PHASE EQUILIBRIUM
PHASE RULE
INTRODUCTION
➢ “Phase rule” is an important tool used for the quantitative treartment of
systems in equilibrium.
➢ It enables us to predict the conditions that must be specified for a system to
exhibit equilibrium.
➢ Two or more different phases are present in equilibrium to form a
“heterogenous system”. Such system are studied by phase rule.
➢ J. Willard Gibbs enunciated the phase rule in 1876 on the basis of
Thermodynamic principles
➢ This rule predicts qualitatively the effect of temperature, pressure and
concentration on a heterogenous equilibrium.
Gibbs phase rule
“ In a heterogeneous system in equilibrium is not affected by gravity or
by electrical and magnetic forces, the number of degrees of freedom(F)
of the system is related to the number of component(C) and the number
of phases(P) existing at equilibrium”.
It is expressed by mathematically,
F=C –P+ 2
where,
F - number of degrees of freedom
C - number of components
P - number of phases
2 - additional variables of temperature and pressure
Phase
It is defined as “ Physically distinct, homogenous and mechanically
separable part of a system ”.
(i) A gaseous mixture constitutes a single phase since gases are completely
miscible.
example : Air
(ii) Two or more liquids which are miscible with one another constitute a
single phase as there is no bounding surfaces separating the different
liquids.
example : water and alcohol, chloroform and benzene constitute one
phase system.
(iii) A system consisting of a liquid in equilibrium with its vapour constitute a
two phase system
Component
It is defined as “Minimum number of independent variable
constituents which are required to express the composition of
each phase in the system”.
Degrees of Freedom
“It is defined as the minimum number of independent variables such as
temperature, pressure and concentration which should be specified in
order to define the system completely”.
Examples
(i)State of a pure gas can be specified by two variables P and T or P and V
third variable can be calculated.
Hence pure gas has degree of freedom two (F = 2)
(ii) H2O(l) Equilibrium withH2O(g) (F = 1) Monovariant
(ii) A gaseous mixture say N2 and O2 gases is completely defined when three
variables(T,P and C).
(F=3) Trivariant.
(i)The greater the number of components in a system, greater is
the degree of freedom for a given number of phases.
(ii) The greater the number of phases, the smaller is the number of
degrees of freedom.
(iii) The number of phases is maximum, the number of degrees
of freedom = Zero, for a given number of components.
For
One component system P = 3
Two component system P = 4
Three component system P = 5
Advantages
(i) It provides a simple method of classifying equilibrium states of
systems.
(ii) The phase rule confirms that the different systems having the
same number of degrees of freedom behave in same
manner.
(iii) It is applicable only to macroscopic systems and not concerned
with molecular structure.
(iv) It predicts the behaviour of the systems with changes in the
variables that govern the system in equilibrium.
(v) It predicts that, under a given conditions whether a number of
substances taken together would remain in equilibrium or it
involves in some interconversion or elimination.
(vi) It does not give the informations about the nature of the reactants or
products in the reactions
(vii) It finds extensive use in the study of many heterogeneous
systems.
(viii) It is extremely useful in the extraction of metals.
Limitations
(i) The phase rule is applicable to heterogeneous systems in
equilibrium, hence it is not applicable for the systems which are
slow to attain the equilibrium state.
(ii) It is applicable to a single equilibrium state. It never gives
information about the other possible equilibrium in the system.
(iii) Variables such as temperature, pressure and composition
are only taken into account in Gibbs phase rule, .
(iv) It does nottake in account the electric and magnetic
influences. For consideration of such variables, the factor 2 of
the Phase rule has to be adjusted accordingly.
(v) All the phases in the system must be present under the same
Temperature, Pressure and Gravitational force .
(vi) Solid or liquid phases are not finely divided, If it happens
deviation must occurs.
Phase diagrams
➢ “A phase diagram is the sum of the description of the behaviour of the
phases present in equilibrium”
➢ The number of phases that exist in equilibrium depends upon the conditions
of temperature and pressure or temperature and composition, pressure
being constant.
➢ These conditions are determined experimentally and the values of the
variables can be exposed graphically by using appropriates coordinates.
These diagrams are called phase diagram.
➢ It is very easy to describe the phase behaviour of a system by such
diagrams and to investigate the conditions in which various
phases will constitute the system .
