2/1/23, 11:35 SIS 2.
2022/11/21 Maintenance Interval Schedule (M0136698-01)
SMCS - 7000 i09659649
Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance
procedures are performed.
PPS
The user is responsible for the performance of maintenance. All adjustments, the use of proper lubricants, fluids, filters, and the replacement of
components due to normal wear and aging are included. Failure to adhere to proper maintenance intervals and procedures may result in
-
diminished performance of the product and/or accelerated wear of components.
202 000A
Products that operate in severe operating conditions or that experience abnormally high fuel consumption, may require more frequent
3
maintenance. Refer to the maintenance procedure for any other exceptions that may change the maintenance intervals.
14: /01/0 3150
Note: The aftertreatment system can be expected to function properly for the useful life of the engine (emissions durability period), as defined by
regulation. All prescribed maintenance requirements must be followed.
3
M0 :58- 4 2
Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.
1 0
The following guidelines should be followed if the service hours are not met:
3
© 2 669 3:00
Items listed between 10 and 100 service hours should be performed at least every 3 months.
0 8
Items listed between 250 and 500 service hours should be performed at least every 6 months.
Cat 3 C2
Items listed between 1000 service hours and 2500 service hours should be performed at least every year.
When Required
Battery or Battery Cable - Replace
e r a
Con pilla terpi
fide r: llar
Bottom Guards - Clean
Camera - Clean/Adjust
Cooler Cores and A/C Condenser - Clean
ntia
Cooling System Water Temperature Regulator - Replace
Inc
Cutting Edges and End Bits - Inspect/Replace
lG
Engine Air Filter Primary and/or Secondary Element - Clean/Replace .
Engine Air Precleaner - Clean
ree
n
Ether Starting Aid Cylinder - Replace
Film (Product Identification) - Clean
Front Idler Position - Check
Fuel System - Prime
Fuel Tank Cap Filter and Strainer - Replace/Clean
Fuses and Circuit Breakers - Replace/Reset
Hydraulic System Filter Screens - Clean
Oil Filter - Inspect
Power Train Scavenge Screen - Clean
Radiator Core - Clean
Radiator Pressure Cap - Clean/Replace
Refrigerant Dryer - Replace
Ripper Tip and Shank Protector - Inspect/Replace
Torque Converter Scavenge Screen - Clean
Trunnion Bearing - Adjust
Winch Wire Rope - Install
Window Washer Reservoir - Fill
Window Wipers - Inspect/Replace
Windows - Clean
Every 10 Service Hours or Daily
Backup Alarm - Test
Braking System - Test
Cab Filter (Fresh Air) - Clean/Inspect/Replace
Cooling System Coolant Level - Check
Engine Oil Level - Check
Fuel Tank Water and Sediment - Drain
Horn - Test
[Link] 1/3
2/1/23, 11:35 SIS 2.0
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Pivot Shaft Oil Level - Check
Power Train System Oil Level - Check
Seat Belt - Inspect
Undercarriage - Clean
Every 50 Service Hours
Bulldozer Tilt Brace and Tilt Cylinders - Lubricate
Cab Filter (Recirculation) - Clean/Inspect/Replace
Lift Cylinder Yoke Bearings - Lubricate
Ripper Linkage and Cylinder Bearings - Lubricate
Track Pins - Inspect
Every 250 Service Hours
Engine Oil Sample - Obtain
Equalizer Bar End Pins Oil Level - Check
Final Drive Oil Level - Check
Fuel Tank Water and Sediment - Drain
Pivot Shaft Oil Level - Check
Track - Check/Adjust
Winch Fairlead Rollers - Lubricate
Winch Oil and Breather - Change/Clean
Winch Oil Level - Check
Every 500 Service Hours
Belt - Inspect/Adjust/Replace
Cab Filter (Fresh Air) - Clean/Inspect/Replace
Cab Filter (Recirculation) - Clean/Inspect/Replace
Coolant Sample (Level 1) - Obtain
Engine Crankcase Breather - Clean
Engine Oil and Filter - Change
Final Drive Oil Sample - Obtain
Final Drive Seal Guard - Inspect/Clean
Fuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap Filter and Strainer - Replace/Clean
Hydraulic System Oil Sample - Obtain
Power Train Breather - Clean
Power Train System Oil Sample - Obtain
Recoil Spring Compartment Oil Level - Check
Every 1000 Service Hours
Battery - Inspect
Cab Filter (Fresh Air) - Clean/Inspect/Replace
Power Train Breather - Clean
Power Train Oil Filter - Replace
Power Train System Oil And Screens - Change/Clean
Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
Steering Charge Filter - Replace
Torque Converter Scavenge Screen - Clean
Winch Oil and Breather - Change/Clean
Every 2000 Service Hours
Cooling System Coolant Sample (Level 2) - Obtain
Engine Mounts and Equalizer Bar - Inspect
Final Drive Oil - Change
Final Drive Seal Guard Packing - Replace
Hydraulic System Oil - Change
Radiator Guard Pin Joint - Inspect
[Link] 2/3
2/1/23, 11:35 SIS 2.0
Refrigerant Dryer - Replace
Track Roller Frame - Inspect
Track Roller Frame Guides - Inspect
Every 2500 Service Hours
Electronic Unit Injector - Inspect/Adjust
Engine Valve Lash - Check/Adjust
Every 3 Years
Seat Belt - Replace
Every 6000 Service Hours
Cooling System Coolant Extender (ELC) - Add
Every 12 000 Service Hours
Cooling System Coolant (ELC) - Change
PPS-000A3150
2023/01/02
[Link]-03:00
i09659649
© 2023 Caterpillar Inc.
Caterpillar:
Confidential Green
[Link] 3/3
