Scribd
Upload
100 views7 pages

MAX7219 8x8 Matrix Display Module

This document provides instructions for assembling and using an 8x8 LED matrix kit. The kit includes a MAX7219 chip, resistors, capacitors, and headers to drive the LED matrix. It connects to an Arduino via 3 data lines and 2 power lines. The document describes connecting the hardware, programming it with example Arduino code to display letters and numbers, and adjusting the brightness in software. It is designed to be an easy beginner project for displaying basic patterns on an LED matrix.

Uploaded by

ALVIN PAJO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100 views7 pages

MAX7219 8x8 Matrix Display Module

This document provides instructions for assembling and using an 8x8 LED matrix kit. The kit includes a MAX7219 chip, resistors, capacitors, and headers to drive the LED matrix. It connects to an Arduino via 3 data lines and 2 power lines. The document describes connecting the hardware, programming it with example Arduino code to display letters and numbers, and adjusting the brightness in software. It is designed to be an easy beginner project for displaying basic patterns on an LED matrix.

Uploaded by

ALVIN PAJO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

20/10/2014 LED matrix kit - Elecrow

LED matrix kit


From Elecrow

Contents
1 Introduction
2 Specification of LED Matrix
3 Assembly Instruction
4 Usage
4.1 Hardware Installation
4.2 Software Programming
5 Resources

Introduction
This product is a serially driven 8x8 LED Matrix kit powered by MAX7219.

It only needs three data lines and two power lines.

The 8x8 LED Matrix is easy to use and compatible with Arduino, and its LED brightness adjustment can be
implemented in software.

8x8 LED Matrix kit has many applications in real life, such as various types of electronic display panels. If
the LED matrix is not driven by any peripherals, it’ll waste the interface of devices, and the LED brightness
will be impaired due to insufficient power, so that we cannot get ideal display effect.

The LED matrix can be driven in two ways: parallel or serial. We usually drive it in the serial manner in
order to save interface. The serial-driven LED matrix actually dynamically displays the LEDs, i.e., displays
the LEDs row-by-row or column-by-column. The persistence of vision for humans is about 0.1s, so as long
as we can serially display all 8 rows/columns within 0.1s, we’ll see a complete character or pattern.

[Link] 1/7
20/10/2014 LED matrix kit - Elecrow

This product comes in the form of a kit or module. The kit includes the following components:

MAX7219

Electrolytic cpaacitor：10uF/25V

Resistor：10K

Capacitance：0.1uF

Headers and receptacles.

After assembling, The Led matrix module will look as:

Specification of LED Matrix


[Link] 2/7
20/10/2014 LED matrix kit - Elecrow

Operating Voltage: DC 4.7V – 5.3V

Typical Voltage: 5V

Operating Current: 320mA

Max Operating Current: 2A

Operating Temperature: 0 ℃ – 50 ℃

Typical Temperature: 25 ℃

Assembly Instruction
This is a great beginner kit, easy to make even if you are have never soldered before. Please download this
step by step Assembly tutorials ([Link]
and then follow it to solder it.

Please pay attention that if it doesn't show as you wanted. it isn't that you soldered wrong. you need to
change the direction then assemble it.

Usage
Hardware Installation

Connection Wires

The schematics of the LED matrix is attached below.

Please follow the following instructions to connect hardwares.

1. The 8x8 LED Matrix must be common-grounded with the Arduino module;
2. Connect Arduino pin 8 to DIN on the LED Matrix;
3. Connect Arduino pin 9 to CS on the LED Matrix;
4. Connect Arduino pin 10 to CLK on the LED Matrix;
5. Use independent power supply for the 8x8 LED Matrix Shield, and the supply voltage is 5V/2A.

[Link] 3/7
20/10/2014 LED matrix kit - Elecrow

Schematics of the 8x8 LED Matrix

Testing Steps

[Link] Instructions

Connect Arduino pin8 to DIN on 8x8 LED Matrix


Connect Arduino pin9 to CS of 8x8 LED Matrix
Connect Arduino pin10 to CLK of 8x8 LED Matrix
Connect Arduino 5V to VCC of 8x8 LED Matrix
Connect Arduino GND to GND of 8x8 LED Matrix

Attention：8*8LED Matrix must be common-grounded with Arduino module.

[Link] 4/7
20/10/2014 LED matrix kit - Elecrow

[Link] the corresponding interfaces are properly connected.

[Link]'d better powering up the Arduino/Crowduino with AC adapter.

[Link]：The LED matrix should circularly display the digits 0 to 9 on LED screen first, then the
characters A to Z, as shown in the above figure.

Software Programming

You can download the Max7219 drive library LedControl,zip ([Link]


title=File:[Link]) or program the Arduino/Crowduino with the following Example code.

