Instruction Manual February 2003

multiranger
100/200
Safety Guidelines
Warning notices must be observed to ensure personal safety as well as that of others, and to
protect the product and the connected equipment. These warning notices are accompanied
by a clarification of the level of caution to be observed.

Qualified Personnel

This device/system may only be set up and operated in conjunction with this manual.
Qualified personnel are only authorized to install and operate this equipment in accordance
with established safety practices and standards.

Warning: This product can only function properly and safely if it is correctly transported,
stored, installed, set up, operated, and maintained.

Note: Always use product in accordance with specifications.

Copyright Siemens Milltronics Process Disclaimer of Liability

Instruments Inc. 2003. All Rights Reserved

This document is available in bound version and in While we have verified the contents of
electronic version. We encourage users to this manual for agreement with the
purchase authorized bound manuals, or to view instrumentation described, variations
electronic versions as designed and authored by remain possible. Thus we cannot
Siemens Milltronics Process Instruments Inc. guarantee full agreement. The
Siemens Milltronics Process Instruments Inc. will contents of this manual are regularly
not be responsible for the contents of partial or reviewed and corrections are included
whole reproductions of either bound or electronic in subsequent editions. We welcome
versions. all suggestions for improvement.

Technical data subject to change.

MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments Inc.

Contact SMPI Technical Publications at the following address:

Technical Publications
Siemens Milltronics Process Instruments Inc.
1954 Technology Drive, P.O. Box 4225
Peterborough, Ontario, Canada, K9J 7B1
Email: techpubs@[Link]

For the library of SMPI instruction manuals, visit our Web site: [Link]

© Siemens Milltronics Process Instruments Inc. 2003

Table of Contents

Table of Contents
The MultiRanger 100 and 200 ...............................................................................................................1

mmmmm
MultiRanger 100 ............................................................................................................................1
MultiRanger 200 ............................................................................................................................1
The Manual ...............................................................................................................................................1
Manual Symbols ............................................................................................................................2
Configuration Examples ...............................................................................................................2
Specifications ...............................................................................................................................................3
Installation ......................................................................................................................................................7
Mounting ...................................................................................................................................................7
Mounting Locations ......................................................................................................................7
Mounting Instructions ..................................................................................................................8
MultiRanger Board .......................................................................................................................9
Installing the Battery ..................................................................................................................10
Installing SmartLinx Card ..........................................................................................................10
Optional Equipment .....................................................................................................................10
Wiring ..............................................................................................................................................................11
Terminal Board .......................................................................................................................................12
Cables .......................................................................................................................................................12
Transducers ............................................................................................................................................13
Relays .......................................................................................................................................................13
Temperature Sensor .............................................................................................................................14
mA Input [MR 200 only] .......................................................................................................................14
mA Output ...............................................................................................................................................14
Level System Synchronization ...........................................................................................................15
Power .......................................................................................................................................................15
Digital Communications .......................................................................................................................16
RS-232 Serial Connection ..........................................................................................................16
RS-485 Serial Connection ..........................................................................................................16
Operating the MultiRanger ..................................................................................................................17
RUN Mode ..............................................................................................................................................17
Readings in RUN Mode .......................................................................................................................18
Status Parameters ................................................................................................................................19
Controlling the Display .........................................................................................................................20
Auxiliary Reading ........................................................................................................................20
Multiple Readings [MR 200 only] ............................................................................................21
PROGRAM Mode ..................................................................................................................................22
Starting PROGRAM Mode ..................................................................................................................22
Hand Programmer .......................................................................................................................22
Programmer Keys ........................................................................................................................23
Dolphin Plus ............................................................................................................................................24
Dolphin Plus Toolbar Buttons ...................................................................................................25
Activating the MultiRanger .................................................................................................................26

i
 Changing Parameters .................................................................................................................26
Security ....................................................................................................................................................27
Using Units or Percent (%) ..................................................................................................................27
Table of Contents

Parameters Types ..................................................................................................................................27

Parameter Reset ....................................................................................................................................28
mmmmm

Display Readout .....................................................................................................................................28

Changing Parameters(Dolphin Plus) .......................................................................................29
Parameter Indexing ....................................................................................................................30
Primary and Secondary Indexes .......................................................................................................31
Starting Measurement ........................................................................................................................32
Single Point Models ....................................................................................................................32
Dual Point Models .......................................................................................................................33
Measurement Conditions ..........................................................................................................34
Relays ...............................................................................................................................................................35
General Introduction ...................................................................................................................35
Relay Function ..............................................................................................................................35
Relay States ..................................................................................................................................37
Relay Related Parameters ........................................................................................................37
Relay Activation ...........................................................................................................................38
Relay Failsafe ...............................................................................................................................39
Preset Applications ...............................................................................................................................40
Backup Level Override ...........................................................................................................................41
Backup Level Override Parameters ..................................................................................................41
Discrete Inputs ...........................................................................................................................................42
Wiring the Discrete Inputs ..................................................................................................................42
Programming the Discrete Input Logic ............................................................................................42
mA I/O ..............................................................................................................................................................43
mA Input [MR 200] ................................................................................................................................43
mA Output ...............................................................................................................................................43
Volume [MR 200] ........................................................................................................................................45
Readings ..................................................................................................................................................45
Tank Shape and Dimensions ..............................................................................................................45
Characterization Chart [MR 200] .......................................................................................................46
Example Chart ..............................................................................................................................46
MultiRanger 200 only .................................................................................................................47
Alarms .............................................................................................................................................................48
Level ..........................................................................................................................................................48
Setting Simple Level Alarms .....................................................................................................49
Rate [MR 200] .........................................................................................................................................49
In Bounds/ Out of Bounds Range [MR 200] ....................................................................................50
Cable Fault ..............................................................................................................................................50
Temperature [MR 200] ..........................................................................................................................50
Loss of Echo (LOE) .................................................................................................................................51

ii
Pump Control ...............................................................................................................................................52
Setting a Pump Down Group ..............................................................................................................52

Table of Contents
Setting a Pump Up (Reservoir) Group ..............................................................................................53
Other Pump Control Algorithms .........................................................................................................55
Set Relays to ALTERNATE DUTY BACKUP [MR 200] ..........................................................55

mmmmm
Set Relays to FIXED DUTY ASSIST ........................................................................................55
Set Relays to FIXED DUTY BACKUP [MR 200] .....................................................................56
Set Relays to ALTERNATE DUTY SERVICE [MR 200] ..........................................................56
Set Relays to FIRST IN FIRST OUT (FIFO) ASSIST [MR 200] ............................................57
Optional Pump Controls .......................................................................................................................57
Starting Pumps by Rate of Level Change [MR 200] ............................................................57
Rotating Pumps by Service Ratio [MR 200] ..........................................................................58
Totalizing Pumped Volume [MR 200] ......................................................................................59
Setting Independent Failsafe Controls ...................................................................................59
Setting a Pump to Run On [MR 200] .......................................................................................60
Setting the Pump Start Delays [MR 200] ...............................................................................60
Reducing Wall Cling [MR 200] ..................................................................................................60
Grouping Pumps [MR 200] ........................................................................................................61
Setting a Flush Valve [MR 200] ................................................................................................61
Relay Controlled by Communications ....................................................................................62
Tracking Pump Usage ..........................................................................................................................62
Rake (Screen) Control [MR 200] ........................................................................................................63
Setting a Rake Control .........................................................................................................................63
Setting the Common Parameters ............................................................................................64
Set Relay 1 (Operate Rake) .......................................................................................................64
Set Relays 2 to 4 (Level Alarms) ..............................................................................................64
External Totalizers and Flow Samplers [MR 200] ....................................................................65
Relay Contacts .......................................................................................................................................65
Totalizer ....................................................................................................................................................65
Flow Sampler ..........................................................................................................................................66
Based on Volume and Time ......................................................................................................66
Open Channel Monitoring (OCM)
[MR 200] ..........................................................................................................................................................67
Common Parameters ............................................................................................................................67
Setting Zero Head .......................................................................................................................68
Setting Totalized Volume .....................................................................................................................69
Applications Supported by MultiRanger 200 .................................................................................69
PMDs with Exponential Flow to Head Function ............................................................................73
Applicable Weir Profiles ............................................................................................................73
Non-Applicable Weir Profiles ..................................................................................................74
Parshall Flume ..............................................................................................................................74
Leopold Lagco Flume ..................................................................................................................75
Cut Throat Flume .........................................................................................................................76
Universal Calculation Support ...........................................................................................................77
Typical Flow Characterization ..................................................................................................77
Example Flumes ...........................................................................................................................78

iii
 Example Weirs .............................................................................................................................78
Testing the Configuration ......................................................................................................................79
Table of Contents

Simulation ...............................................................................................................................................79
Simulating a Single Measurement ...................................................................................................79
mmmmm

Simulating a Level Cycle ......................................................................................................................79

Checking Volume Characterization [MR 200] .................................................................................80
Checking OCM Flow Characterization [MR 200] ...........................................................................80
I/O Checkout ...........................................................................................................................................81
Application Test .....................................................................................................................................81
MultiRanger Communications ...........................................................................................................83
MultiRanger Communication Systems ............................................................................................83
Optional SmartLinx®Cards ................................................................................................................83
Communication Systems .....................................................................................................................84
Communication Ports ...........................................................................................................................84
Modbus ..........................................................................................................................................84
SmartLinx ................................................................................................................................................85
Dolphin Plus ............................................................................................................................................85
Communications Installation .............................................................................................................86
Wiring Guidelines ..................................................................................................................................86
Ports 1 and 2 .................................................................................................................................86
Ports 1 and 2: RS-232 RJ-11 Jack and RS-485 Locations ..................................................86
Port 1: RS-232 RJ-11 Jack ..........................................................................................................87
Port 2: RS-485 ..............................................................................................................................87
Configuring Communication Ports (Parameters) ...........................................................................88
Modbus Register Map ............................................................................................................................91
Word Order (R40,062) ..........................................................................................................................92
Map ID (R40,063) ....................................................................................................................................92
Product ID (R40,064) ..............................................................................................................................93
Point Data (R41,010 – R41,031) ............................................................................................................93
Input/Output (R41,070 – R41,143) .........................................................................................................93
Discrete Inputs (R41,070) ..........................................................................................................94
Relay Outputs (R41,080) ..............................................................................................................94
mA Input (R41,090) [MR 200] .....................................................................................................94
mA Output (R41,110-41,111) ........................................................................................................94
Pump Control (R41,400 – R41,474) ............................................................................................94
Pump ON Setpoint (R41,420 – R41,425) ...................................................................................94
Pump OFF Setpoint (R41,430 – R41,435) .................................................................................95
Pumped Volume (R41,440 – R41,443) [MR 200] .....................................................................95
Pump Hours (R41,450 – R41,461) .............................................................................................95
Pump Starts (R41,470 – R41,475) ..............................................................................................95
Parameter Access (R43,998 – R46,999) ..................................................................................96
Parameter Indexing ....................................................................................................................96
Reading Parameters ...................................................................................................................97
Writing Parameters .....................................................................................................................98
Format Words (R46,000 to R46,999) ..................................................................................................99
Global Index Method (P782 = 0) ...............................................................................................99

iv
 Parameter-Specific Index Method (P782 = 1) .......................................................................99
Format Registers .........................................................................................................................99

Table of Contents
Data Types ...................................................................................................................................................101
Numeric Values ...................................................................................................................................101

mmmmm
Bit Values ...............................................................................................................................................101
Unsigned Double Precision Integer (UINT32) .............................................................................101
Split Values .......................................................................................................................................... 102
Text Messages .................................................................................................................................... 103
Relay Function Codes (P111 Only) ................................................................................................. 104
Error Handling .......................................................................................................................................... 106
Modbus Responses ........................................................................................................................... 106
Error Handling ..................................................................................................................................... 106
Communication Troubleshooting .................................................................................................. 108
Generally .............................................................................................................................................. 108
Specifically ........................................................................................................................................... 108
Communication Appendix A: Single Parameter Access (SPA) .................................... 109
Reading Parameters .......................................................................................................................... 109
Writing Parameters .............................................................................................................................110
Format Register ...................................................................................................................................110
Error Codes ...........................................................................................................................................111
Parameter Reference ............................................................................................................................113
MultiRanger 100 and MultiRanger 200 ................................................................................113
Helpful Hints ...............................................................................................................................113
Quick Start (P001 to P007) .................................................................................................................115
Volume (P050 to P055) [MR 200] ......................................................................................................119
Display and Reading (P060 to P062) ..............................................................................................123
Backup Level Override .......................................................................................................................125
Failsafe (P070 to P072) ......................................................................................................................127
Relays (P100 to P119) .........................................................................................................................128
Pump Setpoint Modifiers (P121 and P122) [MR 200] ..................................................................135
Independent Relay Failsafe (P129) .................................................................................................136
Advanced Pump Control Modifiers (P130 to P137) [MR 200] ...................................................137
Flush Systems (P170 to P173) [MR 200] .........................................................................................140
mA Output (P200 to P219) ..................................................................................................................142
Independent mA Setpoints (P210 and P211) .................................................................................144
mA Output Limits (P212 and P213) ...................................................................................................145
mA Output Trim (P214 to P215) .........................................................................................................146
mA Output Failsafe (P219) [MR 200] ...............................................................................................146
mA Input (P250 to P260) [MR 200] ...................................................................................................147
Discrete Input Functions (P270 to P275) .......................................................................................149
Standard Data Logging (P300 to P321) .........................................................................................150
Record Temperatures (P300 to P303) ............................................................................................150
Record Readings (P304 and P305) .................................................................................................152
Pump Records (P310 to P312) ...........................................................................................................152
Flow Records (P320 and P321) [MR 200] .......................................................................................153

v
 LCD Totalizer (P322 and P323) [MR 200] ........................................................................................154
Profile Records (P330 to P337) ........................................................................................................155
Auto Record ON and OFF Setpoints (P334 to P337) ....................................................................158
Table of Contents

Installation Records (P340 to P342) ...............................................................................................160

Open Channel Monitoring (P600 to P621) [MR 200] ...................................................................161
mmmmm

Pumped Volume Totalizer (P622) [MR 200] ...................................................................................170

Totalizer (P630 to P645) [MR 200] ....................................................................................................171
Range Calibration (P650 to P654) ....................................................................................................174
Temperature Compensation (P660 to P664) ..................................................................................177
Rate (P700 to P708) ............................................................................................................................179
Measurement Verification (P710 to P713) ....................................................................................183
Transducer Scanning (P726 to P729) .............................................................................................186
Display (P730 to P739) .......................................................................................................................187
SmartLinx Reserved (750 to 769) ....................................................................................................190
Communications (P770 to P782) .....................................................................................................190
SmartLinx Hardware Testing ............................................................................................................193
Echo Processing (P800 to P807) ......................................................................................................195
Advanced Echo Processing (P810 to P825) ..................................................................................198
Profile Pointer (P817 to P825) .......................................................................................................... 200
Advanced TVT Adjustment (P830 to P835) .................................................................................. 205
Advanced Shot Adjustment (P840 to P852) ................................................................................. 208
Test (P900 to P913) ..............................................................................................................................211
Measurement (P920 to P927) ...........................................................................................................215
Master Reset (P999) ..........................................................................................................................218
General Appendix A: Index Types ..................................................................................................219
Index types ............................................................................................................................................219
General Appendix B–Technical Reference ............................................................................. 220
Transmit Pulse ..................................................................................................................................... 220
Echo Processing ................................................................................................................................. 220
Distance Calculation ......................................................................................................................... 221
Sound Velocity .................................................................................................................................... 221
Scanning ............................................................................................................................................... 222
Volume Calculation [MR 200] .......................................................................................................... 222
Universal, Curved [MR 200] ................................................................................................... 223
Flow Calculation ................................................................................................................................. 223
Universal, Linear [MR 200] ..................................................................................................... 224
Universal, Curved [MR 200] ................................................................................................... 224
Maximum Process Speed ................................................................................................................ 225
General Appendix C: Troubleshooting ........................................................................................ 226
Common Problems Chart ................................................................................................................. 226
Noise Problems ................................................................................................................................... 227
Determine the Noise Source ................................................................................................. 228
Non-Transducer Noise Sources ........................................................................................... 228
Common Wiring Problems ..................................................................................................... 229
Reducing Electrical Noise ...................................................................................................... 229
Reducing Acoustical Noise .................................................................................................... 229
Measurement Difficulties ................................................................................................................. 230

vi
 Flashing LOE Display ............................................................................................................... 230
Fixed Reading ...................................................................................................................................... 231
Obstructions in the Sound Beam ......................................................................................... 231

Table of Contents
Nozzle Mountings .................................................................................................................... 232
Set the MultiRanger to Ignore the Bad Echo .................................................................... 232

mmmmm
Wrong Reading ................................................................................................................................... 233
Types of Wrong Readings ...................................................................................................... 233
Liquid Splashing ........................................................................................................................ 233
Adjust the Echo Algorithm ..................................................................................................... 233
Transducer Ringing ............................................................................................................................ 233
General Appendix D: Pump Control Reference ..................................................................... 235
Pump Control Options ....................................................................................................................... 235
Pump Groups ............................................................................................................................. 235
Pump by Rate [MR 200] .......................................................................................................... 235
Pump Control Algorithms ................................................................................................................. 236
Fixed Duty Assist (P111 = 50) ................................................................................................. 236
Fixed Duty Backup (P111 = 51) [MR 200] ............................................................................ 237
Alternate Duty Assist (P111 = 52) ........................................................................................ 237
Alternate Duty Backup (P111 = 53) [MR 200] ..................................................................... 238
Service Ratio Duty Assist (P111 = 54) [MR 200] ................................................................ 239
Service Ratio Duty Backup (P111 = 55) [MR 200] ............................................................. 240
First In First Out (FIFO) (P111 = 56) [MR 200] ...................................................................... 240
Pump by Rate (P121) [MR 200] .............................................................................................. 240
Other Pump Controls [MR 200] ....................................................................................................... 240
General Appendix E: Updating Software .................................................................................. 242
Updating Software ............................................................................................................................. 242
General Appendix F: Upgrading ..................................................................................................... 243
Mounting a MultiRanger 100/200 ......................................................................................... 243
Connecting the Transducer ................................................................................................... 243
MultiRanger Plus to MultiRanger 100/200 Parameters .................................................. 245
General Appendix G: Conduit Entry for Class 1, Div 2 Applications ........................... 246
Notes ............................................................................................................................................................. 248

vii
 mmmmm

Table of Contents Notes

viii
The MultiRanger 100 and 200

MultiRanger
The MultiRanger is available in two models, MultiRanger 100 and MultiRanger 200, and is

mmmmm
designed for a variety of applications:
• water and wastewater
• storage tanks, for measuring liquids, slurries, and solids
• hoppers, ore bunkers, flotation cells

MultiRanger 100
The MultiRanger 100 is a single or dual-point level, three or six relay measurement
device. It is equipped with digital communications and offers the latest in echo
processing technology and diagnostic features.

MultiRanger 200
The MultiRanger 200 is a single or dual-point, three or six relay device that offers both
level and volume measurement. It has Open Channel Monitoring capabilities, a larger
number of advanced pump control algorithms, and is equipped with digital
communications. It offers the latest in echo processing technology and diagnostic
features.

The Manual
The manual provides instruction for both MultiRanger 100 and MultiRanger 200 models.
For your convenience, the manual uses MultiRanger 100 features as its standard content.
Additional MultiRanger 200 features are clearly marked.
The manual is designed to help you get the most out of your MultiRanger, and it provides
information on the following:

• How to program the unit • Outline diagrams

• Example applications • Wiring diagrams
• Principles of operation • Installation requirements
• Parameter values • MODBUS register mapping
• Parameter uses • Modem configuration

If you have any questions, comments, or suggestions about the manual contents, please
email us at techpubs@[Link].

For the complete library of Siemens Milltronics manuals, go to

[Link].

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 1

 Manual Symbols
Please note their use carefully.
MultiRanger

Alternating Current
mmmmm

Direct Current

Earth (ground) Terminal

Protective Conductor Terminal

Caution (refer to instructions)

Infra-red communication port on front of instrument

RJ-11 communications port

No co-axial cable connections

Configuration Examples
The configuration examples used in this manual illustrate the versatility of the
MultiRanger. Because there is often a range of ways to approach an application, other
configurations may also apply.
In all examples, substitute your own application details. If the examples do not apply to
your application, check the applicable parameter reference for the available options.

Should you require more information, please contact your Siemens Milltronics
representative. For a complete list of Siemens Milltronics representatives, go to
[Link].

Page 2 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Specifications
Power
AC version
• 100-230 Vac ± 15%, 50 / 60 Hz, 36 VA (17W)1
• fuse: F3: 2 AG, Slow Blow, 0.375A, 250V

DC version
• 12-30 Vdc, 20W1

Specifications
• fuse: F3: 2 AG, Slow Blow, 2A, 250V

mmmmm
Transmitter fuse
• F1: Belling Lee, L754, 4000A HRC, ceramic type, 100mA, 250V

Temperature Sensor fuse

• F2: Belling Lee, L754, 4000A HRC, ceramic type, 50mA, 250V

Mounting
Location
• indoor / outdoor

Altitude
• 2000m max.

Ambient temperature
• -20 to 50°C (-5 to 122°F)

Relative humidity
• suitable for outdoors (Type / Nema 4x, IP65 Enclosure)

Installation category
• II

Pollution degree
• 4

Range
• 0.3m (1 ft) to 15m (50 ft), dependent on transducer

1.
Power consumption is listed at maximum.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 3

 Accuracy
• 0.25% of maximum range or 6mm (0.24”), whichever is greater

Resolution
• 0.1% of program range1 or 2mm (0.08”), whichever is greater

Memory
• 1MB static RAM with battery backup
• 512kB flash EPROM
Specifications

Programming
mmmmm

Primary
• hand held programmer

Secondary
• PC running Dolphin Plus software

Display
• back lit LCD

Temperature Compensation
• Range: -50 to 150°C (-58 to 302°F)

Source
• integral transducer sensor
• TS-3 temperature sensor
• programmable fixed temperature

Temperature Error
Sensor
• 0.09% of range

Fixed
• 0.17% per °C deviation from programmed value

1.
Program range is defined as the empty distance from the face of the transducer
(P006) plus any range extension (P801).

Page 4 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Outputs
Transducer drive
• 315V peak

mA Analog
• 0-20 mA
• 4-20 mA
• 750 ohm maximum
• Resolution of 0.1%
• Isolated

Specifications
Relays1

mmmmm
• Three:
• 2 control
• 1 alarm control
• Six:
• 4 control
• 2 alarm control
• All relays rated 5A at 250Vac, non-inductive

Control Relays
• 2 or 4 Form A, NO relays (numbers 1,2,4,5)

Alarm Relay
• 1 or 2 Form C, NO, or NC relay (numbers 3,6)

Communication
• RS-232 running Modbus RTU and ASCII via RJ-11 connector
• RS-485 running Modbus RTU and ASCII via terminal blocks

Optional
• SmartLinx® compatible

Inputs
mA (analog) (1) [MR 200 only]
• 0-20 or 4-20 mA, from alternate device, scalable

1.
All relays are certified only for use with equipment that fails in a state at or
under the rated maximums of the relays.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 5

 Discrete (2)
• 10-50Vdc switching level
• logical 0 = < 0.5 Vdc
• logical 1 = 10 to 50 Vdc
• 3mA maximum draw

Enclosure
• 240mm (9.5") x 1.75mm (6.9"). Width dimension includes hinges.
• Type 4X / NEMA 4X / IP 651
• Polycarbonate

Weight
Specifications

• 1.37 kg (3.02 lb)

mmmmm

Approvals
• See product nameplate

Compatible Transducers
• EchoMax series and STH series

Transducers
Base
• single point (44 kHz)
• second transducer can only be used for average or differential [MR 200 only]

Option
• dual point (44 kHz)

Cable
• Do not use coaxial cable for transducer (see General Appendix F: Upgrading on
page 243 for more information)
• 2-3 copper conductors, twisted with shield, drain wire, 300Vrms, 0.5mm2 (22-18AWG),
nominal capacitance between adjacent conductors @ 1kHz = 19 pF/ft., nominal
capacitance between conductor and shield @ 1kHz = 33 pF/ft (Belden 8760 is
acceptable)
• 365m maximum

Note: The MultiRanger is to be used only in the manner outlined in this instruction
manual or protection provided by the equipment may be impaired.

1.
For watertight applications, use only approved, suitable size hubs in the
enclosure’s conduit holes.

Page 6 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Installation

Notes:
• Installation must only be performed by qualified personnel, and in accordance
with local governing regulations.
• This product is susceptible to electrostatic shock. Follow proper grounding
procedures.

All field wiring must have insulation suitable for at least 250 V.

Hazardous voltage present on transducer terminals during operation.

DC terminals shall be supplied from an SELV source in accordance with IEC

1010-1 Annex H.

• The non-metallic enclosure does not provide grounding between conduit

connections. Use grounding type bushings and jumpers.

Installation
Mounting

mmmmm
Mounting Locations
Recommended
• Ambient temperature is always within -20 to 50°C (-5 to 122°F)
• MultiRanger display window is at shoulder level, unless most interaction is through
a SCADA system
• Easy access for hand programmer is provided
• Cable length requirements are minimal
• Mounting surface is free from vibration
• A place for a laptop computer is provided for on-site Dolphin Plus configuration

Avoid
• Exposure to direct sunlight. (Provide a sun shield to avoid direct sunlight.)
• Proximity to high voltage/current runs, contacts, SCR or variable frequency motor
speed controllers

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 7

 Mounting Instructions
Mount the unit where there is sufficient room to swing lid open and have clear access.

Note: When routing cable through a conduit, please follow the Cable Routing
instructions on page 9 before mounting the MultiRanger.

Enclosure Dimensions

14.9mm 160.3mm 91mm

(0.58") (6.325") (3.58")
15.2mm 130mm 4.3mm Dia.
(0.6") (5.125") (0.17") 6.6mm
Four Mounting (0.26")
Holes

Enclosure
Screws (6)
240mm
(9.45")
227mm
(8.93")
Installation
mmmmm

Mounting the Enclosure

1. Remove the lid screws and open the lid to reveal the mounting screw holes.
2. Mark and drill four holes in the mounting surface
Mounting Screw Holes
for the four screws (customer supplied).
3. Fasten with a long screwdriver.

Please note: Mounting Screw Holes

• Recommended mounting: directly to wall or to

electrical cabinet back panel
• Recommended mounting screws: #6
• If alternate mounting surface is used, it MUST be
able to support four times the weight of the unit.

Page 8 MultiRanger– INSTRUCTION MANUAL 7ML19981FB02

 Cable routed through a conduit:
1. Remove the four mounting screws holding the
motherboard to the enclosure.
2. Be careful not to damage the electronics with static
electricity. Remove the motherboard from the enclosure
by pulling the board straight out.
3. Drill the required cable entry holes. Make sure conduit
holes do not interfere with the lower areas on the
terminal block, circuit board, or SmartLinx card.
4. Attach the conduit to the enclosure using only approved
suitable size hubs for watertight application.
5. Reinstall the motherboard with the mounting screws. Suitable location for conduit entrances

Note: For conduit locations and assembly for hazardous mounting in

Class 1 Div 2 applications, please see Drawing 23650314 in General
Appendix G: Conduit Entry for Class 1, Div 2 Applications on page 246.
Cable exposed and entering through the cable glands:
1. Unscrew the glands and attach them loosely to the enclosure.
2. Thread the cables through the glands. Ensure the power cable is kept separated
from the signal cables.
3. Wire the cables to the terminal blocks.
4. Tighten the glands to form a good seal.

Note: Where more holes are required than are supplied in the enclosure, follow

Installation
the Cable routed through a conduit steps.

mmmmm
MultiRanger Board

Battery
RS-232 RJ-11
Connector

TB1
Power Supply
TB2
L2/N L1
2

SYNC
TB3
Female Connector
for SmartLinx Card
1

mA INPUT

SHIELD

RELAY 1

4 - 20 mA
1
SmartLinx Card
OUTPUTS
RELAY 2
2

Terminals
RELAY 3
TS-3

SHIELD
1
RELAY 4
DISCRETE 2
INPUTS
RELAY 5

RELAY 6 RS485
COM

A
RS-485
B Connections

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 9

 Installing the Battery
The battery (Rayovac BR2032) has a ten-year life expectancy. Please note the life
expectance may be reduced by ambient temperature. If the unit loses external and
battery power, a capacitor will power the RAM for about ten minutes.

Disconnect power before replacing the battery.

Installation Steps
1. Open the enclosure lid.
2. Slide the battery into the holder. Be sure to
align the + and – terminals correctly.
3. Close and secure enclosure lid. Battery
+

Installing SmartLinx Card

SmartLinx cards are generally pre-installed. If unit does not have a SmartLinx card, follow
these steps to install one. For reference, see board illustration on page 9.
Installation

1. Align card with the two mounting posts and then press-fit with the female
mmmmm

connector.
2. Use the screws supplied with the card to attach it to the mounting posts.
3. Wire in the SmartLinx card according to SmartLinx Manual.

Optional Equipment
To communicate with equipment requiring RS-485 capability, Siemens Milltronics offers
the RS-485 External Modem Kit. For more information, go to
[Link].

Page 10 MultiRanger– INSTRUCTION MANUAL 7ML19981FB02

Wiring
Please note:
• Verify that all system components are installed in accordance with instructions.
• Connect all cable shields to the MultiRanger Shield Terminals. Avoid differential
ground potentials by not connecting cable shields to ground (earth) anywhere.
• Keep exposed conductors on shielded cables as short as possible to reduce noise
on the line caused by stray transmissions and noise pickup.

Milltronics
MultiRanger Transducer(s)

Milltronics TS-3
Temperature Sensor

Laptop running
Dolphin Plus

Customer Alarm,
Pump, or Control
Device

Customer Device,
digital output

Customer Device,
Wiring

analog output
mmmmm

Customer Network or
Modem

SmartLinx Card

Display, PLC, Chart

recorder, or other
Control Device

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 11

 Terminal Board
The terminal board on the MultiRanger allows all inputs and outputs to be connected
simultaneously.

Note: Recommended torque on terminal clamping screws.

• 0.56 - 0.79 Nm
• 5 - 7 [Link]
Please do not overtighten the screws.

TB1

TB2
L2/N L1
TB1
2
TB3
SYNC
1
12-30 V
mA INPUT

DC Version
SHIELD

RELAY 1
1
4 - 20 mA
OUTPUTS
RELAY 2
2

RELAY 3
TS-3

SHIELD
1
RELAY 4
DISCRETE 2
INPUTS
RELAY 5

COM

RELAY 6 RS485 A

Cables
Wiring
mmmmm

The MultiRanger transceiver requires a shielded two-wire connection to the transducer.

Connection Cable Type
mA input and mA output 2-3 copper conductors, twisted, with shield1, drain wire,
sync, Temperature sensor,
300V 0.5-0.75 mm2 (22 - 18 AWG)Maximum length: 365m
discrete input, dc input
Transducer
Do not use a coaxial transducer cable extension with the
MultiRanger. Electrical noise interference affects
performance.
Relay output Relay to be copper conductors per local requirements to
ac input meet 250V 5A contact rating.
1.
Preferred shielding is braided screen.

Page 12 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Transducers
Warning: Hazardous voltage present on transducer terminals during
operation.
Run the transducer cable in a grounded metal conduit, separate from other
wiring (except TS-3 temperature sensor wiring, if applicable).
Notes:
• Do not use coaxial cable because of electrical noise interference
• Do not connect the shield and white transducer wires together; wire to separate
terminals
• Disregard older transducer manuals that recommend these practices

white
TRANSDUCER TWO
black

white
TRANSDUCER ONE
black

A 0.1 µF (100V or greater) capacitor is included with the MultiRanger for retrofitting old
MultiRanger Plus installations. Please see MultiRanger 100/200 Installation (for
retrofitting MultiRanger Plus Installations) on page 244.

Relays
Relay contacts are shown in the de-energized position. All relays are handled identically
and can be configured as positive or negative logic using P118.

Relay Ratings Power Failure

• four Form A, NO Relays 1, 2, 4, and 5 are
relays(1,2,4,5) RELAY 1 normally open and will fail
• two Form C, NO or in the normal state.
Wiring
mmmmm

NC relays (3,6) RELAY 2

• 5A at 250Vac, non- Relays 3 and 6 can be
inductive wired either normally open
RELAY 3 or normally closed, and
will fail in their de-
energized states.

RELAY 4

RELAY 5

RELAY 6

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 13

 Temperature Sensor
Accurate temperature readings are critical to accurate level measurements because the
speed of sound changes, depending on air temperature, and all Milltronics Echomax and
ST-H transducers have an internal temperature sensor.

If the following conditions apply, a separate TS-3 temperature sensor will ensure
optimum accuracy:

• the transducer is exposed to direct sunlight (or other radiant heat source)
• the transducer face and monitored surface temperature differs
• faster response to temperature changes is required

Note
Use a T-S3 Temperature
TEMPERATURE SENSOR
Sensor only. Leave
terminals open (unused) if
TS-3 is not deployed.

mA Input [MR 200 only]

For more information, consult the Transducer (P004) and mA Input Parameters (P250,
P251, and P252) in the parameter reference section.
Wiring

mA Output
mmmmm

For more information, consult the mA output parameters (P200 to P219) in the parameter
reference section.

Page 14 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Level System Synchronization
Note: The MultiRanger 100/200 CANNOT be synchronized with the MultiRanger Plus
or the HydroRanger.

When using multiple ultrasonic level monitors, be sure to run the transducer cables in
separate grounded metal conduits.

When separate conduits are not possible, synchronize the level monitors so that no unit
transmits while another is waiting for echo reception.

Other Milltronics
Tranceiver MultiRanger

Synchronizing with another MultiRanger 100/200, or other Milltronics

instruments(DPL+, SPL, XPL+, Hydro+, EnviroRanger, MiniRanger):
• Mount the level monitors together in one cabinet
• Use a common power (mains) supply and ground (earth) for all units
• Interconnect the SYNC terminals of all level monitors
• Contact Siemens Milltronics or your local distributor. Go to
[Link].

Power
Important!
Before applying power to the MultiRanger for the first time, ensure any connected
alarm/control equipment is disabled until satisfactory system operation and
performance is verified.
Wiring

Notes for AC power connections mmmmm

• The equipment must be protected by a 15 A fuse, or circuit breaker in the

building installation.
• A circuit breaker or switch in the building installation, marked as the disconnect
switch, must be in close proximity to the equipment and within easy reach of the
operator.

Note: Make sure unit is

connected to a Ground
reliable ground.

GND L1
L2/N

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 15

 Digital Communications
Wiring the MultiRanger for communications allows it to be integrated into a full SCADA
system or an industrial LAN.

The MultiRanger can also be directly connected to a computer running Dolphin Plus.

RS-232 Serial Connection

RS-232 RJ-11
TB1 Connector
TB2
L2/N L1
2
TB3
SYNC
1

mA INPUT

SHIELD

RELAY 1
1
4 - 20 mA
OUTPUTS
RELAY 2
2

RELAY 3
TS-3

SHIELD
1
RELAY 4

RELAY 5
DISCRETE
INPUTS
2
RS-485
RELAY 6 RS485
COM

A
Connection
B
(see below)

RS-485 Serial Connection

Wiring
mmmmm

Discrete Inputs
Discrete inputs have a positive and negative terminal. Requires an external power supply.

Discrete Input (post.) 1

Discrete Input (pos.) 2

Common (neg.) for Discrete Input

Page 16 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Operating the MultiRanger
The MultiRanger has two modes of operation: RUN and PROGRAM.

RUN Mode
In RUN mode, the MultiRanger detects material level and provides control functions. The
MultiRanger automatically starts in RUN mode when power is applied.
System status is shown on the unit’s LCD, or on a remote communications terminal.

Display
1 2 3 4 5

?
8
1 2 3 4 5 6

14 13 12 11 10 9

Indicator Functions
RUN Mode PROGRAM Mode
1 index type (see below) index type (see next table)
2 index index
3 primary reading parameter value
4 units units
5 hi and hi hi alarm designation auxiliary function
6 level display n/a
7 filling display scroll access tag
8 emptying display scroll access tag
9 lo and lo lo alarm designation n/a
10 relay # programmed relay # programmed
11 relay # activated relay # activated
12 auxiliary reading parameter number
13 normal operation: n/a
Operation

14 failsafe operation: n/a

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 17

 Icons indicating index type (Item 1) edited in PROGRAM mode:
Icon Index Type
measurement point or transducer

relay
secondary index
mA input or output

Readings in RUN Mode

Change the displayed values with the keys on the hand programmer. All readings are
shown in the Auxiliary field, except for the totalizer and P920.
Key Function P#
Toggle Readings between percent and units: P920
• Level: 0 – 100%
• Space or Distance:1 100% – 0
+ Accumulated pump running hours2 for numbered pump. P310

+ Hold number key for five seconds to display the number of P311
accumulated pump starts2 for numbered pump.

Eight-digit totalizer, uses index and reading areas, press P322

[MR 200 only]
again to toggle, P737 sets default. P323
Used for OCM and Pumped Volume. P920
Head measurement P926
[MR200 only]
Instantaneous flow based on head (OCM) P925
[MR 200 only]
mA Output value P203
Temperature P664
Rate of level change P707
Failsafe Time Left (in %). When the Reading is updated,
this value (Auxiliary Reading) resets to 100 and begins to
decrease until the next valid measurement is made. If the
Failsafe Time Left reaches 0, LOE flashes in the display.
Hold for four seconds to show echo confidence P805
Display the value of the entered parameter which is global
+ ###
P or indexed by transducer
P
Auxiliary reading displays parameter specified in P731 P731
Distance P923
Operation
mmmmm

1.
Distances less than 0.3m (12") from the transducer face cannot be measured
reliably. Therefore, a 0% reading is not possible during Distance operation.
2.
If the associated relay is programmed for pump control.

Page 18 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Status Parameters
Status parameters give the operating status of the MultiRanger. You can access
parameters with the hand programmer (see page 26) or with Dolphin Plus (see page 22).
Remote SCADA system access is also possible.

Parameter Values
P203 mA Output Value 0 to 22 – Current mA output
P254 Scaled mA Input Value 0 to 9999 – Current mA input after scaling
[MR 200 only]
P275 Scaled Discrete Input Value Shows current value of discrete input,
values vary by DI function
P322 LCD Total Low The last four digits of the totalizer
[MR 200 only]
P323 LCD Total High The first four digits of the totalizer
[MR 200 only]
P341 Run Time The number of days the MultiRanger has
been operating
P342 Start Ups The number of times power has been
cycled
P664 Temperature Current temperature measured by
transducer
P707 Rate Value Current rate of material level change
P708 Volume Rate Display Current rate of material volume change
[MR 200 only]
P729 Scan Time Seconds since last level scan
P806 Echo Strength Strength of primary echo
P920 Reading Measurement Current primary reading
P921 Material Measurement Current level from P007–Span
P922 Space Measurement Empty space above the material level
P924 Volume Measurement Current volume value, if programmed
[MR 200 only]
P925 Flow Measurement (OCM) Current flow value, if OCM programmed
[MR 200 only]
P926 Head Measurement (OCM) Current level, if OCM programmed
[MR 200 only]
P927 Distance Measurement Distance from transducer face to material
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 19

 Controlling the Display
RUN mode provides numerous parameters and variables that you can track on the
display (see Display on page 17).
The LCD displays EEEE if a value is too long.

