SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T.

GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 1 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Permanent Facility
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
1 Digital Multimeter by 1 mA to 100 mA 0.200 % to 0.176 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
2 Digital Multimeter by 100 µA to 1 mA 0.375 % to 0.20 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
3 Digital Multimeter by 100 mA to 10 A 0.176 % to 0.223 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using High Voltage
Alternating AC High Voltage @
4 Probe with DMM By 1 kV to 30 kV 11.25 % to 3.07 %
Current (< 1 50Hz
Comparison Method
GHz)
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 2 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
5 Digital Multimeter by 1 V to 10 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
6 Digital Multimeter by 10 V to 100 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
7 Digital Multimeter by 100 mV to 1 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
8 Digital Multimeter by 100 V to 750 V 0.084%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
9 Alternating AC Current (50 Hz ) Function Calibrator 100 mA to 2 A 0.36 % to 0.41 %
Current (< 1 By Direct Method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 3 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 5 ½ digit
TECHNICAL-
Multi-Function
10 Alternating AC Current (50 Hz ) 2 A to 10 A 0.41 % to 0.33 %
Calibrator By Direct
Current (< 1
Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
11 Alternating AC Current (50 Hz ) Function Calibrator 200 µA to 100 mA 0.40 % to 0.36 %
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO- Using 5½ digit Multi-
TECHNICAL- Function Calibrator
AC High Current (50
12 Alternating & 100 turn Current 10 A to 900 A 2.01 % to 0.98 %
Hz )
Current (< 1 Coil By Direct
GHz) (Source) Method
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
13 Alternating Function Calibrator 100 mV to 100 V 1.91 % to 0.22 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
14 Alternating Function Calibrator 100 V to 1000 V 0.22 % to 0.20 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
15 Alternating Function Calibrator 5 mV to 100 mV 3 % to 1.91 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 4 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Decade
Capacitance
16 Alternating Capacitance Box By 1 nF to 100 µF 1.20 % to 1.22 %
(@1kHz)
Current (< 1 Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Decade
Inductance (@ 1
17 Alternating Inductance Box By 100 µH to 100 mH 1.16%
kHz)
Current (< 1 Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 6½ Digit
18 DIRECT DC Current Digital Multimeter by 1 A to 10 A 0.100 % to 0.163 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
19 DIRECT DC Current Digital Multimeter by 1 mA to 100 mA 0.06%
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
20 DIRECT DC Current Digital Multimeter by 10 µA to 100 µA 0.30 % to 0.06 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
21 DIRECT DC Current Digital Multimeter by 100 µA to 1 mA 0.06%
CURRENT Direct Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 5 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digit
22 DIRECT DC Current Digital Multimeter by 100 mA to 1 A 0.06 % to 0.10 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using High Voltage
23 DIRECT DC High Voltage Probe with DMM By 1 kV to 30 kV 11.78 % to 4.19 %
CURRENT Comparison Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
24 DIRECT DC Voltage Digital Multimeter by 1 V to 1000 V 0.005 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
25 DIRECT DC Voltage Digital Multimeter by 10 mV to 100 mV 0.44 % to 0.01 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
26 DIRECT DC Voltage Digital Multimeter by 100 mV to 1 V 0.01 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
1 Mega ohm to 10
27 DIRECT Resistance (2wire) Digital Multimeter by 0.015 % to 0.03 %
Mega ohm
CURRENT Direct Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 6 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digit
10 Mega ohm to 100
28 DIRECT Resistance (2wire) Digital Multimeter by 0.03 % to 0.38 %
Mega ohm
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
29 DIRECT Resistance (4 wire) Digital Multimeter by 1 k ohm to 10 k ohm 0.011%
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
10 k ohm to 100 k
30 DIRECT Resistance (4 wire) Digital Multimeter by 0.011%
ohm
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
31 DIRECT Resistance (4 wire) Digital Multimeter by 100 ohm to 1 k ohm 0.1 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
32 DIRECT DC Current Function Calibrator 0.2 mA to 100 mA 5.9 % to 0.15 %
CURRENT By Direct Method
(Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
33 DIRECT DC Current Function Calibrator 1 A to 10 A 0.15 % to 0.23 %
CURRENT By Direct Method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 7 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 5½ digit Multi-
