step E: See section 3.1 for assembling instructions.
3.9 Replacing the display
If the display must be replaced, the following work procedures should be carried out:
Step A: See section 3.1 for disassembling instructions.
Step B: Disconnect the connection plug for the display on the connection socket of
the relay print. The position can be seen in Figure 2.
Step C: Unscrew the two nuts that fix the top display print and carefully pull it out.
The two power supply wires to the bottom display print should also be dis-
connected.
Step D: Unscrew the four nuts that fix the display protection plate and bottom display
print, which includes the display.
Step E: Replace the defective part (top display print, bottom display print, or both).
Step F: Assemble the bottom display print, display protection plate, and top display
print by means of the nuts and distance pieces. When assembled, the nuts
must not be fastened too mush or else several horizontal lines may appear
in the display.
COMMISSIONING AND SERVICE OM9306_59#A.2
23-16 / 78 Language UK
Step G: Connect the two power supply wires between the prints and the connection
plug for the display into the connection socket of the relay print.
Step H: See section 3.1 for assembling instructions.
3.10 Replacing the soft keys
If the soft keys must be replaced, the following work procedures should be followed:
Step A: See section 3.1 for disassembling instructions.
Step B: Disconnect the connection plug for the soft keys on the connection socket
of the relay print. The position can be seen in Figure 2.
Step C: Carefully remove the plastic cover that covers the soft key section.
Step D: Replace the soft key section.
Step E: Carefully mount the plastic cover again using silicone for sealing.
Step F: See section 3.1 for assembling instructions.
3.11 Replacing the door on power panels
If the door of a power panel must be replaced, the following work procedures should
be performed:
Step A: See section 3.1 for disassembling instructions.
Step B: Disconnect the two connection plugs for the display and soft keys on the
connection sockets of the relay print. The positions can be seen in Fig-
ure 2.
Step C: Remove the two fuse straps as well as the earth connections and remove the
defective door.
Step D: Mount the two fuse straps and connect the earth connections between the
door and the panel cabinet.
Step E: Connect the connection plugs for the display and soft keys on the new door
to the connection sockets on the relay print.
Step F: See section 3.1 for assembling instructions.
3.12 Replacing the circuit fuse
If the circuit fuse has blown, the four line crystal display will be off. A new circuit fuse
with the specifications 3.15T/250 V, 5 x 20 glass should be inserted.
The following work procedures should be carried out when the circuit fuse is replaced:
Step A: See section 3.1 for disassembling instructions.
Step B: Screw out the top of the fuse holder and replace the circuit fuse. The location
of the circuit fuse can be seen in Figure 2.
Step C: Screw in the top of the fuse holder with the circuit fuse.
Step D: See section 3.1 for assembling instructions.
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-17 / 78
3.13 Replacing the battery
The battery is primarily used to ensure that the internal watch runs accurately after
power cut. This is done by supplying the RAM-stores during power cuts.
The battery is of the Lithium type (size AA) and has an expected life up to five years,
depending on the actual conditions such as humidity, ambient temperature, etc. Please
note that it is not reloaded by the electronic circuit in the controller.
If the menu item line "COPY EEPROM [YES]" appears in the display after power cut,
the battery should most likely be replaced.
The following work procedures should be followed when the battery is replaced:
Step A: See section 3.1 for disassembling instructions.
Step B: Cut off the cable binders, which hold the battery. The location of the battery
can be seen in Figure 2.
Step C: Disconnect the battery wires and replace the battery.
Note: Disposal of the old battery should be in accordance with the environmental
rules in force.
Step D: Use two new cable binders to fix the new battery in its correct place.
Step E: See section 3.1 for assembling instructions.
Step F: If the menu item line "COPY EEPROM [YES]" appears in the display, press
the soft key a few times and the data of the EEPROM will be copied into
the RAM store circuit of the controller.
Step G: When the selection has been made in the "COPY EEPROM" menu, press
the soft key a few times. The control system displays the menu items
"SERIAL NO." and "PANEL SYSTEM" before it performs an automatic
re-start of the system. Entering of data in these menu items is not necessary
because the previously entered data are remembered. This also applies for
all other settings.
The controller is now ready for normal operation. If a new battery is not available,
"YES" must be selected in the menu item line "COPY EEPROM" every time the panel
is started.
3.14 Replacing the data communication cable
If the communication cable is damaged, it must be replaced. The installation and com-
missioning work should be performed as described in section 2.4. When the cable is
replaced at one of the controllers, the screen must be connected correctly in the screwed
joint as shown in Figure 3.
The new cable must be of the same type as the original cable delivered by Aalborg
Industries and as a minimum have the following data:
COMMISSIONING AND SERVICE OM9306_59#A.2
23-18 / 78 Language UK

Cable type: 2-conductor data cable with screening

Loop resistance: 74 /min.

Insulation resistance, minimum: 100 M-km

Pair capacity: 85 pF/m

Finishing of the cable screening in a screwed joint
1.
2.
3.
4.
5.
Panel cabinet
Figure 3 om9306_59_unisabx0063060en.wmf
COMMISSIONING AND SERVICE OM9306_59#A.2
Language UK 23-19 / 78
Monitoring and control via touch screen
1 General
This section describes the mimic pictures, dialog boxes, lists, etc. for a standard mon-
itoring and control system. In the example pictures is shown a generic boiler with a
KBP burner and an EGBexhaustgas boiler. The illustrations and descriptions do not
show the completetouch screen system, but gives an insight into the system concept.
Notice also that the pictures show a maximum configuration meaning that e.g. inert
gas is shown. On the real system this will not be present if the system is not configured
for inert gas.
The touch screen is connected to the boiler control panels via a RS485 communication
network. By means of this connection the touch screen monitoring and control system
can receive, handle, and transmit data to and from the control panels. This enables
control of the boiler plant from the touch screen. The mimic pictures and lists are used
to monitor the boiler plant and the dialog windows are used to control and operate the
boiler plant.
Notice that it is still necessary to configure the basic settings such as burner type on
the local controller.
2 Operation of the touch screen system
When the touch screen is switched on, it will automatically start the monitoring and
control program after a short initialisation period. Figure 1 illustrates the start-up mimic
picture.
From the main picture, it is possible to acknowledge alarms have access to the different
subsystems of the plant: Steam (and exhaust gas boiler), water, fuel, and burner system
as well as an overview picture called boiler. In the main window the key can also be
retrieved, trend curves for the performance of the plant can be viewed and the set-up
menu can be accessed. A detailed description of the different menus is given in the
following. The subsystem pictures steam, water, fuel, burner and boiler as well as the
main- and alarm pictures areall accessible from each subsystem picture.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-20 / 78 Language UK
Start-up picture on the touch screen
Figure 1 om9306_56_pic_0x0062400en.wmf
The key in the upper left corner shows that the system is unlocked allowing parameter
changes from the touch screen.How to retrieve and release the key lock can be seen in
the document Key Operation Lock.
2.1 Contact information
From the main picture access is given to contact information on Aalborg
Industries A/S by clicking the logo as illustrated in Figure 2.
Access to contact information
Figure 2 contouch_15bx0200170en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-21 / 78
Contact information picture
Figure 3 contouch_16x0197880en.wmf
From the picture containing contact information access is given to the main menu by
clicking the arrow in the lower left corner (Figure 3).
2.2 Alarm menu
The [ALARM] button (Figure 4) placed in the upper right corner of the screen is
accessible from any of the submenus, which ensures full access to acknowledging
alarms independent of which picture is present on the screen.
Allarm button
Figure 4 contouch_17ax0200180en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-22 / 78 Language UK
The [ALARM] button gives access to the alarm list (Figure 5)
Sub menu: Alarm list
Figure 5 om9306_56_alarmx0062290en.wmf
[ESC] Escape button. Return to the previous menu.
[] Scroll up in the alarm list.
[] Acknowledge an alarm.
[ ] Enlarge text (cycles through sizes)
[ ] See timestamp and other information for the alarms.
[] Scroll down the alarm list.
2.3 Steam system menu
The steam system menu gives access to an overview of the steam system including
steam dump and inert gas status, modifying parameters and accessing the exhaustgas
boiler menuif such is part of the system. The structure of the steam menu is illustrated
in Figure 6
Menu structure for the steam menu

Main Steam
Parameters
Exhaustgas
boiler
Feed water/circulation
pump control
Figure 6 contouch_19x0197910en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-23 / 78
The steam system menu is entered from the main menu by clicking the [STEAM]
button (Figure 7).
Steam system menu
Figure 7 contouch_20bx0200190en.wmf
The picture under the steam menu is an overview of the steam system (Figure 8).
Steam system overview
Figure 8 om9306_56_pic_50x0062680en.wmf
In the steam overview picture, the actual values for boiler pressure, water level, and
load can be seen as well as the state of the steam dump valve and inert gas. Parameters
for the steam system are set under the [PARAM] button in the lower right corner and
in the middle left access is given to the exhaust gas boiler picture if configured.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-24 / 78 Language UK
2.3.1 Parameters for the steam menu
From the steam menu there is access to the parameters submenu by clicking the [PAR-
AM] button in the lower right corner of the steam menu (see Figure 9)
Entering parameter sub menu for the steam menu
Figure 9 contouch_22x0197940en.wmf
In the parameter sub menu (illustrated in Figure 10) the actual set point for the steam
dump is monitored as well as the process value and the regulator output. The set point
can be changed by pushing Set point button (dark grey). From the parameter submenu
there is also access to the inert gas menu, the main menu, the steam menu (arrow), and
the regulator parameters
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-25 / 78
Parameter sub menu under the steam menu
Figure 10 om9306_56_pic_52x0062690en.wmf
Regulator parameters
The regulator sub menu (see Figure 11) gives access to monitoring and changing of
the regulation parameters: sampling time, proportional gain, integral time, and the
derivative time. Furthermore, the control mode of the valve can be monitored and
changed between auto and manual. If the valve is controlled manually, the position
can be set under the Manual position set-point as a percentage of full open. 0.0 % is
closed valve, and 100.0 % is a fully open valve. From this sub menu it is possible to
return to the parameter submenu (Arrow) or the main menu.
Regulator parameteres under the steam dump sub menu
Figure 11 om9306_56_pic_53x0062700en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-26 / 78 Language UK
Inert Gas sub menu
From the parameters sub menu there is access to the inert gas menu by pushing the
button [Inert gas] (Figure 12)
Parameters submenu under the steam menu
Figure 12 contouch_25x0197970en.wmf
In the inert gas menu (Figure 13 ) the load and forced load can be monitored.
Inert gas menu
Figure 13 om9306_56_pic_54x0062710en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-27 / 78
From the Inert gas menu there is access to the main menu, the steam dump parame-
tersusing the [steam dump] button, and the steam menu, when pushing the arrow in
the lower left corner.
2.3.2 Exhaust gas boiler picture
If an exhaust gas boiler is chosen, the Steam overview picture will show an EGE or
EGB button (Figure 14 shows an EGB button) depending on if and what exhaust gas
boiler is configured (done on the controller in the panel).
Exhaust gas boiler button
Figure 14 contouch_27x0197990en.wmf
Pressing the button brings the user to the exhaust gas menu (see Figure 15).
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-28 / 78 Language UK
Exhaust gas boiler menu
Figure 15 om9306_56_pic_80x0062760en.wmf
In Figure 15 both circulation pumps are stopped. Manual control of the pumps can be
done by clicking the pump. Notice the * besides the pump. * marks that the icon (pump)
is a button.
2.3.3 Circulation/EGB feedwaterpumps
Depending on the boiler type chosen the exhaust gas water pumps are called circulation
pumps (EGE) or EGB feed water pumps (EGB). In the following they will just be
referred to as EGB feed water pumps.
Changing the state of these pumps is done by clicking the pump button (Figure 16).
Accessing EGB feed water pumps sub menu
Figure 16 om9306_56_pic_80x0062760en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-29 / 78
The dialog window for the circulation pump is illustrated inFigure 17. In this dialog
box, the mode of the pump (start, stop, and stand by) can be set by pushing the buttons.
The status of the pump is seen under status. If any alarms were present, they would be
marked in the Alarms section of the window. It will be marked if the alarm is due
to no feedback or overload (Circulation pumps also have a low flow alarm).
Dialog window for an EGB feed water pumps
Figure 17 om9306_56_pic_87x0062770en.wmf
From the pump dialog, it is possible to navigate back to the exhaust gas boiler picture
by pushing the arrow in the lower left corner, to the main menu by pushing the [MAIN]
button in the upper left corner or to go to the next pump on the exhaustgas boiler (if
available) by pressing the arrow in the lower right corner of the picture.
2.4 Water Menu
The water menu gives access to an overview of the feed water system and to change
the parameters of the system. The structure of the feed water menu is illustrated in
Figure 18
Menu structure for the water menu

Main Water
Chemical dosing
Parameters
Feed water pumps
Figure 18 contouch_31x0198030en.wmf
The water menu is entered from the main menu (Figure 19) or from any of the other
overview pictures.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-30 / 78 Language UK
Water menu access
Figure 19 contouch_32ax0198790en.bmp
The mimic picture of the water menu gives an overview of the feed water system
(Figure 20).
Feed water system overview
Figure 20 om9306_56_pic_40x0062600en.wmf
At the feed water overview, the steam pressure, water level and load of the system can
be monitored. Furthermore, the status of the feed water valve is seen as a percentage
of open, in this example (Figure 20) the valve is closed. A measurement of the salinity
is also visible as well as it is possible to see if the pumps are running or stopped. In
Figure 20 the two circulation pumps from the hot well are running and the chemical
dosing pump is stopped.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-31 / 78
From the feed water menu there is access to monitoring and control of the different
pumps by pushing them and also parameters for the feed water system can be set under
the [PARAM] button in the lower right corner.
2.4.1 Feedwater Pump
Control and monitoring of the feedwater pumps can be done by clicking the pump as
illustrated in Figure 21.
Access to circulation pump
Figure 21 contouch_34x0198060en.wmf
The dialog window for the feedwater pump is illustrated in Figure 22
Dialog window for a circulation pump
Figure 22 om9306_56_pic_47x0062650en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-32 / 78 Language UK
As seen in the figure the pump control resembles the control described in Section 2.3.3.
From the dialog window of a water pump there is access to the main menu or the
overview of the feed water system by clicking the button in the lower left corner.
2.4.2 Parameters
Under the submenu parameters access is given to alarm settings, water level settings
etc. The submenu is entered from the feed water overview picture (Figure 23)
Access to the parameter submenu
Figure 23 contouch_36x0198080en.wmf
The parameter submenu under the feed water system gives access to the water alarm
limits as illustrated in Figure 24. The shut-down limit and the alarm limits for salinity
can be monitored and changed.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-33 / 78
Parameter submenu
Figure 24 om9306_56_pic_41x0062610en.wmf
From the water alarm limits access is given to water level regulation parameters,to
feedwater ON/OFF regulation parameters, to the main menu, and to the water system
overview
Water level regulation
Access to the regulation and monitoring of the water level is done by clicking the button
on the left side of the picture (Figure 25).
Access to water level regulation
Figure 25 contouch_38x0198100en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-34 / 78 Language UK
The water level regulation and monitoring is carried out from the mimic picture illus-
trated in Figure 26. In the upper part of the level regulation dialog window the actual
values are monitored, i.e. the actual set point, the actual value, and the regulator output.
The set point and the process value are measured in mm from normal water level, where
a minus indicates that the water level is below normal water level, and no sign in front
of the figure means above normal water level. The lower part of the dialog window is
for changing the values of the set points and the normal/stand-by limits.
Water level regulation dialog window
Figure 26 om9306_56_pic_42x0062620en.wmf
From the water level regulation dialog window, there is access to the Salinity limits,
the ON/OFF regulation menu and it is possible to go to the main menu and well as
return to the overview of the feed water system (the buttons in the lower left of Fig-
ure 26). Furthermore, access is given to the regulator parameters.
Regulator Parameter
Access to the feed water regulator parameters is given from the water level menu as
illustrated in Figure 27.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-35 / 78
Access to feed water regulation parameters
Figure 27 contouch_40x0198120en.wmf
The regulator parameters, which can be set is illustrated in Figure 28 and they are listed
and described below.
Feed water regulation parameters
Figure 28 om9306_56_pic_43x0062630en.wmf
Feed water level regulator parameters, which can be set:
[Neutral zone] The maximum deviation from the set point, which is accepted without
any regulation, takes place.
[I low limit] The lowest acceptable water level.
[I high limit] The highest acceptable water level.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-36 / 78 Language UK
[Sampling time] The time between two samples.
[Proportional Gain] Regulator parameter
[Integral time] Regulator parameter
[Derivative time] Regulator parameter
[Valve control mode] For setting the valve in automatic or manual mode.
[Manual pos. set point] If the valve is set to be in manual mode, the position can here
be set as a percentage of fully open.
From the feed water level regulation dialog window, access is given back to the main
menu and the feed water overview (lower left arrow).
Feedwater ON/OFF regulation
The last menu point in the feed water menu is the feedwater ON/OFF regulation menu
accessible via the button with the same name on the left of the menu (see Figure 29).
Access to feed water ON/OFF regulation
Figure 29 contouch_42x0198140en.wmf
The menu simply shows the status of the pumps (see Figure 30) to be used when running
an ON/OFF feedwater regulation.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-37 / 78
Feed water ON/OFF regulation dialog window
Figure 30 om9306_56_pic_44x0062640en.wmf
From the feedwater ON/OFF regulation dialog window, there is access to the Salinity
limits and the Level regulation menu. It is also possible to go to the main menu and
well as return to the overview of the feed water system (the buttons in the lower left
of Figure 30).
2.5 Fuel menu
From the fuel menu access is given to an overview of the fuel system and control of
the pumps in the system. The structure of the fuel menu is illustrated inFigure 31
Menu structure for the fuel meny

Main Fuel
Parameters
Fuel oil pumps
Figure 31 contouch_44x0198160en.wmf
The fuel menu is entered from the main menu as illustrated in Figure 32 or any of the
other system menus.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-38 / 78 Language UK
Access to the fuel menu
Figure 32 contouch_45ax0198800en.bmp
The picture under the fuel menu is an overview of the fuel system, which is illustrated
in Figure 33.
Fuel oil system overview
Figure 33 om9306_56_pic_30x0062580en.wmf
On the overview of the fuel oil system access is given to the fuel oil pumps and pa-
rameters to be set in the fuel oil system. Furthermore, fuel oil temperature and pressure
can be monitored if available. It is also possible to see if the system is running HFO
or diesel and what type of oil heater is configured. If the heater is electric the status of
the element is indicated with a green bar meaning on. If the heater is a steam heater
the temperature of the steam used to heat the fuel oil is displayed.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-39 / 78
2.5.1 Fuel oil pumps
From the fuel oil system overview, access is given to the fuel oil pumps by clicking
the pumps as illustrated in Figure 34.
Access to fuel oil pump
Figure 34 contouch_47x0198190en.wmf
As seen in Figure 35 the pump control resembles the control described in Section 2.3.3.
Fuel oil pump dialog window
Figure 35 om9306_56_pic_37x0062590en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-40 / 78 Language UK
From the dialog window of a fuel oil pump there is access to the main menu or the
overview of the fuel oil system by clicking the button in the lower left corner. By
pressing the arrow in the lower right corner the picture switches to the next fuel oil
pump.
2.5.2 Parameters for the fuel oil system
Access to the parameter settings of the fuel oil system is given by clicking the [PAR-
AM] button in the lower left corner as illustrated in Figure 36
Acess to the fuel oil system parameters
Figure 36 contouch_49x0198210en.wmf
The dialog window for the parameter settings for the fuel oil system is illustrated in
Figure 37. Notice that the illustration is for a KBP burner as mentioned in the intro-
duction. For some burners (e.g. RMS) the preheater is placed on the burner picture for
better correspondence with the actual burner design. Placement for menus relevant for
the preheater will therefore move as well.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-41 / 78
Parameters / Pressure alarm limits for the fuel oil system
Figure 37 om9306_56_hc_003x0062330en.wmf
Fuel oil pressurelimits menu
The top menu available (Figure 37) is the Pressurelimits list. The list holds the alarm
limits concerning fuel oil pressure.Notice that if a pressure measurement is not avail-
able on the burner (e.g. on MS), the common oil pressure on the common controller is
used.
The high shutdown alarm limit, low alarm limit, and the low shut-down limit can be
set by pressing the dark grey button after each point in the list.
From the menu there is access to the main menu or the overview of the fuel oil system
by clicking the button in the lower left corner. Accessis also available to the other menu
points: Oil temp. limits, Oil Temp reg. and burner limits.
Fuel Oil Temperature limits menu
The menu oil temp. limits holds alarm limits concerning fuel oil temperatures (see
Figure 38 ). Notice that this temperature is measured in the preheater.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-42 / 78 Language UK
Temperature alarm limits for the fuel oil system
Figure 38 om9306_56_hc_006x0062350en.wmf
The high and low shutdown as well as the low alarm limit can be set by pressing the
dark grey button after each point in the list.
From the menu there is access to the main menu or the overview of the fuel oil system
by clicking the button in the lower left corner. Access is also available to the other
menu points: Pressure limits, Oil Temp reg. and burner limits.
Temperature regulator menu
In the Oil temp reg. menu (see Figure 39) the regulation set points are displayed in the
top.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-43 / 78
Fuel oil temperature regulation
Figure 39 om9306_56_hc_007x0062360en.wmf
Notice that KBP has two set points: One for standby and one for firing. If a steam
heater is chosen (as it is the case in Figure 39) the menu also displays control buttons
used for controlling the steam valve in the heater. The actuator can be set in manual
mode allowing manual control of its position by pressing the up arrow for increasing
the opening degree of the valve or down arrow for decreasing the degree. By pressing
the Regulator set points button in the bottom of the picture it is possible to configure
the regulator parameters. The parameters that can be set for a steam heater is illustrated
in Figure 40 and described in the list below.
Fuel oil temperature regulation parameters
Figure 40 om9306_56_hc_009x0062370en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-44 / 78 Language UK
Fuel oil temperature regulator parameters, which can be set:
[Neutral zone] A band around the set point where regulation is not carried out (the
process value error is ignored).
[Gain] Regulator parameter Proportional gain
[Sampling time] The time between two samples.
[Integral time] Regulator parameter
[Difference time] Regulator parameter
[Minimum pulse] The minimum time the preheater can be on in each PWM period.
[Run time] Time for one PWM period.
From the parameters menu access is given either back to the temperature regulation
menu using the arrow in the lower left corner or to the main menu using the top left
button. Back in the Temperature regulation menu there is access to the main menu or
the overview of the fuel oil system (button in the lower left corner). Access is also
available to the other menu points: Pressure limits, Oil Temp. limits and burner limits.
Burner limits menu
Some of the burners are equipped with an additional temperature measurement on the
burner. Alarms concerning this measurement can be set under the last menu the
Burner limits menu illustrated in Figure 41.
Acess to preheater limits menu
Figure 41 om9306_56_hc_010x0062380en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-45 / 78
The menu holds a high and low shutdown value that can be modified through the dark
grey indicators.From the Burner limits menu, access is given back to the main menu
and the fuel oil overview (lower left arrow). Access is also available to the three other
menu points: Pressure limits, Oil Temp. limits and Oil temp. reg.
2.6 Burner Menu
The burner menu gives access to an overview of the burner system and to alarm settings
of the system. The structure of the burner menu is illustrated in Figure 42
Menu structure for the burner menu
Main Burner Parameters Main Burner Parameters
Figure 42 contouch_55bx0201950en.wmf
Access to the burner menu is given from the main picture (Figure 43) or from any of
the other system menus.
Access to the burner menu
Figure 43 contouch_56ax0198810en.bmp
The overview of the burner system is illustrated in Figure 44
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-46 / 78 Language UK
Burner system overview
Figure 44 om9306_56_pic_20x0062490en.wmf
In the overview picture a simplified diagram of the burner system is shown. On the
left side is the pressure, water level and boiler load. On the right side the main burner
components, that are important for illustrating the system state, are shown:

Position of the fuel valve and air damperdamper.State is shown as a percentage

of fully open. If actuators are mechanically connected only the fuel valve are
shown.

Fuel oil flow(percentage of full load). If available.

Uptake temperature.If available.

State of the main valves. State is shown with green meaning activated and grey
meaning deactivated.

State of the main switches.E.g. the combustion air pressure switch indicating if
pressure is high enough. If the switch is in an error state the switch symbol is red
(illustrated in Figure 44).