Adjusting the primary reading for four-digit LCD readout:

Parameter Action
P060 Decimal Position Sets maximum number of decimals
P061 Convert Reading Scales the reading to fit
P062 Offset Reading Shifts the reading up or down by a fixed amount

Example
To reference the displayed level to sea level, enter the distance in Units (P005), between
Empty (P006) and sea level. (Enter a negative value if Empty is below sea level.)

P006

P007

P062
Sea Level
Reservoir

P062 is the distance between sea level and Empty.

Auxiliary Reading
The Auxiliary Reading area of the LCD displays parameter values while leaving the
primary reading on screen.

Note: The parameters shown in the auxiliary reading field are indexed as follows:
• global
• by transducer
• by level point
Operation
mmmmm

Page 20 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Setting the Default Auxiliary Reading
To maintain a constant variable display in the auxiliary reading area, set the default.
Example:
To leave the level reading on the screen and view the echo confidence in the auxiliary
reading field, set the following parameter:

Parameter Index Value Description

P730 G 805 Auxiliary field defaults to P805

Setting a Specific Auxiliary Reading

To display a second auxiliary reading, press P in RUN mode.

Example: To set P to display current temperature, go to P731:

Parameter Index Value Description

P731 G 912 Shows P912–Transducer Temperature

Multiple Readings [MR 200 only]

During differential or average operation (P001 = 4 /5), the display scrolls sequentially
through Point Numbers 1, 2, and 3. Point 3 is the difference between (or average of) Points
1 and 2.

Changing Number Scrolling Speed

Parameter Index Value Description

P732 G 5 Hold each value for 5 seconds

See Parameter Indexing on page 31. All the instructions in the following procedures apply
to the hand programmer and assume that the MultiRanger is activated.
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 21

 PROGRAM Mode
The MultiRanger is programmed by setting its parameters to match your specific
application. Most parameters are indexed, allowing you to set the parameter to specific
conditions and to more than one input or output. When the MultiRanger is in PROGRAM
mode, you can change these parameter values and set operating conditions.
Please refer to the Parameter Reference section on page 113 for a full listing and
explanatios of parameter values.
The MultiRanger’s primary programming is by the hand programmer. Other access is
available through Dolphin Plus software (purchased separately).

Notes
• To activate PROGRAM from RUN mode, press PROGRAM and then DISPLAY
• The display briefly reads ---- while the measurement reading is verified. Reading
level and other data is displayed and programmed relays are operated.
• Placing a programmed unit that is in normal operation into PROGRAM mode de-
energizes all control relay outputs. Be sure to bypass the MultiRanger while
programming it.

Starting PROGRAM Mode

Hand Programmer
The hand programmer gives you direct access to
the MultiRanger.
Aim the hand programmer and press PROGRAM
key.

Notes:
• The battery in the programmer is not
replacable
• The hand programmer is ordered separately
from Siemens Milltronics
Infrared
Port
For your convenience, the
programmer has a magnetic mounting
strip on the back. Keep programmer
nearby for easy access.
Point the programmer at the IR port
above the display and press the keys.
Operation

Unless otherwise noted, each valid

mmmmm

key press should produce a change in

the LCD. Verify when programming the
unit.

Page 22 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Programmer Keys

Keys Programming Mode Run Mode

1 8-digit Totalizer (toggle)
[MR 200 only]
2 Pump Running Time

3 Head
[MR 200 only]
4 Flow based on Head
[MR 200]
5 mA Output

6 Temperature

7 Rate of Change

8 Failsafe Time Left

9 N/A

0 N/A

Decimal Point (TVT left) Parameter Value

Negative Value (TVT right) Material Level (P731)

P

Fire Transducer Distance

Run Mode Program Mode (Key 1)

Units or % Units or % (Program Mode)

(Key 2)
Next Display Field Pause Display Toggle

Increase Value Next Index

Decrease Value Previous Index

Enter Value

Clear to Preset
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 23

 Dolphin Plus
Use Dolphin Plus software to configure, monitor, tune, and diagnose the MultiRanger
from a PC or directly in the field with a laptop.
Dolphin Plus is easy to install and easy to use. Just load the software from the CD onto a
desktop PC or Laptop and then set up or modify complete parameter configurations in a
Windows®environment.
After configuration, you can edit parameters, upload and download parameter sets to
and from disk, and use parameter sets saved from other instruments. You can also work
with echo profiles for fine tuning without the need for special instruments. Built-in Quick
Start features and Help files guide you through the entire process.

Note: Dolphin Plus is ordered separately from Siemens Milltronics.

Operation
mmmmm

Page 24 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Dolphin Plus Toolbar Buttons
The toolbar buttons provide quick access to Dolphin Plus features.
Button Action
communicate with instrument–toggle online versus offline

monitor communications

send parameter set to instrument

save parameter set to file

open the quick start wizard

open the tabbed parameters window

find a parameter in the tabbed parameters window

toggle PROGRAM mode and RUN mode

open the reporting windows

load an echo profile from a file

save the current echo profile to a file

open the vertical echo profile and tank mimic window

open the horizontal echo profile window

take a measurement with the current transducer

open the reading values (distance measurement) window

print current echo profile

open the Echo Info Editor window

Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 25

 Activating the MultiRanger
All the instructions in the following procedures apply to the hand programmer and
assume that the MultiRanger is activated.
1. Power the MultiRanger.
2. Point the programmer at the unit and press PROGRAM .
3. Press DISPLAY .

Note: Power up display

• Single Point Model
• preset to display distance from the face of the transducer to the material
• transducer selection is preset for the XPS-10
• empty distance is preset to 5m
• Dual Point Model
• starts in an OFF state and does not take level measurements
• to set up measurement, the quick start parameters must be configured
• See Quick Start parameters on page 115

Changing Parameters

Note: If Parameter Value alteration is not permitted, access the Lock parameter
(P000) and enter the security code, (see Security below).

1. Starting in RUN mode, press PROGRAM and then press DISPLAY to put the
unit into PROGRAM mode.
2. Press DISPLAY to select the Parameter Number field.
3. Enter the Parameter Number (e.g. 110). After the third digit is entered, the parameter
value is shown.
4. Enter the new value, and press ENTER . The MultiRanger interprets the value,
either accepting or replacing it with a valid value.

Helpful Hints
• For parameters P001 to P009, press a single digit (1–9) and then press DISPLAY
to show that parameter.
• The ? icon indicates that the MultiRanger has accepted the value but that it conflicts
with other values entered. Double-check your programming.
• By default, the SCROLL arrows show only the Quick Start parameters and
any that have been changed.
• P733 sets all parameters to be scroll-accessed.
Operation
mmmmm

Page 26 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Security
The Lock parameter P000 secures the MultiRanger against parameter changes. The unit
can still be put into PROGRAM mode when locked, and parameter values can be viewed,
but no parameter values can be changed.
When P000 is set to 1954, programming is enabled. To disable programming, enter
another value.
P000 (1954) is a fixed value password. Therefore, you should use other means to secure
the MultiRanger if security is a concern.

Simulation
P000 Lock also controls how simulations affect control relays. By default, control relays
are unaffected by simulation levels. But if P000 is set to –1, they react to the simulated
level. See Parameters P925–P927 on page 217 for running a simulation.

Using Units or Percent (%)

Many parameters can be viewed either in measurement units (P005) or as a percentage.
View the parameter and then press MODE to toggle between units and percentage.
The LCD shows the selected measurement type, either units (m, ft) or percentage (%).

MR 200 only:
Percentage is also available when showing flow and volume with 100%, based on the
parameter that defines the maximum.
Measurement Maximum
Volume P051
Flow P604

Parameters Types
View Only Parameters
Parameter values indicating status only. They cannot be altered.

Global Values
Parameter values common to all inputs and outputs on the MultiRanger.
When a global parameter is accessed, the index display automatically disappears. When
a non-global parameter is accessed, the index display reappears showing the last index
number.
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 27

 Default Values
Parameter default values are indicated with an * in the parameter tables.
P000 Lock
Primary Index Global
1954 * OFF: programming permitted
Value -1 Simulation Controls (relays energize based on
simulated level)
other ON: Lock activated and programming not permitted
The asterix identifies 1954 as the default value.

Parameter Reset
Returning a parameter to factory default.
1. Display the appropriate parameter number.
2. Display the appropriate index value (if required).
3. Press CLEAR .
4. Press ENTER .

Master Reset (P999)

Returns all parameters to original values.
Use Conditions:
• before initial system installation
• following a software upgrade
If complete reprogramming is required, use Dolphin Plus to store and retrieve parameters.
When the dual point option is enabled, P999 is indexed by transducer. Use index 00 to
reset the entire MultiRanger.

Display Readout
The following readouts are shown when the MultiRanger cannot display a number.

Display Definition
Parameter has not been set
All values not same when viewing index 0

Value too large for four-digit display

Operation
mmmmm

Page 28 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Changing Parameters(Dolphin Plus)
The other method for changing parameter values is with Dolphin Plus software. It lets you
access the MultiRanger from a PC or on site with a laptop and change MultiRanger
parameters.
Most examples in this manual use the icons from the hand programmer but nearly all
functions are also available through Dolphin Plus.

Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 29

 Parameter Indexing
Parameters are indexed when they apply to more than one input or output. The index
value defines the input/output for that parameter. Indexed parameters contain a value for
each index, even if that index is not used.

MultiRanger Display
The index number and the index values are displayed above the parameter indicator on
the LCD.
Index Number Index Value

1 2 3 4 5 6

Notes
• Transducers are always indexed when the dual point option is enabled.
• An indexed transducer is commonly referred to as a Point (short for ’Measurement
Point’). Point Number refers to indexed transducers.
• To set all indexed values for a parameter to the same value, use index 0.
• MR 200 only: Transducer parameters are indexed only if Operation (P001) is set to
Difference (value=4) or Average (value=5) on a single point MultiRanger.

Accessing a Parameter Index

1. Press DISPLAY once to clear current parameter field.

2. Enter the new parameter number.
3. Press DISPLAY twice.
4. Press the number of the required index. Or press ARROW keys to scroll
through the available values.
Operation

Note: For optimum performance, set values accurately for indexed parameters.
mmmmm

Ensure that the correct index value is being changed for each parameter value.

Page 30 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Primary and Secondary Indexes
Primary Index: relates to direct input or output and can refer to relays, communications
ports, and other parameters. In parameters that allow secondary indexes, the primary
index is often referred to as a point.
Secondary Index: relates to previously indexed parameters where the parameter
requires a second index, permitting multiple values on an indexed input or output.

Primary Index
Example Setting: P111[3] = 52

P111

1 2 3 4 5 6

52

• P111 sets the Relay Control Function

• P111(3) = 52 sets Relay #3 to a value of 52.

Secondary Index
Parameters with a secondary index permit multiple values for a primary index (point). For
example, a volume calculation based on vessel characterization breakpoints requires a
distinct set of breakpoints for each measured point.
Thus the primary index refers to the measurement point, and each secondary index refers
to a characterization breakpoint value.

Accessing a Secondary Index

1. Press MODE and then press DISPLAY to activate secondary index. The
icon appears under the index field.
2. Enter the secondary index, and then enter the values to set the secondary index.
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 31

 Example [MR 200 only]
P054 provides up to 32 breakpoint levels used with P055 (Volume Breakpoint) for universal
volume calculation. The illustration indicates how you can set secondary indexes to
specific functions.
A B C
P054 [1.6] = 2m P054 [1,3] = 1.5m P054 [1,1] = .75m
P054 [2.6] = 8m P054 [2.3] = 5.5m P054 [2.1] = 2.75m
P054

1 2

A [6 = 8m]
[6 = 2m] A
B [3 = 5.5m]

[3 = 1.5m] B

C [1 = 2.75m]
[1 = 0.75m] C

• P054 [1,1] = .75m sets breakpoint 1 on transducer 1 to .75m.

• P054 [2.1] = 8m sets breakpoint 1 on transducer 2 to 2.75m.

Starting Measurement
The MultiRanger startup varies between single and dual point models.

Single Point Models

The MultiRanger starts in DISTANCE mode with the transducer preset for the XPS-10 and
an empty distance of 5 meters. Change the following parameters to reflect your
application parameters.

Parameter Index Value Description

P001 G 1 Operation = level
P002 G 1 Material = liquid
P003 G 2 Maximum Process Speed = medium
P004 G 104 Transducer = XPS-15
Operation

P005 G 1 Units = meters

P006 G 12 Empty = 12m
mmmmm

P007 G 10 Span = 10m

Page 32 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Average or Differential [MR 200 only]
For differential or average operation with a single-point MultiRanger, set P001 to 4
(differential) or 5 (average) and connect two transducers of the same type. All of the
relevant parameters then become indexed by the correct transducer:

Index Description
2 indexed by Transducer One or Two
3 indexed by level measurement
1 = Transducer One
2 = Transducer Two
3 = Calculated Level (average or difference)

Dual Point Models

The MultiRanger starts in an OFF state and does not take level measurements. For
measurement setup, configure these basic parameters:
If the application uses two measurement points, provide the basic information for each
measurement point separately:
Parameter Index Value Description
1 1 Operation = level
P001
2 3 Operation = distance
1 1
P002 Material = Liquid
2 1
1 2 Max. Process Speed = medium
P003
2 3 Max. Process Speed = fast
1 104 Transducer = XPS - 15
P004
2 102 Transducer = XPS - 10
P005 G 1 Units = meters
1 12 Empty = 12m
P006
2 4 Empty = 4m
1 11 Span = 11m
P007
2 3.5 Span = 3.5m
Operation
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 33

 Average or Differential [MR 200 only]
For differential or average operation dual-point MultiRanger, set P001 to 4 (differential) or
5 (average) and connect two transducers of the
same type.
All the relevant parameters are then indexed by the
3 Relay Number

correct number: Ring indicates

relay is configured

Dot indicates relay

is energized/de-
energized
Index Description
2 indexed by Transducer One or Two
3 indexed by level measurement
1 = Transducer One
2 = Transducer Two
3 = Calculated Level (average or difference)

Measurement Conditions
The following information will help you configure your MultiRanger for optimal
performance and reliability.

Response Rate
The response rate of the device influences the measurement reliability. Use the slowest
rate possible with the application requirements.
The response rate is also important to functions connected to the filling or emptying
indicators.

Dimensions [MR 200 only]

The dimensions of the vessel, wet well, or reservoir (except empty and span) are only
important if you require volume.
Volume is required to report the level value in terms of volume. The pumped volume
function can also report pumped volume or pump efficiencies.

Failsafe
The failsafe parameters ensure that the devices controlled by the MultiRanger default to
an appropriate state when a valid level reading is not available.
• P070 – Failsafe Timer activates if an error condition is detected. Upon expiration of
the timer, relay status defaults to values based on P071.
• P071 – Failsafe Material Level determines the level reading if the Failsafe Timer
Operation

expires and the unit is still in an error condition.

mmmmm

• P129 – Relay Failsafe controls the reaction of each relay. See Relay Failsafe on page
39 for more information.
If Failsafe Operation activates frequently, see the Troubleshooting Appendix on page 226.

Page 34 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Relays
Relays are the primary controls of external devices such as pumps or alarms.

Relays
mmmmm
The MultiRanger comes with extensive control and alarm functions.

General Introduction
Six onboard multi-purpose relays are provided on the MultiRanger. Each relay may be
independently assigned to one function and has a corresponding status icon on the LCD.
The relay functions fall under three modes of operation:
Mode Function
alarm alarm ON = LCD Icon ON = relay coil de-energized
pump pump ON = LCD Icon ON = relay coil energized
miscellaneous contact closed = LCD Icon ON = relay coil energized

Relay Function
Alarm
Level
In high alarm, the function goes on when the level rises to the ON setpoint and goes off
when the level lowers to the OFF setpoint. In low alarm, the function goes on when the
level lowers to the ON setpoint and goes off when the level rises to the OFF setpoint.

In Bounds [MR 200]

The relay will be in alarm if the level is inside the zone between the setpoints.

Out of Bounds [MR 200]

The relay will be in alarm if the level is outside the zone between the setpoints.

Rate of Change [MR 200]

In filling alarm, the function goes on when the rate of filling increases to the ON setpoint
and goes off when the rate of filling drops to the OFF setpoint. In emptying alarm, the
function goes on when the rate of emptying increases to the ON setpoint and goes OFF
when the rate of emptying drops to the OFF setpoint. For emptying alarm, the setpoints
must be entered as negative values.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 35

 Temperature [MR 200]
In high alarm, the function goes on when the temperature rises to the ON setpoint and
goes off when the temperature lowers to the OFF setpoint. In low alarm, the function
goes on when the temperature lowers to the ON setpoint and goes off when the
Relays

temperature rises to the OFF setpoint.

mmmmm

Loss of Echo
The function goes on when the fail-safe timer expires. The function goes OFF when a
valid echo is received (fail-safe timer is reset).

Pump
Level
In pump down, the function goes on when the level rises to the ON setpoint and goes off
when the level lowers to the OFF setpoint. In pump up, the function goes on when the
level lowers to the ON setpoint and goes off when the level rises to the OFF setpoint.

Miscellaneous
Totalizer and Samplers [MR 200]
Refer to Totalizing Pumped Volume on page 59. Relays are normally de-energized, contact
closure is approximately 200 mSec duration.

Setpoint - ON / OFF
If the ON setpoint is higher than the OFF setpoint, the relay operates as:
• high alarm
• pump down control
If the ON setpoint is lower than the OFF setpoint, the relay operates as:
• low alarm
• pump up control
The ON and OFF setpoints can not be the same on an individual relay but may be common
to other relays. The dead band or hysteresis is the difference between the ON and OFF
setpoints. For in and out of bounds level alarms, the hysteresis is set at ± 2 % of span
from either boundary.

Page 36 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Relay Status – Non Run Modes
When the fail-safe timer expires, pump control relays respond as previously described.
However, alarm relays will respond in the following manner:

Relays
Relay Status

mmmmm
Fail-Safe Mode
High Alarm Low Alarm
Fail-Safe High ON OFF
Fail-Safe Low OFF ON
Fail- Safe Hold HOLD HOLD
Upon entering the program mode, all pump control relays will be turned OFF. Alarm relays
will hold their prior status.

Cautions:
• If the relay status can affect plant operation or personnel safety, it is advisable to
override the relay functions or disconnect the relay wiring during calibration or
simulation.
• Keep power disconnected at main breaker when MultiRanger cover is opened.

Relay States
The relays on the MultiRanger are completely programmable, allowing for any control
scheme.

Relay Types
Relay 1,2,4,5 – NO (Form A)
Relay 3,6 – NO / NC (Form C)

Relay Related Parameters

Some parameters affect how relays react during normal conditions:

P100–Preset Applications [MR 200 only]

Sets the MultiRanger to a preset application. These preset applications quickly set up the
MultiRanger with a minimum number of parameters.

P111–Relay Control Function

Sets the default state differently, depending on whether the relay is programmed as an
alarm or a control.

P111–Alarm Functions
The alarm function de-energizes the relay coils. During normal operation (no alarms), the
relay coils are energized.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 37

 P111–Control Functions
The control function energizes the relay coils. When the instrument is at rest (no controls
operating) the relay coils are de- energized.
Relays

P112–Relay ON Setpoint
mmmmm

Sets the process point at which the relay is tripped.

P113–Relay OFF Setpoint

Sets the process point at which the relay is reset.

P118–Relay Output Logic

Affects relay reaction. Reverses the logic (normally-open to normally-closed or vice
versa).

P129–Relay Failsafe
Changes how individual relays react to a failsafe condition on the instrument.

Relay Wiring Test

P119–Relay Logic Test
Checks the application wiring by forcing a relay control function, such as a level alarm or
pump control setpoint. Ensure all the relay programming and wiring works properly.
Please verify that ON and OFF respond correctly. Use P119 as a final test once all of the
relay programming is done.

Relay Activation
The flexibility of the relay functions ensures that the MultiRanger can support relay
wiring for different systems and applications. Use the following as a guide to the most
common parameters.

Relay Setpoints and Functionality

[MR 100]: When a setpoint is reached, the corresponding action is taken. The setpoint
can be an ON or OFF setpoint related to a process variable.
[MR 200]: The setpoint can be an ON or OFF setpoint related to a process variable, or a
timed setpoint based on interval and duration.

Page 38 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 [MR 100]: Functions affected by setpoint are configured by parameters that determine the
application requirements such as timing. P111 Pump and Control functions (see page 130)
sets the functions requirements.
[MR 200]: Functions affected by setpoint are configured by parameters that determine the

Relays
application requirements such as timing. P111 Pump and Control functions (see page 130

mmmmm
sets the function requirements. Other function parameters:
• P132–Pump Start Delay
• P133–Pump Power Resumption Delay
• P645–Relay Duration

Relay Logic is Modified

Normal operating conditions means that alarms are off and pumps are on. This can be
reversed using P118–Relay Output Logic.

Relay Failsafe
P129–Relay Failsafe
Adjusts how individual relays react to a failsafe condition. Relays can be set to:
• OFF Control is by P071–Failsafe Material Level
• HOLd Keeps the relay in the current state
• dE De-energizes the relay (default for pump controls)
• En Energizes the relay

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 39

 Preset Applications
Preset applications set up the relay parameters to predetermined values shown below:
Relays

Value # Parameters Affected

mmmmm

Off 0 All relays set to OFF

Wet Well 1 Pump down with the following settings:
Parameter Relay #
1 2 3 4 5 6
1 P111 52 52 1(H) 1(L) 0 0
P112 70% 80% 90% 10% – –
P113 20% 20% 85% 15% – –
Wet Well 2 Pump down with the following level and rate settings:
Parameter Relay #
1 2 3 4 5 6
P111 52 52 1(H) 1(L) 0 0
P112 70% 80% 90% 10% – –
2
P113 20% 20% 85% 15% – –
P121 1
Because the pumps are started by rate, you must change P703 to desired
empty rate.
Reservoir 1 Pump up with the following level settings:
Parameter Relay #
1 2 3 4 5 6
3 P111 52 52 1(H) 1(L) 0 0
P112 30% 20% 90% 10% – –
P113 80% 80% 85% 15% – –
Reservoir 2 Pump up with the following level and rate settings:
Parameter Relay #
1 2 3 4 5 6
P111 52 52 1(H) 1(L) 0 0
P112 20% 20% 90% 10% – –
4
P113 80% 80% 85% 15% – –
P121 1
Because the pumps are started by rate you must change P702 to desired
fill rate.
Screen Differential control of a screen or rake:
Parameter Relay #
1 2 3 4 5 6
5 P110 3 1 2 3 0 0
P111 50 1(H) 1(L) 1(H) – –
P112 80% 90% 10% 90% – –
P113 20% 85% 15% 10% – –
Alarms General alarms at four setpoints:
Parameter Relay #
1 2 3 4 5 6
6 P111 1(H) 1(L) 1(HH) 1(LL) 0 0
P112 80% 20% 90% 10% – –
P113 75% 25% 85% 15% – –

Page 40 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Backup Level Override
Backup level override provides the option of overriding the ultrasonic input with another
contacting point level device, for example, the Pointek CLS 200. The ultrasonic reading is
fixed at the programmed switch level until the discrete input is released and the
ultrasonic device makes its decisions based on the override value.

Backup Level Override Parameters

Backup Level Override

P064: Reading Override Enable
Sets the discrete input as the source of a level reading override.

mmmmm
P065: Reading Override Value
Substitutes value for current reading when the discrete input (P064) is enabled. Value is
added in current units and is valid only for the following:
• level
• space
• distance
• difference
• average modes of operation
• head level in OCM mode
Example:
A high level backup switch is connected to Digital Input Two in the same application as
Transducer One at level value 4.3 m.
Settings

Parameter Index Value

P064 1 2
P064 2 0
P065 1 4.3
P065 2 –
When the level rises to 4.3 m and the switch is activated, the reading is forced to 4.3 m
where it stays until the switch is de-activated.

P066: Override Time Delay

Sets the time (in seconds) used to calm the override condition input.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 41

 Discrete Inputs

Wiring the Discrete Inputs

Normal state is standard operation, with the MultiRanger sensing the material level and
controlling the pumps.
The discrete input contacts are either normally-open or normally-closed when the
system state is normal.
Example:
Normal state for a backup high level switch is open, and the contacts on the discrete
input are wired as normally-open.
See Discrete Inputs on page 16 for complete details on wiring the discrete inputs. To
override a level using a discrete input, see Backup Level Override on page 41.

Programming the Discrete Input Logic

The P270 series of parameters permits control over the discrete input.
Discrete Inputs

DI State P270 Setting

Normally Open P270 = 2
mmmmm

Normally Closed P270 = 3

The current value of the discrete input is reported in P275:

P275 Setting MultiRanger State

0 Normal State
1 Exception State

Page 42 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

mA I/O
To integrate the MultiRanger with other equipment, use the mA input and outputs.

Note: When a mA input parameter is accessed, a mA symbol appears in the upper left
corner of the LCD display.
The mA input can be used as a level measurement or can be passed on to a SCADA
system.

mA Input [MR 200]

Level Reading Parameters
Parameter Index Value Description
P004 1 250 Transducer = mA input 1
P250 1 2 Scale = 4 to 20 mA
P251 1 0 4 mA = 0% of span
P252 1 100 20 mA = 100% of span
P253 1 0 Do not damp the input signal
To pass the mA input on to a SCADA system, read the value from the appropriate
communication registers. For more information, go to the MultiRanger Communications
section on page 83.

mA Output
The MultiRanger has two mA outputs, used to send measurements to other devices.
Configuring the mA output to send a 4 to 20 mA signal scaled from 10% to 90% of span of
the second transducer:
Parameter Index Value Description
P200 1 2 set to 4 to 20 range
mA I/O
mmmmm

P201 1 1 send mA proportional to level reading

P202 1 2 base mA on level point 2
P210 1 10 set 4 mA at 10% of span1
P211 1 90 set 20 mA at 90% of span2
P219 1 0 set failsafe action as 0 mA
1.
If the level reading drops below 10% of span, the mA output drops below
4 mA.
2.
If the level reading rises above 90% of span, the mA output rises above
20 mA.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 43

 Calibrating 4 mA Output
1. Connect the mA receiving device to the MultiRanger.
2. Put the MultiRanger into PROGRAM mode.
3. Set P911–mA Output Value to 4.0.
4. View the mA level on the receiving device.
5. If there is a discrepancy, use P214–4 mA Output Trim to correct the value.
Press MODE and then the ARROWs to increase or decrease the trim.
6. Repeat until the mA level on the receiving device equals 4.0 mA.

The unit is now calibrated for 4 mA for the receiving device.

Calibrating 20 mA Output
1. Connect the mA receiving device to the MultiRanger.
2. Put the MultiRanger into PROGRAM mode.
3. Set P911–mA Output Value to 20.0.
4. View the mA level on the receiving device.
5. If there is a discrepancy, use P215–20 mA Output Trim to correct the value.
Press MODE and then the ARROWs to increase or decrease the trim.
6. Repeat until the mA level on the receiving device equals 20.0.

The unit is now calibrated for 20 mA for the receiving device.

Verifying the mA Range

Checks that the external device can track the entire 4 to 20 mA range sent by the
MultiRanger.
1. Use P920 to put the MultiRanger into Simulation mode (see page 79).
2. Run the simulation through one complete fill / empty cycle.
3. View P911–mA Output Value to verify that it tracks to the simulation.
4. View the mA value reported on the external equipment to verify that it also tracks to
the simulation.
mA LI/O
mmmmm

Page 44 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Volume [MR 200]
Volume is a feature of the MultiRanger 200 only. Volume is used in two situations:
1. Calculate and display volume instead of level. For programming all setpoint
parameters in terms of volume units rather than level units.
2. Calculate pumped volume to accomplish the following:
• Totalize the volume of material that is pumped out of the wet well
• Set an alarm on pump efficiency
If you require this functionality, please contact your local Siemens Milltronics
representative at [Link] .

Readings
When using volume, readings are given in arbitrary units specified in P051.
The default is 100, which gives a reading in percent of total. Use whatever units you want
here. If the value is too large for the four-digit LCD, use a larger unit.

Example
If a wet well has a maximum capacity of 250,000 liters, use the value 250.0 for P051 and
set the reading in 1000s of liters.

Tank Shape and Dimensions

There are many common tank shapes to select from. (See P050. If possible, use one of
these.) Each tank shape uses the Empty distance (P006) in its calculations of volume.
Some tank shapes also require extra dimensions to calculate the volumes. Do not
estimate these values. They must be correct to ensure the accuracy of your volume
calculations.

To configure volume for a tank with a half-sphere bottom, set the

following:

Parameter Index Value Description

P050 1 4 selects the correct tank shape
P051 1 100 sets maximum volume at 100 (percent)
P052 1 1.3 sets A to 1.3m
Volume

Notes:
mmmmm

• The default reading changes to a range from 0 to 100 (the value in P051)
• Empty (P006) is still measured to the bottom of the tank, not the top of A.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 45

 Characterization Chart [MR 200]
If you cannot use a pre-defined tank, then use one of the universal tank shapes and
program the characterization curve.
1. Plot a volume to height chart. Usually a tank supplier will provide this chart.
However, if you have a custom-built wet well then you will need access to complete
drawings of the well or accurate measurements.
2. Enter the curve values from this chart into P054 and P055.
3. Ensure extra points are added around sharp transitions in the wet well volume (e.g:
as steps in the well wall).

Note: The end points in the curve are 0,0 (fixed) and the point defined by P007–Span
and P051–Maximum Volume.

Example Chart
MAX VOLUME
P051
VOLUME (P055)

FLOW

0,0
LEVEL (P054)
Volume
mmmmm

Page 46 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

MultiRanger 200 only
Parameter Transducer Index Value Description
1 0.0
2 0.8
3 2.0
4 3.5
5 4.1
6 4.7
7 5.1
8 5.2 Determines the Level breakpoints at
P054 1
which the volumes are known.
9 5.3
10 5.4
11 5.5
12 5.6
13 6.0
14 7.2
15 9.0
1 0.0
2 2.1
3 4.0 Determines the volumes which
correspond to the level breakpoints.
4 5.6
The universal calculations interpret
5 5.9
between the breakpoints to produce
6 6.3 an accurate model of the volume at
7 6.7 all level readings.
P055 1 8 7.1
9 7.8 Settings
10 8.2 P050 = 9 for linear approximation
11 8.8 P050 = 10 for curved approximation
12 9.2
13 10.9 Linear approximation uses a linear
14 13.0 algorithm; curved approximation
uses a cubic spline algorithm.
15 15.0
Volume
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 47

 Alarms Alarms

Level
mmmmm

The level alarm is the most common. Use this alarm to warn you when your process is in
danger of being upset due to high or low levels.
Generally, the four alarms used are Hi, Hi Hi, Lo, and Lo Lo.

Set the Common Parameters

P006
hi hi
hi
P007
lo
lo lo

Prerequisite: You must know the details of your application and substitute the values for
the sample values provided. If you are bench testing the unit, then set your test values to
be the same as the sample values.

Parameter Index1 Value Description

P001 G 1 Operation = level
P002 G 1 Material = liquid
P003 G 2 Maximum Process Speed = medium
P004 G 102 Transducer = XPS-10
P005 G 1 Units = meters
P006 G 1.8 Empty = 1.8m
P007 G 1.4 Span = 1.4m
1.
This example assumes a base, single measurement unit. If your unit has
optional dual point software installed then some parameters are indexed by
two.

Page 48 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Setting Simple Level Alarms
To set Relay Five to a standard level alarm (Hi Hi, Hi, Lo, Lo Lo) do the following:

Parameter Index Value Description

Alarms
mmmmm
P111 5 1 • Set P111, indexed to relay, to the value 1 for level
alarm
• Press UNIT to display the Auxiliary Function
symbol.
• Press ARROW keys as required to scroll
to the alarm designation ( , , , or ).
• Press ENTER to enter the value.
P112 5 1.2m • Set the ON setpoint
P113 5 1.15m • Set the OFF setpoint

Available designations:
Alarm Designation
Hi Hi
Hi
Lo
Lo Lo

Rate [MR 200]

Rate alarms can trigger an alarm if the vessel is filling/emptying too quickly.

Setting a Filling Rate Alarm

Parameter Index Value Description
P111 5 4 These settings trip the alarm when the
P112 5 1m reservoir is filling faster than 1m per minute
P113 5 0.9m and reset it at 0.9m per minute.

Setting an Emptying Rate Alarm

Parameter Index Value Description
P111 5 4 These settings trip the alarm when the
P112 5 -10% reservoir is emptying faster than 10% of span
P113 5 -5% per minute and reset the alarm when
emptying falls to 5%.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 49

 In Bounds/ Out of Bounds Range [MR 200]
Use the bounded range alarms to detect when the level is inside or outside of the range.
By using a bounded range alarm, you can effectively put two level alarms (high and low)
Alarms

on one relay.
mmmmm

Setting an Out of Bounds Alarm

Parameter Index Value
P111 5 3
P112 5 1.3
P113 5 0.3
P116 5 0.05
Results:
• Trips alarm above 1.35m and below 0.25m
• Resets alarm below 1.25m and above 0.35m

Setting an In Bounds Alarm

Parameter Index Value
P111 5 2
P112 5 1.3
P113 5 0.3
P116 5 0.05
Results:
• Trips alarm below 1.25m and above 0.35m
• Resets alarm above 1.35m and below 0.25m

Cable Fault
Activates an alarm if transducer cable circuit enters a shorted or opened state.

Parameter Index Value Description

P111 5 7 Alarm on transducer cable fault
P110 5 1 Alarm on Transducer One

Temperature [MR 200]

Use the temperature alarm to activate an alarm when the temperature reaches the ON
setpoint (P112). This alarm uses the same setpoint parameters as the level alarms (P112
and P113).

Page 50 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 With P112 and P113, you can set a high alarm (P112 > P113) or a low alarm (P112 < P113).

This shows a high alarm:

Parameter Index Value Description

Alarms
mmmmm
P111 5 5 Alarm on temperature
P112 5 45 ON setpoint at 45 °C
P113 5 43 OFF setpoint at 43 °C
P110 5 1 Take the temperature reading from
Transducer One

The temperature source can be the temperature sensor built into the transducer or an
external TS-3, as set by P660.

Loss of Echo (LOE)

Parameter Index Value Description
P110 5 1 Alarm on LOE for Transducer One
P111 5 6 Alarm on LOE
P070 G 0.5 Trip alarm when 0.5 minutes (30 seconds)
pass without detecting a valid echo.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 51

 Pump Control

Setting a Pump Down Group

Example: Sewage Wet Well
Setting a group of three pumps to pump down a wet well.

MultiRanger
Pump Control
mmmmm

P006

Outflow

Inflow
P007

Set the Common Parameters

Prerequisite: Substitute the details of your application in place of the sample values
provided. If you are bench testing the unit, set your test values to be the same as the
sample values.

Parameter Index1 Value Description

P001 G 1 Operation = level
P002 G 1 Material = liquid
P003 G 2 Maximum Process Speed = medium
P004 G 102 Transducer = XPS-10
P005 G 1 Units = meters
P006 G 1.8 Empty = 1.8m
P007 G 1.4 Span = 1.4m
1.
Example assumes a single measurement unit. If your MultiRanger has
dual point software installed then some parameters are indexed by two.

Page 52 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Set Relays to ALTERNATE DUTY ASSIST
Parameter Index Value Description
P111 1 52
Sets the pump relays (index 1, 2, and 3) to
P111 2 52
ALTERNATE DUTY ASSIST.
P111 3 52

Set the ON Setpoints

Parameter Index Value Description
P112 1 1.0m Sets the three setpoints for the pump relays.
P112 2 1.1m The first cycle will use these setpoints.
P112 3 1.2m Subsequent cycles rotate the setpoints
among the pumps.

Pump Control
Set the OFF Setpoints

mmmmm
Parameter Index Value Description
P113 0 0.5m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

Setting a Pump Up (Reservoir) Group

Sets a group of three pumps to pump up a reservoir.

MultiRanger

P006

P007
Inflow

Outflow

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 53

 Set the Common Parameters
Prerequisite: Substitute the details of your application in place of the sample values
provided. If you are bench testing the unit, set your test values to be the same as the
sample values.

Parameter Index1 Value Description

P001 G 1 Operation = level
P002 G 1 Material = liquid
P003 G 2 Maximum Process Speed = medium
P004 G 102 Transducer = XPS-10
P005 G 1 Units = meters
P006 G 1.8 Empty = 1.8m
P007 G 1.4 Span = 1.4m
Pump Control

1. Example assumes a single measurement unit. If your MultiRanger has

mmmmm

dual point software installed, some parameters are indexed by two.

Set Relays to ALTERNATE DUTY ASSIST

Parameter Index Value Description
P111 1 52
Sets the pump relays (index 1, 2, and 3) to
P111 2 52
ALTERNATE DUTY ASSIST.
P111 3 52

Set the Relay ON Setpoints

Parameter Index Value Description
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The first cycle will use these setpoints.
P112 3 0.2m Subsequent cycles rotate the setpoints
among the pumps.

Set the Relay OFF Setpoints

Parameter Index Value Description
P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.
For more information, see Appendix D: Pump Control Reference on page 235.

Page 54 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Other Pump Control Algorithms
Set Relays to ALTERNATE DUTY BACKUP [MR 200]
Parameter Index Value Description
P111 1 53
Sets the pump relays (index 1, 2, and 3) to
P111 2 53
ALTERNATE DUTY BACKUP.
P111 3 53

Set the Relay ON Setpoints [MR 200]

Parameter Index Value Description

Pump Control
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The first cycle will use these setpoints.

mmmmm
P112 3 0.2m Subsequent cycles rotate the setpoints
among the pumps.

Set the Relay OFF Setpoints [MR 200]

Parameter Index Value Description
P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

Set Relays to FIXED DUTY ASSIST

Parameter Index Value Description
P111 1 50 Sets the pump relays (index 1, 2, and 3) to
P111 2 50 FIXED DUTY ASSIST. Multiple pumps can run
P111 3 50 simultaneously.

Set the Relay ON Setpoints

Parameter Index Value Description
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The first cycle will use these setpoints.
P112 3 0.2m Subsequent cycles rotate the setpoints
among the pumps.

