Flag register in 8085 microprocessor

Control Signals in 8155 Microprocessor

Last Updated : 03 Mar, 2020

In handshake mode, when both the ports A and B are configured, port A uses the lower three signals of port C(i.e, PC0, PC1, PC2) and port B uses the upper three signals (i.e, PC3, PC4, PC5). The diagram can be followed as:

Figure - 8155 with Handshake mode
The functions of the above signals can be seen as follows:

STB (Strobe Input): This is an input handshake signal. This is connected from a peripheral to the 8155. The low on this signal informs the 8155 that data are strobed into the input port.
BF (Buffer Full): This is an active high signal, which basically indicates the presence of a data byte in the port.
INTR (Interrupt Request): As clear from the name itself, the rising edge of the STB signal generates this signal. This happens whenever the interrupt flip-flop (INTE) is enabled. This can be used to interrupt the MPU.
INTE (Interrupt Enable): This is an internal flip-flop which is used to enable or disable the interrupt capability of the 8155. The interrupts of port A and port B are controlled by bits D4 and D5, respectively, in the control register.

These control signals can be used to implement either interrupt I/O or status check I/O.

Flag register in 8085 microprocessor

skylags

Improve

Article Tags :

Similar Reads

ALE Pin in 8085 Microprocessor

This pin of the 8085 microprocessor, ALE, is one of the most important pins used in interfacing with external memory devices. During any machine cycle, while interfacing with an external memory using the 8085 microprocessor, the ALE pin latches the lower-order address bits, A0-A7.During the beginnin

Serial I/O Lines in 8085 Microprocessor

Introduction : The 8085 microprocessor is a widely used 8-bit microprocessor that was developed by Intel. One of the important features of the 8085 microprocessor is its ability to support serial input/output (I/O) operations. The 8085 microprocessor has two dedicated pins, namely, the Serial Data I

Flag register in 8085 microprocessor

In the 8085 microprocessor, the Flag Register is a kind of 8-bit register comprising five flags that indicate the results from arithmetic and logical operations. These flags include the Sign flag, indicating whether the result is negative; the Zero flag, set in case the result is zero; the Auxiliary

Process control instructions in 8086 microprocessor

Process control instructions are the instructions which control the processor's action by setting(1) or resetting(0) the values of flag registers. Following is the table showing the list of process control instructions: OPCODEOPERANDEXPLANATIONEXAMPLESTCnonesets carry flag to 1STCCLCnoneresets carry

Introduction of Microprocessor

In this article we will go through the Microprocessor, we will first define what is a Microprocessor, then we will go through its different types with its block diagram and we will see different types of processors, At last, we will conclude our article with some applications and FAQs.What is Microp

Microprocessor | 8251 USART

Prerequisite - 8259 PIC Microprocessor 8251 universal synchronous asynchronous receiver transmitter (USART) acts as a mediator between microprocessor and peripheral to transmit serial data into parallel form and vice versa. It takes data serially from peripheral (outside devices) and converts into p

Interrupts in 8085 Microprocessor

In the 8085 microprocessor, interrupt is a process in which control of the program transfers from the main program to the starting location defined by interrupt. It is a process by which some external device or peripheral informs microprocessor to become ready for data communication by accepting the

Instruction Word Size in Microprocessor

The 8085 instruction set is classified into 3 categories by considering the length of the instructions. In 8085, the length is measured in terms of "byte" rather than "word" because 8085 microprocessor has 8-bit data bus. Three types of instruction are: 1-byte instruction, 2-byte instruction, and 3-

Microprocessor | 8254 programmable interval timer

8254 is a device designed to solve the timing control problems in a microprocessor. It has 3 independent counters, each capable of handling clock inputs up to 10 MHz, and size of each counter is 16 bit. It operates in +5V regulated power supply and has 24 pin signals. All modes are software programm

Pin diagram of 8085 microprocessor

The 8085 microprocessor is a popular 8-bit microprocessor developed by Intel. It has 40 pins, each with a specific function for interfacing with memory, input/output devices, and other components.Pin diagram of 8085 microprocessor is shown below: Key Pin Descriptions1. Address Bus and Data BusAddres