State of burner system motorsThe state of the burner motor and, if separate as
in rotary cup burners, the combustion air fan motor is also monitored. Figure 44
shows a KBP burner with a burner motor. The yellow cross means that the
burner is stopped. A green rotation symbol:indicates that the motor is running.
Nothing can be activated directly from the burner picture. If burner parameters has to
be modified, this must instead be carried out in the parameter menu.
2.6.1 Parameter settings
The parameter settings or alarm limit settings related to the burner system is accessed
from the burner overview picture by clicking the [PARAM] button (Figure 45).
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-47 / 78
Acess to the parameter settings in the burner system
Figure 45 contouch_58x0198300en.wmf
The first menu displayed is the Uptake limits menu. Here limits can be set for the high
alarm and the high shut-down uptake temperature (see Figure 46).Notice that the il-
lustration is for a KBP burner as mentioned earlier. For some burners (e.g. RMS) the
preheater is placed on the burner picture for better correspondence with the actual
burner design. Placement for menus relevant for the preheater will therefore move as
well.
Uptake limits list for burner system
Figure 46 om9306_56_pic_21x0062510en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-48 / 78 Language UK
From the uptake limits menu, access is given to the main menu and back to the burner
overview (lower left arrow). Figure 46 also shows another menu choice the Servo
valves menu. If the system was configured with a burner that had a windbox another
menu choice would be possible as well the windbox limits menu.
Windbox limits
The windbox limits menu is available on burners that is configurated with such and
can be accessed by pressing the windbox limits button on the left side of the screen
(Figure 47shows the parameter menu on KBE burner).
Access to th windbox limits menu
Figure 47 contouch_60x0198320en.wmf
The windbox limits menu actually just holds one limit the temperature high limit
used to determine a threshold for the fire in windbox shutdown (see Figure 48).
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-49 / 78
Windbox limits list for the burner system
Figure 48 om9306_56_pic_22x0062530en.wmf
The last menu available is the servo valves menu.
Servo valves
The servo valve control menu is available by pressing the servo button on the left side
of the screen see Figure 49
Access to the servo valve control menu
Figure 49 contouch_62x0198340en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-50 / 78 Language UK
The servo valves menu allows for manual or automatic control of the oil (valve) and
air (damper) servos as well as setting different parameters relevant to this. The menu
is illustrated in Figure 50.
The servo valve control menu
Figure 50 om9306_56_pic_29x0062570en.wmf
In the menu the air damper and oil valve position can be monitored. The actuators can
be set in manual mode allowing manual control of their position by either entering the
position (as a percentage of full open) in the setpoint (dark grey) box or by pressing
the arrows. For each servo it is possible to configure the regulators behind their auto-
matic functioning. This is done by pressing the servo reg. param. button below the
servo that is to be changed (See Figure 51).
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-51 / 78
Access to the servo valve settings
Figure 51 contouch_64x0198360en.wmf
The servo reg. param. menu allows the user to change to regulator parameters. The
menu for the air servo is displayed in Figure 52.
Servo control to air damper
Figure 52 om9306_56_hc_005x0062340en.wmf
Parameters which can be set are:
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-52 / 78 Language UK
Position neutral zone: The accepted distance from the actual position to the set point
position.
Sampling time: The time between two samples.
Proportional Gain: Regulator parameter
Integral time: Regulator parameter
Derivative time: Regulator parameter
Minimum pulse: The minimum on time that the servo relay can be activated.
Run time: A parameter indicating the time period in which the regulator operates. This
is not the same as the period the actuator is active but it affects this.
From the servo control menu access is given to the main menu, alarm limit list and
back to the parameter menu (arrow in lower left corner).
2.7 Boiler Menu
The boiler menu gives access to an overview of the entire boiler system and alarm
limits can be set. Manual control of the load can be taken. The menu structure of the
boiler menu is illustrated inFigure 53.
Menu structure of the boiler menu

Main Boiler Parameters
Figure 53 contouch_66x0198380en.wmf
Access to the boiler menu is given from the main picture as illustrated in Figure 54.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-53 / 78
Access to the boiler menu
Figure 54 contouch_67ax0198820en.bmp
In the boiler overview picture the boiler pressure, water level, and the load of the boiler
can be monitored in the middle of the picture. Also oxygen level and the smoke density
can be monitored as illustrated in Figure 55.
Boiler menu overview
Figure 55 om9306_56_pic_10x0062420en.wmf
2.7.1 Parameter settings for the boiler system
From the boiler overview picture access is given to parameter settings of the boiler
settings as illustrated in Figure 56.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-54 / 78 Language UK
Access to the parameter settings for the boiler menu
Figure 56 contouch_69x0198410en.wmf
The alarm limits list is divided into two sections. In the upper section the alarm limits
concerning water level are placed, and in the lower section, the alarm limits concerning
the boiler pressure are placed.
The alarm limits, which can be changed,are for the water level: High and low shut-
down limits, and high and low alarm limits. For the boiler pressure high and low alarm
limits, and the high shut-down limit can be set.
Parameters / alarm limits for the boiler system
Figure 57 om9306_56_pic_11x0062430en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-55 / 78
From the alarm list, access is given to parameter settings for pressure regulation, smoke
density alarms, oxygen limits and load control in the left side of the picture.
Access to the pressure regulation dialog window is achieved by pressing the pressure
regulation button on the left (see Figure 58).
Access to pressure regulation parameters
Figure 58 contouch_71x0198430en.wmf
The pressure regulation dialog window(see Figure 59) is divided into two sections.
The upper section is a monitoring section and the lower section is a control section,
where the parameters can be set. The values, which can be monitored,are the current
set point, pressure and regulator output. The parameters, which can be set, are the
normal set point and the high set point.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-56 / 78 Language UK
Pressure regulating dialog box
Figure 59 om9306_56_pic_12x0062440en.wmf
From the pressure regulation dialog window access is given to the regulator parameters
as illustrated in Figure 60.
Pressure refulation dialog box
Figure 60 contouch_73x0198450en.wmf
The regulator parameters for the boiler pressure regulation (Figure 61), which can be
changed, are:
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-57 / 78
Sampling time: The time between two samples.
Proportional Gain: Regulator parameter
Integral time: Regulator parameter
Derivative time: Regulator parameter
Set point: The desired temperature.
Mode: For setting the valve in automatic or manual mode.
Regulator parameters for pressure regulation
Figure 61 om9306_56_pic_13x0062460en.wmf
From the pressure regulation parameters access is given to the main menu and back to
the pressure regulation (arrow in lower left corner).
Smoke Density
Access is given to the smoke density menu from the boiler system parameter menu as
illustrated in Figure 62 or from the other sub dialog windows under the boiler system
parameter list.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-58 / 78 Language UK
Access to the smoke density menu
Figure 62 contouch_75x0198470en.wmf
In the smoke density menu, the high alarm limit can be set as a percentage (see Fig-
ure 63). The menu also allows operation of the smoke density blower. By switching
the lowest dark grey button from OFF to ON the smoke density blower is started.
Smoke density menu
Figure 63 om9306_56_hc_002x0062320en.wmf
From the smoke density alarm list access is given to the main menu, the alarm limit
dialog windows under the boiler alarm list in the left side of the picture.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-59 / 78
Load control
Access to manual load control of the boiler is also available from the parameter menu
or from the sub dialog windows (illustrated in Figure 64).
Access to manual load control
Figure 64 contouch_77x0198490en.wmf
The manual load control dialog window (Figure 65) is not only for monitoring and
controlling the load. It is also to be used as a general purpose inspection screen.
The actual load of the boiler can be monitored in the bar in the left part of the window.
The load is displayed using a bar graph showing load as a percentage of the full load.
For precise read out the load value is also displayed numerically in the middle of the
bar. The state of the boiler is seen in the middle of the screen. The state can be set to
either stopped (as on Figure 65), automatic or manual.If in manual mode the burner
can be started and stopped and the load increased and decreased using the respective
buttons.In the top of the picture is the current boiler pressure to help when controlling
the load manually. In the bottomright is the set point choice for easy changing of set
points especially when running in automatic mode. To the left of this is the total oil
consumption value for easy readout of this common task.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-60 / 78 Language UK
Manual load control dialog window
Figure 65 om9306_56_pic_17x0062480en.wmf
Notice that the burner must be in modulation free mode before the load can be con-
trolled.
2.8 Trend
From the main menu access is given to trend curves for selected parameters of the
plant. Access to the trend information is illustrated in Figure 66.
Access to the trend menu
Figure 66 contouch_79ax0198830en.bmp
The trend menu is illustrated in Figure 67. From this dialog window access is given to
trends of different plant variables, e.g. boiler pressure, load, fuel pressure, etc. A trend
curve for each of these variables is accessible by clicking the variable button on the
dialog window. A trend exampleis shown in Figure 68.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-61 / 78
Plant view for trend curves
Figure 67 om9306_56_pic_50x0062660en.wmf
Example of trend curve
Figure 68 om9306_56_trendx0062780en.wmf
There are several ways of controlling how the trend curve is displayed.
The vertical scaling (value) can be adjusted by setting the max and min value in the
lower right corner.
To adjust the horizontal axis (time / history) simply press anywhere on the graph to
bring up the history control buttons (see Figure 69).
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-62 / 78 Language UK
Activating history control
Figure 69 contouch_82x0198540en.wmf
The buttons function as follows:
[<<] Large jump back in measurement history
[<] Jump back in measurement history
[-] Zoom in / decrease shown time span.
[^] Reset view
[+] Zoom out / increase shown time span.
[>] Jump forward in measurement history
[>>] Large jump forward in measurement history
2.9 Set-up
The set-up menu gives access to set timers, alarm limits, diagnostics, configuration of
the displayed system, etc. The structure of the set-up menu is illustrated in Figure 70
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-63 / 78
Menu structure of the set up menu
Main Set-up Set-up
Program Version
Program Layout
Display Layout
Plant Settings
Log-Out
Digital Input
Digital Input
Oil Summarizer
Hour Counters
Plant Settings
Timer Settings
Main Set-up Set-up
Program Version Program Version
Program Layout Program Layout
Display Layout Display Layout
Plant Settings Plant Settings
Log-Out Log-Out
Digital Input
Digital Input
Oil Summarizer
Hour Counters
Plant Settings
Timer Settings
Figure 70 contouch_83ax0200230en.wmf
Access to the set-up menu is given from the main picture as illustrated in Figure 71
Access to set-up menu
Figure 71 contouch_84ax0198840en.bmp
The set-up menu gives access to set-up of timers, counters, plant limits, diagnostic
digital input, diagnostic digital output, and configuration of the display layout.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-64 / 78 Language UK
2.9.1 System
Under system setup information is given on the type of the panel and the burner. The
system clock and date can be monitored and set as illustrated in Figure 72.
System set-up dialog window
Figure 72 om9306_56_pic_60x0062720en.wmf
Diagnostic information on digital inputs and outputs
From the system dialog window access is given to the diagnostic information on the
digital inputs and outputs in the lower right corner as illustrated in Figure 73.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-65 / 78
Access to diagnostic information on in- and outputs
Figure 73 contouch_86x0198580en.wmf
An example of on of the dialog windows with the digital inputs are illustrated in
Figure 74. The status of each input is seen in the box next to the line (Green marks
ON/Activated).
Diagnostic-digital input example
Figure 74 om9306_56_pic_22x0062540en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-66 / 78 Language UK
By pressing the arrow on the lower right corner of the picture the next window with
digital inputs are presented.
Diagnostic Digital Output
The digital outputs can also be checked for diagnostic purposes. These pictures have
the same functionality as the inputs. Figure 75shows an example.
Diagnostic -digital input example
Figure 75 om9306_56_pic_24x0062550en.wmf
2.9.2 Program version
From the set-up menu access is given to monitor information on the software installed
as illustrated on Figure 76.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-67 / 78
Access to program version information
Figure 76 contouch_89x0198620en.wmf
Information is given on the version number of the human-machine-interface software,
the controller version, and the date of the controller software as illustrated in Fig-
ure 77.
Program version information
Figure 77 om9306_56_pic_61x0062740en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-68 / 78 Language UK
2.9.3 Plant layout
Information on communication addresses, and set-up of the units used for pressure
measurements are accessed from the system dialog window under set-up as illustrated
on Figure 78.
Access to plant layout
Figure 78 contouch_91x0198640en.wmf
Plant layout dialog window
Figure 79 om9306_56_pic_61x0062730en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-69 / 78
2.9.4 Display layout
The elements displayed on the touchscreen depend on what is enabled / activated on
the controller. To view the status of the individual elements the display layout menu
can be used. The menu is accessed from the system dialog window under set-up as
illustrated onFigure 80.
Access to plant layout
Figure 80 contouch_93x0198660en.wmf
The menu indicates the viewing status for each screen element (see Figure 81). No
means that the element is not chosen / activated and therefore is not present on the
display. The arrow in the lower right corner switches to a screen with more elements.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-70 / 78 Language UK
Plant layout dialog window
Figure 81 om9306_56_pic_25x0062560en.wmf
2.9.5 Plant settings
Access to timers, counters, and limits for the plant is given from the set-up dialog
window as illustrated in Figure 82.
Access to plant settings
Figure 82 contouch_95x0198680en.wmf
The plant settings dialog window is illustrated in Figure 83.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-71 / 78
Plant settings dialog window
Figure 83 om9306_56_pic_61x0062750en.wmf
From the plant setting dialog window (Figure 83) access is given to timer settings, hour
counters, and plant settings.
Timer settings
Several timers are used in the system. These timers are accessible in the timer settings
dialog window, accessed from the plant setting dialog window as illustrated in Fig-
ure 84.
Acess to the timer settings
Figure 84 contouch_97x0198700en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-72 / 78 Language UK
The timers menu is divided into five categories: sequence, surveillance, power, shared,
and communication. Notice that each category may contain several pictures. If avail-
able the next windows is accessed by clicking the arrow located in the lower right
corner. The value for the timer can be modified by clicking the dark grey button next
to each timer name. See also Figure 85 for an example.
Timer settings example
Figure 85 om9306_56_pic_12x0062450en.wmf
Hour Counters
The hour counters menu actually holds bothhours counters as well as start counters.
Here the monitoring and configuration of the counters can be carried out. Access to
the counters is given from the plant settings dialog window under the set-up menu as
illustrated in Figure 86.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-73 / 78
Access to houer counter settings
Figure 86 contouch_99x0198720en.wmf
The counters are sorted into five main groups: Boiler, burner, fuel, water, and steam.
An example of the counter dialog windows is illustrated in Figure 87. Again notice
that each category may contain several pictures. If available the next windows is ac-
cessed by clicking the arrow located in the lower right corner.
Counter settings example
Figure 87 om9306_56_pic_15x0062470en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-74 / 78 Language UK
Typically each counter has a total counter that is not resettable (it loops as a mechanical
counter), a total service counter that can be used to keep track of the system since last
service and a service value limit that can be used to generate a service is needed
alarm. Notice that the service counter value can be manually modified.
Plant Settings
The plant settings sub menu gives access to system parameters configuring the be-
haviour of the system. The parameters can e.g. be actuator positions during the different
steps in the start up sequence or the fuel/air ratio. Themenu is accessed from the plant
settings dialog window under the set-up menu as illustrated in Figure 88
Access to plant limits settings
Figure 88 contouch_101x0197780en.wmf
The menu contains two submenus: Plant limits and Ratio. Plant limits (parameters)
concerning firing, ignition, purging, etc are done from this dialog window. An example
is illustrated in Figure 89.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-75 / 78
Plant limits
Figure 89 om9306_56_pic_20x0062500en.wmf
Notice that several pictures are available by pressing the arrow in the lower right corner.
Ratio
The Ratio submenu concerns air/fuel ratio for different load situations.The dialog
window for heavy fuel oil is illustrated in Figure 90 . For each of the displayed load
levels (oil flow) the corresponding air flow can be entered. Notice the corr. value in
the lower right corner. This correction factor is multiplied on all flows allowing for a
global displacement of the air/fuel curve. The factor is especially used for inert gas
systems.
Flow ration - air/HFO
Figure 90 om9306_56_pic_21x0062520en.wmf
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-76 / 78 Language UK
By pressing the arrow in the lower right corner the same picture is available for Diesel
Oil.
Oil summarizer
The Oil summarizer button (See Figure 91) allows for quick access to the oil con-
sumption monitoring picture.
Access to the oil summarizer
Figure 91 contouch_104x0197810en.wmf
The picture (See Figure 92) shows the total amount of fuel oil that has been used. The
value is an integration of the flow meter measurement if available. Notice that the value
will loop when the maximum number is reached much like a normal mechanical coun-
ter. The total service litre functions in the same way but like the other counters it is
also here possible to enter a service value limit that will generate an alarm as well as
reset the counter.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
Language UK 23-77 / 78
Oil summarizer picture
Figure 92 om9306_56_hc_001x0062310en.wmf
2.9.6 Log-out
Trying to change a parameter often requires a password. After the correct password
has been entered access is granted for 60 minutes. As the 60 minutes time out the system
again requires the password to be entered. It is possible to remove the grant before the
60 minutes by pressing the log-out button hence requiring the password to be entered.
MONITORING AND CONTROL VIA TOUCH SCREEN OM9306_56#A.2
23-78 / 78 Language UK
Table of contents
Burner sequence diagram
Description Document ID Page
.
Burner sequence diagram............................................ OM5560_94.............. 24-2
TABLE OF CONTENTS
Language UK 24-1 / 7
Burner sequence diagram
1 General
The following section describes the burner firing sequence for KBO-E modulating
pressure atomising burners. Figure 1 shows a guide to the diagrams, and Figure 2 to
Figure 5 show the burner firing sequence.
The burner firing sequence, e.g. start, purge, ignition, etc., is handled by the control
system. The sequence is divided into a number of steps, which are executed one by
one. When a specified step is active, the control system activates a number of output
signals and timers. In this way the necessary execution and surveillance of these actions
can be performed. On the control panel the actual sequence step will be indicated.
The burner firing sequence consists of 13 steps. The steps 0-8 handle the burner start
sequence, and the steps 10-13 concern the burner stop sequence. In the normal oper-
ation of the burner, step 8 (mod free) will be active. In this step the burner operates in
modulation free mode, and the load is controlled by the steam pressure regulation
output. If the steam pressure rises above the set point for stop of the burner, the control
system initiates the burner stop sequence. When the stop sequence is completed, the
burner will be in step 0 (ready). If the steam pressure falls below the set point for start
of the burner, a new start-up sequence will be initiated.
In addition to these steps, the sequence is provided with a stop step and a shutdown
step. The stop step must be selected on the control panel. In this step the burner remains
stopped regardless of the steam pressure. The shutdown step is active if one or more
safety interlock shut downs are present. If a safety interlock shut down arises in any
one of the sequence steps, the burner firing sequence is immediately interrupted. When
the safety interlock circuit is restored, and the shut down is reset, the sequence returns
to step 0 (ready).
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
24-2 / 7 Language UK
Diagram
STEP No.
Sequence
STEP No.
Sequence
(continued)
Guide to diagram
Conditions which must be fulfilled before leaving the above
step and entering the next step
When entering a sequence step, the associated outputs
will be active, and the described actions will be executed
Shut-down of the burner
due to one or more active
safety interlocks. The
sequence will return to
step shut-down
Normal stop
of the burner
Continuance of sequence step
Figure 1 om5560_94_seqguix0055840en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 24-3 / 7
Sequence diagram
STEP
Shut-down
Power on
One or more safety interlocks active
Deactivate start request to PMS
Stop ignition (switch off power to ignition transformer)
Deactivate oil valves
Close oil safety valves 1 + 2
Deactivate start signal to burner motor
Set servo motors to closed position
Set all timers to zero, except timers for water level alarms/
shut downs
Safety interlocks OK. When all shut downs can be and are
reset change to step 0 (ready)
Set servo motors to closed position
Stop burner motor
In automatic mode change step if boiler pressure is
lower than set point chosen + master start difference
In manual mode change step if soft key for start is
activated
Send start request to PMS system, if this possibility is
provided in the control system
Start timer for PMS feedback signal
Start permission from PMS system given
STEP
Stopped
To enter this step it must be chosen on the control panel
Set all timers to zero
Set burner to stop mode
When the step is changed to step 0 (ready) on the control
panel, the burner stop mode is canceled
STEP 0
Ready
STEP 1
Starting
STEP 1
Starting
(continued)
Start burner motor
Reset timer for PMS feedback
Start timer for maximum start sequence time
Start timer for burner motor start
Burner firing sequence
Continued in next figure
Shut-down Stop
Stay in step stopped
Shut-down
Stay in shut-down step if
safety interlocks are not OK
Stop
Stay in step 0 (ready)
Shut-down
Shut-down Stop
Change to step 0 (ready)
Stop
Change to step 0 (ready)
Reset timer for maximum
start sequence time
Shut-down
Feedback signal for burner motor running
Figure 2 om5560_94_seqrmsx0055850en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
24-4 / 7 Language UK
Sequence diagram, continued
STEP 2
Purge
Set servo motors to purge position
Start timer for servo motors in position
Feedback signal for servo motors in position
If servo motors position are OK during purge period, change
step
If servo motors position are not OK, return to step 2 again
Set servo motors to ignition position
Start timer for servo motor in position
Start timer for oil heating
Feedback signal for servo motors in position
Continue when timer periods for oil heating have expired
Start ignition (energize ignition transformer)
Open oil safety valves 1 + 2
Start timer for ignition
Start timer for purge
STEP 3
Ignition
position
STEP 4
Ignition
Burner firing sequence continued from previous figure
Continued in next figure
Shut-down Stop
Change to step 0 (ready)
Reset timers for maximum
start sequence time and
purge time
Stop
Stop burner motor
Change to step 0 (ready)
Reset timers for maximum
start sequence time and
ignition position and
oil heating
Shut-down
Shut-down Stop
Stop ignition, close oil
safety valves 1 + 2
Reset timer for maximum
start sequence time
Change to step 0 (ready)
STEP 2
Purge
(continued)
Shut-down Stop
Change to step 0 (ready)
Reset timer for maximum
start sequence time
Change step when timer period for ignition has expired
STEP 5
Safety time
Activate oil valves
Start timer for safety time
Continue when timer period for safety time has expired
Stop
Stop ignition
Reset timer for maximum
start sequence time
Change to step 10
(steam purge position)
Shut-down
Figure 3 om5560_94_seqrmsx0055860en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 24-5 / 7
Sequence diagram, continued
Activate flame surveillance
Reset timer for maximum start sequence time
Burner firing sequence continued from previous figure
Shut-down Stop
Change to step 10
(steam purge position)
STEP 6
Flame
stable
Shut-down Stop
Stop ignition
stop sequence initiates
Change to step 10
(steam purge position)
STEP 5
Safety time
(continued)
Start timer for flame stable
Stop ignition (switch off ignition transformer)
Change step when timer period for flame stable has expired
STEP 8
Rising/
mod. free
(continued)
Modulating operation of the burner according to the signals
from the steam pressure transmitter
In automatic mode change step if boiler pressure is
higher than set point chosen + stop differential set point
In manual mode change step if soft key for stop is activated
Shut-down Stop
Change to step 10
(Steam purge position)
STEP 11
Steam
purge 1
Shut-down
Deactivate oil valves
Close oil safety valves 1 + 2
Deactivate flame surveillance
Continued in next figure
STEP 13
Postpurge
Set servo motors to purge position
Start timer for servo motors in position
Feedback signal for servo motors in position
Shut-down
Figure 4 om5560_94_seqrmsx0055870en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
24-6 / 7 Language UK
Sequence diagram, continued
Start timer for postpurge. If timer is set to 0 sec. the
furnace will not be purged.
Change to step 0 (ready) when timer period for postpurge
has expired
Burner firing sequence continued from previous figure
STEP 0
Ready
Shut-down
STEP 13
Postpurge
(continued)
Figure 5 om5560_94_seqrmsx0055880en.wmf
BURNER SEQUENCE DIAGRAM OM5560_94#B.1
Language UK 24-7 / 7
Table of contents
Flame safeguard
Description Document ID Page
.
Flame safeguard........................................................ OM8200_04.............. 25-2
TABLE OF CONTENTS
Language UK 25-1 / 2
Flame safeguard
1 Description
The flame safeguard LAE10 is designed for the supervision of the oil flame in con-
nection with a photo cell when the burner is running in manual mode. It comprises a
power section, a flame signal amplifier, a flame relay and a combined flame-present
indicator lamp and reset button.
Note: The flame safeguard has no function when the burner is running in auto-
matic mode.
In the event of non-ignition of the flame or loss of flame during burner operation, the
supply of fuel is always interrupted instantaneously. The unit can be reset by pushing
the reset button on the flame safeguard. Any flame signal - in normal operation or a
faulty flame signal - is signalled by the indicator lamp. The switching function needed
to enter the flame signal to the control circuit of the burner system is provided by the
flame relay FR of the flame safeguard. Figure 1 shows an illustration of the con-
nection diagram for the flame safeguard. The connection of the terminals can be found
in the chapter containing the electric diagrams.
Connection diagram
Figure 1 om8200_04_lae10x0058160en.wmf
FLAME SAFEGUARD OM8200_04#A.2
25-2 / 2 Language UK
Table of contents
Menu structure for panels
Description Document ID Page
.
Menu tree................................................................. Menu tree 6_08......... 26-2
Explanation list for menu tree..................................... OM9306_34.............. 26-25
TABLE OF CONTENTS
Language UK 26-1 / 59
Menu tree
MENU TREE Menu tree 6_08#B.1
26-2 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
-
[
S
E
L
E
C
T

1
]
N
-
[
S
E
L
E
C
T

2
]
N
-
[
S
E
L
E
C
T

3
]
N
-
[
S
T
A
T
E
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
-
K
E
Y

P
O
S
I
T
I
O
N
N
-
R
E
Q
U
E
S
T

K
E
Y
N
-
[
S
T
A
T
E
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
1
B
O
I
L
E
R
1
2
B
O
I
L
E
R

P
R
E
S
N

B
A
R
1
-
2
-
1
H
I
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
.
5
1
-
2
-
2
H
I
G
H

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
.
3
1
-
2
-
3
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

4
1
-
2
-
7
A
C
T
U
A
L

S
P
.
N

B
A
R
n
p
1
-
2
-
8
S
E
T
P
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

7
1
-
2
-
9
S
E
T
P
.
H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

1
6
1
-
2
-
1
0
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

5
1
-
2
-
1
1
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

1
1
-
2
-
1
2
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
0
1
-
2
-
1
3
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
2
-
1
4
R
E
G

O
U
T
P
U
T
N

%
n
p
1
-
2
-
1
5
N
E
U
T
R
A
L
Z
O
N
E
N

B
A
R

p
w
:
c
u
l
o
:

0
h
i
:

5
d
e
f
:

0
,
5
1
-
2
-
1
6
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
1
-
3
W
A
T
E
R

L
E
V
E
L
N

m
m
1
-
3
-
1
H
I
.
S
H
T
.
D
W
N
.
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

2
5
0
1
-
3
-
2
H
I
G
H

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

1
5
0
1
-
3
-
3
L
O
W

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

-
1
0
0
1
-
3
-
4
L
O
.
S
H
T
.
D
W
N
.
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

-
1
5
0
1
-
3
-
1
2
A
C
T
U
A
L

S
P
.
N

m
m
n
p
1
-
3
-
1
3
S
E
T
P
.
O
F
F
S
E
T
N

m
m
n
p
1
-
3
-
1
4
S
E
T
P
.
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

-
3
0
1
-
3
-
1
5
S
E
T
P
.
H
I
G
H
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

0
1
-
3
-
9
D
E
A
D
Z
O
N
E
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
1
-
3
-
1
0
I
-
L
O
W

L
I
M
I
T
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

1
d
e
f
:

0
1
-
3
-
1
1
I
-
H
I
G
H

L
I
M
I
T
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

1
d
e
f
:

0
1
-
3
-
1
6
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

3
1
-
3
-
1
7
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
1
-
3
-
1
8
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
3
0
1
-
3
-
1
9
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
3
-
2
0
P
.
P
A
R
T
N

%
n
p
1
-
3
-
2
1
I
.
P
A
R
T
N

%
n
p
1
-
3
-
2
2
D
.
P
A
R
T
N

%
n
p
1
-
3
-
2
3
R
E
G

O
U
T
P
U
T
N

%
n
p
1
-
R
E
M
O
T
E

C
T
R
L
N

%
n
p
1
-
N
O
R
M
A
L

L
I
M
I
T
N

m
m
n
p
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
3
-
2
4
S
T
B
Y

L
I
M
I
T
N

m
m
n
p
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
4
-
1

W
A
T
E
R

F
L
O
W
N
1
-
4
-
2
A
C
T
U
A
L

S
P
.
N
n
p
1
-
4
-
3
P
N
p
w
:
c
u
l
o
:

0
,
1
h
i
:

1
0
d
e
f
:

0
,
3
1
-
4
-
4
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
,
1
h
i
:

1
0
d
e
f
:

0
,
5
1
-
4
-
5
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

7
1
-
4
-
6
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
4
-
7
R
E
G

O
U
T
P
U
T
N

%
1
-
5
-
1
C
O
M
M
O
N

P
R
E
S
N

B
A
R
1
-
5
-
2
H
I
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
.
5
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-3 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
1
-
5
-
3
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

4
1
-
5
-
6
A
C
T
U
A
L

S
P
.
N

B
A
R
1
-
5
-
7
S
E
T
P
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

6
1
-
5
-
8
S
E
T
P
.
H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

1
5
1
-
5
-
9
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

1
6
1
-
5
-
1
0
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
1
-
5
-
1
1
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

6
0
1
-
5
-
1
2
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
5
-
1
3
R
E
G

O
U
T
P
U
T
N

%
n
p
1
-
5
-
1
4
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
1
-
6
-
1
T
E
M
P
.