Set the Relay OFF Setpoints

Parameter Index Value Description
P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 55

 Set Relays to FIXED DUTY BACKUP [MR 200]
Parameter Index Value Description
P111 1 51 Sets the pump relays (index 1, 2, and 3) to
P111 2 51 FIXED DUTY BACKUP. Only one pump will
P111 3 51 ever run at one time.

Set the Relay ON Setpoints [MR 200]

Parameter Index Value Description
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The setpoints remain attached to the pump
P112 3 0.2m relays.
Pump Control

Set the Relay OFF Setpoints [MR 200]

mmmmm

Parameter Index Value Description

P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

Set Relays to ALTERNATE DUTY SERVICE [MR 200]

Parameter Index Value Description
P111 1 54
Sets the pump relays (index 1, 2, and 3) to
P111 2 54
SERVICE RATIO DUTY ASSIST
P111 3 54
P122 1 25 Sets the ratio to: 25% – Pump One
P122 2 50 50% – Pump Two
P122 3 25 25% – Pump Three

Set the Relay ON Setpoints [MR 200]

Parameter Index Value Description
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The first cycle will use these setpoints.
P112 3 0.2m Subsequent cycles rotate the setpoints
among the pumps.

Set the Relay OFF Setpoints [MR 200]

Parameter Index Value Description
P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

Page 56 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Set Relays to FIRST IN FIRST OUT (FIFO) ASSIST [MR 200]
Parameter Index Value Description
P111 1 56 Sets the pump relays (index 1, 2, and 3) to
P111 2 56 FIFO DUTY ASSIST.
P111 3 56

Set the Relay ON Setpoints [MR 200]

Parameter Index Value Description
P112 1 0.4m Sets the three setpoints for the pump relays.
P112 2 0.3m The first cycle will use these setpoints.
P112 3 0.2m Subsequent cycles rotate the setpoints

Pump Control
among the pumps.

mmmmm
Set the Relay OFF Setpoints [MR 200]
Parameter Index Value Description
P113 0 1.3m By using index 0 all six relays are set at the
same time, including any alarm relays. Use
with caution.

Optional Pump Controls

Starting Pumps by Rate of Level Change [MR 200]
Use this function when multiple pumps will be controlled by rate of level change rather
than setpoints. Pumping costs can be reduced because only the highest ON setpoint
needs to be programmed. This results in a lower difference in head to the next wet well
which, in turn, results in less energy being used to pump out the well.

Parameter Index Value Description

P112 1 1.35 Starting pumps by rate allows all setpoints to
P112 2 1.35 be set higher to save money by pumping from
P112 3 1.35 the highest safe level of the wet well.
P113 1 0.5m
P113 2 0.5m Notice that all indexed relays for both P112
and P113 are set to the same levels.
P113 3 0.5m
P121 1 1
The pumps will start on 20 second intervals
P121 2 1 until the rate set in P703 is met.
P121 3 1
P132 G 20.0

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 57

 When the first ON setpoint is reached, the pumps will start, one by one, until the material
level rate of change is set at the same value or greater than the value in:
• P703 – Emptying Indicator (pump down applications)
• P702 – Filling Indicator (pump up applications)
Set delay between pump starts using P132 – Pump Start Delay.

Single and Dual Point [MR 200]

• Single Point Mode: one pump by rate control available that affects all pumps.
• Dual Point Mode: a single pump by rate control can be set up for each of the three
available level points. Set Operation for difference or average (P001 = 4 or 5).

Notes:
Pump Control

• Set all pump control relay ON and OFF setpoints to the same value
• If the level is within 5% of Span (P007) of the OFF setpoint, then the next pump is
mmmmm

not started

Rotating Pumps by Service Ratio [MR 200]

Prerequisite: Set pump relays to a service ratio value (P111 = 54 or 55).

Parameter Index Value Description

P122 1 1 These values will start Pump Two 50% of the
P122 2 2 time and Pumps One and Three each 25% of
P122 3 1 the time.

Notes:
• The MultiRanger will not sacrifice other pumping strategies to ensure that the ratio
is held true
• If the pump relays are set to the same value, then the ratio equals 1:1 and all pumps
are used equally (preset)

When more than one pump is assigned a Pump Service Ratio value (in any time units) and a
pump start is required (P112 Relay Setpoint ON), the pump with the fewest running hours (with
respect to the assigned ratio values) starts.
Conversely, when a pump stop is required (113 Relay Setpoint OFF), the pump with the
most running hours (as compared to the assigned ratio values) stops.

Page 58 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Totalizing Pumped Volume [MR 200]
Prerequisite: the volume of the vessel must be known.

Parameter Index Value Description

P001 G 7 Operation = pumped volume
P002 G 1
P003 G 2
P004 G 102
These parameters are as shown above.
P005 G 1
P006 G 1.8
P007 G 1.4
P050 G 1 Tank shape is Flat Bottom.

Pump Control
P051 G 17.6 Max volume is 17.6m3 or 17,600 liters.
P111 1 52

mmmmm
Sets relays 1, 2, and 3 as a pump group using
P111 2 52 ALTERNATE DUTY ASSIST CONTROL.
P111 3 52
P112 1 1.0
P112 2 1.2 Sets the ON setpoints for the pump group.
P112 3 1.4
P113 0 0.2 Sets the OFF setpoints for the pump group.

Set in RUN Mode

1. Press PROGRAM for RUN mode.

2. Press TOGGLE to display pumped volume on the totalizer.

3. Press AUXILIARY P to display current level in the auxiliary reading area.

Setting Independent Failsafe Controls

Independent failsafe controls allow you to vary an individual relay from the global failsafe
controls programmed in P070 to P072.
Example:

The global failsafe controls are set to hold and Relay Five is set to trigger an alarm bell.

Parameter Index Value Description

P071 G HOLd Keep level at last known value.
P129 5 dE De-energize Relay Five, and trigger alarm.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 59

 Setting a Pump to Run On [MR 200]
When you need to pump below the normal OFF setpoint, use P130 (Pump Run-On Interval)
and P131 (Pump Run-On Duration) to control this event.
Example:
The pump connected to Relay Three is set to pump for an extra 60 seconds every five
times it is triggered.

Parameter Index Value Description

P130 3 5 Wait for Relay Three to pump five times and
then run-on.
P131 3 60 Run-on for 60 seconds.
Pump Control
mmmmm

Note: P130 counts when the indexed relay is tripped, not the number of pump cycles. If
the indexed relay only trips once every four pump cycles then the actual interval of the
run-on will be 20 pump cycles, or five cycles of Relay Three.

Setting the Pump Start Delays [MR 200]

The pump start delay ensures that all of the pumps do not start at once to avoid power
surges. There are two parameters used here: P132–Pump Start Delay and P133–Pump
Power Resumption Delay. The default is 10 seconds but you can increase this if your
pumps take longer to spin up.
Example:
The delay between pumps is set to 20 seconds and the delay of the first pump is set to 30
seconds.

Parameter Index Value Description

P132 G 20 Wait at least 20 seconds between pump
starts.
P133 G 30 Wait for 30 seconds when power is restored.

Reducing Wall Cling [MR 200]

Use the Wall Cling parameter to randomly alter the ON and OFF setpoints over a range.
This eliminates the ridge of material that builds up at the setpoint that can give false
echoes.
This setting may increase the number of days between trips to clean the wet well.
Wall cling reduction is set by P136. The relay setpoints ON and OFF are randomly varied
inside a range so the material level does not stop at the same point.

Page 60 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Example [MR 200]:
A range of 0.5 meters is used to vary the setpoint. The randomly-selected setpoints are
always inside the ON and OFF setpoints.

Level Setpoint ON

Random Setpoint Wall Cling Value

Range

Pump Control
Level Setpoint OFF

mmmmm
Grouping Pumps [MR 200]
You can group pumps and use the same pumping algorithm separately on each group. If
you specify different pumping algorithms then the pumps are already grouped by
algorithm and you do not need to use this parameter.
Group pumps only when four pumps are using the same algorithm and you want to split
them into two groups.
Example:
Pumps One and Two can operate as a group and Pumps Three and Four can operate as
another group.

Parameter Index Value Description

P137 1 1
Groups Pumps One and Two
P137 2 1
P137 3 2
Groups Pumps Three and Four
P137 4 2

Setting a Flush Valve [MR 200]

A flush valve stirs up the sediment on the bottom of the well during pumping so that it
doesn’t accumulate. These parameters will control any relays set with P111 = 64 (Flush
Valve).
Most sets of parameters will work with only one or two changes; however, for these
parameters to work, all of them must be set to a value.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 61

 Example:

The flush valve connects to Relay Four and the watched pump is on Relay One.

Parameter Index Value Description

P170 G 1 Watch Relay One to count pump cycles.
P171 G 3 Open the flush valve for 3 cycles.
P172 G 10 Use the flush value every 10 cycles.
P173 G 120 Open the flush valve for 120 seconds.

Relay Controlled by Communications

A relay can be controlled directly by a remote system through communications. No other
control schemes can then be used with a relay configured this way. Communications can
Pump Control

be used to force status of some control relays, such as pumps.

mmmmm

Settings:

Parameter Index Value Description

P111 5 65 Sets Relay Five to communications control.

Tracking Pump Usage

You can find out how much an individual pump has been used by viewing the pump
records parameters.

Information Available Parameter Access

Current RUN time P309
Total pump hours P310
Total pump starts P311
Total pump RUN on occurrences P312 [MR 200 ONLY]

Page 62 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Rake (Screen) Control [MR 200]
This feature is only available on the MultiRanger 200.
Screens or rakes are mounted on the inflow channel of the wastewater treatment plant
to prevent debris from clogging the equipment.
When material builds up on the screen, a level differential is created, and the water level
is higher in front of the screen than behind it. When this differential reaches the
programmed setpoint, the MultiRanger activates a relay to operate mechanical rakes that
clean the screen and ensure a steady flow.

Setting a Rake Control

Transducer
Transducer Two
One Rake

Rake (Screen) Control

MR 200

mmmmm
Transducer[1] Note: transducers may be mounted at variant heights.

Debris Conveyer Transducer[2]

P006[1]

P006[2]
P007[1]
P007[2]

h[1] Flow
Rake
Water Level h[2]

Point Three: Level Distance = h[1] –h[2]

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 63

 Setting the Common Parameters
Prerequisite: Substitute the details of your application in place of the sample values
provided. If you are bench testing the unit, set your test values to be the same as the
sample values.
Parameter Index Value Description
P001 G 4 Operation = Differential
P002 G 1 Material = liquid
P003 1,2 2 Max. Process Speed = medium
P004 1,2 102 Transducer = XPS-10
P005 G 1 Units = meters
P006 1 1.8 Empty = 1.8m
2 2.2 Empty = 2.2m
P007 1 1.4 Span = 1.4m
2 1.4 Span = 1.4m

Set Relay 1 (Operate Rake)

Parameter Index Value Description
P110 1 3
Starts the rake when the difference between the
P111 1 50 two levels rises above 0.4m and stop the rake
Rake (Screen) Control

P112 1 0.4 when the difference falls below 0.1m.

P113 1 0.1
MR 200

Set Relays 2 to 4 (Level Alarms)

P110 2 1 Description
P110 2 1
Sets Relay Two as a high level alarm for
P111 2 1 Transducer One with an ON setpoint of 1.3m
P112 2 1.3 and an OFF setpoint of 1.2m.
P113 2 1.2
P110 3 2
Sets Relay Three as a low level alarm for
P111 3 1 Transducer Two with an ON setpoint of 0.2m
P112 3 0.2 and an OFF setpoint of 0.4m.
P113 3 0.4
P110 4 3 Sets Relay Four as a rake failure alarm as it
P111 4 1 uses the differential level point (3) with an
P112 4 1.0 ON setpoint of 1.0m and an OFF setpoint of
P113 4 0.9 0.9m.

Page 64 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

External Totalizers and Flow Samplers
[MR 200]
This feature is only available on the MultiRanger 200.
External totalizers are simple counters which count the number of relay clicks produced
by the MultiRanger. This is generally used to keep track of OCM or pumped volume totals.
Note that both of these values are also stored in the MultiRanger and are available
through communications.
Flow samplers are devices which take a sample of liquid when triggered by a relay click.
These samples are used to monitor water quality over time. Flow samplers can be driven
by OCM volume or by relay click volume settings depending on the application
requirements.

Relay Contacts
Pumped volume is calculated at the end of the pump cycle. Totalized volume given
through a relay set up for totalizer (P111[r]=40) will be given in bursts at this time.
Both the open and closed times for the relay contact are provided by P645 and are preset
to 0.2 seconds. Partial units are added to the next pump cycle.

Example:

Shows a relay set up to make one contact for every cubic metre (m3) of liquid.

P645 P645

Flow Samplers – MR 200

External Totalizers and
4m3 2m3 2m3 3m3 1m3
mmmmm

Pump Cycle

Totalizer
To set the totalizer to provide relay contact to an external counter, use the following:

Counter Formula
1 Contact per 10P640 units P640 is preset to 0 so the default number of
contacts for a pumped volume cycle is
equivalent to the number of volume units.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 65

 The source of units depends on the operation:
Operation Units Source Parameter
OCM (P001=6) P604–Maximum Flow, or P608–Flowrate Units
Pumped Volume (P001=7) P051–Max Volume

Flow Sampler
Based on Volume and Time
To trigger a flow sampler relay based on flow, use P111[r]=41 and set the other
parameters:

Counter Formula
1 Contact per P641 x 10P642 units

Operation Units Source Parameter

OCM (P001=6) P604 – Maximum Flow, or P608 – Flowrate Units
By using a mantissa (P641) and an exponent (P642), the relay contacts can be based on a
volume other than a multiple of ten.
During the periods of low flow, the sampler may be idle for lengths of time. Program P115
to a time interval in hours to drive the sampler. The sampler will operate based on the
volume of flow or the time interval, whichever comes first.
Flow Samplers – MR 200
External Totalizers and
mmmmm

Page 66 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Open Channel Monitoring (OCM)
[MR 200]
An OCM installation is defined one of three ways, based on the Primary Measuring
Device (PMD):

1. Dimensional (P600 = 2,3,6,7)

For some common weir and flume types. PMD dimensions (P602) are entered directly.
• BS-3680 / ISO 1438/1 Thin plate V notch weir on page 69
• BS-3680 / ISO 4359 Rectangular Flume on page 70
• Palmer Bowlus Flume on page 71
• H Flume on page 72

2. Exponential (P600 = 1)
For most other weir and flume types. PMD exponents provided by the manufacturer are
entered. Flow is calculated using the exponent (P601) and the maximum values (P603 and
P604).
• Standard Weirs on page 73
• Parshall Flume on page 74
• Leoplod Lagco on page 75
• Cut Throat Flume on page 76

3. Universal (P600 = 4,5)

For all other PMDs, the head-to-flow curve can be plotted based on known breakpoints,
usually supplied by the PMD manufacturer.
• Typical Flow Characterization on page 77
• Example Flumes on page 78
• Example Weirs on page 78

Common Parameters
These Quick Start parameters are required for all installations.
Parameter Index Value Description
P001 G 6 Operation = OCM
P002 G 1 Material = liquid
Open Channel Monitoring

P003 G 2 Max. Process Speed = medium

P004 G 102 Transducer = XPS-10
P005 G 1 Units = meters
P006 G 1.8 Empty = 1.8m
MR 200

mmmmm

P007 G 1.0 Span = 1.4m

P801 G 0.8 Range Extension to avoid LOE

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 67

 Setting Zero Head
Many PMDs start flowing higher than the traditional empty distance of the application.
You can account for the flow in one of two ways:
1. Use P605 (Zero Head) to have OCM calculations ignore levels below that value.
Possible head = P007 minus P605.

Note: P603 (Max. Head) is preset to P007 and is not updated when P605 is used. Make
sure you set P603 to the correct value when using P605.

P006

P007

P603 P605

2. Use P801 Range Extension where the Empty level is set to the bottom of the weir,
and above the bottom of the channel. It should be used if the surface monitored can
fall past the Empty (P006) level in normal operation without reporting an LOE. The
value is added to Empty (P006) and can be greater than the range of the transducer.

P006
P007
P603

P801
Open Channel Monitoring
MR 200

The examples on the following pages show both methods.

mmmm
m

Page 68 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Setting Totalized Volume
To display the totalized volume on the LCD use the following parameters:

Parameter Index Value Description

P737 G 2 Show the eight digit totalizer in the primary
display

Applications Supported by MultiRanger 200

BS-3680 / ISO 1438/1 Thin plate V notch weir

Front View

Side View
Transducer notch angle

P602 P006

P007
P603
P801

4 to 5 x hmax (hmax = P007)

Plan View Open Channel Monitoring

Parameter Index Value

P600 G 7–ISO 1438/1 V Notch Weir
P602 1 Notch angle
MR 200

mmmmm

(view only) 2 Discharge coefficient (Ce)

P603 G Maximum Head (preset to P007)
P801 G Range Extension
P608 G Flowrate Units

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 69

 BS-3680 / ISO 4359 Rectangular Flume

h Diagonal View

Plan View 4 to 5 x hmax (hmax = P007)

L

Flow

Front View Side View

Transducer

P006
h Flow

P605 (p)

Parameter Index Value

P600 G 6–ISO 4359 Rectangular Flume
P602 1 Approach width (B)
2 Throat width (b)
Open Channel Monitoring

3 Hump Height (p)

4 Throat length (L)
(view only) 5 Velocity coefficient (Cv)
(view only) 6 Discharge coefficient (Cd)
MR 200

(view only) 7 Cross sectional area

mmmm
m

P605 G Zero Head

P608 G Flowrate Units

Page 70 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Palmer Bowlus Flume

Plan View

Flow

D/2, point of Front View

measurement Transducer

Side View

P006
P007
P603

P605

Parameter Index Value

P600 G 2–Palmer Bowlus Flume
P602 1 Flume width (D)
P603 G Maximum Head (preset = P007)
P604 G Maximum Flow
P605 G Zero Head
P606 G Time Units

Application Information
• Sized by pipe diameter D
• Flume relief is trapezoidal
• Designed to install directly into pipelines and manholes
• Head is referenced to bottom of the throat, not bottom of the pipe
• For rated flows under free flow conditions, the head is measured at a distance of
Open Channel Monitoring

D/2 upstream from the beginning of the converging section

MR 200

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 71

 H Flume
Transducer

Flow
Point of Measurement

Plan View

P006
D P007

Front View Side View

Parameter Index Value

P600 G 3–H Flume
P602 1 Flume height (D)
P603 G Maximum Head (preset = P007)
P604 G Maximum Flow
P606 G Time Units
• Sized by maximum depth of flume
• Approach is preferably rectangular, matching width and depth for distance 3 to 5
times the depth of the flume
• May be installed in channels under partial submergence (ratio of downstream level
to head). Typical errors are:
• 1% @ 30% submergence
• 3% @ 50% submergence
• For rated flows under free flow conditions, the head is measured at a point
downstream from the flume entrance

Flume Size Point of Measurement

(Diameter in feet) cm inches
0.5 5 1¾
0.75 7 2¾
1.0 9 3¾
1.5 14 5½
2.0 18 7¼
2.5 23 9
Open Channel Monitoring

3.0 28 10¾
4.5 41 16¼
MR 200

• H flumes come with a flat or sloping floor. The same flow table can be used because
mmmm

error is less than 1%.

m

Page 72 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

PMDs with Exponential Flow to Head Function
For Primary Measuring Devices (PMDs) that measure flow by an exponential equation,
use these parameters. Ensure that you use the correct exponent for your PMD; the values
below are samples only.

Standard Weirs
Transducer

3 to 4
hmax
h

Weir Profile

Applicable Weir Profiles

V-notch or suppressed cipolleti or sutro or

triangular rectangular trapezoidal proportional

Parameter Index Value

P600 G 1 - Exponential Function
P601 G Weir Type Value1
V-notch 2.50
Suppressed rectangular 1.50
Cipolletti or trapezoidal 1.50
Open Channel Monitoring

Sutro or proportional 1.00

P603 G Maximum Head
P604 G Maximum Flow
P606 G Time Units
MR 200

mmmmm

P801 G Range Extension

1. Values are samples only. Consult weir manufacturer’s documentation for
correct flow exponent.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 73

 Non-Applicable Weir Profiles

contracted compound Poebing approximate

rectangular exponential

Flows through these weirs can be measured using the Universal Flow Calculation P600 =
4 or 5. See Universal Calculation Support on page 77.

Parshall Flume

Note: C = Converging Dimension.

Plan View C
2/ C
3

Flow

Front View Side View

Transducer

P006

Application Information
• Sized by throat width
• Set on solid foundation
• For rated flows under free flow conditions, the head is measured at 2/3 the length of
the converging section from the beginning of the throat section
Open Channel Monitoring

Parameter Index Value

P600 G 1–Parshall Flume
MR 200

P601 G 1.22–1.607 (consult your flume documentation)

mmmm
m

P603 G Maximum Head

P604 G Maximum Flow (Q)
P606 G Time Units

Page 74 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Leopold Lagco Flume

Plan View
Throat

Front View

Converging Diverging
Transducer
Point of Measurement
Side View

0
Head

Parameter Index Value

P600 G 1–Leopold Lagco Flume
P601 G 1.55
P603 G Maximum Head (preset P007)
P604 G Maximum Flow
P605 G Zero Head
P606 G Time Units

Application Information
• Designed to be installed directly into pipelines and manholes
• Leopold Lagco may be classed as a rectangular Palmer-Bowlus flume
• Sized by pipe (sewer) diameter
• For rated flows under free flow conditions, the head is measured at a point
upstream referenced to the beginning of the converging section. Refer to the
following table:
Open Channel Monitoring
MR 200

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 75

 Flume Size Point of Measurement
(pipe diameter in inches) cm inches
4-12 2.5 1
15 3.2 1¼
18 4.4 1¾
21 5.1 2
24 6.4 2½
30 7.6 3
42 8.9 3½
48 10.2 4
54 11.4 4½
60 12.7 5
66 14.0 5½
72 15.2 6

Cut Throat Flume

Plan View

Application Information
• Similar to Parshall flume except that the floor is flat bottomed and throat has no
virtual length.
• Refer to manufacturer’s specifications for flow equation and point of head
measurement.

Parameter Index Value

Open Channel Monitoring

P600 G 1–Cut Throat Flume

P601 G 1.55
P603 G Maximum Head (preset P007)
MR 200

P604 G Maximum Flow

mmmm
m

P606 G Time Units

Page 76 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Universal Calculation Support
When the primary measuring device (PMD) doesn’t fit one of the standard types, it can
be programmed using a universal characterization. When Universal is selected as the
PMD type (P600), then both P610 and P611 must be entered to define the flow.
Two curve types are supported:
• P600 = 4–linear (piece wise linear)
• P600 = 5–curved (cubic spline)
Both are shown in the following chart.

Typical Flow Characterization

Maximums (P603, P604)
Flow (P611)

Linear
Curved

Head (P610)

Characterization is achieved by entering the head (P610) and corresponding flow (P611),
either from empirical measurement or from the manufacturer's specification. Increasing
the number of defined breakpoints will increase the accuracy of the flow measurement.
Breakpoints should be concentrated in areas exhibiting the higher degrees of non linear
flow. A maximum of 32 breakpoints can be defined. The curve’s end point is always
specified by the parameters Maximum Head (P603) and Maximum Flow (P604) for a
maximum total of 33 breakpoints.
Max. Flow
Flow Breakpoints

Open Channel Monitoring

Zero Flow
Zero Head

Max. Head

Head Breakpoints
MR 200

mmmmm

Use as many breakpoints as required by the complexity of your PMD.

See Volume on page 45 for more information and parameters P610 and P611 for
characterization.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 77

 Example Flumes
These example flumes would both require a universal calculation.

Trapezoidal

Dual Range (nested) Parshall

Example Weirs
These weirs could require universal calculation.

contracted compound Poebing approximate

rectangular exponential
Open Channel Monitoring
MR 200
mmmm
m

Page 78 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Testing the Configuration

Testing the Configuration

After programming the unit, you must test the device to ensure that it performs to your

mmmmm
specifications. This test can be run in simulation mode or by varying the level in the
application. The latter is preferred as it more accurately represents running conditions.
However, if it is not possible to do a physical test, a simulation will ensure that control
programming is correct.

Simulation
In simulation mode, the LCD display reacts to the simulated level changes. Alarm relays
will also react to the simulation, but any pump or control relays will not react.
To allow pump or control relays to operate on the simulated level, set P000 to –1.

Simulating a Single Measurement

Access the appropriate parameter: (press PROGRAM and then key in the parameter
number). Press TRANSDUCER five times to overcome Echo Lock (P711) if applicable:
the associated Reading is displayed in the Parameter Value field, and any alarm relays
are set accordingly.

To verify Reading calculations (P920 to P926)

1. Key in a material level in Units (P005) or % of Span (P007).
2. Press ENTER to display the calculated Reading.
3. Verify the calculated Reading.
4. To start a simulation from the level entered, press ARROW or .

Simulating a Level Cycle

Starting a (P920, P921, P922, or P923) simulation when level = 0:

1. Press ENTER to simulate level rise and fall. At the start of a simulation, the
default rate is 1% of Span / second.
2. Press the ARROW or to adjust the simulated rate of rise or fall. The
maximum rate is 4% of Span / second.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 79

 Testing the Configuration The effect of the ARROW key is determined by the state (rate of rise or fall) immediately
before the key is pressed.

Action State (prior to pressing key) Effect

mmmmm

Stop Rise at 1% of Span / second

Rise at 1% of Span / second Rise at 4% of Span / second (max.)

Rise at 4% of Span / second (max.) No effect

Press
Fall at 1% of Span / second Stop

Fall at 4% of Span / second Fall at 1% of Span / second

Stop Fall at 1% of Span / second

Rise at 1% of Span / second Stop

Press Rise at 4% of Span / second (max.) Rise at 1% of Span / second

Fall at 1% of Span / second Fall at 4% of Span / second (max.)

Fall at 4% of Span / second (max.) No effect

When the level rises to 100% or falls to 0%, it reverses direction at the same rate.

Checking Volume Characterization [MR 200]

To confirm universal volume calculations (P050 = 9, 10) are correct:
1. Go to P920.
2. Key in a level associated with a known volume.
3. Press ENTER .
4. Check the returned volume against the manufacturer’s chart.
5. Change parameters P054 and P055, as required.
6. Repeat steps 2 to 5 until the volume curve is verified.

Checking OCM Flow Characterization [MR 200]

To confirm universal flow calculations (P600 = 4, 5) are accurate:
1. Go to P925.
2. Enter a level with a known flow.
3. Press ENTER .
4. Check the returned flow against the manufacturer’s chart.
5. Change parameters P610 and P611, as required.
6. Repeat steps 2 to 5 until the flow curve is verified.

Page 80 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

I/O Checkout

Testing the Configuration

After the unit is installed, test to verify the wiring.

Relays

mmmmm
Use P119 to force a state change and verify that the results are as expected (pump starts,
alarm sounds, etc.).

Discrete Inputs
Use P270 to force the input value and verify that the results are as expected.
1. Go to P270 [DI] where DI = the discrete input to be tested
2. Set P270 to 0 (forced OFF)
3. Go to P275 [DI] to verify that the value is forced
4. Check the state of outputs to ensure that they respond as expected
5. Go to P270 [DI]
6. Set P270 to 1 (forced ON)
7. Go to P275 [DI] to verify that the value is forced
8. Check the state of outputs to ensure that they respond as expected
For further information see Discrete Inputs section on page 42.

mA Input [MR 200]

Use P254 to test the mA input value against a true level. Use a trusted external mA source
to generate the signal required for testing, and verify the incoming signal with P260.
Check that the system responds as expected when the mA level is changed.

mA Output
Use an external device to test the mA output against the measured level. Check that the
mA value changes to reflect the changes in the measured level.

Application Test
If you are testing the application by varying the material level (the preferred test method)
make sure that none of the control devices is connected (or at least that no power is
available to them).
If you are testing the application in simulation mode (and P000 is not –1), then control
relays are not energized and the control devices can remain connected.
While the level is being cycled, check the results of the discrete inputs either by closing
the circuit externally (preferred) or by using P270 Discrete Input Function to force the
input ON or OFF. Try all possible combinations to thoroughly test the setup. For each
combination, run a complete cycle to verify that the relays operate as expected.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 81

 Testing the Configuration Monitor system performance carefully, under all anticipated operating conditions.
1. When the MultiRanger performs exactly as required, programming is complete.
2. If alternate Reading units, Failsafe action, or relay operation is desired, update the
parameters for the new functionality.
mmmmm

3. If the system performance experiences problems, see General Appendix C:

Troubleshooting, on page 226.
If you cannot observe all possible operating conditions during the System Performance
Evaluation, use the level simulation (see page 79) to verify programming.
When a simulation is run, alarm relays will react to the simulated level changes, but
control relays will not react. You can set P000 to value –1 to trigger the control relays
based on the simulated level.
Retest the system every time you adjust any control parameters.

Page 82 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

MultiRanger Communications

MultiRanger Communication Systems

The MultiRanger is an integrated level controller capable of communicating process
information to a Supervisory Control and Data Acquisition (SCADA) system, via a serial
device such as a radio modem, leased line, or dial-up modem.
MultiRanger

Communications
mmmmm
Connection via radio modem, dial-up modem, or leased line modem

The standard MultiRanger supports the following two communication protocols:

Modbus
Modbus is an industry standard protocol used by SCADA and HMI systems. The
MultiRanger uses Modbus to communicate via the RS-485 port. For a description of the
Modbus protocol, contact your local Schneider representative.

Dolphin
Dolphin is a proprietary Milltronics protocol designed to be used with Dolphin Plus. For
more information on Dolphin Plus or to obtain a copy of the software, please go to
[Link] to contact your Siemens Milltronics representative.

Optional SmartLinx®Cards
The standard MultiRanger unit may also be enhanced with Milltronics SmartLinx®
communication modules that provide an interface to popular industrial communication
systems.
This manual only describes the built-in communications. For more information on
SmartLinx, please consult the appropriate SmartLinx manual.

7ML19981FB02 MultiRanger - INSTRUCTION MANUAL Page 83

 Communication Systems
The MultiRanger is capable of communicating with most SCADA systems, PLCs, and PCs.
The supported protocols are:
• Modbus RTU/ASCII – base unit on RS-232 or RS-485 transport
• Profibus-DP – optional SmartLinx® module
• Remote I/O – optional SmartLinx module
• DeviceNet – optional SmartLinx module

Communication Ports
Communications

The MultiRanger comes with two communication ports on the base unit.
mmmmm

Port Connection Location Interface

1 RJ-11 connector inside enclosure on main board RS-232
2 terminal block terminal block RS-485

RS-232
The RJ-11 jack connects to a laptop computer for the following:
• initial setup
• configuration
• troubleshooting
• periodic maintenance

RS-485
The RS-485 port on the terminal blocks connects into industrial communications wiring
and has the following advantages:
• runs communications cable farther
• allows multiple slave units on the network, addressed by P771 – Network Address
To communicate with equipment requiring RS-485 capability, Siemens Milltronics offers
the RS-485 External Modem Kit. For more information, go to
[Link].

Modbus
The Modbus protocol is supported in the base unit and can be configured using the
Communications parameters P770 to P782.
To set up communications with a Modbus RTU master device on port 2 using RS-485, set
the following parameters:

Page 84 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Parameter Index Value Description
P770 2 3 Modbus RTU slave
P771 2 1 Network address, only used for RS-485
P772 2 9.6 Data rate of 9600 baud
P773 2 0 No parity, common setting
P774 2 8 8 data bits, common setting
P775 2 1 1 stop bit, common setting
P778 2 0 No modem connected
P782 2 0 Index parameter values globally

Communications
SmartLinx

mmmmm
Other protocols are available through optional SmartLinx communications modules.
Details on how to install and program these modules are contained in the SmartLinx
documentation.

Dolphin Plus
Dolphin Plus software makes it easy to record and compare parameter sets for all the
MultiRangers in your company. Dolphin Plus uses a proprietary protocol called Dolphin to
communicate with Milltronics instruments. This protocol is set when P770 = 1.
By default the settings for port 1 (RJ-11 connection) and Dolphin Plus match. These
settings are:

Parameter Index Value Description

P700 1 1 Dolphin
P772 1 115.2 Data rate of 115.2 Kilo baud
P773 1 0 No parity, common setting
P774 1 8 8 data bits, common setting
P775 1 1 1 stop bit, common setting

7ML19981FB02 MultiRanger - INSTRUCTION MANUAL Page 85

 Communications Installation

Wiring Guidelines
• the RJ-11 cable maximum length is 3 meters
• RS-485 maximum length is 1,200 meters (4,000 feet)
• use 24 AWG (minimum)
• use good quality communication grade (shielded twisted pairs) cable that is
recommended for RS-485 for port 2 (Belden 9842)
• run the communication cable separately from power and control cables (do not tie
wrap your RS-232 or RS-485 cable to the power cable or have them in the same
conduit)
• use shielded cable and connect to ground at one end only
• follow proper grounding guidelines for all devices on the bus
•

Note: Improper wiring and incorrect choice of cables are two of the most common
causes of communication problems.

Ports 1 and 2
Comms Installation

Port Wall Mount

1 RS-232 port (RJ-11 modular telephone jack) is on the motherboard and
mmmmm

is generally used with a laptop computer or modem.

2 Connections for the RS-485 port are on the terminal block.

Ports 1 and 2: RS-232 RJ-11 Jack and RS-485 Locations

The RJ-11 jack and the RS-485 port are inside the enclosure of the unit.

RJ-11 Jack
TB1

TB2
L2/N L1
2
TB3
SYNC
1

mA INPUT

SHIELD

RELAY 1
1
4 - 20 mA
OUTPUTS
RELAY 2
2

RELAY 3
TS-3

SHIELD
1
RELAY 4
DISCRETE 2
INPUTS
RELAY 5

RELAY 6 RS485
COM

A
RS-485 Port
B

Page 86 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Port 1: RS-232 RJ-11 Jack
To connect the unit to a PC using an RS-232 jack, use the cable as shown:
Computer DB-9 (male)
RJ-11
6 1
to DB 9 converter
4
2 Tx Rx 2
6
RJ-11 on 3 Rx
4 SG
Tx 3
SG 5 7
8
MultiRanger RJ-11 jack
6 1 6 1
5 2
4 3
3 4
1 2 5 6
1
1
6
6
6

Modular cable with RJ-11 plug

Note: Jumper pins 4-6 and 7-8 at the DB-9.

To connect the unit to a modem using an RS-232 jack:

MultiRanger
Terminal Block
DB 9 DB 9

Comms Installation
5 5 Converter: COM
Modem RS-232 to
2 Rx 3 A
RS-485

mmmmm
3 Tx 2 B

Port 2: RS-485
MultiRanger
Terminal Block

(Shield to be grounded at one end)

C A B
O
M

To connect the unit to a modem using an RS-485 port:

COM
MultiRanger
Modem A Terminal Block
B

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 87

 Configuring Communication Ports (Parameters)
The 11 parameters listed are indexed to the two communication ports, unless otherwise
noted: An asterisk (*) identifies the preset value.

Port Description
1 RS-232 port (RJ-11 modular telephone)
2 The RS-485 port is on the terminal blocks

P770 Port Protocol

The communications protocol used between the MultiRanger and other devices.

Primary Index Communications Port

0 Communications port disabled
1 * Milltronics Dolphin protocol (preset for port 1)
Values
2 Modbus ASCII slave serial protocol
3 * Modbus RTU slave serial protocol (preset for port 2)

The MultiRanger supports the Milltronics Dolphin format ([Link]),

and the internationally recognized Modbus standard in both ASCII and RTU formats.
Other protocols are available with optional SmartLinx cards.
Comms Installation

P771 Network Address

mmmmm

The unique identifier of the MultiRanger on the network.

Primary Index Communications Port

Values Range: 0 to 9999
1 * Preset

For devices connected with the Milltronics protocol, this parameter is ignored. For
devices connected with a serial Modbus slave protocol, this parameter is a number from
1-247. The network administrator must ensure that all devices on the network have
unique addresses. Do not use the value 0 for Modbus communications as this is the
broadcast address and is inappropriate for a slave device.

P772 Baud Rate

The communication rate with the master device.

Primary Index Communications Port

4.8 4800 baud
Values 9.6 9600 baud
19.2 * 19,200 baud (preset for port 2)
115.2 * 115,200 baud (preset for port 1)

Page 88 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 This specifies the rate of communication in Kbaud. Any value may be entered, but the
only values supported are those shown above. The baud rate should reflect the speed of
the connected hardware and protocol used.

P773 Parity
The serial port parity.

Primary Index Communications Port

0 * No Parity
Values 1 Odd Parity
2 Even Parity

Ensure that the communications parameters are identical between the MultiRanger and
all connected devices, as many modems default to N-8-1.

P774 Data Bits

The number of data bits per character.

Primary Index Communications Port

Range: 5 to 8

Comms Installation
8 * Modbus RTU
Values
7 or 8 Modbus ASCII
7 or 8 Dolphin Plus

mmmmm
P775 Stop Bits
The number of bits between the data bits.

Primary Index Communications Port

Values Range: 1 or 2
1 * Preset

P778 Modem Available

Sets the MultiRanger to use an external modem.

Primary Index Communications Port

0 * No modem connected
Values 1 Answer only

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 89

 P779 Modem Inactivity Timeout
Sets the time that the unit will keep the modem connected with no activity.

Primary Index Communications Port

Values Range: 0-9999 seconds
0 * No timeout

To use this parameter, ensure that P778 (Modem Available) =1. Ensure that the value is
low enough to avoid unnecessary delays when an unexpected disconnect occurs but
long enough to avoid timeout while you are still legitimately connected. This parameter
value is ignored by the Modbus Master Drivers as they automatically disconnect when
done communicating.

Hanging Up
If the line is idle and the P779 Modem Inactivity Timeout expires, then the modem is
directed to hang up the line. Ensure that P779 is set longer than the standard polling time
of the connected master device. Set P779 to 0 to disable the inactivity timer.

P782 Parameter Index Location

Determines where index information is stored for the parameter access area for the
Comms Installation

Modbus register map.

Primary Index Global

mmmmm

Values 0 * Global
1 Parameter-Specific

For more on Parameter Index Location, see Parameter Access on page 96.

Page 90 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Modbus Register Map
Features affecting volume, mA input, and Average or Difference readings apply to the
MultiRanger 200 only. They are clearly marked.
The memory map of the MultiRanger occupies the Modbus holding registers (R40,001 and
up). This map is used when the protocol is Modbus RTU slave or Modbus ASCII slave.

Register Map for Most Common Data

Legend
Type The type of data held in the group of registers.
Start The first register to hold the referenced data.
Data Type The possible values of the data in the register. See Data Types on page
101 for more information.
Description The type of data held in the individual registers.
#R The number of registers used for the referenced data.
Read/Write Indicates whether the register is readable, writeable or both.

