Scribd
Upload
167 views3 pages

Footing and Beam Design Calculations

This document provides design details for a footing (F1) and beam/slab. For the footing, it gives input parameters like load, bearing capacity, dimensions. It then calculates output values like required steel reinforcement and checks punching and shear. For the beam/slab, it similarly provides input/output values for steel reinforcement calculations and checks shear. The document summarizes reinforcement design calculations and checks for different structural elements.

Uploaded by

g4gohar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
167 views3 pages

Footing and Beam Design Calculations

This document provides design details for a footing (F1) and beam/slab. For the footing, it gives input parameters like load, bearing capacity, dimensions. It then calculates output values like required steel reinforcement and checks punching and shear. For the beam/slab, it similarly provides input/output values for steel reinforcement calculations and checks shear. The document summarizes reinforcement design calculations and checks for different structural elements.

Uploaded by

g4gohar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd

Design Of Footing F1

Pw bearing capacity Area of P.C Dimention of R.C Dimention of Col Factor


95 18 5.28 1.25 1.5 0.25 0.5 0.25
Input data: Dim of P.C Footing 2.25 2.5
Mw 6.33 Estimating area of P.C 5.63
Fcu 250 6.33 depth of P.C 40 safe
Moment
Fy 3600 6.33 P.C Root 2.29734
B 100 depth of R.c 50
d 43

Output Data:
C1 6.976
J 0.826
As 7.430

Dim of bar 8 10 12 16 18 20 22 25 28 32
Area of bar 0.503 0.785 1.13 2.01 2.55 3.14 3.80 4.91 6.16 8.05
No of bar 14.8 9.46 6.57 3.69 2.92 2.36 1.95 1.51 1.21 0.92

Check punching :

Qp 10.29 < limit 12.900

Check shear :

Qs 14.93 < limit


Design Of Beam / Slab

Input data:
Mw 5
Fcu 350
Fy 3600
B 30
d 75

Output Data: Minimum Steel RFT :


C1 8.87 As1= 6.875 cm2
J 0.826 As2= 4.371805 cm2
As(req) 3.363 cm2 As3= 3.375 cm2
As(min)= 4.371805 cm2 use minimum steel RFT

Dim of bar 8 10 12 16 18 20 22 25 28 32
Area of bar 0.503 0.785 1.13 2.01 2.55 3.14 3.80 4.91 6.16 8.05
No of bar 6.7 4.28 2.97 1.67 1.32 1.07 0.88 0.68 0.55 0.42

Check shear : Results


1 design for shear
Qw 35 2 safe shear
no. of branches = 2.00 branches 3 ok
qc 11.46
qmax 33.6
qs 23.33

Dim of bar 8 10 12
No of bar 25.17 Fy 2400
10.7 Fy 3600 7.46

You might also like