I
N
L
E
T
N

C
1
-
6
-
2
H
I
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
-
6
-
3
H
I
G
H

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
-
6
-
4
L
O
W

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

0
1
-
6
-
5
L
O
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

0
1
-
7
-
1
T
E
M
P
.

O
U
T
L
E
T
N

C
1
-
7
-
2
H
I
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
-
7
-
3
H
I
G
H

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
-
7
-
4
L
O
W

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

0
1
-
7
-
5
L
O
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

0
1
-
8
-
1
D
I
F
F
.

P
R
E
S
S
.
N

m
m
1
-
8
-
2
H
I
.
S
H
T
.
D
W
N
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
5
0
1
-
8
-
3
H
I
G
H

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
3
0
1
-
8
-
4
L
O
W

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

0
1
-
8
-
5
L
O
.
S
H
T
.
D
W
N
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

0
1
-
9
-
1
M
E

L
O
A
D
N

%
1
-
9
-
2
H
I
.
S
H
T
.
D
W
N
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
1
0
d
e
f
:

1
1
0
1
-
9
-
3
H
I
G
H

A
L
A
R
M
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
1
0
d
e
f
:

1
1
0
1
-
9
-
4
L
O
W

A
L
A
R
M
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
1
-
9
-
5
L
O
.
S
H
T
.
D
W
N
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
-
[
S
T
A
T
E
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
2
-
F
U
E
L

O
I
L
2
-
1
F
.
O
I
L

T
E
M
P
N

C
2
-
1
-
1
H
I
.
S
H
T
.
D
W
N
.
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
4
5
2
-
1
-
2
H
I
G
H

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
4
0
2
-
1
-
3
L
O
W

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
1
0
2
-
1
-
4
L
O
.
S
H
T
.
D
W
N
.
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

9
5
2
-
1
-
9
S
E
T
P
.
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
3
0
2
S
E
T
P
.

H
I
G
H
N

C
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
3
0
2
-
1
-
1
0
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

2
2
-
1
-
1
1
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
2
-
1
-
1
2
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
6
0
2
-
1
-
1
3
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
2
-
1
-
1
4
M
I
N

P
U
L
S
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
2
h
i
:

5
d
e
f
:

0
.
5
2
-
1
-
1
5
R
U
N

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

1
0
h
i
:

1
8
0
d
e
f
:

3
5
2
-
1
-
1
6
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
2
-
1
-
1
7
N
E
U
T
R
A
L
Z
O
N
E
N

C
p
w
:
c
u
l
o
:

0
h
i
:

1
0
d
e
f
:

2
2
-
2
F
.
O
I
L

P
R
E
S
N

B
A
R
2
-
2
-
1
H
I
.
S
H
T
.
D
O
W
N
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

4
2
-
2
-
1
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

1
,
5
2
-
2
-
2
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

1
,
6
2
-
2
-
3
L
O
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

1
2
-
2
-
4
L
O
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

1
,
5
2
-
2
-
9
S
E
T
P
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

4
0
d
e
f
:

2
2
2
-
2
-
1
0
I
-
L
O
W

L
I
M
I
T
N
p
w
:
c
u
l
o
:

0
h
i
:

1
d
e
f
:

1
2
-
2
-
1
1
I
-
H
I
G
H

L
I
M
I
T
N
p
w
:
c
u
l
o
:

0
h
i
:

1
d
e
f
:

1
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

2

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-4 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
2
-
2
-
1
2
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

1
.
5
2
-
2
-
1
3
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
2
-
2
-
1
4
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
5
2
-
2
-
1
5
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
2
-
2
-
1
6
M
I
N

P
U
L
S
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
2
h
i
:

5
0
d
e
f
:

0
.
5
2
-
2
-
1
7
R
U
N

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

1
0
h
i
:

1
8
0
d
e
f
:

3
0
2
-
2
-
1
8
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
2
-
3
F
.
O
I
L

F
L
O
W
N

%
2
-
3
-
1
A
C
T
U
A
L

S
P
.
N

%
n
p
2
-
3
-
2
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
4
2
-
3
-
3
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
0
d
e
f
:

0
.
5
2
-
3
-
4
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

4
2
-
3
-
5
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
2
-
3
-
6
P
.
P
A
R
T
N

%
n
p
2
-
3
-
7
I
.
P
A
R
T
N

%
n
p
2
-
3
-
8
D
.
P
A
R
T
N

%
n
p
2
-
3
-
9
M
V

S
A
V
E
N

%
n
p
2
-
3
-
1
0
R
E
G

O
U
T
P
U
T
N

%
n
p
2
-
3
-
1
1
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
2
-
2
F
.
O
.

B
U
R
N
E
R

T
N

B
A
R
2
-
2
-
1
H
I
.
S
H
T
.
D
O
W
N
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

2
0
0
2
-
2
-
3
L
O
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

9
5
-
-
-
-
-
[
S
T
A
T
E
]
n
p
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
n
p
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
3
A
I
R
3
-
1
A
I
R

F
L
O
W
N

%
3
-
1
-
1
L
O
.
S
H
T
.
D
W
N
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
3
-
1
-
3
A
C
T
U
A
L

S
P
.
N

%
n
p
3
-
1
-
4
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
4
3
-
1
-
5
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
0
d
e
f
:

0
.
5
3
-
1
-
6
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

4
3
-
1
-
7
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
3
-
1
-
8
R
E
G

O
U
T
P
U
T
N

%
n
p
3
-
1
-
9
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
3
-
2
-
1
A
T
M
.
S
T
M
.
P
R
S
N

B
A
R
3
-
2
-
2
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

1
1
d
e
f
:

2
3
-
2
-
3
L
O
.
S
H
T
.
D
W
N
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

1
1
d
e
f
:

1
.
5
3
-
2
-
6
A
C
T
U
A
L

S
P
.
N

B
A
R
n
p
3
-
2
-
7
P
N
p
w
:
c
u
l
o
:

0
.
0
1
h
i
:

1
0
d
e
f
:

3
.
5
3
-
2
-
8
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

0
.
5
3
-
2
-
9
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

6
0
0
d
e
f
:

3
3
-
2
-
1
0
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
3
-
2
-
1
1
M
I
N

P
U
L
S
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
2
h
i
:

5
d
e
f
:

0
.
5
3
-
2
-
1
2
R
U
N

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

1
0
h
i
:

1
8
0
d
e
f
:

3
5
3
-
2
-
1
3
R
E
G

O
U
T
P
U
T
N

%
n
p
3
-
2
-
1
4
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
-
-
-
-
-
[
S
T
A
T
E
]
N
n
p
-
[
S
T
A
T
E
]
[
L
O
A
D
]
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
4
-
1
-
S
E
R
V
O
4
-
1
S
E
R
V
O

P
O
S
.
N

%
4
-
1
-
1
A
C
T
U
A
L

S
P
.
N

%
n
p
4
-
1
-
2
N
E
U
T
R
A
L
Z
O
N
E
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
4
-
1
-
3
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
-
-
1
-
[
S
T
A
T
E
]
[
L
O
A
D
]
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
4
-
1
-
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

3

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-5 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
4
-
1
A
I
R

S
E
R
V
O
N

%
4
-
1
-
1
A
C
T
U
A
L

S
P
.
N

%
n
p
4
-
1
-
2
N
E
U
T
R
A
L
Z
O
N
E
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
4
-
1
-
3
P
N
p
w
:
c
u
l
o
:

0
.
0
1
h
i
:

1
0
d
e
f
:

3
.
5
4
-
1
-
4
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

0
.
5
4
-
1
-
5
T
.
I
N
T
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

6
0
0
d
e
f
:

3
4
-
1
-
6
T
.
D
I
F
F
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
4
-
1
-
7
M
I
N

P
U
L
S
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
2
h
i
:

5
d
e
f
:

0
.
5
4
-
1
-
8
R
U
N

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

1
0
h
i
:

1
8
0
d
e
f
:

3
5
4
-
1
-
R
E
G

O
U
T
P
U
T
N

%
n
p
4
-
1
-
3
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
4
-
1
-
4
-
1
O
I
L

S
E
R
V
O
N

%
4
-
1
-
1
A
C
T
U
A
L

S
P
.
N

%
n
p
4
-
1
-
2
N
E
U
T
R
A
L
Z
O
N
E
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
4
-
1
-
3
P
N
p
w
:
c
u
l
o
:

0
.
0
1
h
i
:

1
0
d
e
f
:

3
.
5
4
-
1
-
4
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

0
.
5
4
-
1
-
5
T
.
I
N
T
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

6
0
0
d
e
f
:

3
4
-
1
-
6
T
.
D
I
F
F
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
4
-
1
-
7
M
I
N

P
U
L
S
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
2
h
i
:

5
d
e
f
:

0
.
5
4
-
1
-
8
R
U
N

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

1
0
h
i
:

1
8
0
d
e
f
:

3
5
4
-
1
-
R
E
G

O
U
T
P
U
T
N

%
n
p
4
-
1
-
3
R
E
M
O
T
E

C
T
R
L
N
p
w
:
c
u
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
5
C
O
M
B
U
S
T
5
-
1
O
I
L

P
R
E
S
S

N

N

B
A
R
n
p
5
-
1
-
1
S
M
K
.

D
E
N
S
I
T
N

%
5
-
1
-
1
-
H
I
G
H

A
L
A
R
M
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
5
-
1
-
2
O
X
Y
G
E
N
N

%
5
-
1
-
2
-
H
I
G
H

A
L
A
R
M
N

%
p
w
:
c
u
l
o
:

0
,
0
h
i
:

1
0
0
,
0
d
e
f
:

1
0
0
,
0
5
-
1
-
3
T
E
M
P
.

U
P
T
A
K
N

C
5
-
1
-
3
-
H
I
.
S
H
T
.
D
W
N
.
N

C
p
w
:
c
u
l
o
:

0
h
i
:

5
0
0
d
e
f
:

4
5
0
5
-
1
-
3
-
H
I
G
H

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
h
i
:

5
0
0
d
e
f
:

4
5
0
5
-
2
W
I
N
D
B
O
X
N

C
5
-
2
-
1
H
I
.
S
H
T
.
D
O
W
N
N

C
p
w
:
c
u
l
o
:

0
,
0
h
i
:

4
0
0
,
0
d
e
f
:

1
5
0
5
-
2
-
1
H
I
G
H

A
L
A
R
M
N

C
p
w
:
c
u
l
o
:

0
,
0
h
i
:

4
0
0
,
0
d
e
f
:

1
4
0
-
-
-
-
-
-
[
S
T
A
T
E
]
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
6
P
A
R
T
N
E
R
n
p
6
-
1
1
B
O
I
L
E
R

P
R
E
S
N

B
A
R
n
p
6
-
2
2
W
A
T
E
R

L
E
V
E
L
N

m
m
n
p
6
-
3
3
F
.
O
I
L

F
L
O
W
N

%
n
p
6
-
4
4
A
I
R

F
L
O
W
N

%
n
p
6
5
O
I
L

S
E
R
V
O
N

%
n
p
6
6
A
I
R

S
E
R
V
O
N

%
n
p
6
-
5
7
A
T
M
.
S
T
M
.
P
R
S
N

B
A
R
n
p
6
-
6
8
O
I
L

P
R
S

N
Z
.
N

B
A
R
n
p
6
-
7
9
O
X
Y
G
E
N
N

%
n
p
6
-
8
1
0
S
M
O
K
E

D
E
N
S
N

%
n
p
6
-
9
1
1
I
N
E
R
T

G
A
S
N
n
p
6
-
1
0
1
2
S
T
A
T
E
N
n
p
6
-
1
1
1
3
C
T
R
L

M
O
D
E
N
n
p
7
C
M
N

C
T
R
L
7
-
1
P
U
M
P

C
T
R
L
7
-
1
-
1
-
O
I
L

P
U
M
P
n
p
7
-
1
-
1
-
F
.
O
.
P
M
P
1

S
E
L
.
N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

4

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-6 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
7
-
1
-
1
-
S
T
A
T
E
N
n
p
7
-
1
-
1
-
F
.
O
.
P
M
P
2

S
E
L
.
N
n
p
7
-
1
-
1
-
S
T
A
T
E
N
n
p
7
-
1
-
1
-
F
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
1
-
F
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
7
-
1
-
1
-
F
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
1
-
F
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
7
-
1
-
2
C
H
E
M

P
M
P
n
p
7
-
1
-
2
-
C
H
E
M

P
M
P
1
N
n
p
7
-
1
-
2
-
C
H
E
M

P
M
P
2
N
n
p
7
-
1
-
3
-
W
A
T
E
R

P
U
M
P
n
p
7
-
1
-
3
-
W
A
T
E
R

P
U
M
P
n
p
7
-
1
-
3
-
P
U
M
P

1
_
1

S
E
L
.
N
n
p
7
-
1
-
3
-
M
O
D
E
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
P
U
M
P

1
_
2

S
E
L
.
N
n
p
7
-
1
-
3
-
M
O
D
E
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
P
U
M
P

2
_
1

S
E
L
.
N
n
p
7
-
1
-
3
-
M
O
D
E
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
P
U
M
P

2
_
2

S
E
L
.
N
n
p
7
-
1
-
3
-
M
O
D
E
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
F
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
F
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
F
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
F
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
F
.
P
M
P
3

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
F
.
P
M
P
3

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
F
.
P
M
P
4

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
F
.
P
M
P
4

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
C
I
R
C
U
L
A
T
I
O
N

P
U
M
P
n
p
7
-
1
-
3
-
C
.
P
M
P
1

S
E
L
.
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
C
.
P
M
P
2

S
E
L
.
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
7
-
1
-
3
-
C
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
C
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
C
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
7
-
1
-
3
-
C
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
7
-
1
-
3
-
W
A
T
E
R

P
U
M
P

E
G
B
n
p
7
-
1
-
3
-
P
U
M
P

5

S
E
L
.
N
n
p
7
M
O
D
E
N
n
p
7
S
T
A
T
E
N
n
p
7
-
1
-
3
-
P
U
M
P

6

S
E
L
.
N
n
p
7
-
1
-
3
-
M
O
D
E
N
n
p
7
-
1
-
3
-
S
T
A
T
E
N
n
p
-
-
-
-
-
-
C
H
E
M

P
M
P
-
C
H
E
M

P
M
P
1
N
n
p
7
-
2
S
M
O
K
E

B
L
O
W
n
p
7
-
2
-
1
S
M
O
K
E

B
L
O
W
E
R

1
N
n
p
d
e
f
:

O
N
7
-
3
S
T
E
A
M

D
U
M
P
7
-
3
-
1
S
T
E
A
M

D
U
M
P
N

B
A
R
7
-
3
-
1
-
H
I
.
S
H
T
.
D
W
N
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
.
5
7
-
3
-
1
-
L
O
W

A
L
A
R
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

4
7
-
3
-
1
-
A
C
T
U
A
L

S
P
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
7
-
3
-
1
-
S
E
T
P
.
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

5

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-7 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
7
-
3
-
1
-
S
E
T
P
.
H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
7
-
3
-
1
-
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

5
7
-
3
-
1
-
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
7
-
3
-
1
-
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

3
7
-
3
-
1
-
T
.
D
I
F
F
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
7
-
3
-
1
-
R
E
G

O
U
T
P
U
T
N

%
n
p
7
-
3
-
1
-
R
E
M
O
T
E

C
T
R
L
.
N
p
w
:
c
u
-
-
-
-
-
-
[
S
T
A
T
E
]
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
7
-
4
S
A
L
I
N
I
T
Y
7
-
4
-
1
-
S
A
L
I
N
I
T
Y
N

p
p
m
7
-
4
-
1
-
H
I
.
S
H
T
.
D
W
N
.
N

p
p
m
p
w
:
c
u
l
o
:

0
h
i
:

5
0
d
e
f
:

2
5
7
-
4
-
1
-
H
I
G
H

A
L
A
R
M
N

p
p
m
p
w
:
c
u
l
o
:

0
h
i
:

5
0
d
e
f
:

1
5
-
-
-
-
-
-
[
S
T
A
T
E
]

n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
]
N
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
7
-
5
I
N
E
R
T

G
A
S
7
-
5
-
1
M
I
N

L
O
A
D
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
7
-
5
-
2
F
O
R
C
E
N
p
w
:
c
u
7
-
6

F
E
E
D

W
A
T
E
R
(
3
p
t
.

t
e
x
t
s

/

2
p
t
.

t
e
x
t
s
)
7
-
6
-
1
(
3
p
t
.

t
e
x
t
s

/

2
p
t
.

t
e
x
t
s
)
7
-
6
-
1
-
F
W

O
U
T
P
U
T

/

N

%
n
p
7
-
6
-
1
-
F
W

O
P
E
N

/

N
n
p
7
-
6
-
1
-
0
%
F
W

O
P
E
N

/

0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

0
7
-
6
-
1
-
1
0
%
F
W

O
P
E
N

/

1
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
0
7
-
6
-
1
-
2
0
%
F
W

O
P
E
N

/

2
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

2
0
7
-
6
-
1
-
3
0
%
F
W

O
P
E
N

/

3
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

3
0
7
-
6
-
1
-
4
0
%
F
W

O
P
E
N

/

4
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

4
0
7
-
6
-
1
-
5
0
%
F
W

O
P
E
N

/

5
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

5
0
7
-
6
-
1
-
6
0
%
F
W

O
P
E
N

/

6
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

6
0
7
-
6
-
1
-
7
0
%
F
W

O
P
E
N

/

7
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

7
0
7
-
6
-
1
-
8
0
%
F
W

O
P
E
N

/

8
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

8
0
7
-
6
-
1
-
9
0
%
F
W

O
P
E
N

/

9
0
%

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

9
0
7
-
6
-
1
-
1
0
0
%
F
W

O
P
E
N

/

N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

1
0
0
7
-
6
-
2
C
O
N
S
T
A
N
T
7
-
6
-
2
-
C
A
L
C
.
M
E
T
H
O
D
N
p
w
:
c
u
d
e
f
:
A
D
D
7
-
6
-
2
-
C
A
L
C
.
F
L
O
W
N
p
w
:
c
u
7
-
6
-
2
-
F
L
O
W

I
N
P
U
T
N
p
w
:
c
u
d
e
f
:
S
T
M
7
-
6
-
2
-
F
O
L
L
O
W

O
I
L
.
V
N
p
w
:
c
u
d
e
f
:
N
O
7
-
6
-
2
-
A
V
.
T
I
M
E

1
/
1
0
S
N
p
w
:
c
u
l
o
:
0
h
i
:

6
4
d
e
f
:
2
0
7
-
6
-
2
-
W
.
O
U
T
.
R
A
M
P
N

%
p
w
:
c
u
l
o
:

1
h
i
:

1
0
0
d
e
f
:

1
0
7
-
6
-
2
-
F
L
O
W

E
R
R
O
R
N
p
w
:
c
u
l
o
:

0
h
i
:

3
0
0
d
e
f
:

1
0
7
-
6
-
2
-
F
L
O
W

O
F
F
S
E
T
N
p
w
:
c
u
l
o
:

0
h
i
:

1
0
d
e
f
:

1
7
-
6
-
2
-
W
.
R
E
G
.
R
A
M
P
N

m
m
p
w
:
c
u
l
o
:

0
,
1
h
i
:

2
d
e
f
:

1
7
-
6
-
2
-
W
L
.
R
E
G
.
M
A
X
N

%
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

3
0
7
-
6
-
2
-
W
L
.
R
E
G
.
M
I
N
N

%
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

-
3
0
7
-
7
-
3
P
I
D

P
A
R
A
M
E
T
E
R
S
7
-
7
-
3
-
1
:
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

3
7
-
7
-
3
-
1
:
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
7
-
7
-
3
-
1
:
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
3
0
7
-
7
-
3
-
1
:
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
7
-
7
-
3
-
2
:
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

3
7
-
7
-
3
-
2
:
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

0
.
5
7
-
7
-
3
-
2
:
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
3
0
7
-
7
-
3
-
2
:
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
7
-
8
F
D

F
A
N

C
O
N
T
R
O
L
7
-
8
-
1
F
O
R
C
E
D

R
U
N
N
p
w
:
c
u
d
e
f
:

n
o
V
A
L
V
E

C
O
R
R
E
C
T
I
O
N

/

C
U
R
V
E

F
U
N
C
T
I
O
N
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

6

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-8 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
7
-
9
A
I
R

F
L
O
W
(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

7
-
9
-
1
L
O
.
S
H
T
.
D
W
N
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
7
-
9
-
3
L
O
.
S
D
.
S
.
G
U
N
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
-
-
-
-
-
-
[
O
I
L

O
P
E
R
A
T
I
O
N
]
n
p
-
-
-
-
-
-
[
S
E
T
P
O
I
N
T

S
E
L
E
C
T
]
N
n
p
1
E
G
E
,

E
G
B
1
2
W
A
T
E
R

L
E
V
E
L
N

m
m
1
-
2
-
2
H
I
G
H

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

8
.
3
1
-
2
-
3
L
O
W

A
L
A
R
M
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

4
1
-
2
-
8
S
E
T
P
.
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

7
1
-
2
-
9
S
E
T
P
.
H
I
G
H
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

1
6
1
-
2
-
1
0
P
N
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

5
1
-
2
-
1
1
T
.
S
A
M
P
L
E
N

S
E
C
p
w
:
c
u
l
o
:

0
.
1
h
i
:

1
0
d
e
f
:

1
1
-
2
-
1
2
T
.
I
N
T
.
N

S
E
C
p
w
:
c
u
l
o
:

0
.
5
h
i
:

9
9
9
.
9
d
e
f
:

1
0
1
-
2
-
1
3
T
.
D
I
F
F
.
N

S
E
C
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
1
-
2
-
1
4
R
E
G

O
U
T
P
U
T
N

%
n
p
1
N
E
U
T
R
A
L
Z
O
N
E
N

B
A
R

p
w
:
c
u
l
o
:

0
h
i
:

5
d
e
f
:

0
,
5
1
N
O
R
M
A
L

L
I
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

5
0
1
-
2
-
1
5
S
T
B
Y

L
I
M
I
T
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

5
0
1
-
3
B
O
I
L
E
R

P
R
E
S
N

B
A
R

1
-
3
-
2
H
I
G
H

A
L
A
R
M
N

B
A
R

p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

1
5
0
1
-
3
-
3
L
O
W

A
L
A
R
M
N

B
A
R

p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

-
1
0
0
1
-
6
-
1
T
E
M
P
.

I
N
L
E
T
N

C
1
-
6
-
2
H
I
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
-
7
-
1
T
E
M
P
.

O
U
T
L
E
T
N

C
1
-
7
-
2
H
I
.
S
H
T
.
D
W
N
N

C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

4
5
0
1
M
E

L
O
A
D
N

%
1
S
E
T
P
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
0
1
A
L
A
R
M

G
R
O
U
P
S
S
H
U
T
D
O
W
N
1
2
1
A
L
A
R
M
1 1
A
U
X
I
L
L
A
R
Y
A
U
X
.

P
M
P

S
E
L
.
1
S
T
A
T
E
8
S
U
R
V
E
I
L
n
p
8
-
1
S
H
T
.
D
W
N
.

I
N
S
P
E
C
T
I
O
N
n
p
8
-
1
-
1
[
S
H
T
.
D
W
N
.

N
U
M
]
N
n
p
8
-
1
-
2
[
S
H
T
.
D
W
N
.