Read/
Type Description Start #R 1 Data Type
Write
Word Order 40,062 0/1 R/W
Map ID Register Map Type 40,063 1 0/1 = P782 R/W
ID Milltronics Product 40,064 1 4 = Model 200 R
Code 6 = Model 100
Single Parameter Access (SPA) R40,090 7 see Appendix A on page 109
Point Reading (3)2 41,010 2 -20,000 to 20,000 R
Data
Volume (2)3[MR 200] 41,020 2 -20,000 to 20,000 R

1. Modbus Register Types

Maximum registers shown; fewer may be used depending on options installed.
2.
Varies according to model. mmmmm

MR 100: Available as reading 1 and reading 2 when in either Standard or Dual Point
Mode. In Dual Point Mode, reading 1 and reading 2 are always available.
MR 200: Available as reading 1, reading 2, and Average or Difference when in either
Standard or Dual Point Mode. In Standard Mode, point 2 and 3 are only available if
P001 = Average or Difference. In Dual Point Mode, reading 1 and reading 2 are always
available. Point 3 is only available if P001[3]= Average or Difference.
3. 2nd volume available in Dual Point Mode only.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 91

 Read/
Type Description Start #R 1 Data Type
Write
Point Temperature (2) 41,030 –50 to 150 R
2
Data
Discrete Inputs (2) 41,070 1 Bit Mapped R
Relay Outputs (3 or 41,080 Bit Mapped R/W
I/O 1
6)
mA Input (1) 41,090 0000 to R
1
[MR 200] 20,000
mA Output (2) 41,110 0000 to R/W
2
20,000
Pump on Setpoint (3 41,420 0000 to R/W
6
or 6) 10,000
Pump off Setpoint (3 41,430 0000 to R/W
Pump 6
or 6) 10,000
Control
Pumped Volume (2) 41,440 UINT32 R
4
[MR 200]
Pump Hours (3 or 6) 41,450 12 UINT32 R
Pump Starts (3 or 6) 41,470 0000 to R
6
10,000
Parameter Access 43,998 to 46999 R/W
1. Maximum registers shown; fewer may be used depending on options installed.

The MultiRanger was designed to make it easy for master devices to get useful
information via Modbus. This chart gives an overview of the different sections. A more
detailed explanation of each section follows below.

Word Order (R40,062)

Modbus Register Types

This determines the format of unsigned, double-register integers (UINT32).

• 0 indicates that the most significant word (MSW) is given first
mmmmm

• 1 indicates that the least significant word (LSW) is given first

See Unsigned Double Precision Integer (UINT32) on page 101 for more information.

Note: Additional information is available from our Web site at [Link]-

[Link]

Map ID (R40,063)
This value identifies the register map used by the MultiRanger. See P782 Parameter Index
Location on page 90.
See also Parameter Access (R43,998 – R46,999) on page 96 for details.

Page 92 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Product ID (R40,064)
This value identifies the Siemens device type:

Device Type Value

MultiRanger 100 6
MultiRanger 200 4

Point Data (R41,010 – R41,031)

Measurement point data contain the current instrument readings. These are the values
shown for the reading measurement for each measurement point. The reading is based
on the setting for P001 (operation). P001 can be set to level, distance, OCM flow, or
volume. See Parameter Reference section on page 113 for details.

The measurement registers are 41,010 to 41,012. The MultiRanger uses 41,010 when
configured with a single transducer and 41,010 to 41,012 when configured with two
transducers (P111=4 or 5 only). Two transducers can create three readings because they
can generate an average or differential reading (R41,012) as well as the two level
readings (R41,010 and R41,011).

Available registers:
Data Registers Parameter
Reading 41,010 to 41,012 P920
Volume [MR 200] 41,020, 41,021 P924
Temperature 41,030 and 41,031 P912

The reading is expressed as a percentage of full scale, multiplied by 100:

Modbus Register Types

Reading Value
0 0.00%
5000 50.00% mmmmm

7564 75.64%
20,000 200.00%

Input/Output (R41,070 – R41,143)

The MultiRanger has discrete inputs, mA inputs, mA outputs and relay outputs. See
below for details for each I/O type.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 93

 Discrete Inputs (R41,070)
This table shows the current status of the discrete inputs. Only register 41,070 is used.

Discrete Input Data Address

1 41,070, bit 1
2 41,070, bit 2

Relay Outputs (R41,080)

This table shows the current status of the relays. A reading of 0 means that the relay
function is not asserted and a 1 means that it is asserted. For example, a 1 for a pump
relay means that the pump is running.

Relay Data Address

1 41,080, bit 1
2 41,080, bit 2
3 41,080, bit 3
4 41,080, bit 4
5 41,080, bit 5
6 41,080, bit 6

Values are written to control a relay only if the Relay Control Function (P111) is set to
communications (65). See Relay Function Codes (P111 Only) on page 104.

mA Input (R41,090) [MR 200]

The mA input is scaled from 0 to 2,000 (0 to 20 mA multiplied by 100). P254 displays the
value of the input. This parameter is indexed by the input number.
Modbus Register Types

mA Output (R41,110-41,111)
The mA output is scaled from 0 to 2,000 (0 to 20 mA multiplied by 100). This is displayed in
P911.
mmmmm

Pump Control (R41,400 – R41,474)

Only relays set for pump control (P111 = 50 to 52) are available. These registers have no
effect on relays programmed for other uses.

Pump ON Setpoint (R41,420 – R41,425)

The ON setpoint level (P112) for the referenced pump relay.
The setpoint is scaled from 0 to 10,000 (0 to 100% of span multiplied by 100). So 54.02% is
shown in the register as 5402.

Page 94 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Pump OFF Setpoint (R41,430 – R41,435)
The OFF setpoint level (P113) for the referenced pump relay.
The setpoint is scaled from 0 to 10,000 (0 to 100% of span multiplied by 100). So 54.02% is
shown in the register as 5402.

Pumped Volume (R41,440 – R41,443) [MR 200]

The pumped volume registers hold the current total for all of the pumps associated
with a level point. These registers are available only if operation is set to pumped
volume (P001 = 7).
These volumes can become very large. Therefore, two registers are used to hold the
value. See Unsigned Double Precision Integer (UINT32) on page 101 for more information.
The value in the registers is given as an integer value but must be interpreted as having
the number of decimals set in P633 (LCD Totalized Decimal Position): this number can be 0
to 3. Ensure that your software accounts for these decimal places before you report the
pumped volume totals.

Pump Hours (R41,450 – R41,461)

The number of running hours for the referenced pump relay. The hours are given to three
decimal places, so the integer must be divided by 1000 to get the correct value. For
example 12,340 represents 12.34 hours.
This value comes from parameter P310. See page 153 of the Parameter Reference section
for details.

Pump Starts (R41,470 – R41,475)

The number of pump starts for the referenced pump relay.
This value comes from parameter P311. See page 153 of the Parameter Reference section Modbus Register Types
for details.
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 95

 Parameter Access (R43,998 – R46,999)
Parameter values are given as integers in the range of registers from R44,000 to R44,999.
The last three numbers of the register correspond to the parameter number.

Parameter Register # Format Register # Parameter #

44,000 46,000 P000
44,001 46,001 P001
44,002 46002 P002
… … …
44,999 46,999 P999

Usually, the parameters are all read / write.

Note:
• Parameters P000 and P999 are read only. If P000 is set to lock activated then all of
the parameters are read only
• Parameter P999 (Master Reset) cannot be used via Modbus
• See Data Types on page 101 for a description of the different types of data
associated with different parameters

Each parameter register has a corresponding format register that holds the format
information required to interpret the value. See Format Words (R46,000 to R46,999) on
page 99.

Parameter Indexing
Many parameters are indexed. There are two possible indexes: a primary index and a
secondary index. A secondary index is a sub-address of the primary index. Some indexed
parameters affect multiple I/O devices.
Modbus Register Types

The following is an example of a primary index:

P111 is the Relay Control Function. This parameter determines how a relay is controlled
by the MultiRanger (used as an alarm, for pump control, etc.). Because there are up to six
mmmmm

relays on the MultiRanger, P111 is indexed by six to allow each relay to be programmed
independently.
A few parameters also have a secondary index. While a secondary index is important for
setting up the MultiRanger, it is almost never needed through remote communications.

Indexing the Parameter Access Area

Each parameter communicates its value to only one register. You must know the index(es)
for the parameter in order to interpret the information in the register correctly.
For example, to make use of the value returned in register R44,111 you must know which
relay it is referring to. See Relay Function Codes (P111 Only) on page 104 for details on
P111 values.

Page 96 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 To determine the index values, the primary and secondary index must be read or write.
The two possible methods of handling these index values are described in the following
paragraphs: Global Index Method and Parameter Specific Index Method.

Reading Parameters
To read parameter values, follow the steps listed in either the Global or the Parameter
Specific Index Method that follow. You must be able to program your HMI or SCADA
system before completing these methods.

Global Index Method (P782 = 0)

Global format method sets index values for all parameters simultaneously. Use this
method to read multiple values set to the same index values.
1. Write the primary index value into R43,999.
This is a value between 0 and 40 which specifies the input or output indexed by the
parameter.

Examples are:
• Transducer 1 is index 1
• Discrete input 2 is index 2
• Relay 5 is index 5
2. Write the secondary index value into R43,998.
This is a value between 0 and 40 that specifies the secondary index on the
parameter. This value is usually 0.
3. Write the desired format value into the appropriate format register. Because the
primary and secondary indexes are already specified, these portions of the format
word are ignored and only the last digit is significant.
See Format Registers on page 110 for details.

Modbus Register Types

4. Read the value from the appropriate parameter register.

Types of values are:

mmmmm

• Numeric Values, on page 101

• Bit Values, on page 101
• Split Values, on page 102
• Text Messages, on page 103
• Relay Function Codes (P111 Only), on page 104
A value of 22,222 indicates that an error has occurred. Specify a different format
type and try again.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 97

 Parameter Specific Index Method (P782 = 1)
The Parameter Specific index method sets the index values for each parameter
independently. Use this method to read multiple parameters with different index values.
1. Write the primary index, secondary index, and data format values into the
appropriate format register.
For example, to read the following information:
• measured level (P921)
• in units with three decimal places
• from Transducer One
Send the integer value 01008 to register 46,921.
2. Read the value from the appropriate parameter register (the example uses 44,921).
Types of values are:
• Numeric Values on page 101
• Bit Values on page 101
• Split Values on page 102
• Text Messages on page 103
• Relay Function Codes (P111 Only) on page 104
A value of 22,222 indicates that an error occurred. Specify a different format type
and try again.

Writing Parameters
The method of writing parameters is similar to the method of reading them. Become
familiar with Reading Parameters, page 97, before attempting to write any parameters.
To write parameter values to the MultiRanger, follow these steps:

Global Index Method (P782 = 0)

1. Write the primary index value into R43,999.
Modbus Register Types

2. Write the secondary index value into R43,998.

3. Write the desired format value into the appropriate format register.
mmmmm

4. Write the value to the appropriate parameter register.

Parameter Specific Index Method (P782 = 1)

1. Write the primary index, secondary index, and data format values into the
appropriate format register.
2. Write the value to the appropriate parameter register.

Page 98 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Format Words (R46,000 to R46,999)
Format words are unsigned integers that contain up to three values (described below).
The number of values used in the format words depends on the Parameter Index Location
(P782) that is used.
Parameter P782 Parameter Index Location, described on page 90, determines which of
two methods is used to access the format words: Global Index Method or Parameter
Specific Index Method.

Global Index Method (P782 = 0)

Only the final digit of the format word determines the decimal offset (below).

Parameter-Specific Index Method (P782 = 1)

All three decimal fields are used to determine the parameter value’s primary index,
secondary index, and decimal offset.

Format Registers
Each format register is made up of three decimal fields:
• decimal offset
• secondary index
• primary index

decimal offset (0-9)

Modbus Register Types

secondary index (00-99)

primary index (00-64)

mmmmm

The primary and secondary indices correspond to those that are used by the parameter.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 99

 The decimal offset indicates how the remote system must interpret the integer value that
is stored in the parameter access register. The following table shows how different
parameter values can be shown based on a register value (integer) of 1234.

Decimal Offset Example

0 0 1,234
1 –1 12,340
2 –2 123,400
3 –3 1,234,000
4 –4 12,340,000
5 –5 123,400,000
6 +1 123.4
7 +2 12.34
8 +3 1.234
9 Percent 12.34%

Examples of using the format word for both the index values and the decimal offset value
are shown below:

Format Primary Index Secondary Index Decimal

00000 00 00 0
01003 01 00 3 right
02038 02 03 3 left
05159 05 15 percent

To write these values you can use a decimal offset as follows: format word = (primary
index x 1000) + (secondary index x 10) + (decimal).
Modbus Register Types
mmmmm

Page 100 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Data Types
The MultiRanger parameters do not always use integers to hold values. For the
convenience of the programmer, those values are converted to and from a 16-bit integer
number. This section describes the conversion process. The sections that follow describe
where those values are in the discrete I/O and block transfer addresses, and how to get
the parameters you need.

Numeric Values
Numeric parameter values are the most common. For example, parameter P920
(Reading) returns a number that represents the current reading (either level or volume,
depending on the MultiRanger configuration).
Numeric values are requested or set in units or percent of span, and may be specified
with a number of decimal places.
Numeric values must be in the range –20,000 to +20,000 to be valid. If a parameter is
requested and its value is more than +20,000, the number 32,767 is returned; if it is less
than –20,000, the number –32,768 is returned. If this overflow happens, decrease the
number of decimal places.
If a parameter cannot be expressed in terms of percent of span, or has no meaningful
value, the number 22,222 is returned. Try requesting the parameter in units, or refer to
P005 in the Parameter Reference section on page 118.

Bit Values
Bits are packed into registers in groups of 16 bits (1 word). In this manual, the bits are
numbered from 1 to 16, with bit 1 as the least significant bit (LSB) and bit 16 as the most
significant bit (MSB).

16 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01
MSB LSB

Unsigned Double Precision Integer (UINT32)

Large numbers are put into unsigned 32 bit integers. By default, they are set up so that
the first word (register) is the most significant word (MSW) and the second word
(register) is the least significant word (LSW).
Data Types
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 101

 For example, if R41,442 is read as a UINT32, the 32 bits would look like this:

R41,442 R41,443
16 MSW 1 16 LSW 1
32 32-bit integer value (UINT32) 1

The two registers are read as a 32-bit integer.

The most significant word (MSW) and least significant word (LSW) can be reversed to
accommodate some Modbus drivers. See Word Order (R40,062) on page 92 for details.
The position of the decimal place is dependent on the register. For more details see the
description of the register.

Split Values
Certain parameters are actually a pair of numbers separated by a colon, using this
format: xx:yy.

One example is P807, Transducer Noise, where:

xx = the average noise value in dB
yy = the peak noise in dB
The number which corresponds to xx:yy, either for reading or setting a parameter, is
determined by the following formula:
For storing to the device:
value = (xx + 128) x 256 + (yy + 128)
For reading from the device:
xx = (value / 256) – 128
yy = (value % 256) – 128
where % is the modulus operator.
The modulus can be computed by following these steps:
value1 = value / 256
value2 = remainder of value1
value3 = value2 x 256
yy = value3 – 128

It may simplify Parameter to notice:

xx = (most significant byte of value) – 128
yy = (least significant byte of value) – 128
Data Types
mmmmm

Page 102 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Text Messages
If a device parameter returns a text message, that message is converted to an integer
and provided in the register. The numbers are shown in the following table:

Number Text Message as displayed on LCD

22222 Invalid value
30000 Off
30001 On
30002 ≡≡≡≡
30003 (parameter does not exist)
30004 Err
30005 Err1
30006 Open
30007 Short
30008 Pass
30009 Fail
30010 Hold
30011 Lo
30012 Hi
30013 De
30014 En
30015 ---- (parameter has not been set)
-32768 Value is less than –20,000
32767 Value is greater than 20,000

Data Types
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 103

 Relay Function Codes (P111 Only)
Please note that the MultiRanger 200 offers more function codes.
If a device parameter returns a relay function code, that message is converted to a
number and is then provided in the register. The numbers are shown in the following
table:

MultiRanger 100
Relay Function Code Number P111
OFF, relay not used 0 0
Undesignated Level Alarm 1 1
Low-Low Level Alarm 2 1 – LL
Low Level Alarm 3 1–L
High Level Alarm 4 1–H
High-High Level Alarm 5 1 – HH
Loss of Echo (LOE) Alarm 20 6
Transducer Cable Fault Alarm 16 7
Fixed Duty Assist 25 50
Alternate Duty Assist 30 52
Communication 66 65

MultiRanger 200
Relay Function Code Number P111
OFF, relay not used 0 0
Undesignated Level Alarm 1 1
Low-Low Level Alarm 2 1 – LL
Low Level Alarm 3 1–L
High Level Alarm 4 1–H
High-High Level Alarm 5 1 – HH
In Bounds Alarm 6 2
Out of Bounds Alarm 9 3
Rate of Level Change Alarm 12 4
Temperature Alarm 15 5
Loss of Echo (LOE) Alarm 20 6
Transducer Cable Fault Alarm 16 7
Totalizer 22 40
Flow Sampler 23 41
Data Types

Fixed Duty Assist 25 50

mmmmm

Fixed Duty Backup 26 51

Alternate Duty Assist 30 52

Page 104 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Relay Function Code Number P111
Alternate Duty Backup [MR 200] 31 53
Service Ratio Duty Assist [MR 200] 35 54
Service Ratio Duty Backup [MR 200] 36 55
First In First Out (FIFO) [MR 200] 40 56
Flush Valve [MR 200] 65 64
Communication 66 65

See P111 on page 130 of theParameter Reference section.

Data Types
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 105

 Error Handling Error Handling

Modbus Responses
mmmmm

When polled by a Modbus Master, a slave device will do one of the following:
1. Not reply. This means that something went wrong with the transmission of the
message.
2. Echo back the command with the correct response (see the Modbus specification
for more details). This is the normal response.
3. Return an Exception Code. This reflects an error in the message.

MultiRanger uses the following exception codes:

Code Name Meaning
01 Illegal Function The function code received in the query is
not an allowable action for the slave.
02 Illegal Data Address The data address received in the query is
not an allowable address for the slave.
03 Illegal Data Value A value contained in the query data field
is not an allowable value for the slave.

Error Handling
Errors can be traced to two general sources:
1. There is an error in transmission.
OR
2. The host tries to do something that is not a valid action.
In the first case, the MultiRanger does not respond and the master waits for a response
time out error, which causes the master to re-send the message.
In the second case, the response depends on what the host tries to do. In general,
MultiRanger will not give an error to the host request. Various actions and the expected
outcome are as follows:
• If the host reads an invalid register, the host will get an undetermined value back.
• If the host writes an invalid register (a non-existing parameter or a read only
parameter), the value will be ignored and no error response will be made. However,
the current value will not reflect the desired new value.
• If the host writes a read only register, then the value will be ignored and no error
response will be made. However, the current value will not reflect the desired new
value.

Page 106 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 • If P000 is activated, then the value will be ignored and no error response will be
made. However, the current value will not reflect the desired new value.
• If the host attempts to write one or more registers that are out of range, an

Error Handling
exception response code 2 or 3 is generated, depending if the start address is valid.

mmmmm
• If the host used an unsupported function code, an exception response code of 01
should be generated. However, this is not guaranteed and there may be no
response.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 107

 Error Handling Communication Troubleshooting

Generally
mmmmm

1. Check the following:

• There is power at the unit
• The LCD is showing the relevant data
• The device can be programmed using the hand programmer
2. Check the wiring pin outs and verify that the connection is correct.
3. Verify that values in the set-up parameters (P770 to P779) match the settings in the
computer used to communicate with the unit.
4. Check that the port on the computer is correct. Sometimes trying a different Modbus
driver will solve the problem. An easy stand-alone driver called ModScan32 is
available from Win-Tech at [Link]. This driver is helpful for testing
communications.

Specifically
1. The MultiRanger is set to communicate via a modem but no communication is
returning to the master.
• Check that the parameters are set up correctly and that the correct port is
configured
• Verify the wiring diagram. Note that there is a difference between wiring directly
to a computer and wiring to a modem. Verify that the modem is set up correctly.
Siemens Milltronics has a series of Application Guides that may help. Please
contact your local Siemens Milltronics representative for more information on
Application Guides.
2. A MultiRanger parameter is set via remote communications, but the parameter
remains unchanged.
• Some parameters can only be changed when the device is not scanning. Try
putting the device in program mode, using the operating mode function.
• Try setting the parameter from the keypad. If it can not be set using the keypad,
check the lock parameter and set it to 1954.

Page 108 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Communication Appendix A: Single
Parameter Access (SPA)
This Appendix is intended to provide someone with advanced communications
knowledge the ability to access any parameter value in any available format.
Built into MultiRanger is an advanced handshaking area that can be used to read and
write single registers to the MultiRanger. This section performs a similar function to the
Parameter access section. The differences are:
1. Advanced section is more powerful and harder to program.
2. Advanced section only gives you access to one parameter at a time.

Mapping
Parameter Read and Write (40,090 – 40,097) is a series of eight registers used for reading
and writing parameter values to and from the MultiRanger. The first three registers are
always unsigned integers representing parameters and index values. The second five
registers are the format and value(s) of the parameter.

Communication Appendix A
All parameters normally accessed through the hand-held programmer are available
through these registers.

Address Description

mmmmm
40,090 Parameter (integer)
40,091 Primary Index (integer)
40,092 Secondary Index (integer)
40,093 Format word (bit mapped)
40,094 Read value, word 1
40,095 Read value, word 2
40,096 Write value, word 1
40,097 Write value, word 2

Reading Parameters
To read parameters through Modbus do the following steps:
1. Send the parameter, its primary index, and its secondary index (usually 0), and
format to registers 40,090 to 40,093.
2. Wait until you can read the written values from the registers (40,090 to 40,093) to
confirm that the operation is complete.
3. Read the value from registers 40,094 and 40,095.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 109

 Writing Parameters
To set parameters through Modbus do the following steps:
1. Send the parameter, its primary index, and its secondary index (usually 0) to
registers 40,090, 40,091, and 40,092.
2. Write the value to registers 40,096 and 40,097.
3. Write the desired format word to register 40,093 to enable the MultiRanger to
interpret the value correctly.

Format Register
Bits Values Description
1-8 0-2 Error Code
9-11 0-7 3-bit number representing decimal offset
12 0/1 direction of offset (0 = right, 1 = left)
13 0/1 Numeric format: Fixed (0) or Float (1)
14 0/1 Read or Write of data, Read (0), Write (1)
Communication Appendix A

15 0/1 Word order: Most Significant Word first (0), Least

Significant Word first (1)
16 Reserved

For example, to format the level reading so that it is shown in percent with two decimal
mmmmm

places shifted left, the format bits would look like this:

Bit
16 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01
Numbers
Bit Values 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
offset direction to right
most significant first

decimal offset of 2

no error code
fixed format
reserved

read

The value sent to the MultiRanger is 0001001000000000 binary or 512 decimal. The value
512 is sent as an integer to register 40,093 to format the output words 40,094 and 40,095
accordingly.
If the numeric data type is set for integer and the value contains decimal places, they are
ignored. In this situation, use the decimal offset to ensure that you have an integer value
and then write your code to recognize and handle the decimal offset.

Page 110 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Error Codes
The error codes returned in the format area are 8-bit integers found in the lowest eight
bits of the format word. This allows for 256 potential error codes.
Currently the MultiRanger has two error codes available.

Values Description
0 No error
1 Data not available as percent (available as units)
2-255 Reserved

Communication Appendix A
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 111

 Communication Appendix A Notes
mmmmm

Page 112 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Parameter Reference
The MultiRanger is configured through its parameters, and the application determines
the parameter values which are entered into the unit.
Please check your value entries carefully before operating the MultiRanger to ensure
optimum performance.

MultiRanger 100 and MultiRanger 200

All MultiRanger 100 and MultiRanger 200 parameters are listed in this section.
MultiRanger 200 parameters are identified separately. The parameter title includes this
marking [MR 200], indicating that parameter applies to the MultiRanger 200 only.
As a general rule, parameters affecting volume apply only to the MultiRanger 200.

Helpful Hints
Please note the following:
• Default values are always indicated with an asterix (*)
• Global values are common for all inputs and outputs on the unit
• Indexed parameters can apply to more than one input or output
• Primary index relates to an input or output
• Secondary index allows for multiple values on an indexed point

Accessing a Secondary Index

1. Press MODE , and then press DISPLAY to activate secondary index.

The icon appears under the index field.
2. Enter the secondary index, and then enter the values to set the secondary index.

Parameters
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 113

 Parameters Notes
mmmmm

Page 114 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P000 Lock
Secures the MultiRanger from changes.
Primary Index Global
1954 * OFF (programming permitted)
Simulation Controls (relays energize based on simu-
Values -1
lated level)
other lock activated (programming secured)
Related • Simulation on page 79

WARNING:
Use this lock as backup security only. It uses a fixed value which can be
discovered by unauthorized personnel.
Access this parameter directly (type 000) and enter any value (except 1954) to secure
programming lock. To unlock the MultiRanger, access this parameter and enter 1954.

Quick Start (P001 to P007)

P001 Operation
Sets the type of measurement required for the application.
Standard Mode Dual Point Mode
Primary Index
Global Transducer
0 Out-of-service
1 Level – how full the vessel is (MR 200: volume – P050)
2 Space – how empty the vessel is (MR 200: ullage – P050)
3 * Distance – distance from transducer to material
Values
4 DPD – dual point difference [MR 200]
5 DPA – dual point average [MR 200] Parameters
6 OCM – flow rate in an open channel [MR 200]
7 Pump Totalizer – total pumped volume [MR 200]
mmmmm

Alters • P600 Primary Measuring Device

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 115

 For DPD and DPA Programming [MR 200]
Please note that this feature is only available on the MultiRanger 200.

Single Point Model Use

For Dual Point Difference (DPD) or Dual Point Average (DPA), the unit requires either two
transducers of the same type, or one transducer and one mA input. If two transducers are
used, all transducer parameters become indexed, and a third level point is calculated.
• DPD (difference) = Point 1 - Point 2
• DPA (average) = (Point 1 + Point 2) / 2. The calculated DPD or DPA is always based
on level measurements of points 1 and 2.
For these operations any of three level points (transducer 1, transducer 2, or the
calculated point) can be used to trigger relays (see P110 Level Source on page 130).
The points must be globally set to either 4 or 5 (as required). Point 3 becomes the
calculated value as shown above. See Rake Control example on page 63.

Dual Point Model Use

To set a dual point MultiRanger for DPA or DPD functions, Point 3 must be set to either 4
or 5 (as required). Points 1 and 2 cannot be set to 4 or 5, but these points are used to
calculate the value in point 3.
This table shows the available functions:
Operation [index] Available Values
P001 [1] 1, 2, 3, 6, 7
P001 [2] 1, 2, 3, 6, 7
P001 [3] 4,5

P002 Material
Specifies material type.
Standard Mode Dual Point Mode
Primary Index
Parameters

Global Transducer
mmmmm

1 * Liquid or horizontal solid surface

Values
2 Solid or angled surface
Alters • P830 TVT Type

Page 116 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P003 Maximum Process Speed
Determines level change reaction.
Primary Index Transducer
1 Slow (0.1 m/min)
Values 2 * Medium (1 m/min)
3 Fast (10 m/min)
• P070 Failsafe Timer
• P700 Max Fill Rate
• P701 Max Empty Rate
• P702 Filling Indicator
• P703 Emptying Indicator
Alters
• P704 Rate Filter
• P710 Fuzz Filter
• P713 Echo Lock Window
• P727 Scan Delay
• P841 Long Shot Number
• Failsafe (P070 to P072)
• P121 Pump by Rate
• Rate (P700 to P708)
Related
• Measurement Verification (P710 to P713)
• Transducer Scanning (P726 to P729)
• P905 Transmit Pulse

Use a setting just fast enough to keep up with your process. Slower settings provide
higher accuracy. Faster settings allow for more level fluctuations.

P004 Transducer
Specifies the Siemens Milltronics transducer connected to the unit.

Primary Index
Standard Mode Dual Point Mode
Global Transducer
0 * No transducer attached (preset for Dual Point)
Parameters
1 ST-25
2 ST-50
mmmmm

100 STH
101 XCT-8
Values
102 * XPS-10 (preset for Standard Mode)
103 XCT-12
104 XPS-15
112 XRS-5
250 mA input [MR 200]
• mA Input (P250 to P260)
• P842 Short Shot Frequency
• P843 Long Shot Frequency
Related
• P844 Short Shot Width
• P845 Long Shot Width
• P852 Short Shot Range

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 117

 P005 Units
Specifies measurement units used for dimensional values.
Primary Index Global
1 * Meters
2 Centimeters
Values 3 Millimeters
4 Feet
5 Inches
• P006 Empty
• P007 Span
• P060 Decimal Position
• P603 Maximum Head
Alters • P605 Zero Head
• P620 Low Flow Cutoff
• P921 Material Measurement
• P926 Head Measurement
• P927 Distance Measurement

Changing this value automatically changes the units displayed for many parameters.
Existing values are converted and do not have to be re-entered.

P006 Empty
Enter distance in units (P005) from the face of the transducer to the process empty point.
Primary Index Transducer
Range: 0.000 to 9999
Values
Preset: 5.000m (or equivalent depending on units)
Alters • P007 Span
Altered By • P005 Units
• P800 Near Blanking
Related • P921 material Measurement
• P927 Distance Measurement
Parameters

Setting this value also sets Span (P007) unless Span was already set to another value.
mmmmm

For distance operation (P001=3), Span is preset to Empty.

Page 118 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P007 Span
Sets the range levels to be measured.
Primary Index Level
Range: 0.000 to 9999
Values
Preset: based on Empty (P006)
• P605 Zero Head
Alters • P112 Relay ON Setpoint
• P113 Relay OFF Setpoint
• P005 Units
Altered By
• P006 Empty
• Volume (P050 to P055)
• P800 Near Blanking
Related • P921 Material Measurement
• P922 Space Measurement
• P926 Head Measurement

Span is preset for a value close to the maximum available. Enter a value reflecting
maximum application range.
Always prevent the monitored surface from approaching within 0.33m (1 ft) of the
transducer face as this is the minimum blanking for most Milltronics transducers (some
require more blanking – see your transducer manual).
Many other parameters are set as a percentage of span (even if they are entered in
units). The values of these other parameters may change if the span is altered after
installation and the other parameters are measured using a level determined upward
from the Empty level toward the transducer face.

MultiRanger 200
All volumes are based on span so it should be set for the maximum volume point if
volume calculations are needed.

Volume (P050 to P055) [MR 200]

Parameters
mmmmm

Please note that the volume parameters apply only to the MultiRanger 200.
Use these parameters to enable the MultiRanger to show readings based on vessel or
wet well volume (rather than level)..

P050 Tank Shape [MR 200]

Enter the Tank Shape value matching the monitored vessel or wet well.
When Operation is LEVEL (P001 = 1), liquid (material) volume is calculated.
Alternatively, when Operation is SPACE (P001 = 2), remaining vessel capacity is
calculated. In RUN mode, readings are displayed in percent of maximum volume. To
convert readings to volumetric units, see Maximum Volume (P051).

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 119

 Standard Mode Dual Point Mode
Primary Index
Global Transducer
# Shape Description
volume calculation not required
0 *
(preset)

1 Flat Level Bottom

2 Cone/Pyramid Bottom

3 Parabola Bottom

Values

4 Half Sphere Bottom

5 Flat Sloped Bottom

Parameters

6 Flat Ends
mmmmm

7 Parabola Ends

Page 120 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 8 Sphere

Values 9 Universal Linear

10 Universal Curved

• P001 Operation
• P051 Maximum Volume
Alters • Pump Efficiency (P180-P186)
• Pumped Volume Totalizer (P622-P623)
• P920 Reading Measurement

P051 Maximum Volume [MR 200]

For Readings in volumetric units (rather than percent), enter the vessel volume between
Empty (P006) and Span (P007).
Standard Mode Dual Point Mode
Primary Index
Global Transducer
Range: 0.000 to 9999
Values
Preset: 100.0
Alters P060 Decimal Position
• P006 Empty
Related • P007 Span
• P924 Volume Measurement Parameters

Any volume units can be chosen because volume is calculated from empty to maximum mmmmm

span and is scaled according to the Tank Shape (P050) value.

Note: Make sure selected chosen units allow LCD volume display.
Examples:
• If max. volume = 3650 m3, enter 3650
• If max. volume = 267500 gallons, enter 267.5 (thousands of gallons)

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 121

 P052 Tank Dimension A [MR 200]
Dimension A as used in P050 Tank Shape.
Standard Mode Dual Point Mode
Primary Index
Global Transducer
Range: 0.0 to 9999
Values
Preset: 0.000
Related • P050 Tank Shape

Enter one of the following:

• height of the tank bottom if P050 = 2,3,4, or 5
OR
• length of one end section of the tank if P050 = 7, in Units (P005)

P053 Tank Dimension L [MR 200]

Dimension L as used in P050 Tank Shape.
Standard Mode Dual Point Mode
Primary Index
Global Transducer
Range: 0.0 to 9999
Values
Preset: 0.000
Related • P050 Tank Shape

Enter the following:

• tank length (excluding both end sections) if P050 = 7

P054 Level Breakpoints (Universal Volume Calculation)

[MR 200]
Parameters

When the tank shape is too complex for any of the preconfigured shapes, you can specify
mmmmm

the volume based on segments.

Standard Mode Dual Point Mode
Primary Index
Global Transducer
Secondary Index Breakpoint
Values Range: 0.0 to 9999
Related • P055 Volume Breakpoints

Enter the following:

• up to 32 level breakpoints (where volume is known) if P050 = 9 or 10

Page 122 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Entering a Level Breakpoint
1. Go to Parameter P054.
2. For each index enter a breakpoint in measurement units.
3. Ensure that each breakpoint corresponds to the same index for P055.

P055 Volume Breakpoints and Characterization

(Universal Volume Calculation) [MR 200]
Each segment defined by the level breakpoints (P055) requires a volume so that the
MultiRanger can make the level-to-volume calculations.
Standard Mode Dual Point Mode
Primary Index
Global Transducer
Secondary Index Breakpoint
Values Range: 0.0 to 9999
Related • P054 Breakpoints Levels (Universal Volume Calculation)

Typical volume calculations

Cone Cylinder

V = (1/3)πr2h V = πr2h

Entering a Volume Breakpoint

1. Go to Parameter P055.
2. For each index enter a volume. Parameters
3. Ensure that each volume corresponds to the same index for P054.
mmmmm

For more on Volume Characterization, go to page 45.

Display and Reading (P060 to P062)

These parameters are used to:
• Change the number of decimal places displayed
• Convert the Reading to alternate units
• Reference measurements to other than Empty (P006) or Span (P007)

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 123

 P060 Decimal Position
Defines the maximum number of decimal places used on the LCD.
Primary Index Level
0 No digits after the decimal point
1 1 digit after the decimal point
Values
2 * 2 digits after the decimal point
3 3 digits after the decimal point (limited by device resolution)
Alters • P607 Flowrate Decimal
• P005 Units
Altered by
• P051 Maximum volume
Related • P920 Reading Measurement

In RUN mode, the decimal position adjusts to prevent the number of digits from exceeding
the display capabilities. To keep the decimal place from shifting, reduce the number of
decimal places to that shown at 100%.
Example:
If 100% is 15m, use two decimal places for sample readings of 15.00 or 12.15.

P061 Convert Reading [MR 200]

Multiplies the current value by the specified amount to allow for scaling.
Primary Index Level
Range: -999 to 9999
Values
Preset: 1.000
Related • P920 Reading Measurement

Examples:
• If the measured value is in feet, enter 0.3333 to display the number of yards
• For simple linear, volume conversions set POO5 to 1 (meters) and then enter the
volume measurement per unit to get the correct conversion. For example, if the
Parameters

reservoir contains 100 litres per vertical meter, use 100 to get the reading in litres.
mmmmm

Notes:
• This method does not calculate volume. It must not be used in place of the volume
parameters if any volume dependent features (such as pump efficiency) are used.
To calculate true volumes see Volume (P050 to P055).
• Avoid entering a value that, when multiplied by the maximum current Reading,
exceeds the display capabilities. If value exceeds four digits, EEEE is shown.

Page 124 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P062 Offset Reading
Adds the specified value to the level reading, usually to reference the reading to sea level
or another datum level.
Primary Index Level
Range: -999 to 9999
Values
Preset: 0.000
Related • P920 Reading Measurement

The operation of the device is not affected by the Offset Reading. This value is used for
display purposes only. All control measurements are still referenced to Empty.

Backup Level Override

Use this feature to override the ultrasonic reading by a discrete input such as a
contacting point device. The ultrasonic reading will be fixed at the programmed switch
level until the discrete input is released.
The ultrasonic device makes decisions based on the override values.

P064 Reading Override Enable

Sets the discrete input to act as the source for a level reading override.
Primary Index Transducer
0 * OFF: No override.
Values
1-2 ON: Number = discrete input of override signal
• P065 Reading Override Value
Related
• P270 Discrete Input Function

P065 Reading Override Value

Parameters
This value is substituted for the current reading when the selected discrete input is
enabled and activated.
mmmmm

Primary Index Transducer

Values Range: 0.0 to 9999
Alters Current reading
• P001 Operation
• P005 Units
Related • P006 Empty
• P007 Span
• P064 Override Enable

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 125

 Please note the following:
• enter value in current units (as selected in P005)
• valid for level, space, and distance
• volume is calculated based on the Backup level
Example:
Transducer One is configured for a level measurement. Digital Input 2 is connected to a Hi
Level Backup switch located a level of 4.3m.

Parameter Index Value

P064 1 2
P065 1 4.3

When the level rises to 4.3m, and the switch is activated, the reading is forced to 4.3m.
The reading stays at 4.3m until the switch is de-activated.

P066 Override Time Delay

Defines the time used to calm (debounce) the override condition input. Set in seconds.
Primary Index Transducer
Range: 0.0 to 9999
Values
Preset: 5.0
• P064 Override Enable
Related • P065 Reading Override Value
• P270 Discrete Input Function

Note: Activation of the Level Override is subject to the measurement cycle. This can
add up to four seconds to the overall response time depending on operating conditions
and programming.

P069 Password
Parameters

Holds the current password for P000. Select by typing in 069. You cannot scroll to this
mmmmm

parameter.
Primary Index global
Range: 0 to 9999
Values
Default: 1954
Related • P000 Lock

This parameter is write-only, and can only be selected by entering 069. To change the
password, unlock the device by entering the current password into P000. Then enter the
new password into P069. To lock the device, enter a password other than the correct one
in P000. While the device is unlocked, the password is visible in P000.

