Implementation of Ring Topology in Cisco Last Updated : 23 Jul, 2025 Comments Improve Suggest changes Like Article Like Report Ring topology is a kind of arrangement of the network in which every device is linked with two other devices. This makes a circular ring of interconnected devices which gives it its name. Data is usually transmitted in one direction along the ring, known as a unidirectional ring. The data is delivered from one device to the next until it reaches the decided destination. In a bidirectional ring, data can travel in either direction. To learn about Ring Topology refer to the Advantages and Disadvantages of ring topology article. Steps to Configure and Setup Ring Topology in Cisco Packet Tracer :Step 1: First, open the cisco packet tracer desktop and select the devices given below: S.NODeviceModel Name1.PCPC2.SwitchPT-SwitchIP Addressing Table S.NODeviceIPv4 AddressSubnet Mask1.pc0192.168.0.1255.255.255.02.pc1192.168.0.2255.255.255.03.pc2192.168.0.3255.255.255.04.pc3192.168.0.4255.255.255.0Then, create a network topology as shown below the image.Use an Automatic connecting cable to connect the devices with others.Step 2: Configure the PCs (hosts) with IPv4 address and Subnet Mask according to the IP addressing table given above. To assign an IP address in PC0, click on PC0.Then, go to desktop and then IP configuration and there you will IPv4 configuration.Fill IPv4 address and subnet mask. Assigning IP address using the ipconfig command, or we can also assign an IP address with the help of a command.Go to the command terminal of the PC.Then, type ipconfig <IPv4 address><subnet mask><default gateway>(if needed)Example: ipconfig 192.168.0.1 255.255.255.0Repeat the same procedure with other PCs to configure them thoroughly.Step 3: Verify the connection by pinging the IP address of any host in PC0. Use the ping command to verify the connection.As we can see we are getting replies from a targeted node on both PCs.Hence the connection is verified.A simulation of the experiment is given below we have sent two PDU packets one targeted from PC0 to PC2 and another targeted from PC1 to PC3. Comment More infoAdvertise with us Next Article Implementation of Mesh Topology in Cisco S shadit13064 Follow Improve Article Tags : Computer Networks Cisco CCNA Networking Fundamentals Practice Tags : Cisco Similar Reads Implementation of Bus Topology in Cisco A bus topology is a network in which nodes are directly linked with a common half-duplex link. A host on a bus topology is called a station. In a bus network, every station will accept all network packets, and these packets generated by each station have equal information priority. A bus network inc 2 min read Implementation of Mesh Topology in Cisco Pre-requisite: Advantages and Disadvantages of Mesh Topology In the mesh topology of networking, each and every device sends its own signal to the other devices that are present in the arrangement of the network. Steps to Configure and Setup Ring Topology in Cisco Packet Tracer:Step 1: First, open 2 min read Implementation of Tree Topology in Cisco Pre-Requisite: Advantages and Disadvantages of Tree Topology In the tree topology of networking, the elements and devices are arranged like a tree structure and have branches of connections between the devices connected to each other. To implement tree topology in Cisco there are various steps as fo 2 min read Implementation of Hybrid Topology in Cisco The arrangement of a network that comprises nodes and connecting lines via sender and receiver is referred to as network topology. The combination of two or more topologies in a computer network is called Hybrid Topology. These combined topologies can be a combination of bus topology, mesh topology, 2 min read Subnetting Implementation in Cisco Packet Tracer A subnet, or subnetwork, is a part of a larger network. Subnets are a logical part of an IP network into multiple, smaller network components. The Internet Protocol (IP) is the method for transmitting data from one computer to another over the internet network. Each computer, or host, on the interne 3 min read EIGRP Implementation in Cisco The functions of a dynamic routing protocol are the same as a static routing protocol. If the destination is unreachable from a point of routing then the other path can be created to reach the destination. To learn about EIGRP refer to EIGRP fundamentals. Steps to Configure and Verify EIGRP in Cisco 2 min read Like