T
E
X
T
]
N
n
p
8
-
2
A
L
A
R
M

I
N
S
P
E
C
T
I
O
N
n
p
8
-
2
-
1
[
A
L
A
R
M

N
U
M
]
N
n
p
8
-
2
-
2
[
A
L
A
R
M

T
E
X
T
]
N
n
p
9
S
E
T
U
P
9
-
1
C
T
R
L

M
O
D
E
n
p
9
-
1
-
1
B
U
R
N
E
R

C
T
R
L

M
O
D
E
N
n
p
9
-
1
-
2
S
Y
S
T
E
M

C
T
R
L
N
n
p
9
-
1
-
3
S
E
T
P
O
I
N
T

S
E
L
E
C
T
N
n
p
9
-
2
-
3
T
I
M
E
R
S

S
E
T
U
P
9
-
2
-
3
-
S
E
Q
U
E
N
C
E
9
-
2
-
3
-
0
S
T
A
R
T

S
T
A
R
T
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

1
2
0
0
9
-
2
-
3
-
1
A
I
R

S
E
R
V
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
2
O
I
L

S
E
R
V
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
3
I
G
N
I
T
E
R

P
O
S
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

1
0
9
-
2
-
3
-
4
F
D
.
F
A
N

S
T
.
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

2
5
9
-
2
-
3
-
5
P
U
R
G
E
N

S
E
C
p
w
:
s
u
l
o
:

2
3
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
6
I
G
N
I
T
I
O
N
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
0
d
e
f
:

1
0
9
-
2
-
3
-
7
S
A
F
E
T
Y

T
I
M
E
N

S
E
C
p
w
:
s
u
l
o
:

2
h
i
:

1
5
d
e
f
:

5
9
-
2
-
3
-
8
S
T
A
R
T

S
E
Q
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

1
8
0
9
-
2
-
3
-
9
F
L
A
M
E

S
T
A
B
.
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
0
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

7

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-9 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
2
-
3
-
1
0
L
O
W

F
I
R
I
N
G
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
0
9
-
2
-
3
-
1
1
R
I
S
I
N
G

T
I
M
E
N

S
E
C
p
w
:
c
u
l
o
:

3
0
0
h
i
:

3
6
0
0
d
e
f
:

6
0
0
9
-
2
-
3
-
1
2
S
T
E
A
M

P
G
.
P
O
N

S
E
C
p
w
:
c
u
l
o
:

5
h
i
:

1
2
0
d
e
f
:

2
0
9
-
2
-
3
-
1
3
S
T
E
A
M

P
U
R
G
1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

3
0
9
-
2
-
3
-
1
4
S
T
E
A
M

P
U
R
G
2
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
0
d
e
f
:

2
0
9
1
5
P
O
S
T
P
U
R
G
E
N

S
E
C
n
p
l
o
:

1
h
i
:

1
2
0
0
d
e
f
:

0
9
1
6
I
G
.
P
U
R
G
E

V
L
V
N

S
E
C
n
p
l
o
:

0
h
i
:

1
0
d
e
f
:

1
0
9
1
7
O
I
L

C
I
R
C

T
.
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
0
0
d
e
f
:

6
0
9
-
2
-
3
-
S
U
R
V
E
I
L
L
A
N
C
E
9
-
2
-
3
-
0
A
I
R
F
A
N

S
T
A
R
N

S
E
C
p
w
:
c
u
l
o
:

5
h
i
:

1
2
0
d
e
f
:

2
0
9
-
2
-
3
-
1
W
A
T
E
R

H
I
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
3
-
2
W
A
T
E
R

H
I
.
A
L
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
3
-
3
W
A
T
E
R
.
L
O
.
A
L
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
3
-
4
W
A
T
E
R

L
O
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

5
9
-
2
-
3
-
5
W
A
T
E
R

S
W

L
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

5
9
-
2
-
3
-
6
O
I
L

V
L
V

C
L
S
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
0
d
e
f
:

3
9
-
2
-
3
-
7
I
G
N
I
T
E
R

O
U
T
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

5
0
9
-
2
-
3
-
8
P
M
S

F
E
E
D
B
A
C
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

1
2
0
0
d
e
f
:

1
6
0
9
-
2
-
3
-
9
S
E
R
V
O

P
O
S
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

1
2
0
0
d
e
f
:

1
2
0
9
-
2
-
3
-
1
0
B
.
M
O
T
.
S
T
A
R
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

3
0
d
e
f
:

1
0
9
-
2
-
3
-
1
1
W
.

R
E
G

O
U
T
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
0
9
-
2
-
3
-
1
2
S
M
O
K
E

H
I
.
A
L
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

6
0
d
e
f
:

2
0
9
-
2
-
3
-
1
3
T
E
M
P

H
I
.
A
L
.
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
5
9
-
2
-
3
-
1
4
T
E
M
P
.
H
I
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
1
5
K
E
Y

H
O
L
D
N

S
E
C
p
w
:
s
u
l
o
:

6
0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
1
6
A
I
R

F
L
O
W

L
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

3
0
d
e
f
:

5
9
-
2
-
3
-
1
7
C
I
R
C

L
O
.
F
L
O
W
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
1
8
B
O
O
S
T
.
M
.
S
T
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
0
d
e
f
:

1
0
9
-
2
-
3
-
1
9
L
.

C
O
M
B

A
I
R
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
2
0
L
O
W

A
T
M

P
R
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

5
9
-
2
-
3
-
2
1
C
U
P

C
L
E
A
N
E
R
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
0
d
e
f
:

1
2
0
9
-
2
-
3
-
2
2
E
G
B

L
O
.
L
E
N

S
E
C

l
o
:

1
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
3
-
2
3
E
G
B

H
I
.
L
E
N

S
E
C

l
o
:

1
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
3
-
2
4
O
X
Y
G
E
N
N

S
E
C
n
o
t

u
s
e
d
9
-
2
-
3
-
2
5
T
.
I
L
.
H
I
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
2
6
T
.
O
L
.
H
I
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
2
7
W
.
L
.
C
.
N
O
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

2
9
-
2
-
3
-
2
8
W
.
L
.
C
.
S
T
B
Y
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

2
9
-
2
-
3
-
2
9
D
F
.
P
R
.
H
I
.
A
L
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
S
H
A
R
E
D
9
-
2
-
3
-
0
S
A
L

H
I
.
A
L
.
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
5
9
-
2
-
3
-
1
S
A
L

H
I
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
2
O
I
L

L
O
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
3
-
P
O
W
E
R

P
A
N
E
L

1
9
-
2
-
3
-
0
F
.
O
.
P
M
P

1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
1
F
.
O
.
P
M
P

2
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
2
F
U
E
L

P
R
E
S
S
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
0
d
e
f
:

2
9
-
2
-
3
-
3
F
.
O
.
P
M
P

D
E
L
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
4
D
O

T
O

H
F
O
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
0
d
e
f
:

3
0
0
9
-
2
-
3
-
5
H
F
O

T
O

D
O
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
0
d
e
f
:

3
0
0
9
-
2
-
3
-
6
K
E
Y

T
I
M
E
O
U
T
N

S
E
C
p
w
:
c
u
l
o
:

1
5
h
i
:

1
0
0
d
e
f
:

4
5
9
-
2
-
1
-
7
F
.
W
.
P
M
P

1
N

S
E
C
n
p
9
-
2
-
1
-
8
F
.
W
.
P
M
P

2
N

S
E
C
n
p
9
-
2
-
1
-
9
F
.
W
.

D
E
L
A
Y
N

S
E
C
n
p
9
-
2
-
1
-
1
0
F
.
W
.

M
.

R
U
N
N

S
E
C
n
p
9
-
2
-
1
-
1
1
F
.
W
.

D
E
L
A
Y
2
N

S
E
C
n
p
9
-
2
-
1
-
1
2
C
.
P
U
M
P

1
N

S
E
C
n
p
9
1
3
C
.
P
U
M
P

2
N

S
E
C
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

8

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-10 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
1
4
H
I

O
I
L

P
R
S
N

S
E
C
n
p
9
-
2
-
1
-
1
5
F
.
W
.
P
M
P

5
N

S
E
C
n
p
9
-
2
-
1
-
1
6
F
.
W
.
P
M
P

6
N

S
E
C
n
p
9
1
7
W
.
L
.
C

N
O

E
G
B
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

2
9
1
8
W
.
L
.
C

S
T
B
Y

E
G
B
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

2
9
1
9
W
.

R
E
G

O
U
T

E
G
B
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
0
9
2
0
A
U
X

P
M
P

S
T
A
R
T
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
2
1
A
U
X

P
M
P

D
E
L
A
Y
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
0
9
2
2
F
.
O
.
P
R
E
.
S
H
T
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

6
0
d
e
f
:

3
9
-
2
-
3
-
P
O
W
E
R

P
A
N
E
L

2
9
-
2
-
3
-
0
F
.
W
.
P
M
P

1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
1
F
.
W
.
P
M
P

2
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
2
F
.
W
.
P
M
P

3
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
3
F
.
W
.
P
M
P

4
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
4
F
.
W
.

D
E
L
A
Y
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
5
F
.
W
.

M
.

R
U
N
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
6
F
.
W
.

D
E
L
A
Y
2
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
3
-
7
C
.
P
U
M
P

1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
8
C
.
P
U
M
P

2
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
3
-
C
O
M
M
U
N
I
C
A
T
I
O
N
9
-
2
-
3
-
0
P
A
N
E
L
1

O
F
F
L
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

3
0
d
e
f
:

1
0
9
-
2
-
3
-
1
P
A
N
E
L
2

O
F
F
L
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

3
0
d
e
f
:

1
0
9
-
2
-
3
-
2
P
A
R
T
N
E
R

O
F
F
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:


3
0
d
e
f
:

1
0
9
-
2
-
4
E
G
B

P
A
N
E
L

T
I
M
E
R
S
n
p
9
-
2
-
4
-
0
K
E
Y

T
I
M
E

O
U
T
N

S
E
C
p
w
:
c
u
l
o
:

1
5
h
i
:

1
0
0
d
e
f
:

4
5
9
-
2
-
4
-
1
K
E
Y

H
O
L
D
N

S
E
C
p
w
:
s
u
l
o
:

6
0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
4
-
2
W
.

R
E
G

O
U
T
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

3
0
9
-
2
-
4
-
3
F
.
W
.
P
M
P

1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
4
F
.
W
.
P
M
P

2
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
5
F
.
W
.
P
M
P

3
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
6
F
.
W
.
P
M
P

4
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
7
F
.
W
.

D
E
L
A
Y
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
4
-
8
F
.
W
.

M
.

R
U
N
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
4
-
9
F
.
W
.

D
E
L
A
Y
2
N

S
E
C
p
w
:
s
u
l
o
:

1
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
2
-
4
-
1
0
C
.
P
U
M
P

1
N

S
E
C
p
w
:
c
u
l
o
:

1
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
1
1
C
.
P
U
M
P

2
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

1
5
9
-
2
-
4
-
1
2
W
A
T
E
R

H
I
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
4
-
1
3
W
A
T
E
R

H
I
.
A
L
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
4
-
1
4
W
A
T
E
R

L
O
.
A
L
N

S
E
C
p
w
:
s
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
4
-
1
5
W
A
T
E
R

L
O
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

1
2
0
d
e
f
:

5
9
-
2
-
4
-
1
6
W
A
T
E
R

S
W

L
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

0
9
-
2
-
4
-
1
7
T
.
I
L
.
H
I
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
1
8
T
.
I
L
.
H
I
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
1
9
T
.
I
L
.
L
O
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
0
T
.
I
L
.
L
O
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
1
T
.
O
L
.
H
I
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
2
T
.
O
L
.
H
I
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
3
T
.
O
L
.
L
O
.
A
L
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
4
T
.
O
L
.
L
O
.
S
D
.
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
5
D
F
.
P
R
.
H
I
.
A
L
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
6
D
F
.
P
R
.
H
I
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
7
D
F
.
P
R
.
L
O
.
A
L
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
8
D
F
.
P
R
.
L
O
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
2
9
M
E
.
L
O
.
H
I
.
A
L
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
3
0
M
E
.
L
O
.
H
I
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
3
1
M
E
.
L
O
.
L
O
.
A
L
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
3
2
M
E
.
L
O
.
L
O
.
S
D
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
9
-
2
-
4
-
3
2
M
E

S
L
O
W

D
O
W
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

1
0
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

9

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-11 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
2
-
4
-
3
3
C
I
R
C

L
O
.
F
L
O
N

S
E
C
p
w
:
c
u
l
o
:

0
h
i
:

6
0
d
e
f
:

3
9
-
2
-
5
-
D
A
T
E
/
T
I
M
E
9
-
2
-
5
-
H
O
U
R
N
p
w
:
n
o
l
o
:

0
h
i
:

2
3
d
e
f
:

0
9
-
2
-
5
-
M
I
N
N
p
w
:
n
o
l
o
:

0
h
i
:

5
9
d
e
f
:

0
9
-
2
-
5
-
S
E
C
N
p
w
:
n
o
l
o
:

0
h
i
:

5
9
d
e
f
:

0
9
-
2
-
5
-
D
A
Y
N
p
w
:
n
o
l
o
:

1
h
i
:

3
1
d
e
f
:

0
9
-
2
-
5
-
M
O
N
T
H
N
p
w
:
n
o
l
o
:

1
h
i
:

1
2
d
e
f
:

0
9
-
2
-
5
-
Y
E
A
R
N
p
w
:
n
o
l
o
:

1
9
9
2
h
i
:

2
0
9
1
d
e
f
:

0
9
-
2
-
6
H
O
U
R
/
S
T
A
R
T

C
N
T
9
-
2
-
6
-
N
O
Z
Z
L
E

1
9
-
2
-
6
-
N
O
Z
Z
L
E

1
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
N
O
Z
Z
L
E

2
9
-
2
-
6
-
N
O
Z
Z
L
E

2
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
L
O
A
D

>
2
5
%
9
-
2
-
6
-
L
O
A
D

>
2
5
%
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
L
O
A
D

>
5
0
%
9
-
2
-
6
-
L
O
A
D

>
5
0
%
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
L
O
A
D

>
7
5
%
9
-
2
-
6
-
L
O
A
D

>
7
5
%
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
L
O
A
D
9
-
2
-
6
-
L
O
A
D
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
M
O
K
E

B
L
O
W
9
-
2
-
6
-
S
M
O
K
E

B
L
O
W
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
B
O
O
S
T

P
U
M
P
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
0

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-12 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
2
-
6
-
B
O
O
S
T

P
U
M
P
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
C
O
M
B
U
S
T
.
F
A
N
9
-
2
-
6
-
C
O
M
B
U
S
T
.
F
A
N
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
B
U
R
N
.
M
O
T
O
R
9
-
2
-
6
-
B
U
R
N
.
M
O
T
O
R
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
I
G
N
I
.
M
O
T
O
R
9
-
2
-
6
-
I
G
N
I
.
M
O
T
O
R
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
U
E
L

P
U
M
P

1
9
-
2
-
6
-
F
U
E
L

P
U
M
P

1
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
U
E
L

P
U
M
P

2
9
-
2
-
6
-
F
U
E
L

P
U
M
P

2
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
C
I
R
C
.
P
U
M
P

1
9
-
2
-
6
-
C
I
R
C
.
P
U
M
P

1
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
C
I
R
C
.
P
U
M
P

2
9
-
2
-
6
-
C
I
R
C
.
P
U
M
P

2
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
1

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-13 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
C
H
E
M
.
P
U
M
P

1
9
-
2
-
6
-
C
H
E
M
.
P
U
M
P

1
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
C
H
E
M
.
P
U
M
P

2
9
-
2
-
6
-
C
H
E
M
.
P
U
M
P

2
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

1
9
-
2
-
6
-
F
.
W
.

P
U
M
P

1
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

2
9
-
2
-
6
-
F
.
W
.

P
U
M
P

2
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

3
9
-
2
-
6
-
F
.
W
.

P
U
M
P

3
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

4
9
-
2
-
6
-
F
.
W
.

P
U
M
P

4
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

5
9
-
2
-
6
-
F
.
W
.

P
U
M
P

5
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
2

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-14 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
F
.
W
.

P
U
M
P

6
9
-
2
-
6
-
F
.
W
.

P
U
M
P

6
9
-
2
-
6
-
T
O
T
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
H
O
U
R
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
2
-
6
-
T
O
T
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
S
T
A
R
T
N
p
w
:
s
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
3
S
E
T
T
I
N
G
S
9
-
3
-
1
S
T
A
R
T
/
S
T
O
P

L
I
M
I
T
S
9
-
3
-
1
-
M
.
S
T
A
R
T

D
I
F

L
O
W
N

B
A
R
p
w
:
n
o
l
o
:

0
h
i
:

2
7
d
e
f
:

0
.
2
9
-
3
M
.
S
T
A
R
T

D
I
F

H
I
G
H
N

B
A
R
p
w
:
n
o
l
o
:

0
h
i
:

2
7
d
e
f
:

0
.
7
9
-
3
-
1
-
M
.
S
T
O
P

D
I
F
F

L
O
W
N

B
A
R
p
w
:
n
o
l
o
:

0
h
i
:

2
7
d
e
f
:

2
9
-
3
M
.
S
T
O
P

D
I
F
F

H
I
G
H
N

B
A
R
p
w
:
n
o
l
o
:

0
h
i
:

2
7
d
e
f
:

7
9
-
3
-
1
-
S
L
V

M
.
S
T
A
R
T
N

B
A
R
p
w
:
n
o
l
o
:

-
2
7
h
i
:

1
0
d
e
f
:

-
2
9
-
3
D
I
F
F

H
I
G
H
N

B
A
R
p
w
:
n
o
l
o
:

-
2
7
h
i
:

1
0
d
e
f
:

-
2
9
-
3
-
1
-
S
L
V

M
.
S
T
O
P
N

B
A
R
p
w
:
n
o
l
o
:

-
2
7
h
i
:

1
0
d
e
f
:

-
0
.
5
9
-
3
D
I
F
F

H
I
G
H
N

B
A
R
p
w
:
n
o
l
o
:

-
2
7
h
i
:

1
0
d
e
f
:

-
0
.
5
9
-
3
-
1
-
S
L
A
V
E

S
T
A
R
T
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
5
9
-
3
-
1
-
S
L
A
V
E

S
T
O
P
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
5
9
-
3
-
1
-
S
T
A
R
T

S
L
A
V
E
N

S
E
C
p
w
:
n
o
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
3
-
1
-
S
T
O
P

S
L
A
V
E
N

S
E
C
p
w
:
n
o
l
o
:

0
h
i
:

3
6
0
0
d
e
f
:

6
0
9
-
3
-
2
M
I
N
.
F
I
R
I
N
G

9
-
3
-
2
-
A
I
R

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
A
I
R

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
O
I
L

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
A
I
R

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
O
I
L

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
S
E
R
V
O

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
0
9
-
3
-
3
P
U
R
G
E

P
O
S
I
T
I
O
N
9
-
3
-
3
-
A
I
R

P
O
S
.
N

%
p
w
:
s
u
l
o
:

5
0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
3
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
3
-
A
I
R

S
E
R
V
O
N

%
p
w
:
s
u
l
o
:

5
0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
3
-
O
I
L

S
E
R
V
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
3
-
S
E
R
V
O

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
4
I
G
N
I
T
I
O
N

P
O
S
I
T
I
O
N
9
-
3
-
4
-
A
I
R

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
A
I
R

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
O
I
L

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
A
I
R

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
O
I
L

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
4
-
S
E
R
V
O

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
0
9
-
3
-
5
S
E
R
V
O

P
O
S
9
-
3
-
5
-
P
O
S

N
O
Z
Z
L

1
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
0
9
-
3
-
5
-
P
O
S

2

O
P
E
N
G
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
5
9
-
3
-
5
-
P
O
S

1

A
N
D

2
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
5
9
-
3
-
6
R
I
S
I
N
G
9
-
3
-
6
-
W
A
R
M

U
P

L
I
M
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

2
9
-
3
-
6
-
R
I
S
I
N
G

D
I
F
F
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

1
9
-
3
-
6
-
M
O
D
.
F
R
.
D
I
F
F
N

B
A
R
p
w
:
c
u
l
o
:

0
h
i
:

2
7
d
e
f
:

1
9
-
3
-
7
S
T
E
A
M

P
U
R
G
E

9
-
3
-
7
P
O
S
T

P
U
R
G
E
9
-
3
-
7
-
A
I
R

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
5
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
3

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-15 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
3
-
7
-
O
I
L

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
7
-
A
I
R

S
E
R
V
O
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
5
9
-
3
-
7
-
O
I
L

S
E
R
V
O
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
8
S
T
A
N
D

B
Y

P
O
S
I
T
I
O
N
9
-
3
-
8
-
A
I
R

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
8
-
O
I
L

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
8
-
A
I
R

S
E
R
V
O
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
8
-
O
I
L

S
E
R
V
O
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
9
O
I
L

-

A
I
R

R
A
T
I
O
9
-
3
O
I
L

-

A
I
R

R
A
T
I
O

H
F
O
9
-
3
-
9
-
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
9
-
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
9
-
3
-
9
-
1
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
9
-
3
-
9
-
1
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
9
-
2
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
0
9
-
3
-
9
-
2
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
5
9
-
3
-
9
-
3
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
0
9
-
3
-
9
-
3
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
5
9
-
3
-
9
-
4
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
9
-
3
-
9
-
4
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
5
9
-
3
-
9
-
5
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
0
9
-
3
-
9
-
5
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
5
9
-
3
-
9
-
6
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
0
9
-
3
-
9
-
6
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
5
9
-
3
-
9
-
7
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
9
-
7
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
5
9
-
3
-
9
-
8
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

8
0
9
-
3
-
9
-
8
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

8
5
9
-
3
-
9
-
9
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

9
0
9
-
3
-
9
-
9
5
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

9
5
9
-
3
-
9
-
1
0
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
3
C
O
R
R
.
F
A
C
T
O
R
N

%
p
w
:
c
u
l
o
:

5
0
h
i
:

1
5
0
d
e
f
:

1
0
0
9
-
3
O
I
L

-

A
I
R

R
A
T
I
O

D
O
9
-
3
-
9
-
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
9
-
1
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
9
-
3
-
9
-
2
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
0
9
-
3
-
9
-
3
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

3
0
9
-
3
-
9
-
4
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
9
-
3
-
9
-
5
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

5
0
9
-
3
-
9
-
6
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
0
9
-
3
-
9
-
7
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
9
-
8
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

8
0
9
-
3
-
9
-
9
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

9
0
9
-
3
-
9
-
1
0
0
%
O
I
L
-
A
I
R
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
3
C
O
R
R
.
F
A
C
T
O
R
N

%
p
w
:
c
u
l
o
:

5
0
h
i
:

1
5
0
d
e
f
:

1
0
0
9
-
3
-
1
0
O
I
L

-

A
T
O
M
I
Z
I
N
G

9
-
3
-
1
0
-
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

2
9
-
3
-
1
0
-
1
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

3
9
-
3
-
1
0
-
2
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

3
.
5
9
-
3
-
1
0
-
3
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

4
9
-
3
-
1
0
-
4
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

4
.
5
9
-
3
-
1
0
-
5
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

5
9
-
3
-
1
0
-
6
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

5
.
5
9
-
3
-
1
0
-
7
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

6
9
-
3
-
1
0
-
8
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

6
9
-
3
-
1
0
-
9
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

6
9
-
3
-
1
0
-
1
0
0
%
O
I
L
-
A
T
Z
N

B
A
R
p
w
:
n
o
l
o
:

2
h
i
:

1
2
d
e
f
:

6
9
-
3
-
1
1
O
I
L

O
U
T
/
I
N

M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
4

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-16 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
3
-
1
1
-
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
1
1
-
1
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
.
2
9
-
3
-
1
1
-
2
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
.
5
9
-
3
-
1
1
-
3
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
.
6
9
-
3
-
1
1
-
4
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

9
.
9
9
-
3
-
1
1
-
5
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
4
.
3
9
-
3
-
1
1
-
6
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
1
.
1
9
-
3
-
1
1
-
7
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
9
.
8
9
-
3
-
1
1
-
8
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
6
.
9
9
-
3
-
1
1
-
9
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
7
.
9
9
-
3
-
1
1
-
1
0
0
%
O
I
L

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
3
-
1
2
A
I
R

O
U
T
/
I
N

9
-
3
-
1
2
-
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
3
-
1
2
-
1
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
.
1
9
-
3
-
1
2
-
2
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
.
5
9
-
3
-
1
2
-
3
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
.
6
9
-
3
-
1
2
-
4
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

9
.
9
9
-
3
-
1
2
-
5
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
4
.
3
9
-
3
-
1
2
-
6
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
1
.
1
9
-
3
-
1
2
-
7
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
9
.
8
9
-
3
-
1
2
-
8
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
6
.
9
9
-
3
-
1
2
-
9
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
7
.
9
9
-
3
-
1
2
-
1
0
0
%
A
I
R

O
U
T
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
3
-
2
M
A
X
.
F
I
R
I
N
G

9
-
3
-
2
-
A
I
R

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
O
I
L

D
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
A
I
R

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
2
-
O
I
L

H
F
O
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
3
M
I
N
.
F
I
R
I
N
G

(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

9
-
3
-
1
3
-
A
I
R

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
3
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
4
M
A
X
.
F
I
R
I
N
G

(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

9
-
3
-
1
4
-
M
A
X

L
O
A
D
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
3
-
1
5
P
U
R
G
E

P
O
S
I
T
I
O
N

(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

9
-
3
-
1
5
-
A
I
R

P
O
S
.
N

%
p
w
:
s
u
l
o
:

2
0
h
i
:

1
0
0
d
e
f
:

7
0
9
-
3
-
1
5
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
6
I
G
N
I
T
I
O
N

P
O
S
I
T
I
O
N

(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

9
-
3
-
1
6
-
A
I
R

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
6
-
O
I
L

P
O
S
.
N

%
p
w
:
n
o
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
3
-
1
7
S
T
M
.
P
U
R
G
E

(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

9
-
3
-
1
7
-
A
I
R

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

2
5
9
-
3
-
1
7
-
O
I
L

P
O
S
.
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
5
9
-
4
D
I
A
G
N
O
S
E
S
9
-
4
-
1
S
O
F
T
W
A
R
E

V
E
R
S
I
O
N
n
p
9
-
4
-
1
-
[
P
A
N
E
L

T
Y
P
E
]
N
n
p
9
-
4
-
1
-
[
V
E
R
S
I
O
N
]
N
n
p
9
-
4
-
1
-
[
I
N
F
O

1
]
N
n
p
9
-
4
-
1
-
[
I
N
F
O

2
]
N
n
p
9
-
4
-
2
D
I
G
I
T
A
L

I
N
P
U
T
n
p
9
-
4
-
2
-
E
X
T
E
R
N

S
H
U
T
D
O
W
N


















N
n
p
9
-
4
-
2
-
H
I

S
T
M

P
R
E
S
S

S
W
I
T
C
H






















N
n
p
9
-
4
-
2
-
L
A
N
C
E

R
E
D
R
A
W
N


























N
n
p
9
-
4
-
2
-
B
U
R
N
E
R

S
W
I
N
G

O
U
T




















N
n
p
9
-
4
-
2
-
W
A
T
E
R

L
E
V
E
L

L
O
W































N
n
p
9
-
4
-
2
-
F
L
A
M
E

S
C
A
N
N
E
R

1




































N
n
p
9
-
4
-
2
-
F
L
A
M
E

S
C
A
N
N
E
R

2



































N
n
p
9
-
4
-
2
-
S
T
A
R
T

P
E
R
.

F
R
O
M

P
M
S


























N
n
p
9
-
4
-
2
-
I
G
N
I
T
E
R

I
N
S
E
R
T
E
D



































N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
5

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-17 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
4
-
2
-
A
I
R

F
A
N

C
L
O
S
E
D





















N
n
p
9
-
4
-
2
H
F
O

D
O

P
O
S
I
T
I
O
N
N
n
p
9
-
4
-
2
O
I
L

V
L
V
.

