User Manual

For User

Do not charge the radio or battery in an explosive environment, such as gas, dust,smoke
area [Link] turn off the radio when nearby gas station. Do not disassemble or modify
the [Link] not leave the reaio under dusty or wet [Link]’s very important for
users to understand all instruction knowledge before using the radio,please obey the local
legal rules.

Product Checking

Thanks for choosing our [Link] unbox and check whether the following accessories
are included and [Link] there’s anything missing or damaging after unboxed,please
contact your local distributor.

NO Item QTY

1 Device 1

2 Microphone 1

3 Holder 1

4 Screw 1

6 User Manual 1

7 Guarantee Card 1
Familiar with Radio
 Radio Keys Hand-MIC Keys Function

Short-press:lock/unlock the keypad

Long-press:Turn on/off the radio

ON/OFF/Volume
Clockwise:turn up the volume

Anti-clockwise:turn down the volume

Short-press:confirm setting or enter into menu

【—】 【MENU】 Long-press: enter into/exit DTMF input mode

DTMF Code ：A

AB Short-press:cancel setting or exit menu,switch working

frequency AB band
【--】 【EXIT】
Long-press:switch single/dual display

DTMF Code ：D

Short-press:switch frequency/channels/menu list upward

Long-press:fast switching of frequency/channels/menu list,FM

【︵】 【▲】
scanning upward

DTMF Code ：B

Short-press:switch frequency/channels/menu list downward

Long-press:fast switching of frequency/channels/menu list,FM

【︶】 【▼】
scanning downward

DTMF Code ：C

Short-press:switch from channel report methods to channel name

【└】
report or channel number report

【┘】 Short-press:switch channel mode or frequency mode

【P1】【P2】【P3】 Definable keys

Short-press:input digit 1

Long-press:enter/exit frequency input mode, which is used via

【1】 repeater

DTMF Code：1

Character Input:ASCII code (symbol,digit,letter)

Short-press:input digit 2
【2】
Long-press:switch from priority TX to edit or busy
 DTMF Code：2

Character Input：A B C a b c

Short-press:input digit 3

Long-press:turn on/off VOX

【3】
DTMF Code：3

Character Input：D E F d e f

Short-press:input digit 4

Long-press:Switch high/low power

【4】
DTMF Code：4

Character Input：G H I g h i

Short-press:input digit 5

Long-press:switch to squelch level

【5】
DTMF Code：5

Character Input：J K L j k l

Short-press:input digit 6

Long-press:turn on/off dual-band standby

【6】
DTMF Code：6

Character Input：M N O m n o

Short-press:input digit 7

Long-press:turn on/off backlight

【7】
DTMF Code：7

Character Input：P Q R S p q r s

Short-press: input digit 8

Long-press:shift to frequency space menu

【8】
DTMF Code：8

Character Input：T U V t u v

Short-press:input digit 9

Long-press:turn on/off keypad tone

【9】
DTMF Code：9

Character Input：W X Y Z w x y z

【0】 Short-press:input digit 0

 DTMF Code：0

Character Input：space key

Short-press:switch from channel report method to channel name

report or channel number report

【*】 Long-press:enter/exit FM radio

DTMF Code：*

Character Input:Delete Characters

Short-press:switch channel mode to frequency mode

Long-press:turn on Scan
【#】
DTMF: #

Character Input:turn on/off character inputting

Main PTT, press this button to transmit signals of the main

【PTT-1】
working frequency

【PTT-2】 Sub-PTT,press this button to transmit signals by B band frequency

4 Function and Operation

4.1 Transmitting Signal

Press [PTT-1]or[PTT-2]to transmit signals, icon ⑰turns red, and hand-mic light turns
grren.

Press [PTT-1]to transmit main working frequency signals, press [PTT-2]totransmit B band
frequency signals.