34 DIRECT DC Current Function Calibrator 100 mA to 1 A 0.14 % to 0.25 %
CURRENT By Direct Method
(Source)
ELECTRO- Using 5½ digit Multi-
TECHNICAL- Function Calibrator
35 DIRECT DC High Current & 100 turn Current 10 A to 900 A 2.67 % to 0.81 %
CURRENT Coil By Direct
(Source) Method
ELECTRO-
TECHNICAL- Using 5½ digit Multi- 3.0 %
36 DIRECT DC Voltage Function Calibrator 0.5 mV to 100 mV
CURRENT By Direct Method to 1.2 %
(Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
37 DIRECT DC Voltage Function Calibrator 100 mV to 100 V 0.12%
CURRENT By Direct Method
(Source)
ELECTRO-
TECHNICAL- Using 6½ Digit
38 DIRECT DC Voltage Digital Multimeter by 100 V to 1000 V 0.13%
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using High
5 Mega ohm to 100
39 DIRECT High Resistance Resistance Jig By 2.38 % to 5.78 %
Giga Ohm
CURRENT Direct Method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 8 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Decade
40 DIRECT Resistance Resistance Box By 1 ohm to 10 ohm 0.86 % to 0.15 %
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
10 k ohm to 10
41 DIRECT Resistance Resistance Box By 0.12 % to 0.13 %
Mega ohm
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
42 DIRECT Resistance Resistance Box By 10 ohm to 10 kohm 0.15 % to 0.12 %
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
10 Mega ohm to
43 DIRECT Resistance Resistance Box By 0.13 % to 2.48 %
1000 Mega ohm
CURRENT Direct Method
(Source)
ELECTRO-
Using Precision
TECHNICAL-
B Type Digital Thermometer
44 TEMPERATURE 400 °C to 1800 °C 0.70°C
Thermocouple By Simulation
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
E Type Digital Thermometer
45 TEMPERATURE -200 °C to 1000 °C 0.90°C
Thermocouple By Simulation
SIMULATION
Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 9 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using Precision
TECHNICAL-
Digital Thermometer
46 TEMPERATURE J Type Thermocouple -200 °C to 1200 °C 0.1°C
by Simulation
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
K Type Digital Thermometer
47 TEMPERATURE -200 °C to 1370 °C 0.13 °C
Thermocouple by Simulation
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
L Type Digital Thermometer
48 TEMPERATURE -200 °C to 900 °C 0.81°C
Thermocouple by Simulation
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
N Type Digital Thermometer
49 TEMPERATURE -200 °C to 1300 °C 0.08°C
Thermocouple by Simulation
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
R Type Digital Thermometer 0
50 TEMPERATURE 0.31°C
Thermocouple by Simulation to 1750 °C
SIMULATION
Method
(Measure)
ELECTRO-
Using Precision
TECHNICAL-
Digital Thermometer
51 TEMPERATURE RTD PT 100 -200 °C to 800 °C 0.94°C
By Simulation
SIMULATION
Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 10 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using Precision
TECHNICAL-
S Type Digital Thermometer 0
52 TEMPERATURE 0.31 °C
Thermocouple by Simulation to 1750 °C
SIMULATION
Method
(Measure)
ELECTRO- B Type
TECHNICAL- Thermocouple Using Process
53 TEMPERATURE (Temperature Source By 600 °C to 1800 °C 1.83 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- E Type
TECHNICAL- Thermocouple Using Process
54 TEMPERATURE (Temperature Source By -200 °C to 1000 °C 0.70°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO-
J Type Thermocouple
TECHNICAL- Using Process
(Temperature
55 TEMPERATURE Source By -200 °C to 1200 °C 0.70°C
Indicator / controller
SIMULATION Simulation Method
/ recorder)
(Source)
ELECTRO- K Type
TECHNICAL- Thermocouple Using Process
56 TEMPERATURE (Temperature Source by -200 °C to 1370 °C 0.80 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- L Type
TECHNICAL- Thermocouple Using Process
57 TEMPERATURE (Temperature Source by -200 °C to 900 °C 0.81°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 11 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- N Type
TECHNICAL- Thermocouple Using Process
58 TEMPERATURE (Temperature Source by -200 °C to 1300 °C 1.29°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- R Type
TECHNICAL- Thermocouple Using Process
0
59 TEMPERATURE (Temperature Source by 1.83°C
to 1750 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO-
RTD PT 100
TECHNICAL- Using Process
(Temperature
60 TEMPERATURE Source by -200 °C to 800 °C 0.94 °C
Indicator / controller
SIMULATION Simulation Method
/ recorder)
(Source)
ELECTRO- S Type
TECHNICAL- Thermocouple Using Process
0
61 TEMPERATURE (Temperature Source by 1.83°C
to 1750 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- U Type
TECHNICAL- Thermocouple Using Process
62 TEMPERATURE (Temperature Source by -200 °C to 600 °C 0.81°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO-
TECHNICAL- Using 6½ Digit
63 TIME & Frequency Digital Multimeter by 45 Hz to 1 kHz 0.13 % to 0.014 %
FREQUENCY Direct Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 12 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Time Interval
64 TIME & Stop Watch/ Timer Meter by 5 s to 24 hr 2.69 % to 0.36 %
FREQUENCY Comparison Method
(Measure)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
65 TIME & Frequency Function Calibrator 50 Hz to 1 kHz 0.30 % to 0.20 %
