GEOFLEX
Marking
Reference standard:
EN14891
ONE-COMPONENT, FLEXIBLE, GEOPOLYMER WATERPROOFING, FOR NEW
WATERPROOFING AND REPAIRS, EVEN ON TOP OF EXISTING LAYERS
Waterproofing mortars
GRANTS LEED CREDITS
CHARACTERISTICS ENVIRONMENTAL METHOD OF USE PRECAUTIONS
ONE-COMPONENT WATERPROOF ECO GREEN MIX APPLY BY STORAGE:
MECHANICALLY INOX SPATULA IN A DRY PLACE
PROBLEM SOLUTION APPLICATION FIELDS
WATERPROOFING, GEOFLEX is a pre-mixed powder based on GEOFLEX can be used for waterproofing under
EVEN ON TOP special hydraulic binders and synthetic resins tiles on terraces, balconies, swimming pools,
OF EXISTING which, when mixed with clean water, provides tubs and baths.
LAYERS: a spreadable mortar with high adhesion to all of GEOFLEX can also waterproof interior and
the most common building supports. exterior floors and walls, also on top of existing
ceramic surfaces.
GEOFLEX can be covered with ceramics glued
with class C2 adhesives or with suitable exterior
grade paints and varnishes.
BALCONIES TERRACES ADVANTAGES
• High adhesion.
CM
G TO
EU R O P E
AN
• Highly water repellent.
DIN
EN • Highly compatible with many applications and
G
OR
NO
AC C
RMS
coatings.
14891 O1P • Easy application.
UNDER-TILE WATERPROOFING
CEMENT-POLYMER BASE • Ecological and fully recyclable.
SWIMMING POOLS AND TUBS BATHS AND SHOWERS WATERPROOFING
METHOD OF USE
• SUBSTRATE PREPARATION for too long so as not to let air into the mix. RASANTI onto the first coat of GEOFLEX.
Existing concrete or mortar surfaces must be • APPLICATION
cleaned thoroughly to remove dust, grease, sur- Spread GEOFLEX with a stainless steel float
facing salts, algae and dirt in general. For crum- or squeegee onto the clean surface until the (See following)
bling or gypsum or anhydrite surfaces, treat first desired thickness of max 3 mm is obtained with
with PRIMER FIX (1). Self adhesive sealing tape two coats (3). For good waterproofing quality, 3
COVERBAND ADHESIVE to be applied on any the product must be applied in a single coat
edge and sectioning joint (2). until the minimum recommended thickness of
• MIX PREPARATION 2 mm is obtained. Avoid thicknesses of over 3
GEOFLEX is prepared by mixing the product mm, to limit the drying times and so as not to
with right quantity clean water (see table). make the waterproofing layer too rigid.
Pour the powder product into the water and For surface areas over 10 m² it is recommended
mix with a drill on low speed until a uniform to apply a fibreglass reinforcement net with
paste is obtained with no lumps. Do not mix mesh size 4×4 mm such as RETINVETRO PER
1 2 4
5th DIVISION
TECHNICAL CHARACTERISTICS
Standard GEOFLEX
Appearance Powder
Colour Beige
Apparent volume mass EN 1015-6 1.02 ± 0.03 kg/L
Water ratio 19% ± 1%
Storage in original packaging in a dry place 12 months
Mix properties and workability
Volume mass of the mix 1.50 ± 0.05 kg/L
Durata impasto lavorabile (*) approx 45 minutes
Minimun application thickness 2 mm
Maximum application thickness 3 mm (in two coats)
Adhesive class for application of ceramic C2, according EN 12004:2007+A1:2012
Waiting time - for applying each coat over the previous one (*) minimun 6 hours
Waiting time - for overpainting with ceramic or paints (*) approx 24 hours
7 days
Waiting time - per la messa in servizio (*)
14 days (permanent water)
Temperature application +5°C ÷ +35°C
Application manual
Performance characteristics Standard Product performance
Class and type EN 14891 CM O1P
Initial adhesion strength - after 28 days EN 14891 ≥2.00 N/mm²
Adhesion strength - after chlorate water dipping EN 14891 ≥0.80 N/mm²
Adhesion strength - after heat EN 14891 ≥2.00 N/mm²
Capillary absorption and water permeability EN 7783 5 m < Sd < 10 m - class II
CO2 permeability EN 1062-6 Sd >50 m
the numerous possible uses and the possible interference of conditions or
elements beyond our control, we assume no responsibility regarding the results
which are obtained. The purchasers, of their own accord and under their own
responsibility, must establish the suitability of the product for the envisaged use.
Watertightness EN 14891 no penetration
Crack bridging EN 1062-7 >0.75 mm – class A3
Crack bridging ability a –5°C EN 14891 >0.75 mm
Thermal resistance - Working temperature –30°C ÷ +90°C
Fire reaction EN 13501-1 E
Hazardous substances EN 14891 According note in ZA.1
Test conditions: temperature 23±2°C, 50±5% R.H. and air velocity in test area <0.2 m/s. The data shown may vary depending on the specific work site conditions: temperature,
humidity, ventilation, absorbency of the base coat. (*) The stated times are longer or shorter as the temperature decreases or increases.
In accordance with the general principles defined in EN 14891 - Principles for evaluation of the use of products and systems.
(See previous)
The second coat will cover the reinforcement • Do not prepare the mix manually.
net. • For waterproofing systems with negative
• CONSUMPTION thrust use OSMOSEAL.
Approximately 1.1 kg/m² x mm. • Protect from rain while the product is set-
Average recommended yield 2.2 kg/m²×2 mm. ting.
• Clean the tools with water immediately
• PRECAUTIONS after use.
• Avoid application in strong sunlight and at
high temperatures.
• Do not use on metal or rubber surfaces
or on vinyl, wood, linoleum or PVC floors.
The advice and technical information provided, is what results from our best
and may be changed or updated by INDEX at any time without previous warning.
The figures shown are average indicative figures relevant to current production
knowledge regarding the properties and the use of the product. Considering
• Do not apply at temperatures below +5°C.
• Store the product in cool, dry conditions in
the original closed containers.
• Do not add cement or aggregates to the
mix.
• Do not apply with thicknesses of over 2
mm.
PACKAGING
15-kg-Sack
• FOR ANY FURTHER INFORMATION OR ADVICE ON PARTICULAR APPLICATIONS, CONTACT OUR TECHNICAL OFFICE • IN ORDER TO CORRECTLY USE OUR PRODUCTS, REFER TO INDEX TECHNICAL SPECIFICATIONS •
Internet: [Link]
Informazioni Tecniche Commerciali
tecom@[Link]
Amministrazione e Segreteria
1/2017ing-5/2016
Pu./dig.- 500
index@[Link]
Via G. Rossini, 22 - 37060 Castel D’Azzano (VR) - Italy - C.P.67 Index Export Dept.
T. +39 045 8546201 - F. +39 045 518390 [Link]@[Link] “GBC Italia” Associated
© INDEX