Page 126 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Failsafe (P070 to P072)
P070 Failsafe Timer
The time for invalid measurements to elapse before Failsafe State activates.
Standard Mode Dual Point Mode
Primary Index
Global Transducer
Range: 0.0 to 9999
Values
Preset 10.00 minutes
Altered by • P003 Maximum Process Speed
Related • P129 Relay Failsafe

Once activated, the Failsafe State initiates the following:

1. The material level is reported based on P071 Failsafe Material Level.
• The unit responds to the new level as programmed (control and alarm relays
activate as defined by the programming).
• Individual relays can have independent failsafe responses. See P129 Relay
Failsafe.
2. The appropriate error is displayed:
• LOE for loss of echo from the transducer
• Short for a shorted transducer cable
• Open for a cut transducer cable
• Error for all other problems
When modifying the preset value, set it short enough to protect the process but long
enough to avoid false alarms. Only use No Delay (0.0 Minutes) for testing.

P071 Failsafe Material Level

The material level reported when a Failsafe State is initiated.
Primary Index Level Point
Parameters
Range: -4999 Value in units or % (-50% to 150% of span) mmmmm

to 9999
Values HI Level goes to maximum span
LO Level goes to 0 span (Empty)
HOLd * Level remains at last reading
• P001 Operation
• P006 Empty
• P007 Span
Related • P111 Relay Control Function
• P112 Relay ON Setpoint
• P113 relay OFF Setpoint
• P129 Relay Failsafe

Select the Failsafe Material Level based upon the relay operation required during failsafe
operation.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 127

 Selecting HI, LO, or HOLd
1. Press FUNCTION to display the Auxiliary Function symbol.
2. Press ARROWS to scroll to the desired option.
3. Press ENTER to set the value.

Entering a Measurement
To enter a specific Failsafe Material Level within -50 to 150% of Span (P007), in Units
(P005).

Relay reaction
The way in which relay programming reacts to the failsafe level depends on P129 Relay
Failsafe (page 136). By default:
• Alarm relays have P129 = OFF and so react to the Failsafe Material Level.
• Control relays have P129 = dE and so de-energize the relay when the unit enters
Failsafe mode regardless of the Failsafe Material Level.

P072 Failsafe Level Advance

Sets the speed the MultiRanger advances to and returns from the Failsafe Material Level.
Primary Index Level Point
Advances to/from Failsafe Material Level as set by
1 * Restricted
P003, P700 and P701.
Values 2 Immediate Failsafe Material Level assumed right away
Failsafe Level Advance is restricted, return is
3 Fast Back
immediate
• P003 Maximum Process Speed
• P070 Failsafe Timer
Related • P071 Failsafe Material Level
• P700 Max Fill rate
• P701 Max Empty rate
Parameters

Relays (P100 to P119)

mmmmm

The MultiRanger has three or six relays (or digital outputs) used to control devices and
alarms. While the number of devices is limited by the relays, all control functions are
accessible through software and each parameter is indexed to the three or six relays.
See the Relay section on page 35.

Preset Applications (P100)

The MultiRanger makes standard applications easier to program by providing an
extensive list of presets.

Control Functions (P111)

Page 128 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Each relay can be configured independently to take advantage of the MultiRanger’s
advanced features and flexibility. Start with a preset application and then change the
required parameters to make the task more efficient.

Setpoints (P112, P113)

Each relay is triggered by one or more setpoints. The setpoints can be based on absolute
level (P112, P113) or rate of change (P702, P703). Each control function specifies which
setpoints are required.

P100 Preset Applications [MR 200]

Six preset applications to configure or bench test the unit.
Primary Index Global
0 * OFF
1 Wet Well 1
2 Wet Well 2
Values 3 Reservoir 1
4 Reservoir 2
5 Screen
6 Alarms
• P110 Level Source
• P111 Relay Control Function
Alters • P112 Relay On Setpoint
• P113 Relay OFF Setpoint
• P121 Pump by Rate
Related • P001 Operation

Select an application that is similar to yours and change the parameters required. If none
suit, then refer to P111 Relay Control Function on page 130.

Note: Programming the relays independently is the most common method used.
Parameters
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 129

 P110 Level Source
Sets the level source on which the indexed relay is assigned to a measurement point.

Please note that Difference and Average settings are MultiRanger 200 features.
Primary Index Relay
Range: 1 to 3
1 * Point # 1 = Transducer One
Values 2 Point # 2 = Transducer Two
3 Point # 3 = Difference (P001=4) or Average (P001=5)
[MR 200] [MR 200]
• P003 Maximum Process Speed
• P700 Max Fill rate
Altered by: • P701 Max Empty rate
• P070 Failsafe Timer
• P071 Failsafe Material Level

MultiRanger 200
Please note that these features are only available on the MultiRanger 200.

In Single Point Mode (standard):

Points 2 and 3 are available only if Operation is set for difference or average
(P001 = 4 or 5).

In Dual Point Mode (optional):

Point 2 is always available, and Point 3 is available only if Operation is set for difference or
average (P001 = 4 or 5).

P111 Relay Control Function

Sets the control algorithm used to trip the relay.
Please note that parameter P111 values vary between the MultiRanger 100 and the
Parameters

MultiRanger 200.
mmmmm

Primary Index Relay

Values See chart below
Altered by • P100 Preset Applications

Use zero 0 (preset) to disable control of the indexed relay.

Note: All relay ON/OFF points must be referenced from Empty (P006), regardless of
Operation Mode selection (POO1).

Page 130 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 MultiRanger 100
Values For P111
Control Type #1 Relay Control
OFF 0* Relay set off, no action (preset)
Level 1 Based on level setpoints ON and OFF
General
Loss of Echo (LOE) 6 When echo is lost
Cable Fault 7 When the circuit to a transducer is opened
At fixed ON and OFF setpoints and allows multiple
Pump Fixed Duty Assist 50
pumps to run
Alternate Duty At rotating ON and OFF setpoints and allows multiple
52
Assist pumps to run
Based on input from external communications. See
Communication 65 Communications section on page 83 for further refer-
ence.
1.
When reading and setting this parameter through Modbus or SmartLinx
communications the parameter values are mapped to different numbers.
See MultiRanger Communications on page 83 for Modbus information or
the relevant SmartLinx®manual.

MultiRanger 200
Values For P111
Control Type #1 Relay Control
Off 0* Relay set off, no action (preset)
Level 1 Based on level setpoints ON and OFF
When level enters the range between ON and OFF
In Bounds 2
setpoints
When level exits the range between ON and OFF set-
General Out of Bounds 3
points
Rate of Change 4 Based on rate setpoints ON and OFF
Temperature 5 Based on temperature setpoints ON and OFF Parameters
Loss of Echo (LOE) 6 When echo is lost
Cable Fault 7 When the circuit to a transducer is opened
mmmmm

Totalizer 40 Every 10y units (P641-P645)

Flow
Flow Sampler 41 Every y x 102 units (P641-P645) or time duration (P115)

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 131

 Values For P111
Control Type #1 Relay Control
At fixed ON and OFF setpoints and allows multiple
Fixed Duty Assist 50
pumps to run or for rake control
At fixed ON and OFF setpoints and allows only one
Fixed Duty Backup 51
pump to run
Alternate Duty At rotating ON and OFF setpoints and allows multiple
52
Assist pumps to run
Alternate Duty At rotating ON and OFF setpoints and allows only one
Pump 53
Backup pump to run
Service Ratio Duty On service ratio at ON and OFF setpoints and allows
54
Assist multiple pumps to run
Service Ratio Duty On service ratio at ON and OFF setpoints and allows
55
Backup only one pump to run
First In First Out As Alternate Duty Assist, resets the relay from stag-
56
(FIFO) gered OFF setpoints
Used to control a pump flushing device based on
Flush Valve 64
Flush Systems (P170 to P173)
Control Based on input from external communications. See
Communication 65 Communications section on page 83 for further refer-
ence.
1.
When reading and setting this parameter through Modbus or SmartLinx
communications the parameter values are mapped to different numbers.
See the MultiRanger Communications section on page 83 for Modbus
information or the relevant SmartLinx® manual.

P112 Relay ON Setpoint

Sets the process point at which the relay changes from its NORMAL state.
Primary Index Relay
Range: -999 TO 9999
Parameters

Values
Preset: ----
mmmmm

Altered by • P007 Span

• P100 Preset Applications
Related • P111 Relay Control Function
• P113 Relay OFF Setpoint

For most applications, the relay is tripped at this point. For IN-BOUNDS and OUT-OF-
BOUNDS alarms, it is the high point in the specified range. This parameter is set
according to Span (P007) even when another reading, such as volume, is shown on
the LCD.

Page 132 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P113 Relay OFF Setpoint
Sets the process point at which the relay returns to its NORMAL state.
Primary Index Relay
Range: -999 TO 9999
Values
Preset: ----
Altered by • P007 Span
• P100 Preset Applications
Related • P111 Relay Control Function
• P112 Relay ON Setpoint

For most applications, the relay is reset at this point. For IN-BOUNDS and OUT-OF-
BOUNDS alarms, it is the low point in the specified range. This parameter is set to Span
(P007), even when another reading, such as volume, is shown on the LCD.

P115 Relay Interval Setpoint [MR 200]

The length of time in hours between starts.
Primary Index Relay
Range: -999 TO 9999
Values
Preset: 0.000
Altered by • P100 Preset Applications
Related • P111 Relay Control Function

P116 Dead Band [MR 200]

The distance above and below the bound alarm setpoints.
Primary Index Relay
Range: 0.000 to 9999
Values
Preset: 2% of span
• P111 Relay Control Function
Parameters
Related • P112 Relay ON Setpoint mmmmm

• P113 Relay OFF Setpoint

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 133

 For IN-BOUNDS and OUT-OF-BOUNDS Relay Functions (P111 = 2 and 3 respectively), a
dead band prevents relay chatter due to material level fluctuations at both the upper and
lower setpoints.

Actual ON or OFF setpoint

Enter the dead band in either percent
of span or units of measure (P005). P116
The dead band value is applied both Setpoint set in P112 or P113
above and below the upper and lower
P116
bound setpoints as shown in the fig-
ure. Actual OFF or ON setpoint

P118 Relay Output Logic

The logic applied to relays to determine the contact open or closed state.
Primary Index Relay
Alarm Pump or Control
Value Logic
Contact Contact
Values
2 * Positive Normally Closed Normally Open
3 Negative Normally Open Normally Closed
Related • P111 Relay Control Function

The relay contact operation is NORMALLY CLOSED for alarms and NORMALLY OPEN for
controls. See P111 Relay Control Function for more information.

Power Failure
When power is cut to the MultiRanger, its relays fail to the following states:
Relay States
Relay Fail State
Parameters

1,2,4,5 Open
3,6 Open or Closed1
mmmmm

1.
Relays 3 and 6 are Form C types, so you can wire it either
NORMALLY OPEN or NORMALLY CLOSED. Check the wiring
before programming.

To use relays 3 or 6 as general alarm indicators, set P118 to 3 – negative logic and wire
the alarm for normally open operation. When an alarm event occurs (see below) or when
power is cut, the circuit closes and the alarm activates.

Positive Logic
In software, all relays are programmed the same way, with ON setpoints indicating when
to change the relay contact state (open or closed). This parameter allows the reversal of
the operation so that relay contacts can be NORMALLY CLOSED or NORMALLY OPEN.
P118 is preset to 2 which is positive logic.

Page 134 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Negative Logic
When P118 = 3 (negative logic), the operation for the indexed relay is reversed from
normal.

P119 Relay Logic Test

Forces the relay control logic into an ACTIVATED or DE-ACTIVATED state.
Primary Index Relay
0 * OFF - Control from MultiRanger algorithms
Values 1 Activate relay control
2 De-activate relay control
• P111 Relay Control Function
Related
• P910 Toggle Relays

This parameter tests site wiring and control logic programming. Forcing the relay to an
activated or de-activated state is similar to the MultiRanger detecting an event and
responding to it. Helpful in testing new installations and diagnosing control problems.

Pump Setpoint Modifiers (P121 and P122) [MR 200]

Please note that these parameters apply to the MultiRanger 200 only.
These parameters provide alternate ways of starting the pumps in the pump group. See
the Pump Control section on page 52 for descriptions of the pump control algorithms.

P121 Pump by Rate [MR 200]

Sets the pump relays to accept control by rate of level change once the first ON setpoint
is reached.
Standard Mode Dual Point Mode
Primary Index
Transducer Level
Parameters
0 * OFF (pump by level)
Values mmmmm

1 ON (pump by rate)
• P007 Span
• P111 Relay Control Function
Related
• P132 Pump Start Delay
• Rate (P700 to P708)

Use this function when multiple pumps are to be controlled by rate of level change rather
than by setpoints.
The delay between pump starts is set by P132 Pump Start Delay.
This only applies to any relays set to pump control (P111 = 50 to 56).

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 135

 Notes:
• All pump control relay ON and OFF setpoints must be the same value
• If the level is within 5% of Span (P007) of the OFF setpoint, the next pump is not
started

P122 Pump Service Ratio [MR 200]

Selects pump usage based on the RUN time ratio rather than last used.
Primary Index Relay
Range: 0.000 to 9999
Values
Preset: 20.00
Related • P111 Relay Control Function

This parameter only relates to relays with P111 = 54 or 55.

To make this parameter useful, assign it to all of the pump relays. The number assigned to
each pump relay represents the ratio applied to decide the next pump to start or stop.

Notes:
• The MultiRanger will not sacrifice other pumping strategies to ensure that the ratio
is held true
• If the pump relays are set to the same value then the ratio equals 1:1 and all pumps
are used equally (preset)

Independent Relay Failsafe (P129)

P129 Relay Failsafe
Sets the failsafe operation per relay to allow for more flexible programming.
Primary Index Relay
Parameters

OFF * Response governed by P071 Failsafe Material Level

Values HOLd For LAST KNOWN relay state retention
mmmmm

dE To have the relay de-energize immediately on failsafe

En To have the relay energize immediately on failsafe
Altered by • P071 Failsafe Material Level
• P070 Failsafe Timer
• P111 Relay Control Function

Use this for operations independent of the Failsafe Material Level (P070).

Page 136 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Relay Failsafe is only available for the following relay functions (P111) and is not used for
any other relay control function.

Relay Function (P111) Preset (P129)

1 – level alarm

2 – in bounds alarm

3 – out of bounds alarm OFF

4 – rate of change alarm

5 – temperature alarm

50 to 56 – all pump controls dE

To select an independent Relay Failsafe value:

1. Press FUNCTION to display the Auxiliary Function symbol.
2. Press ARROWS to scroll through the failsafe options.
3. Select option and press ENTER .

Advanced Pump Control Modifiers (P130 to P137)

[MR 200]
Please note that these parameters apply to the MultiRanger 200 only.
These parameters only affect relays set to pump operation (P111 = 50 to 56).

P130 Pump Run-On Interval [MR 200]

Sets the number of hours between pump run-on occurrences.
Primary Index Global
Parameters

Values Range: 0.000 to 1000 mmmmm

Preset: 0.000

Related • Advanced Pump Control Modifiers (P130 to P136)

To clear sediment in a pump-down wet well, run the pump after the normal OFF setpoint
is reached to force some solid material through. This parameter sets the time between
such events. Only the last pump running can run-on.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 137

 P131 Pump Run-On Duration [MR 200]
Sets the number of seconds that the pump runs on.
Primary Index Global

Range: 0.0 to 9999

Values
Preset: 0.000

Related • Advanced Pump Control Modifiers (P130 to P136)

Your pump capacity determines the amount of material that can be removed. Choose a
value long enough to clean out the vessel bottom, yet short enough not to run the pump
dry. Also be sure that this value does not overlap with P130 (Interval). The timing should
look something like this:

P131 P130 (Pump Run-On) P132

P132 Pump Start Delay [MR 200]

Sets the minimum delay (in seconds) between pump starts.
Primary Index Global

Range: 0.0 to 9999

Values Preset: 10 seconds

Value is divided by 10 in simulation mode.

• Advanced Pump Control Modifiers (P130 to P136)

Related
• P121 Pump by Rate

Use this feature to reduce a power surge from all pumps starting at the same time. This
Parameters

delay determines when the next pump is permitted to start.

mmmmm

P133 Pump Power Resumption Delay [MR 200]

Sets the minimum delay before the first pump restarts after power failure.
Primary Index Global

Range: 0.000 to 9999

Values
Preset: 10 seconds

• Advanced Pump Control Modifiers (P130 to P136)

Related
• P132 Pump Start Delay

This reduces the surge from the first pump starting immediately on power resumption.
When this delay expires, other pumps will start as per P132.

Page 138 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P136 Wall Cling Reduction [MR 200]
Varies the upper and lower setpoints to reduce material buildup on the walls.

Standard Mode Dual Point Mode

Primary Index
Global transducer

Range: 0.000 to 9999

Values
Preset: 0.000

This value is the range in which the setpoints are allowed to deviate in percent or units.
The Relay Setpoints ON and OFF values are randomly varied inside the range to ensure
that the material level does not consistently stop at the same point.

Level Setpoint ON

Random Setpoint Range Wall Cling Value

Level Setpoint OFF

P137 Pump Group [MR 200]

Puts pumps into groups for multiple pump rotations on one transducer.
Primary Index Relay

Range: 1 to 2

Values 1 * group 1 Parameters

2 group 2 mmmmm

• P111 Relay Control Function when P111=52 (Alternate duty

Alters
assist) or 53 (Alternate duty backup)

This feature groups pumps (relay points 1 - 6) into groups 1 or 2. It is applied to pump
rotation and occurs independently within each group.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 139

 Flush Systems (P170 to P173) [MR 200]
Please note that these parameters apply to the MultiRanger 200 only.
Use this feature to control an electrically operated flush valve on a pump to divert some
pump output back into the wet well to stir up sediment.

Notes:
• If any of the following parameters are set to 0, this feature will not work.
• In Dual Point mode, a flush valve can be set up for each of the three available level
inputs (P001 = 4 or 5).

Standard Mode
Enter the EnviroRanger relay number of the pump with the flush valve. The activation of
this pump relay drives the usage of the flush system. Both P172 Flush Interval and P171
Flush Cycles are based on the operation of this relay and control any relay set to P111 =
64, Flush Valve.

Dual Point Mode

The indexed relay is the one that controls the flush device. The value is the pump relay
that is watched by the flush system. Enter the pump relay value into the parameter at the
flush relay index.

Example
If you need to watch pump Relay One to control a flush valve on Relay Two you would set
P170[2]=1.

P170 Flush Pump [MR 200]

Picks the number of the pump relay which triggers the flushing device.

Standard Mode Dual Point Mode

Primary Index
Parameters

Global Relay
mmmmm

Range: 0 to 5
Values
Preset: 0

Related • P111 = 64, Flush Valve

Enter the MultiRanger relay number of the pump with the flush valve. The activation of
this pump relay drives the usage of the flush system. Both P172 Flush Interval [MR 200]
and P171 Flush Cycles [MR 200] are based on the operation of this relay and controls any
relay set to P111 = 64, Flush Valve.

Page 140 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P171 Flush Cycles [MR 200]
Sets the number of pump cycles requiring flush control.

Standard Mode Dual Point Mode

Primary Index
Global Relay

Range: 0 to 9999
Values
Preset: 0

Related • P111 = 64, Flush Valve

If three flush cycles are required after every ten pump cycles then:
P172 (Flush Interval) = 10
P171 (Flush Cycles) = 3

P172 Flush Interval [MR 200]

Sets the number of pump cycles before flush control is enabled.

Standard Mode Dual Point Mode

Primary Index
Global Relay

Range: 0 to 9999
Values
Preset: 0

Related • P111 = 64, Flush Valve

To start a new flush cycle every ten times the pumps are run, set this to 10.

P173 Flush Duration [MR 200]

Parameters
The length of time for each flush cycle that the flush control is active.
mmmmm

Standard Mode Dual Point Mode

Primary Index
Global Relay

Range: 0.000 to 9999 s

Values
Preset: 0.000

Related • P111 = 64, Flush Valve

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 141

 mA Output (P200 to P219)
P200 mA Output Range
Determines the mA output range.
Primary Index mA output

0 off

1 0 to 20 mA

Values 2 * 4 to 20 mA

3 20 to 0 mA

4 20 to 4 mA

Related • P911 mA Output Value

If either 1 or 2 is selected, the mA output is directly proportional to the mA Function. If

either 3 or 4 is selected, then the output is inversely proportional.

P201 mA Output Function

Alters the mA output/measurement relationship.
Please note that parameter P201 values vary between the MultiRanger 100 and the
MultiRanger 200.

MultiRanger 100

Primary Index mA output

value mA function Operation (P001)

0 OFF
Parameters

Values 1 level level

mmmmm

2 space space

3 distance distance

• P202 mA Output Allocation

Related
• P911 mA Output Value

Altered By • P001 Operation

Page 142 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 MultiRanger 200

Primary Index mA output

value mA function Operation (P001)

0 OFF

1 level level, differential, or average

2 space space

3 distance distance

Values 4 volume level or space

5 flow OCM

6 head

7 volume rate

8 mA input

9 comms input

• P202 mA Output Allocation

Related
• P911 mA Output Value

Altered By • P001 Operation

P202 mA Output Allocation

Sets the input source from which the mA output is calculated.
Please note that parameter P202 values vary between the MultiRanger 100 and the
MultiRanger 200.
MultiRanger 100

Primary Index mA output Parameters

1 * Point 1 mmmmm

Values
2 Point 2

Related • P201 mA Output Function

MultiRanger 200

Primary Index mA output

1 * Point 1

Values 2 Point 2

3 Point 3

Related • P201 mA Output Function

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 143

 Enter the Point Number the mA output is based on. This value depends on whether mA
function (P201) is set as transducer or mA input.
If P201 uses a transducer, this parameter can only be altered if P001 (Operation) is set for
DPD or DPA. The values would be 1 for Single Point applications, 1-2 for Dual Point, or 1-3
for DPD or DPA configurations.

P203 mA Output Value / Transducer

Displays current mA output value for the Point Number.
Primary Index Level

Values Range: 0.000 to 22.00 (view only)

This displays as an Auxiliary Reading when key is pressed in the RUN mode and
does not include adjustments made using Trim features (P214 / P215).

Note: This parameter is applicable only if any mA output has the transducer Point
Number as its input source (see P201 and P202).

Independent mA Setpoints (P210 and P211)

Use these features to reference the minimum and/or maximum mA output to any point in
the measurement range.

P201—mA Function
Action
Settings
Enter the material level in Units (P005) or percent of
Level, Space, or Distance
Span (P007) as referenced to Empty (P006).

Enter the volume in Max Volume (P051) units or as a per-

Volume [MR 200]
cent of Max Volume.
Parameters

Enter the flowrate in OCM Max Flow (P604) units or as a

Flow [MR 200]
percent of OCM Max Flow.
mmmmm

Enter the head in level units (P005) or percent of Max

Head [MR 200]
Head (P603).

Enter the volume rate in volume/min. Ensure the % sym-

Volume Rate [MR 200]
bol is displayed before attempting to enter a % value.

mA input or
Not Applicable
Communications Input

Page 144 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P210 0/4 mA Output Setpoint
Sets the process level corresponding to the 0 or 4mA value.
Primary Index mA output
Values Range: -999 to 9999
Related • P211 20 mA Output Setpoint

Enter the value (in applicable units or %) to correspond to 0 or 4 mA.

P211 20 mA Output Setpoint

Sets the process level that corresponds to the 20 mA value.
Primary Index mA output

Values Range: -999 to 9999

Related • P210 0/4 mA Output Setpoint

Enter the value (in applicable units or %) to correspond to 20 mA.

mA Output Limits (P212 and P213)

Use these features to adjust the minimum and/or maximum mA output values, which
should suit the input limit requirements of the external device.

P212 mA Output Min Limit

Sets the minimum mA output value (in mA) to be produced.
Primary Index mA output

Range: 0.000 to 22.00

Values Parameters
Preset: 0.0 or 3.8
mmmmm

• P200 mA Output Range

Related
• P213 mA Output Max Limit

Preset is determined by mA Function (P200). If P200 = 1 or 3, then the preset is 0.0, or if

P200 = 2 or 4, then the preset is 3.8. For P200=1 or 3 (preset is 0.0), this parameter has no
effect because the minimum limit cannot be negative, and the minimum current is always
0.0 mA.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 145

 P213 mA Output Max Limit
Sets the maximum mA output value (in mA) to be produced.
Primary Index mA output

Range: 0.000 to 22.00

Values
Preset: 20.2 mA

Related • P200 mA Output Range / P212 mA Output Min LImit

mA Output Trim (P214 to P215)

This does not affect the P203 value shown, and is used when recalibration of an external
device is impractical.

P214 4 mA Output Trim

Calibrates the 4 mA output.
Primary Index mA output

Values Range: 0 to 9999

Related • P215 20 mA Output Trim

Adjust this value so the device indicates 4.000 mA when P214 is accessed.

P215 20 mA Output Trim

Calibrates the 20 mA output.
Primary Index mA output

Values Range: 0 to 16000

Parameters
mmmmm

Related • P214 4mA Output Trim

Adjust this value so the device indicates 20.00 mA when P215 is accessed.

mA Output Failsafe (P219) [MR 200]

Please note that this parameter applies to the MultiRanger 200 only.

Page 146 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P219 mA Output Failsafe [MR 200]
Use for failsafe operation, independent of the Failsafe Material Level (P071).
Primary Index mA output

Range: 0.000 to 22.00

OFF * mA output responds to Failsafe Material Level (P071).

last known value is held until normal operation

Values HOLd
resumes

LO produce the Empty mA output immediately

HI produce the Span mA output immediately

Related • P201 mA Output Function

Selecting an independent mA Failsafe option:

1. Press MODE to display the Auxiliary Function symbol.

2. Press ARROWS to scroll access the failsafe options.
3. Press ENTER when the desired option displayed.
Or, to produce an mA output at a specific value, enter the value required. This is used only
if mA output is allocated to a transducer (P201 = 1 to 7).

mA Input (P250 to P260) [MR 200]

Please note that these parameters apply to the MultiRanger 200 only.

P250 mA Input Range [MR 200]

Shows the mA input range of the connected mA device. Parameters
Primary Index Global mmmmm

1 0 to 20 mA
Values
2 * 4 to 20 mA

Ensure this range corresponds to the output range of the external device. All level
measurements will equate % of Span with the % of the mA range.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 147

 P251 0 or 4 mA Input Level [MR 200]
Shows the process level corresponding to the 0 or 4 mA value.
Primary Index Global

Range: -999 to 9999%

Values
Preset: 0%

• P006 Empty
Related
• P007 Span

When using an external mA signal to determine level, the input range must be scaled to
give accurate results.

P252 20 mA Input Level [MR 200]

Shows the process level corresponding to the 20 mA value.
Primary Index Global

Range: -999 to 9999%

Values
Preset: 100%

• P006 Empty
Related
• P007 Span

Input range is scaled for accuracy if an external mA signal calculates level.

P253 Input Filter Time Constant [MR 200]

Shows the time constant used in the mA input filter to dampen signal fluctuations.
Primary Index Global

Range: 0 to 9999
Parameters

Values
Preset: 1
mmmmm

This number in seconds is used in the damping calculations. Larger values damp more
than smaller values and 0 disables the signal filter.

P254 Scaled mA Input Value [MR 200]

Shows the resulting level value after scaling.
Primary Index Global

Range: -999 to 9999% (view only)

Values
Preset: calculated from the input mA signal

This parameter is calculated from the input mA signal.

Page 148 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P260 mA Raw Input [MR 200]
Shows the raw mA input supplied by the external device.
Primary Index mA input

Values Range: 0.000 to 20.00 (view only)

Discrete Input Functions (P270 to P275)

Discrete inputs can be used for the following:
• Passing other information to a remote system through communications
• Backup level override
Use the parameters listed above to have discrete inputs modify the unit’s operation.
Use the following parameters to configure the discrete input itself.
See also the Pump Control section on page 52 for a description of the MultiRanger’s
pump control algorithms, including how the discrete inputs alter its operation.

P270 Discrete Input Function

Sets how discrete signals are interpreted by the MultiRanger.
Primary Index Discrete input

0 Forced OFF

1 Forced ON
Values
2 * Normally Open – 0 (DI open), 1 (DI closed)

3 Normally Closed – 0 (DI closed), 1 (DI open)

Related • Pump Control section Parameters

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 149

 P275 Scaled Discrete Input Value
Shows the current value of the discrete input after any scaling is applied.
Primary Index Discrete input

Display: view only

Values: dependent on the function of the discrete input

Range of Values Function (P270)

Values 1 Forced ON

0 Forced OFF

0 (DI open), 1 (DI closed) Normally Open

0 (DI closed), 1 (DI open) Normally Closed

Readings are updated continuously even in PROGRAM mode. The value signals a level
override event.

Standard Data Logging (P300 to P321)

All records can be reset by pressing the CLEAR keys.

Record Temperatures (P300 to P303)

These features display the high and/or low temperatures in °C. When a parameter
relating to a TS-3 Temperature Sensor is accessed, the Point Type display changes to the
TS-3 symbol .

If the unit is powered up without a temperature sensor connected, the value –50°C is
displayed. This information can help trace problems with both built in and external
Parameters

temperature sensors.
mmmmm

P300 Temperature, Transducer Maximum

Shows the highest temperature encountered, as measured by the temperature sensor in
the transducer (if applicable).
Primary Index Transducer

Range: - 50 to 150°C (view only)

Values
Preset: - 50°C

Related • P301 Temperature, Transducer Min

Press CLEAR keys to reset the log after a short circuit on the transducer wiring.

Page 150 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P301 Temperature, Transducer Minimum
View the lowest temperature encountered, as measured by the temperature sensor in
the transducer (if applicable).
Primary Index Transducer

Range: - 50 to 150°C (view only)

Values
Preset: 150°C

Related • P300 Temperature, Transducer Max

Press CLEAR keys to reset the log after an open circuit on the transducer wiring.

P302 Temperature, Sensor Maximum

View the highest temperature encountered, as measured by the TS-3 Temperature
Sensor (if applicable).
Primary Index Global

Range: - 50 to 150°C (view only)

Values
Preset: - 50°C

Related • P303 Temperature, Sensor Min

Press CLEAR keys to reset the log after a short circuit on the transducer wiring.

P303 Temperature, Sensor Minimum

Shows the lowest temperature encountered, as measured by the TS-3 Temperature
Sensor (if applicable).
Primary Index Global Parameters

Range: - 50 to 150°C (view only) mmmmm

Values
Preset: 150°C

Related • P302 Temperature, Sensor Max

Press CLEAR keys to reset the log after an open circuit on the transducer wiring.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 151

 Record Readings (P304 and P305)
This identifies the occurrence of the record high and low level readings. Press CLEAR
keys to reset these values once the installation is working correctly.

P304 Reading Max

Shows the highest Reading calculated (in normal Reading units or %).
Primary Index Level

Values Range: -999 to 9999 (view only)

Related • P305 Reading Min

P305 Reading Min

Shows the lowest Reading calculated (in normal Reading units or %).
Primary Index Level

Values Range: -999 to 9999 (view only)

Related • P304 Reading Max

Pump Records (P310 to P312)

These features to identify pump usage and if the associated Relay Function (P111) is set
for any pump control feature. The value is that of the pump connected to the associated
terminals.
Enter a value to set the current record to that value. Use this if a pump is added with a
known number of hours logged, or the value can be reset to zero 0 after maintenance.
Parameters

P309 Pump RUN Time

mmmmm

Displays the amount of time in minutes since a relay was last activated.
Primary Index Relay

Values Range: 0 to 9999 minutes

Related • Relay Function (P111) set for any pump control feature

Parameter measures the length of time since a relay was asserted, most often to
determine how long a pump has been running. Alternatively, it can monitor a relay to
show how long it has been in a state of alarm. It resets every time the relay is activated.

Page 152 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P310 Pump Hours
View or reset the accumulate ON time for the displayed Relay Number.
Primary Index Relay

Values Range: 0.000 to 9999

Related • Relay Function (P111) set for any pump control feature

Value is displayed with a floating decimal point (the more figures displayed before the
decimal, the fewer displayed after). It is the value displayed when key is pressed in
the RUN mode.

P311 Pump Starts

View or reset the accumulated number of times the Relay Number has been ON.
Primary Index Relay

Values Range: 0 to 9999

Related • Relay Function (P111) set for any pump control feature

This value is displayed when key is pressed and held for five seconds in RUN mode.

P312 Pump Run Ons [MR 200]

View or reset the accumulated number of times the displayed Relay Number has been
held ON via Run On Interval (P130).
Please note that this parameter applies to the MultiRanger 200 only.

Primary Index Relay

Values Range: 0 to 9999

Parameters
Related • Relay Function (P111) set for any pump control feature
mmmmm

Flow Records (P320 and P321) [MR 200]

Please note that these parameters apply to the MultiRanger 200 only.
These features are enabled if Operation is set for OCM (P001 = 6), or an OCM device is
defined (P600 ≠ 0). Use them to identify the occurrence of the record high and low flow
rates as displayed in OCM Max Flow (P604) units, or as a percent of OCM Max Flow.
Press CLEAR keys to reset values once the installation is working correctly.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 153

 P320 Flow Max [MR 200]
View the highest flow rate calculated (in units or %).

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: -999 to 9999 (view only)

Related • P604 Maximum Flow

P321 Flow Min [MR 200]

View the lowest flow rate calculated (in units or %).

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: -999 to 9999 (view only)

Related • P604 Maximum Flow

LCD Totalizer (P322 and P323) [MR 200]

Please note that these parameters apply to the MultiRanger 200 only.
Use these features to view, reset, or preset the eight-digit display totalizer when
Operation is set for OCM or Pumped Volume (P001 = 6 or 7). The eight-digit totalizer is
divided into two groups of four digits. The four least significant totalizer digits are stored
in P322, and the four most significant digits are stored in P323. Adjust these values
separately to set a new total.

Example
Parameters

P323 = 0017
mmmmm

P322 = 6.294
Totalizer Display = 00176.294
Totalizer units are dependent upon programming. Enter zero 0 (if required) to reset the
totalizer to zero. Alternatively, enter any other (applicable) value, to preset the totalizer to
the necessary value.

Note: A second point is available only if the Dual Point Feature is enabled.

Page 154 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P322 LCD Total Low [MR 200]
View and/or alter the four least significant digits of the totalizer value.

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: 0.000 to 9999

• P630 LCD Totalized Multiplier

Related • P633 LCD Totalized Decimal Position
• P737 Primary Reading

P323 LCD Total High [MR 200]

View and/or alter the four most significant digits of the totalizer value.

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: 0.000 to 9999

• P630 LCD Totalized Multiplier

Related • P633 LCD Totalized Decimal Position
• P737 Primary Reading

Profile Records (P330 to P337)

WARNING:
These parameters are for authorized service personnel or technicians familiar with
Siemens Milltronics echo processing techniques.
These features can record up to ten Echo profiles, initiated manually (P330), or
Parameters

automatically (P331 et al). See Scope Displays (P810) for echo profile viewing hardware / mmmmm

software requirements. If ten Profiles are already saved, addresses 1 through 10 are
filled, the oldest automatically initiated record is overwritten. Manually initiated records
are not automatically overwritten. All records are automatically deleted in the event of a
power interruption.
When a record is displayed, results are based on current programming (which may have
been altered since the record was saved). This permits the effect on the echo profile to be
observed when changing an echo parameter.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 155

 P330 Profile Record
Records profiles for later viewing.
Please note that Differential or Average operation is a MultiRanger 200 feature.

Primary Index Echo profile

Code Description
---- no record

A1 automatically recorded profile from Transducer One

Values
A2 automatically recorded profile from Transducer Two

U1 manually recorded profile from Transducer One

U2 manually recorded profile from Transducer Two

In addition to being a profile records library, this provides two functions:

• manually records and saves echo profiles
• displays an echo profile, recorded manually or automatically (oscilloscope)

To select a record address

1. Enter PROGRAM mode and press DISPLAY twice to highlight the index field.
The field shows two underscores _ _.
2. Type the index number. The profile record information is shown.
3. Use ARROWS to scroll through the records.

To manually record a profile

Press TRANSDUCER to fire the transducer and record the echo profile into the
internal scope buffer for display.

MultiRanger 200 Feature

Parameters

For differential or average operation (P001 = 4 or 5), access scope Displays (P810)
parameter to select the transducer number.
mmmmm

MultiRanger 100 and MultiRanger 200 Features

To save a manual record

Press ENTER to copy the echo profile record in the scope buffer and save it in the
selected address in the record library. The parameter value field displays the new record
information.

Page 156 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 To display a record

Press key to enter display auxiliary mode and then:

• Press TRANSDUCER to copy the current echo profile into the scope buffer for
display on an oscilloscope or Dolphin Plus

To delete a record

Press CLEAR and then ENTER to delete the echo profile record in the selected
address. The value returns to - - - -.

P331 Auto Record Enable

Use to enable/disable the Auto Profile Record function.
Primary Index Global

Range: 0 to 1

Values 0 * Off

1 On

P332 Auto Record Transducer

Specifies the Transducer Point Number for which Auto Profile Records are saved.
Please note that Differential and Average operation is a MultiRanger 200 feature.

Primary Index Global

Range: 0 to 2

0 Any transducer
Values
1 * Transducer One
Parameters

2 Transducer Two
mmmmm

Altered By • P001 Operation = 4 or 5

MultiRanger 200
This feature is preset to Point Number 1. (Alteration is only required if differential or
average Operation [P001 = 4 or 5] is selected.)

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 157

 P333 Auto Record Interval
Enter the time to elapse after an Auto Profile Record is saved before another Auto Profile
Record can be saved (subject to all other restrictions).
Primary Index Global

Range: 0.0 to 9999 (minutes)

Values
Preset: 120

Auto Record ON and OFF Setpoints (P334 to P337)

Use Auto Record ON Setpoint (P334) and Auto Record OFF Setpoint (P335) to define the
boundaries within which the level must be, for the resultant Echo Profile to be considered
for an Auto Profile Record.
If ---- is displayed for either P334 or P335, Auto Profile Records are saved regardless of
current level (subject to all other restrictions).
Enter the level value in Units (P005) or percent of Span (P007) as referenced to
Empty (P006).

P334 Auto Record ON Setpoint

Enter the critical level which, in conjunction with Auto Record OFF Setpoint, defines the
boundaries for Auto Profile Records to be saved.
Primary Index Global

Values Range: -999 to 9999

• P335 Auto Record OFF Setpoint

Related • P336 Auto Record Filling / Emptying
• P337 Auto Record LOE Time
Parameters

P335 Auto Record OFF Setpoint

mmmmm

Enter the critical level which, in conjunction with Auto Record ON Setpoint, defines the
boundaries for Auto Profile Records to be saved.
Primary Index Global

Values Range: -999 to 9999

• P334 Auto Record ON Setpoint

Related • P336 Auto Record Filling / Emptying
• P337 Auto Record LOE Time

Page 158 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P336 Auto Record Filling / Emptying
Use this feature to restrict Auto Profile Records from being saved unless the level is
rising, falling or either.
Primary Index Global

0 * Auto Profile Record on filling or emptying

Values 1 Auto Profile Record on filling only

2 Auto Profile Record on emptying only

• P334 Auto Record ON Setpoint

• P335 Auto Record OFF Setpoint
Related • P337 Auto Record LOE Time
• P702 Filling Indicator
• P703 Emptying Indicator

If the level changes at a rate in excess of the corresponding Filling / Emptying Indicator
(P702 / P703) values, the Echo Profile is saved subject to this and other Auto Profile
Record restrictions.