FREQUENCY By Direct Method
(Source)
Using Digital
MECHANICAL- Digital Tachometer with
100 rpm to 5000
66 ACCELERATION Tachometer(Non- rpm source. As per 2.1% rdg
rpm
AND SPEED Contact Type) Sanas TR-45-01 by
Comparison Method:
Using Digital
MECHANICAL- RPM Meter/
Tachometer as per 5000 rpm to 90000
67 ACCELERATION Centrifuge / (Non- 0.40% rdg
Sanas TR-45-01 by rpm
AND SPEED Contact Type)
Comparison Method
Using Digital
MECHANICAL- RPM Meter/
Tachometer as per
68 ACCELERATION Centrifuge / (Non- 10 rpm to 100 rpm 6.0% rdg
Sanas TR-45-01 by
AND SPEED Contact Type)
Comparison Method
Using Digital
MECHANICAL- Tachometer with
Tachometer
69 ACCELERATION rpm source. As per 10 rpm to 100 rpm 10% rdg
(Contact Type)
AND SPEED Sanas TR-45-01 by
Comparison Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 13 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Digital
MECHANICAL- Tachometer with
Tachometer 100 rpm to 4000
70 ACCELERATION rpm source as per 2.2% rdg
(Contact Type) rpm
AND SPEED Sanas TR-45-01 by
Comparison Method
Using Sound Level
MECHANICAL- Sound Level Meter
71 calibrator by 114 dB 1.79dB
ACOUSTICS (Frequency- 1 kHz)
Comparison Method
Sound Level Using Sound Level
MECHANICAL-
72 Meter(Frequency- 1 calibrator by 94 dB 1.76dB
ACOUSTICS
kHz) Comparison Method
using standard
density hydrometer
MECHANICAL-
Density Hydrometer as per comparison 0.650 g/ml to 1.000
73 DENSITY AND 0.0114g/ml
L.C.-0.001 g/ml method procedure g/ml
VISCOSITY
based on IS 3104
(Part-1)
Using standard
density hydrometer
MECHANICAL-
Density Hydrometer as per comparison 1.000 g/ml to 2.000
74 DENSITY AND 0.015g/ml
L.C.-0.001 g/ml method procedure g/ml
VISCOSITY
based on IS 3104
(Part-1)
MECHANICAL-
DIMENSION Bevel Protractor /
Using Profile
(BASIC Angular Protractor / 0°
75 Projector by 1.8min
MEASURING Combination Set, to 180 °
Comparison Method
INSTRUMENT, L.C.-5 min
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 14 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Digimetic
(BASIC Cube Mould
76 Caliper by Upto 150 mm 30 µm
MEASURING (Diameter)
Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Gauge Block
(BASIC Depth Micrometer
77 Set Surface Plate By 0 to 150 mm 8.6µm
MEASURING L.C.-0.01mm
Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
0
DIMENSION
Using Gauge Block
(BASIC Depth Vernier
78 Set Surface Plate By 19.9µm
MEASURING L.C.-0.02mm
Comparison Method
INSTRUMENT,
to 300 mm
GAUGE ETC.)
MECHANICAL-
DIMENSION
(BASIC Dial Gauge(Lever Using ULM by 0
79 1.0µm
MEASURING Type) L.C.-0.001 mm comparison Method to 0.14 mm
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
(BASIC Dial Gauge(Lever Using ULM By
80 0 to 0.8 mm 5.8µm
MEASURING Type) L.C.-0.01 mm Comparison Method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 15 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Dial Indicator Using Gauge Block
(BASIC
81 (Plunger Type) Set Surface Plate By 0 to 10 mm 5.47µm
MEASURING
L.C.-0.001 mm Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Dial Indicator Using Gauge Block
(BASIC
82 (Plunger Type) Set Surface Plate By 0 to 50 mm 8.2µm
MEASURING
L.C.-0.01 mm Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Gauge Block
Dial Indicator
(BASIC Set and Surface
83 (Plunger Type) 0 to 25 mm 10.62µm
MEASURING Plate by Comparison
L.C.-0.01 mm
INSTRUMENT, Method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Dial Thickness Using Gauge Block
(BASIC
84 Gauge (Length) Set (“0” Grade) by 0 to 10 mm 12.4 µm
MEASURING
L.C.-0.01 mm comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Dial Thickness Using Gauge Block
(BASIC
85 Gauge(Length) Set(“0” Grade) By 0 to 10 mm 10µm
MEASURING
L.C.-0.001 mm Comparison Method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 16 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using digimatic
(BASIC Elongation Gauge/
86 caliper by upto 100 mm 25µm
MEASURING Flankiness Gauge
Comparison Method
INSTRUMENT,
GAUGE ETC.)
Using Gauge Block
MECHANICAL-
Set /Long Gauge
DIMENSION
Block set, Surface
(BASIC External Micrometer
87 Plate, optical flat , 0 to 150 mm 2.5µm
MEASURING L.C.-0.001 mm
set of 4 optical
INSTRUMENT,
parallels by
GAUGE ETC.)
comparison method
Using Gauge Block
MECHANICAL-
Set /Long Gauge
DIMENSION
Block set, Surface
(BASIC External Micrometer
88 Plate, optical flat, 150 mm to 300 mm 9.43µm
MEASURING L.C.-0.001 mm
set of 4 optical
INSTRUMENT,
parallels by
GAUGE ETC.)
comparison method
Using Gauge Block
MECHANICAL-
Set /Long Gauge
DIMENSION
Block set, Surface
(BASIC External Micrometer
89 Plate optical flat , 0 to 600 mm 11.7µm
MEASURING L.C.-0.01 mm
set of 4 optical
INSTRUMENT,
parallels by
GAUGE ETC.)
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 17 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Digital
(BASIC
90 Feeler Gauge Micrometer by 0.05 mm to 1 mm 8.89µm
MEASURING
comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
Using Gauge Block
DIMENSION
Height Gauge Set /Long Gauge
(BASIC
91 (Dial/Digital/Analog) Block set, Surface 0 to 600 mm 14.0µm
MEASURING
L.C. 0.01mm Plate by comparison
INSTRUMENT,
method
GAUGE ETC.)