I
N

P
O
S
I
T
I
O
N






























N
n
p
9
-
4
-
2
-
Q
U
I
C
K

C
L
O
S
I
N
G

V
A
L
V
E
































N
n
p
9
-
4
-
2
H
I
.

O
I
L

P
R
E
S
S

R
E
T
U
R
N


























N
n
p
9
-
4
-
2
-
I
G
N
.

F
L
A
M
E

S
U
R
V
.
























N
n
p
9
-
4
-
2
F
I
R
E

I
N

W
I
N
D
B
O
X




































N
n
p
9
-
4
-
2
-
H
I
G
H

T
E
M
P










































N
n
p
9
-
4
-
2
-
L
O
W

C
O
M
B

A
I
R

P
R
E
S
S

































N
n
p
9
-
4
-
2
-
L
O
W

O
I
L

P
R
S
S

N
O
Z
Z
L
E































N
n
p
9
-
4
-
2
-
H
I
.
O
I
L

T
E
M
P

S
W

I
N

P
R
E






















N
n
p
9
-
4
-
2
-
L
O
W

O
I
L

T
E
M
P

N
O
Z
Z
L
E
































N
n
p
9
-
4
-
2
-
L
O
W

A
T
M

P
R
E
S
S






































N
n
p
9
-
4
-
2
-
C
O
L
D

W
A
R
M

S
T
A
R
T




































N
n
p
9
-
4
-
2
-
I
N
E
R
T

G
A
S










































N
n
p
9
-
4
-
2
E
X
T
E
R
N

S
T
O
P








































N
n
p
9
-
4
-
2
S
M
A
L
L

G
U
N










































N
n
p
9
-
4
-
2
B
U
R
N
E
R

M
O
T
O
R

1

F
B




























N
n
p
9
-
4
-
2
B
U
R
N
E
R

M
O
T
O
R

1

O
L




























N
n
p
9
-
4
-
2
C
O
M
B

A
I
R

F
A
N

1

F
B
























N
n
p
9
-
4
-
2
B
O
O
S
T
E
R

P
U
M
P

F
B





















N
n
p
9
-
4
-
2
C
O
M
B

A
I
R

F
A
N

1

O
L
























N
n
p
9
-
4
-
2
E
X
T
E
R
N

S
T
O
P

2






































N
n
p
9
-
4
-
2
E
X
T
E
R
N

S
H
U
T
D
O
W
N

2
N
n
p
9
-
4
-
2
-
9
-
4
-
2
C
I
R
C
.
P
M
P

1

L
F
N
n
p
9
-
4
-
2
-
H
E
A
V
Y

F
U
E
L

O
P
E
R
A
T
I
O
N
N
n
p
9
-
4
-
2
-
F
U
E
L

P
U
M
P
1

F
B
N
n
p
9
-
4
-
2
-
F
U
E
L

P
U
M
P
2

F
B
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

1

F
B
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

2

F
B
N
n
p
9
-
4
-
2
-
C
O
M
B

A
I
R

F
A
N

1

F
B
N
n
p
9
-
4
-
2
-
H
O
T
W
E
L
L

L
O
W

S
T
O
P

P
U
M
P
S
N
n
p
9
-
4
-
2
-
C
O
M
B

A
I
R

F
A
N

1

O
L
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

1

S
T
B
Y
N
n
p
9
-
4
-
2
-
C
O
M
B

A
I
R

F
A
N

2

F
B
N
n
p
9
-
4
-
2
-
A
U
X
I
L
L
A
R
Y

P
U
M
P

F
B
N
n
p
9
-
4
-
2
-
C
O
M
B

A
I
R

F
A
N

2

O
L
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
B
Y
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

F
B
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

2

F
B
N
n
p
9
-
4
-
2
S
A
L
I
N
I
T
Y
N
n
p
9
-
4
-
2
O
I
L

C
O
N
T
E
N
T
N
n
p
9
-
4
-
2
H
I
.

S
T
E
A
M

X
S
2
V
N
n
p
9
-
4
-
2
H
I
G
H

G
A
S

T
E
M
P

A
T

E
G
B
N
n
p
9
-
4
-
2
F
.
O
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
O
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
F
.
O
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
O
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
9
-
4
-
2
-
F
.
W
.
P
M
P

1

F
B
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P

1

S
T
B
Y
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P

2

F
B
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P

2

S
T
B
Y
N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
6

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-18 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
4
-
2
F
.
W
.
P
M
P

3

F
B
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

3

S
T
B
Y
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

4

F
B
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P

4

S
T
B
Y
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

F
B
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
B
Y
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

L
F
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

2

F
B
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
O
P
N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
A
R
T

N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
O
P

N
n
p
9
-
4
-
2
C
I
R
C
.
P
M
P

1

S
T
A
R
T

N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
1

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
1

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
2

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
2

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
F
.
W
.
P
M
P
3

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P
3

R
E
M

S
T
A
R
T
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P
4

R
E
M

S
T
O
P
N
n
p
9
-
4
-
2
-
F
.
W
.
P
M
P
4

R
E
M
S
T
A
R
T
N
n
p
9
-
4
-
2
-
9
-
4
3
D
I
G
I
T
A
L

O
U
T
P
U
T
9
-
4
3
A
T
M

S
T
E
A
M

P
R
S
.

U
P
N
n
p
9
-
4
3
S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
O
I
L

S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
A
T
M

S
T
E
A
M

P
R
S
.

D
W
N
n
p
9
-
4
3
S
E
R
V
O

M
O
T
O
R

D
O
W
N
N
n
p
9
-
4
3
O
I
L

S
E
R
V
O

M
O
T
O
R

D
W
N
n
p
9
-
4
3
I
G
N
I
T
I
O
N
N
n
p
9
-
4
3
B
U
R
N
E
R

M
O
T
O
R

1
N
n
p
9
-
4
3
W
A
T
E
R

L
E
V
E
L

M
A
N

A
U
T
O
N
n
p
9
-
4
3
O
I
L
N
n
p
9
-
4
3
N
O
Z
Z
L
E
1
N
n
p
9
-
4
3
A
T
M

S
T
E
A
M
N
n
p
9
-
4
3
S
A
F
E
T
Y

V
A
L
V
E
N
n
p
9
-
4
3
I
G
N
I
T
I
O
N

P
U
R
G
E

V
L
V
N
n
p
9
-
4
3
S
T
E
A
M

P
U
R
G
E
N
n
p
9
-
4
3
H
E
A
T
I
N
G

E
L
E
M
E
N
T
N
n
p
9
-
4
3
O
U
T

S
E
T
P
N
n
p
9
-
4
3
N
O
Z
Z
L
E
2
N
n
p
9
-
4
3
F
U
E
L

O
I
L

B
O
O
S
T
E
R

P
.
N
n
p
9
-
4
3
A
I
R

S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
S
O
O
T
B
L
O
W
E
R
N
n
p
9
-
4
3
A
I
R

S
E
R
V
O

M
O
T
O
R

D
W
N
n
p
9
-
4
3
W
.

L
E
V
E
L

M
A
N

I
N
C
.
N
n
p
9
-
4
3
F
U
E
L

H
E
A
T
E
R
N
n
p
9
-
4
3
W
.

L
E
V
E
L

M
A
N

D
E
C
.
N
n
p
9
-
4
3
S
M
O
K
E

D
E
N
S
I
T
Y

1
N
n
p
9
-
4
3
A
L
A
R
M
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
1
N
n
p
9
-
4
3
S
T
A
R
T

R
E
Q
.

T
O

P
M
S
N
n
p
9
-
4
3
W
A
R
N
I
N
G
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
2
N
n
p
9
-
4
3
H
I
G
H

W
A
T
E
R

L
E
V
E
L
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
3
N
n
p
9
-
4
3
L
O
W

W
A
T
E
R

L
E
V
E
L
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
4
N
n
p
9
-
4
3
B
U
R
N
E
R

I
N

S
T
O
P
N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
7

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-19 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
4
3
F
E
E
D

W
A
T
E
R

R
E
G

1
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

R
E
G

2
N
n
p
9
-
4
3
9
-
4
3
F
U
E
L

P
U
M
P
1
N
n
p
9
-
4
3
F
U
E
L

P
U
M
P
2
N
n
p
9
-
4
3
F
U
E
L

O
I
L

P
R
E
S
S

U
P
N
n
p
9
-
4
3
F
U
E
L

O
I
L

P
R
E
S
S

D
W
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

P
U
M
P
1
N
n
p
9
-
4
3
F
U
E
L

O
I
L

T
E
M
P

U
P
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

P
U
M
P
2
N
n
p
9
-
4
3
F
U
E
L

O
I
L

T
E
M
P

D
W
N
n
p
9
-
4
3
S
M
O
K
E

D
E
N
S
I
T
Y

1
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

S
T
B
Y
N
n
p
9
-
4
3
S
M
O
K
E

D
E
N
S
I
T
Y

2
N
n
p
9
-
4
3
C
I
R
C

P
U
M
P

S
T
B
Y
N
n
p
9
-
4
3
H
E
A
T
I
N
G

1
N
n
p
9
-
4
3
C
I
R
C
.

P
U
M
P
1

S
T
A
R
T
N
n
p
9
-
4
3
H
E
A
T
I
N
G

2
N
n
p
9
-
4
3
C
I
R
C
.

P
U
M
P
2

S
T
A
R
T
N
n
p
9
-
4
3
F
U
E
L

P
M
P

S
T
B

S
T
N
n
p
9
-
4
3
O
I
L

V
L
V

R
E
T
U
R
N

L
I
N
E
N
n
p
9
-
4
-
3
-
S
T
A
R
T

C
O
M
B

A
I
R

F
A
N

1
N
n
p
9
-
4
-
3
-
F
U
E
L

O
I
L

T
E
M
P

U
P
N
n
p
9
-
4
-
3
-
F
U
E
L

O
I
L

T
E
M
P

D
W
N
n
p
9
-
4
-
3
-
S
T
A
R
T

C
O
M
B

A
I
R

F
A
N
2 N
n
p
9
-
4
-
3
-
C
H
E
M
I
C
A
L

S
T
A
T
I
O
N
1
N
n
p
9
-
4
-
3
-
C
H
E
M
I
C
A
L

S
T
A
T
I
O
N
2
N
n
p
9
-
4
3
A
U
X

S
T
A
R
T
N
n
p
9
-
4
-
3
-
9
-
4
-
3
-
F
E
E
D

W
A
T
E
R

P
U
M
P
1
N
n
p
9
-
4
-
3
-
F
E
E
D

W
A
T
E
R

P
U
M
P
2
N
n
p
9
-
4
-
3
-
F
E
E
D

W
A
T
E
R

P
U
M
P
3
N
n
p
9
-
4
-
3
-
F
E
E
D

W
A
T
E
R

P
U
M
P
4
N
n
p
9
-
4
-
3
-
C
I
R
C
.

P
U
M
P
1

S
T
A
R
T
N
n
p
9
-
4
-
3
-
C
I
R
C
.

P
U
M
P
2

S
T
A
R
T
N
n
p
9
-
4
-
3
-
F
E
E
D

W
A
T
E
R

S
T
B
Y
N
n
p
9
-
4
-
3
-
C
I
R
C

P
U
M
P

S
T
B
Y
N
n
p
9
-
4
-
3
-
9
-
4
-
4
S
U
P
E
R
U
S
E
R

n
p
9
-
4
-
4
-
[
U
S
E
D
]
N
n
p
9
-
4
-
5
S
E
R
I
A
L

N
U
M
B
E
R
n
p
9
-
4
-
5
-
S
E
R
I
A
L

N
O
N
p
w
:
c
u
9
-
4
-
5
-
C
O
M
M
I
S
S
I
O
N
E
D
N
n
p
9
-
4
-
5
-
E
R
A
S
E

E
E
P
R
O
M
N
p
w
:
c
u
9
-
4
-
6
N
O

O
F

S
H
T
.
D
W
N
.
n
p
9
-
4
-
6
-
N
O

O
F

S
H
T
.
D
W
N
.
N
n
p
9
-
4
3
D
I
G
I
T
A
L

O
U
T
P
U
T

9
-
4
3
A
T
M

S
T
E
A
M

P
R
S
.

U
P
N
n
p
9
-
4
3
S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
O
I
L

S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
A
T
M

S
T
E
A
M

P
R
S
.

D
W
N
n
p
9
-
4
3
S
E
R
V
O

M
O
T
O
R

D
O
W
N
N
n
p
9
-
4
3
O
I
L

S
E
R
V
O

M
O
T
O
R

D
W
N
n
p
9
-
4
3
I
G
N
I
T
I
O
N
N
n
p
9
-
4
3
B
U
R
N
E
R

M
O
T
O
R

1
N
n
p
9
-
4
3
W
A
T
E
R

L
E
V
E
L

M
A
N

A
U
T
O
N
n
p
9
-
4
3
O
I
L
N
n
p
9
-
4
3
N
O
Z
Z
L
E
1
N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
8

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-20 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
4
3
A
T
M

S
T
E
A
M
N
n
p
9
-
4
3
S
A
F
E
T
Y

V
A
L
V
E
N
n
p
9
-
4
3
I
G
N
I
T
I
O
N

P
U
R
G
E

V
L
V
N
n
p
9
-
4
3
S
T
E
A
M

P
U
R
G
E
N
n
p
9
-
4
3
H
E
A
T
I
N
G

E
L
E
M
E
N
T
N
n
p
9
-
4
3
O
U
T

S
E
T
P
N
n
p
9
-
4
3
N
O
Z
Z
L
E
2
N
n
p
9
-
4
3
F
U
E
L

O
I
L

B
O
O
S
T
E
R

P
.
N
n
p
9
-
4
3
A
I
R

S
E
R
V
O

M
O
T
O
R

U
P
N
n
p
9
-
4
3
S
O
O
T
B
L
O
W
E
R
N
n
p
9
-
4
3
A
I
R

S
E
R
V
O

M
O
T
O
R

D
W
N
n
p
9
-
4
3
W
.

L
E
V
E
L

M
A
N

I
N
C
.
N
n
p
9
-
4
3
F
U
E
L

H
E
A
T
E
R
N
n
p
9
-
4
3
W
.

L
E
V
E
L

M
A
N

D
E
C
.
N
n
p
9
-
4
3
S
M
O
K
E

D
E
N
S
I
T
Y

1
N
n
p
9
-
4
3
A
L
A
R
M
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
1
N
n
p
9
-
4
3
S
T
A
R
T

R
E
Q
.

T
O

P
M
S
N
n
p
9
-
4
3
W
A
R
N
I
N
G
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
2
N
n
p
9
-
4
3
H
I
G
H

W
A
T
E
R

L
E
V
E
L
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
3
N
n
p
9
-
4
3
L
O
W

W
A
T
E
R

L
E
V
E
L
N
n
p
9
-
4
3
A
L
A
R
M

G
R
.
4
N
n
p
9
-
4
3
B
U
R
N
E
R

I
N

S
T
O
P
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

R
E
G

1
N
n
p
9
-
4
3
F
E
E
D

W
A
T
E
R

R
E
G

2
N
n
p
9
-
4
3
9
-
4
-
8
N
E
W

P
A
S
S
W
O
R
D
9
-
4
-
8
-
N
E
W

P
A
S
S
W
O
R
D
N
p
w
:
c
u
9
-
4
-
8
-
R
E
S
E
T

P
A
S
S
W
O
R
D
S
N
p
w
:
s
p
e
c
i
a
l
9
-
4
-
9
C
O
N
T
R
O
L
L
E
R
S
n
p
9
-
4
-
9
-
A
I
R

F
L
O
W
[
S
E
T
.
P
]
[
V
A
L
U
E
]
N
n
p
9
-
4
-
9
-
F
.
O
.

F
L
[
S
E
T
.
P
]
[
V
A
L
U
E
]
N
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
L
O
A
D
%
]
N
n
p
-
-
-
-
-
-
[
S
T
A
T
E
]
[
M
O
D
E
]
[
L
O
A
D
N
n
p
9
-
5
L
O
G
G
I
N
G
S
9
-
5
-
1
I
N
S
P
E
C
T

S
H
T
.
D
W
N
.

n
p
9
-
5
-
1
-
[
S
H
T
.
D
W
N
.

N
U
M
]
N
n
p
9
-
5
-
1
-
[
S
H
T
.
D
W
N
.

T
E
X
T
]
N
n
p
9
-
5
-
3
O
I
L

S
U
M
M
A
R
I
Z
E
R
9
-
2
-
6
-
9
-
2
-
6
-
O
I
L

F
L
O
W

N
9
-
2
-
6
-
T
O
T
A
L
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
E
R
V
I
C
E
N

H
O
U
R
p
w
:
s
u
l
o
:

0
h
i
:

3
0
0
0
0
d
e
f
:

0
9
-
2
-
6
-
S
R
V
.
V
A
L
(
1
0
0
0
L
)
N

H
O
U
R
p
w
:
c
u
l
o
:

0
h
i
:

2
2
7
6
0
d
e
f
:

0
9
-
2
-
6
-
R
E
S
E
T
N
p
w
:
c
u
9
-
6
-
C
A
L
I
B
R
A
T
E
9
-
6
-
1
W
A
T
E
R

L
E
V
E
L
9
-
6
-
1
-
W
A
T
E
R

L
E
V
E
L
N

m
m
n
p
9
-
6
-
1
-
R
A
N
G
E

H
I
G
H
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

1
5
0
0
d
e
f
:

2
6
0
9
-
6
-
1
-
R
A
N
G
E

L
O
W
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

0
d
e
f
:

-
2
6
5
9
-
6
-
1
-
R
N
D
.
1
/
1
0
M
M
N
p
w
:
c
u
l
o
:

1
h
i
:

1
0
0
d
e
f
:

1
0
9
-
6
-
2
A
I
R

F
L
O
W
9
-
6
-
2
-
A
I
R

F
L
O
W
N

%
n
p
9
-
6
-
2
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

9
9
9
.
9
d
e
f
:

1
0
0
9
-
6
-
2
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
9
-
6
-
2
A
I
R

S
E
R
V
O
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

1
9

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-21 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
6
-
2
-
A
I
R

S
E
R
V
O
N

%
n
p
9
-
6
-
2
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

9
9
9
.
9
d
e
f
:

1
0
0
9
-
6
-
2
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

-
1
0
0
h
i
:

1
0
0
d
e
f
:

0
9
-
6
-
3
O
I
L

F
L
O
W
9
-
6
-
3
-
O
I
L

F
L
O
W
N

%
n
p
9
-
6
-
3
-
M
A
X

F
L
O
W
N

L
/
H
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
0
0
d
e
f
:

0
9
-
6
-
3
-
B
E
A
T
S
/
(
1
0
L
)
N
p
w
:
c
u
l
o
:

0
h
i
:

2
2
0
0
0
d
e
f
:

0
9
-
6
-
3
O
I
L

S
E
R
V
O
9
-
6
-
3
-
A
I
R

S
E
R
V
O
N

%
n
p
9
-
6
-
3
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
0
0
d
e
f
:

0
9
-
6
-
3
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

0
h
i
:

2
2
0
0
0
d
e
f
:

0
9
-
6
-
4
B
O
I
L
E
R

P
R
E
S
9
-
6
-
4
-
B
O
I
L
E
R

P
R
E
S
N

B
A
R
n
p
9
-
6
-
4
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

2
5
9
-
6
-
4
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

0
9
-
6
-
5
A
T
M
.
S
T
M
.
P
R
S
9
-
6
-
5
-
A
T
M
.
S
T
M
.
P
R
S
N

B
A
R
n
p
9
-
6
-
5
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

2
5
9
-
6
-
6
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

0
9
-
6
-
6
F
U
E
L

O
.
P
R
E
S
9
-
6
-
6
-
F
U
E
L

O
.
P
R
E
S
N

B
A
R
n
p
9
-
6
-
6
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:
4
0
9
-
6
-
6
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

3
0
d
e
f
:

0
9
-
6
-
7
F
U
E
L

O
.
T
E
M
P
9
-
6
-
7
-
F
U
E
L

O
.
T
E
M
P
N

C
n
p
9
-
6
-
7
-
R
A
N
G
E

H
I
G
H
N

C
p
w
:
c
u
l
o
:

0
h
i
:

5
0
0
d
e
f
:

1
6
0
9
-
6
-
7
-
R
A
N
G
E

L
O
W
N

C
p
w
:
c
u
l
o
:

-
2
0
0
h
i
:

2
0
0
d
e
f
:

0
9
-
6
-
8
O
X
Y
G
E
N

S
E
N
S
9
-
6
-
8
-
O
X
Y
G
E
N

S
E
N
S
N

%
n
p
9
-
6
-
8
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
9
-
6
-
8
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
6
-
9
S
M
O
K
E

D
E
N
S
.
9
-
6
-
9
-
S
M
O
K
E

D
E
N
S
.
N

%
9
-
6
-
9
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
6
-
9
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
6
-
1
0
S
A
L
I
N
I
T
Y
9
-
6
-
1
0
-
S
A
L
I
N
I
T
Y
N

p
p
m
n
p
9
-
6
-
1
0
-
R
A
N
G
E

H
I
G
H
N

p
p
m
p
w
:
c
u
l
o
:

0
h
i
:

5
0
d
e
f
:

2
0
9
-
6
-
1
0
-
R
A
N
G
E

L
O
W
N

p
p
m
p
w
:
c
u
l
o
:

0
h
i
:

5
0
d
e
f
:

0
9
-
6
-
1
1
O
.
P
R
.
N
Z
/
E
X
T
9
-
6
-
1
1
-
O
.
P
R
.
N
Z
/
E
X
T
N

B
A
R

o
r

%
n
p
9
-
6
-
1
1
-
R
A
N
G
E

H
I
G
H
N

B
A
R

o
r

%
p
w
:
c
u
l
o
:

-
1
0
h
i
:

1
1
0
d
e
f
:

2
5
9
-
6
-
1
1
-
R
A
N
G
E

L
O
W
N

B
A
R

o
r

%
p
w
:
c
u
l
o
:

-
1
0
h
i
:

1
1
0
d
e
f
:

0
9
-
6
-
1
2
S
T
.
P
R
E
S
.
C
O
M
9
-
6
-
1
2
-
S
T
.
P
R
E
S
.
C
O
M
N

B
A
R
n
p
9
-
6
-
1
2
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

2
5
9
-
6
-
1
2
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

0
9
-
6
-
1
3
S
E
R
V
O

M
O
T
O
R
9
-
6
-
1
3
-
S
E
R
V
O

M
O
T
O
R
N

%
n
p
9
-
6
-
1
3
-
R
A
W

D
A
T
A
N
n
p
9
-
6
-
1
3
-
R
A
N
G
E

H
I
G
H
N
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
0
0
d
e
f
:

7
5
0
0
9
-
6
-
1
3
-
R
A
N
G
E

L
O
W
N
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
0
0
d
e
f
:

1
0
0
9
-
6
-
1
4
S
T
E
A
M

F
L
O
W
9
-
6
-
1
4
-
S
T
E
A
M

F
L
O
W
N

%
n
p
9
-
6
-
1
4
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

3
0
0
d
e
f
:

2
0
0
9
-
6
-
1
4
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

0
h
i
:

3
0
0
d
e
f
:

0
9
-
6
-
1
5
T
E
M
P
.
I
N
L
E
T
9
-
6
-
1
5
-
T
E
M
P
.
I
N
L
E
T
N

C
p
w
:
c
u
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

2
0

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-22 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
6
-
1
5
-
R
A
N
G
E

H
I
G
H
N

C
p
w
:
c
u
l
o
:

0
h
i
:

7
0
0
d
e
f
:

6
0
0
9
-
6
-
1
5
-
R
A
N
G
E

L
O
W
N

C
p
w
:
c
u
l
o
:

0
h
i
:

7
0
0
d
e
f
:

0
9
-
6
-
1
6
T
E
M
P
.

O
U
T
L
E
T
9
-
6
-
1
6
-
T
E
M
P
.
O
U
T
L
E
T
N

C
9
-
6
-
1
6
-
R
A
N
G
E

H
I
G
H
N

C
p
w
:
c
u
l
o
:

0
h
i
:

7
0
0
d
e
f
:

6
0
0
9
-
6
-
1
6
-
R
A
N
G
E

L
O
W
N

C
p
w
:
c
u
l
o
:

0
h
i
:

7
0
0
d
e
f
:

0
9
-
6
-
1
7
D
I
F
F
.
P
R
E
S
S
.
9
-
6
-
1
7
-
D
I
F
F
.
P
R
E
S
S
.
N

m
m
9
-
6
-
1
7
-
R
A
N
G
E

H
I
G
H
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

2
5
0
9
-
6
-
1
7
-
R
A
N
G
E

L
O
W
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

2
5
0
d
e
f
:

0
9
-
6
-
1
8
M
E
.