P337 Auto Record LOE Time

Limits Auto Profile Records from being saved unless extended LOE occurs.
Primary Index Global

Range: 0.0 to 9999 (seconds)

Values
Preset: 0.0

• P334 Auto Record ON Setpoint

Related • P335 Auto Record OFF Setpoint
• P336 Auto Record Filling / Emptying

If the LOE condition exceeds the period entered, the Echo Profile is saved. When set for 0
LOE is not required for an Auto Profile Record to be saved.
Parameters
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 159

 Installation Records (P340 to P342)
P340 Date of Manufacture
View the date of manufacture of this MultiRanger unit.
Primary Index Global

Values Format: YY:MM:DD (view only)

• P340 Date of Manufacture

Related
• P342 Start Ups

P341 RUN Time

View the number of days this MultiRanger has been in operation.
Primary Index Global

Values Range: 0.000 to 9999 (view only)

• P340 Date of Manufacture

Related
• P342 Start Ups

The RUN Time value is updated once a day, and cannot be reset. However, in the event of
a power interruption, the counter won’t advance. Therefore, a unit that is powered down
on a regular basis will not have an accurate value.

P342 Start Ups

The number of times power has been applied since the Date Of Manufacture.
Primary Index Global

Values Range: 1 to 9999 (view only)

Parameters

• P340 Date of Manufacture

Related
mmmmm

• P342 Run Time

Page 160 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Open Channel Monitoring (P600 to P621) [MR 200]
Open Channel Monitoring (OCM) operation is a MultiRanger 200 feature only.
If the MultiRanger is used to monitor open channel flow, alter the following parameters
as required and run a calibration as described in P621.

Note: See Open Channel Monitoring (OCM) on page 67 for application examples
involving common weirs and flumes.

The MultiRanger measures head as referenced to Empty (P006) or OCM Zero Offset
(P605), when Operation is set for OCM (P001 = 6). Flowrate, based on head (at the point of
measure specified by the Primary Measuring Device fabricator) is also calculated and
displayed on the LCD.
Some Primary Measuring Devices require a longer Range Extension (P801) to avoid
entering the LOE failure state if the water level falls below the zero point of the Primary
Measuring Device. See P801 Range Extension on page 195 for more information.

P600 Primary Measuring Device [MR 200]

The type of primary measuring device (PMD) used.

Single Dual
Primary Index
Global Transducer

0 * off (no calculation)

1 Exponential (see P601)

2 Palmer-Bowlus Flume (see P602)

3 H-Flume (see P602)

Values
4 Universal Linear Flow Calculation (see P610, P611)

5 Universal Curved Flow Calculation (see P610, P611)

Parameters

6 BS-3680/ISO 4359 Rectangular Flume (see P602)

mmmmm

7 BS-3680/ISO 1438/1 Thin Plate V-Notch Weir (see P602)

• P601 Flow Exponent

Alters • P602 Primary Measuring Device Dimensions
• P608 Flowrate Units

Altered By • P001 Operation

• P603 Maximum Head

• P604 Maximum Flow
Related • P605 Zero Head
• P610 Head Breakpoints
• P611 Breakpoint

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 161

 The MultiRanger is pre-programmed for common PMD flow calculations. If your PMD is
not listed, select the appropriate Universal Flow Calculation.
Associated parameters Max Head (P603), Max Flow (P604), and Min Head (P605) may be
scroll accessed. If Operation is not set for OCM (P001 = 6), this value is preset to 0. If
Operation is set for OCM, it is preset to 1.

P601 Flow Exponent [MR 200]

The Exponent for the flow calculation formula.

Single Dual
Primary Index
Global Transducer

Range: -999 to 9999

Values
Preset: 1.55

Altered By • P600 Primary Measuring Device

• P603 Maximum Head

Related • P604 Maximum Flow
• P605 Zero Head

Use this parameter if the Primary Measuring Device (P600) is set to 1 (exponential). It
creates an exponential curve with end points set by Max Head (P603) and Zero Head
(P604) and with the curve based on the specified exponent.
If P601 = 1, the flow characteristic is a straight line

Max. Flow A Word on Exponents

(P604)
The exponential equation is
Q = KHP601

Where:
Q = flow
K = internal constant
Parameters

H = head
mmmmm

Zero Flow
Zero Head

Max. Head
(P603)

Use the exponent specified by the PMD manufacturer, if available, or the sample value
given below.

Page 162 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Example Exponents
PMD Type Exponent (sample only)
Suppressed Rectangular Weir 1.50
Cipolletti Weir 1.50
Venturi Flume 1.50
Parshall Flume 1.22 to 1.607
Leopold Lagco 1.547
V-Notch Weir 2.50

P602 Primary Measuring Device Dimensions [MR 200]

The dimensions of the Primary Measuring Device (PMD).

Single Dual
Primary Index
Dimension Transducer and Dimension

ISO 1438/1

1 Notch Angle

2 Discharge Coefficient

ISO 4359

1 Approach width

2 Throat width

3 Hump Height
Index Values for
Supported PMDs
4 Throat Length

5 Velocity coefficient

6 Discharge coefficient
Parameters
Palmer Bowlus
mmmmm

1 Flume width

H Flume

1 Flume height

Altered By • P600 Primary Measuring Device

Use this parameter if the Primary Measuring Device is directly supported (P600=2,3,6,7).
The dimensions required for each PMD vary.
For more information on PMD, see page 67.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 163

 P603 Maximum Head [MR 200]
The level value associated with Maximum Flow, in Units (P005).

Single Dual
Primary Index
Global Transducer

Range: -999 to 9999

Values
Preset: Span (P007) value

• P005 Units
Altered By
• P600 Primary Measuring Device

• P604 Maximum Flow

Related
• P605 Zero Head

This represents the highest head level supported by the PMD and works in conjunction
with Maximum Flow (P604) to define the highest point in the exponential curve. Use it
when the Primary Measuring Device (PMD) requires a maximum head and flow
reference point. This would include Exponential, Palmer Bowlus Flume, H-Flume, and
Universal breakpoints.

P604 Maximum Flow [MR 200]

The maximum flowrate associated with Maximum Head (P603).

Single Dual
Primary Index
Global Transducer

Range: -999 to 9999

Values
Preset: 1000

Altered By • P600 Primary Measuring Device

• P603 Maximum Head

Parameters

Related • P606 Time Units

mmmmm

• P925 Flow Measurement

This represents the flow at the highest head level supported by the PMD. and works in
conjunction with Maximum Head (P603) to define the highest point in the exponential
curve. Use it when the Primary Measuring Device (PMD) requires a maximum head and
flow reference point. This would include Exponential, Palmer Bowlus Flume, H-Flume,
and Universal breakpoints.
Also use this parameter with Time Units (P606) to define the flowrate units. The limitation
of four digits is for the LCD only, and the flowrate value is available with greater precision
through communications.

Page 164 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Example
Conditions Enter
• Flowrate display: millions of gallons/day, • 376.5 for Maximum Flow (P604)
• Maximum flowrate is 376,500,000 gallons/ • and 4 for Time Units (P606).
day

P605 Zero Head [MR 200]

The distance above Empty (P006) in Units (P005) representing zero head (and zero flow).

Single Dual
Primary Index
Global Transducer

Range: -999 to 9999

Values
Preset: 0.000

• P005 Units
Altered By
• P007 Span

• P006 Empty
Related • P801 Range Extension
• P926 Head Measurement

This feature can be used for most weirs and some flumes (e.g. Palmer Bowlus) where the
zero reference is at a higher elevation than the channel bottom.

Transducer

Material level at zero flow

Empty (P006) PMD base

Zero Head (P605)

Parameters
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 165

 P606 Time Units [MR 200]
Determines the units used to display current flow and logging flow values.
Single Dual
Primary Index
Global Transducer
1 seconds
2 minutes
Values
3 hours
4 * days
Alters •
Altered By • P608 Flowrate Units

This is used when the Primary Measuring Device is Ratiometric (P608=0).

Example
Conditions Enter
• Flowrate display: millions of gallons/day, • 376.5 for Maximum Flow (P604)
• Maximum flowrate is 376,500,000 gallons/day • and 4 for Time Units (P606).

P607 Flowrate Decimal [MR 200]

The maximum number of decimal places to be displayed.

Single Dual
Primary Index
Global Transducer

0 no digits after the decimal point

1 1 digit after the decimal point

Values
2 2 digits after the decimal point
Parameters

3 3 digits after the decimal point

mmmmm

Altered By • P060 Decimal Position

In RUN mode, the number of decimal places displayed is automatically adjusted (if
necessary) to prevent the number of Flowrate digits from exceeding display capabilities.
The maximum number of head decimal places is controlled by Decimal Position (P060).

Page 166 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P608 Flowrate Units [MR 200]
The volume units used to display total flow.

Note: Set this parameter only when using BS-3680/ISO 4359 Rectangular Flume
or BS-3680/ISO 1438/1 Thin Plate V-Notch Weir (P600 = 6 or 7). Use the default
value of 0 for P608 when P600 = 1 to 5.

Single Dual
Primary Index
Global Transducer

Ratiometric (P600=all)

0 * Ratiometric calculation (units defined by P604)

Absolute (P600=6,7 only)

1 litres / second

Values 2 cubic metres / hour

3 cubic metres / day

4 cubic feet / second

5 gallons / minute – Imperial

6 million gallons / day – Imperial

7 gallons / minute – U.S.

Values
8 million gallons / day – U.S.

Alters • P606 Time Units

Altered By • P600 Primary Measuring Device

Related • P608 Flowrate Units

Parameters
This parameter is enabled only if the primary measuring device (PMD) supports absolute
calculations (P600=6,7). For absolute PMDs (P600=6,7) volume units can be specified mmmmm

using this parameter. If needed, absolute PMDs can still use ratiometric (P608=0) to
accommodate other units.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 167

 P610 Head Breakpoints [MR 200]
The head breakpoints for which flowrate is known.

Single Dual
Primary Index
Global Transducer

Secondary Index Breakpoint

Values Range: 0.000 to 9999

Related • P611 Breakpoint Flowrates

The values in the Span for which flowrates are known. See Universal Calculation Support
on page 77 for how to specify universal flows.

P611 Breakpoint Flowrates [MR 200]

The flowrate corresponding to each Head Breakpoint entered.

Single Dual
Primary Index
Global Transducer

Secondary Index Breakpoint

Values Range: 0.000 to 9999

Related • P610 Head Breakpoints

These are the flowrates for the related breakpoints. See Universal Calculation Support on
page 77 for how to specify universal flows.

Head vs. Flowrate (P610 and P611)

Max. Flow
Parameters

Flow Breakpoints
mmmmm

Zero Flow
Max. Head

Head Breakpoints
Zero Head

Page 168 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P620 Low Flow Cutoff [MR 200]
Eliminates totalizer activity for flows at or below the cutoff value.

Single Dual
Primary Index
Global Transducer

Range: 0.000 to 9999

Values
Preset = 5.000 %, or equivalent units

Altered By • P005 Units

Related • P007 Span

Use this to enter the minimum head in units (P005) or as a percent of span.

P621 Auto Zero Head [MR 200]

Calibrates Zero Head (P605) based on actual head measurements.

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 9999

• P006 Empty
• P062 Offset Reading
Related
• P605 Zero Head
• P664 Temperature

Use this parameter when the reported head is consistently high or low by a fixed amount.

Before using this feature, verify the following parameters are correct:
• Empty (P006)
• Temperature (P664)
Parameters
• Offset Reading (P062=0) mmmmm

• Zero Head Offset (P605)

Procedure, with “head” steady

1. Press TRANSDUCER to display the calculated head.

2. Repeat step ONE at least FIVE times to verify repeatability.
3. Measure the actual head (with a tape measure or solid rule).
4. Enter the actual head value.
The deviation between the entered Empty (P006) value and the calibrated Empty value is
stored in Offset Correction (P652). Alternatively, the Empty parameter (P006) can be
corrected directly.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 169

 Pumped Volume Totalizer (P622) [MR 200]
The Pumped Volume Totalizer is a MultiRanger 200 feature only.
If the eight-digit totalizer display or a remote totalizer contact closure are desired, alter
the following parameters.

P622 Inflow / Discharge Adjust [MR 200]

The method used to calculate the volume pumped, for pumped total Operation (P001 = 7).
Single Dual
Primary Index
Global Transducer
1 = inflow * / pump cycle
When the pump is off, the MultiRanger estimates the volume of inflow
by recording the rate at which the liquid level changes. When the
pump is operating, the estimated inflow volume is added to the
pumped volume total. When the pump stops, the pumped volume of
the previous pump cycle is added to the total volume pumped in the
totalizer.
Values 2 = inflow * ignored
Inflow is assumed to be 0 while pumps are running.
3 = inflow * / rate (preset)
Volume pumped is adjusted for inflow. Inflow rate is estimated by
assuming that the rate calculated (P708) just prior to the start of the
pump cycle remained constant during the pump cycle. Inflow rate is
averaged using rate filter (P704), rate update time (P705) and rate
update distance (P706) to control how the average rate is calculated.
• P001 Operation
• P704 Rate Filter
Related • P705 Rate Update Time
• P706 Rate Update Distance
• P708 Volume Rate Display
* or discharge
Parameters
mmmmm

Page 170 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Totalizer (P630 to P645) [MR 200]
The Totalizer features apply to MultiRanger 200 only.

P630 LCD Totalized Multiplier [MR 200]

Use this feature if the LCD Total increments by too large (or too small) an amount.

Single Dual
Primary Index
Global Transducer

-3 .001

-2 .01

-1 .1

Values 0 * 1

1 10

2 100

3 1000

4 10,000

5 100,000
Values
6 1,000,000

7 10,000,000

Related • LCD Totalizer (P322 and P323)

Enter the factor (powers of 10 only) by which actual volume is divided, prior to display on
the LCD. Use a value such that the eight-digit totalizer doesn’t roll over between readings.

Example:
Parameters
mmmmm

For an LCD Total display in 1000s of volume units, enter 3.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 171

 P633 LCD Totalized Decimal Position [MR 200]
Enter the maximum number of decimal places to be displayed.
Single Dual
Primary Index
Global Transducer
0 no digits after the decimal point
1 1 digit after the decimal point
Values
2 * 2 digits after the decimal point
3 3 digits after the decimal point
Related • LCD Totalizer (P322 and P323)

Note: Set the decimal position during initial commissioning of the MultiRanger
200. If the position is changed later, the totalizer data in P322 and P323 will be
incorrect and must be reset according to the new decimal value.

In RUN mode, the number of decimal places displayed is not automatically adjusted.
When the LCD Total value is so large as to exceed display capabilities, the total rolls over
to 0 and continues incrementing.

P640 Remote Totalized Multiplier [MR 200]

Use this feature if the remote totalizer (device connected to the relay set for totalizer
operation [relay Function, P111 = 40]), updates too slowly or rapidly.
Single Dual
Primary Index
Global Transducer
-3 .001
-2 .01
Values
-1 .1
0 * 1
1 10
Parameters

2 100
mmmmm

3 1000
Values 4 10,000
5 100,000
6 1,000,000
7 10,000,000
• P001 Operation
• P111 Relay Control Function
Related • P114 Relay Duration Setpoint
• P115 Relay Interval Setpoint
• P645 Relay Duration

Parameter is relevant only if Operation is set to OCM or Pumped Volume (P001 = 6 or 7).
The relays on the MultiRanger have a maximum frequency of 2.5 Hz.

Page 172 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Enter the factor (powers of 10 only) by which actual volume is divided, prior to Remote
Totalizer count increment.

Example:
For a Remote Totalizer update by 1000s of volume units, enter 3.

P641 Flow Sampler Mantissa [MR 200]

Use this feature in conjunction with Flow Sampler Exponent (P642) to establish the
number of flow units required to increment the Flow Sampler (device connected to the
MultiRanger relay set for the flow sampler operation Relay Function, P111 = 41).

Single Dual
Primary Index
Global Transducer

Range: 0.001 to 9999

Values
Preset = 1.000

• P001 Operation
• P111 Relay Control Function
Related
• OCM (P600 to P621)
• P642 Flow Sampler Exponent

This parameter is relevant only if Operation is set to OCM (P001 = 6).

Enter the mantissa (Y) for the exponent (Z) in the formula:
Flow Sampler Increment = Y x 10Z Flow units.

Example: To count once every 4310 (4.31 x 103) flow units:

• set P641 to 4.31 and P642 to 3

P642 Flow Sampler Exponent [MR 200]

Parameters
Use this feature in conjunction with Flow Sampler Mantissa (P641) to establish the
number of flow units required to increment the Flow Sampler (device connected to the
mmmmm

MultiRanger relay set for the flow sampler operation Relay Function, P111 = 41).

Single Dual
Primary Index
Global Transducer

Range: -3 to +7 (integers only)

Values
Preset = 0

• P001 Operation
• P111 Relay Control Function
Related
• OCM (P600 to P621)
• P641 Flow Sampler Mantissa

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 173

 This parameter is relevant only if Operation is set to OCM (P001 = 6).

Enter the exponent (Z) for the mantissa (Y) in the formula:
Flow Sampler Increment = Y x 10Z Flow units.

P645 Relay Duration [MR 200]

Use this feature (if desired) to adjust the minimum contact closure duration of a relay set
as a totalizer, flow sampler, time (control), or aeration (P111 = 40, 41, 60 or 62)
Primary Index Global

Range: 0.1 to 1024

Values
Preset = 0.2 (sec)

Related • P111 Relay Control Function

Enter minimum contact closure duration (in seconds) required by the device connected.

For the flow sampler function this value is used for both the ON time of the relay and the
OFF time between contacts.

P645 on time P645 OFF time

relay contact closed

relay contact open

Range Calibration (P650 to P654)

There are two types of calibration possible:
Offset: Adjusts the measurements by a fixed amount.
Parameters

Sound Velocity: Adjusts speed of sound and changes the measurement calculations.
mmmmm

Do Offset calibration at any steady level unless a Sound Velocity calibration is also done.
If both calibrations are done then do Offset at a known high level and Sound Velocity at a
known low level.

Page 174 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P650 Offset Calibration
Calibrates Empty (P006) if the reported level is consistently high or low by a fixed amount.

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 9999

• P006 Empty • P652 Offset Correction

Related • P062 Offset Reading • P664 Temperature
• P605 Zero Head

Before using this feature, verify the following parameters are correct:
• Empty (P006)
• Temperature (P664)
• Offset Reading (P062)
• Zero Head Offset (P605), if using OCM

Offset Calibration
Begin with a steady level.

1. Press TRANSDUCER to display the calculated reading.

2. Repeat Step One at least five times to verify repeatability.
3. Measure the actual reading (use tape measure).
4. Enter the actual value.
The deviation between the entered Empty (P006) value and the calibrated Empty value is
stored in Offset Correction (P652).

P651 Sound Velocity Calibration

Changes the speed of sound constant.

Single Dual
Parameters
Primary Index mmmmm

Global Transducer

Values Range: -999 to 9999

• P653 Velocity
Related
• P654 Velocity at 20°C

Condition for use of this feature

• The acoustic beam atmosphere is other than air
• The acoustic beam atmosphere temperature is unknown
• The Reading accuracy is acceptable at higher material levels only
For best results, calibrate with the level at a known value near empty.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 175

 Using Sound Velocity Calibration
Ensure a steady level at some low value (P653 and P654 adjusted accordingly)
1. Allow sufficient time for the vapor concentration to stabilize.
2. Press TRANSDUCER to display the calculated reading.
3. Repeat Step Two at least five times to verify repeatability.
4. Measure the actual reading (e.g. with a tape measure).
5. Enter the actual value.
Repeat this procedure if the atmosphere type, concentration, or temperature conditions
are different from when the last sound velocity calibration was performed.

Note: In gasses other than air, the temperature variation may not correspond with the
speed of sound variation. Turn off temperature sensor and use a fixed temperature.

P652 Offset Correction

The value altered when an Offset Calibration is performed.

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 999.0

Related • P650 Offset Calibration

Alternatively, if the amount of Offset Correction required is known, enter the amount to be
added to the Reading before display.

P653 Velocity
The value adjusted based on the Sound Velocity at 20 °C (P654) vs. Temperature (P664)
characteristics of air.

Single Dual
Parameters

Primary Index
Global Transducer
mmmmm

Values Range: 50.01 to 2001 m/s (164.1 to 6563 ft/s)

• P651 Sound Velocity Calibration

Related
• P654 Velocity at 20°C

Alternatively, enter the current sound velocity (if known), or perform a Sound Velocity
Calibration (P651). The units used are m/s if P005 = 1, 2, or 3 (ft/s if P005 = 4 or 5).

Page 176 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P654 Velocity at 20°C
This value is used to automatically calculate Sound Velocity (P653).

Single Dual
Primary Index
Global Transducer

Values Range: 50.01 to 2001 m/s (164.1 to 6563 ft/s)

• P005 Units
Related • P651 Sound Velocity Calibration
• P653 Velocity

After performing a Sound Velocity Calibration, check this value to verify the acoustic
beam atmosphere is air (344.1 m/s or 1129 ft/s).
Alternatively, if the acoustic beam atmosphere sound velocity at 20°C (68 °F) is known,
and the sound velocity vs. temperature characteristics are similar to that of air, enter the
sound velocity.
The units used are m/s if P005 = 1, 2, or 3 (or ft/s if P005 = 4 or 5).

Temperature Compensation (P660 to P664)

P660 Temp Source
Source of the temperature reading used to adjust the speed of sound.
Primary Index Transducer

1 * AUTO

2 Temp Fixed

Values 3 Ultrasonic/Temperature Transducer Parameters

4 TS-3 Temperature Sensor mmmmm

5 Average (TS-3 and transducer)

Alters • P664 Temperature

• P651 Sound Velocity

• P653 Velocity
Related
• P654 Velocity at 20°C
• P661 Temp Fixed

The MultiRanger uses the TS-3 temperature sensor assigned to the transducer. If one is
not connected, the ultrasonic/temperature transducer is used. If the transducer does not
have an internal temperature sensor, the Temp Fixed (P661) value is used.
If the acoustic beam atmosphere temperature varies with distance from the transducer,
connect a TS-3 Temperature Sensor and ultrasonic / temperature transducers, and select
average.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 177

 In gasses other than air, the temperature variation may not correspond with the speed of
sound variation. In these cases turn off the temperature sensor and use a fixed
temperature.

P661 Temp Fixed

Use this feature if a temperature sensing device is not used.
Primary Index Transducer

Values Range: -199 to 199 (preset = 20 °C)

• P651 Sound Velocity Calibration

• P653 Velocity
Related
• P654 Velocity at 20°C
• P660 Temp Source

Enter the temperature (in °C) of the atmosphere within the transducer acoustic beam. If
the temperature varies with distance from the transducer, enter the average temperature.

P663 Temperature Transducer Allocation

This feature may only be used for differential or average Operation (P001 = 4 or 5).
Primary Index Transducer

1 * Transducer One

Values 2 Transducer Two

1:2 Transducer One and Two average

• P651 Sound Velocity Calibration

Related • P653 Velocity
• P654 Velocity at 20°C

As preset, the temperature measurements of Ultrasonic / Temperature Transducer One

and Two are allocated to Points 1 and 2 respectively.
Parameters

Use this feature if the temperature measurement from both transducers should be
mmmmm

identical, but one is located close to a radiant heat source. Allocate the temperature
measurement of the other transducer to both transducer Point Numbers.
Enter the number of the Transducer whose temperature measurement will be used for
the distance calculation of the Point Number displayed. When both transducers are
allocated to a Point Number, the temperature measurements from each are averaged.

Page 178 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P664 Temperature
View the transducer temperature in °C.
Primary Index Transducer

Values Range: -50 to 150 (view only)

Altered By • P660 Temp Source

• P651 Sound Velocity Calibration

• P653 Velocity
Related
• P654 Velocity at 20°C
• P661 Temp Fixed

Value is displayed when is pressed in RUN mode (see Readings in Run Mode on
page 18).
If Temp Source (P660) is set to any value other than Fixed Temp, the value displayed is the
temperature measured. If Temp Source is set to Fixed Temp, the P661 value is displayed.

Rate (P700 to P708)

These parameters determine how material level changes are reported.

P700 Max Fill Rate

Adjusts the MultiRanger response to increases in the actual material level (or advance to
a higher Failsafe Material Level, P071).

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999

Parameters
Altered by • P003 Maximum Process Speed
mmmmm

• P005 Units
Related • P007 Span
• P071 Failsafe Material Level

Enter a value slightly greater than the maximum vessel filling rate. This value, in Units
(P005) or % of Span (P007) per minute, is automatically altered when Maximum Process
Speed (P003) is altered.
P003 Value Meters/Minute
1 0.1
2 1
3 10

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 179

 P701 Max Empty Rate
Adjusts the MultiRanger response to decreases in the actual material level (or advance
to a lower Failsafe Material Level, P071).

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999

Altered by • P003 Maximum Process Speed

• P005 Units
Related • P007 Span
• P071 Failsafe Material Level

Enter a value slightly greater than the maximum vessel emptying rate. This value, in Units
(P005) or % of Span (P007) per minute, is automatically altered when Maximum Process
Speed (P003) is altered.
P003 Value Meters / Minute
1 0.1
2 1
3 10

P702 Filling Indicator

The fill rate required to activate the LCD Filling indicator ( ).
Primary Index Single Dual

Global Transducer

Values Range: -999 to 9999

Altered by • P003 Maximum Process Speed

Parameters

• P005 Units
mmmmm

Related • P007 Span

• P700 Max Fill Rate

This value (in Units (P005) or % of Span (P007) per minute) is automatically set to 1/10 of
the Max Fill Rate (P700).

Page 180 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P703 Emptying Indicator
The empty rate required to activate the LCD Emptying indicator ( ).

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 9999

Altered by • P003 Maximum Process Speed

• P005 Units
Related • P007 Span
• P701 Max Empty Rate

This value (in Units (P005) or % of Span (P007) per minute) is automatically set to 1/10 of
the Max Empty Rate (P701).

P704 Rate Filter

Damps Rate Value (P707) fluctuations.

Single Dual
Primary Index
Global Transducer

0 Rate display not required

Filtered Output

1 Continuously filtered and updated

Interval Output
Values
2 1 minute or 50 mm (2 in)

3 5 minutes or 100 mm (3.9 in)

Parameters
4 10 minutes or 300 mm (11.8 in)
mmmmm

5 10 minutes or 1000 mm (39.4 in)

Alters • P707 Rate Value

Altered by • P003 Maximum Process Speed

Related • P705 Rate Update Time/ P706 Rate Update Distance

Enter the time or distance interval over which the Rate Value is to be calculated before
the display updates.
This is automatically altered along with Maximum Process Speed (P003).
This value automatically alters the Rate Update Time (P705) and / or Rate Update
Distance (P706). Alternatively, these parameter values may be altered independently.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 181

 P705 Rate Update Time
The time period (in seconds) over which the material level rate of change is averaged
before Rate Value update.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999

Related • P707 Rate Value

P706 Rate Update Distance

The material level change (in metres) to initiate a Rate Value update.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999

Related • P707 Rate Value

P707 Rate Value

The rate of material level change (in Units (P005) or % of Span (P007) per minute).

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 9999 (view only)

Altered By • P704 Rate Filter

Parameters

• P005 Units
Related
mmmmm

• P007 Span

A negative rate indicates the vessel is emptying.

This is the value displayed when is pressed in the RUN mode as described in the
Readings in RUN Mode chart on page 18.

Page 182 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P708 Volume Rate Display [MR 200]
The rate of change of volume in percent of maximum volume per minute.
Please note that this feature applies to the MultiRanger 200 only.

Single Dual
Primary Index
Global Transducer

Values Range: -999 to 9999 (view only)

Related • P622 Inflow / Discharge Adjust

This value is used internally to calculate inflow in pumped volume applications (P622=3).
Press READING to toggle between percent and volume.

Measurement Verification (P710 to P713)

P710 Fuzz Filter
Use this to stabilize the reported level, due to level fluctuations (such as a rippling or
splashing liquid surface) within the Echo Lock Window (P713).

Single Dual
Primary Index
Global Transducer

Values Range: 0 to 100 (0 = off)

Altered by • P003 Maximum Process Speed

• P007 Span
Related
• P713 Echo Lock Window

This value (in % of Span, P007) is automatically altered when Maximum Process Speed Parameters
(P003) is altered. The higher the value entered, the greater the fluctuation stabilized. mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 183

 P711 Echo Lock
Use this feature to select the measurement verification process.

Single Dual
Primary Index
Global Transducer

0 Off

1 Maximum verification
Values
2 * Material agitator

3 Total lock

• P700 Max Fill Rate

• P701 Max Empty Rate
Related • P712 Echo Lock Sampling
• P713 Echo Lock Window
• P820 Algorithm

If a material agitator (mixer) is used in the vessel monitored, set Echo Lock for maximum
verification or material agitator to avoid agitator blade detection. Ensure the agitator is
always ON while the MultiRanger is monitoring the vessel to avoid stationary blade
detection.

When set for max verification or material agitator, a new measurement outside of the
Echo Lock Window (P713) must meet the sampling criterion (P712).

For total lock, Echo Lock Window (P713) is preset to zero 0. The MultiRanger continuously
searches for the best echo according to the algorithm chosen (P820). If the selected echo
is within the window, the window is then centered about the echo. If not, the window
widens with each successive shot until the selected echo is within the window. The
window then returns to its normal width.
When Echo Lock is OFF , the MultiRanger responds immediately to a new measurement
as restricted by the Max Fill / Empty Rate (P700 / P701); however, measurement reliability
Parameters

is affected.
mmmmm

Page 184 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P712 Echo Lock Sampling
The sampling criterion sets the number of consecutive echoes appearing above or below
the echo currently locked onto, that must occur before the measurements are validated
as the new reading (for Echo Lock P711 values: 1 or 2).

Single Dual
Primary Index
Global Transducer

Range: 1:1 to 99:99

Format: x:y
Values
x = the number of above echoes

y = the number of below echoes

Related • P711 Echo Lock

P711 value P712 preset value

1, max verification 5:5
2, material agitator 5:2

Example:
Setting
• P711 = 2, material agitator
• P712 = 5:2
Result
• a new reading will not be validated unlessfive consecutive measurements higher or
two consecutive measurements lower than the current reading occur
• Resetting P711 returns P712 to the respective preset values
Parameters

P713 Echo Lock Window mmmmm

Adjusts the size of the Echo Lock Window.

Single Dual
Primary Index
Global Transducer

Range: 0.000 to 9999

Values
Preset: 0.000

Altered by • P003 Maximum Process Speed

• P005 Units
Related
• P711 Echo Lock

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 185

 The Echo Lock Window is a distance window (units P005) centred on the echo and used
to derive the Reading. When a new measurement is in the window, it is re-centred and
the new Reading calculated. Otherwise, the new measurement is verified by Echo Lock
(P711) before the reading is updated.
When 0 is entered the window is automatically calculated after each measurement. For
slower P003 Maximum Process Speed values the window is narrow, for faster P003
values the window becomes wider.

Transducer Scanning (P726 to P729)

P726 Level System Sync
Enables the System Sync on the terminal block.
Primary Index Global

0 not required
Values
1 * synchronize level monitors

Use this if another level measurement system is mounted nearby, and they are wired
together on the Sync terminal.

P727 Scan Delay

The delay, in seconds, between measurements from transducer points (dual point model
only).
Primary Index Global

Range: 0.000 to 9999

Values
Preset: 5.0

Altered by • P003 Maximum Process Speed

Parameters
mmmmm

Related • P001 Operation

This feature may only be used to adjust the delay before the next point is scanned. Enter
the amount of delay in seconds. This value is automatically altered when Maximum
Process Speed (P003) is altered.

Page 186 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P728 Shot Delay
The delay, in seconds, between transducer shots.
Primary Index Transducer

Range: 0.1 to 4.0

Values
Preset: 0.5

Use this if transient acoustic noise within the vessel is causing measurement difficulties
due to echoes from one shot being received on the next. If more than one ultrasonic unit
is installed for redundancy, this value should be 0.

P729 Scan Time

View the elapsed time (in seconds) since the point displayed was last scanned.
Primary Index Level Point

Values Range: 0.000 to 9999 (view only)

Related • P001 Operation

This may be viewed as an Auxiliary Reading in the RUN mode.

Display (P730 to P739)

P730 Auxiliary Reading
Use this feature to display operator selected Auxiliary Readings temporarily or
indefinitely (as desired).
Primary Index Global
Parameters
Range: 000 to 999
Values mmmmm

Display: OFF, HOLd

Select OFF to display Auxiliary Readings temporarily. Select HOLd to display Auxiliary
Readings until another Auxiliary Reading is selected or programming mode is entered.
See the Hand Programmer section on page 22 for RUN mode auxiliary readings.

Selecting the Auxiliary Reading operation

1. Press READING to display the Auxiliary Function symbol.

2. Press ARROWS to access the OFF or HOLd option desired.
3. Press ENTER

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 187

 If necessary, enter the Parameter Number to default in the Auxiliary Reading display. That
value will show in the auxiliary reading area by default. Other values are available but will
reset to the parameter defined here.

P731 Auxiliary Reading Key

Enter the Parameter Number whose value is to be displayed in the Auxiliary Reading field
Primary Index Global

Range: 000 to 999

Values
Preset: Material Reading, P921

P is pressed in the RUN mode. See the Hand Programmer section on page 22 for RUN
mode auxiliary readings.

P732 Display Delay

Adjusts the Point Number display scroll speed.
Primary Index Global

Range: 0.5 to 10
Values
Preset: 1.5 seconds

• P001 Operation
Related
• P737 Primary Reading

Use this feature to adjust the delay before the display advances to the next Point Number.
Display scrolling is independent from transducer scanning.

P733 Scroll Access

Use this feature to select the parameter scroll access option desired.
Parameters

Primary Index Global

mmmmm

0 Off to scroll to all parameters (P001 to P999)

Values 1 * Smart for Quick Start, altered, and tagged parameters

2 Tagged to scroll to operator tagged parameters only

Press READING and to tag / untag any accessed parameter. is displayed to

indicate the parameter accessed is tagged.

Note: Quick Start parameters (P001 – P007) and those changed from factory default
settings cannot be untagged.

Page 188 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P735 Backlight
Controls the LCD backlighting.
Primary Index Global

0 Off

Values 1 * On

2 Keypad activated

The backlight can be forced on or off, or be controlled by a programmer, in which case it

will turn OFF 30 seconds after the last key is pressed.

P737 Primary Reading [MR 200]

The reading shown on the primary reading display when in RUN mode.
Primary Index Global

Range: 0 to 3

1 * Default reading (P920) based on operation (P001)

Values
2 LCD totalizer (P322, P323)

3 Automatically toggle between 1 and 2

• LCD Totalizer (P322 and P323)

Related • P732 Display Delay
• P920 Reading Measurement

When this value indicates TOGGLE, then both readings (default and totalizer) are shown
in the time specified in display delay (P732).

Parameters
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 189

 SmartLinx Reserved (750 to 769)
These parameters are reserved for optional SmartLinx communications cards and vary by
card. Refer to the SmartLinx documentation to determine if any of them are used.

Communications (P770 to P782)

The MultiRanger communication ports are configured by a series of parameters that are
indexed by port. See the Communications section on page 83 for a complete description
of communications set-up.
Communication parameters are indexed to these communication ports, unless otherwise
noted:
Port Description
1 RS-232 port (RJ-11 modular telephone)
2 RS 485 port on terminal block

P770 Port Protocol

The communications protocol used between the MultiRanger and other devices.

Primary Index Communications Port

0 Communications port disabled
1 * Milltronics Dolphin protocol (preset for port 1)
Values 2 Modbus ASCII slave serial protocol
3 * Modbus RTU slave serial protocol (preset for port 2)

The MultiRanger supports the internationally recognized Modbus standard in both ASCII
and RTU formats. Other protocols are available with optional SmartLinx cards.

P771 Network Address

Parameters

The unique identifier of the MultiRanger on the network.

mmmmm

Primary Index Communications Port

Range: 0 to 9999
Values
1 * Preset:

For devices connected with the Milltronics protocol this parameter is ignored. For devices
connected with a serial Modbus slave protocol, this parameter is a number from 1-247.
The network administrator must ensure that all devices on the network have unique
addresses. Do not use the value 0 for Modbus communications as this is the broadcast
address and is inappropriate for a slave device.

Page 190 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P772 Baud Rate
The communication rate with the master device.
Primary Index Communications Port

4.8 4800 baud

9.6 9600 baud

Values
19.2 * 19,200 baud (preset for port 2)

115.2 * 115,200 baud (preset for port 1)

This specifies the rate of communication in Kbaud. Any value may be entered but only the
values shown above are supported. The baud rate should reflect the speed of the
connected hardware and protocol used.

P773 Parity
The serial port parity.
Primary Index Communications Port

0 * No Parity

Values 1 Odd Parity

2 Even Parity

Ensure that the communications parameters are identical between the MultiRanger and
all connected devices. For example, many modems default to N-8-1 which is No parity, 8
data bits, and 1 stop bit.

P774 Data Bits

The number of data bits per character. Parameters

Primary Index Communications Port

mmmmm

Range: 5 to 8
8 * Modbus RTU

Values 7 or 8 Modbus ASCII

7 or 8 Dolphin Plus

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 191

 P775 Stop Bits
The number of bits between the data bits.
Primary Index Communications Port

Range: 1 or 2
Values
1 * Preset:

P778 Modem Available

Sets the MultiRanger to use an external modem..
Primary Index Communications Port

0 * No modem connected
Values
1 Answer only

P779 Modem Inactivity Timeout

Sets the time that the unit will keep the modem connected with no activity.
Primary Index Communications Port

Range: 0-9999 seconds

Values
0 * No timeout

• P778 Modem Available

Related
• P779 Modem Inactivity Timeout

To use this parameter, ensure that P778 (Modem Available) = 1. Ensure that the value is
low enough to avoid unnecessary delays when an unexpected disconnect occurs but
long enough to avoid timeout while you are still legitimately connected. This parameter
value is ignored by the Modbus Master Drivers, as they automatically disconnect when
Parameters

done.
mmmmm

Hanging Up
If the line is idle and the P779 Modem Inactivity Timeout expires, then the modem is
directed to hang up the line. Ensure that P779 is set longer than the standard polling time
of the connected master device. 0 disables the inactivity timer.