MECHANICAL-
Using Gauge Block
DIMENSION
Internal Micrometer/ Set, Surface Plate,
(BASIC
92 Stick Micrometer Slip Gauge 5 mm to 1000 mm 11.2µm
MEASURING
L.C.-0.01 mm Accessory set By
INSTRUMENT,
Comparison Method
GAUGE ETC.)
MECHANICAL- Measuring Pin/
DIMENSION Thread Measuring
(BASIC Pin (Actual diameter Using ULM by 0.170 mm to 6.350
93 1.5µm
MEASURING of individual wire, Comparison Method mm
INSTRUMENT, Uniformity of
GAUGE ETC.) diameter)
MECHANICAL-
DIMENSION
Using Scale & Tape
(BASIC Measuring Tape 289*SQRT Lµm (L is
94 Calibrator by 0 to 50 m
MEASURING L.C.-1 mm in m)
comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 18 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Scale & Tape
(BASIC 560*sqrt L µm (L is
95 Pie Tape Calibrator by 60 mm to 950 mm
MEASURING in mtr)
comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using ULM and
Plain Plug Gauge
(BASIC master Plug Gauge
96 (Diameter at 4 5 mm to 150 mm 2.5µm
MEASURING by Comparison
position)
INSTRUMENT, Method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using ULM and
Plain Ring Gauge
(BASIC Master Ring Gauge
97 (Diameter at four 5 mm to 100 mm 3µm
MEASURING by comparison
position)
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Radius Gauge( Using Profile
(BASIC
98 concave and convex Projector By c by 1.0 mm to 25 mm 231.26µm
MEASURING
profiles) Radius comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using ULM and
Snap Gauge/Gap
(BASIC Master Ring Gauge
99 Gauge (Diameter at 15 mm to 100 mm 1.2µm
MEASURING by comparison
4 position)
INSTRUMENT, method
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 19 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Scale & Tape
(BASIC
100 Steel Scale L.C-1mm Calibrator by 0 to 1000 mm 356µm
MEASURING
comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Profile
(BASIC Test Sieves
101 Projector By 0.045 mm to 1 mm 8.86µm
MEASURING (Aperture size)
Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Profile
(BASIC Test Sieves Projector Digital
102 1 mm to 25 mm 16.3µm
MEASURING (Aperture size) Caliper By
INSTRUMENT, Comparison Method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Profile
(BASIC Test Sieves Projector Digital
103 25 mm to 100 mm 21.6µm
MEASURING (Aperture size) Caliper By
INSTRUMENT, Comparison Method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Profile
(BASIC Thread Pitch Gauge
104 Projector By 0.4 mm to 6.0 mm 18.7µm
MEASURING (Pitch, Flank Angle)
Comparison Method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 20 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION Using ULM and
Thread Plug Gauge
(BASIC Measuring wire set
105 (Major Diameter 5 mm to 100 mm 2.25µm
MEASURING By Comparison
effective diameter)
INSTRUMENT, Method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using ULM and
Thread Ring Gauge
(BASIC Master Ring Gauge
106 (minor diameter 5 mm to 100 mm 1.4µm
MEASURING By Comparison
effective diameter)
INSTRUMENT, Method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Ultrasonic Thickness Using Gauge Block
(BASIC
107 Gauge(Thickness/He set("0" Grade) by 0 to 100 mm 66.7µm
MEASURING
ight) L.C.-0.1 mm Comparison Method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL- Using Gauge Block
DIMENSION Set/Long Gauge
Vernier Caliper
(BASIC Block Set, Surface
108 (Dial/Digital/Analog) 0 to 300 mm 22µm
MEASURING Plate, Slip Gauge
L.C.-0.01 mm
INSTRUMENT, Accessory set By
GAUGE ETC.) Comparison Method
MECHANICAL- Using Gauge Block
DIMENSION Set/Long Gauge
Vernier Caliper
(BASIC Block Set, Surface
109 (Dial/Digital/Analog) 0 to 1000 µm 20.7µm
MEASURING Plate, Slip Gauge
L.C.-0.02 mm
INSTRUMENT, Accessory set By
GAUGE ETC.) Comparison Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 21 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using digital
Hydraulic pressure
Hydraulic Pressure
gauge with
MECHANICAL- gauge/ Pressure
Hydraulic Pressure
PRESSURE Transmitter
110 comparator,and 0 to 700 bar 0.13% rdg
INDICATING /Pressure
Indicating device
DEVICES transducer/pressure
digital multimeter-as
switch. L.C.-0.01 bar
per DKD-R-6-1 by
comparison method
Pneumatic Pressure Using digital
gauge/ Pressure Pneumatic pressure
MECHANICAL-
Transmitter gauge with
PRESSURE
111 /Pressure Pneumatic pump, 0 to 7 bar 0.07% rdg
INDICATING
transducer/pressure digital multimeter as
DEVICES
switch. L.C.-0.001 per DKD-R-6-1 by
bar comparison method
Pneumatic Pressure Using digital
gauge/Pressure Pneumatic pressure
MECHANICAL-
Transmitter gauge with
PRESSURE
112 /Pressure Pneumatic pump, 7 bar to 35 bar 0.19% rdg
INDICATING
transducer/pressure digital multimeter as