L
O
A
D
9
-
6
-
1
8
-
M
E
.
L
O
A
D
N

%
9
-
6
-
1
8
-
R
A
N
G
E

H
I
G
H
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
0
9
-
6
-
1
8
-
R
A
N
G
E

L
O
W
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

0
9
-
6
-
1
9
F
W
.
P
R
/
F
L
9
-
6
-
1
9
-
F
W
.
P
R
/
F
L
N

B
A
R
n
p
9
-
6
-
1
9
-
O
F
F
S
E
T
N

B
A
R
p
w
:

c
u
l
o
:

-
1
0
h
i
:

1
0
d
e
f
:

0
9
-
6
-
1
9
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:

c
u
l
o
:

-
1
h
i
:

3
0
0
d
e
f
:

4
0
9
-
6
-
1
9
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:

c
u
l
o
:

-
1
h
i
:

3
0
0
d
e
f
:

0
9
-
6
-
3
O
I
L

F
L
O
W
9
-
6
-
3
-
O
I
L

F
L
O
W
N

%
n
p
9
-
6
-
3
-
M
A
X

F
L
O
W
N

L
/
H
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
0
0
d
e
f
:

0
9
-
6
-
3
-
B
E
A
T
S
/
(
1
0
L
)
N
p
w
:
c
u
l
o
:

0
h
i
:

2
2
0
0
0
d
e
f
:

0
9
-
6
-
1
W
A
T
E
R

L
E
V
E
L

X
S
2
V
9
-
6
-
1
-
W
A
T
E
R

L
E
V
E
L
N

m
m
n
p
9
-
6
-
1
-
R
A
N
G
E

H
I
G
H
N

m
m
p
w
:
c
u
l
o
:

0
h
i
:

1
5
0
0
d
e
f
:

2
6
0
9
-
6
-
1
-
R
A
N
G
E

L
O
W
N

m
m
p
w
:
c
u
l
o
:

-
1
0
0
0
h
i
:

0
d
e
f
:

-
2
6
5
9
-
6
-
1
-
R
N
D
.
1
/
1
0
M
M
N
p
w
:
c
u
l
o
:

1
h
i
:

1
0
0
d
e
f
:

1
0
9
-
6
-
4
B
O
I
L
E
R

P
R
E
S

X
S
2
V
9
-
6
-
4
-
B
O
I
L
E
R

P
R
E
S
N

B
A
R
n
p
9
-
6
-
4
-
R
A
N
G
E

H
I
G
H
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

2
5
9
-
6
-
4
-
R
A
N
G
E

L
O
W
N

B
A
R
p
w
:
c
u
l
o
:

-
1
h
i
:

5
0
d
e
f
:

0
9
-
7
C
O
N
F
I
G
9
-
7
-
1
P
A
N
E
L

S
Y
S
T
E
M
9
-
7
-
1
-
P
A
N
E
L

T
Y
P
E
N
p
w
:
s
u
d
e
f
:

n
o
t

d
e
f
9
-
7
-
1
-
I
O

C
F
G
N
p
w
:
s
u
d
e
f
:

n
o
t

d
e
f
9
-
7
-
1
-
B
U
R
N
E
R

T
Y
P
E
N
p
w
:
s
u
d
e
f
:

n
o
t

d
e
f
9
-
7
-
1
-
B
U
R
N
E
R

F
A
M
I
L
Y
N
p
w
:
s
u
d
e
f
:

m
u
l
t
i
9
-
7
-
1
-
N
O
D
E

N
O
.
O
F
F
S
E
T
N
p
w
:
s
u
l
o
:

0
h
i
:

1
2
5
d
e
f
:

1
9
-
7
-
1
-
P
A
R
T

N
O

O
F
F
S
E
T
N
p
w
:
s
u
l
o
:

0
h
i
:

1
2
5
d
e
f
:

1
9
-
7
-
1
-
B
A
U
D

R
A
T
E
N
p
w
:
s
u
l
o
:

6
0
0
h
i
:

3
8
4
0
0
d
e
f
:

3
8
4
0
0
9
-
7
-
2
B
U
R
N
E
R

S
Y
S
T
E
M
9
-
7
-
2
-
M
A
S
T
E
R
-
S
L
A
V
E
N
p
w
:
c
u
d
e
f
:

m
a
s
t
e
r

9
-
7
-
2
-
O
I
L

O
K

D
I
F
F
N

%
p
w
:
c
u
l
o
:

0
.
5
h
i
:

1
0
0
d
e
f
:

5
9
-
7
-
2
-
A
I
R

O
K

D
I
F
F
N

%
p
w
:
c
u
l
o
:

0
.
5
h
i
:

1
0
0
d
e
f
:

5
9
-
7
-
2
-
M
A
N

S
T
E
P
N

%
p
w
:
c
u
l
o
:

0
.
5
h
i
:

2
d
e
f
:

1
9
-
7
-
2
-
A
I
R

O
I
L

D
I
F
N

%
p
w
:
c
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

1
0
9
-
7
-
2
-
M
A
X

O
I
L

O
U
T
N

%
p
w
:
s
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
9
-
7
-
2
-
(
o
n
l
y


i
f

S
M
A
L
L

G
U
N

M
A
X

O
I
L

S
.
G
U
N
N

%
p
w
:
s
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

4
0
9
-
7
-
2
-
R
E
D
U
C
E
D

P
R
S
N

B
A
R
p
w
:
s
u
l
o
:

0
h
i
:

2
7
d
e
f
:

4
9
-
7
-
2
-
L
O
A
D

L
I
M
I
T
N

%
p
w
:
s
u
l
o
:

0
h
i
:

1
0
0
d
e
f
:

6
0
9
-
7
-
2
-
T
A
U

W
.
L
E
V
E
L
N
p
w
:
n
o
l
o
:

0
h
i
:

2
0
d
e
f
:

0
9
-
7
-
2
-
T
A
U

A
I
R

F
L
O
W
N
p
w
:
n
o
l
o
:

0
h
i
:

2
0
d
e
f
:

0
9
-
7
-
3
-
O
I
L

S
A
M
P
L
I
N
G
N
p
w
:
s
u
l
o
:

0
h
i
:

1
0
d
e
f
:

1
9
-
7
-
3
B
U
R
N
E
R

O
P
T
I
O
N
S
9
-
7
-
3
-
0
P
R
E
S
S

U
N
I
T
N

B
A
R
p
w
:
c
u
d
e
f
:

b
a
r
9
-
7
-
3
-
1
O
X
Y
G
E
N
N
p
w
:
s
u
d
e
f
:

n
o
9
-
7
-
3
-
2
S
M
O
K
E

M
O
N
I
T
O
R
N
p
w
:
s
u
d
e
f
:

n
o
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

2
1

o
f

2
3
MENU TREE Menu tree 6_08#B.1
Language UK 26-23 / 59
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
7
-
3
-
3
S
T
E
A
M

D
U
M
P
N
p
w
:
s
u
d
e
f
:

n
o
9
-
7
-
3
-
4
F
W
.
P
U
M
P

C
T
R
L
N
p
w
:
s
u
d
e
f
:

n
o
9
-
7
-
3
-
5
F
W
.
R
E
G
.
O
U
T
.
L
I
M
N
p
w
:
s
u
l
o
:

-
1
0
0
0
h
i
:

1
5
0
0
d
e
f
:

0
9
-
7
-
3
-
6
W
A
T
E
R

L
.

C
O
N
T
N
p
w
.
s
u
m
o
d
o
n
/
o
f
f
m
o
d
9
-
7
-
3
-
7
W
A
T
E
R

L
.

C
O
N
T

E
G
B
N
p
w
.
s
u
m
o
d
o
n
/
o
f
f
m
o
d
9
-
7
-
3
-
8
F
W
.
O
U
T
P
U
T
.
C
F
G
N
p
w
:
s
u
d
e
f
:

o
f
f
9
-
7
-
3
-
9
F
W
.
R
E
G
.
T
Y
P
E
N
p
w
:
s
u
d
e
f
:

P
I
D
9
-
7
-
3
-
1
0
W
.
C
I
R
C
.
P
U
M
P
S
N
p
w
:
s
u
l
o
:

0
h
i
:

2
d
e
f
:

0
9
-
7
-
3
-
1
1
C
H
E
M
.

P
U
M
P
S
N
p
w
:
s
u
l
o
:

0
h
i
:

2
d
e
f
:

0
9
-
7
-
3
-
1
2
E
X
H
A
U
S
T

G
A
S
N
p
w
:
s
u
d
e
f
:

n
o
9
-
7
-
3
-
1
3
S
A
L
I
N
I
T
Y
N
p
w
:
s
u
d
e
f
:

o
f
f
9
-
7
-
3
-
1
4
T
E
M
P
.

U
P
T
A
K
E
N
p
w
:
s
u
d
e
f
:

o
f
f
9
-
7
-
3
-
1
5
I
N
E
R
T

G
A
S
N
p
w
:
s
u
d
e
f
:

o
f
f
9
-
7
-
3
-
1
6
K
E
Y

D
I
S
A
B
L
E
N
p
w
:
s
u
d
e
f
:

o
f
f
9
-
7
-
3
-
1
7
F
L
A
M
E

S
U
R
V
.

O
N
N
p
w
:
s
u
d
e
f
:

e
a
r
l
y
9
-
7
-
3
-
1
8
W
I
N
D
O
W
S
N
p
w
:
s
u
d
e
f
:

2
0
0
0
9
-
7
-
3
-
1
9
S
M
A
L
L

G
U
N
N
p
w
:
s
u
d
e
f
:
n
o
9
-
7
-
3
-
2
0
F
.
O
I
L

T
.
C
T
R
L
N
p
w
:
s
u
d
e
f
:
o
n
/
o
f
f
9
-
7
-
3
-
2
1
H
O
U
R
/
S
T
A
R
T

C
N
T
N
p
w
.
s
u
d
e
f
:
o
n
/
o
f
f
9
-
7
-
3
-
2
2
B
O
O
S
T
E
R

P
U
M
P
N
p
w
:
s
u
d
e
f
:
o
n
/
o
f
f
9
-
7
-
3
-
2
3
S
A
L
I
N
I
T
Y
/
O
I
L

S
H
T
N
p
w
.
s
u
d
e
f
:
o
n
/
o
f
f
9
-
7
-
3
-
2
4
T
E
M
P

C
O
M
M
O
N
N
p
w
.
s
u
d
e
f
:
y
e
s
9
-
7
-
3
-
2
5
P
R
S
S
.

C
O
M
M
O
N
N
p
w
.
s
u
d
e
f
:
y
e
s
9
-
7
-
3
-
2
6
O
I
L

P
U
M
P
S
N
p
w
:
s
u
l
o
:

1
h
i
:

2
d
e
f
:

2
9
-
7
-
3
-
2
7
S
O
O
T
B
L
O
W
E
R
N
p
w
:
s
u
d
e
f
:
y
e
s
9
-
7
-
3
-
2
8
A
U
X

P
U
M
P
N
p
w
:
s
u
d
e
f
:
n
o
9
-
7
-
3
-
2
9
F
L
A
M
E

S
C
A
N
N
E
R
S
N
p
w
:
s
u
l
o
:

1
h
i
:

2
d
e
f
:
2
9
-
7
-
3
-
3
0
W
I
N
D
B
O
X

T
E
M
P
N
p
w
:
s
u
d
e
f
:
n
o
9
-
7
-
3
-
3
1
M
O
D
B
U
S

E
X
T
.

P
R
I
O
N
p
w
:
s
u
l
o
:

O
F
F
h
i
:

H
I
G
H
d
e
f
:
O
F
F
9
-
7
-
3
-
3
2
B
L
O
C
K

A
L
A
R
M
G
R
P
N
p
w
:
s
u
d
e
f
:
y
e
s
9
-
7
-
4
A
N
A
L
O
G

O
P
T
I
O
N
S
9
-
7
-
4
-
0
B
O
I
L
E
R

P
R
E
S
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
1
O
I
L

P
R
E
S
S

N
Z
N
p
w
:
s
u
d
e
f
:

n
o
9
-
7
-
4
-
2
W
A
T
E
R

L
E
V
E
L
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
3
D
I
F
F
.

P
R
E
S
.
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
4
M
E

L
O
A
D
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
5
F

O
I
L

T
E
M
P
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
6
O
I
L

F
L
O
W
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
7
W
A
T
E
R

E
G
B
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
8
B
O
I
L
E
R

E
G
B
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
9
T
E
M
P
.
I
N
L
E
T
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
4
-
1
0
T
E
M
P
.
O
U
T
L
E
T
N
p
w
:
s
u
d
e
f
:

y
e
s
9
-
7
-
5
E
D
I
T

T
E
X
T
p
w
:
s
u
9
-
7
-
5
-
F
R
E
E

T
E
X
T







#

9
-
7
-
5
-
_
9
-
7
-
5
-
A
B
C
D
E
F
G
H
I
J
K
L
M
N

9
-
7
-
5
-
O
P
Q
R
S
T
U
V
W
X
Y
Z
.
/

9
-
7
-
6
L
I
N
K

T
E
X
T
9
-
7
-
6
-
#
0
1
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
2
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
3
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
4
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
5
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
6
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
7
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
8
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
0
9
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
9
-
7
-
6
-
#
1
0
F
R
E
E
T
E
X
T



N
O


p
w
:
s
u
d
e
f
:

N
O

0
0
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

2
2

o
f

2
3
MENU TREE Menu tree 6_08#B.1
26-24 / 59 Language UK
B
u
r
n
e
r
t
y
p
e
:

A
l
l
P
l
a
t
f
o
r
m
:

A
l
l
S
e
t
t
i
n
g
s
:

A
l
l
F
R
O
N
T

M
E
N
U
L
O
C
K

M
E
N
U
M
A
I
N

M
E
N
U
S
U
B

M
E
N
U

L
E
V
E
L

1
S
U
B

M
E
N
U

L
E
V
E
L

2
S
U
B

M
E
N
U

L
E
V
E
L

3
S
U
B

M
E
N
U

L
E
V
E
L

4
[
V
A
L
]
P
A
S
S
W
.
L
O
W
E
S
T
H
I
G
H
E
S
T
D
E
F
A
U
L
T
C
O
M
M
I
S
S
I
O
N
I
N
G
L
I
N
E

N
O
.
M
E
N
U

T
R
E
E

F
O
R

B
O
I
L
E
R

P
L
A
N
T

(
L
O
C
A
L

P
A
N
E
L
)
V
e
r
s
i
o
n

n
o
/
d
a
t
a
:

6
.
0
8
/
0
7
1
0
0
4
9
-
7
-
6
-
C
L
E
A
R











p
w
:
s
u
9
-
8
-
0
-
L
A
N
G
U
A
G
E
9
-
8
-
1
C
O
N
T
R
A
S
T
N
p
w
:
c
u
l
o
:

2
0
h
i
:

8
0
d
e
f
:

2
0
9
-
8
-
2
L
A
N
G
U
A
G
E
N
p
w
:
c
u
d
e
f
:

G
B
1
0
M
E
N
U

D
E
V
E
L
O
P
E
R
1
0
-
1
E
X
A
M
I
N
E

M
E
M
O
R
Y
1
0
-
1
-
1
[
A
D
R
]
[
C
O
N
T
E
N
T
]
N
n
p
1
0
-
2
E
D
I
T

M
E
M
O
R
Y
1
0
-
2
-
1
[
A
D
R
]
[
C
O
N
T
E
N
T
]
[
V
A
L
N
n
p
1
0
-
3
S
C
A
N

T
I
M
E
1
0
-
3
-
1
M
I
N
N
n
p
1
0
-
3
-
2
M
A
X
N
n
p
1
0
-
3
-
3
V
A
L
N
n
p
1
0
-
4
T
A
S
K

D
I
A
G
N
O
S
E
S
1
0
-
4
-
1
[
N
U
M
]
[
N
A
M
E
]
n
p
1
0
-
4
-
2
P
T
R
:
[
V
A
L
U
E
]

n
p
1
0
-
4
-
3
S
E
M
:
[
V
A
L
U
E
]

n
p
1
0
-
4
-
4
C
N
T
:
[
V
A
L
U
E
]

n
p
1
0
-
5
S
H
O
W

F
.
O
I
L

T
E
M
P
.
N
n
p
M
e
n
u
t
r
e
e

v
e
r

6
.
0
8
.
x
l
s
M

=

M
S
+
K
B
O
-
H
;


R

=

R
M
S
;


K
B
P

=

K
B
O
-
E
+
K
B
P
;