Page 192 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P782 Parameter Index Location
Determines where index information is stored for the parameter access area.
Primary Index Global

0 * Global
Values
1 Parameter-Specific

Altered By • P770 Port Protocol

Global (0)
The primary and secondary index values are global (they affect all of the parameter
access area at once) and stored in:
• primary index – R43,999
• secondary index – R43,998

Parameter-Specific (1)
The primary and secondary index values are encoded into the format words found
between R46,000 and R46,999. Each format work corresponds with the R44,000 series
number in the parameter access map. For example, the format register R46,111
corresponds to the parameter P111 and the value is stored in R44,111. If the Modbus
protocol (P770 = 2 or 3) is not used this parameter is ignored.

SmartLinx Hardware Testing

These parameters are used to test and debug a SmartLinx card.

P790 Hardware Error

The results of ongoing hardware tests in the communications circuitry.
Parameters
Primary Index Global
mmmmm

PASS * No errors

Values FAIL Faulty SmartLinx module or MultiRanger

ERR1 Unknown protocol, upgrade software

• P791 Bus Error

Related
• P792 Bus Error Count

If a test does not meet PASS requirements, communication halts and tests repeated until
PASS requirements are met. Communication then resumes.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 193

 P791 Bus Error
Indicates if an error condition is occurring on the bus.
Primary Index Global

0 * No error
Values Error code, refer to the SmartLinx module documenta-
ý
tion for explanation of the code

• P790 Hardware Error

Related
• P792 Bus Error Count

P792 Bus Error Count

A count that increments by 1 each time a bus error (P752) is reported.
Primary Index Global

Range: 0 to 9999
Values
Preset: 0

• P790 Hardware Error

Related
• P791 Bus Error

P794 SmartLinx Module Type

This parameter is used to identify the module type when SmartLinx is used. If you are not
using SmartLinx, this parameter is not functional. Please see the associated SmartLinx
instruction manual for a full description of this parameter.

P795 SmartLinx Protocol

Parameters

This parameter is used to identify the protocol when SmartLinx is used. If you are not
using SmartLinx, this parameter is not functional. Please see the associated SmartLinx
mmmmm

instruction manual for a full description of this parameter.

Page 194 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Echo Processing (P800 to P807)
P800 Near Blanking
The space near the transducer face which cannot be measured.

Single Dual
Primary Index
Global Transducer

Range: 0.000 to 9999

Values Preset: 0.300m (Most transducers)

0.450m (XCT-8, XCT-12)

• P006 Empty
Related • P007 Span
• P833 TVT Start Min

Use this feature if the surface is reported to be near the transducer face but is in fact
much further away. Extend this value when changing transducer location, mounting, or
aiming.
Please note that changing the Near Blanking cannot correct measurement problems.
Ensure that Span (P007) < Empty (P006) minus Near Blanking (P800)

P801 Range Extension

Allows the material level to fall below the Empty setting without reporting LOE.

Single Dual
Primary Index
Global Transducer

Range: 0.000 to 9999

Values
Parameters
Preset: 20% of Span (P007)
mmmmm

• P005 Units
• P006 Empty
Related
• P007 Span
• P004 Transducer

This feature is useful in OCM applications where the Empty level is set to the bottom of
the weir, and above the bottom of the channel, and should be used if the surface
monitored can fall past the Empty (P006) level in normal operation. The value is added to
Empty (P006) and can be greater than the range of the transducer. If the surface
monitored can extend beyond Empty (P006), increase Range Extension (in Units (P005) or
% of Span) such that Empty plus Range Extension is greater than the transducer face to
furthest surface to be monitored distance. This is often the case with OCM when using
weirs and some flumes.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 195

 P802 Transducer with Submergence Shield
Used when the transducer is expected to be submerged on occasion.

Single Dual
Primary Index
Global Transducer

0 * Off
Values
1 Submergence transducer

• P006 Empty
Related • P071 Failsafe Material Level
• Relays

When a transducer with a submergence shield is submerged, the shield traps an air
pocket that creates a special echo. The MultiRanger recognizes the echo and advances
the reading to the highest level and operates displays and outputs accordingly. This
feature is effective for when power is returned while the transducer is submerged.

P803 Shot / Pulse Mode

Determines what type of ultrasonic shots are fired.

Single Dual
Primary Index
Global Transducer

1 Short
Values
2 * Short and long

• P006 Empty
• P805 Echo Confidence
Related
• P804 Confidence Threshold
• P852 Short Shot Range
Parameters

Increases MultiRanger response when the monitored surface is close to the transducer
face. Select short and long to have short and long acoustic shots fired for each
mmmmm

measurement, regardless of the transducer to surface distance. Select short to have only
short shots fired if the Echo Confidence (P805) produced by a short shot exceeds the
short Confidence Threshold (P804) and the monitored surface is always within the Short
Shot Range (P852).

Page 196 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P804 Confidence Threshold
Determines which echoes are evaluated by software.

Single Dual
Primary Index
Global Transducer

Range: 0 to 99:0 to 99
Values
Preset: 10:5

Related • P805 Echo Confidence

Use this feature when an incorrect material level is reported. The short and long shot
Confidence Thresholds are preset to 10 and 5 respectively. When Echo Confidence (P805)
exceeds the Confidence Threshold, the echo is evaluated by Sonic Intelligence®. Values
are entered as two numbers separated by a decimal point. The first number is the short
shot confidence and the second number is the long shot confidence.

Note: The decimal point is replaced with a colon (:) on the display.

P805 Echo Confidence

Displays the echo confidence of the measurement echo from the last shot.
Primary Index Transducer

Format: x:y (view only)

Values x = short (0 to 99)

y = long (0 to 99)

• P804 Confidence Threshold

Related
• P830 TVT Type
Parameters
Use this feature to monitor the effect of transducer aiming, location, and mechanical
transducer / mounting isolation. mmmmm

Both short and long shot Echo Confidence is displayed. (To display this value in the
auxiliary display while the unit is running, press for 4 seconds.)

Display Description
x:-- short shot confidence value, (long shot not used).
--:y long shot confidence value, (short shot not used).
x:y short and long shot confidence values (both used).
E transducer cable is open or short circuited.
--:-- no shots were processed for Sonic Intelligence® evaluation.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 197

 P806 Echo Strength
Displays the strength (in dB above 1 uV RMS) of the echo which was selected as the
measurement echo.
Primary Index Transducer

Values Format: 0 to 99 (view only)

P807 Noise
Displays the average and peak ambient noise (in dB above 1 uV RMS) being processed.
Primary Index Transducer

Format: x:y (view only)

Values x = average (-99 to 99)

y = peak (-99 to 99)

The noise level is a combination of transient acoustic noise and electrical noise (induced
into the transducer cable or receiving circuitry). See Noise Problems in the
Troubleshooting Section on page 227.

Advanced Echo Processing (P810 to P825)

The following parameters are for authorized Siemens Milltronics Service personnel or
technicians familiar with Siemens Milltronics echo processing techniques.

Anatomy of an Echo Profile

The relevant parts of an echo profile are listed here. These are visible in either Dolphin
Plus or an oscilloscope.
TVT curve
selected echo
Parameters

echo profile
mmmmm

echo marker echo lock window

Page 198 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P810 Scope Displays
Captures echo profiles for display on an oscilloscope.
Primary Index Transducer

Display: P, C, n, u, _
Values
Preset: _ _ _ _ (display is off)

Related • P832 TVT Shaper Adjust

Use this feature to monitor the effects of Echo Processing changes.

Connect an oscilloscope to Mother Board TP2 (Scope), TP5 (DCOM), and TP6 (Sync).
Sweep = 10 us / div. to 1 ms / div. (x 100 for real time)
Amplitude = 1 V / div.
Trigger = external

Note: Use of an analog oscilloscope is preferred over a digital oscilloscope.

Any combination of the following Scope Displays is available.

Display Symbol

P C n u

Echo Profile

TVT Curve

Echo Marker

Echo Lock Win-

dow Parameters
mmmmm

Two methods to select Scope Displays:

Scrolling

1. Press READING to display the Auxiliary Function symbol.

2. Press ARROWS to access the desired Reading display symbols.
3. Press ENTER with the desired display symbols displayed.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 199

 1/0 Values
Alternatively, a four-digit binary value may be entered, where a 0 turns the associated
signal display OFF, and a 1 turns the display ON.
1110 = PCn_ :
• Echo Profile, TVT Curve, and Echo Marker displays ON
• Echo Lock Window display OFF

Use the Scope Displays after pressing TRANSDUCER to observe the result of
parameter alterations. Take several measurements to verify repeatability and overcome
Echo Lock (P711) restrictions.

P815 Echo Time Filtered

The time (in ms) from the transmission of the pulse, to when it is processed.
Primary Index Transducer

Values Range: 0.0 to 9999 (view only)

Related • P816 Echo Time Raw

P816 Echo Time Raw

The time (in ms) from the transmit pulse to the processed echo.
Primary Index Transducer

Values Range: 0.0 to 9999 (view only)

Related • P815 Echo Time Filtered

Profile Pointer (P817 to P825)

Parameters

When one of these parameters is accessed, the scope display changes: The Echo Lock
mmmmm

Window becomes the Profile Pointer. The Profile Pointer may be moved to any point on
the Echo Profile to gain specific information about the profile according to the selected
parameter.
To move the Profile Pointer to a specific point, enter the desired value and it will move to
the nearest acceptable Echo Profile point.
Alternatively, to scroll the Profile Pointer along the Echo Profile:

1. Press to display the Auxiliary Function symbol.

2. Press P or P to move the Profile Pointer to the left or right respectively.

3. When the Profile Pointer Parameters are exited, the scope display automatically
changes back to include the Echo Lock Window.

Page 200 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P817 Profile Pointer Time
The time (in ms) from the transmit pulse to the Profile Pointer.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999 (view only)

• P818 Profile Pointer Distance

• P819 Profile Pointer Amplitude
• P820 Algorithm
Related • P821 Spike Filter
• P822 Narrow Echo Filter
• P823 Reform Echo
• P825 Echo Marker Trigger

P818 Profile Pointer Distance

The distance between the transducer face and the Profile Pointer.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999 (view only)

• P817 Profile Pointer Time

• P819 Profile Pointer Amplitude
• P820 Algorithm
Related • P821 Spike Filter
• P822 Narrow Echo Filter
• P823 Reform Echo
• P825 Echo Marker Trigger

P819 Profile Pointer Amplitude

Parameters
mmmmm

The amplitude (in dB above 1 uV) of the Echo Profile at the Pointer position.

Single Dual
Primary Index
Global Transducer

Values Range: 00 to 99 (view only)

• P817 Profile Pointer Time

• P818 Profile Pointer Distance
• P820 Algorithm
Related • P821 Spike Filter
• P822 Narrow Echo Filter
• P823 Reform Echo
• P825 Echo Marker Trigger

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 201

 P820 Algorithm
Chooses the algorithm to generate the measured value from the profile.

Single Dual
Primary Index
Global Transducer

1 ALF = flat Area, Largest, and First average

2 A = flat Area only

3 L = flat Largest only

4 F = flat First only

5 AL = flat Area and Largest average

Values
6 AF = flat Area and First average

7 LF = flat Largest and First average

8 * bLF = smooth Largest or First

9 bL = smooth Largest only

10 bF = smooth First only

• P805 Echo Confidence

• P817 Profile Pointer Time
• P818 Profile Pointer Distance
• P819 Profile Pointer Amplitude
Related
• P821 Spike Filter
• P822 Narrow Echo Filter
• P823 Reform Echo
• P825 Echo Marker Trigger

Use this to select the algorithm(s) the Sonic Intelligence® echo selection is based on.
Use P805 Echo Confidence (page 197) to determine which algorithm gives the highest
confidence under all level conditions. If the wrong echo is processed, observe the echo
Parameters

processing displays and select an alternate algorithm, either by entering the numeric
value desired, or as below:
mmmmm

1. Press MEASURE to display the Auxiliary Function symbol.

2. Press ARROWS to access the desired Reading display symbols.
3. Press ENTER when the required algorithm is displayed.

Page 202 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P821 Spike Filter
Dampens spikes in the echo profile to reduce false readings.

Single Dual
Primary Index
Global Transducer

0 Off
Values
1 * On
• P817 Profile Pointer Time
• P818 Profile Pointer Distance
• P819 Profile Pointer Amplitude
Related • P820 Algorithm
• P822 Narrow Echo Filter
• P823 Reform Echo
• P825 Echo Marker Trigger

Use P821 if interference spikes are on the long shot Echo Profile display.

P822 Narrow Echo Filter

Filters out echoes of a specific width.

Single Dual
Primary Index
Global Transducer

0 = OFF (preset)
Values
greater = wider

• P817 Profile Pointer Time

• P818 Profile Pointer Distance
• P819 Profile Pointer Amplitude
Related • P820 Algorithm
Parameters
• P821 Spike Filter
• P823 Reform Echo
mmmmm

• P825 Echo Marker Trigger

Use this for transducer acoustic beam interference (e.g. ladder rungs). Enter the width of
false echoes (in ms) to be removed from the long shot Echo Profile. When a value is keyed
in, the nearest acceptable value is entered.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 203

 P823 Reform Echo
Smoothes jagged peaks in the echo profile.

Single Dual
Primary Index
Global Transducer

0 = OFF (preset)
Values
greater = wider

• P002 Material
• P817 Profile Pointer Time
• P818 Profile Pointer Distance
• P819 Profile Pointer Amplitude
Related
• P820 Algorithm
• P821 Spike Filter
• P822 Narrow Echo Filter
• P825 Echo Marker Trigger

Use this feature, when monitoring solids (P002 = 2), if the reported level fluctuates
slightly, though the monitored surface is still. Enter the amount (in ms) of long shot Echo
Profile smoothing required. When a value is keyed in, the nearest acceptable value is
entered.

P825 Echo Marker Trigger

The point on the primary echo on which the measured value is based.

Single Dual
Primary Index
Global Transducer

Range: 5 to 95%
Values
Preset: 50%
Parameters

• P817 Profile Pointer Time

• P818 Profile Pointer Distance
mmmmm

• P819 Profile Pointer Amplitude

Related • P820 Algorithm
• P821 Spike Filter
• P822 Narrow Echo Filter
• P823 Reform Echo

Use this feature if the reported material level fluctuates slightly, due to a variable rise in
the leading edge of the true echo on the Echo Profile.
Enter the value (in percent of echo height) to ensure the Echo Lock Window intersects the
Echo Profile at the sharpest rising portion of the Echo Profile representing the true echo.
This value is preset to 50%.

Page 204 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Advanced TVT Adjustment (P830 to P835)
The following parameters are for authorized Siemens Milltronics Service personnel or
technicians familiar with Siemens Milltronics echo processing techniques.
Advanced TVT control applies to long shots only.

P830 TVT Type

Selects the TVT Curve used.

Single Dual
Primary Index
Global Transducer

1 TVT Short Curved

2 TVT Short Flat

3 TVT Long Flat

Values
4 TVT Long Smooth Front

5 TVT Long Smooth

6 TVT Slopes

Altered By • P002 Material

• P805 Echo Confidence

Related
• P835 TVT Slope Min

Select the TVT type which gives the highest confidence (P805) under all level conditions.
Use this parameter with caution, and do not use TVT Slopes with the bF or bLF Algorithm
(P820).

P831 TVT Shaper Parameters

Turns the TVT Shaper ON or OFF. mmmmm

Single Dual
Primary Index
Global Transducer

0 * Off
Values
1 On

Related • P832 TVT Shaper Adjust

Turn the TVT Shaper ON before using P832 and afterwards. Turn the TVT Shaper ON and
OFF while monitoring the effect to pick up the true echo.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 205

 P832 TVT Shaper Adjust
Allows manual adjustment of the TVT curve.

Single Dual
Primary Index
Breakpoint Transducer and Breakpoint

Range: -50 to 50
Values
Preset: 0

• P810 Scope Displays

Related
• P831 TVT Shaper

Use this feature to bias the shape of the TVT curve to avoid selecting false echoes from
fixed objects.
Adjustment to this parameter is best done while viewing the echo profile with Dolphin
Plus. Refer to the Dolphin Plus online help for details. If Dolphin Plus is not available, then
an oscilloscope can be used. When using an oscilloscope, the Echo Lock Window display
becomes the TVT Curve Pointer. See P810 Scope Displays on page 199 for more
information.
The TVT curve is divided into 40 breakpoints, accessible by enabling the point number as
the breakpoint index field. Each breakpoint is normalized to a value of 0, as displayed in
the parameter value field. By changing the breakpoint value, up or down, the intensity of
the bias applied to that breakpoint of the curve is respectively changed. By changing the
value of adjacent breakpoints, the effective bias to the shaper can be broadened to suit
the desired correction. In the case of multiple false echoes, shaping can be applied along
different points of the curve. Shaping should be applied sparingly in order to avoid
missing the true echo.

To change a breakpoint
1. Confirm that P831, TVT shaper, is on.
2. Go to P832.
3. Press PROGRAM twice to highlight the index value.1
Parameters

4. Press ARROWS to scroll through the 40 points (or type in the desired point).
mmmmm

5. Enter the value from –50 to 50.

6. Press .
7. Press TRANSDUCER to update the scope display with the new TVT.

1.
On Dual Point models, press and then press to access the Breakpoints.
(The display shows the icon.)

Page 206 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P833 TVT Start Min
Use this feature to adjust the TVT Curve height to ignore false echoes (or pick up true
echoes) near the start of the Echo Profile.

Single Dual
Primary Index
Global Transducer

Range: -30 to 225

Values
Preset: 50

• P800 Near Blanking

Related
• P834 TVT Start Duration

Enter the minimum TVT Curve start point (in dB above 1 uV RMS).
This feature should only be used if increased Near Blanking (P800) would extend farther
than desired into the measurement range.

P834 TVT Start Duration

Use this feature in conjunction with TVT Start Min (P833) to ignore false echoes (or pick
up true echoes) near the start of the Echo Profile.

Single Dual
Primary Index
Global Transducer

Range: 0 to 9999
Values
Preset: 30

• P833 TVT Start Min

Related
• P835 TVT Slope Min

Enter the time (in ms) for the TVT Curve to decrease from the TVT Start Min (P833) point
to the TVT Curve baseline. Parameters

P835 TVT Slope Min mmmmm

Enter the minimum slope (in dB/s) for the middle of the TVT Curve.
Single Dual
Primary Index
Global Transducer
Range: 0 to 9999
Values
Preset: 200
• P830 TVT Type
Related
• P834 TVT Start Duration

Use this feature to adjust the slope declination, and use it in conjunction with TVT Start
Duration (when a long flat TVT Type is selected) to ensure the TVT Curve remains above
the false echoes in the middle of the Echo Profile. Alternatively, if TVT Type is set for TVT
Slopes (P830 = 6), preset is 2000.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 207

 Advanced Shot Adjustment (P840 to P852)
These parameters are for Siemens Milltronics service personnel only.

P840 Short Shot Number

The number of short shots to be fired (and results averaged) per transmit pulse.

Single Dual
Primary Index
Global Transducer

Range: 0 to 100
Values
Preset: 1

• P841 Long Shot Number

• P842 Short Shot Frequency
• P844 Short Shot Width
Related
• P850 Short Shot Bias
• P851 Short Shot Floor
• P852 Short Shot Range

P841 Long Shot Number

Enter the number of long shots to be fired (and results averaged) per transmit pulse.

Single Dual
Primary Index
Global Transducer

Range: 0 to 200
Values
Preset: 5

Altered By • P003 Maximum Process Speed

• P840 Short Shot Number

Related • P843 Long Shot Frequency
• P845 Long Shot Width
Parameters

This value is automatically altered by Maximum Process Speed (P003).

mmmmm

Page 208 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P842 Short Shot Frequency
Adjust the short shot transmit pulse frequency (in kHz).

Single Dual
Primary Index
Global Transducer

Values Range: 42kH to 46KH

Altered By • P004 Transducer

• P840 Short Shot Number

• P844 Short Shot Width
Related • P850 Short Shot Bias
• P851 Short Shot Floor
• P852 Short Shot Range

This feature is automatically altered when Transducer (P004) is altered.

P843 Long Shot Frequency

Adjust the long shot transmit pulse frequency (in kHz).

Single Dual
Primary Index
Global Transducer

Values Range: 42kH to 46KH

Altered By • P004 Transducer

• P841 Long Shot Number

• P842 Short Shot Frequency
Related
• P843 Long Shot Frequency
• P845 Long Shot Width

This feature is automatically altered when Transducer (P004) is altered.

P844 Short Shot Width Parameters

Adjust the width (in ms) of the short shot transmit pulse. mmmmm

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 5.000

Altered By • P004 Transducer

• P840 Short Shot Number

• P842 Short Shot Frequency
• P845 Long Shot Width
Related
• P850 Short Shot Bias
• P851 Short Shot Floor
• P852 Short Shot Range

This feature is automatically altered when Transducer (P004) is altered.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 209

 P845 Long Shot Width
Adjust the width (in ms) of the long shot transmit pulse.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 5.000

Altered By • P004 Transducer

• P841 Long Shot Number

Related • P844 Short Shot Width
• P843 Long Shot Frequency

This feature is automatically altered when Transducer (P004) is altered.

P850 Short Shot Bias

Use this feature to slant the echo evaluation in favour of the short shot echo when both
short and long shots are evaluated (see Shot Mode, P803).

Single Dual
Primary Index
Global Transducer

Range: 0 to 100
Values
Preset: 20

• P803 Shot / Pulse Mode

• P840 Short Shot Number
• P842 Short Shot Frequency
Related
• P844 Short Shot Width
• P851 Short Shot Floor
• P852 Short Shot Range

P851 Short Shot Floor

Parameters
mmmmm

Enter the minimum echo strength (in dB above 1 uV) derived from a short shot to be
considered for evaluation.

Single Dual
Primary Index
Global Transducer

Range: 30 to 100
Values
Preset: 50

• P840 Short Shot Number

• P842 Short Shot Frequency
Related • P844 Short Shot Width
• P850 Short Shot Bias
• P852 Short Shot Range

Page 210 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P852 Short Shot Range
Enter the maximum distance in Units (P005) to be measured using short shot echoes.

Single Dual
Primary Index
Global Transducer

Values Range: 0.000 to 9999

Altered By • P004 Transducer

• P840 Short Shot Number

• P842 Short Shot Frequency
Related • P844 Short Shot Width
• P850 Short Shot Bias
• P851 Short Shot Floor

This feature is automatically altered when Transducer (P004) is altered.

Test (P900 to P913)

Test Parameters are intended for use by Siemens Milltronics Service personnel.

P900 Software Revision Number

View the EPROM Rev. #.
Primary Index Global

Values Range: 00.00 to 99.99 (view only)

P901 Memory
Press ENTER to activate the MultiRanger memory test.
Parameters
mmmmm
Primary Index Global

Display: view only

PASS (memory test successful)

Values F1 RAM

F3 FLASH data

F4 FLASH code

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 211

 P902 Watchdog
Press ENTER to put the CPU into an infinite loop to test the watchdog timer.
On successful completion (10 seconds) the RUN mode is entered and the MultiRanger is
reset. Programming is kept and the unit responds as if there had been a power failure.

P903 Display
Press ENTER to activate the display test.
All LCD segments and symbols are temporarily displayed.

P904 Keypad
Press ENTER , then press each keypad key in the following sequence:

P P

As each key is pressed, the associated keypad number is displayed. On successful test
completion, PASS is displayed. FAIL is displayed if a key is pressed out of sequence or the
programmer keypad malfunctions.

P905 Transmit Pulse

This feature may be used to monitor the transmit pulse with an oscilloscope connected to
the transducer terminals.

Single Dual
Primary Index
Global Transducer

Values Range: 42kH to 46KH (view only)

Altered By • P004 Transducer

Parameters
mmmmm

Press ENTER to supply repeated transmit pulses, at the frequency entered, to the
transducer and / or view the transducer operating frequency (automatically altered by
P004 Transducer) for the Point Number displayed.

P906 RS-232 Port

Press ENTER to test the RS-232 port on the RJ-11.
An external device must be connected to the RS-232 port for this test. On successful
completion, PASS is displayed, otherwise it is FAIL.

Page 212 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P908 Scanner
Press ENTER to cycle the scanner relay while firing the transmitter.
Use this parameter to ensure that both transducers are being stimulated.

P910 Toggle Relays

Used to energize and de-energize relays directly.
Primary Index Global

Values 0 to 6

Related • P119 mA Relay Logic Test

Enter the relay number and then toggle between energized and de-energized, as
required. Enter 0 to toggle all relays at once.
Applies only to relays with P119 = 0 (algorithm control). Use this parameter to confirm that
relay contacts are opening and closing.
This feature is helpful when P119 does not give expected results even though
programming was verified.

P911 mA Output Value

Access this parameter to display the current value of the mA output.
Primary Index mA output

Values Range: 0.00 to 25.00

• P200 mA Output Range

Related
• P201 mA Output Function

Additionally, this feature may be used to enter a desired value. The mA output
Parameters

immediately assumes the value entered regardless of any restrictions programmed. mmmmm

P912 Transducer Temperature

Use this feature to display the temperature in °C (as monitored by the connected
transducer).
Primary Index Transducer

Values Range: -50 to 150

Err is displayed if the transducer is not equipped with an internal temperature sensor.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 213

 P913 Sensor Temperature
Access this parameter to display the temperature in °C (as monitored by the TS-3).
Primary Index Global

Values Range: -50 to 150

OPEn is displayed if a TS-3 is not connected.

P914 mA Input [MR 200]

Use this feature to display the mA input value (in mA).

Primary Index mA input

Values Range: 0.000 to 24.00

Parameters
mmmmm

Page 214 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Measurement (P920 to P927)
All of these parameters are available in RUN mode and used to verify programming. See
Readings in RUN Mode on page 18.
The range and values shown for each of these parameters depends on the Operation
(P001) chosen. The readings for each operation are listed below.

To Access in RUN Mode

1. Ensure the device is in RUN mode.
2. Press P
.The Auxiliary Reading field becomes underscores P_ _ _
3. Type the parameter number. The field changes to the value of the specified
parameter.
These parameters are also available in simulation mode. See the Testing the
Configuration section page 79 for instructions on how to control the simulation direction
and rate.

P920 Reading Measurement

Corresponds to the final reading after all programming is applied.
Please note that the following features apply only to the MultiRanger 200: Difference,
Average, OCM, and Pump Totalizer.

Primary Index level point

Values Range: -999 to 9999

In general this means that: P920 = Reading x P060 + P061.

Reading Measurements by Operation

P001 P050 = 0 P050 ≠ 0
0 – OFF ---- ----
1 – Level P921 P924
Parameters

2 – Space P922 100% - P924

mmmmm

3 – Distance P927 P927

4 – Difference [MR 200] P921 (indexed) P921 (indexed)
5 – Average [MR 200] P921 (indexed) P921 (indexed)
6 – OCM [MR 200] P925 P925
7 – Pump Totalizer [MR 200] P924 P924

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 215

 P921 Material Measurement
The distance in Units (P005) or % of Span (P007) between Empty (P006) and the
monitored surface.
Primary Index Level Point

Values Range: -999 to 9999

• P005 Units
Related • P006 Empty
• P007 Span

P922 Space Measurement

The distance between the monitored surface and Span (P007).
Primary Index Transducer

Values Range: 0.000 to 9999

Related • P007 Span

P923 Distance Measurement

The distance between the monitored surface and the transducer face.
Primary Index Transducer

Values Range: 0.000 to 9999

P924 Volume Measurement [MR 200]

The calculated vessel capacity in Max Volume (P051) or % of Max Volume.
Please note that Volume Measurement is a MultiRanger 200 feature only.
Parameters
mmmmm

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: 0.000 to 9999

Related • P051 Maximum Volume

Page 216 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

P925 Flow Measurement [MR 200]
The calculated flowrate in Max Flow (P604) units or % of Max Flow.
Please note that Flow Measurement is a MultiRanger 200 feature only.

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: 0.000 to 9999

Related • P604 Maximum Flow

P926 Head Measurement [MR 200]

Corresponds to Head (the distance from Zero Head (P605) to the monitored surface in
Units (P005) or % of Span (P007).
Please note that Head Measurement is a MultiRanger 200 feature only.

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: -999 to 9999

• P005 Units
Related • P007 Span
• P605 Zero Head

P927 Distance Measurement

The distance between the surface and the transducer face.

Primary Index Transducer Parameters

Values Range: 0.000 to 9999 mmmmm

• P005 Units
Related
• P006 Empty

Use P923 unless the distance information is required in percent.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 217

 Master Reset (P999)
This feature resets all parameters to original values.

Standard Mode Dual Point Mode

Primary Index
Global Transducer

Values Range: 0.000 to 9999

Use this feature prior to initial programming if arbitrary Parameter Values were used
during a bench test, or after upgrading the software. Following a Master Reset, complete
reprogramming is required.

To perform a Master Reset, access P999 and press CLEAR . [Link] displays until
the reset is complete.

In dual point units, both points can be reset at the same time by setting the index to 00
and pressing the CLEAR keys.

CAUTION: be careful when using this feature. All data for all points will be reset. For
convenience, be sure to record the values you want to re-enter.
Parameters
mmmmm

Page 218 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

General Appendix A: Index Types

Index types
Name Description # of indexes
Global This parameter applies to the entire unit n/a

View only This parameter can not be set, only viewed n/a

Parameter
Breakpoint Indexed by breakpoint
dependent

Dimension Indexed by PMD dimension up to 7

Discrete Input Indexed by discrete input 2

Echo Profile Indexed by stored echo profile 10

Level Point1 Indexed by level point 1, 2 or 3

mA input1 Indexed by mA input 1

mA output1 Indexed by mA output 0 or 2

Comm. Port Indexed by communications port 2

Relay Indexed by relay 3 or 6

Transducer2 Indexed by transducer 1 or 2

1. MultiRanger 100: The two level points are: Transducer One and Trans-
ducer Two.
Level point typically has 1 index in Single Point Mode (standard), and 2
indexes in Dual Point Mode (optional).
MultiRanger 200: The three level points are: transducer 1, transducer 2,
and the calculated point which can be difference (P001=4) or average
(P001=5).
Level point typically has 1 index in Single Point Mode (standard), and 2
indexes in Dual Point Mode (optional). A third index is available in both
modes when Operation (P001) is set for DPD (P001=4) or DPA (P001=5).

2. MultiRanger 200: The number of indexes available in Single Point Mode

(standard) is typically 1, but can be expanded to 2 if Operation (P001) is
set for DPD (P001=4) or DPA (P001=5).
Appendix A: Index Types

In Dual Point Mode (optional), the number of available indexes is

always 2.
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 219

 Appendix B: Tech Reference General Appendix B–Technical Reference

Transmit Pulse
mmmmm

Thetransmit pulse consists of one or more electrical “shot” pulses, which are supplied to
the transducer connected to the MultiRanger terminals. The transducer fires an acoustic
“shot” for each electrical pulse supplied. After each shot is fired, sufficient time is
provided for echo (shot reflection) reception before the next (if applicable) shot is fired.
After all shots of the transmit pulse are fired, the resultant echoes are processed. The
transmit pulse shot number, frequency, duration, delay, and associated measurement
range are defined by parameters P803 and P840 to P852.

Echo Processing
Echo processing consists of echo enhancement, true echo selection, and selected echo
verification.
Echo Enhancement is achieved by filtering (P821 and P822) and reforming (P823) the echo
profile (P810). The true echo (echo reflected by the intended target) is selected when that
portion of the echo profile meets the evaluation criteria of Sonic Intelligence®.
Insignificant portions of the echo profile outside of the measurement range (Span P006 +
Range Extension P801), below the TVT Curve (P830, and P832 to P835), and less than the
Confidence Threshold (P804) and Short Shot Floor (P851) are automatically disregarded.
The remaining portions of the Echo Profile are evaluated using the Algorithm (P820) and
Short Shot Bias (P850). The Echo Profile portion providing the best Echo Confidence
(P805) is selected.
True echo verification is automatic. The position (relation in time after transmit) of the
new echo is compared to that of the previously accepted echo. When the new echo is
within the Echo Lock Window (P713), it is accepted and displays, outputs, and relays are
updated per the Fuzz Filter (P710) and Rate Parameters (P700 to P703). If the new echo is
outside of the Window, it is not accepted until Echo Lock (P711) requirements are
satisfied.

Scope Display (P810)

Span (P007) + Range
extension (P801)

TVT Curve Echo Lock Window

Echo Profile

Near Blanking (P800) Echo Marker

Page 220 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Dolphin Plus Display

Appendix B: Tech Reference

mmmmm
Cursor

Echo Marker

TVT Curve

Echo Profile

Distance Calculation
To calculate the transducer to material level (object) distance, the transmission medium
(atmosphere) sound velocity (P653) is multiplied by the acoustic transmission to reception
time period. This result is divided by 2 to calculate the one way distance.
Distance = Sound Velocity x Time / 2
The Reading displayed is the result of performing any additional modification to the
calculated distance (as determined by Operation P001, Units P005, Volume Conversion,
P050 to P054, Reading, P060 to P063, OCM, P600 to P611, and/or Totalizer P622 to P633
parameters).

Sound Velocity
The sound velocity of the transmission medium is affected by the type, temperature, and
vapor pressure of the gas or vapor present. As preset, the MultiRanger assumes the
vessel atmosphere is air at 20°C (68°F). Unless altered, the sound velocity used for the
distance calculation is 344.1 m / s (1129 ft / s).
Variable air temperature is automatically compensated when a Milltronics ultrasonic /
temperature transducer is used. If the transducer is exposed to direct sunlight, use a
sunshield or a separate TS-3 temperature sensor.
Also, if the temperature varies between the transducer face and the liquid monitored, use
a TS-3 temperature sensor (submerged in the liquid) in combination with an ultrasonic /
temperature transducer. Set Temp Source (P660) for both, to average the transducer and
TS-3 measurements.
Atmosphere composition other than air can pose a challenge for ultrasonic level
measurement. However, excellent results may be obtained by performing a Sound
Velocity Calibration (P651) if the atmosphere is homogeneous (well mixed), at a fixed
temperature, and under consistent vapor pressure.
The MultiRanger automatic temperature compensation is based on the sound velocity /
temperature characteristics of “air” and may not be suitable for the atmosphere present.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 221

 Appendix B: Tech Reference If the atmosphere temperature is variable, perform frequent Sound Velocity Calibrations
to optimize measurement accuracy.
Sound Velocity calibration frequency may be determined with experience. If the sound
velocity in two or more vessels is always similar, future calibrations may be performed on
one vessel and the resultant Velocity (P653) entered directly for the other vessel(s).
mmmmm

If the sound velocity of a vessel atmosphere is found to be repeatable at specific

temperatures, a chart or curve may be developed. Then, rather than performing a Sound
Velocity Calibration each time the vessel temperature changes significantly, the
anticipated Velocity (P653) may be entered directly.

Scanning
MultiRanger 100/200
When echo processing is complete (if more than 1 vessel is monitored) the scanning relay
changes state to supply the transmit pulse to the other transducer after the Scan Delay
(P727).
Scan Delay is automatically set by Maximum Process Speed (P003). When high speed
scanning is required (sometimes the case for equipment position monitoring), the Scan
Delay may be reduced. Reduce the Scan Delay only as required, otherwise premature
scanning relay fatigue could occur.

MultiRanger 200
When two transducers are connected and configured in a dual point unit, the
MultiRanger will scan each in turn via the scanner relay. When a single point
MultiRanger is programmed for differential or average level Operation (P001 = 4 or 5), two
transducers of the same type must be used.

Volume Calculation [MR 200]

Please note that the Volume Calculation feature is only available on the MultiRanger 200.
The unit provides a variety of volume calculation features (P050 to P055).
If the vessel does not match any of the eight preset Tank Shape calculations, a Universal
Volume calculation may be used. Use the level/volume graph or chart provided by the
vessel fabricator (or create one based on the vessel dimensions). Based on the graph,
choose the Universal Volume calculation, and select the level vs. volume breakpoints to
be entered (32 max). Generally, the more breakpoints entered, the greater the accuracy.

Universal, Linear (P050 = 9)

This volume calculation creates a piece-wise linear approximation of the level/volume
curve. This option provides best results if the curve has sharp angles joining relatively
linear sections.
Enter a Level Breakpoint at each point where the level/volume curve bends sharply (2
minimum).

Page 222 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Appendix B: Tech Reference

mmmmm
For combination curves (mostly linear but include one or more arcs), enter numerous
breakpoints along the arc, for best volume calculation accuracy.

Universal, Curved [MR 200]

Please note that the Universal, Curved feature is only available on the MultiRanger 200.
Set P050 = 10
This calculation creates a cubic spline approximation of the level/volume curve, providing
best results if the curve is non-linear, and there are no sharp angles.

Select at least enough breakpoints from the curve to satisfy the following:
• two breakpoints very near the minimum level
• one breakpoint at the tangent points of each arc
• one breakpoint at each arc apex
• two breakpoints very near the maximum level
For combination curves, enter at least two breakpoints immediately before and after any
sharp angle (as well as one breakpoint exactly at the angle) on the curve.

Flow Calculation
Please note that the Flow Calculation feature is only available on the MultiRanger 200.
The MultiRanger provides numerous OCM flow calculation features (P600 to P611).
If the PMD (primary measuring device) does not match any of the eight preset PMD
calculations, or if a PMD is not used, select a Universal Volume calculation. Use the head/
flow graph or chart provided by the PMD fabricator (or create one based on the PMD or
channel dimensions).
Based on the graph, choose the Universal Flow calculation, and select the head versus
flow breakpoints to be entered (32 max). Generally, the more breakpoints entered, the
greater the flow calculation accuracy.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 223

 Appendix B: Tech Reference Universal, Linear [MR 200]
Please note that the Universal, Linear feature is only available on the MultiRanger 200.
Set P600 = 4.
mmmmm

This flow calculation creates a piece-wise linear approximation of the head/flow curve.
This option provides best results if the curve has sharp angles joining relatively linear
sections.

Enter a Head Breakpoint at each point where the head/flow curve bends sharply (2
minimum). For combination curves (mostly linear but include 1 or more arcs), enter
numerous breakpoints along the arc, for best flow calculation accuracy.
See also Typical Flow Characterization on page 77.

Universal, Curved [MR 200]

Please note that the Universal, Curved feature is only available on the MultiRanger 200.
This calculation creates a cubic spline approximation of the head/flow curve, providing
best results if the curve is non-linear, and there are no sharp angles.

Select at least enough breakpoints from the curve to satisfy the following:
• two breakpoints very near the minimum head
• one breakpoint at the tangent points of each arc
• one breakpoint at each arc apex
• two breakpoints very near the maximum head

Page 224 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 For combination curves, enter at least 2 breakpoints immediately before and after any

Appendix B: Tech Reference

sharp angle (as well as 1 breakpoint exactly at the angle) on the curve. For more
information, go to Typical Flow Characterization on page 77.