DEVICES
switch. L.C.-0.001 per DKD-R-6-1 by
bar comparison method
MECHANICAL- Using Dead Weight
PRESSURE Pressure Gauge Tester. as per DKD
113 3.5 bar to 35 bar 0.21% rdg
INDICATING L.C.-0.0001 bar R-6-1 by comparison
DEVICES method
MECHANICAL- Using Dead Weight
PRESSURE Pressure Gauge Tester. as per DKD
114 35 bar to 700 bar 0.18% rdg
INDICATING L.C.-0.01 bar R-6-1 by comparison
DEVICES method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 22 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Digital
MECHANICAL- Vacuum Gauge with
PRESSURE Vacuum Gauge Hand Pump
115 -0.90 bar to 0 bar 0.3% rdg
INDICATING L.C.-0.0001 bar Comparator as per
DEVICES DKD R-6-2 by
comparison method
Using Torque sensor
Torque Wrench/ with indicator &
MECHANICAL-
Torque Screw Torque Wrench
TORQUE
116 Driver(Type-I Class Calibration System >100 Nm to 500 Nm 2.06%
GENERATING
B,C,D & E and Type based on IS
DEVICES
II Class A,B,D,E & G) 16906-2018 by
Comparison Method
Using Torque sensor
Torque Wrench/ with indicator &
MECHANICAL-
Torque Screw Torque Wrench
TORQUE >500 Nm to 1380
117 Driver(Type-I Class Calibration System 4.29%
GENERATING Nm
B,C,D & E and Type based on IS
DEVICES
II Class A,B,D,E & G) 16906-2018 by
Comparison Method
Using Digital
balance of 200 g
Glassware like
with readability 0.1
Pipettes, Burettes,
MECHANICAL- mg & distilled water
118 Measuring Cylinder, 1 ml to 100 ml 47µl
VOLUME By gravimetric
Density bottle,
method based on
Volumetric Flask
IS/ISO 4787 by
Comparison Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 23 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Digital
balance of 5000 g
Glassware like
with readability 10
Pipettes, Burettes,
MECHANICAL- mg & distilled water
119 Measuring Cylinder, 100 ml to 2000 ml 0.5ml
VOLUME By gravimetric
Density bottle,
method based on
Volumetric Flask
IS/ISO 4787 by
Comparison Method
Using Digital
Balance up to 80g /
200g readability
0.01 mg, distilled
MECHANICAL- water of known
120 Micropipette 100 µl to 1000 µl 3µl
VOLUME density By
gravimetric method
as per ISO/TR 20461
by Comparison
Method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
121 1g 0.052mg
WEIGHTS coarser Procedure based on
OIML R [Link]
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01.
122 1 mg 0.06mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 24 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
123 10 g 0.5mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.1 mg.
124 100 g 1mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
125 100 mg 0.09mg
WEIGHTS coarser Procedure based on
OIML R [Link]
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
126 2g 0.2mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01mg.
127 2 mg 0.06mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 25 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
128 20 g 0.42mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
129 20 mg 0.09mg
WEIGHTS coarser Procedure based on
OIML R 111-1. by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.1 mg.
130 200 g 0.21mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
131 200 mg 0.017mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01 mg.
132 5g 0.3mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 26 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01mg.
133 5 mg 0.06mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01mg.
134 50 g 0.20mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01mg.
135 500 mg 0.051mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using F1 Class
weights & balance of
MECHANICAL- Weight M2 Class and readability 10 mg.
136 1000 g 21.2mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
Comparison Method
Using F1 Class
weights & balance of
MECHANICAL- Weight M2 Class and readability 10 mg.
137 2000 g 13.6mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
Comparison Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 27 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using F1 Class
weights & balance of
MECHANICAL- Weight M2 Class and readability 10 mg.
138 500 g 24.1mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
Comparison Method
Using F1 Class
weights & balance of
MECHANICAL- Weight M2 Class and readability 10 mg.
139 5000 g 40.6mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
Comparison Method
Using E1 Class
weights & balance of
readability 0.01/0.1
MECHANICAL- Weight M1 Class and
140 mg. Procedure 10mg 0.07mg
WEIGHTS coarser
based on OIML R
111-1 by
Comparison Method
Using E1 Class
weights & balance of
MECHANICAL- Weight M1 Class and readability 0.01mg.