K
B
E

=

K
B
E

P
a
g
e

2
3

o
f

2
3
Explanation list for menu tree
1 Description
In the following tables the menu item lines for a control panel configured as a local
panel are listed and described. The lists are valid for boiler plants with modulating
pressure atomising burners set-up and operated as a single boiler.
The lists are divided into three columns. The first two columns contain the line numbers
and menu item lines which are directly copied from the actual menu tree. The last
column contains the description for each of the menu item lines. If an explanation for
a menu item line is requested the operator simply reads the line number in the actual
menu tree and locates the same number in these tables for a description.
Description of the menu item lines for a local panel (1 x MODUL.)
No. Menu item line Description
1 [SELECT 1] Displays a selected item. The items available for display can be selected from sub menu level
1 in the main menus: boiler, fuel oil, servo, and combust. A new item can be selected when
the black bar is placed at the desired item. The selection is made by pressing the set soft key
until the whole line has been emphasised.
2 [SELECT 2] Displays a selected item.
3 [SELECT 3] Displays a selected item. The last selected item will be shown in the third display line.
4 [STATE] Displays the burner state (starting, rising, modulation free, etc.), mode (locked/unlocked pan-
el).
5 KEY POSITION Indicates the position of the key operation lock. The default position is PP1 (power panel 1)
but this position can be changed in the request key menu item line.
6 REQUEST KEY Unlocks the actual local panel and operation can take place from this panel. Please note that
if any operation of the panel has not taken place for a period of time the key operation lock
automatically changes back to the default position (PP1). The time period for non-operation
can be set in the timer setup menu.
7 BOILER Menu for control of the steam pressure and water level.
8 BOILER PRES Menu for control of the boiler pressure. Please note that the transmitter is connected directly
on the boiler.
9 HI.SHT.DWN. Set point for high steam pressure shut down (burner cut off).
10 HIGH ALARM Set point for high steam pressure alarm.
11 LOW ALARM Set point for low steam pressure alarm.
12 ACTUAL SP. Displays the chosen set point which is selected in the setup/ctrl mode menu.
13 SETP. Set point for boiler operation in low pressure mode.
14 SETP.HIGH Set point for boiler operation in high pressure mode.
15 P Proportional gain for the regulation.
16 T.SAMPLE Time interval between reading output signals from the transmitter.
17 T.INT. Integral action time for the regulation.
18 T.DIFF. Derivative action time for the regulation.
19 REG OUTPUT Regulation output signal in %.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-25 / 59
Description of the menu item lines for a local panel (1 x MODUL.)
20 REMOTE CTRL Selection between automatic (0) or manual (1) control of the regulator. In manual control
mode (1) the regulator output can be increased or decreased by pressing the soft keys for
manual increase or decrease. Alteration of the regulator output can only be performed if it
takes place in the actual menu or in the previous menu step with the black bar placed on the
actual menu item. An alarm will be present when the regulator is in manual control mode.
Please note that the regulator must be active before the regulation output can be changed in
manual control mode.
21 WATER LEVEL Menu for control of the water level control.
Table 1
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-26 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
22 HI.SHT.DWN. Set point for high water level shut down (burner cut off). If this shut down function is not
required by the actual classification society, it should be set as high as possible.
23 HIGH ALARM Set point for high water level alarm.
24 LOW ALARM Set point for low water level alarm.
25 LO.SHT.DWN. Set point for too low water level shut down (burner cut off).
26 ACTUAL SP. Displays the active set point for normal water level.
27 SETP.OFFSET Displays the actual ramp function set point as a positive value when the set point changes
from "setp." to "setp.high" during burner start. The "setp.offset" function is not used for boiler
plants that include pressure atomising burners.
28 SETP. Set point for normal water level when the boiler is in starting, stopping or stopped mode. If
the firing is off, the water level falls. To prevent refilling of feed water, this set point is active
in these modes.
29 SETP.HIGH Set point for normal water level during normal operation.
30 DEADZONE Setting of dead zone for the water level regulation. The dead zone is used to ensure a steady
regulator output when the water level is close to the set point. When the actual value is 0.5
dead zone away from the set point the calculation of the PID P-part is stopped, leaving the I-
part to do the final tuning. In order to make this bump less the P-part distortion is calculated
as the distance from the set point 0.5 dead zone.
31 I-LOW LIMIT Limitation of the I-part for the PID water level regulation. When the low limitation is active
and the calculation exceeds -5% downwards, the I-part is limited and increased so that the
PID calculation maximum is -5%.
32 I-HIGH LIMIT Limitation of the I-part for the PID water level regulation. When the high limitation is active
and the calculation exceeds 105%, the I-part is limited and decreased so that the PID calcu-
lation maximum is 105%.
33 P Proportional gain for the regulation.
34 T.SAMPLE Time interval between reading output signals from the transmitter.
35 T.INT. Integral action time for the regulation.
36 T.DIFF. Derivative action time for the regulation.
37 P.PART Percentage value of the proportional part for the regulation. Used for commission purpose.
38 I.PART Percentage value of the integral part for the regulation. Used for commission purpose.
39 D.PART Percentage value of the derivative part for the regulation. Used for commission purpose.
40 REG OUTPUT Regulation output signal in %.
41 REMOTE CTRL Selection between automatic (0) or manual (1) control of the regulator. In manual control
mode (1) the regulator output can be increased or decreased by pressing the soft keys for
manual increase or decrease. Alteration of the regulator output can only be performed if it
takes place in the actual menu or in the previous menu step with the black bar placed on the
actual menu item. An alarm will be present when the regulator is in manual control mode.
Please note that the regulator must be active before the regulation output can be changed in
manual control mode.
42 FUEL OIL Menu for control of the fuel oil temperature and pressure.
43 F.OIL TEMP Menu for control of the fuel oil temperature. If on/off regulation is selected in the config/
burner option menu only the first five menu items will be displayed and active. When PWR
is selected all menu items are displayed and active.
44 HIGH ALARM Set point for high fuel oil temperature alarm.
45 LOW ALARM Set point for low oil temperature alarm.
46 LO.SHT.DWN. Set point for low fuel oil temperature shut down (burner cut off).
47 SETP. Set point for heavy fuel oil temperature.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-27 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
48 NEUTRALZONE Within the plus and minus value of the limit set in this menu the regulator will not perform
any regulation.
49 P Proportional gain for the regulation.
50 T.SAMPLE Time interval between reading output signals from the transmitter.
51 T.INT. Integral action time for the regulation.
52 T.DIFF. Derivative action time for the regulation.
53 P.PART Percentage value of the proportional part for the regulation. Used for commission purpose.
54 I.PART Percentage value of the integral part for the regulation. Used for commission purpose.
55 D.PART Percentage value of the derivative part for the regulation. Used for commission purpose.
56 MIN PULSE Setting of the minimum pulse time. The signal time from the regulator that must be exceeded
before regulation is initiated.
Table 2
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-28 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
57 RUN TIME Setting of the regulator run time. The time to carry out a full regulation.
58 REG OUTPUT Regulation output signal in %.
59 REMOTE CTRL Selection between automatic (0) or manual (1) control of the regulator. In manual control
mode (1) the regulator output can be increased or decreased by pressing the soft keys for
manual increase or decrease. Alteration of the regulator output can only be performed if it
takes place in the actual menu or in the previous menu step with the black bar placed on the
actual menu item. Furthermore, it is possible to set the regulation output manually from the
computer, if provided. An alarm will be present when the regulator is in manual control mode.
Please note that the regulator must be active before the regulation output can be changed in
manual control mode.
60 F.OIL PRES Menu for control of the fuel oil pressure.
61 LOW ALARM Set point for low oil pressure alarm and start of the stand-by oil pump.
62 LO.SHT.DWN. Set point for low oil pressure shut down (burner cut off).
63 SERVO Menu for control of the servo motor.
64 SERVO POS. Displays the actual position of the servo motor.
65 ACTUAL SP. Start of the burner and operation of the nozzle are controlled by the actual set point from the
boiler pres menu - the master start difference from the settings/m.start dif menu. Stop of the
burner and operation of the nozzle are controlled by the actual set point + the master stop
difference setting. Please note that master start/stop difference settings can be set to both
positive and negative values. During start or stop of the burner the set point is taken from the
pre-determined positions stated in the ignition position, purge position, minimum firing po-
sition.
66 NEUTRALZONE Within the plus and minus value of the limit set in this menu the regulator will not perform
any regulation.
67 REMOTE CTRL Selection between automatic (0) or manual (1) control of the regulator. In manual control
mode (1) the regulator output can be increased or decreased by pressing the soft keys for
manual increase or decrease. Alteration of the regulator output can only be performed if it
takes place in the actual menu or in the previous menu step with the black bar placed on the
actual menu item. An alarm will be present when the regulator is in manual control mode.
Please note that the regulator must be active before the regulation output can be changed in
manual control mode.
68 COMBUST Menu for display of combustion parameters.
69 SMK. DENSIT Displays the smoke density measurement. This menu will not be displayed if smoke density
monitor is not selected in the setup/burner option menu.
70 HIGH ALARM Set point for alarm of high soot contents in the flue gas.
71 OXYGEN Displays the oxygen sensor measurement. This menu will not be displayed if oxygen sensor
is not selected in the setup/burner option menu.
72 HIGH ALARM Set point for alarm of high oxygen contents in the flue gas.
73 TEMP. UPTAK Displays the uptake temperature measurement. This menu will not be displayed if uptake
temperature measurement is not selected in the setup/burner option menu.
74 HI.SHT.DWN. Set point for shut down because of high temperature in uptake (burner cut off).
75 HIGH ALARM Set point for alarm of high temperature in uptake.
76 CMN CTRL Menu for common control of pumps, smoke blower, steam dump equipment, salinity equip-
ment, inert gas mode, three point feed water regulation.
77 PUMP CTRL Menu for common control of pumps.
78 OIL PUMP Menu for control and display of the fuel oil pumps.
79 F.O.PMP1 SEL. Selection of operation mode for fuel oil pump 1 (stop, start, stand-by).
80 STATE Displays the state of fuel oil pump 1 (on/off).
81 F.O.PMP2 SEL. Selection of operation mode for fuel oil pump 2 (stop, start, stand-by).
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-29 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
82 STATE Displays the state of fuel oil pump 2 (on/off).
83 F.PMP1 REM START Status for remote start of fuel oil pump 1. If provided, the remote start is placed at the pump.
84 F.PMP1 REM STOP Status for remote stop of fuel oil pump 1. If provided, the remote stop is placed at the pump.
85 F.PMP2 REM START Status for remote start of fuel oil pump 2. If provided, the remote start is placed at the pump.
86 F.PMP2 REM STOP Status for remote stop of fuel oil pump 2. If provided, the remote stop is placed at the pump.
87 CHEM PMP Menu for control of the chemical pumps. This menu will not be displayed if chemical pumps
are not selected in the setup/burner option menu.
88 CHEM PMP1 Selection of operation mode for chemical pump 1 (start/stop).
89 CHEM PMP2 Selection of operation mode for chemical pump 2 (start/stop).
Table 3
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-30 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
90 WATER PUMP Menu for control of water pumps. This menu will not be displayed if water pumps are not
selected in the setup/burner option menu.
91 WATER PUMP Menu for control and display of the feed water pumps.
92 PUMP 1_1 SEL. Selection of operation mode for feed water pump 1 (stop, start, auto, stand-by).
93 MODE Selection of operation type for feed water pump 1 (main, service, not def.).
94 STATE Displays the state of feed water pump 1 (on/off).
95 PUMP 1_2 SEL. Selection of operation mode for feed water pump 2 (stop, start, auto, stand-by).
96 MODE Selection of operation type for feed water pump 2 (main, service, not def.).
97 STATE Displays the state of feed water pump 2 (on/off).
98 PUMP 2_1 SEL. Selection of operation mode for feed water pump 3 (stop, start, auto, stand-by).
99 MODE Selection of operation type for feed water pump 3 (main, service, not def.).
100 STATE Displays the state of feed water pump 3 (on/off).
101 PUMP 2_2 SEL. Selection of operation mode for feed water pump 4 (stop, start, auto, stand-by).
102 MODE Selection of operation type for feed water pump 4 (main, service, not def.).
103 STATE Displays the state of feed water pump 4 (on/off).
104 F.PMP1 REM START Status for remote start of feed water pump 1. If provided, the remote start is placed at the
pump.
105 F.PMP1 REM STOP Status for remote stop of feed water pump 1. If provided, the remote stop is placed at the pump.
106 F.PMP2 REM START Status for remote start of feed water pump 2. If provided, the remote start is placed at the
pump.
107 F.PMP2 REM STOP Status for remote stop of feed water pump 2. If provided, the remote stop is placed at the pump.
108 F.PMP3 REM START Status for remote start of feed water pump 3. If provided, the remote start is placed at the
pump.
109 F.PMP3 REM STOP Status for remote stop of feed water pump 3. If provided, the remote stop is placed at the pump.
110 F.PMP4 REM START Status for remote start of feed water pump 4. If provided, the remote start is placed at the
pump.
111 F.PMP4 REM STOP Status for remote stop of feed water pump 4. If provided, the remote stop is placed at the pump.
112 CIRCULATION PUMP Menu for control and display of the circulation pumps.
113 C.PMP1 SEL. Selection of operation mode for circulation pump 1 (stop, start, stand-by).
114 STATE Displays the state of circulation pump 1 (on/off).
115 C.PMP2 SEL. Selection of operation mode for circulation pump 2 (stop, start, stand-by).
116 STATE Displays the state of circulation pump 2 (on/off).
117 C.PMP1 REM START Status for remote start of circulation pump 1. If provided, the remote start is placed at the
pump.
118 C.PMP1 REM STOP Status for remote stop of circulation pump 1. If provided, the remote stop is placed at the
pump.
119 C.PMP2 REM START Status for remote start of circulation pump 2. If provided, the remote start is placed at the
pump.
120 C.PMP2 REM STOP Status for remote stop of circulation pump 2. If provided, the remote stop is placed at the
pump.
121 SMOKE BLOW Displays the state of the smoke blower for the smoke density equipment.
122 SMOKE BLOWER 1 Displays the state of the smoke density equipment.
123 STEAM DUMP Menu for control of the steam dump equipment. This menu will not be displayed if steam
dump equipment is not selected in the setup/burner option menu.
124 STEAM DUMP Menu for control and display of the steam dump equipment.
125 SETP. Set point for the steam dump pressure (opening of the steam dump valve).
126 P Proportional gain for the regulation.
127 T.SAMPLE Time interval between reading output signals from the transmitter.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-31 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
128 T.INT. Integral action time for the regulation.
129 T.DIFF. Derivative action time for the regulation.
130 REG OUTPUT Regulation output signal in %.
131 REMOTE CTRL Selection between automatic (0) or manual (1) control of the regulator. In manual control
mode (1) the regulator output can be increased or decreased by pressing the soft keys for
manual increase or decrease. Alteration of the regulator output can only be performed if it
takes place in the actual menu or in the previous menu step with the black bar placed on the
actual menu item. An alarm will be present when the regulator is in manual control mode.
Please note that the regulator must be active before the regulation output can be changed in
manual control mode.
132 SALINITY Menu for control of the salinity alarm equipment. This menu will not be displayed if salinity
alarm equipment is not selected in the setup/burner option menu.
133 SALINITY Menu for control and display of the salinity alarm equipment.
134 HI.SHT.DWN. Set point for shut down because of high salinity contents in feed water (burner cut off).
135 HIGH ALARM Set point for alarm of high salinity contents in feed water.
136 INERT GAS Menu for control of the inert gas mode.
Table 4
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-32 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
137 MIN LOAD The minimum load for operation in inert gas mode. If changed to a different value during
operation the burner load will be adjusted to the new set point. When inert gas mode is selected
(internal or external) the burner will be forced to start, if not already started. The burner load
will ramp up to minimum inert gas load. If the steam pressure drops below the set point the
burner load follows the stream pressure regulator. However, if the stream pressure regulator
sets the load below the minimum inert gas load the burner load is kept on minimum inert gas
load. In inert gas mode the normal set point for stop is inactive and the burner is only stopped
by an off signal for inert gas mode or the high steam pressure alarms.
138 FORCE Forces the boiler "ON" or "OFF" in inert gas mode from the local control panel. Note that the
external inert gas on/off function (switch) overrides the forced function.
139 [OIL OPERATION] Indicates the fuel choice (diesel oil operation or heavy oil operation). Please note that the fuel
type must be selected manually.
140 SURVEIL Menu for display of shut downs and alarms.
141 SHT.DWN. INSPEC-
TION
Menu for display of the first arising shut down out of the complete number of present shut
downs. All arising shut downs initiate burner cut off. By pressing the up and down arrow soft
keys on the right side of the panel all present shut downs can be viewed.
142 [SHT.DWN. NUM] Displays shut down number.
143 [SHT.DWN. TEXT] Displays shut down text.
144 ALARM INSPECTION Menu for display of the first arising alarm out of the complete number of present alarms. By
pressing the up and down arrow soft keys on the right side of the panel all present alarms can
be viewed.
145 [ALARM NUM] Displays alarm number.
146 [ALARM TEXT] Displays alarm text.
147 SETUP Menu for set-up of control mode, timers, settings, diagnoses, loggings, calibration, configu-
ration, and language.
148 CTRL MODE Menu for selection of burner mode and pressure mode.
149 BURNER CTRL MODE Selection of burner control mode (stopped, auto, manual). If auto mode is selected, the burner
mode can be switched directly between manual mode and automatic mode by pushing the soft
key for manual operation. Light in the LED above this soft key indicates that manual mode
is selected. Please note that during the start up sequence the burner control mode cannot be
changed and that a number of menus can only be operated if the burner is in stop mode.
150 SETPOINT SELECT Selection of pressure mode (low, high). If the boiler plant is not intended to operate at different
pressure modes, the set points in the boiler pressure menu should be set to the same level.
151 TIMERS Menu for readout and set-up of timers to sequences, surveillance, shared operation, power
panels, and communication.
152 TIMERS Menu for timer readout. The readouts are only shown when the individual steps and items are
active.
153 SEQUENCE Menu for sequence timer readout.
154 START START Timer countdown for the minimum running time of the combustion air fan (steam atomising
burners).
155 IGNITER POS Timer countdown for positioning the ignition burner (steam atomising burners).
156 FD.FAN ST. Timer countdown for the combustion air fan starting period (steam atomising burners).
157 PURGE Timer countdown for the purge period.
158 FLUSH START Timer countdown for the flush start period for pressure atomising burners (MS, RMS).
159 FLUSH BREAK Timer countdown for the flush break period for pressure atomising burners (MS, RMS).
160 FLUSH END Timer countdown for the flush end period for pressure atomising burners (MS, RMS).
161 IGNITION Timer countdown for the ignition period.
162 SAFETY TIME Timer countdown for the safety time period.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-33 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
163 START SEQ Timer countdown for the maximum permissible starting time of the burner.
164 FLAME STAB. Timer countdown for the flame stabilising period.
165 LOW FIRING Timer countdown for the low firing period.
166 RISING TIME Timer countdown for the rising period.
167 STEAM PG.PO Timer countdown for regulator positioning to steam purge position (steam atomising burners).
168 STEAM PURG1 Timer countdown for the steam purge 1 period (steam atomising burners). Oil valves close
and steam purge valve opens.
169 STEAM PURG2 Timer countdown for the steam purge 2 period (steam atomising burners). Atomising steam
valve closes, and steam purge valve remains open.
170 POSTPURGE Timer countdown for the post purge period.
Table 5
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-34 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
171 SURVEILLANCE Menu for readout of surveillance timers.
172 WATER HI.SD Timer countdown for delay of the high water level shut down (burner cut off).
173 WATER HI.AL Timer countdown for delay of the high water level alarm.
174 WATER LO.AL Timer countdown for delay of the low water level alarm.
175 WATER LO.SD Timer countdown for delay of the low water level shut down (burner cut off).
176 WATER SW LO Timer countdown for delay of the low water level shut down switch (burner cut off).
177 PMS FEEDBAC Timer countdown for maximum feedback signal time from the ships power management sys-
tem (PMS), steam atomising burners.
178 SERVO POS Timer countdown for feedback signal from servo position (pressure atomising burners).
179 B.MOT.STAR Timer countdown for feedback signal from burner motor started (pressure atomising burners).
180 W. REG OUT Timer countdown for signal to start/stop of feed water pumps in boiler plants with on/off feed
water regulation.
181 SMOKE HI.AL Timer countdown for delay of high alarm from the smoke density equipment.
182 TEMP HI.AL. Timer countdown for delay of high alarm from the uptake temperature measurement.
183 TEMP HI.SD. Timer countdown for delay of high shut down (burner cut off) from the uptake temperature
measurement.
184 KEY HOLD Timer countdown for delay of non-operation of an unlocked local panel.
185 BOOST.M.ST. Timer countdown for feedback signal from booster pump motor started (large pressure atom-
ising burners).
186 SHARED Menu for readout of shared timers.
187 SAL HI.AL. Timer countdown for delay of high alarm from the salinity alarm equipment.
188 SAL HI.SD. Timer countdown for delay of high shut down (burner cut off) from the salinity alarm equip-
ment.
189 OIL LO.AL. Timer countdown for delay of low oil pressure alarm and start of the stand-by oil pump.
190 POWER PANEL 1 Menu for readout of power panel 1 timers.
191 F.O.PMP 1 Timer countdown for feedback signal from fuel oil pump 1.
192 F.O.PMP 2 Timer countdown for feedback signal from fuel oil pump 2.
193 FUEL PRESS Timer countdown for feedback signal from start stand-by fuel oil pump. The start is effected
by the low fuel oil pressure alarm.
194 F.O.PMP Timer countdown for feedback signal from shut down and cut off functions during start of the
fuel oil pumps.
195 DO TO HFO Timer countdown for feedback signal from positioning the three way valve from diesel oil
operation to heavy fuel oil operation.
196 HFO TO DO Timer countdown for feedback signal from positioning the three way valve from heavy fuel
oil operation to diesel oil operation.
197 KEY TIMEOUT Timer countdown for communication feedback signal between the panels.
198 POWER PANEL 2 Menu for readout of power panel 1 timers.
199 F.W.PMP 1 Timer countdown for feedback signal from feed water pump 1.
200 F.W.PMP 2 Timer countdown for feedback signal from feed water pump 2.
201 F.W.PMP 3 Timer countdown for feedback signal from feed water pump 3.
202 F.W.PMP 4 Timer countdown for feedback signal from feed water pump 4.
203 F.W. DELAY Timer countdown for delay of start stand-by feed water pump in case of low pressure. The
timer is active when the pumps are configured as 2+1 pumps in the burner option menu.
204 F.W. M. RUN Timer countdown for change of feed water pump (main/service pump) after stop of the burner.
205 F.W. DELAY2 Timer countdown for delay of start stand-by feed water pump in case of low pressure. The
timer is active when the pumps are configured as 2+2 pumps in the burner option menu.
Normally used for three point feed water regulation.
206 C.PUMP 1 Timer countdown for feedback signal from circulation pump 1.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-35 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
207 C.PUMP 2 Timer countdown for feedback signal from circulation pump 2.
208 COMMUNICATION Menu for readout of communication timers. The timers continuously count down until they
are reset by the feedback signals. After resetting the timers commence a new countdown.
209 PANEL1 OFFL Timer countdown for communication feedback signal from local panel 1.
210 PANEL2 OFFL Timer countdown for communication feedback signal from local panel 2.
211 TIMERS SETUP Menu for timer set-up.
212 SEQUENCE Menu for set-up of sequence timers.
213 START START Setting of the minimum running time for the combustion air fan (steam atomising burners).
Table 6
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-36 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
214 IGNITER POS Setting of the maximum time for positioning the ignition burner (steam atomising burners).
215 FD.FAN ST. Setting of the maximum start time for the combustion air fan (steam atomising burners).
216 PURGE Setting of the purge time period.
217 FLUSH START Setting of the flush start time period for pressure atomising burners (MS, RMS). If the cold/
warm start thermostat is activated during start up the safety solenoid valves positioned before
and after the pre-heater and nozzle head open. Hereby the oil system on the burner is flushed
with heavy fuel oil and the temperature is increased by the pre-heater.
218 FLUSH BREAK Setting of the flush break time period for pressure atomising burners (MS, RMS). After the
flush start time period has expired the solenoid valves close and the heavy fuel oil which is
contained inside the pre-heater is heated to the correct temperature.
219 FLUSH END Setting of the flush end time period for pressure atomising burners (MS, RMS). When the
flush break time period is completed the solenoid valves open for a time period before the
burner is started. In this way the heavy fuel oil contained inside the pre-heater will reach nozzle
head when the oil is ignited.
220 IGNITION Setting of the ignition time period.
221 SAFETY TIME Setting of the safety time period.
222 START SEQ Setting of the maximum start time for the burner.
223 FLAME STAB. Setting of the flame stabilising time period.
224 LOW FIRING Setting of the low firing time.
225 RISING TIME Setting of the rising time.
226 STEAM PG.PO Setting of the time for regulator positioning to steam purge position (steam atomising burners).
227 STEAM PURG1 Setting of the steam purge 1 time period (steam atomising burners). Oil valves close and steam
purge valve opens.
228 STEAM PURG2 Setting of the steam purge 2 time period (steam atomising burners). Atomising steam valve
closes, and steam purge valve remains open.
229 POSTPURGE Setting of the postpurge time period.
230 SURVEILLANCE Menu for set-up of surveillance timers.
231 WATER HI.SD Setting of the timer delay for high water level shut down (burner cut off).
232 WATER HI.AL Setting of the timer delay for high water level alarm.
233 WATER LO.AL Setting of the timer delay for low water level alarm.
234 WATER LO.SD Setting of the timer delay for low water level shut down (burner cut off).
235 WATER SW LO Setting of the timer delay for low water level shut down switch (burner cut off).
236 PMS FEEDBAC Setting of the timer delay from the power management system (PMS) of the ship, steam
atomising burners.
237 SERVO POS Setting of the timer delay for servo position (pressure atomising burners).
238 B.MOT.STAR Setting of the timer delay for burner motor started (pressure atomising burners).
239 W. REG OUT Setting of the time delay for start/stop of feed water pumps in boiler plants with on/off feed
water regulation.
240 SMOKE HI.AL Setting of the timer delay for high alarm from the smoke density equipment.
241 TEMP HI.AL. Setting of the timer delay for high temperature alarm in uptake.
242 TEMP HI.SD. Setting of the timer delay for high temperature shut down in uptake (burner cut off).
243 KEY HOLD Setting of the timer delay for non-operation of an unlocked local panel.
244 BOOST.M.ST. Setting of the timer delay for booster pump motor started (large pressure atomising burners).
245 SHARED Menu for set-up of shared timers.
246 SAL HI.AL. Setting of the timer delay for high alarm from the salinity alarm equipment.
247 SAL HI.SD. Setting of the timer delay for high shut down (burner cut off) from the salinity alarm equip-
ment.
248 OIL LO.AL. Setting of the timer delay for low pressure alarm and start of the stand-by oil pump.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-37 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
249 POWER PANEL 1 Menu for set-up of power panel 1 timers.
250 F.O.PMP 1 Time period for delay of feedback signal from fuel oil pump 1.
251 F.O.PMP 2 Time period for delay of feedback signal from fuel oil pump 2.
252 FUEL PRESS Time period for delay of start stand-by fuel oil pump. The start is effected by the low fuel oil
pressure alarm.
253 F.O.PMP Time period for delay of shut down and cut off functions during start of the fuel oil pumps.
254 DO TO HFO Time period for positioning the three way valve from diesel oil operation to heavy fuel oil
operation.
255 HFO TO DO Time period for positioning the three way valve from heavy fuel oil operation to diesel oil
operation.
Table 7
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-38 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
256 KEY TIMEOUT Time period in which absent communication between the panels is accepted before setting
the key operation lock to power panel 1.
257 POWER PANEL 2 Menu for set-up of power panel 2 timers.
258 F.W.PMP 1 Time period for delay of feedback signal from feed water pump 1.
259 F.W.PMP 2 Time period for delay of feedback signal from feed water pump 2.
260 F.W.PMP 3 Time period for delay of feedback signal from feed water pump 3.
261 F.W.PMP 4 Time period for delay of feedback signal from feed water pump 4.
262 F.W. DELAY Time period for delay of start stand-by feed water pump in case of low pressure. The timer is
active when the pumps are configured as 2+1 pumps in the burner option menu.
263 F.W. M. RUN Time period for change of feed water pump (main/service pump) after stop of the burner.
264 F.W. DELAY2 Time period for delay of start stand-by feed water pump in case of low pressure. The timer is
active when the pumps are configured as 2+2 pumps in the burner option menu. Normally
used for three point feed water regulation.
265 C.PUMP 1 Time period for delay of feedback signal from circulation pump 1.
266 C.PUMP 2 Time period for delay of feedback signal from circulation pump 2.
267 COMMUNICATION Menu for set-up of communication timers.
268 PANEL1 OFFL Time period in which absent communication from local panel 1 is accepted.
269 PANEL2 OFFL Time period in which absent communication from local panel 2 is accepted.
270 DATE/TIME The date/time is used to indicate time for the event and alarm system. It might be advantageous
to adjust the date/time for GMT in order to have a fixed time during sailing. The date/time is
stored in the control system and remembered even if the system is switched off for a period
of time.
271 HOUR Must be adjusted as a 24 hour watch.
272 MIN Adjustment of minutes.
273 SEC Adjustment of seconds.
274 DAY Adjustment of date.
275 MONTH Adjustment of month.
276 YEAR Adjustment of year (4 digits).
277 HOUR/START CNT Main menu for hour counters.
278 LOAD >25% Hour counter menu for burner load below 25% (from minimum/ignition load to 100%).
279 LOAD >25% Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
burner or burner parts replacement the total/service running hours can be manually reset in
the sub menus by setting of new values via entering of the super user password.
280 TOT.HOUR Counts and displays the total running hours for the burner at operation below 25%.
281 SRV.HOUR Counts and displays accumulated running hours below 25% since the last reset of service
hours.
282 SRV.VAL Setting of the service interval in hours.
283 RESET Reset of the service counters
284 LOAD >50% Hour counter menu for burner load below 50% (from 25% to 100%).
285 LOAD >50% Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
burner or burner parts replacement the total/service running hours can be manually reset in
the sub menus by setting of new values via entering of the super user password.
286 TOT.HOUR Counts and displays the total running hours for the burner at operation below 50%.
287 SRV.HOUR Counts and displays accumulated running hours below 50% load since the last reset of service
hours.
288 SRV.VAL Setting of the service interval in hours.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-39 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
289 RESET Reset of the service counters
290 LOAD >75% Hour counter menu for burner load below 75% (from 50% to 100%).
291 LOAD >75% Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
burner or burner parts replacement the total/service running hours can be manually reset in
the sub menus by setting of new values via entering of the super user password.
292 TOT.HOUR Counts and displays the total running hours for the burner at operation below 75%.
293 SRV.HOUR Counts and displays accumulated running hours below 75% load since the last reset of service
hours.
294 SRV.VAL Setting of the service interval in hours.
Table 8
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-40 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
295 RESET Reset of the service counters
296 LOAD Hour counter menu for burner load above 75% (from 75% to 100%).
297 LOAD Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
burner or burner parts replacement the total/service running hours and number of starts can
be manually reset in the sub menus by setting of new values via entering of the super user
password.
298 TOT.HOUR Counts and displays the total running hours for the burner at operation above 75%.
299 SRV.HOUR Counts and displays accumulated running hours above 75% load since the last reset of service
hours.
300 SRV.VAL Setting of the service interval in hours.
301 RESET Reset of the service counters
302 TOT.START Counts and displays the total number of starts for the burner.
303 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
304 SMOKE BLOW Hour counter menu for smoke density blower.
305 SMOKE BLOW Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
blower replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
306 TOT.HOUR Counts and displays the total running hours for the connected blower/motor.
307 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
308 SRV.VAL Setting of the service interval in hours.
309 RESET Reset of the service counters
310 TOT.START Counts and displays the total number of starts for the connected blower/motor.
311 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
312 BOOST PUMP Hour counter menu for booster pump. Note only used for large pressure atomising burners.
313 BOOST PUMP Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
314 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
315 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
316 SRV.VAL Setting of the service interval in hours.
317 RESET Reset of the service counters
