The University of Technology, Jamaica Electronic Devices 1 Rectification and smoothing circuits Monique Hepburn 1001296
OBJECTIVE
To investigate rectification and smoothing circuits.
PRELAB/THEORY
Half-wave rectification The diagram below shows a half wave rectifier. A rectifier is a circuit which converts ac to dc current. The input signal will be a full sine wave whereas the output signal would be that as shown in the graph below. The current will flow towards the anode of the diode and through it but in the opposite direction of current flow the diode blocks the current. This is the reason for the attained output graph.
Full wave rectifier
In the diagram above the current in the forward direction will flow through the red diodes. The current in the opposite direction will allow current through the blue diodes. This will produce a full wave rectification as shown in the graph below.
Capacitor Smoothing
When the voltage increases during the first half of the voltage peaks from the rectifier, the capacitor charges up. Then as the voltage decreases to zero in the second half of the peaks, the capacitor issues its stored energy the keep the output voltage constant. The diagram below shows the smoothing effect.
Equipment
Oscilloscope Digital Multimeter 12V Centre tap transformer (2) 2.2kohm resistor (4) Silicon diode 10microFarad Capacitor 100microFarad Capacitor
Procedure
Half Wave rectification The circuit of a half wave rectifier was constructed. A labelled sketch of the input and voltage was made. The peak voltage value was recorded in the sketch to calculate the DC level of the signal. The DC output was measured and recorded with the multimeter. Full wave rectification The circuit of a full wave rectifier was constructed.
A sketch of the voltage at the points A, B and the output voltage was made. The average or equivalent DC level of a full wave signal is 63.6 percent of the peak value. The peak voltage was recorded in the sketch to calculate the DC level of the signal. The value of the DC output was measured and recorded. Full wave rectifier and smoothing A similar circuit was constructed as before with a transformer included. A labeled sketch of the input voltage and output voltage was made. The peak voltage was recorded in the sketch to calculate the DC level of the signal. The DC output was measured. The 10 microfarad capacitor was placed across the output of the bridge rectifier. The oscilloscope was used to view the output voltage. A sketch was made of the output. The capacitor was replaced by the 100 micro farad capacitor and the oscilloscope was used to record the output voltage. A sketch was made of this output. The 2.2 Kohm resistor was placed in parallel with the one of the circuit and the effect of the output ripples was noted.
Results
(see attachment)
Replacing the 10 microfarad with a 100 microfarad gives a straight line Volts against milliseconds
Placing the 2.2 kilo-ohm resistor with the 100 microfarad gives a straight line Volts against milliseconds
Analysis of Results
The DC level of the half wave rectification was less than the DC level of the full wave rectified circuit. This was expected based on the formula used to calculate the DC levels of both circuits. The full wave circuit dc voltage must obviously higher voltage level. The measured and calculated values for the half wave rectifier were found to be similar: 2.64 volts for the calculated value and the measured for the half wave was found to be [Link] the full wave, the DC output was found to be 6.31V and the calculated value was [Link] the half peak, the value of the calculated voltage was found to be 5.06V. The DC voltage was found to be 1.18V. When the voltage increases during the first half of the voltage peaks from the rectifier, the capacitor charges up. Then as the voltage decreases to zero in the second half of the peaks, the capacitor issues its stored energy the keep the output voltage constant. This is what accounts for the ripple. Where a capacitor is placed in parallel with a load its voltage will be affected by the time constant T = RC. The larger the capacitance the higher will be T, hence, the ripple factor will be lower.
Conclusion
The concept of full wave rectification and half wave rectification was appreciated as well as that for the smoothing effect. It was understood how to find the DC voltage via calculation. The graphs obtained match the theoretical concept behind half wave and full wave rectification.
References
Giancoli. D.C, (2000).Physics for Scientists and Engineers with Modern Physics 4th edition. Pearson Education Inc, Prentice Hall.
Robert Boylestead, Louis Nashelsky(2005 updated ). Electronic Devices and Circuit Theory seventh edition.