141 50 mg 0.042mg
WEIGHTS coarser Procedure based on
OIML R 111-1 by
comparison method
Using Digital Thermo
Humidity Sensor /
THERMAL- Hygrometer with
Transducer/Transmit
142 SPECIFIC HEAT Sensor, Humidity 40 % RH to 85 %RH 2.72%RH
ter with Indicator @
& HUMIDITY Chamber By
Temperature 25°C
Compression Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 28 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using master RTD

sensor Pt100
Liquid in Glass (accuracy class-DIN
THERMAL- Thermometer/ Dial 1/10) with Digital -20 °C
143 0.21 °C
TEMPERATURE Thermometer/ High accuracy to 50 °C
Digital Thermometer thermometer, Liquid
bath by comparison
method
Using master RTD
sensor Pt100
(accuracy class-DIN
Liquid in Glass 1/10) with Digital
THERMAL- Thermometer/ Dial High accuracy
144 50 °C to 250 °C 1.16°C
TEMPERATURE Thermometer/ thermometer, Liquid
Digital Thermometer bath(Range -20°C to
50 °C,
Resolution-0.1°C) by
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 29 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using master RTD

sensor Pt100
(accuracy class-DIN
1/10) with Digital
RTD sensor / High accuracy
Thermocouple with thermometer, Dry
or without Indicator, Bath (Range--35 deg
THERMAL-
145 Temperature C to 100 deg C) & -20 °C to 250 °C 0.56°C
TEMPERATURE
Transmitter/Transdu temperature
cer with or without calibrator (Range 50
Indicator °C – 650 °C), read
out unit Digital
thermometer and
Digital Multimeter by
comparison method
Using master R-Type
Thermocouple with
Digital high accuracy
Thermocouple with
thermometer, read
or without Indicator,
out unit Digital
THERMAL- Temperature 250 °C
146 thermometer and 1.88 °C
TEMPERATURE Transmitter/Transdu to 1200 °C
Digital Multi meter &
cer with or without
Dry Block Furnace (
Indicator
range up to 1200
°C) by comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 30 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Site Facility
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
1 Digital Multimeter by 1 mA to 100 mA 0.200 % to 0.176 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
2 Digital Multimeter by 100 µA to 1 mA 0.375 % to 0.20 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Current (50 Hz -
3 Digital Multimeter by 100 mA to 10 A 0.176 % to 0.223 %
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using High Voltage
Alternating AC High Voltage @
4 Probe with DMM By 1 kV to 30 kV 11.25 % to 3.07 %
Current (< 1 50Hz
Comparison Method
GHz)
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 31 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
5 Digital Multimeter by 1 V to 10 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
6 Digital Multimeter by 10 V to 100 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
7 Digital Multimeter by 100 mV to 1 V 0.08%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Using 6½ Digit
Alternating AC Voltage (50 Hz -
8 Digital Multimeter by 100 V to 750 V 0.084%
Current (< 1 1 kHz)
Direct Method
GHz)
(Measure)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
9 Alternating AC Current (50 Hz ) Function Calibrator 100 mA to 2 A 0.36 % to 0.41 %
Current (< 1 By Direct Method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 32 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 5 ½ digit
TECHNICAL-
Multi-Function
10 Alternating AC Current (50 Hz ) 2 A to 10 A 0.41 % to 0.33 %
Calibrator By Direct
Current (< 1
Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
11 Alternating AC Current (50 Hz ) Function Calibrator 200 µA to 100 mA 0.40 % to 0.36 %
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO- Using 5½ digit Multi-
TECHNICAL- Function Calibrator
AC High Current (50
12 Alternating & 100 turn Current 10 A to 900 A 2.01 % to 0.98 %
Hz )
Current (< 1 Coil By Direct
GHz) (Source) Method
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
13 Alternating Function Calibrator 100 mV to 100 V 1.91 % to 0.22 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
14 Alternating Function Calibrator 100 V to 1000 V 0.22 % to 0.20 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
AC Voltage (50 Hz to
15 Alternating Function Calibrator 5 mV to 100 mV 3 % to 1.91 %
60 Hz)
Current (< 1 By Direct Method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 33 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digit
16 DIRECT DC Current Digital Multimeter by 1 A to 10 A 0.100 % to 0.163 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
17 DIRECT DC Current Digital Multimeter by 1 mA to 100 mA 0.06%
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
18 DIRECT DC Current Digital Multimeter by 10 µA to 100 µA 0.30 % to 0.06 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
19 DIRECT DC Current Digital Multimeter by 100 µA to 1 mA 0.06%
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
20 DIRECT DC Current Digital Multimeter by 100 mA to 1 A 0.06 % to 0.10 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using High Voltage
21 DIRECT DC High Voltage Probe with DMM By 1 kV to 30 kV 11.78 % to 4.19 %
CURRENT Comparison Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 34 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digit
22 DIRECT DC Voltage Digital Multimeter by 1 V to 1000 V 0.005 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
23 DIRECT DC Voltage Digital Multimeter by 10 mV to 100 mV 0.44 % to 0.01 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