4.2 Receiving Signal

When the device receives same frequency signal with current working channel and the CTCSS

matches with each other’s, the radio will receive and send out the voice, and the icon ⑰

turns blue. If A band receives signals, hand-mic light turns green, while B band receives
signals, hand-mic lights turns blue.

4.3 Working Mode Switching

Short press 【#】 button to change the working mode to VFO frequency mode or Channel MODE. When it is

changed to VFO frequency mode, the icon ⑭ will show up as VHF; When it is changed to channel mode,the

icon ⑭ will show up as channel number.

4.4 Display Mode Switching

Short press 【EXIT】 key to turn on/off dual-band display. When turn off dual-band display, the

sub-frequency area will show are as system time.

4.5Frequency Changing and Repeater Frequency Setting

While under VFO mode, input frequencies manually via keypads, input 6 digits, the inputting is

[Link] this ,the input frequencies will be set to receiving and transmitting frequencies.

If need to use repeater to relay the signals, set the TX frequencies according to the repeater frequency

[Link]：Under VFO mode, long press 【1】 button, the frequency turns red, the input function

actives , and input 6 digits, so the inputting is done automatically. The input frequencies will set

to TX frequencies. Long press 【#】to exit TX frequency setting. Once the inputting is done , please

enter MENU list Save CH to save frequency to appointed channel.

Short press 【▲】/【▼】can switch preset working [Link] press 【▲】/【▼】is fast switching

function.

4.6Channel Switching

Under channel mode status, input channel number via keypads to switch to appointed channel

directly .Short press 【▲】/【▼】to switch to working channels one by one. Long press 【▲】/【▼】

is fast switching function.

4.7Air Band Receiving

 When the working frequency is set within the range of 108-136MHz, the device enters aviation

frequency receiving mode.

The device is not allowed to transmit signals under aviation frequency band status.

4.8Frequency Detecting and Decoding （One-click Decoding）

【P1】/【P2】/【P3】is set to Freq Detect, and press these definable buttons while it is under standby

status. Then the device begins to detecting and decoding. This function cannot detect CTCSS and

anti-decoded [Link] 【PTT】button to exit.

If the frequencies are changing constantly before detecting actives, which means the nearby

electromagnetic environment is complicated, in order to avoid strong electromagnetic interference,please

choose proper detecting place. After detecting is done, press 【MENU】to save the detected frequency

and CTCSS/DCS to current channel, and press 【PTT】to exit, press 【EXIT】to re-detect. If detecting

result is standard CTCSS/DCS, it will show up as standard CTCSS/DCS. If the result is non-standard

CTCSS/DCS,it will show up as “23b”or “24b” plus a series of digits. After saving, if you want to

check the result, please check Menu List Mute Code.

4.9 FM function

Long press 【*/FM】to enter into FM radio mode. Long press 【▲】/【▼】to search for signals, or

input frequencies manually via keypads. And short press 【▲】/【▼】to stop scanning.

If you want to receive signals while under FM radio mode, please check with MENU list FM Standby,

and turn it on.

4.10 NOAA

【P1】/【P2】/【P3】key to set to NOAA channels and press the side-key to NOAA weather report channels

under standby status. Press 【▲】/【▼】to switch NOAA channels. If not to operate for 2 seconds,the

device will scan NOAA channels automatically.

NOAA function is available in countries and areas that are supported only. The followings are 11
NOAA working frequencies.
1 162.55000M 7 162.52500M
2 162.40000M 8 161.65000M
3 162.47500M 9 161.77500M
 4 162.42500M 10 161.75000M
5 162.45000M 11 162.00000M
6 162.50000M

4.11 GPS(Optional)

While turn on GPS ON-OFF,the icon ⑦ shows up and the GPS actives.

Define 【P1】/【P2】/【P3】 as GPS, and press the button under standby interface, then enter into GPS

interface, which will show current longitude, latitude, height and the number of effective satellites.

Please use GPS at open area, if there are too many obstacles, GPS will drift and affect the positioning

accuracy.