Maximum Process Speed

mmmmm
The MultiRanger’s ability to respond to material level changes is designed to exceed even
the most demanding installation requirements.
The Maximum Process Speed setting automatically presets various parameters affecting
the MultiRanger response to material level changes as follows:

Values Dependent on Maximum Process

Parameter
Speed (P003)

(units) 1 (slow) 2 (medium) 3 (fast)

P070 Failsafe Timer (min) 100 10 1

P700 Max Fill Rate (m/min) 0.1 1 10

P701 Max Empty Rate (m/min) 0.1 1 10

P702 Filling Indicator (m/min) 0.01 0.1 1

P703 Emptying Indicator (m/min) 0.01 0.1 1

P704 Rate Filter (option) 4 2 2

P710 Fuzz Filter (% of Span) 100 50 10

P713 Echo Lock Window (per P701 / P702 and time since last valid measurement)

P727 Scan Delay (seconds) 5 5 3

P841 Long Shot Number 10 5 2

If any of these parameters are independently altered, a Maximum Process Speed (P003)
parameter alteration automatically resets the independently altered value.
Slower Maximum Process Speed (P003) provides greater measurement reliability. Faster,
independently set Max Fill (P700) and Max Empty (P701). Rates may be impeded by Echo
Lock (P711), Scan Delay (P727), and Shot Delay (P728) values.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 225

 General Appendix C: Troubleshooting

Note: Many of the parameters and techniques described here require extensive
knowledge of ultrasonic technologies and Siemens Milltronics echo processing
software. Use this information with caution.

If the setup becomes too confusing use P999 to reset and start again.
Appendix C: Troubleshooting

Common Problems Chart

Symptom Cause Action

mmmmm

Display blank, trans- Check power supply, wiring, or

No power.
ducer not pulsing. power fuse.

Check programmer usage:

No response to pro- Obstructed infrared interface, 15 cm (6”) from faceplate
grammer. defective programmer. pointed at upper target.

Short circuited transducer

Displays Short and cable, or defective trans-
Repair or replace as necessary.
tb:(#). ducer at indicated terminal
block number.

Transducer not connected or Check connection to displayed

connection reversed. terminal blocks.
Displays Open and
Open circuited transducer
tb:(#).
cable, or defective trans-
Repair or replace as necessary.
ducer at indicated terminal
block number.

Relocate and/or re-aim trans-

ducer at material.
Displays LOE. Weak or non-existent echo.
Proceed to Measurement Diffi-
culties.

Wrong transducer selected Verify transducer type and re-

(P004). enter value.

Do not tie white and shield

Displays Error and Transducer connected in
together. Use all three terminal
tb:(#). “two wire” method.
blocks.

Transducer connected back- Reverse black and white wires

wards. on terminal block.

Value too large to display in 4 Select larger Units (P005), or

Displays EEEE
or 5 characters. lower Convert Reading (P061).

Page 226 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Alter Maximum Process Speed
Reading fluctuates
Incorrect measurement stabi- (P003) or damping (P704)
while material level is
lization. accordingly. See Maximum Pro-
still (or vice versa).
cess Speed.

Relocate and / or re-aim trans-

Transducer acoustic beam ducer at material level or object.
Reading is fixed,
obstructed, standpipe too
regardless of the Proceed to Measurement Diffi-
narrow, or transducer ringing
actual material level. culties below.
(reads over 100%).
See also: Transducer Ringing.

Appendix C: Troubleshooting
Material level See Empty (P006), Reading Off-
Incorrect Empty (zero) refer-
reported is always set (P063), Offset Calibration
ence for level operation
incorrect by the same (P650), & Offset Correction
(P001 = 1).
amount. (P652).

mmmmm
Measurement accu- Use a transducer with a built-in
temperature sensor or a TS-3
racy improves as Incorrect Sound Velocity used
temperature sensor.
level nears trans- for distance calculation.
ducer.
See Sound Velocity.

Relocate and / or re-aim trans-

Reading is erratic, ducer at material.
True echo too weak or wrong
with little or no rela-
echo being processed.
tion to material level. Check noise parameters. See
Noise Problems.

Noise Problems
Incorrect readings can be the result of noise problems, either acoustic or electrical, in the
application.
The noise present at the input to the ultrasonic receiver can be determined by viewing
parameter P807. The display reads ##:##, where the first number is the average noise and
the second is the peak noise. In general, the most useful value is the average noise.
With no transducer attached the noise is under 5 dB. This is often called the noise floor. If
the value with a transducer attached is greater than 5 dB, then signal processing
problems can occur. High noise decreases the maximum distance that can be measured.
The exact relationship between noise and maximum distance is dependent on the
transducer type and the material being measured. Any average noise level greater than
20 dB is probably cause for concern unless the distance is much shorter than the
maximum for the transducer.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 227

 Determine the Noise Source
Disconnect the transducer from the MultiRanger. If the measured noise is below 5 dB,
then continue here. If the measured noise is above 5 dB go to Non-Transducer Noise
Sources below.
1. Connect only the shield wire of the transducer to the MultiRanger. If the measured
noise is below 5 dB, continue with the next step. If the noise is above 5 dB, go to
Common Wiring Problems.
2. Connect the white and black transducer wires to the MultiRanger. Record the
average noise.
3. Remove the positive wire of the transducer. Record the average noise.
Appendix C: Troubleshooting

4. Re-connect the positive wire and remove the negative wire. Record the average
noise.
Using the table below, determine the appropriate next step. The terms higher, lower and
unchanged refer to the noise recorded in the previous steps.
mmmmm

These are guidelines only. If the suggested solution does not solve the problem, try the
other options also.

- removed + removed Go to:

higher Reducing Electrical Noise

higher unchanged Common Wiring Problems

lower Reducing Acoustical Noise

higher Reducing Electrical Noise

noise

unchanged unchanged Contact Siemens Milltronics

lower Reducing Acoustical Noise

higher Common Wiring Problems

lower unchanged Common Wiring Problems

lower Reducing Acoustical Noise

Acoustical Noise
To confirm that the problem is acoustical, place several layers of cardboard over the face
of the transducer. If the noise is reduced, the noise is definitely acoustical.

Non-Transducer Noise Sources

Remove all input and output cables from the MultiRanger individually while monitoring
the noise. If removing a cable reduces the noise, that cable may be picking up noise from
adjacent electrical equipment. Check that low voltage cables are not being run adjacent
to high voltage cables or near to electrical noise generators such as variable speed
drives.

Page 228 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Filtering cables is an option but is not recommended unless all other options have been
exhausted.
The MultiRanger is designed to work near heavy industrial equipment such as variable
speed drives. Even so, it should not be located near high voltage wires or switch gear.
Try moving the electronics to a different location. Often moving the electronics a few
meters farther from the source of noise will fix the problem. Shielding the electronics is
also an option, but it should be a last resort. Proper shielding is expensive and is difficult
to install properly–the shielding box must enclose the MultiRanger electronics
completely, and all wires must be brought to the box through grounded metal conduit.

Appendix C: Troubleshooting
Common Wiring Problems
• Make sure that the transducer shield wire is connected at the electronics end only.
Do not ground it at any other location.

mmmmm
• Do not connect the transducer shield wire to the white wire.
• The exposed transducer shield wire must be as short as possible.
• Connections between the wire supplied with the transducer, and any customer
installed extension wire should be done in grounded metal junction boxes.
On Siemens Milltronics transducers the white wire is negative and the black wire is
positive. If the extension wire is colored differently, make sure that it is wired consistently.
Extension wire must be shielded twisted pair. Older MultiRanger products may have
included recommendations to use co-axial cable for noise reduction purposes. This is no
longer the case. Use shielded twisted pair. See the installation section for specifications.

Reducing Electrical Noise

• Ensure that the transducer cable does not run parallel to other cables carrying high
voltage or current.
• Move the transducer cable away from noise generators such as variable speed
drives.
• Put the transducer cable in grounded metal conduit.
• Filter the noise source.

Reducing Acoustical Noise

• Move the transducer away from the noise source.
• Use a stilling well.
• Install a rubber or foam bushing or gasket between the transducer and the
mounting surface.
• Relocate or insulate the noise source.
• Change the frequency of the noise. The MultiRanger is only sensitive to noise
between 25 KHz and 65 KHz.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 229

 Measurement Difficulties
If the Failsafe Timer (P070) expires due to a measurement difficulty, LOE flashes
alternately with the last known Reading. In rare cases, the MultiRanger may lock on to a
false echo and report a fixed or wrong reading.

Flashing LOE Display

The loss of echo (LOE) display appears when the echo confidence is below the threshold
value set in P805 Echo Confidence.
Appendix C: Troubleshooting

LOE occurs when:

• The echo is lost and no echo is shown above the ambient noise. See low echo
confidence (P805) and low echo strength (P806).
• Two echoes are too similar to differentiate. See low echo confidence (P805) and low
mmmmm

echo strength (P806).

If LOE is displayed, check the following:

• Surface monitored is within the transducer maximum range
• Transducer model (P004) matches the transducer used
• Transducer is located and aimed properly
• Transducer is not submerged without a submergence shield

Adjust Transducer Aiming

See the transducer manual for range, mounting, and aiming details. For optimum
performance, adjust transducer aiming to provide the best Echo Confidence (P805) and
Echo Strength (P806) for all material levels within the measurement range.
The most efficient method of checking echoes is with Milltronics Dolphin Plus software.

Displaying Echoes Editing Parameters

Use Dolphin Plus to graphically Edit the parameter values. Use

display the echo profile at the F1 to get online help at any
installation. Interpret the echo profile time.
and change relevant parameters.

Page 230 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 To display Echo Confidence in the RUN mode

Press and hold for four seconds (Failsafe Time Left changes to the Short:Long
Confidence display).
To display Echo Confidence in the program mode, access the Echo Confidence (P805)
parameter.
To update the value displayed after each aiming adjustment..

Press (five times or more to verify stability and overcome any echo lock P711).

Increase Failsafe Timer Value

Appendix C: Troubleshooting
Increase the Failsafe Timer (P070) value, if failsafe operation will not be compromised by
the larger value.

mmmmm
Try this only if LOE shows for short periods of time.

Install a Transducer with a Narrower Beam

Sometimes the interference echoes from the sides of a vessel can cause the MultiRanger
to lock onto a consistent, incorrect level. Try installing a longer range (narrower beam)
transducer, enter the new transducer model (P004), and (if necessary) optimize aiming
and frequency again.
Always contact your Siemens Milltronics service personnel before selecting a transducer
to solve this type of problem.

Use Dolphin Plus to Debug Echo

If a narrower beam transducer is not available, use Dolphin Plus to view live sonic
profiles and make adjustments to the Advanced Echo Processing parameters.
If you do not own Dolphin Plus, connect an oscilloscope and use the hand programmer to
adjust the same parameters. (See P810: Scope Displays.)

Fixed Reading
If the Reading is a fixed value, regardless of the transducer to material surface distance,
ensure the:
1. Transducer acoustic beam is free from obstruction.
2. Transducer is properly aimed
3. Transducer is not in contact with any metal object.
4. Material mixer (if used) is operating while the MultiRanger is operating. If it is
stopped, ensure that the mixer blade is not stopped under the transducer.

Obstructions in the Sound Beam

Check for (and remove if present) any acoustic beam obstruction, or relocate the
transducer.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 231

 If an obstruction cannot be removed or avoided, adjust the Time Varying Threshold (TVT)
Curve to reduce the Echo Confidence derived from the sound reflected by the obstruction.
Use Dolphin Plus to adjust the TVT curve or use an oscilloscope and a hand programmer
to adjust the required parameters. (See P810: Scope Displays and P832: TVT Shaper.)

Nozzle Mountings
If the transducer is mounted on or in a nozzle, grind smooth any burrs or welds on the
inside or open end (the end that opens into the vessel). If the problem persists, install a
larger diameter or shorter length nozzle, bevel the inside of the bottom end, or cut the
open end of the nozzle at a 45° angle.
Appendix C: Troubleshooting

See the transducer manual for complete mounting instructions.

For ST-series and XPS-10 transducers use the plastic conduit / flange adapter supplied
with the unit.
mmmmm

If the mounting hardware is over tightened, loosen it. Over tightening changes the
resonance characteristics of the transducer and can cause problems.

Set the MultiRanger to Ignore the Bad Echo

If the preceding remedies have not fixed the problem, the false echo has to be ignored.

If the Echo is Close to the Transducer

If there is a static, incorrect, high level reading from the MultiRanger there is probably
something reflecting a strong echo back to the transducer. If the material level never
reaches that point extend the Near Blanking (P800) to a distance to just past the
obstruction.

Adjust the TVT to Ignore the Echo

If increasing Near Blanking is unacceptable then the TVT Curve must be raised in the
area of the false echo to ignore the false echo.
Use Dolphin Plus to view live sonic profiles and make adjustments to the TVT curve.
If you do not own Dolphin Plus, connect an oscilloscope and use the hand programmer to
adjust the same parameters.
Continue making minor TVT Curve adjustments and taking new measurements while
observing the Echo Marker position until the Echo Lock Window repeatedly locks onto
the true echo. Verify the false echo is still ignored, regardless of the vessel material level,
or empty / fill activity. Finally, ensure that the true material level can still be measured in
the area where the TVT was adjusted.

Page 232 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Wrong Reading
If the Reading is erratic, or jumps to some incorrect value periodically, ensure the:
1. Surface monitored is not beyond the MultiRanger’s programmed range or the
transducer’s maximum range.
2. Material is not falling into the transducer’s acoustic beam.
3. Material is not inside the blanking distance of the transducer.

Types of Wrong Readings

Appendix C: Troubleshooting
If a periodic wrong Reading is always the same value, see Fixed Reading.
If the wrong Reading is random, ensure the material surface to transducer distance is
less than the Empty value entered plus 20%. If the material/object monitored is outside
this distance, increase Range Extension (P801) as required. This error is most common in

mmmmm
OCM applications using weirs.

Liquid Splashing
If the material monitored is a liquid, check for splashing in the vessel. Enter a lower
Maximum Process Speed (P003) value to stabilize the Reading, or install a stilling well.
(Contact Siemens Milltronics or your local distributor.)

Adjust the Echo Algorithm

Use Dolphin Plus to view live sonic profiles and make adjustments to the P820 Algorithm
parameter. See P820 on page 202 for details.
If you do not own Dolphin Plus, connect an oscilloscope and use the hand programmer to
adjust the same parameter.
If the “Area” algorithm is used and narrow noise spikes are evident on the (long shot)
Echo Profile, turn the Spike Filter (P821) on and/or widen the Narrow Echo Filter (P822).
Also, if the true echo has jagged peaks, use Reform Echo (P823).
If multiple echoes appear on the Echo Profile, typical of a flat material profile (especially if
the vessel top is domed), use the “first” Algorithm.
If the Echo Profile repeatedly switches from short to long, adjust the Short Shot Range
(P852) to stabilize the “shot” mode used for the echo evaluation. Also, adjust the Short
Shot Bias to increase (or decrease the amount of preference given to short shot echoes
over long shot echoes.
Should a stable measurement still not be attainable, contact Siemens Milltronics or your
local distributor.

Transducer Ringing
If the transducer is mounted too tightly, or if it is mounted so that its side touches
something, its resonance characteristics change and this can cause problems.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 233

 Normal Ring Down
Ring Down

Echo Profile
Appendix C: Troubleshooting
mmmmm

TVT curve
Time of Correct Echo

Poor Ring Down

Ring Down

Echo Profile

TVT Curve

Time of false echo from ringing

Ring down times that extend past the near blanking area can be interpreted by the
MultiRanger as the material level and are characterized by a steady high level being
reported.

Page 234 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

General Appendix D: Pump Control
Reference
Please note that some pump control features apply to the MultiRanger 200 only.
The MultiRanger has the pump control strategies to solve nearly any water / wastewater
application. This section details these strategies for engineers requiring in-depth
knowledge of the system and how it operates.

Pump Control Options

The various methods of pump control are made up of a combination of two control
variables:

Pump Duty
The pump duty indicates in what sequence pumps are started.

Pump Start Method

Appendix D: Pump Control

The start method indicates whether new pumps start and run with any currently running
pumps (most common) or whether new pumps start and shut off currently running
pumps.

mmmmm
Pump Groups
The MultiRanger groups pumps that use identical pumping strategies based on the value
of Relay Control Function (P111). Generally, one group of pumps corresponds to one wet
well or reservoir.

Pump by Rate [MR 200]

Please note that this feature applies to the MultiRanger 200 only.
To trigger pump starts by the rate of change in material level use P121–Pump by Rate
(P121). New pumps are started, one at a time, until the rate setpoint (Filling Indicator
(P702), or Emptying Indicator(P703)) is reached.

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 235

 Pump Control Algorithms
Please note that the MultiRanger 100 and the MultiRanger 200 use this feature
differently.

MultiRanger 100
All of these algorithms can be used to start multiple pumps (assist).

MultiRanger 200
All of these algorithms can be used to start multiple pumps (assist) or one pump at a time
(backup).

The MultiRanger 100 and MultiRanger 200 have three main methods of pump
control:

Fixed
Starts pumps based on individual setpoints and always starts the same pumps in the
same sequence.

Alternate
Appendix D: Pump Control

Starts pumps based on the duty schedule and always leads with a new pump.

Service Ratio
Starts pumps based on user-defined ratio of running time.
mmmmm

Fixed Duty Assist (P111 = 50)

Ties the indexed pump relay directly to the indexed setpoint.

Relay Operation (for P118 = 2)

The relay contact closes at the ON setpoint and opens at the OFF setpoint. Multiple relay
contacts in the pump group can be closed at the same time.

Relay Table
The following table shows relay status when each setpoint is reached.

Relays

Index 1 2 3

On 3 On On On
Setpoints

On 2 On On Off

On 1 On Off Off

Off 0 Off Off Off

Page 236 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Fixed Duty Backup (P111 = 51) [MR 200]
Ties the indexed pump relay directly to the indexed setpoint.
Please note that this feature applies to the MultiRanger 200 only.

Relay Operation (for P118 = 2)

The relay contact closes at the ON setpoint and opens at the OFF setpoint. When a new
relay trips the previously closed relay contact opens to shut down the running pump.
Only one relay contact in the pump group can be closed at any one time.

Relay Table
The following table shows relay status when each setpoint is reached.

Relays

Index 1 2 3

On 3 Off Off On
Setpoints

On 2 Off On Off

Appendix D: Pump Control

On 1 On Off Off

Off 0 Off Off Off

mmmmm
Alternate Duty Assist (P111 = 52)
Alternates the lead pump each time the material level cycles and runs all pumps together.

Relay Operation (for P118 = 2)

The setpoints associated with the relays are grouped so that they can be rotated.
Setpoint one does not relate directly to relay one. The pumping algorithm manages the
mapping of setpoints to relays.
When pumps are run, they RUN in parallel.

Relay Table

Cycle 1 Relays

1 2 3

On 3 On On On
Setpoints

On 2 On On Off

On 1 On Off Off

Off 0 Off Off Off

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 237

 Cycle 2 Relays
1 2 3

On 3 On On On
Setpoints On 2 Off On On

On 1 Off On Off

Off 0 Off Off Off

Cycle 3 Relays

1 2 3

On 3 On On On
Setpoints

On 2 On Off On

On 1 Off Off On

Off 0 Off Off Off

Alternate Duty Backup (P111 = 53) [MR 200]

Appendix D: Pump Control

Alternates the lead pump each time the material level cycles.
Please note that this feature applies to the MultiRanger 200 only.
mmmmm

Relay Operation (for P118 = 2)

The setpoints associated with the relays are grouped so that they can be rotated.
Setpoint one does not relate directly to relay one. The pumping algorithm manages the
mapping of setpoints to relays. When pumps are run, they can RUN only one at a time.

Relay Table

Cycle 1 Relays
1 2 3

On 3 Off Off On
Setpoints

On 2 Off On Off

On 1 On Off Off

0ff 0 Off Off Off

Page 238 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Cycle 2 Relays
1 2 3

On 3 On Off Off
Setpoints On 2 Off Off On

On 1 Off On Off

Off 0 Off Off Off

Cycle 3 Relays
1 2 3

On 3 Off On Off
Setpoints

On 2 On Off Off

On 1 Off Off On

Off 0 Off Off Off

Service Ratio Duty Assist (P111 = 54) [MR 200]

Appendix D: Pump Control

Selects the lead pump based on number of hours each pump has run and the specified
ratios that each pump requires. Multiple pumps can run at one time.

mmmmm
Please note that this feature applies to the MultiRanger 200 only.

Relay Operation (for P118 = 2) [MR 200]

Please note that this feature applies to the MultiRanger 200 only.
The setpoints associated with the relays are grouped so they can be redistributed based
on pump RUN time ratios. The next pump to start or stop is the one with the required time
to actual time ratio.
Over time the number of hours demanded of each pump will conform to the ratios
specified. Usually, the ratios are specified in percent values.
To create a grouping of pumps where two pumps make up 50% of the run time and the
third pump makes up the other 50%.
P122 is set to these values:

P122 Index Value

1 25

2 25

3 50

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 239

 Service Ratio Duty Backup (P111 = 55) [MR 200]
Selects the lead pump based on number of hours each pump has RUN and the specified
ratios that each pump requires. Only one pump can RUN at a time.
Please note that this feature applies to the MultiRanger 200 only.
This algorithm is the same as Service Ratio Duty Assist except that it will only RUN one
pump at a time. When the next pump in the sequence starts, the previous pump stops.

First In First Out (FIFO) (P111 = 56) [MR 200]

Selects the lead pump based on the Alternate duty but uses staggered off setpoints and
shuts down pumps based on the first in, first out rule.
Please note that this feature applies to the MultiRanger 200 only.
This algorithm starts pumps in the same way as Alternate Duty Assist but uses staggered
OFF setpoints to shut the pumps down. When the first OFF setpoint is reached the FIFO
rule shuts down the first pump started. If the pumps started in sequence 2,3,1 then they
would be shut down in sequence 2,3,1.

Pump by Rate (P121) [MR 200]

Appendix D: Pump Control

Starts pumps until the level is changing at the rate specified in P702 or P703.
Please note that this feature applies to the MultiRanger 200 only.
mmmmm

Pumping costs can be less because only the highest ON setpoint needs to be
programmed and this results in a lower difference in head to the next wet well which, in
turn, results in less energy being used to pump out the well.

Other Pump Controls [MR 200]

Please note that these features apply to the MultiRanger 200 only.
There are a number of other controls available to modify pump behaviour.

Pump Run-On (P130, P131)

Extends the RUN period for a pump based on the number of pump starts. This allows for
the wet well to be pumped lower than usual and reduces sludge build-up on the well
bottom.

Pump Exercising (P134)

Runs idle pumps and reduce the chance of seizing.

Wall Cling Reduction (P136)

Varies the ON and OFF setpoints to keep a fat ring from forming around the walls of the
wet well.

Page 240 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 Pump Group (P137)
Allows for two different Alternate Duty Assist or Alternate Duty Backup pump groups in
the same application.

Flush Device (P170 to P173)

Operates a flush valve or special flush device based on the number of pump starts,
usually to aerate wet well wastewater.

Appendix D: Pump Control

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 241

 General Appendix E: Updating Software

Updating Software
To update the software in the MultiRanger, please contact your Siemens Milltronics
representative to obtain the software. For a complete list of representatives, go to
[Link].

WARNINGS:
1. All parameter values will be lost during software upgrade.
Record your current parameters manually or using Dolphin Plus
before upgrade.
2. Disable all pumps and alarms before updating software, as
relays can change state during the software update causing pumps
to turn on or off .

To install the software, please complete the following:

1. Connect your PC or laptop to the MultiRanger RJ-11 RS-232 port.
2. Run the .exe Downloader program in the software. Use this to set the RS-232
settings to match your MultiRanger. Please note that the software default settings
will already match the default settings of the unit. Changes are only necessary if the
RS-232 settings in the unit have been changed.
3. Complete the Downloader program steps.
4. Verify that Downloader confirms a succesful upgrade before exiting.
5. Complete a Master Reset (P999) after a successful upgrade, before re-entering
parameters.
Appendix E: Updating Software
mmmmm

Page 242 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

General Appendix F: Upgrading
The following procedure will assist you if you are upgrading from a MultiRanger Plus to a
MultiRanger 100 or MultiRanger 200.
If the application is unchanged, copy down the parameters in the MultiRanger Plus
before de-commissioning the unit.

Mounting a MultiRanger 100/200

Please read the MultiRanger Installation section on page 7 before mounting the new
MultiRanger 100/200.
Make sure the power is OFF to the unit before following these steps:
1. Remove the old MultiRanger Plus.
2. Mount the new MultiRanger 100/200 using the same mounting holes.

Connecting the Transducer

Important: Unlike the MultiRanger Plus, coaxial cable is not recommended for use with
the MultiRanger 100/200 for transducer cable extensions. The MultiRanger 100/200
circuit is designed to use shielded twisted pair cable. Ideally, the coaxial cable should be
replaced with twisted pair.
If this is not practical, please refer to the Coaxial Transducer Extension section below.

Coaxial Transducer Extention

The MultiRanger 100/200 uses a new differential input receiver that works either directly
connected to the transducer lead or with a screened twisted pair extension cable via a
field junction box. This arrangement, using two conductors and a screen, gives
considerably better electrical noise immunity than the previous coaxial arrangement (up
to 20dB) and will give reliable operation in applications where the proximity of power
cables, variable speed drives etc. would have caused problems.
If you are installing a new MultiRanger system we strongly recommend that you use a
good quality screened, twisted pair cable if an extension is required. If the integral
transducer cable is used you need only connect to the MultiRanger and benefit from the
superior performance.
Appendix F: Upgrading

Transducer
mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 243

 Connecting a transducer with RG62 coaxial extension cable
If you are replacing an older Milltronics Ultrasonic Level Controller with a new
MultiRanger where an RG62 coaxial extension is fitted and you are unable to replace the
extension with a new cable, please refer to connection diagram below. Please note that
the noise immunity performance will be similar to our older model ultrasonic level
controllers if you use coaxial cable.

Existing installation
RG62 coaxial cable has been used to make the extension. The level controller might be a
MultiRanger Plus, HydroRanger, HydroRanger Plus or one of our other level controllers.

Transducer

MultiRanger 100/200 Installation (for retrofitting MultiRanger Plus

Installations)
Connect with a 0.1µF (100v or greater) capacitor (included with MultiRanger) between the
shield and negative terminals. Connect centre core of the coaxial to the positive terminal
and the screen to the negative terminal.

Transducer
Appendix F: Upgrading
mmmmm

Page 244 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

MultiRanger Plus to MultiRanger 100/200 Parameters
The MultiRanger 100/200 uses the current Milltronics standard parameter set which is
different than the parameter numbers used in the MultiRanger Plus.
The MultiRanger Plus parameters numbers are sequential (P-0 to P-99). The MultiRanger
100/200 parameters number are also sequential; however, some of the parameters are
indexed.
Parameters are indexed when they apply to more than one input or output. The index
value defines the input/output for that parameter. Indexed parameters contain a value for
each index, even if that index is not used.

Example
In the MultiRanger Plus each relay had a dedicated parameter number for its function,
ON and OFF points.
MultiRanger Plus Relay One
• P-8: Function
• P-9 : ON setpoint
• P-10: OFF setpoint
MultiRanger 100/200 uses P111 for all relays and indexes these parameters.
• P-111: Function
• P-112: ON
• P-113: OFF

The following tables show the differences between the MultiRanger Plus and the
MultiRanger 100/200. They each show one relay programmed as a high alarm, and two
relays programmed for pump control with alternating pump starts:

MultiRanger Plus MultiRanger 100/200

Relay Parameter Value Relay Parameter Value
1 P-8 (relay function) 1 (alarm) 1 P111 [1] (relay function) 1
1 P-9 (ON setpoint) 4m 1 P112 [1] (ON setpoint) 4m
1 P10 (OFF setpoint) 3.5 m 1 P113[1] (OFF setpoint) 3.5 m
2 P-11 (relay function) 9 2 P111[2] (relay function) 52
2 P-12 (ON setpoint) 3.2 m 2 P112[2] (ON setpoint) 3.2 m
2 P-13 (OFF setpoint) 0.5 m 2 P113[2] (OFF setpoint) 0.5 m
3 P-14 (relay function) 9 3 P111[3] (relay function) 52
3 P-15 (ON setpoint) 3.4 m 3 P112[3] (ON setpoint) 3.4 m
3 P-16 (OFF setpoint) 0.6 m 3 P113[3] (OFF setpoint) 0.6 m
Appendix F: Upgrading

mmmmm

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 245

 6.33

Page 246
9.46

NOTES:
1) USE ONLY CONDUIT HUBS CERTIFIED / APPROVED AS TYPE 4X.

2) NON METALLIC ENCLOSURE DOES NOT PROVIDE GROUNDING BETWEEN CONDUIT CONNECTIONS.
USE GROUNDING TYPE BUSHINGS AND JUMPER WIRES.

3) DIMENSIONS INCHES

WARNING: EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY IMPAIR

SUITIBILITY FOR CLASS I, DIVISION 2
Class 1, Div 2 Applications

0.875

MultiRanger – INSTRUCTION MANUAL

0.94
1.50
2.62 FOR CONSTRUCTION SN AUG
0 RPC 14/02

Product Group
ULTRASONICS
NONE
14/ AUG / 02
DRILL FOR 3/4” R. CLYSDALE
DRILL FOR 1/2” CONDUIT HUB HINGED 6 X 9 ENCLOSURE WITH
T. ADAM
CONDUIT HUBS 1.688 CONDUIT ENTREES & ASSEMBLE
S. NGUYEN
FOR CLASS 1 DIV 2 APPLICATIONS
3.25 PETERBOROUGH

4.625 23650314
General Appendix G: Conduit Entry for

0
2365031400 1:1 1 2

7ML19981FB02
7ML19981FB02
DISPLAY

TB2

1
2
BOARD
1.75”, 6-32

REL AY 6
REL AY 5
REL AY 4
REL AY 3
REL AY 2
REL AY 1
NYLON
STANDOFF
1.75” , 6-32
BRASS
STANDOFF
(3 PLACES)

INPUTS
DISCRETE
2
1

RS4 85
1.12” RICHCO

4 - 20 mA
OUTPU TS
mA INP UT

TS-3
L2/N L1

COM

B
A
SYNC

2
1

SHIELD
SHIELD
DUAL LOCKING

TB1

TB3
MINI NYLON POWER
STANDOFF SUPPLY
(4 PLACES) BOARD

CERTIFIED
TYCO ELECTRONICS
MODULAR PLUG
5-641335
(SUPPLIED BY
CUSTOMER)

CERTIFIED MAIN
TYCO ELECTRONICS BOARD
MODULAR JACK
520425-2
(INSTALLED BY

MultiRanger – INSTRUCTION MANUAL

SIEMENS MILLTRONICS)

AUG
0 FOR CONSTRUCTION RPC SN 14/02

Product Group
ULTRASONICS
NONE
14/ AUG / 02
R. CLYSDALE
HINGED 6 X 9 ENCLOSURE WITH
T. ADAM
CONDUIT ENTREES & ASSEMBLE
S. NGUYEN
FOR CLASS 1 DIV 2 APPLICATIONS
PETERBOROUGH

23650314 0
2365031400 1:1 2 2

Page 247
Notes

Page 248 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

Index
A D
accuracy 4 data types 101

Index
mmmmm
adding new functions 242 bit values 101
alarm 48 default auxiliary reading 21
bounded 50 dimensions 8, 34
cable fault 50 discrete inputs 42, 94
common parameters 48 indexing 30
emptying rate 49 logic 42
filling rate 49 wiring 42
level 48 display 4
loss of echo 51 auxiliary 20
rate 49 controlling 20
temperature 50 distance 18
alternate duty assist 237 echo confidence 18
alternate duty backup 53, 54, 55, 238 failsafe time left 18
alternate duty service 56 head (OCM) 18
application multiple readings 21
test 81 pump hours 18
applications rate of change 18
preset 40 temperature 18
testing 79 display readout 28
approvals 6 distance calculation 221
auxiliary reading 20 Dolphin Plus 24, 29, 83
B changing parameters 29
backup level override 41 communication settings 85
battery 10 updating software 242
bit values 101 E
blanking echo confidence, run mode 18
troubleshooting 232 echo processing 220
with Span 119 echo profile example 198
board 9 enabling new functions 242
C enclosure 6
cable 12 error codes 28, 111
routing 8 error handling 106
cabling guidelines 86 exponential flow 73
calibration external totalizers 65
mA output 43 F
characterization chart 46 failsafe 34
communication ports by relay 39
configuring 88 fat ring 60
communications 83 first in first out (FIFO) 56, 240
communications installation 86 fixed duty assist 55
configuration 2 flash update 242
control flow calculation 223
rake 63 flow sampler 66
controlling the display 20 flume
cut throat 76

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 249

 H flume 72 setting up 32
Leopold Lagco 75 single point 32
Palmer Bowlus 71 starting 32
Parshall 74, 78 Modbus 84
rectangular 70 register map 91
Index
mmmmm

universal trapezoidal 78 responses 106

flush valve 61 mode
format words 99 program 22
Frequency Input 149 run 17
G mounting
global index method 97 instructions 8
group pumps 61 location 7
H wall mount 8
H flume 161 multiple readings 21
hand programmer 22 N
head measurement 18 near blanking
head vs. flowrate breakpoints 168 troubleshooting 232
I with span 119
in bounds 50 noise problems 227
independent failsafe 59 noise sources 228
index method O
global 97 OCM (open channel monitoring) 67
parameter specific 98 common parameters 67
index types 219 cut throat 76
indexed parameters 31 flow characterization chart 77
indexing flow exponent support 73
parameters 30 H flume 72
points 30 Leopold Lagco flume 75
input / output 93 Palmer Bowlus flume 71
inputs 5 Parshall flume 74
installation 7 rectangular flume 70
L testing flow values 80
LCD controlling 20 totalized volume 69
level alarms 48 universal calculation 77
LOE 51 universal Parshall flume 78
loss of echo (LOE) 34 universal trapezoidal flume 78
alarm 51 V notch weir 69
M weirs 73
mA zero head 68
calibrating 43 operation
input 43 dual point 33
loops 43 single point 32
output 43, 44 options, adding 242
map ID 92 out of bounds 50
maximum process speed 225 outputs 5
maximum separation 86 P
measurement parameter
difficulties 230 relays 37
dual point 33 parameter access
set up 32 data types 101

Page 250 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

 format words 99 temperature compensation 177
overview 96 test 211
reading 97 totalizer 171
writing 98 transducer scanning 186
parameter indexing 30, 96 view only 27

Index
mmmmm
parameters volume 119
advanced echo processing 198 volume measurement 216
advanced shot adjustment 208 points
advanced TVT adjustment 205 indexing 30
auto record setpoints 158 ports, communication 84
backup level override 125 power 15
calibration 174 preprogrammed applications 40
communications 190 program mode 22
data logging 150 programming 4
discrete input functions 149 alarms 48
display 187 by hand 22
display and reading 123 relays 35
echo processing 195 pump
failsafe 127 alternate duty backup 53, 54
flow records 153 by rate 57
flush systems 140 hours 18
global 27 off setpoint 53, 54, 55
independent mA setpoints 144 on setpoints 53, 54, 55
independent relay failsafe 136 other controls 55
installation records 160 pump down 52
LCD totalizer 154 pump up 53
mA input 147 reservoir 53
mA output 142 run-on 60
mA output failsafe 146 service ratio 58
mA output limits 145 start delay 60
mA output trim 146 start method 235
master reset 218 totalizing volume 59
measurement 215 usage 62
measurement verification 183 wet well 52
open channel monitoring (OCM) 161 pump by rate 240
profile pointer 200 pump control 94
profile records 155 algorithms 52, 236
pump control modifiers 137 options 235
pump records 152 other 240
pump setpoint modifiers 135 reference 235
pumped volume totalizer 170 pump flush valve 61
quick start 115 pump hours 95
rate 179 pump starts 95
record readings 152 Q
record temperatures 150 quick start 32
relays 128 R
scrolling 26 rake control 63
SmartLinx hardware testing 193 randomize setpoints 60
SmartLinx reserved 190 range 3
special 27 reading
status 19

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 251

 volume 45 single measurement 79
recording profiles 156 volume characterization 80
register map 91 single parameter access 109
discrete inputs 94 single point 32
input/output 93 SmartLinx 85
Index
mmmmm

mA output 94 installation 10
map ID 92 Installation in Wall mount 10
parameter access 96 software update 242
parameter format words 99 sound velocity 221
point data 93 special parameters 27
product ID 93 specific auxiliary reading 21
pump control 94 specifications 3
pump hours 95 standard applications 40
pump setpoint 94, 95 start delay 60
pump starts 95 starting measurement 32
pumped volume 95 status parameters 19
relay outputs 94 synchronization 15
UINT32 Order 92 T
relay 13 tank shape 45
activation 38 temperature
failsafe 39 alarm 50
flow sampler 66 compensation 4
function codes 104 error 4
indexing 30 run mode 18
modifiers 37 sensor 14
modify logic 39 terminal board 12
outputs 94 testing
parameters 37 application 81
programming 35 configuration 79
totalizer 65 text messages 103
wiring test 38 totalizer 65
resolution 4 transducers 6, 13
response rate 34 indexing 30
RS-232 16 transmit pulse 220
RS-485 16 troubleshooting
run mode 17 common problems 226
run-on 60 communication 108
S noise problems 227
samplers 65 TS-3 14
SCADA 83 U
scrolling parameters 26 UINT32 101
scum ring See wall cling 60 units or percent 27
security 27 universal
service ratio example 46
applications 58 volume 46
duty assist 239 unsigned double precision integer 101
duty backup 240 updating software 242
simulation 79 V
level cycle 79 verify
OCM flow characterization 80 mA output 44

Page 252 MultiRanger – INSTRUCTION MANUAL 7ML19981FB02

volume 45
calculation 222
characterization chart 46
dimensions 34
readings 45

Index
mmmmm
tank shape 45
universal example 46
W
wall cling 60
weight 6
weir
Cipolletti 163
standard 73
V notch 69
wet well 52
wiring 11
communication 86
problems 229
test 38
writing parameters 98
wrong reading 233

7ML19981FB02 MultiRanger – INSTRUCTION MANUAL Page 253

 [Link]

Siemens Milltronics Process Instruments Inc. Siemens Milltronics Process Instruments Inc. 2003
1954Technology Drive, P.O. Box 4225 Subject to change without prior notice
Peterborough, ON, Canada K9J 7B1
Tel: (705) 745-2431 Fax: (705) 741-0466 Rev. 2.0
Email: techpubs@[Link]
*7ml19981FB02*
Printed in Canada