24 DIRECT DC Voltage Digital Multimeter by 100 mV to 1 V 0.01 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
1 Mega ohm to 10
25 DIRECT Resistance (2wire) Digital Multimeter by 0.015 % to 0.03 %
Mega ohm
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
10 Mega ohm to 100
26 DIRECT Resistance (2wire) Digital Multimeter by 0.03 % to 0.38 %
Mega ohm
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
27 DIRECT Resistance (4 wire) Digital Multimeter by 1 k ohm to 10 k ohm 0.011%
CURRENT Direct Method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 35 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digit
10 k ohm to 100 k
28 DIRECT Resistance (4 wire) Digital Multimeter by 0.011%
ohm
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digit
29 DIRECT Resistance (4 wire) Digital Multimeter by 100 ohm to 1 k ohm 0.1 % to 0.006 %
CURRENT Direct Method
(Measure)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
30 DIRECT DC Current Function Calibrator 0.2 mA to 100 mA 5.9 % to 0.15 %
CURRENT By Direct Method
(Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
31 DIRECT DC Current Function Calibrator 1 A to 10 A 0.15 % to 0.23 %
CURRENT By Direct Method
(Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
32 DIRECT DC Current Function Calibrator 100 mA to 1 A 0.14 % to 0.25 %
CURRENT By Direct Method
(Source)
ELECTRO- Using 5½ digit Multi-
TECHNICAL- Function Calibrator
33 DIRECT DC High Current & 100 turn Current 10 A to 900 A 2.67 % to 0.81 %
CURRENT Coil By Direct
(Source) Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 36 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 5½ digit Multi- 3.0 %
34 DIRECT DC Voltage Function Calibrator 0.5 mV to 100 mV
CURRENT By Direct Method to 1.2 %
(Source)
ELECTRO-
TECHNICAL- Using 5½ digit Multi-
35 DIRECT DC Voltage Function Calibrator 100 mV to 100 V 0.12%
CURRENT By Direct Method
(Source)
ELECTRO-
TECHNICAL- Using 6½ Digit
36 DIRECT DC Voltage Digital Multimeter by 100 V to 1000 V 0.13%
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
37 DIRECT Resistance Resistance Box By 1 ohm to 10 ohm 0.86 % to 0.15 %
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
10 k ohm to 10
38 DIRECT Resistance Resistance Box By 0.12 % to 0.13 %
Mega ohm
CURRENT Direct Method
(Source)
ELECTRO-
TECHNICAL- Using Decade
39 DIRECT Resistance Resistance Box By 10 ohm to 10 kohm 0.15 % to 0.12 %
CURRENT Direct Method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 37 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Decade
10 Mega ohm to
40 DIRECT Resistance Resistance Box By 0.13 % to 2.48 %
1000 Mega ohm
CURRENT Direct Method
(Source)
ELECTRO- B Type
TECHNICAL- Thermocouple Using Process
41 TEMPERATURE (Temperature Source By 600 °C to 1800 °C 1.83 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- E Type
TECHNICAL- Thermocouple Using Process
42 TEMPERATURE (Temperature Source By -200 °C to 1000 °C 0.70°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO-
J Type Thermocouple
TECHNICAL- Using Process
(Temperature
43 TEMPERATURE Source By -200 °C to 1200 °C 0.70°C
Indicator / controller
SIMULATION Simulation Method
/ recorder)
(Source)
ELECTRO- K Type
TECHNICAL- Thermocouple Using Process
44 TEMPERATURE (Temperature Source by -200 °C to 1370 °C 0.80 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- L Type
TECHNICAL- Thermocouple Using Process
45 TEMPERATURE (Temperature Source by -200 °C to 900 °C 0.81°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 38 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- N Type
TECHNICAL- Thermocouple Using Process
46 TEMPERATURE (Temperature Source by -200 °C to 1300 °C 1.29°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- R Type
TECHNICAL- Thermocouple Using Process
0
47 TEMPERATURE (Temperature Source by 1.83°C
to 1750 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO-
RTD PT 100
TECHNICAL- Using Process
(Temperature
48 TEMPERATURE Source by -200 °C to 800 °C 0.94 °C
Indicator / controller
SIMULATION Simulation Method
/ recorder)
(Source)
ELECTRO- S Type
TECHNICAL- Thermocouple Using Process
0
49 TEMPERATURE (Temperature Source by 1.83°C
to 1750 °C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
ELECTRO- U Type
TECHNICAL- Thermocouple Using Process
50 TEMPERATURE (Temperature Source by -200 °C to 600 °C 0.81°C
SIMULATION Indicator / controller Simulation Method
(Source) / recorder)
Using Digital
MECHANICAL- Digital Tachometer with
100 rpm to 5000
51 ACCELERATION Tachometer(Non- rpm source. As per 2.1% rdg
rpm
AND SPEED Contact Type) Sanas TR-45-01 by
Comparison Method:

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 39 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Digital
MECHANICAL- RPM Meter/
Tachometer as per 5000 rpm to 90000
52 ACCELERATION Centrifuge / (Non- 0.40% rdg
Sanas TR-45-01 by rpm
AND SPEED Contact Type)
Comparison Method
Using Digital
MECHANICAL- RPM Meter/
Tachometer as per
53 ACCELERATION Centrifuge / (Non- 10 rpm to 100 rpm 6.0% rdg
Sanas TR-45-01 by
AND SPEED Contact Type)
Comparison Method
Using Digital
MECHANICAL- Tachometer with
Tachometer
54 ACCELERATION rpm source. As per 10 rpm to 100 rpm 10% rdg
(Contact Type)
AND SPEED Sanas TR-45-01 by
Comparison Method
Using Digital
MECHANICAL- Tachometer with
Tachometer 100 rpm to 4000
