The Routing Table: A Closer Look
Routing Protocols and Concepts Chapter 8
Version 4.0
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Objectives
Describe the various route types found in the routing table structure. Describe the routing table lookup process. Describe routing behavior in routed networks.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Introduction
Chapter focus: Structure of the routing table. Lookup process of the routing table.
Classless and classful routing behaviors.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Lab topology 3 router setup:
R1 and R2 share a common [Link]/16 network with [Link]/24 subnets R2 and R3 are connected by the [Link]/24 network R3 also has a [Link]/24 subnet, which is disconnected, or discontiguous, from the [Link] network that R1 and R2 share
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Routing table entries come from the following sources:
Directly connected networks Static routes Dynamic routing protocols
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Level 1 routes
As soon as the no shutdown command is issued the route is added to routing table
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Cisco IP routing table is a hierarchical structure The reason for this is to speed up lookup process
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Level 1 routes:
Have a subnet mask equal to or less than the classful mask of the network address
Level 1 routes can function as:
Default routes Supernet routes Network routes
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Level 1 routes:
Ultimate routes includes either: A next-hop address OR
An exit interface
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Structure
Parent and child routes:
A parent route is a level 1 route A parent route does not contain any nexthop IP address or exit interface information
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
10
Routing Table Structure
Automatic creation of parent routes:
Occurs any time a subnet is added to the routing table
Child routes:
Child routes are level 2 routes Child routes are a subnet of a classful network address
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
11
Routing Table Structure
Level 2 child routes contain route source and the network address of the route
Level 2 child routes are also considered ultimate routes
Reason: they contain the next hop address and/or exit interface
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
12
Routing Table Structure
Both child routes have the same subnet mask. This means the parent route maintains the /24 mask
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
13
Routing Table Structure
Diagram illustrates 2 child networks belonging to the parent route [Link] / 24:
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
14
Routing Table Structure
In classless networks, child routes do not have to share the same subnet mask.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
15
Routing Table Structure
Parent & Child Routes: Classless Networks
Network type Parent routes classful mask is displayed Term variably subnetted is seen in parent route in routing table Includes the Subnet mask # of different included masks of with each child routes child route entry
Classful Classless
No Yes
No Yes
No Yes
No Yes
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
16
Routing Table Structure
Parent & Child Routes: Classless Networks
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
17
Routing Table Lookup Process
The Route Lookup Process
Examine level 1 routes: If best match a level 1 ultimate route and is not a parent route this route is used to forward packet Router examines level 2 (child) routes: If there is a match with level 2 child route then that subnet is used to forward packet If no match then determine routing behavior type Router determines classful or classless routing behavior: If classful then packet is dropped If classless then router searches level one supernet and default routes If there exists a level 1 supernet or default route match then Packet is forwarded, if not packet is dropped
18
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
Routing Table Lookup Process
Longest Match: Level 1 Network Routes:
Best match is also known as the longest match
The best match is the one that has the most number of left most bits matching between the destination IP address and the route in the routing table
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
19
Routing Table Lookup Process
Finding the subnet mask used to determine the longest match
Scenario: PC1 pings [Link] Router examines level 1 route for best match There exist a match between [Link] and [Link] / 24 Router forwards packets out s0/0/0
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
20
Routing Table Lookup Process
The process of matching:
1st there must be a match made between the parent route & destination IP If a match is made then an attempt at finding a match between the destination IP and the child route is made
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
21
Routing Table Lookup Process
Finding a match between the packets destination IP address and the next route in the routing table:
The figure shows a match between the destination IP of [Link] and the level one IP of [Link] / 24 then packet forwarded out s0/0/0
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
22
Routing Table Lookup Process
Level 1 Parent & Level 2 Child Routes
Before level 2 child routes are examined
There must be a match between classful level one parent route and destination IP address
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
23
Routing Table Lookup Process
After the match with parent route has been made Level 2 child routes will be examined for a match
Route lookup process searches for child routes with a match with destination IP
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
24
Routing Table Lookup Process
How a router finds a match with one of the level 2 child routes:
First router examines parent routes for a match. If a match exists then:
Child routes are examined Child route chosen is the one with the longest match
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
25
Routing Table Lookup Process
Example Route Lookup Process with VLSM:
The use of VLSM does not change the lookup process If there is a match between destination IP address and the level 1 parent route then Level 2 child routes will be searched
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
26
Routing Behavior
Classful & classless routing protocols:
Influence how routing table is populated
Classful & classless routing behaviors:
Determines how routing table is searched after it is filled
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
27
Routing Behavior
Classful Routing Behavior: no ip classless What happens if there is not a match with any level 2 child routes of the parent?
Router must determine if the routing behavior is classless or classful If router is utilizing classful routing behavior then lookup process is terminated and packet is dropped
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
28
Routing Behavior
Classful Routing Behavior Search Process An example of when classful routing behavior is in effect and why the router drops the Packet
The destinations subnet mask is a /24 and none of the child routes left most bits match the first 24 bits. This means packet is dropped.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
29
Classful Routing Behavior Search Process The reason why the router will not search beyond the child routes:
Originally networks were all classful This meant an organization could subnet a major network address and enlighten all the organizations routers about the subnetting Therefore, if the subnet was not in the routing table, the subnet did not exist and packet was dropped
Routing Behavior
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
30
Routing Behavior
Classless Routing Behavior: ip classless Beginning with IOS 11.3, ip classless was configured by default Classless routing behavior works for:
Discontiguous networks and CIDR supernets
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
31
Routing Behavior
Classless Routing Behavior: ip classless Route lookup process when ip classless is in use:
If classless routing behavior in effect then:
Search level 1 routes Supernet routes checked first
If a match exists then forward packet
Default routes checked second
If there is no match or no default route then the packet is dropped
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
32
Routing Behavior
Classless Routing Behavior Search Process Router begins search process by finding a match between destination IP and parent route
After finding the above mentioned match, then there is a search of the child route
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
33
Routing Behavior
Classless Routing Behavior Search Process
If no match is found in child routes of previous slide then:
Router continues to search the routing table for a match that may have fewer bits in the match
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
34
Routing Behavior
Classful vs. Classless Routing Behavior:
It is recommended to use classless routing behavior
Reason: so supernet and default routes can be used whenever needed
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
35
Summary
Content / structure of a routing table: Routing table entries:
Directly connected networks Static route Dynamic routing protocols
Routing tables are hierarchical:
Level 1 route: Have a subnet mask that is less than or equal to classful subnet mask for the network address. Level 2 route: These are subnets of a network address.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
36
Summary
Routing table lookup process:
Level 1 route examination: Begins with examining level 1 routes for best match with packets destination IP. If the best match equals an ultimate route then packet is forwarded, or else Parent route is examined. If parent route & destination IP match then Level 2 (child) routes are examined. Level 2 route examination: If a match between destination IP and child route found then packet forwarded, or else If Router is using classful routing behavior then packet is dropped, or else If router is using classless routing behavior then router searches Level 1 supernet and default routes for a match. If a match is found then Packet is forwarded, or else Packet is dropped.
2007 Cisco Systems, Inc. All rights reserved. Cisco Public
37
Summary
Routing behaviors:
This refers to how a routing table is searched.
Classful routing behavior:
Indicated by the use of the no ip classless command.
Router will not look beyond child routes for a lesser match.
Classless routing behavior:
Indicated by the use of the ip classless command. Router will look beyond child routes for a lesser match.
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
38
2007 Cisco Systems, Inc. All rights reserved.
Cisco Public
39
