Installation C264/EN IN/E20
MiCOM C264 Page 65/78
Click the Format flash memory button and wait till the end.
NOTE: The passwords and logoff time-outs are spared by this operation.
[Link] Launch a telnet session
To perform tasks that CAT cannot handle, launch the default Windows Telnet client on the
operator PC and wait for the login request:
The "logout" command or the windows close can be used to terminate the session.
As Telnet is launched independently of CAT, multi sessions on two or more computers are
possible.
As Telnet used TCP/IP stack, the computer has to be accessible from the PC in this mode.
7.5.10 REU board CAT configuration
The Configuration tool CAT allows to monitor and update the firmware of the REU Boards.
NOTE: Use CAT version A3.15 or later.
From CAT main panel, select Manage boot and network parameters view
On the panel, click on REU Switch parameters button
FIGURE 4: ACCESS REU SETTINGS
C264/EN IN/E20 Installation
Page 66/78 MiCOM C264
The window REU settings is displayed as below (use the vertical scrollbar to access all
settings).
FIGURE 5: WINDOW REU SETTINGS
Refresh: reload parameter from the board.
Apply: apply parameters set to the board.
Factory Mode: set the setting to default value
The setting table below describes the Editable REU Parameters:
Label Description Field
Name Name of Certificate mandatory
Description Description of certificate
FLASH Status of flashing IDLE
process. ERROR
Status can be set only OK
when state is not BUSY
BUSY. This is used to
reset status before new
update
ETH_MAC_S Source MAC address xx-xx-xx-xx-xx-
used to send xx
supervision frame in
HSR or PRP mode.
ETH_MAC_I Source MAC address xx-xx-xx-xx-xx-
used by HSR/PRP xx
module to answer to
HOST_CPU on interlink
port only.
MODE Allows to set mode of HUB
HSR/PRP module SWITCH
HSR
PRP
RSTP
PORT_A
PORT_B
OFF
Installation C264/EN IN/E20
MiCOM C264 Page 67/78
PTP Enable/disable PTP ON
IEEE1588 protocol. OFF
PTP_PRIMARY_DOMAIN Define the primary 0..255
domain use to
syntonizer internal
hsr/prp ptp clock.
PTP_ANNOUNCE_RECEIPT_TIMEOUT Timeout period of 2..10
announce message.
PTP_LOG_MIN_PDELAY_REQ_INTERVAL Period of Pdelay_Req n = 0..5
message sent to
compute link delay.
Value is 2^n seconds.
HSR_PRP_LIFE_CHECK_INTERVAL Period of hsr/prp 100..5000
supervision frame
sending.
HSR_PRP_ENTRY_FORGET_TIME Period of clearing the 10..1340
duplicate table.
HSR_PRP_SUPERVISION_FRAME Enable or disable of ON
hsr/prp supervision OFF
frame.
PRP_TRANSPARENT_RECEPTION Enable or disable ON
removing of RCT PRP OFF
frame in PRP mode.
AUTO_INTERLINK Enable to automatically ON
switch the interlink port. OFF
FLOW_CONTROL_INTERLINK Enable interlink to ON
sends PAUSE frame OFF
according to 802.3
when there is overflow
in HSR mode.
LLDP_AB Enable lldp on LanA ON
and LanB. OFF
LLDP_I Enable lldp on Interlink ON
port. OFF
LLDP_A_REMOTE The LLDP remote state NONE
LLDP_B_REMOTE of port. ChassisID
LLDP_I_REMOTE PortID
TTL
MAC_SRC
IP
IP_ADDR IP address used by [Link]
internal CPU of
HSR/PRP board for
LLDP protocol.
RSTP_BRIDGE_PRIORITY Value prepended to 0..61440
Ethernet mac address
to form the Bridge
Identifier.
RSTP_PORT_A_PRIORITY Value prepended to port 0..240
RSTP_PORT_B_PRIORITY number from the Port step of 16
Identifier.
RSTP_PORT_A_PATH_COST Value added to current 1..200000000
RSTP_PORT_B_PATH_COST path cost on root port.
RSTP_FORCE_PROTOCOL_VERSION Parameter to force use RSTP
version of RSTP STP.
protocol backward to
STP or to RSTP(v2).
RSTP is also STP
compatible
RSTP_BRIDGE_MAX_AGE Determine the 6..40
maximum distance
between any bridge and
the current root bridge.
C264/EN IN/E20 Installation
Page 68/78 MiCOM C264
RSTP_BRIDGE_ FORWARD_DELAY Delay used for 4..30
compatibility with older
STP standard.
RSTP_BRIDGE_HELLO_TIME Period of BPDU frame. 1..2
UNICAST_FORWARD_ALL Enable the forward to A ON
or B port of unicast OFF
frame targeted to
interlink port.
ACCEPT_ALL Define the sent to ON
Interlink port. OFF
MULTICAST_ALL All multicast frames ON
from port A & B are sent OFF
to Interlink port.