Example code

unsigned char i;
unsigned char j;
/*Port Definitions*/
int Max7219_pinCLK = 10;
int Max7219_pinCS = 9;
int Max7219_pinDIN = 8;

unsigned char disp1[38][8]={


{0x3C,0x42,0x42,0x42,0x42,0x42,0x42,0x3C},//0
{0x10,0x18,0x14,0x10,0x10,0x10,0x10,0x10},//1
{0x7E,0x2,0x2,0x7E,0x40,0x40,0x40,0x7E},//2
{0x3E,0x2,0x2,0x3E,0x2,0x2,0x3E,0x0},//3
{0x8,0x18,0x28,0x48,0xFE,0x8,0x8,0x8},//4
{0x3C,0x20,0x20,0x3C,0x4,0x4,0x3C,0x0},//5
{0x3C,0x20,0x20,0x3C,0x24,0x24,0x3C,0x0},//6
{0x3E,0x22,0x4,0x8,0x8,0x8,0x8,0x8},//7
{0x0,0x3E,0x22,0x22,0x3E,0x22,0x22,0x3E},//8
{0x3E,0x22,0x22,0x3E,0x2,0x2,0x2,0x3E},//9
{0x8,0x14,0x22,0x3E,0x22,0x22,0x22,0x22},//A
{0x3C,0x22,0x22,0x3E,0x22,0x22,0x3C,0x0},//B
{0x3C,0x40,0x40,0x40,0x40,0x40,0x3C,0x0},//C
{0x7C,0x42,0x42,0x42,0x42,0x42,0x7C,0x0},//D
{0x7C,0x40,0x40,0x7C,0x40,0x40,0x40,0x7C},//E
{0x7C,0x40,0x40,0x7C,0x40,0x40,0x40,0x40},//F
{0x3C,0x40,0x40,0x40,0x40,0x44,0x44,0x3C},//G

[Link] 5/7
20/10/2014 LED matrix kit - Elecrow
{0x44,0x44,0x44,0x7C,0x44,0x44,0x44,0x44},//H
{0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x7C},//I
{0x3C,0x8,0x8,0x8,0x8,0x8,0x48,0x30},//J
{0x0,0x24,0x28,0x30,0x20,0x30,0x28,0x24},//K
{0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x7C},//L
{0x81,0xC3,0xA5,0x99,0x81,0x81,0x81,0x81},//M
{0x0,0x42,0x62,0x52,0x4A,0x46,0x42,0x0},//N
{0x3C,0x42,0x42,0x42,0x42,0x42,0x42,0x3C},//O
{0x3C,0x22,0x22,0x22,0x3C,0x20,0x20,0x20},//P
{0x1C,0x22,0x22,0x22,0x22,0x26,0x22,0x1D},//Q
{0x3C,0x22,0x22,0x22,0x3C,0x24,0x22,0x21},//R
{0x0,0x1E,0x20,0x20,0x3E,0x2,0x2,0x3C},//S
{0x0,0x3E,0x8,0x8,0x8,0x8,0x8,0x8},//T
{0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1C},//U
{0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18},//V
{0x0,0x49,0x49,0x49,0x49,0x2A,0x1C,0x0},//W
{0x0,0x41,0x22,0x14,0x8,0x14,0x22,0x41},//X
{0x41,0x22,0x14,0x8,0x8,0x8,0x8,0x8},//Y
{0x0,0x7F,0x2,0x4,0x8,0x10,0x20,0x7F},//Z
};

void Write_Max7219_byte(unsigned char DATA)


{
unsigned char i;
digitalWrite(Max7219_pinCS,LOW);
for(i=8;i>=1;i--)
{
digitalWrite(Max7219_pinCLK,LOW);
digitalWrite(Max7219_pinDIN,DATA&0x80);// Extracting a bit data
DATA = DATA<<1;
digitalWrite(Max7219_pinCLK,HIGH);
}
}

void Write_Max7219(unsigned char address,unsigned char dat)


{
digitalWrite(Max7219_pinCS,LOW);
Write_Max7219_byte(address); //address，code of LED
Write_Max7219_byte(dat); //data，figure on LED
digitalWrite(Max7219_pinCS,HIGH);
}

void Init_MAX7219(void)
{
Write_Max7219(0x09, 0x00); //decoding ：BCD
Write_Max7219(0x0a, 0x03); //brightness
Write_Max7219(0x0b, 0x07); //scanlimit；8 LEDs
Write_Max7219(0x0c, 0x01); //power-down mode：0，normal mode：1
Write_Max7219(0x0f, 0x00); //test display：1；EOT，display：0
}

void setup()
{

pinMode(Max7219_pinCLK,OUTPUT);
pinMode(Max7219_pinCS,OUTPUT);
pinMode(Max7219_pinDIN,OUTPUT);
delay(50);
Init_MAX7219();
}

void loop()
{
for(j=0;j<38;j++)
{
for(i=1;i<9;i++)
Write_Max7219(i,disp1[j][i-1]);
delay(500);
}
}

[Link] 6/7
20/10/2014 LED matrix kit - Elecrow

Retrieved from "[Link]

This page was last modified on 28 October 2013, at 03:05.


This page has been accessed 841 times.

[Link] 7/7

You might also like