Single radio measuring distance: when GPS is set successfully, press 【MENU】key,to set current

position as the starting,then move to other positions, once the GPS settles down, press 【#】key then

will show up the orientation and distance from the starting to the final position.

GPS sending: turn on GPS in menu list GPS ON-OFF-ON; or list Roger Beep-choose Send GPS . When GPS

is set successfully, press 【PTT】to send local longitude and latitude to receiving part. When the GPS

of receiving is turned on and set successfully, the receiving radio will show up the orientation and

distance of transmitting radio. While the GPS of receiving is turned off or be set unsuccessfully,the

receiving radio will show up the longitude and latitude of transmitting radio.

4.12Inputting Method

You can change relative characters via inputting method both in Menu list Personal ID and Menue

list CH Name.

4.12 .1 Delete Character

when in Person ID, the display content will be added blank characters automatically to 16
bytes( 2 bytes per Chinese character,1 byte per Digit/English letter/symbol). while in
Channel Name, the display content will be added blank characters automatically to 10 bytes.
You can move the cursor via 【▲】or【▼】to certain place, then press 【*】to delete the characters
before it.

4.12 .2 Inputting of Digit/Symbol/English Letter

 When in Personal ID or CH Name status, input numeric keys directly to finish the numeric inputting.

Press 【#】button to input English letter, press relative keys to complete the inputting.

Steps to input characters

[Link]【#】key to start inputting

[Link]【1】key,open ASCII code table(the table consists of digits/symbols/English letters , and

the initial character is blank character)

[Link]【▲】or【▼】key to find the needed characters.

[Link] the digit key which holds the characters to complete the inputting.

The match-up relationship of digit keys and letters

【1 Characters】 【2 ABC】 【3 DEF】

【4 GHI】 【5 JKL】 【6 MNO】

【7 PQRS】 【8 TUV】 【9 WXYZ】

Functions of Definable Keys

To define 【P1】/【P2】/【P3】functions in Menu, the following are side-key functions:

1. off:press defined key , and nothing happen

2. Monit:to monitor the signal of working frequency, and ignore the TX/RX sub-tone setting, force to

turn on squelch.

3. Freq Detect:to detect frequencies and CTCSS of nearby radios.

4. Repeat Mode:to switch working mode from talk around mode (TX amd RX at the same frequency , and the

icon ⑥ shows up as RR)to reverse frequency (reverse TX/RX frequencies,and the icon ⑥ shows up as TR).

5. Preset CH: to fast switching from current channel to preset shortcut channels. Shortcut channels are
set by software.

6. Local Alarm: to give out emergency alarm and report to surroundings at the same time.

7. Remote Alarm: to give out emergency alarm and transmit the alarm via main working frequency.

8. NOAA CH: to enter/exit NOAA weather report channels.

9. Send Tone:to transmit a fixed frequency Tone via main working mode. The tone is set by software.

10. Roger Beep: to change end tones.

11. GPS: to enter/exit GPS status.

Instruction of Menu

【startup logo】to turn on/off the image of startup

【ringtone】to turn on/off startup tone

【prompt text】to turn on/off startup greeting

【key beep】to turn on/off keypad tone

【roger beep】to turn on/off TX end tone

【dual display】to turn on/off dual display

【TX priority】to switch priority transmitting to edition mode or busy mode. If set to edition mode

the radio transmits the signal under main channels. If set to busy mode, the main channel is set to the

receiving channel to transmit signals under receiving.

【freq step】to set frequency switching and scanning frequency step

【SQ level】to set SQ level

【LED timer】to set backlight time

【TOT】to set the max TX time.

【VOX level】to set VOX level

【VOX delay】to set VOX delay time

【NOAA Monitor】to turn on/of NOAA monitor.

 【FM Standby】to turn on/off main frequency receiving function while in FM status.

【Tail Tone】to turn off/on tail tone.

【scan DIR】to set scan direction.

【scan mode】TO:to continue to scan after receiving.

CO:start to scan once the signal gone.