55 ACCELERATION rpm source as per 2.2% rdg
(Contact Type) rpm
AND SPEED Sanas TR-45-01 by
Comparison Method
Using Sound Level
MECHANICAL- Sound Level Meter
56 calibrator by 114 dB 1.79dB
ACOUSTICS (Frequency- 1 kHz)
Comparison Method
Sound Level Using Sound Level
MECHANICAL-
57 Meter(Frequency- 1 calibrator by 94 dB 1.76dB
ACOUSTICS
kHz) Comparison Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 40 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using digital
Hydraulic pressure
Hydraulic Pressure
gauge with
MECHANICAL- gauge / Pressure
Hydraulic Pressure
PRESSURE Transmitter
58 comparator,and 0 to 700 bar 0.2% rdg
INDICATING /Pressure
Indicating device
DEVICES transducer/pressure
digital multimeter-as
switch. L.C.-0.01 bar
per DKD-R-6-1 by
comparison method
Using digital
Hydraulic pressure
Hydraulic Pressure
gauge with
MECHANICAL- gauge/ Pressure
Hydraulic Pressure
PRESSURE Transmitter
59 comparator,and 0 to 700 bar 0.13% rdg
INDICATING /Pressure
Indicating device
DEVICES transducer/pressure
digital multimeter-as
switch. L.C.-0.01 bar
per DKD-R-6-1 by
comparison method
Pneumatic Pressure Using digital
gauge/ Pressure Pneumatic pressure
MECHANICAL-
Transmitter gauge with
PRESSURE
60 /Pressure Pneumatic pump, 0 to 7 bar 0.07% rdg
INDICATING
transducer/pressure digital multimeter as
DEVICES
switch. L.C.-0.001 per DKD-R-6-1 by
bar comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 41 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Pneumatic Pressure Using digital

gauge/Pressure Pneumatic pressure
MECHANICAL-
Transmitter gauge with
PRESSURE
61 /Pressure Pneumatic pump, 7 bar to 35 bar 0.19% rdg
INDICATING
transducer/pressure digital multimeter as
DEVICES
switch. L.C.-0.001 per DKD-R-6-1 by
bar comparison method
Using Digital
MECHANICAL- Vacuum Gauge with
PRESSURE Vacuum Gauge Hand Pump
62 -0.90 bar to 0 bar 0.3% rdg
INDICATING L.C.-0.0001 bar Comparator as per
DEVICES DKD R-6-2 by
comparison method
MECHANICAL-
UTM, TENSION Uni-axial Static Using Proving ring
CREEP AND Testing Machine / as per IS 1828
63 1000 kN to 2000 kN 0.76%
TORSION UTM, CTM, (Part-1) by
TESTING (Compression Mode) Comparison Method
MACHINE
MECHANICAL-
Uni-axial Static
UTM, TENSION Using Proving ring
Testing Machine /
CREEP AND as per IS 1828
64 UTM, 100 kN to 1000 kN 0.8%
TORSION (Part-1) by
CTM,(Compression
TESTING Comparison Method
Mode)
MACHINE
MECHANICAL- Electronic Weighing Using M1 Class
WEIGHING Balance (Class IIII weights as per OIML
65 50 kg to 100 kg 43g
SCALE AND and coarser) R-76-1 by
BALANCE Readability: 10 g comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 42 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL- Electronic Weighing Using M1 Class

WEIGHING Balance (Class IIII weights as per OIML
66 100 g to 50 kg 7g
SCALE AND and coarser) R-76-1 by
BALANCE Readability: 5 g comparison method
Electronic Weighing
MECHANICAL- Using E1 Class
Balance (Class-I and
WEIGHING weights as per OIML
67 coarser of 1 mg to 200 g 0.25mg
SCALE AND R-76-1 by
readability 0.01 mg/
BALANCE comparison method
0.1 mg)
Using F1 Class
MECHANICAL- Electronic Weighing
Standard Weights
WEIGHING Balance (Class-II and
68 >200g to 6 kg as 200 g to 5000 g 0.29g
SCALE AND coarser of
per OIML R-76-1 by
BALANCE readability 0.01 g)
comparison method
Using digital thermo
THERMAL-
Indicator of Humidity hygrometer with
69 SPECIFIC HEAT 40 %RH to 85 %RH 3.05%RH
Chamber sensor by
& HUMIDITY
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 43 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using master RTD

sensor Pt100
(accuracy class-DIN
1/10) with Digital
RTD sensor / High accuracy
Thermocouple with thermometer, Dry
or without Indicator, Bath (Range--35 deg
THERMAL-
70 Temperature C to 100 deg C) & -20 °C to 250 °C 0.56°C
TEMPERATURE
Transmitter/Transdu temperature
cer with or without calibrator (Range 50
Indicator °C – 650 °C), read
out unit Digital
thermometer and
Digital Multimeter by
comparison method
Using master R-Type
Temperature
Thermocouple with
THERMAL- Indicator with sensor 250 °C
71 Digital thermometer 2.24 °C
TEMPERATURE of Muffle Furnance, to 1200 °C
by comparison
Oven
method
Using master RTD
Temperature
THERMAL- sensor Digital
72 Indicator with sensor -20 °C to 25 °C 0.42 °C
TEMPERATURE thermometer, by
of Liquid Bath
comparison method
Using master RTD
Temperature
THERMAL- sensor Digital
73 Indicator with sensor 25 °C to 250 °C 0.30°C
TEMPERATURE thermometer, by
of Liquid Bath, Oven
comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 SIBALI INSTRUMENT WORKS, JAGACHA MAHIARY ROAD & A. T. GHOSH ROAD
Laboratory Name :
JUNCTION, HOWRAH, WEST BENGAL, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2737 Page No 44 of 44
Validity 20/07/2022 to 19/07/2024 Last Amended on 09/11/2022

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
[Link] Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using master R-Type

Thermocouple with
Digital high accuracy
Thermocouple with
thermometer, read
or without Indicator,
out unit Digital
THERMAL- Temperature 250 °C
74 thermometer and 1.88 °C
TEMPERATURE Transmitter/Transdu to 1200 °C
Digital Multi meter &
cer with or without
Dry Block Furnace (
Indicator
range up to 1200
°C) by comparison
method
* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.

This is annexure to 'Certificate of Accreditation' and does not require any signature.