Application of Gibbs Phase Rule
One Component System
From the mathematical expression of phase rule,
F=C–P+2
When C = 1, P = 1
F = 1-1+2
=2
All one component systems can be completely described graphically by
stating only two variables such as pressure
and temperature on appropriate axis.
Water System
➢It is a one component system.
➢Water exists in three possible phases viz. ice (solid) , water (liquid), and vapour
(gas). These three single phases may form four possible equilibria.
(i) Solid Liquid
(ii) Liquid Vapour
(iii) Solid Vapour
(iv) Solid Liquid Vapour
PHASE DIAGRAM OF WATER
The phase diagram consists of the following important
aspects
(i) Stable curves: three OB, OA and OC
(ii) Metastable curve: one OA'
(iii) Areas: three AOB, COB and AOC
(iv) Triple point: One O
Curve OA
(i)It is known as vapour pressure curve of water. The curve OA starts from
point O i.e., freezing point of water, 0.0075°C under 4.58 mm of Hg
pressure
and ends at A, the critical temperature (3740C at 218 atm.).
(ii) Above critical temperature on the vapour phase exists whatever may
be the value of pressure.
.(iii) The vapour pressure of water increases with increase in T
(iv) curve OA slants upwards and slopes away from the temperature axis.
From phase rule, F=C–P+2
= 1- 2 + 2 = 1
The water vapour system is univariant
Curve OB
(i) It is the sublimation curve. Along this curve, solid ice is in
equilibrium with its vapour.
(ii) This curve is not the prolongation of curve A but falls of more
steeply. Curve OB starts From the temperature 0.0075°C above
which solid water i.e., ice cannot exist.
(iii) The curve ends at B .It is present in absolute zero (- 273°C). At
this temperature, no vapour can exist and, hence only the
solid water(ice) is present.
(iv) The other points of the curve OB, ice is in equilibrium with
vapour. Hence, there are two phases. According to phase rule,
F=C–P+2
= 1 – 2 + 2 =1
hence, the system is univariant.
Curve OC
(i) It is the Melting point curve or Fusion curve of ice. Along
this curve two phases, ice and water are in equilibrium.
(ii)The inclination of OC line towards the pressure axis indicates
that the melting point of ice is slightly lowered by increase of
pressure.
(iii) Le Chatelier's principle states that “Increase in pressure
causes the water - ice equilibrium to shift in such a
direction that there is a decrease in volume”.
F = C – P + 2 =1-2+2 = 1 (univariant)
(pressure and melting point have fixed value)
Metastable Curve
Curve OA'
(i) It is called “metastable curve” shown in continuation of AO.
When water is cooled below its freezing point without separation
of ice.
(ii) The water is said to be “super cooled water”. The vapour pressure curve of
liquid water AO extends below O as shown by the dotted
curve OA'.
(iii) Along curve OA' liquid water coexists with vapour. The vapour
pressures are different than over the solid.
(iv) This equilibrium is called “metastable equilibrium”
as slight disturbance brings it to the stable region OB of the
phase diagram.
Areas
(i) The areas give the conditions of temperature and pressure under
which single phase of waer such as water solid(ice), liquid
water and water vapour can exist.
(ii) It is necessary to specify both temperature and pressure to
define a system within this area.
(iii)In this area , the curves BOC, AOC and AOB are exist as ice,
water (liquid) and water vapour respectively.
In these areas F=2. It is Bivariant
Triple point O
➢The point O at which the curves AO, BO and CO meet is called
the “Triple point”.
➢At this point all the three phases viz , ice, water and vapour co-
exist. Thus, P =3.
F = C –P + 2, =1-3+2 , F = 0
➢It indicates that there is only one set of variables P and T at which all
the three phases coexist.
➢ If any of the variables is changed, then the number of phases
decreases.
➢If the temperature is raised, the heat melts the soild ice.
➢There is no change in temperature or pressure of the system occurs till the
entire solid has completely converted into liquid.
➢If it happens the system becomes a two phase system (P = 2)
➢There is no change in temperature or pressure of the
system occurs till the entire solid has completely converted into liquid.
➢If it happens the system becomes a two phase system (P = 2)
➢By applying pressure to the system, the vapour starts condensing to
liquid or solid phase.
➢As long as the contents remains present in three phases, temperature and
pressure remains same.
➢The triple point O is a self defined point corresponding to 0.0075°C
temperature and 4.58 mm of Hg pressure