MULTICAST_yy Multicast address xx-xx-xx-xx-xx-
accepted toward xx
Interlink.
Installation C264/EN IN/E20
MiCOM C264 Page 69/78
For information, the setting table below describes the Read Only REU Parameters:
Label Description Field
VERSION Version of running software x.y
x = Major revision
y = Minor revision
FPGA Version of setting FACTORY
USER
EEPROM Status of internal EEPROM OK
KO
EXT_PWR Status of external power supply ON
OFF
PSU_USE Current power supply source EXT_POWER
IED_PWR
TRA/TRB Status of optical transceiver A/B NOT_FITTED
RX_OFF
TX_OFF
OK
RSTP_BRIDGE_ROOT MAC address of the RSTP root xx-xx-xx-xx-xx-xx
bridge.
RSTP_BRIDGE_PORT_A Current state of port State:Role
RSTP_BRIDGE_PORT_B State:
- FORWARDING
- DISCARDING
- DISABLED
Role:
- ROOT
- DESIGNATED
- ALTERNATE
- BACKUP
- DISABLED
C264/EN IN/E20 Installation
Page 70/78 MiCOM C264
[Link] REU firmware upgrade with CAT
To upgrade a firmware of REU2 board, do following:
From Configuration tool CAT main panel, select Browse files view
On Local PC Side tree, select the firmware file to send to board
Click on Send button to send the firmware file forward REU board
The C264 automatically detects the reception of firmware file and upgrade it to REU board;
After upgrade, the REU board restarts with the new firmware.
Installation C264/EN IN/E20
MiCOM C264 Page 71/78
[Link] REU first configuration with wflash_nios2
At first use, or in case of anomaly, the REU is configurable with wflash_nios2 tool.
Wflash_nios2 is software allowing to set the parameter of REU board. The PC which run wflash_nios
is connected directly to the interlink port of REU board.
To read parameters of REU board with wflash_nios2
status
Click on Read button to get the current parameters of REU board
C264/EN IN/E20 Installation
Page 72/78 MiCOM C264
To set parameters of REU board with wflash_nios2
set
Click on Write button to set the new parameters of REU board
The parameters are set as following format:
MODE:HSR:
PTP:OFF:
PTP_PRIMARY_DOMAIN:0:
PTP_ANNOUNCE_RECEIPT_TIMEOUT:3:
PTP_LOG_MIN_PDELAY_REQ_INTERVAL:0:
HSR_PRP_LIFE_CHECK_INTERVAL:2000:
HSR_PRP_ENTRY_FORGET_TIM[Link]
HSR_PRP_SUPERVISION_FRAME:ON:
PRP_TRANSPARENT_RECEPTION:ON:
AUTO_INTERLINK:OFF:ok, safe state.
FLOW_CONTROL_INTERLINK:ON:
LLDP_AB:OFF:
LLDP_I:OFF:
LLDP_A_REMOTE:NONE:
LLDP_B_REMOTE:NONE:
LLDP_I_REMOTE:NONE:
IP_ADDR:[Link]:
RSTP_BRIDGE_PRIORITY:32768:
RSTP_PORT_A_PRIORITY:128:
RSTP_PORT_B_PRIORITY:128:
RSTP_PORT_A_PATH_COST:200000:
RSTP_PORT_B_PATH_COST:200000:
RSTP_FORCE_PROTOCOL_VERSION:RSTP:
RSTP_BRIDGE_MAX_AG[Link]
RSTP_BRIDGE_FORWARD_DELAY:15:
RSTP_BRIDGE_HELLO_TIM[Link]
RSTP_PORT_A:DISABLED:
RSTP_PORT_B:DISABLED:
UNICAST_FORWARD_ALL:OFF:
ACCEPT_ALL:ON:
MULTICAST_ALL:ON:
MULTICAST_00:00-00-00-00-00-00:
MULTICAST_01:00-00-00-00-00-00:
MULTICAST_02:00-00-00-00-00-00:
MULTICAST_03:00-00-00-00-00-00:
MULTICAST_04:00-00-00-00-00-00:
MULTICAST_05:00-00-00-00-00-00:
MULTICAST_06:00-00-00-00-00-00:
MULTICAST_07:00-00-00-00-00-00:
Installation C264/EN IN/E20
MiCOM C264 Page 73/78
To upgrade firmware of REU board with wflash_nios2
Click on check box Update Firmware and select the firmware file to install on REU board.
Click on Write button to send new firmware file to REU board.
After upgrade, the REU board restarts with the new firmware.
7.5.11 Security administrator functions
At installation, no account might be locked and no password is in force (keep the field blank).
The security tasks include:
Management: all the parameters are profile-specific, but valid for all of the three clients
(LHMI, CAT, MiCOM S1): a strong password is desirable (refer to PACiS/EN CS
chapter), 8 characters are indispensable
To unlock an account (observer/system engineer/ system administrator):
Select the user account in the drop-down list (second section)
Click the button Unlock Account.
