Solutions for industrial automation
and monitoring
Technical specifications
2 3 4 5
1 Linux Inside
Based on open-source software
with Debian GNU/Linux OS 6
ARM Cortex A7 core @ 800 MHz
512 MBytes of RAM
1
4 GBytes of eMMC Flash storage
11 RS-485 & CAN 7 8 9 10 11
Up to 4 RS-485 ports
CAN port
Support of Modbus RTU, meters
and sensors, arbitrary protocols 9 GSM/3G modem
Primary or alternate
3 2 x Ethernet communications channel
Sending SMS
Two Ethernet 10/100 ports for connection
to IP networks and the Internet GPRS (up to 80 kbit/s)
TCP/IP, UDP, HTTP(S) or 3G (up to 5 Mbit/s)
Modbus TCP, SNMP, MQTT, KNX IP
8 Wi-Fi + BT
10 Input and Output
802.11n (up to 150Mbps)
6 multifunctional I/O ports that
Access point mode is supported
can function as
Bluetooth 4.0 and Bluetooth Low Energy
0-30V analog inputs
Discrete inputs and outputs
1-Wire sensor inputs 7 433 MHz Radio
Versatile radio transceiver for communication
2 Power supply with third-party proprietary wireless devices
12 to 48V DC
Connector for reduntant power supply 4 2 x USB 2.0 Ports
Power over Ethernet (Passive PoE) 3G/4G modems, printers,
flash drives support
Embedded rechargeable battery (up to 4 hours)
available as an option Disconnectable port power supply
Supported hardware
Modbus RTU (RS-485)
Wiren Board sensors, I/O and lighting control modules
Wide variety of industrial I/O modules
and other equipment manufactured by:
S+S, Advantech and so on
KNX (EIB)
Supports both KNX TP (KNX bus) and KNX/IP
A wide variety of KNX devices for automation
of residential and commercial facilities
The controller functions as a KNX IP Gateway
M-Bus Meters
M-Bus bus master interface
Electricity, heat and gas meters
Wireless M-Bus (work in progress)
Z-Wave
Certified software package with Z-Wave Plus support
Over 1000 compatible wireless devices
Load switching Wired sensors
Low-voltage loads: Intermediate relays, LEDs, Sensors with a voltage (up to 30V)
fans, signal lamps, remote control taps etc. or current (4-20mA) analog output
230VAC loads: Contactors, heated floors, Sensors with a relay or «open collector» output:
ventilation, roller blinds etc. Smoke, leak, movement detectors etc.
Reed switches and opening sensors
1-Wire digital temperature sensors
Thermistors, Pt100 and Pt1000 sensors
(requires an extension module)
User Interfaces
Web Rule Additional
Interface Engine Functions
Easy network connectivity, Event-based scenarios Email and SMS notifications
including access from
Timers and Schedules Data logging
mobile devices
View and manage all Knowledge base with
connected devices ready-made solutions
Rooms and dashboards Usage of virtual devices
Functions library
Iridium Mobile Apple HomeKit
Platform designed to control Smart home Full control from your iPhone
and IoT devices
Zabbix, Grafana, various SCADAs and other monitoring software
WB-MR relay modules
WB-MR are relay modules (contactors) controlled via Modbus RTU. They are used
for switching various load types: lighting, ventilation, heated floors, equipment
power supply units etc.
The series includes modules with a large selection of number of channels and load
capacities. We are particularly proud of our high inrush current relay modules
designed for capacitive loads such as LED lighting, incandescent lamps etc. They
can handle inrush current for up to 800A eliminating the need for a separate
contactor: .
The majority of modules in the series are equipped with discrete inputs that can be
used for direct control of the relay channels or as general purpose inputs.
Connection of wires
with cross-section up to 4 sq. mm. DIN-rail mount
3M or 6M wide
Protection of relays
from induced voltage surges
Three-tier
Reliable Hongfa relays quality control
Control of coil current for
increased energy efficiency Output status indication
Wide range of Inputs may be used to
power voltages: 12-24 V control relay channels
Reliable control for extreme
applications
Control of digital TV
retransmission stations
Located all over Kazakhstan, TV
retransmission stations are full of
complex TV equipment as well as
uninterruptible power supplies and
sensors.
A special version of Wiren Board
PAC controls the state of every
device and is capable of turning it
on and off.
Thanks to its own battery, Wiren Board stays operational even after the UPS goes
off. The controller's GPRS link is totally independent from the main communication
channel. All these measures ensure the controller's ability to send a signal in any
emergency situation.
Oil well automation (Azerbaijan)
In oil fields, Wiren Board PACs are used to
collect data, to control variable-frequency
drives and to manage the oil well's auxiliary
equipment.
The controllers have specialized K-Logic
software on board.
The control stations are polled using the
Modbus RTU protocol.
Oil well equipment control station.
Binagadi field, Azerbaijan
Building and home automation
Building management
system for bank branches
Wiren Board PACs, I/O modules and
sensors are used to control lighting,
HVAC, humidity systems in the
building, as well as security, fire and
flood safety.
?
Wiren Board sensors and the bank’s own software together provide a comfortable
environment for employees and customers, including temperature and humidity,
illuminance, carbon dioxide (CO2) concentration. Collecting data from electricity,
water and heat meters helps to identify energy-inefficient branches and decrease
their consumption after engineering systems optimization.
Home automation for
300 apartments in
Skolkovo residential
Wiren Board PACs and I/O modules
allow to control lighting (including
scenarios-based) and HVAC systems
in every apartment. The PAC also
controls the water leak and security
system detectors.
Apple iPads with Iridium Mobile UI
are used as HMI.