318 TOT.START Counts and displays the total number of starts for the connected pump/motor.
319 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
320 BURN.MOTOR Hour counter menu for burner motor.
321 BURN.MOTOR Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
motor replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
322 TOT.HOUR Counts and displays the total running hours for the connected motor.
323 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
324 SRV.VAL Setting of the service interval in hours.
325 RESET Reset of the service counters
326 TOT.START Counts and displays the total number of starts for the connected motor.
327 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
328 FUEL PUMP 1 Hour counter menu for fuel oil pump 1.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-41 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
329 FUEL PUMP 1 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
330 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
331 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
332 SRV.VAL Setting of the service interval in hours.
333 RESET Reset of the service counters
334 TOT.START Counts and displays the total number of starts for the connected pump/motor.
335 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
Table 9
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-42 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
336 FUEL PUMP 2 Hour counter menu for fuel oil pump 2.
337 FUEL PUMP 2 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
338 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
339 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
340 SRV.VAL Setting of the service interval in hours.
341 RESET Reset of the service counters
342 TOT.START Counts and displays the total number of starts for the connected pump/motor.
343 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
344 CIRC.PUMP 1 Hour counter menu for circulation pump 1.
345 CIRC.PUMP 1 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
346 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
347 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
348 SRV.VAL Setting of the service interval in hours.
349 RESET Reset of the service counters
350 TOT.START Counts and displays the total number of starts for the connected pump/motor.
351 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
352 CIRC.PUMP 2 Hour counter menu for circulation pump 2.
353 CIRC.PUMP 2 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
354 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
355 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
356 SRV.VAL Setting of the service interval in hours.
357 RESET Reset of the service counters
358 TOT.START Counts and displays the total number of starts for the connected pump/motor.
359 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
360 CHEM.PUMP 1 Hour counter menu for chemical pump 1.
361 CHEM.PUMP 1 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
362 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
363 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
364 SRV.VAL Setting of the service interval in hours.
365 RESET Reset of the service counters
366 TOT.START Counts and displays the total number of starts for the connected pump/motor.
367 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
368 CHEM.PUMP 2 Hour counter menu for chemical pump 2.
369 CHEM.PUMP 2 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-43 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
370 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
371 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
372 SRV.VAL Setting of the service interval in hours.
373 RESET Reset of the service counters
374 TOT.START Counts and displays the total number of starts for the connected pump/motor.
375 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
376 F.W.PUMP 1 Hour counter menu for feed water pump 1.
Table 10
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-44 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
377 F.W.PUMP 1 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
378 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
379 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
380 SRV.VAL Setting of the service interval in hours.
381 RESET Reset of the service counters
382 TOT.START Counts and displays the total number of starts for the connected pump/motor.
383 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
384 F.W.PUMP 2 Hour counter menu for feed water pump 2.
385 F.W.PUMP 2 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
386 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
387 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
388 SRV.VAL Setting of the service interval in hours.
389 RESET Reset of the service counters
390 TOT.START Counts and displays the total number of starts for the connected pump/motor.
391 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
392 F.W.PUMP 3 Hour counter menu for feed water pump 3.
393 F.W.PUMP 3 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
394 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
395 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
396 SRV.VAL Setting of the service interval in hours.
397 RESET Reset of the service counters
398 TOT.START Counts and displays the total number of starts for the connected pump/motor.
399 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
400 F.W.PUMP 4 Hour counter menu for feed water pump 4.
401 F.W.PUMP 4 Hour counter sub menu. When the service hours exceed the set interval an alarm is given.
Note that the service time continues to count irrespectively of the alarm condition. In case of
pump replacement the total/service running hours and number of starts can be manually reset
in the sub menus by setting of new values via entering of the super user password.
402 TOT.HOUR Counts and displays the total running hours for the connected pump/motor.
403 SRV.HOUR Counts and displays accumulated running hours since the last reset of service hours.
404 SRV.VAL Setting of the service interval in hours.
405 RESET Reset of the service counters
406 TOT.START Counts and displays the total number of starts for the connected pump/motor.
407 SRV.START Counts and displays accumulated number of starts since the last reset of service hours.
408 SETTINGS Menu for setting start/stop limits and servo motor positions in different states.
409 START/STOP LIMITS Menu for start and stop set points for the boiler.
410 M.START DIF Setting of the start difference for the boiler. The set point for start of the boiler consists of the
actual set point from the boiler pres menu and the pressure difference, which is set in this
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-45 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
menu. This means that when the steam pressure is equal to the actual set point + start difference
set point, the boiler starts.
411 M.STOP DIFF Setting of the stop difference for the boiler. The set point for stop of the boiler consists of
actual set point from the boiler pres menu and the pressure difference, which is set in this
menu. This means that when the steam pressure is equal to the actual set point + stop difference
set point, the boiler stops.
412 MIN.FIRING POSITION Menu for setting the servo motor position when the burner is in minimum firing position.
413 SERVO POS. Setting of the servo motor position.
414 PURGE POSITION Menu for setting the servo motor position when the burner is in purge position.
Table 11
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-46 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
415 SERVO POS. Setting of the servo motor position.
416 IGNITION POSITION Menu for setting the servo motor position when the burner is in ignition position.
417 SERVO POS. Setting of the servo motor position.
418 DIAGNOSES Menu for viewing software information, digital input/output status, setting digital output for
testing, and password changes.
419 SOFTWARE VERSION Menu for general system information.
420 [PANEL TYPE] Displays panel type.
421 [VERSION] Displays date and time for installation and software version number.
422 [INFO 1] Displays information text.
423 [INFO 2] Displays information text.
424 DIGITAL INPUT Menu for viewing the status of the digital inputs (0/1).
425 EXTERN SHUTDOWN 1 Status for extern shutdown 1.
426 HI STM PRESS SWITCH Status for the high steam pressure switch.
427 LANCE REDRAWN Status for burner lance redrawn (steam atomising burners) or burner swing out (pressure
atomising burners).
428 WATER LEVEL LOW Status for too low water level shut down.
429 FLAME SCANNER 1 Status for flame scanner 1.
430 FLAME SCANNER 2 Status for flame scanner 2.
431 START PERM.PMS Status for the power management system of the ship (PMS) (steam atomising burners).
432 IGN.INS./O.TEMP.L Status for ignition burner inserted (steam atomising burners) or oil temperature low (pressure
atomising/rotary cup burners).
433 AIR CLOSED/
O.TEMP.H
Status for air inlet vanes closed (steam atomising burners) or oil temperature high (pressure
atomising burners).
434 OIL V.POS/Q.C.VALVE Status for oil valves closed (steam atomising burners) or quick closing valves (pressure atom-
ising/rotary cup burners).
435 H.OIL PRS/IGN.F.SUV Status for ignition flame surveillance (steam atomising burners) or high oil pressure in return
line (pressure atomising burners).
436 F.IN WB./O.TEMP CTR Status for fire in wind box (steam atomising/rotary cup burners) or oil temperature control on/
off (pressure atomising burners).
437 HIGH TEMP UPTAKE Status for high temperature in uptake switch.
438 LOW COMB AIR PRESS Status for low combustion air pressure switch.
439 LOW OIL PRESS
NOZZL
Status for low oil pressure at the nozzle.
440 L.OIL TEMP N/LOW AT Status for low oil temperature at the nozzle (pressure atomising burners) or low atomising air
pressure (rotary cup burners).
441 COLD/WARM START Status for cold/warm start.
442 INERT GAS Status for inert gas mode.
443 EXTERN STOP 1 Status for extern stop 1.
444 EXTERN STOP 2 Status for extern stop 2.
445 EXTERN SHUTDOWN 2 Status for extern shutdown 2.
446 HEAVY FUEL OPERAT Status for position of heavy fuel oil/diesel oil operation.
447 F.O.PMP1 FB Status of feedback signal for fuel oil pump 1 running.
448 F.O.PMP2 FB Status of feedback signal for fuel oil pump 2 running.
449 BURNER MOTOR 1 FB Status of feedback signal for burner motor 1 running.
450 BURNER MOTOR 1 OL Status for burner motor 1 overload.
451 SALINITY Status for the salinity shut down.
452 OIL CONTENT Status for high oil content in the feed water.
453 HIGH GAS TEMP.AT EG Status for high gas temperature at the exhaust gas boiler.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-47 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
454 F.O.PMP1 REM STOP Status for remote stop of fuel oil pump 1. If provided, the remote stop is placed at the pump.
455 F.O.PMP1 REM START Status for remote start of fuel oil pump 1. If provided, the remote start is placed at the pump.
456 F.O.PMP2 REM STOP Status for remote stop of fuel oil pump 2. If provided, the remote stop is placed at the pump.
457 F.O.PMP2 REM START Status for remote start of fuel oil pump 2. If provided, the remote start is placed at the pump.
458 F.W.PMP1 FB Status of feedback signal for feed water pump 1 running.
459 F.W.PMP1 STBY Status of feedback signal for selecting feed water pump 1 to stand-by mode.
460 F.W.PMP2 FB Status of feedback signal for feed water pump 2 running.
461 F.W.PMP2 STBY Status of feedback signal for selecting feed water pump 2 to stand-by mode.
Table 12
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-48 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
462 F.W.PMP3 FB Status of feedback signal for feed water pump 3 running.
463 F.W.PMP3 STBY Status of feedback signal for selecting feed water pump 3 to stand-by mode.
464 F.W.PMP4 FB Status of feedback signal for feed water pump 4 running.
465 F.W. PMP4 STBY Status of feedback signal for selecting feed water pump 4 to stand-by mode.
466 CIRC.PMP1 FB Status of feedback signal for circulation pump 1 running.
467 CIRC.PMP STBY Status of feedback signal for start of stand-by circulation pump.
468 CIRC.PMP LF Status of feedback signal for low circulation flow.
469 CIRC.PMP2 FB Status of feedback signal for circulation pump 2 running.
470 C.PMP1 REM STOP Status for remote stop of circulation pump 1. If provided, the remote stop is placed at the
pump.
471 C.PMP1 REM START Status for remote start of circulation pump 1. If provided, the remote start is placed at the
pump.
472 C.PMP2 REM STOP Status for remote stop of circulation pump 2. If provided, the remote stop is placed at the
pump.
473 C.PMP2 REM START Status for remote start of circulation pump 2. If provided, the remote start is placed at the
pump.
474 F.W.PMP1 REM STOP Status for remote stop of feed water pump 1. If provided, the remote stop is placed at the pump.
475 F.W.PMP1 REM START Status for remote start of feed water pump 1. If provided, the remote start is placed at the
pump.
476 F.W.PMP2 REM STOP Status for remote stop of feed water pump 2. If provided, the remote stop is placed at the pump.
477 F.W.PMP2 REM START Status for remote start of feed water pump 2. If provided, the remote start is placed at the
pump.
478 F.W.PMP3 REM STOP Status for remote stop of feed water pump 3. If provided, the remote stop is placed at the pump.
479 F.W.PMP3 REM START Status for remote start of feed water pump 3. If provided, the remote start is placed at the
pump.
480 F.W.PMP4 REM STOP Status for remote stop of feed water pump 4. If provided, the remote stop is placed at the pump.
481 F.W.PMP4 REM START Status for remote start of feed water pump 4. If provided, the remote start is placed at the
pump.
482 DIGITAL OUTPUT Menu for viewing the status of the digital outputs (0/1).
483 ATM.S.P/SERVO UP Status for output signal to atomising steam pressure up (steam atomising burners) or servo
motor load up (pressure atomising/rotary cup burners).
484 ATM.S.P/SERVO DW Status for output signal to atomising steam pressure down (steam atomising burners) or servo
motor load down (pressure atomising/rotary cup burners).
485 IGNITION Status for output signal to ignition system.
486 NOZZLE2/W.MAN AU-
TO
Status for output signal for nozzle 2 (two-stage pressure atomising burners) or auto/manual
operation of external water level regulation.
487 OIL V/ NOZZLE 1 Status for output signal to oil valves (steam atomising burners) or solenoid valve for nozzle
1 (two-stage pressure atomising burners).
488 ATM STEAM/SAFETY
V
Status for output signal to atomising steam valve (steam atomising burners) or safety valves
1 and 2 in nozzle head (pressure atomising burners).
489 S.PURGE/HEATING E Status for output signal to steam purge (steam atomising burners) or heating elements (pressure
atomising/rotary cup burners).
490 BOILER PRESS HI.SET Status for boiler operation in high pressure mode.
491 SOOTBLOWER Status for the IGS interlock control valve (if provided)
492 SHT.DWN. Status for common shut down.
493 START REQ TO PMS Status for output signal for start request to the power management system (PMS) of the ship,
steam atomising burners.
494 ALARM Status for alarm presence.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-49 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
495 ALARM H.WATER L Status for high water level alarm.
496 ALARM L.WATER L Status for low water level alarm.
497 BURNER IN STOP Status for output signal to burner in stop mode.
498 F. W. REG. ON/OFF Status for output signal to feed water regulation.
499 F.O.PMP 1 Status for output signal to fuel oil pump 1.
500 F.O.PMP 2 Status for output signal to fuel oil pump 2.
501 SMOKE BLOWER 1 Status for output signal to the smoke density blower 1 (actual boiler).
502 SMOKE BLOWER 2 Status for output signal to the smoke density blower 2 (connected boiler).
503 F.O.PMP.STB.STRT Status for output signal to fuel oil pump stand-by start.
504 BURNER MOTOR 1 Status for output signal to burner motor (pressure atomising/rotary cup burners).
505 F.D FAN1/F.SAFETY Status for output signal to combustion air fan 1 (pressure atomising/rotary cup burners) or
pre-heater safety thermostat (pressure atomising burners).
506 F.D FAN2/F.HEAT Status for output signal to combustion air fan 2 (pressure atomising/rotary cup burners) or
pre-heater release function (pressure atomising burners).
507 CHEMICAL ST 1 Status for output signal to chemical station 1.
Table 13
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-50 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
508 CHEMICAL ST 2 Status for output signal to chemical station 2.
509 OIL TRACING Status for output signal to the oil tracing system.
510 F.W.PMP1 Status for output signal to feed water pump 1.
511 F.W.PMP2 Status for output signal to feed water pump 2.
512 F.W.PMP3 Status for output signal to feed water pump 3.
513 F.W.PMP4 Status for output signal to feed water pump 4.
514 CIRC.PMP1 Status for output signal to circulation pump 1.
515 CICR.PMP2 Status for output signal to circulation pump 2.
516 F.W.PMP.STB.STRT Status for output signal to feed water pump stand-by start.
517 CIRC.PMP.STB.STRT Status for output signal to circulation pump stand-by start.
518 SUPERUSER KEY-
WORD
Menu for display of latest use of super user password.
519 [USED] Display the date and time for the latest entering of the super user password.
520 SERIAL NUMBER Menu for software information.
521 SERIAL NO Displays the EPROM serial number. The number must not be 0.
522 COMMISSIONED Displays the commissioning date for the EPROM.
523 ERASE EEPROM Erases the EEPROM. If the EEPROM is erased the original factory settings from the EPROM
will be active (default settings).
524 NO OF SHT.DWN. Menu for displays of the total number of shut downs since commissioning.
525 NO OF SHT.DWN. Displays of the total number of shut downs since commissioning.
526 DIGITAL OUTPUT
TEST
Menu for digital output test. By applying 1/0 signals to the digital output, the pumps, regula-
tors, etc. can be tested, which might be useful during commissioning. The burner(s) must be
in stop mode before this menu can be entered.
527 ATM.S.P/SERVO UP Setting of the output signal to atomising steam pressure up (steam atomising burners) or servo
motor load up (pressure atomising/rotary cup burners).
528 ATM.S.P/SERVO DW Setting of the output signal to atomising steam pressure down (steam atomising burners) or
servo motor load down (pressure atomising/rotary cup burners).
529 IGNITION Setting of the output signal to ignition system.
530 NOZZLE2/W.MAN AU-
TO
Setting of the output signal to nozzle 2 (two-stage pressure atomising burners) or auto/manual
operation of external water level regulation.
531 OIL V/ NOZZLE 1 Setting of the output signal to oil valves (steam atomising burners) or solenoid valve for nozzle
1 (two stage pressure atomising burners).
532 ATM STEAM/SAFETY
V
Setting of the output signal to atomising steam valve (steam atomising burners) or safety valves
1 and 2 in nozzle head (pressure atomising burners).
533 S.PURGE/HEATING E Setting of the output signal to steam purge (steam atomising burners) or heating elements
(pressure atomising/rotary cup burners).
534 BOILER PRESS HI.SET Setting of the output signal for boiler operation in high pressure mode.
535 SOOTBLOWER Setting of the output signal for the IGS interlock control valve (if provided)
536 SHT.DWN. Setting of the output signal for shut down.
537 START REQ TO PMS Setting of the output signal for start request to the power management system (PMS) of the
ship, steam atomising burners.
538 ALARM Setting of the output signal for alarms.
539 ALARM H.WATER L Setting of the output signal for high water level alarm.
540 ALARM L.WATER L Setting of the output signal for low water level alarm.
541 BURNER IN STOP Setting of the output signal to burner in stop mode.
542 F. W. REG. ON/OFF Setting of the output signal to feed water regulation.
543 F.O.PMP 1 Setting of the output signal to fuel oil pump 1.
544 F.O.PMP 2 Setting of the output signal to fuel oil pump 2.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-51 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
545 SMOKE BLOWER 1 Setting of the output signal to the smoke density blower 1 (actual boiler).
546 SMOKE BLOWER 2 Setting of the output signal to the smoke density blower 2 (connected boiler).
547 F.O.PMP.STB.STRT Setting of the output signal to fuel oil pump stand-by start.
548 BURNER MOTOR 1 Setting of the output signal to burner motor (pressure atomising/rotary cup burners).
549 F.D FAN1/F.SAFETY Setting of the output signal to combustion air fan 1 (pressure atomising/rotary cup burners)
or pre-heater safety thermostat (pressure atomising burners).
550 F.D FAN2/F.HEAT Setting of the output signal to combustion air fan 2 (pressure atomising/rotary cup burners)
or pre-heater release function (pressure atomising burners).
Table 14
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-52 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
551 CHEMICAL ST 1 Setting of the output signal to chemical station pump 1.
552 CHEMICAL ST 2 Setting of the output signal to chemical station pump 2.
553 OIL TRACING Setting of the output signal to the oil tracing system.
554 F.W.PMP1 Setting of the output signal to feed water pump 1.
555 F.W.PMP2 Setting of the output signal to feed water pump 2.
556 F.W.PMP3 Setting of the output signal to feed water pump 3.
557 F.W.PMP4 Setting of the output signal to feed water pump 4.
558 CIRC.PMP1 Setting of the output signal to circulation pump 1.
559 CIRC.PMP2 Setting of the output signal to circulation pump 2.
560 F.W.PMP.STB.STRT Setting of the output signal to feed water pump stand-by start.
561 CIRC.PMP.STB.STRT Setting of the output signal to circulation pump stand-by start.
562 NEW PASSWORD Menu for change and reset of password.
563 NEW PASSWORD The user and/or super user passwords can be changed. The change will only be effective for
the entered password.
564 RESET PASSWORDS Reset of both the user and super user passwords to factory setting. A special password is
necessary to enter the menu. This password, as well as the super user password, will only be
known by Aalborg Industries. The factory setting of the user password is 1234.
565 LOGGINGS Menu for shut down log and oil flow counter.
566 INSPECT SHT.DWN.
LOG
Menu for display of the last 20 shut downs.
567 [SHT.DWN. NUM] Date and time for the shut down.
568 [SHT.DWN. TEXT] Displays shut down text.
569 CALIBRATE Menu for calibrating operating ranges for transmitters, servo motor, etc.
570 WATER LEVEL Menu for setting the water level transmitter operating range.
571 WATER LEVEL Actual value of the water level in mm.
572 RANGE HIGH The high water level point (in mm) set during commission should be used as the high range
level.
573 RANGE LOW The low water level (in mm) set during commission should be used as the low range level.
574 RND.1/10MM Calculation resolution for the water level controller.
575 BOILER PRES Menu for setting the boiler pressure transmitter operating range.
576 BOILER PRES Actual value of the boiler pressure in bar.
577 RANGE HIGH Appears from the set point diagram for the local panel.
578 RANGE LOW Appears from the set point diagram for the local panel.
579 FUEL O.PRES Menu for setting the fuel oil pressure transmitter operating range.
580 FUEL O.PRES Actual value of the fuel oil pressure in bar.
581 RANGE HIGH Appears from the set point diagram for the power panel.
582 RANGE LOW Appears from the set point diagram for the power panel.
583 OXYGEN SENS Menu for setting the oxygen sensor operating range.
584 OXYGEN SENS Actual value of the oxygen content in %.
585 RANGE HIGH Should be calibrated according to configuration of the oxygen sensor.
586 RANGE LOW Should be calibrated according to configuration of the oxygen sensor.
587 SMOKE DENS. Menu for setting the smoke density operating range.
588 SMOKE DENS. Actual value of the smoke density in %.
589 RANGE HIGH Should be calibrated according to configuration of the smoke density equipment.
590 RANGE LOW Should be calibrated according to configuration of the smoke density equipment.
591 SALINITY Menu for setting the salinity equipment operating range.
592 SALINITY Actual value of the salinity equipment.
593 RANGE HIGH Appears from the set point diagram for the power panel.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-53 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
594 RANGE LOW Appears from the set point diagram for the power panel.
595 ST.PRES.COM Menu for setting the common pressure transmitter operating range. Please note that if the
common steam pressure transmitter and the boiler pressure transmitter are mounted at different
height levels and far apart, the pressure loss resulting from the height difference and friction
should be taken into consideration. Adjustments of the low and high ranges should always be
carried out to fit the actual pressure at the boiler.
596 ST.PRES.COM Actual value of the common steam pressure in bar.
597 RANGE HIGH Appears from the set point diagram for the power panel.
598 RANGE LOW Appears from the set point diagram for the power panel.
Table 15
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-54 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
599 SERVO MOTOR Menu for setting the servo motor operating range.
600 SERVO MOTOR Actual value of the servo motor position in percent.
601 RAW DATA Actual value of the servo motor position indicated as a resistance signal.
602 RANGE HIGH Setting of the resistance signal value when the air dampers are fully open (90). The value is
displayed in the raw data menu item line when the air dampers are in this position (90).
603 RANGE LOW Setting of the resistance signal value when the air dampers are fully closed (0). The value is
displayed in the raw data menu item line when the air dampers are in this position (0).
604 T.MIN->MAX Setting of the time to operate the servo motor from 0 - 90. Appears from the name plate on
the servo motor (normally 30 seconds).
605 CONFIG Menu for set-up of hardware configuration, burner type, additional operating parameters, and
selection of system options.
606 PANEL SYSTEM Menu for set-up of panel type, burner type, and communication. Operation in this menu is
only possible if the burner(s) is in stop mode.
607 PANEL TYPE Selection between panel type: LOCAL 1, LOCAL 2, POWER 1, POWER 2 (if provided),
EGB, or not def. During the initial commissioning in double boiler plants, it should be decided
which boiler is number 1 and which boiler is number 2. The number of the local panels should
then be selected according to the boiler number.
608 BURNER TYPE Selection between burner type: KB, MODUL., 2-STAGE, KBSA, KBSD, or not def.
609 BURNER FAMILY Selection between MULTI or ALONE operation. If the boiler is part of a double boiler plant
and master/slave operation is possible (and intended) MULTI must be selected. If not ALONE
must be selected.
610 NODE NO.OFFSET Setting of the communication signal between panels. All included panels in a single boiler
plant or a multi boiler plant with common supply systems must be set to the same node number
in order to communicate together. In a multi boiler plant with separate supply systems the
node number must be divided into groups. This means that all included panels for the first
boiler should have the same identical number and all included panels for the second boiler
should have another identical number. The difference in the number value must always be
minimum 12. E.g. if the node number for the first group of panels is 1, then the second group
of panels must be set to 1 + 12 = 13.
611 PART NO.OFFSET The node No.offset of the partner boiler panels in a multi boiler plant must be entered in the
menu item line. In case of a single boiler plant it is advisable also to enter the node number
in this menu item line.
612 BAUD RATE Speed of the signal transmission. The baud rate should be set as high as possible.
613 BURNER SYSTEM Menu for setting additional regulation parameters.
614 MAN STEP Defines the step size for the ramp function in manual operation. The value is added to or
subtracted from the regulation output each time the soft keys for manual operation are pressed
in the increase or decrease directions respectively. If the soft keys are continuously pressed,
the load alteration increases rapidly because the step size will be continuously added or sub-
tracted.
615 REDUCED PRS Setting of the reduced pressure. If the boiler pressure is below the pressure set in this menu,
the boiler load is limited by the setting in the menu config/burner system/load limit.
616 LOAD LIMIT Setting of the maximum load limit. If the boiler pressure is below the pressure set in the menu
config/burner system/reduced prs, the maximum load (oil flow) can be limited by the setting
in this menu. This action contributes to a reduction of the pressure overswing during pressure
rising.
617 TAU W.LEVEL Makes an average value of the number of measurements which are set. The pick-up rate is in
1/100 sec. This prevents sudden uncontrolled regulations caused by a faulty measurement.
618 OIL SAMPLING This menu item has no function and must be set to the default value.
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-55 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
619 BURNER OPTIONS Menu for additional choice of equipment and pressure units.
620 PRESS UNIT Selection of pressure units (bar, Mpa, or kg/cm
2
).
621 OXYGEN Additional choice of oxygen sensor equipment.
622 SMOKE MONITOR Additional choice of smoke density equipment.
623 STEAM DUMP Additional choice of steam dump equipment.
624 FW.PUMP CTRL Additional choice of feed water pumps.
625 FW.REG.OUT.LIM Limits for start/stop of feed water pumps in boiler plants with on/off feed water regulation.
The entered value is divided into two equal levels that represent the start and stop set points
below and above normal water level respectively.
Table 16
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-56 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
626 FW.OUTPUT CFG Selection of I/P positioner for the feed water regulation. Some boiler plants may be provided
with two feed water control valves of different sizes. If OFF is selected the output signal will
only be active on I/P positioner 1 and If EXH is selected the output signal will only be active
on I/P positioner 2. If OIL is selected the output signal will change between I/P positioner 1
and I/P positioner 2 depending on the burner state. When the burner is in operation I/P posi-
tioner 1 is active and when the burner is stopped I/P positioner 2 is active. Please note that if
high pressure mode is selected, the output signal is maintained at the largest control valve.
627 FW.REG.TYPE Selection of feed water regulation type between PID (ordinary regulation), 3PT (three point
regulation), EXT (external regulation), or 2PT (two point regulation). In boiler plants that
include pressure atomising burners only PID regulation should be selected.
628 W.CIRC.PUMPS Additional choice of water circulation pumps by selecting number of pumps.
629 CHEM. PUMPS Additional choice of chemical pumps by selecting number of pumps.
630 EXHAUST GAS Additional choice of an exhaust gas boiler. This will only effect the graphic pictures for the
PC monitoring and control system. If a PC is not provided this menu item has no function.
631 SALINITY Additional choice of salinity alarm equipment. Selection between OFF, MON, and If MON
is selected the control system only monitors the salinity equipment. If SUR is selected the
alarm and shut down for the salinity equipment are also active.
632 TEMP. UPTAKE Additional choice of uptake temperature measurement. Selection between OFF, MON, and If
MON is selected the control system only monitors the uptake measurement. If SUR is selected
the alarm and shut down for the uptake measurement are also active.
633 INERT GAS Additional choice of inert gas mode.
634 KEY DISABLE Disable the key operation lock. Operation can take place from all operation places. However,
the time period for non-operation of the panels is still active. This timer can be set in the timer
setup menu.
635 FLAME SURV. ON Activates flame surveillance. If "early" is selected the flame surveillance is activated before
continuing to step 5 (safety time) in the burner start-up sequence. If "late" is selected the flame
surveillance is activated in step 5 (safety time).
636 WINDOWS Selection of windows platform in connection with the PC monitoring and control system. If
a PC is provided check the platform and set the same platform (win 2000/3.11) for the con-
troller software in this menu point.
637 SMALL GUN Additional choice of two burner lance operation. Selection between "no" or "yes". Note that
this menu item line has no function for boiler plants that include pressure atomising burners.
638 F.OIL T.CTRL Selection of on/off or PWR (pulse wide reg.) temperature regulation for pressure atomising
burners. On/off should be selected for WH burners and PWR for KBO burners.
639 HOUR/START CNT. Activation of hour counters.
640 BOOSTER PUMP Additional choice of booster pump. Note only used for large pressure atomising burners
641 ANALOG OPTIONS Menu for setting analogue inputs.
642 BOILER PRES Activates or deactivates the analogue input for the boiler pressure transmitter. It should only
be deactivated if the panel type is selected as EGB and the exhaust gas boiler is without separate
steam space.
643 OIL PRESS NZ Activates or deactivates the analogue input for the nozzle oil pressure transmitter. Some steam
atomising burners may be provided with a pressure transmitter while others with a pressure
gauge.
644 WATER LEVEL Activates or deactivates the analogue input for the water level controller. It should only be
deactivated if the panel type is selected as EGB and the exhaust gas boiler is without separate
steam space.
645 DIFF.PRESS. Activates or deactivates the analogue input for the differential pressure transmitter used for
exhaust gas measurement if the panel type is selected as EGB. Some exhaust gas boilers may
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-57 / 59
Description of the menu item lines for a local panel (1 x MODUL.), continued
be provided with a differential pressure transmitter while others with a U-tube differential
pressure gauge.
646 ME LOAD Activates or deactivates the analogue input for main engine load if the panel type is selected
as EGB.
647 EDIT TEXT Menu for assigning new texts to existing alarms and shut downs. In the following menu item
lines it is possible to enter new texts which can overwrite already existing alarm and shut down
texts.
648 FREE TEXT Indication of which editable text is currently edited (free text #xx). It is possible to enter 10
editable text lines each with a maximum of 20 characters.
649 [TYPED TEXT] New text for the specific free text No. is indicated in this menu item line.
Table 17
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
26-58 / 59 Language UK
Description of the menu item lines for a local panel (1 x MODUL.), continued
No. Menu item line Description
650 [TEXT] Line for keyboard from which characters are entered. Navigation on the keyboard is done with
the left and right arrow keys. When the set key is pressed a character is entered and shown in
the typed text menu item line. Shifting between free text lines is done with the "" and ""
characters. When the editing of text is completed the "end" character must be activated to exit
these menu item lines.
651 LINK TEXT Menu for linking and clearing new alarm/shut down texts. The new texts entered in the "edit
text" menu can be assigned to existing alarm and shut down numbers. By means of the set
key each of the ten possible free text lines can be entered. At first selection is made between
alarm link "AL.", shut down link "SD.", or no link "NO". Then the desired alarm or shut
number is entered. Default numbers appear from the alarm and shut down lists. When a new
free text has been linked and the specific alarm or shut down state arises it will be displayed
in the surveillance menu. The new text as well as free text number and link number are indi-
cated. Note that any entered texts and links will only be displayed on the local panels, and not
on a connected PC. Entered texts and links can be erased by means of the clear function. Here
selection is made between clearing all texts "text", all link info "link", or both "all". If "all" is
selected the system is set back to the default values for alarm and shut down texts.
652 [#01 FREE TEXT] Setting of link info (alarm link, shut down link, or no link) and number (alarm No. or shut
down No.) for entered free text number 01.
653 [#02 FREE TEXT] Setting of link info (alarm link, shut down link, or no link) and number (alarm No. or shut
down No.) for entered free text number 02.
654 [#03 FREE TEXT] Setting of link info (alarm link, shut down link, or no link) and number (alarm No. or shut
down No.) for entered free text number 03.
655 [#04 FREE TEXT] Setting of link info (alarm link, shut down link, or no link) and number (alarm No. or shut
down No.) for entered free text number 04.
656 CLEAR Clearing of texts, link info, or both.
657 LANGUAGE Menu for language and LCD display contrast selection.
658 CONTRAST Setting of the light contrast in the LCD display.
659 LANGUAGE It is only possible to choose GB (English).
Table 18
EXPLANATION LIST FOR MENU TREE OM9306_34#A.2
Language UK 26-59 / 59