SE：stop scanning after receiving signal.

【scan timer】to set standing time.

【scan end】to exit scan.

【Personal ID】to set local ID.

【Repeater Mode】to change working mode to talk around or reverse frequencies.

【CTCSS/DCS】 to set the sub-tones of TX/RX frequency,switching sub-tone mode via 【*】key,press

【▲】or【▼】to switch sub-tones.

【RX CTCSS/DCS】to set RX CTCSS/DCS of main frequency.

【TX CTCSS/DCS】to set TX CTCSS/DCS of main frequency.

【TX Power】to set High/Low power of transmitting.

【Band Width】to set Narrow/Wide band .

【Busy Lock】to set busy [Link] carriers match,and the channel is not allowed to transmit no matter

their CTCSS/DCS matches or not. If CTCSS/DCS matches successfully, the radio is not allowed to transmit.

【Scrambler】to set voice scrambler number on main frequencies, if the number is 0, the scrambler is

turned off.

【DCS Encrypt】When there is digital sub-tones on main frequencies,turn on encryption function will

re-encrypt to digital sub-tones. Only supported to digital sub-tones.

【Mute Code】This is non-standard DCS, can be defined to 23 or 24 digits. Press the 【▲】or【▼】to

choose CTCSS mode, input digits to become non-standard DCS code. The saved non-standard DCS code can

be checked in this list.

【CH Name】to set channel name of main frequency.

【Save CH】Copy and save information of current channel to appointed channels. The CH-XXX N/Y shows

up when enter the list. N means empty channel. Y means not empty [Link] input the digits manually

to shift to appointed channel.

【Delete CH】to delete information of appointed [Link] input the digits manually to shift to appointed

channel.

【RX record】to turn on/off RX record.

【TX record】to turn on/off TX record.

【record log】to check recorded voice, and the recording shows up as “sequence number+ channel

number+recording duration + recording time”. Red characters means to transmit recording, blue characters

means to receive recording. Press 【*】to delete current recording. Press 【#】to play current recording.

Note：do not remove the TF card arbitrarily, or the recording will not match.

【GPS】to turn on/off GPS.

【GPS Monit】if the radio has GPS, please turn on the GPS and GPS monit, the radio will send the GPS

module to the connected computer. The data can be parsed via GPS monitor software or port instrument.

The Bard rate of programming cable is Normal mode 115200, slow mode 19200. please turn off this rate

while write or read data, or it will fail to write or read.

【UTC area】to set UTC area to match local time.

【APO】to set shutoff time to reduce power consumption.

【Initialize】to initialize the radio to the last writing status.

【Version】to check firmware version and version date.

【Instruction】to scan QR code to check with user manual.

Specifications
General Part
Frequency Range RX : 64-108MHz(FM band,should be turned on while
use)
Scanning: 108-520MHz
TX : 144-148MHz/420 - 450MHz (Amateur radio)

Channel Capacity 999

Channel Spacing（W/N） 25kHz/12.5kHz
Voltage 13.8V DC
Working Mode Same frequency simplex,different frequency simplex
Antenna Removable Antenna
Frequency Stability ≤5ppm
Working Temperature －20 ~ ＋60℃
Dimension 126 X 100 X 40 without holderabout455g without holder
Transmitting Part
Modulation Mode F3E
Maximum deviation（W/N） ≤5KHz /≤2.5KHz
SNR（W/N） -45dB/ -40dB
Modulation distortion ＜7％
Spurious emission ≤-13DB
TX Current ≤4A
Receiving Part
Sensitivity（W/N） 0.22μV/ 0.25μV 12dB SINAD
Inter modulation（W/N) 65dB/ 60dB
Audio Distortion ＜5％
Audio Output Power ≤3W（16Ω）
RX Current ≤500mA
Standby Current ≤70mA
Note: The above parameters are subject to change without prior notice!
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This equipment should be installed and operated with minimum distance 100cm between the radiator& your body.